WELL CONTROL METHODS

WILD WELL CONTROL

 Well Control Methods

Learning Objectives

 You will learn well control circulating techniques  You will learn non-circulating well control
and proper responses to change in pressures. techniques:
 You will learn circulating well control techniques: • Volumetric
• Driller’s Method o Lubricate and Bleed
• Wait and Weight • Bullheading
• Concurrent
• Reverse circulation

WILD WELL CONTROL

 Well Control Methods

Overview

 The goal of all well control methods is to safely control the o Pressure is regulated with a choke.
well.
• Replacing the existing fluid with one that has sufficient
 Circulating well control methods are often referred to as weight to regain hydrostatic control.
“constant bottom hole” methods as they keep BHP equal to
FP preventing additional influx fluids.
 These methods provide for:
• Removal of kick fluids:
o Must keep BHP ≥ FP to prevent additional kicks.
o Must keep pump running at a constant speed.

WILD WELL CONTROL

 Well Control Methods

Overview

 Common circulating well control techniques are:  A well is very rarely killed by one circulation due
to inefficient fluid displacement in the annulus.
• Driller’s
• Wait and Weight
• Concurrent
 These all use the same procedures and only
differ when and if a kill weight fluid will be
circulated.

WILD WELL CONTROL

 Regulating Pressures

 Bottom hole and surface pressures may be a combination of several factors. These are:

• Formation pressure
• Hydrostatic pressure(s)
• Circulating Friction pressure
• Choke pressure

 Since FP, HP and circulating friction are fairly constant during the initial stages of well control, the
only way to change pressure is by choke manipulation.

WILD WELL CONTROL

 Regulating Pressures

 While shut in or circulating a kick with pump at a constant reduced circulating rate, pressure is
regulated by choke manipulation.
• To decrease pressures, open choke slightly:

- Increase choke orifice diameter.

 Bleeds off pressure while shut in.

 Reduces friction across choke while circulating.

• To increase pressures, reduce choke orifice size (close choke slightly).

- Decrease choke orifice diameter.

 Increases friction across choke while circulating.

WILD WELL CONTROL

 Regulating Pressures

 Choke adjustments must be made to maintain proper circulating pressure.

• If the circulating drillpipe/pump pressure gets too high, estimate the excess amount. Then use the choke
reduce or bleed off that amount. Monitor the casing pressure gauge whenever a pressure adjustment is
made.

• If circulating pressure is below the desired value, estimate the needed amount and monitoring the
casing pressure gauge, adjust to a more closed position until the adjustment pressure is made.

WILD WELL CONTROL

 Regulating Pressures

• Changes in pressure must be made only by using the gauge and not the choke position indicator. (The
indicator scale actually only shows the position of the choke and the direction it is moving. It does not
represent pressure changes.)

• If pressure on gauge (s) suddenly change, check pump rate and immediately return choke pressure to
last reliable value. Make a note of sequence of unregulated pressure changes.

WILD WELL CONTROL

 Regulating Pressures

 Choke adjustments depend on the frictional properties of different fluids that go

through it.
• Type of fluid.
• Rate of fluid flow.
• Fluid density.
 If these parameters are changed, a drastic change in choke pressure can
occur. Such is the case when gas begins to exit across the choke.
• The choke operator must anticipate this event and be ready to adjust the choke quickly to maintain the
back pressure held by the choke. Remember, if choke pressure suddenly decreases, pressure
throughout the well will also decrease and an additional influx may occur.
- Immediately return choke pressure to its last pressure value.
- Evaluate circulating pressure.
- Make additional changes if necessary.

WILD WELL CONTROL

 Choke Response – Liquid Following Gas

 The choke operator must also anticipate rapid increases in choke pressure. A
concern during well control is when liquid (fluid in use), following a gas kick
being circulated through the choke, enters the choke.
• Can cause rapid increase in pressure.

WILD WELL CONTROL

 Choke Response – Liquid Following Gas

 If the choke pressure is not immediately adjusted back to the prior value (just before this event),
the pressure increase may lead to lost circulation/formation breakdown.
• Subsea choke and kill lines require additional considerations, as both gas voiding the lines and liquid
following the gas must be taken into account.

WILD WELL CONTROL

 Choke Response – Lag/Transit Time

 Circulating (pump) and choke (casing) pressures are closely related through the “U-tube”.

 Any changes in circulating rates will affect the entire well.

• When a change in pressure occurs on one gauge, it will not be immediately reflected on the other
gauge.

WILD WELL CONTROL

 Choke Response – Lag/Transit Time

• The other gauge “lags” behind as the pressure change transits the U-tube.

- If a pressure adjustment is made, proper lag time must be allowed in order to get an accurate
reading before making unnecessary adjustments.

WILD WELL CONTROL

 Choke Response – Lag/Transit Time

• “Rule of thumb”: A lag time of two seconds per 1,000 feet of well length is typically required to transit a
pressure pulse in a drilling fluid.
- Obviously on deeper wells, lag times are longer than ones that are shallow.
- Compressibility of fluids (e.g., brine vs. gel muds) affect transit time.
• If additional adjustments are made before the pressure is allowed to transit the U-tube, inadequate or
unnecessary pressures can result.

WILD WELL CONTROL

 Choke Response – Lag/Transit Time

 Proper documentation is a very neglected aspect of well control.

• In times of potential confusion it is better to have written notes and pressures than to rely on memory.
• Good notes can show potential complications developing.
• Provides a record of events.
- These records can be of use on existing wells if problems/additional kicks occur.
- Can be of use for future wells.
- Very useful to help investigate and solve complications.

WILD WELL CONTROL

 Choke Response – Lag/Transit Time

 Record pressures, volumes, pit gains and choke adjustments. Jot notes
down on what’s going on.
 Be accurate!

WILD WELL CONTROL

 Commonalities for Circulating Methods

 When kick occurs, shut the well in!

• Check for leaks in BOP/manifolds, etc.

• Begin recording SIDPP, SICP, until pressures stabilize, record pit gain.

• Complete necessary worksheets.

• Depending on kill method, may begin weighting-up pits.

• When ready to circulate, hold choke (casing) pressure at its SICP value and SLOWLY bring pump up to
Kill Rate Speed.

WILD WELL CONTROL

 Commonalities for Circulating Methods

 Once pump is at kill speed, and casing pressure is at its SICP value, record
circulating (pump) pressure.
• This pressure is the Initial Circulating Pressure, ICP and must be held until when/if
kill fluid will be pumped.
• ICP = SIDPP + KRP
- Pressure above SIDPP is from pump, if choke pressure is correct.

WILD WELL CONTROL

 Simplifying the Initial Phase of Kill Ops

 Pre-operation meeting with all involved personnel. Everyone must know their responsibilities.
 Very good communication between pump and choke operator is necessary.
 The pump should be brought up to speed slowly or in gradual stages to avoid formation damage
or complications.
• On rigs with mechanical pumps, the pump can’t be brought to speed in slow stages because its slow
speed is idle and idle is the kill rate. The choke or a bypass should be opened, then the pump engaged.
Then, using the choke, adjust choke pressure to previous value.
 Casing pressure should be maintained at a constant pressure while bringing the pump to kill rate
speed. As soon as the pump is on line and running at proper kill rate speed, casing pressure
must be returned to its correct value.

WILD WELL CONTROL

 Simplifying the Initial Phase of Kill Ops

 ICP, which is shown on the circulating pressure gauge, is the pressure needed to circulate a well
at a given rate and prevent the well from flowing. ICP = SIDPP + KRP.
 If this value does not agree with calculated values a decision must be made.
• Were the shut in pressures correct, or could they be inaccurate due to gas migration?
• Are the gauges correct?
• Are the calculations correct?
• Were proper start up procedures used?
• Is the pump at the same efficiency as when kill rate pressures were taken?
 A decision must be made on what values to use, or shut it down, shut it in, reevaluate shut in
pressures, and try again.

WILD WELL CONTROL

 Simplifying the Initial Phase of Kill Ops

WILD WELL CONTROL

 Simplifying the Initial Phase of Kill Ops

Special Operational
Well Control
Considerations
Six Methods of Well
Control

Driller’s Wait and Reverse

Concurrent Volumetric Bullheading
Method Weight Circulation

Lubricate
and Bleed

WILD WELL CONTROL

 Simplifying the Initial Phase of Kill Ops

Methods of Well
Control

Driller’s Wait and Lubricate

Concurrent Volumetric Bullheading
Method Weight and Bleed

WILD WELL CONTROL

 Driller’s Method Action Sequence

Maintain CP constant and

turn on pump at lowest rate

1
Shut well back in
SLOWLY bring pump to
and verify kill
8 2 kill speed holding CP constant

From
Circulate kill fluid through
well maintaining FCP 7 Shut-in
well
3 Verify correct
circulating pressure
ICP

Maintain proper
pressure vs stks 6 4 Circulate Kick out maintaining ICP
ICP → FCP
5
Weight up pits
Prepare pressure chart
Switch to Kill Fluid

WILD WELL CONTROL

 The Driller’s Method

 Perhaps the most common method in use today.

 Good for gas kicks with high migration rates that may result in shut-in
problems.
 Also used to remove kicks that are swabbed in during a trip out of the hole.

 Used when no weighting material is necessary or available.

 Used when personnel and/or equipment is limited.

*More time to kill the well is needed in this method than other methods. It may cause
slightly higher pressure in the annulus than other methods (due to lack of additional HP
from Kill Fluid in initial circulation).

WILD WELL CONTROL

 The Driller’s Method

The Driller’s Method Procedure

Basic Circulation Technique - First Circulation – Removing Kick From Well:
1. Shut-in well after kick.
2. Record kick size and stabilized SIDPP and SICP.
3. ASAP start circulating original mud (fluid) by gradually bringing the pump up to the desired kill
rate while using the choke to maintain constant casing pressure at the shut-in value.
4. Pump pressure should be equivalent to calculated ICP. If not equivalent, investigate and
recalculate if necessary.
5. Maintaining pump pressure equal to ICP, kick/influx is circulated out of the well, adjusting
pressure with choke as required.

WILD WELL CONTROL

 The Driller’s Method

The Driller’s Method Procedure

After Kick Circulated Out – Killing The Well:
6. Continue to circulate from an isolated pit or slowly shut down the pump maintaining
pressure on the choke (casing) gauge equivalent to the original SIDPP.
• Avoid trapping pressure or allowing additional influx if shutting back in.
7. The active system should be weighted up to the pre-determined kill fluid density and
circulated in order to regain hydrostatic control.
8. If the well was shut in, start up pump procedures are again used.
9. It is advisable to calculate and use a pressure vs. stroke chart (ICP to FCP) to track
the kill fluid and changes in circulating pressures.
10. Circulate the kill fluid to the bit/end of string.

WILD WELL CONTROL

 The Driller’s Method

The Driller’s Method Procedure:

After Kick Circulated Out – Killing The Well:
11. Once kill fluid is at the bit/end of string, FCP should be realized.
• Circulating pressure should be equivalent to the calculated FCP.
12. Maintain constant FCP circulating pressure until the kill fluid completely fills the well.
• The gain in HP should necessitate slowly reducing choke pressure.
• Once the kill fluid reaches surface, the choke should have been fully opened.
13. Shut down pump and check for flow.
14. Close choke and check pressures.
15. If no pressure is noted, open choke (bleeding any trapped pressure), open BOP.

WILD WELL CONTROL

 Methods of Well Control

Methods of Well
Control

Driller’s Wait and Lubricate

Concurrent Volumetric Bullheading
Method Weight and Bleed

WILD WELL CONTROL

 Wait and Weight Method

 The Wait and Weight method kills the kick faster and keeps wellbore and surface pressures
lower than any other method.
 Requires good mixing facilities, full crews, and more supervision than most other methods.

 The first calculation that should be done in the Wait and Weight Method is kill fluid density.

 Fluid weight is increased before circulation begins, hence the name Wait and Weight.

 Start up procedures same as Driller’s method.3

WILD WELL CONTROL

 Wait and Weight Method

 Calculations required for:

• Kill fluid density

• ICP and FCP

• Volume/strokes/time surface to bit/end of string

• Pressure chart

• Volume/strokes/time bit to surface

• Total volume/strokes/time for complete circulation

• Pressure limitations

WILD WELL CONTROL

 Wait and Weight Method

1. Shut-in well after kick.

2. Record kick size and stabilized SIDPP and SICP, calculate kill fluid density.
3. Pits are weighted up as other calculations are performed.
4. If there are increases in shut-in pressure, the Volumetric Method should be used to bleed off
mud/fluid from the annulus to maintain constant stabilized drill pipe/tubing pressure.
5. Once pits are weighted, start circulating kill weight fluid by gradually bringing up the pump up
to the kill rate while using the choke to maintain constant casing pressure at the shut-in value.
Remember to hold pump rate constant.
6. Circulating pressure should be equivalent to (ICP) Initial Circulating Pressure. If not,
investigate and recalculate ICP if necessary.

WILD WELL CONTROL

 Wait and Weight Method

7. Follow pressure chart/graph as kill fluid is pumped down the string to bit/end of
string.
8. Once kill fluid is at the bit/end of string, FCP should be realized.
• Circulating pressure should be equivalent to the calculated FCP.

9. Maintain constant FCP circulating pressure until the kill fluid completely fills the well.
• The gain in HP should necessitate slowly reducing choke pressure.
• Once the kill fluid reaches surface the choke should have been fully opened.

10. Shut down pump and check for flow.

11. Close choke and check pressures.
12. If no pressure is noted, open choke (bleeding any trapped pressure), open BOP.

WILD WELL CONTROL

 Methods of Well Control

Methods of Well
Control

Driller’s Wait and Lubricate

Concurrent Volumetric Bullheading
Method Weight and Bleed

WILD WELL CONTROL

 Concurrent Method

 Sometimes referred to as the Circulate and Weight Method or Slow Weight-Up Method.
- It involves gradually weighting up fluid while circulating out the kick.
 Additional calculations are required when tracking different fluid weights in the string at irregular
intervals.
 * Sometimes, crew members are required to record concurrent method data even if this is not
the method intended to be used.

WILD WELL CONTROL

 Concurrent Method

The Concurrent Method Procedure:

1. Shut-in well after kick.
2. Record kick size and stabilized SIDPP and SICP.
3. ASAP start circulating original mud (fluid) by gradually bringing the pump up to the
desired kill rate while using the choke to maintain constant casing pressure at the
shut-in value.
• Pump pressure should be equivalent to calculated ICP. If not equivalent,
investigate and recalculate if necessary.
4. Mixing operations begin and pits are slowly weighted up and each unit of heavier fluid
reported.

WILD WELL CONTROL

 Concurrent Method

5. Each interval or unit of increased fluid density is then noted and recorded with the
pump stroke count at that time.
• The change in circulating pressure for the different density is calculated.
• Once this fluid reaches the bit/end of tubing, circulating pressure is adjusted with
the choke by that amount.
6. The kick is circulated out and the fluid in the well continues to be gradually
increased.
7. Once the kill fluid is consistent throughout the well, shut down pump and check for
flow.
8. Close choke, shut well in and check pressures.
9. If no pressure is noted, open choke (bleeding any trapped pressure), open BOP.

WILD WELL CONTROL

 Concurrent Method

Methods of Well
Control

Driller’s Wait and Lubricate

Concurrent Volumetric Bullheading
Method Weight and Bleed

WILD WELL CONTROL

 Volumetric Method of Well Control

 The volumetric method is a way of allowing controlled expansion of gas during

migration.
• It replaces volume with pressure (or vice versa) to maintain bottomhole pressure that is
equal to, or a little higher than BHP, and below the formation fracture pressure.
 With a swabbed in kick, the volumetric method can be used to bring influx to surface
and then replace the gas with fluid in order to return the well to normal hydrostatic
pressure.
 It is not used to weight up and kill the well.
• Used to control the well until a circulating method can be implemented.
• Can be used to regain HP if the existing fluid is adequate and gas is allowed to reach
surface.

WILD WELL CONTROL

 Volumetric Method of Well Control

 Situations where Volumetric Methods can be used:

• String is plugged.
• String is out of the hole.
• Pumps are not working.
• String is off bottom.
• During stripping or snubbing.
• A shut-in period or repairs to surface equipment.
• Tubing or packer leak causes casing pressure to develop on production or injection well.
• A washout in string prevents displacement of kick by one of the circulating methods.
• In subsea operations only 1 line should be used to prevent gas separation effects..

WILD WELL CONTROL

 Volumetric Method of Well Control

 If casing pressure does not increase 30 minutes after a kick is shut in, gas migration is
minimal. This means that the Volumetric Method need not be used. However, if casing
pressures continues to increase there is a need to initiate Volumetric techniques.
• Some basic scientific principles must be understood before using the Volumetric Method:
• Boyle’s Law – shows the pressure/volume relationship for gas. It states that if gas is allowed
to expand, pressure within the gas will decrease. This is the same concept used by the
Volumetric Method in that it allows gas to expand by bleeding off an estimated fluid volume
at surface, which results in decreasing of wellbore pressures.

Boyle’s Law
P1 V1 = P2 V2

WILD WELL CONTROL

 Volumetric Method of Well Control

 Single Bubble Theory – The biggest misconception in well control schools is that the
gas enters the well as a “single bubble”.
• In reality it is dispersed as pumping and observance of the kick is noted, then more “pure”
kick as the pumps are shut down and well is shut in.
• It may be many minutes before the kick is actually noted resulting in an annulus filled with
influx/regular fluid.
• So, in reality, a single large kick rarely occurs, and once the well is shut in, the pressures on
the casing shoe/weak zone have probably reached it’s maximum.
• This is not to say that MAASP should not be observed, just that it should be considered that
the maximum pressure should be based on the latest pressure test of the BOP or casing.

WILD WELL CONTROL

 Stripping/Moving Pipe and Volumetric Considerations

 A stripping pressure schedule must be created in order to control pressures during stripping
operations while gas is migrating, pipe is moving, and fluid is being bled off at choke.

WILD WELL CONTROL

 Lubricate & Bleed (Lubrication)

 The Lubricate & Bleed Method is used when kick fluid reaches the wellhead.

 It is considered a continuation of the Volumetric Method.

 Generally, workover operations more commonly use the Lubricate and Bleed technique because
circulating ports in the tubing are plugged, sanded tubing, or circulation is not possible.

WILD WELL CONTROL

 Lubricate & Bleed (Lubrication)

 In this method, fluid is pumped into the well on the annulus side.

 Enough time must be allowed for fluid to fall below gas.

 Volume must be precisely measured so hydrostatic pressure gain in the well can be calculated.

 This value increase will then be bled off at surface.

WILD WELL CONTROL

 Methods of Well Control

Methods of Well
Control

Driller’s Wait and Reverse

Concurrent Volumetric Bullheading
Method Weight Circulation

WILD WELL CONTROL

 Reverse Circulation

 Reverse circulation is the reversal of normal circulation or normal well kill pump direction.

 In reverse circulation, due to friction (APL, ECD) most of the circulating pump pressure is exerted
on the annulus.
 Standard start up procedures apply.

*Reverse circulation also has its advantages and disadvantages.

WILD WELL CONTROL

 Reverse Circulation

Advantages Of Reverse Disadvantages Of Reverse

Circulation Circulation
1. It is the quickest method of 1.Higher pressure is placed on
circulating something to the formation and casing.
surface. 2.Excessive pressure may cause
2. Gets the problem inside the fluid losses/casing and/or
strongest pipe from the formation failures.
beginning. 3.Not applicable for uses where
3. Generally, the annular fluid is plugging of circulating ports, bit
dense enough to maintain nozzles of string are possible.
control of the formation, which 4.Gas filled or multiple densities in
reduces fluid mixing and tubing may present problems
weighting requirements. establishing proper circulating
rates.

WILD WELL CONTROL

 Methods of Well Control

Methods of Well
Control

Driller’s Wait and Reverse

Concurrent Volumetric Bullheading
Method Weight Circulation

WILD WELL CONTROL

 Bullheading

 Bullheading, or deadheading, is often used as a method of killing wells in workover situations.

 Bullheading is only possible when there are no obstructions in the tubing and there can be
injection in the formation without exceeding pressure restraints.
 Bullheading involves pumping back well fluid into the reservoir, displacing the tubing or casing
with a good amount of kill fluid.

WILD WELL CONTROL

 Bullheading

 Complications can make bullheading difficult in certain situations:

- Sometimes, when bullheading down the tubing, pressure may have to be exerted on the casing
in order to prevent the tubing from collapsing. Both, tubing and casing burst/collapse pressures,
should be known and not exceeded.
- Formation fracture pressure may have to be exceeded due to low reservoir permeability
- Gas migration through the “kill fluid” can pose a problem. In this situation, viscosifiers should be
added to the kill fluid to minimize the effect of migration.

WILD WELL CONTROL

 Bullheading

Bullheading Procedure
1. Well is shut in and formation pressure is calculated. If bullheading down the tubing,
maximum pressures should be calculated.
2. Prepare a rough pressure chart of volume pumped versus maximum pressures at
surface. Friction and formation pressure must be overcome to achieve injection of the
liquid in the tubing back into the formation. If pressures or pump rate is too high,
damage to the formation may occur.
3. Once the pumped liquid reaches the formation, an increase in pump pressure may
occur. This is due to a non-native fluid injected to the formation.
4. Once the calculated amount of fluid is pumped, shut down, observe pressures. If no
pressure increase is observed, bleed off injection pressure and, again, observe. If no
pressure change is seen, the well should be dead. Proceed operations with caution.

WILD WELL CONTROL

 Bullheading

Formation
Injection
occurs

Kill fluid @
formation

WILD WELL CONTROL

 Bullheading

Special Operational Well Control Considerations

Slimhole Multi Lateral/Multi Completion

Air Drilling Mudcap

Communications Kicks Off Bottom

Stripping

Using Annular

Concentric Techniques MASP (MAASP)

Tubing Limitations UBD/PWD

WILD WELL CONTROL

 Air Drilling Well Control

 Air drilling allows a well to flow until the formation is producing at a sufficient rate or conditions
are no longer safe.
 Well killing techniques differ with different areas and different accepted practices. Some pump
water, some inject air. Some shut the well incompletely.
 Areas that perform air drilling techniques are usually limited on water and have formations that
do not produce high liquid or gas flow rates.

WILD WELL CONTROL

 Air Drilling Well Control

 Most kill techniques involve pumping water down the drillpipe to the bit. This water is pumped at
a high rate down the drillstring because:
• Extreme differences between weight of water being pumped and the formation gases in the annulus.
• Vacuuming – the well may “U-tube” faster than slower pump rates can keep up.

 The pump may be slowed down in order to avoid an abrupt increase in surge pressure on the
pump as the water reaches the end of the string.

WILD WELL CONTROL

 Air Drilling Well Control

 After pump rate is decided and fluid has reached the bit, different techniques may be used
depending on situation.
• Technique A:

- Continue pumping at high rate.

- When enough water hydrostatic has accumulated in the annulus, the formation flow stops and the
well is killed.

WILD WELL CONTROL

 Air Drilling Well Control

• Technique B:

- Circulating through the choke.

- This will cause more backpressure that may be enough to cease flow in the well.

- If not enough, a choke technique may be used.

The advantage of using backpressure is that holding backpressure through the choke
slows the expansion of gas.
This allows drops of water to fall back downhole, saving water that could be lost
when not using backpressure.

WILD WELL CONTROL

 Air Drilling Well Control

Choke Techniques
There are various choke techniques that can be used to maintain the
equivalent hydrostatic pressure of water in order to gain control of the well.
 Choke technique 1:
• When water rounds the bit, choke is closed enough to exert the water’s hydrostatic
as backpressure.
• Water circulates up the hole and backpressure is decreased by the estimated gain
in water hydrostatic.
• However, formation gases also exert hydrostatic pressure, so this must be noted in
order to stop the well from pressuring up higher than the equivalent weight of the
water used.

WILD WELL CONTROL

 Air Drilling Well Control

 Choke Technique 2:
• Pressure is not applied on choke until the water is believed to be at the casing
shoe.
• Equivalent hydrostatic from shoe to surface is held.
• Hydrostatic begins to gain above the shoe and the equivalent is bled from the
choke.
- However, the formation fracture or formation strength at the casing shoe is often unknown.
 This calls for a leak-off test, but it defeats the purpose of air drilling to water the
hole and perform the test.
 Therefore, this technique is not used in many areas.
 Additionally, the structural integrity of the formation or the strength of the bond
between the cement and casing is usually not known or tested.

WILD WELL CONTROL

 Mudcap Drilling

 Mudcap drilling is performed:

• When returns cannot be circulated back to surface.

• When annulus pressures at surface are nearing operational limits.
• If extreme drilling fluid loss is anticipated.
• If capacity of handling fluid at surface is exceeded.

 Mudcap drilling allows for drilling while managing extreme lost circulation in an overpressured
area.

As with most procedures, there are advantages and disadvantages to mudcap drilling.

WILD WELL CONTROL

 Mudcap Drilling

Advantages Of Mudcap Drilling Disadvantages Of Mudcap Drilling

1. Allows for drilling while managing 1. Increases required
extreme lost circulation in an training/qualification for personnel.
overpressured environment. 2. More logistical requirements and
Therefore, it saves time and money planning than conventional drilling.
from fighting lost circulation. 3. More potential for formation damage
2. Easier procedure than flow drilling. and more complex drilling/tripping
3. Reduces surface pressure on procedures.
annulus. 4. Higher pressure rotary drilling
4. Minimizes requirements for surface equipment is required.
fluid processing equipment. 5. Higher pump pressure is required,
5. Minimizes hydrocarbons, H2S at which may result in the need to
surface, which can be hazardous to modify the rig pump or change the
the environment. pump.
6. More potential for drillstring sticking
6. Not as much environmental planning
at point of injection by differential
needed as in PWD (Pressure While
pressure or cutting/packoff.
Drilling).
7. Because well is shut in at surface,
drill cutting and fluid samples are
unable to be obtained.

WILD WELL CONTROL

 Mudcap Drilling

 Pressured Mudcap Drilling Technique – Pressured mudcap drilling permits monitoring of annulus
pressure to show any changes downhole. A pressure ranging from 150 to 200 psi is usually held
on the choke. Changes in pressures indicate the potential of an influx in the well and/or formation
pressure changes.
 Non-pressured Mudcap Drilling Technique – no monitoring of annulus pressures. Used where
sub normal pressures are encountered.

WILD WELL CONTROL

 Mudcap Drilling

 Floating Mudcap Drilling Technique – A viscous heavy mud “cap” is used to prevent formation
flow is utilized. Usually used where a loss zone is encountered and the mudcap used to prevent
formation flow.

WILD WELL CONTROL

 Multi-Completion and Multilateral Considerations

 Well control is limited to the following when producing from multiple zones:

- Fluid barriers
- Mechanical barriers
- Live well intervention

WILD WELL CONTROL

 Slim Hole Considerations

 In slim holes, more than 90% of the hole length is drilled with bit diameters that are smaller than
7”.

 Concerns for slim hole include:

• High annular friction while pumping can cause fluid losses while circulating. Kill rate speed and
pressures must be at a rate slow enough to minimize annular friction.

• Since the diameter of the hole is smaller, there is a high potential for swabbing. Trip speed at a given
depth should be calculated and not exceeded.

WILD WELL CONTROL

 Slim Hole Considerations

The same techniques used to detect kicks are used in slimhole operations.

 However, since the hole is smaller, kicks must be detected on a smaller increase in flow, smaller
gain in pit or during the earlier stages.

 Prior to and during trips:

• Always use a trip log sheet.

• Calculate the pipe displacement accurately.

• Calculate the theoretical fill.

WILD WELL CONTROL

 Slim Hole Considerations

• Measure the trip tank accurately.

• Record the actual values.

• Compare against theoretical values.

• Consider “U-tubing” of the slug affecting several fill-ups.

• Consider a pumpout to no-swab potential depth.

 In addition to kick detection by rig crew, additional equipment can be used to monitor the well.
When used, alarms should be set.

WILD WELL CONTROL

 Slim Hole Considerations

 Consider using the following:

• Flow in
• Standpipe pressure
• Casing pressure
• Flow out
• Mud density in
• Mud density out
• Mud gas level
• Mud level in each tank
• Depth indicators
• MWD/LWD tools

WILD WELL CONTROL

 Communications

 Operations should not begin until each crew member has received, understands and can perform
his/her instructions and duties.

 Any and all changes in duties, from the normal duties, should be cleared, reported and recorded
by a supervisor.

 Well control is a team effort, so communication with all personnel involved is critical.

WILD WELL CONTROL

 Other Control Techniques

 The use of certain control techniques fluctuates on a case by case basis. More advanced
techniques besides the Driller’s, Wait and Weight, Concurrent and Volumetric methods include
are available.

 If conventional techniques do not regain control of the well the following may be considered:

• Dynamic and Momentum Kills.

*These techniques should only be used by experienced personnel with expertise in

these methods.

WILD WELL CONTROL

 Pressure Charts and Graphs

 A Circulating Pressure Graph shows what happens to circulating/drillpipe pressure as the new
heavier mud weight is being pumped down the string.
 A pressure chart shows strokes vs. what circulating pressure to hold at that point.

• Straightforward and used on most vertical wells for simplicity.

- Does not account for string geometry, friction per geometrical section and pressure drop across bit
nozzles.

WILD WELL CONTROL

 Pressure Charts and Graphs

 Column for:

• Strokes. Begin by clearing stroke counter to “0”.

- End with “strokes to bit/end of tubing”.
- To use a 10 step chart, divide “strokes to bit/end of tubing” by 10.
• Pressure. Begin with ICP and end with FCP.
- Use ICP – FCP divided by number of steps (e.g., 10).
- Start with ICP, and subtract the change of pressure per step.

WILD WELL CONTROL

 Pressure Charts and Graphs

Pressure Chart Modifications:

 High angle wells and also those using coiled tubing may have special considerations if the
Weight and Wait Method is used.
• Each section should be taken individually and the change in pressure charted/plotted.

• The pressure chart may not appear as a typical “straight line” and circulating pressure may actually
increase before Final Circulating Pressure is reached.

WILD WELL CONTROL

 Maximum Allowable Surface Pressure

 The maximum allowable surface pressure (MASP) must be calculated. The minimum of the
following is considered the pressure limitation:
- Casing Burst Pressure

- BOP Stack Limits

- Formation Fracture (pure liquid to weak zone)

 Crew members must be aware not to exceed value if based on casing burst or BOP limits.

WILD WELL CONTROL

 Maximum Allowable Surface Pressure

 Casing depth, present and kill fluid density, formation integrity, kick position, and imposed surface
pressures are factors that affect this pressure consideration.

WILD WELL CONTROL

 Tubing Pressure Limitations

 Internal Yield is the pressure value which, if applied within the tubular, will cause the pipe to
burst.
 Some operations must consider burst and collapse limitations of the tubing/string and care taken
not to exceed these values.

WILD WELL CONTROL

 Formation Pressure Considerations

 Any excess pressure exerted against a formation may cause an increase in time and costs of
working over to bring it back to production. Keep pressure to a minimum.

 As kill fluid flows down the production string, the amount of static surface pressure that may be
exerted before the damage decreases.

 Circulation friction rises as the kill fluid is pumped down the string, which increases surface
pressure and pressure in the tubing.
• These sudden increases in pressure may cause a burst in the tubing.

WILD WELL CONTROL

 UBD/PWD Equipment

 Mud gas separator

 Flow lines
 Gas flare line
 Separation tanks
 Pumps to move oil to frac or storage tanks and circulate fluid back to tanks for reuse.

* On land locations, lighting is essential at night, especially for the Derrickhand.

• UBD/PWD equipment may require additional lighting for safety purposes.
• Federal and state regulations require specific types of explosion proof lighting.

WILD WELL CONTROL

 UBD/PWD Equipment

 Rotating/Control Heads:
• Developed to control pressure while drilling underbalanced.
• Accidents occur while putting too much pressure on the rotating head rubber.
• There are different types of rotating and control head products.
• Low pressure tests of 200 to 300 psi are required and high pressure tests are optional.
 Kelly Types:
- Tri-Kelly.
- Hex-Kelly.
- Square-Kelly.

WILD WELL CONTROL

 UBD/PWD Equipment

 Stripper Rubbers:
• Used for air, gas, and water based fluid drilling.
• For oil based drilling fluids, polyurethane stripper rubbers are available.
 Pressure Testing:
• Testing procedures for the rotating head should follow manufacturer’s recommended procedures.
 Double Annulars:
• Before the improvement in higher working pressure of rotating heads, double annulars were used to
protect the crew.
• Having double annulars caused substructure restrictions on many rigs.

WILD WELL CONTROL

 UBD/PWD Equipment

 Special Considerations/High Angle-Horizontal and UBD/PWD Wells:

• The entire rig crew should be familiarized with certain things by the operator’s representative before
drilling the curve:
- Must know that the well may be shut in at any time, and many times, the situation is not as severe
as it looks.
- Surface equipment is tested before drilling the curve.
 The crew must have confidence in the equipment, so letting them see the test
results of equipment is a good idea.
- Must know all stations, duties, and responsibilities.
- Must know where all emergency numbers are posted.
- Must be prepared for dangerous situations in order to avoid panicking.
- In most safety operations, crew assignments in horizontal wells and vertical wells are similar.

WILD WELL CONTROL

 Well Kicks When the Pipe is Off Bottom

 Kicks that occur while tripping are usually due to a failure to detect a swabbing effect because
the hole is not taking the proper amount of fluid.
 Once an influx in the wellbore is noticed, the well should be shut in and controlled by stripping or
staging back to bottom, and pressures should be low.
 Generally, stripping back to bottom is one of the best options; however, pressures to hold versus
volumes gained can be complex with well geometry and various pipe sizes.

WILD WELL CONTROL

 Well Kicks When the Pipe is Off Bottom

 Hold the proper pressure.

• Pressure to hold = Original SICP + (Pressure Gradient (psi/ft)/ Annulus Capacity (bbls/ft)) for each
barrel of fluid gained as you strip back to bottom.
 Generally, once stripped back on bottom, the Driller’s Method is used because the result was a
swabbed kick where no additional fluid weight may be required.

WILD WELL CONTROL

 Stripping

 Stripping is the adding or removing of pipe when the well is pressured without allowing vertical
flow at the top of the well.

* Remember, if pressure is not watched carefully and adjusted according to the

displacement of pipe being stripped and gas expansion, the mistake may lead to
additional influx and/or extreme pressures in the well.
 If stripping, all personnel should be briefed and familiar with their responsibilities.

WILD WELL CONTROL

 Stripping

 Since stripping may lead to equipment failure, such as wearing of sealing elements, all activities
should be performed carefully.
 A float or inside BOP in the string is required whenever stripping in or out.
 To calculate if stripping operations will exert enough downward force to push pipe into the well
against pressures and preventer friction, use the following calculation:
Swt = (0.7854 x D2 x P) + F
Where:
Swt = estimated weight need to strip into hole, lbs
D = diameter of largest collar or tool joint in inches
P = annular pressure, psi
F = approximate pipe weight to slide through packer rubber (use a minimum of
2,000 lbs), lbs

WILD WELL CONTROL

 Stripping with the Annular Preventer

 For stripping purposes, the annular preventer is much easier and less time-consuming than
rams.
 There are some restrictions and special points that need to be checked prior to use of the
annular preventer:
- Consideration for stripping in the Hole with the Annular Preventer.
- Stripping Out of the Hole with the Annular Preventer.
- Stripping in the Hole using Pipe Rams.

WILD WELL CONTROL

 Concentric Techniques

 Small tubing, snubbing and coiled tubing units are specialized units that can strip and snub into
pressured wells. For our purposes, the differences are defined as:
• Stripping – movement of pipe in or out of well against pressure when pipe weight is greater than the
force to be overcome.

• Snubbing – forcing of pipe in or out of well against pressure that is great enough to eject the pipe.

WILD WELL CONTROL

 Concentric Techniques

 Seals from well pressures are provided by specialized stripper assemblies. These are usually
lubricators, stripper preventers or specialized BOPs.

WILD WELL CONTROL

 Well Control Methods

Learning Objectives

 You learned well control circulating • Concurrent

techniques and proper responses to • Reverse circulation
change in pressures.
 You learned non-circulating well control
 You learned circulating well control techniques:
techniques:
• Volumetric
• Driller’s Method • Bullheading
• Wait and Weight

WILD WELL CONTROL