Scribd
Upload
610 views

Fundamentals of Wireless Module 1 Answers

The document contains questions about wireless networking technologies including different wireless standards, devices, and design considerations. It covers topics such as wireless LAN components, modulation techniques, transmission speeds, and factors to consider for deployment.

Uploaded by

Ash_38
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
610 views

Fundamentals of Wireless Module 1 Answers

The document contains questions about wireless networking technologies including different wireless standards, devices, and design considerations. It covers topics such as wireless LAN components, modulation techniques, transmission speeds, and factors to consider for deployment.

Uploaded by

Ash_38
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

1

Which type of media is shown in the graphic?


coaxial

fiber optic

ScTP

STP

UTP

2 What is the maximum throughput that can be achieved by IEEE 802.11a compliant products?
10 Mbps

11 Mbps

54 Mbps

100 Mbps

3 Why is the direct sequence spread spectrum modulation technique ideal for data communications?
It spreads a transmission signal over a narrow range of radio frequencies so there is minimal loss.
It splits the radio signal into multiple smaller sub-signals that are transmitted at different frequencies to achieve high
throughput.
It is less susceptible to radio noise and creates little interference.

It reduces interference because it is only affected if two signals are transmitting at the same frequency at the same time.

Which device is represented by the symbol in the graphic?


wireless bridge

wireless AP

wireless switch

wireless VLAN

5 Which of the following modulation techniques offers more speed in a WLAN?


DSSS

FHSS

OFDM

OSDF
6 What is the purpose of the Cisco Aironet 350 Series Workgroup Bridge (WGB)?

to connect remote LANs over 40 km or 25 miles

to connect up to eight Ethernet-enabled clients to a WLAN

to extend the range of the wireless signal beyond 40 km or 25 miles

to connect two or more networks typically located in different buildings

Which type of media is shown in the graphic?


coaxial

fiber optic

ScTP

STP

UTP

8 When designing a WLAN, what must be completed before deployment decisions are made?
site design

site survey

site analysis

site inspection

site review

9 In a large WLAN, what is the function of multiple APs?


to allow mobile users to move throughout the WLAN

to provide direct user to user connection

to provide connection between multiple switches

to provide connection between multiple VLANs

10 Which WLAN requirement is met by the installation of redundant APs on separate frequencies?
ease of implementation

high availability

interoperability

manageability

profitability

scalability

11 At 2.4 GHz, which transmission speed can be delivered by IEEE 802.11b compliant devices?
up to 10 Mbps

up to 11 Mbps

up to 54 Mbps

up to 100 Mbps
12 Which types of transmission medium are available for use by WLANs? (Select two.)
fiber-optic

infrared light

UTP

radio frequencies

STP

13 Which AP feature makes firmware upgrades and configuration changes much easier?
nonvolatile CAM

removable radio transceiver

hot swappable IEEE 802.11 chips

nonvolatile FLASH ROM

14 Which technological and strategic developments assisted in the widespread acceptance of wireless technology? (Select
three.)
increase in cost of fiber-optic and copper installations

adoption of IEEE 802.11 standards

data rates commensurate with wired networks

increase in compliance regulations in Ethernet-based networks

increased security

15 Which IEEE standard contains the specifications for WLANs?


802.3

802.5

802.11

802.12

16 On Cisco wireless PC cards, which power mode provides the best connectivity option to the WLAN?
CAM

FastPSP

PSP

CAD

17 Why is microwave a less desirable solution than radio wave transmission in wireless bridge applications? (Select four.)
Equipment cost is typically high.

A government license is usually required.

Transmission rates are unreliable in any weather.

Rain, fog, or snow can significantly reduce performance.

The network is very difficult to maintain.

The network tends to be point-to-point.


18 What can be done to avoid interference in an 802.11 compliant WLAN?
change channels

use only omnidirectional antennas

deploy equipment from multiple vendors

install redundant WLAN equipment

use only free licensed frequency bands

19

Which device is represented by the symbol in the graphic?


wireless bridge

wireless AP

wireless switch

wireless VLAN

You might also like