Scribd
Upload
137 views12 pages

(Moving) Clown in A Barrel: Assembly Instructions

1) The document provides assembly instructions for a moving clown in a barrel model. It details 12 steps and includes diagrams showing how to cut and glue together over 30 individual parts to form the complete clown figure rolling inside two barrels. 2) Special tools like tweezers and a round bar are recommended to shape curved parts and handle small pieces. Glue should be applied in a thin even layer and parts fully formed before gluing to prevent distortion. 3) Young children should not handle tools like scissors or glue, so they should be kept out of reach during assembly. Following the numbered steps carefully will allow the clown figure inside the barrels to roll back and forth once completed.

Uploaded by

Eurico Rosato
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
137 views12 pages

(Moving) Clown in A Barrel: Assembly Instructions

1) The document provides assembly instructions for a moving clown in a barrel model. It details 12 steps and includes diagrams showing how to cut and glue together over 30 individual parts to form the complete clown figure rolling inside two barrels. 2) Special tools like tweezers and a round bar are recommended to shape curved parts and handle small pieces. Glue should be applied in a thin even layer and parts fully formed before gluing to prevent distortion. 3) Young children should not handle tools like scissors or glue, so they should be kept out of reach during assembly. Following the numbered steps carefully will allow the clown figure inside the barrels to roll back and forth once completed.

Uploaded by

Eurico Rosato
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 12

(Moving) Clown in a barrel : Assembly Instructions

Before starting assembly : Writing the number of each section on Indicates where sections should be glued together.
its back side before cutting out the sections is highly recommended. Indicates where to insert sections.
Do not glue the sections together.
ht t p : //w w w. c a n o n .c o m / c - pa r k / (* This way, you can be sure which section is which even after
cutting out the sections.) Indicates the order for assembling parts.

Round bar : Use to give parts a curved surface.


Be sure to build
this model carefully.
Tweezers : Useful in working with fine parts.

Caution : Spread glue in a thin,


even layer before gluing
surfaces together.

* Push and pull the lever on the


right. The barrels begin rolling
back and forth and merry
View of completed model acrobat of clowns starts.

Assembly Instructions : Twelve A4 sheets (No. 1 to No. 12)


* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.

*Hint: Trace along the folds with a ruler


and an exhausted pen (no ink) to get a sharper, easier fold.

Assembly Instructions
Glue
Mountain fold(dotted line)
The glue spot(colored dot)
Make a mountain fold.
shows where to apply the glue.
Valley fold(dashed and dotted line) Glue spot(Red dot)
Make a valley fold. Glue parts with the same number together.
Scissors line(solid line) Glue spot(Green dot)
Cut along the line. Glue within the same part.
Cut in line(solid line) Glue spot(Blue dot)
Cut along the line. Glue to the rear of the other part.

Scissors, set square, glue(We recommend stick glue), pencil, used


Tools and materials ballpoint pen, toothpicks, tweezers, (useful for handling small parts)

Before gluing, crease the paper along mountain fold and valley Make two sets.
Assembly tip fold lines and make sure rounded sections are nice and stiff.

Glue, scissors and other tools may be dangerous to young children


Caution so be sure to keep them out of the reach of young children.
(Moving) Clown in a barrel : Assembly Instructions

Firmly form the shape as


you glue to prevent distortion.

Parts 5 to 9

Prepare part 8 in the


same way.
(Moving) Clown in a barrel : Assembly Instructions

Before you glue the parts,


arch the barrel parts with
a round bar.

Parts 11 and 12
(Moving) Clown in a barrel : Assembly Instructions

Caution : Spread glue in a thin, even layer


before gluing surfaces together.
(Moving) Clown in a barrel : Assembly Instructions

Caution : Make sure the direction


of the barrel is correct.

Parts 11 and 12

Parts 5 to 9

Turn the entire body over and insert the part 1.


*It will be easier to work if you use 2 empty boxes on
Caution : the left and right as supports.
Make sure the direction The hexagonal
of Part 2 is correct before pasting margin
you glue it. comes to the front.
(Moving) Clown in a barrel : Assembly Instructions

Parts 22 and 23

Parts 22 to 24
(Moving) Clown in a barrel : Assembly Instructions

Parts 22 to 24

Parts 3 and 13

Parts 3 and 13
(Moving) Clown in a barrel : Assembly Instructions

Slowly push and pull the lever to check


the movement of the 2 barrels.

Parts 25 to 26

Glue the 8 corners of


the top sheet (Part 19).

Next, glue Part 31.


(Moving) Clown in a barrel : Assembly Instructions

When you assemble the base, work carefully


on a flat surface to prevent distortion.

First, put a lever through the hole in Part 28


and glue it, and then glue Part 29.
(Moving) Clown in a barrel : Assembly Instructions

Arm part Head part

Form the shape to prevent


distortion and glue both arms

Hand part Torso and leg part

Before you glue them, arch the torso


and leg parts with a round bar.
(Moving) Clown in a barrel : Assembly Instructions

Form the shape to prevent distortion and glue.


(Moving) Clown in a barrel : Assembly Instructions

Prepare parts 33,34,35 in the same way.

Make two sets.

Finished!

You might also like