Scribd
Upload
82 views

A. Destructive Weld Testing

This document summarizes different types of weld testing methods, including destructive and non-destructive tests. Destructive tests physically damage the welded joint to obtain quantitative data, while non-destructive tests do not damage the joint and provide qualitative data. Some key destructive tests described are tensile testing, bend testing, hardness testing, and toughness testing. Major non-destructive tests covered include dye penetrant inspection, magnetic particle inspection, radiography, ultrasonic testing, and eddy current testing.

Uploaded by

Ashok Pradhan
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
82 views

A. Destructive Weld Testing

This document summarizes different types of weld testing methods, including destructive and non-destructive tests. Destructive tests physically damage the welded joint to obtain quantitative data, while non-destructive tests do not damage the joint and provide qualitative data. Some key destructive tests described are tensile testing, bend testing, hardness testing, and toughness testing. Major non-destructive tests covered include dye penetrant inspection, magnetic particle inspection, radiography, ultrasonic testing, and eddy current testing.

Uploaded by

Ashok Pradhan
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Weld Testing

• Types
– Destructive
• Physical damage to w/p and welded join.
• Quantitative data obtained
– Non Destructive
• Without Physically damaging the workpiece and joint
• Qualitative data is obtained

A. Destructive Weld Testing


• Destructive test, some sort of the damage takes place in the component which is being tested, the extent of damage
may be more or less, butmost of the time it is observed that component, which has been tested by the destructive test
is damaged to such as extent that it cannot be used for further, for the targeted application.
Types of Destructive Weld Testing
• Tensile Test
• Bend Test
• Hardness Test
• Toughness Testing
• Fatigue Behavior

i. Tensile Testing
• Tensile test is used to check how the weld joint will perform under tensile loading and under different environment.
• Modulus of elasticity, Yield strength Ultimate strength, kind of the deformation at the different stages and the total
elongation of the weld joint, till the fracture.
• Most simple and common method.

ii. Bend Test


• Bend test is one of the most important and commonly used destructive test to determine,
– Ductility &,
– Soundness of the welded joints in terms of porosity, inclusion, penetration & other macro size weld discontinuities.
• The outside of the bend is extensively plastically deformed so that any defects in, or embrittlement of, the material
will be revealed by the premature failure of the coupon.
Hardness Test
• It is resistance to indentation or penetration. Usually referred as a measure of resistance to abrasion or scratch.
• Due to application of heat in welding, materials like hard enable steels, castiorns are subjected to hardening where as
materials like aluminum alloys (precipitation enabled) become softer.
• Hardening and softening phenomenon usually occurs at HAZ.
• The hardness test, is very simple test and it gives the lot of information about, that if any micro structural
transformation has taken place or any embrittlement has taken place due to the application of the weld thermal cycle.
iii. Toughness Test
• Toughness is the ability of a material to resist both fracture and deformation.
• The toughness test simulates service conditions often encountered by components of the system used in
transportation, agricultural, and construction equipment.
• Can be determined by calculating energy absorbed by material before fracture.
B. Non Destructive Testing
• Nondestructive testing or Non-destructive testing (NDT) is a wide group of analysis techniques used in science and
technology industry to evaluate the properties of a material, component or system without causing damage.
Major types of NDT
• Detection of surface flaws
 Visual
 Magnetic Particle Inspection
 Fluorescent Dye Penetrant Inspection
• Detection of internal flaws
 Radiography
 Ultrasonic Testing
 Eddy current Testing
i. Dye Penetrant Inspection
Liquid penetrant inspection (LPI) is one of the most widely used nondestructive evaluation (NDE) methods.
Its popularity can be attributed to two main factors, which are its relative ease of use and its flexibility. LPI
can be used to inspect almost any material provided that its surface is not extremely rough or porous. Materials that
are commonly inspected using LPI include metals (aluminum, copper, steel, titanium, etc.), glass, many ceramic
materials, rubber, and plastics.
Why Liquid Penetrant Inspection?
• To improves the detectability of flaws There are basically two ways that a penetrant inspection process
makes flaws more easily seen.
(1) LPI produces a flaw indication that is much larger and easier for the eye to detect than the flaw itself.
(2) LPI produces a flaw indication with a high level of contrast between the indication and the background.
ii. Magnetic Particle Inspection (MPI)
• A nondestructive testing method used for defect detection. Fast and relatively easy to apply and part surface
preparation is not as critical as for some other NDT methods. – MPI one of the most widely utilized nondestructive
testing methods.
• MPI uses magnetic fields and small magnetic particles, such as iron filings to detect flaws in components.
• The only requirement from an inspectability standpoint is that the component being inspected must be made of a
ferromagnetic material such as iron, nickel, cobalt, or some of their alloys. Ferromagnetic materials are materials that
can be magnetized to a level that will allow the inspection to be affective.
Advantages of MPI

One of the most dependable and sensitive methods for surface defects
• fast, simple and inexpensive
• direct, visible indication on surface
• unaffected by possible deposits, e.g. oil, grease or other metals chips, in the cracks
• can be used on painted objects
• surface preparation not required
• results readily documented with photo or tape impression.

Limitations of MPI
• Only good for ferromagnetic materials
• sub-surface defects will not always be indicated
• relative direction between the magnetic field and the defect line is important
• objects must be demagnetized before and after the examination
• the current magnetization may cause burn scars on the item Examined.
iii. Radiography
Radiography involves the use of penetrating gamma- or X-radiation to examine material's and product's defects and
internal features. An X-ray machine or radioactive isotope is used as a source of radiation. Radiation is directed through
a part and onto film or other media. The resulting shadowgraph shows the internal features and soundness of the part.
Material thickness and density changes are indicated as lighter or darker areas on the film. The darker areas in the
radiograph below represent internal voids in the component.
iv. Ultrasonic Testing

In ultrasonic testing, high-frequency sound waves are transmitted into a material to detect imperfections or to locate
changes in material properties The most commonly used ultrasonic testing technique is pulse echo, whereby sound is
introduced into a test object and reflections (echoes) from internal imperfections or the part's geometrical surfaces are
returned to a receiver. The time interval between the transmission and reception of pulses give clues to the internal
structure of the material.
v. Eddy Current Testing
Electrical currents are generated in a conductive material by an induced alternating magnetic field. The electrical
currents are called eddy currents because the flow in circles at and just below the surface of the material. Interruptions
in the flow of eddy currents, caused by imperfections, dimensional changes, or changes in the material's conductive and
permeability properties, can be detected with the proper equipment.
• Eddy current testing can be used on all electrically conducting materials with a reasonably smooth surface.
• The test equipment consists of a generator (AC power supply), a test coil and recording equipment, e.g. a
galvanometer or an oscilloscope • Used for crack detection, material thickness measurement (corrosion detection),
sorting materials, coating thickness measurement, metal detection, etc.

You might also like