J

S T

Technical Data of Pipes Conforming To DIN: 2440

Mass of Tube Pipe Thread Sockets
Normal Outside Wall
Size Diameter Thickness Thread No. of Thread Min. Outside Min.
Plain End Socketed Diameter Length
In 25.4mm Diameter
DN Min.(mm) Max.(mm) mm Kg/m Kg/m mm mm
15 21.0 21.8 2.65 1.22 1.23 20.955 14 26.4 34
20 26.5 27.3 2.65 1.58 1.59 26.441 14 31.8 36
25 33.3 34.2 3.25 2.44 2.46 33.249 11 39.5 43
32 42.0 42.9 3.25 3.14 3.17 41.910 11 48.3 48
40 47.9 48.8 3.25 3.61 3.65 47.803 11 54.5 48
50 59.7 60.8 3.65 5.10 5.17 59.614 11 66.3 56
65 75.3 76.6 3.65 6.51 6.63 75.184 11 82.0 65
80 88.0 89.5 4.05 8.47 8.64 87.884 11 95.0 71
100 113.1 115.0 4.50 12.10 12.40 113.030 11 122.0 83
125 138.5 140.8 4.85 16.20 16.70 138.430 11 147.0 92
150 163.9 166.5 4.85 19.20 19.80 163.830 11 175.0 92

Technical Data of Pipes Conforming To DIN: 2441

Mass of Tube Pipe Thread Sockets
Normal Outside Wall
Size Diameter Thickness Thread No. of Thread Min. Outside Min.
Plain End Socketed Length
Diameter In 25.4mm Diameter
DN Min.(mm) Max.(mm) mm Kg/m Kg/m mm mm
15 21.0 21.8 3.25 1.45 1.46 20.955 14 26.4 34
20 26.5 27.3 3.25 1.90 1.91 26.441 14 31.8 36
25 33.3 34.2 4.05 2.97 2.99 32.249 11 39.5 43
32 42.0 42.9 4.05 3.84 3.87 41.910 11 48.3 48
40 47.9 48.8 4.05 4.43 4.47 47.803 11 54.5 48
50 59.7 60.8 4.50 6.17 6.24 59.614 11 66.3 56
65 75.3 76.6 4.50 7.90 8.02 75.184 11 82.0 65
80 88.0 89.5 4.85 10.10 10.30 87.884 11 95.0 71
100 113.1 115.0 5.40 14.40 14.70 113.030 11 122.0 83
125 138.5 140.8 5.40 17.80 18.30 138.430 11 147.0 92
150 163.9 166.5 5.40 21.20 21.80 163.830 11 174.0 92

Tolerances
Outside Diameter : As Per Above Table
Wall Thickness : -12.5%
Weight : Single Tube For Lot of 10 Tons
±10% ±7.5%

Testing
Leak Tightness Test 100% Hydrostatic At 50 Bar or Online Eddy Current Testing
For Tubes Upto & Including DN 25 For Tubes Above DN 25 & Upto DN 50
Bending Angle 90° Bending Angle 90°
Bend Test
Bending Radius 3 Times To The OD of Tube Bending Radius 3.5 Times To The OD of Tube
Weld Position 12 O' Clock & 3 O' Clock Weld Position 12 O' Clock & 3 O' Clock
For Tubes DN 65 & Above
Flattening Test
Flatten Up To 2/3 of Tube Dia Without Crack In Weld: Weld Position 12 O' Clock & 3 O'clock
Galvanizing Zinc Coating = 400 gm/sq m (minimum), Zinc Layer Thickness = 56 Microns

Mechanical Properties
Yield Strength 185 N/sq. mm (minimum)
310 To 540 N/sq.mm For Wall Thickness < 3 mm
Tensile Strength
290 To 510 N/sq.mm For Wall Thickness ³ 3 mm
% Elongation Thickness ³ 2 & < 3 mm ³ 3 & £ 40 mm
% Elongation 14 18
Raw Material As Per St 33.2 Conforming To DIN 17100

EN- 39 / BS: 1139 17