Table 5: 'UNILOK' High Strength Structural Washers - Dimensions

Bolt Size M16 M20 M22 M24 M27 M30 M36

Min. 18.00 22.00 24.00 26.00 30.00 33.00 39.00
d
Max. 18.43 22.52 24.52 26.52 30.52 33.62 39.62
Max. 34.00 42.00 44.00 50.00 56.00 60.00 72.00
D
Min. 32.40 40.40 42.40 48.40 54.10 58.10 70.10
Max. 4.60 4.60 4.60 4.60 4.60 4.60 4.60
H
Min. 3.10 3.10 3.40 3.40 3.40 3.40 3.40
Weight
Kg/1000pcs 20.3 31.3 33.2 44.7 54.8 61.4 89.7

Table 6: Mechanical Properties of H.S.S. Bolts

Property Class 8.8 Property Class 10.9
Stress
Thread Ultimate Proof Load Ultimate Proof Load
Area Hardness Hardness
Size Load (Min) (Min) Load (Min) (Min)
2
mm Newtons Newtons HRC Newtons Newtons HRC
M16 157 125600 91060 22-32 163280 130310
M20 245 203350 147000 254800 203350
(M22) 303 251490 181800 315120 251490
M24 353 292990 211800 367120 292990 32-39
23-34
(M27) 459 380970 275400 477360 380970
M30 561 465630 336600 583440 465630
M36 817 678110 490200 849680 678110

Table 7: Mechanical Properties of H.S.S. Nuts

Property Class 8 Property Class 10
Thread Size Proof Load Proof Load
Hardness Hardness
Newtons Newtons
M16 168900 195500
M20 263400 305000
(M22) 325700 HRB89 377200 HRC 26
M24 379500 To 439500 to
(M27) 493400 HRC 38 571500 HRC 38
M30 603100 698400
M36 878300 1017200

ASSEMBLY paint or any other foreign material or placed in position.

Calculation of Bolt length : any defect. A clean, as rolled surface Driving of bolts should not be
The length of bolt required to be used with light mill scale is acceptable. permitted as it will damage the
in the assembly will depend on the All bolts, nuts and washers should be threads.
Grip Length (Clamping Length). Table identified as being the correct type Each bolt and nut should be
4 gives range of Grip Lengths for H.S.S. Fasteners while drawing from assembled with flat washer under the
individual Bolt Lengths. In deciding the stores. The holes will be lined up with nut or bolt head, whichever is to be
ranges, allowances have been made sufficient drift pins to maintain the rotated during tightening, preferably
for the thickness of nut, one flat round dimensions and plumbness of the tightening will be done by nut rotation.
washer and sufficient thread protrusion structure until bolts in the remaining Taper washers are used under nuts or
beyond nut. Adequate allowances holes have been fully tightened - well bolt heads where I angular seatings are
should be made for additional aligned holes will permit bolts to be necessary.
washers or taper washers, if used. freely

Holes in Members:
All holes should preferably be drilled,
burrs should be removed. Nominal
hole diameters are given in Table 8.

Operation:
All contact sufaces should be free of
oil, dirt, loose scales, rust, burrs,