LABORATORY 1

INTRODUCTION TO THE CIRCUIT LABORATORY

This is the first laboratory where you will deal with such matters as the course objectives,
syllabus, grading policy, laboratory rules and procedures, safety issues, preparation of
prelab and lab reports, the resistance color codes, the breadboard, and the Lab VIEW
equipment.

Objectives

• To enable students to gain skills in using basic electrical laboratory

equipment such as meters, power supplies, and oscilloscopes, which
skills they will need in subsequent electrical engineering laboratories
and in industry.

• To make the students aware of the limits of the operation of

components and equipment.

• To have the students gain skills in recording data and in reporting

experimental results--to effectively communicate what they have done
and observed.

• To give students self-confidence in electrical laboratories.

• To have the students become safety conscious in a laboratory

environment.

• To verify some of the concepts presented in the corequisite course,

either EEL 3111 or EEL 3003.

Syllabus

Although each teacher provides his/her own syllabus to the respective section(s), there
are some common features. All students perform the same set of experiments (in the
order listed in this manual) and all are graded by the same criteria.

Grades

There are 10 labs in total. Lab reports are due for five of them (labs 2, 5, 6, 7, 9) and
some of them have prelabs. We will also have a final project for which a lab report will
be due. The grades for the reports and lab sessions will be one out of A, B, C.
Prelab Reports

In this manual, the write up for each experiment starts with a brief review of the relevant
theory in the Introduction part. The instructor presents the underlying ideas in the class
before the experiment is performed. The prelab report will consist of answers to questions
posed in the introduction. The report will be due on the day the experiment will be
performed. It will be collected at the start of the class. Students not presenting the report
will be denied access to that experiment.

Lab Reports

These reports are written after the experiment is complete and they are due a week after.
Some general guidelines are given below. Your instructor may give you additional and
specific guidelines for preparing these reports.

Guidelines for Lab Reports

Several lab reports will be required during the semester. Typically, they are from four to
seven pages long, and are typed. Although the laboratory TA will explain what is
required for each lab report, in general each should contain the following sections:

Abstract: A brief summary of the experiment giving the purpose and

explaining what is going to be shown or proved, and how this is to be done.
The abstract should be fairly general.

Data: This should include a complete list of all the equipment used with
model and serial numbers; schematics of the circuits used; all calculated
and measured data in the form or tables or graphs; and the calculation of
percentage errors. Be sure to show a clear relation between the data and
the schematics. The data should be exactly what was obtained in the
experiment. Include units with the values. Additionally, carry only the
appropriate number of significant digits in your results.

Conclusions: Here, interpret the results (data). Compare the theoretical

results from the Introduction with the experimental results from the data,
and draw conclusions. For example, were the results different from what
was expected? Why were these results different? Specify the errors and
include possible sources of error. Answer any questions specified in the
lab sheet. Also, always explain why things happened the way they did.

Also,

Be objective and do not use phrases like “I was pleased . . .,” “The lab
went well . . .,”“It was good to know . . ., etc.
 Always give numerical results when applicable. Do not just say “the
results were as expected.” Specify the actual results, the expected results,
any errors, and explain them.

Be careful of the number of significant digits in the calculated results.

This number should not be greater than the least number of significant
digits in the data used for the calculations.

Be concise. A short direct lab report is more desirable than a long

rambling one.

Keep everything neat and label everything clearly. Start each section on a
new page. Write on only one side of each sheet.

Remember to number the equations and use figure numbers and table
numbers for any drawings or tables.

For reasons of his or her own, the laboratory TA may modify any of the above. Follow
the instructions of the laboratory TA.

Final Exam

Passing the course requires also passing the final exam. A student, who fails the final
exam, automatically fails the course, independent of other grades.

Safety

Although unlikely, it is possible to become injured in this laboratory. Emergency contacts

by phone are 911 and 395-0050, the latter is for the Emergency Room at Shands Hospital.
On some university phones it may be necessary to dial 9 first. Although there is no
phone in this laboratory, one is in EB288. Also, each office has a phone.

When working in any electrical laboratory, always keep electrical safety in mind.
Following are some safety rules that each student should be aware of before beginning a
laboratory experiment. Some of the rules do not apply to this laboratory, but to other
electrical laboratories.

1. Never work totally alone in the laboratory. Someone else,

and preferably the laboratory TA, should be present in the
case of an emergency.

2. Use only the equipment provided. Do not use other

equipment unless the laboratory TA approves the use.

3. Turn off the power before handling any wires.

 4. Never use damaged items, whether they are leads,
components, equipment, or any other item.

5. To decrease the chances of being shocked, wear dry shoes

and do not stand on metal or wet concrete. Also, do not
wear any metal or jewelry. Moreover, do not handle wires,
components, or equipment with wet hands.

6. In a laboratory in which soldering irons are used, keep an

attentive eye on a hot soldering iron. Also, place it in the
proper holder when not in use. Never leave a hot soldering
iron unattended.

7. Make no connection to the power supply until the very last

step. This practice will ensure that a student who is
handling leads will not be shocked. Also, the circuit being
built will not be harmed during construction.

8. Should someone become incapacitated because of electric

shock, no one should touch that person until the power is
turned off. Otherwise, the rescuer could also be shocked.
Call for emergency services as soon as possible since
resuscitation is likely if treatment is applied quickly. If
breathing has stopped, begin CPR immediately and
continue until qualified medical assistance has arrived.

9. If a piece of equipment is not working properly, attach a

note and report the problem to the lab TA. The
malfunction could possibly lead to a life-threatening
situation.

Electrical Shock:

A current of 100 to 200 mA causes ventricular fibrillation of the heart. This is an

irregular twitching of the wall of the ventricle of the heart, and is fatal. There is no
known remedy or resuscitation. Wet skin has a resistance of only 150 Ω and the hand-to-
foot internal body resistance is from 400 Ω to 600 Ω. In the case of, for example, 120 V
and a skin plus body resistance of 800 Ω, the result is a lethal current of 150 mA.

A current from 8 mA to 100 mA produces a painful shock, and perhaps also loss of
muscular control so that the victim cannot free him or herself from the cause of the shock.

Severe burns occur for a current greater than 200 mA. Also, the muscular contractions are
so severe that chest muscular reaction clamps the heart and stops it for the duration of the
shock. This reaction prevents ventricular fibrillation. Artificial respiration should be
administered immediately and in most cases the victim can be revived.
Resistance Color Codes

Unit of Resistance:

The SI unit of resistance is the Ohm, and the unit symbol is the capital Greek letter
omega Ω. Unit prefixes are used for writing convenience. For example, the prefixes k
and M represent 103 and 106 , respectively. Thus, 33 000 is written as 33 kΩ (33
kilohoms), and 1 200 000 as 1.2 MΩ (1.2 megohms).

Resistance Nominal Values and Tolerances:

Resistor manufacturers print resistance values on resistor casings either in numerical

form or in a color code. These values, though, are only nominal values. They are only
approximately equal to the actual resistances. The possible percentage variation of
resistance about the nominal value is called the tolerance. The popular carbon-
composition resistors have tolerances of 20, 10, and 5 percent, which means that the
actual resistances can vary from the nominal values by as much as ±20, ±10, and ±5
percent of the nominal values.

Color Code:

The most popular resistance color code has nominal resistance values and tolerances
indicated by the colors of either three or four bands around the resistor casing, as shown
in Fig. 1.1. (Sometimes there is a fifth band for failure rate. It will not be considered.)
The colors of the first and second bands correspond, respectively, to the first two digits of
the nominal resistance. The first digit, though, is never a zero. The color of the third
band, except for silver and gold, corresponds to the number of zeros that follow the first
two digits. A third band of gold corresponds to a multiplier of 10-1 , and one of silver to
10-2 . The fourth band indicates the tolerance and is either gold, silver, or is missing.
Gold corresponds to a tolerance of 5 percent, silver to 10 percent, and a missing band to
20 percent.

Fig. 1.1 - Reference: http://the12volt.com/resistors/index.html

The resistance color code is shown in Table 1.1. As can be determined from it, a resistor
with bands of red, yellow, orange, and gold is a 24 kΩ resistor of 5% tolerance. Also, a
resistor with bands of blue, gray, yellow, and silver is a 680 kΩ resistor of 10% tolerance.
And, a 1 Ω resistor of 20% tolerance has color bands of brown, black, gold, and missing.
Remember that the first digit is never zero, which means that the first color band is never
black.

Table 1.1 –Reference: http://the12volt.com/resistors/index.html

Breadboard Description

Most of the circuits built and tested in this laboratory will be assembled on a
“breadboard,”which looks like a piece of plastic with holes in it. Electrical components
(resistors, capacitors, wires, etc.) are inserted into the holes. What makes a breadboard
unique is that certain combinations of the holes are electrically connected with each other.
Since these connections are inside the plastic, they cannot be seen. Thus, a user must
know which holes are connected. Most breadboards have a similar pattern of
interconnections.

BREADBOARD CONNECTIONS:

The internal connections inside the breadboard run in both vertical and horizontal lines,
as shown in Fig. 1.2. It is important to remember that

1. The vertical connections are in groups of five.

2. The horizontal connections are in groups of twenty-five.

 3. No group of five (or twenty-five) is interconnected with
any other group of five (or twenty-five).

Fig. 1.2

Fig. 1.3

Therefore, separate components can be connected together at one point or node by

inserting the proper component(s) into the proper breadboard holes. The advantage of
using a breadboard is that relatively large circuits can be assembled neatly without having
a maze of interconnecting wires. Further, when connections must be made from the
assembled circuit to external equipment such as power supplies and meters, leads with
alligator clips on one or both ends can be used. The alligator clips are connected directly
to the circuit components. Preferably, a circuit should be assembled first and checked
before any external connections are made.

Note: Measurements of voltage, current, and resistance can be performed either by the
virtual bench digital multimeter (DMM) or by the hand- held multimeter. The connections
for each measurement are shown in the Appendix on the last two pages of the write up of
this experiment (Circuit Synthesis on a Breadboard). Note that for voltage measurements,
the meter is connected in parallel and for current measurements it is connected in series.
In order to avoid damage to components and instruments, it is essential that the
source be connected or turned on only when you have verified that the connections
have been correctly made.
 Introduction to the NI ELVIS Workspace

ELVIS is a combination of hardware and software elements comprising a complete

laboratory suite. A user interacts with the desktop proto-board via the control panel in
the workstation. Circuits are constructed on the proto-board. No external equipment is
needed; the desktop unit is capable of generating both AC and DC signals as well as
measuring the output of AC and DC circuits. Measurements can be made through ELVIS
or with external measuring devices. Manual adjustments can also be made on the unit by
disabling the control panel interface.

The control panel is also referred to as a soft front panel (from LabView). The soft panel
is capable of launching several instruments including an arbitrary waveform generator,
Bode analyzer, digital bus reader/writer, digital multimeter (DMM), dynamic signal
analyzer, function generator, impedance analyzer, oscilloscope, I-V analyzer, and
variable power supplies. Additional panels can be written through the LabView API to
interface with ELVIS. The use of these functions will be covered as the semester
progresses.

I. Launching the DMM Panel

a. Start NI ELVIS by going to the Windows Start menu and selecting Programs ->
National Insturments -> NI ELVIS 2.0-> NI ELVIS

b. You can launch the DMM by selecting Digital Multimeter from the menu. Once
active, you should have a new panel similar to the one depicted in Figure 1. The
DMM can be used for a variety of operations including measuring AC and DC
voltages and currents, resistance, capacitance, and inductance.

II. Voltage Measurements:

Measuring AC or DC voltage with the NI ELVIS DMM requires no external hardware

and can be done as follows.

a. For AC and DC voltage measurements, use the VOLTAGE HI and

VOLTAGE LO lines. These inputs are on the left-hand side of the proto-board,
shown in Figure 2, area 6.
b. The DMM runs in DC Voltage mode when launched. Select the VAC or VDC
button on the front panel of the DMM, depending on the signal to be measured,
and the measurement type changes to show the value of the signal. Auto scaling
should work best for most applications.
c. Connect signal leads. Remember that voltage is measured in PARALLEL to
the device in question.
d. Select the Single or Run option from the front panel controls. Selecting the
Single option displays an instantaneous value of the voltage. Selecting Run
provides continuos measurements of voltage.
III. Current Measurements

Measuring AC or DC voltage with the NI ELVIS DMM requires no external hardware

and can be done as follows.

a. For AC and DC current, resistor, capacitor, inductor, diode, and continuity

measurements, use the CURRENT HI and CURRENT LO lines. These inputs
are on the left- hand side of the proto-board, shown in Figure 2, area 6.
b. The DMM runs in DC Voltage mode when launched. Sele ct the VAC or VDC
button on the front panel of the DMM, depending on the signal to be measured,
and the measurement type changes to show the value of the signal. Auto scaling
should work best for most applications.
c. Connect signal leads. Remember that current is measured in SERIES with the
device in question.
d. Select the Single or Run option from the front panel controls. Selecting the
Single option displays an instantaneous value of the voltage. Selecting Run
provides continuous measurements of voltage.

Figure 1 –NI ELVIS DMM

 Figure 2 - Prototyping Board Parts Locator Diagram

IV. Launching the Variable Power Supply Panel

This is a top-level, stand-alone instrument that controls the variable DC supplies in the
NI ELVIS Benchtop Workstation. You can control the variable power supplies either
through the NI ELVIS - Variable Power Supplies SFP (Software Mode) or the
hardware controls on the benchtop workstation (Manual Mode).

a. Connect the Variable Power Supplies signals, SUPPLY+ and SUPPLY–, on the
NI ELVIS Prototyping Board to the location where they are needed. These are
independent power supplies, and both signals are referenced to the GROUND
signal.
b. The variable power supplies are active and output 0V when the panel is
launched. Select the desired voltage for each supply in the Voltage Adjust
control, and the output updates accordingly.
V. Exercise

This part of the experiment will demonstrate LabVIEW’s ability in making both voltage
and current measurements.

Figure 3.

1. Set up the circuit in Figure 3. Do not forget to ground your circuit.

2. Measure the voltage across all the branches, including V1 , in Figure 3 using the
procedure described in step II.
3. Measure all branch currents in Figure 3 using the procedure described in step III.
4. Measure the above voltages by also using the hand- held mulitimeter. Compare
these values to those obtained in step 2.
5. Measure the above branch currents by also using the hand- held multimeter.
Compare these values to those obtained in step 3.
6. Compare these results with theoretical values given to you by the instructor. Make
sure to include percent error calculations as well.

| your result - accepted value | * 100

accepted value
 CIRCUIT SYNTHESIS ON A BREADBOARD

ELEMENTS AND CONNECTIONS

VOLTAGE SOURCE

RED

From Voltage

Source

BLACK GND

OHMMETER (RESISTANCE MEASUREMENT)

RED
+

OHM To Multimeter
R
METER

-
BLACK
GND

AMMETER (CURRENT MEASUREMENT)

RED

I I
CURRENT V
V To Multimeter
METER

BLACK
GND
VOLTMETER (VOLTAGE MEASUREMENT)

V V

+ Vr - + Vr -

RED

VOLTAGE
To Multimeter
METER
BLACK

EXAMPLE

RED
V
BLACK

GND GND

From
Voltage
Source