SUBSTITUTE MATERIAL (JIS, BS, DIN ) FOR ASTM SPECIFICATION

CONTENTS

Section

1. Scope
2. Basis
3. Additional Requirements
4. Table
5. Table 1, Plates
6. Table 2, Pipes
7. Table 3, Tubes
8. Table 4, Forging
9. Table 5, Castings
10. Table 6, Bolts and Nuts
11. Table 7, Bars and Shapes
12 Table 8, Piping Fittings
13. Table 9, Nonferrous Materials

1. SCOPE
This specification lists the Japanese Standard (JIS, JPI),British Standard (BS), and Deutshe Industrie Normen (DIN) substitutes for ASTM Specifications
relating to materials for plates, pipes, tubes, forging, castings, bolts and nuts, bars and shapes, piping fittings, and nonferrous materials, in general use.

2. BASIS
These substitutes are not necessarily identical to the ASTM Specifications, but are equal in terms of alloy content and have a nearly equal or higher ultimate
tensile strength; exceptions to this are underlined.

3. ADDITIONAL REQUIREMENTS
The requirements of the ASTM Specifications not covered by the substitute specifications are noted in the Tables, with footnotes given on Section 4.

4. TABLE
Substitute materials are shown in the following Tables 1 to 9.
 STANDARD SPECIFICATION

Table 1 PLATE
ASTM JIS BS DIN
A-36
Structural Steel
G 3101 SS400 4360 Gr 40A (1) 17100 St44-2
G 3105 SM400A 4360 Gr 438 (1) 17100 St44-3

A-131
Structural Steel for Ships
Gr A G 3106 SM400A 4360-40B 17100 St44-3
Gr B G 3106 SM400B 4360-40B ---
Gr CS G 3105 SM400CN 4360-40E ---
Gr D G 3105 SM400C (2) 4360-40E ---
Gr E G 3105 SM40OCN 4360-40E ---

A-167
Stainless arid Heat-Resisting
Chromium,-Nickel Steel Plate,
Sheet, and Strip
Type 302 G 4304 SUS302 (3) --- 17440/1 X10CrNiS189
Type 304 G 4304 SUS304 (3) 1449-304S31 17440/1 X5CrNi1810
1501-304S15
Type 304L G 4304 SUS304L (3) 1501-304S12 17440/1 X2CrNi1911
1449-304S11
Type 310S G 4304 SUS310S (3) 1501-310S24 ---
1449-310S24 ---
Type 316 G 4304 SUS316 (3) 1501-316S16 17440/1 X5CrNiMo17122
1449-316S31
Type 316L G 4304 SUS316L (3) 1501-316S12 17440/1 X2CrNiMo17132
1449-316S11
Type 321 G 4304 SUS321 (3) 1501-321S12 17440/1 X6CrNiTi1810
1449-321S31
Type 347 G 4304 SUS347 (3) 1501-347S17 17440/1 X6CrNiNb1810
1449-347S31

Note (1): Specify mechanical properties, test and inspection in accordance with ASTM.
Note (2): Plates over 1-3/8 Inches (35 m-n) in thickness shall be normalized.
Note (3): For cold rolled sheet and strip, use corresponding SUS-CP and SUS-CS steels, according to JIS G 4305 and G 4307, respectively.
 STANDARD SPECIFICATION

ASTM JIS BS DIN

A-176
Stainless and Heat Resisting
Chromium Steel Plate, Sheet,
And Strip
Type 403 G 4304 SUS403 (1) 14-09-403 S17 S2) ---
1501-403 S17 l2) ---
Type 405 G 4304 SUS405 (1) 1449-405 S17 17440/1 X6CrAl13
1501-405 S17 ---
Type 410 G 4304 SUS410 (1) 1449-410 S21 17440/1 X10Cr13
Type 4105 G 4304 SUS410S (1) --- 17440/1 X6Cr13

A-203
Pressure Vessel Plates,
Alloy Steel, Nickel
Gr A G 3127 SL2N255 --- ---
Gr D G 3127 SL3N255 1501-503 ---
Gr E G 3127 SL3N275 --- 17280 10Ni14
Gr F G 3127 SL3N440 --- ---
A-204
Pressure Vessel Plates,
Alloy Steel, Molybdenum
Gr A G 3103 S64SOM --- SEL 16 Mo5
17155 15 Mo3
Gr B G 3103 SB48M --- SEL 16 Mo5
Gr C --- --- ---

A-240
Heat-Resisting Chromium and
Chromium-Nickel Stainless
Steel Plate, Sheet, and Strip
for Pressure Vessels
Type 304 G 4304 SUS304 (1) 1501-304S15 17440/1 X5CrNi1810
Type 304H --- 1501-304S49 ---
Type 304L G 4304 SUS304L (1) 1501-304S12 17440/1 X2CrNi1911
Type 316 G 4304 SUS316 (1) 1501-316S16 17440/1
X5CrNiMo17122
Type 316H --- 1501-316S49 ---
Type 316L G 4304 SUS316L (1) 1501-316S12 17440/1
X2CrNiMo17132
Type 317 G 4304 SUS317 (1)
Type 317L G 4304 SUS317L (1) --- 17440/1
X2CrHiMo18164

Note (1): For cold rolled sheet and strip, use corresponding SUS-CP and SUS-CS steels, according to JIS G 4305 and G4307,
respectively.
Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or
specify minimum tensile and yield strengths per ASTM.
 STANDARD SPECIFICATION

ASTM JIS BS DIN

Type 321 G 4304 SUS321 (1) 1501-321S12 17440/1 X6CrNiTi1810
Type 321H --- 1501-321S49 ---
Type 347 G 4304 SUS347 (1) 1501-3-07S17 17440/1 X6CrNiNb1810
Type 347H --- 1501-347S49 ---
Type 405 G 4304 SUS405 (1) 1501-405S17 17440/1 X6CrAl13
Type 410 G 4304 SUS410 (1) --- 17440/1 X10Cr13
Type 410S G 4304 SUS410S (1) --- 17440/1 X6Cr13
Type 430 G 4304 SUS430 (1) --- 17440/1 X6Cr17
A-263
Corrosion-Resisting
Chromium Steel-Clad
Plate, Sheet, and
Strip
G 3601 (2) --- 17440/1
A-264
Stainless Chromic-Nickel Steel-
Clad Plate, Sheet, and Strip
G 3601 (2) 3740 (2) 17440/1
A-265
Nickel and Nickel-Base
Alloy-Clad Steel Plate
G 3602 (2) --- 17743 NiCu30Fe
A-283
Low and Intermediate Tensile
Strength Carbon Steel Plates,
Shapes, and Bars
Gr A G 3101 SS330 4360 Gr 40A/B/C 17100 St33
Gr B G 3101 55330 4360 Gr 40A/B/C 17100 St33
Gr C G 3101 SS400 4360 Gr 40D 17100 St44-2
Gr D G 3101 SS400 4360 Gr 43A/B/C/D 17100 St44-2

Note (1): For cold rolled sheet and strip, use corresponding SUS-CP and SUS-CS steels, according to JIS G 4305 and G4307,
respectively.
Note (2): Specify mechanical properties, test and inspection in accordance with ASTM.
 STANDARD SPECIFICATION

ASTM JIS BS DIN

A-285
Pressure Vessel Plates,
Carbon Steel, Low-and
Intermediate-Tensile
Strength
Gr A & B --- 1501-151 Gr 360 17155 H I
Gr C G 3103 S8410 1501-151 Gr 430 17155 H II

A-299
Pressure Vessel Plates, Carbon
Steel, Manganese Silicon

G 3115 SPV355 --- 17102 StE355

A-302
Pressure Vessel Plates, Alloy Steel
Manganese-Molybderalm and
Manganese-Holybdenum-
Nickel
Gr A G 3119 SBV1A --- ---
Gr B G 3119 SBV1B --- ---
Gr C G 3119 SBV2 --- ---
Gr D G 3119 SBV3 --- ---

A-387
Pressure Vessel Plates, Alloy Steel
Chromium-Molybdenum
Gr 2 Class 1 G 4109 SCMV1 --- ---
Gr 11 Class 1 G 4109 SCMV3 1501-621 ---
Class 2 G 4109 SCMV3 1501-621
Gr 12 Class 1 G 4109 SCMV2 1501-620 17155 13CrMo44
Class 2 G 4109 SCMV2 1501-620 ---
Gr 21 Class 1 G 4109 SCMV5 --- ---
Gr 22 Class 1 G 4109 SCMV4 1501-622 Gr 515 17155 10CrMo910
Class 2 G 4109 SCMV4 1501-622 Gr 515 ---
Gr 5 Class 1 G 4109 SCMV6 --- SEW590 12CrMo195
Class 2 G 4109 SCMV6 --- ---
Gr 9 Class 1 --- --- ---
Class 2 --- --- ---

ASTM JIS BS DIN

A-442
Pressure Vessel Plates, Carbon
Steel, Improved Transition
Properties
Gr 55 --- 1501-151 Gr 400 SEW 680 TTSt41N
1501-161 Gr 400
1501-224 Gr 400
Gr 60 G 3115 SPV235 1501-151 Gr 430 ---
1501-161 Gr 430
1501-224 Gr 430

A-516 -
Pressure Vessel Plates, Carbon
Steel, for Moderate and Lower
Temperature Service

Gr 55 --- 1501-161 Gr 400 17155 H I

1501-224 Gr 400
Gr 60 G 3118 SGV410 1501-161 Gr 430 17155 H II
1501-224 Gr 430
Gr 65 G 3118 SGV450 1501-224 Gr 460 17155 17Mn4
Gr 70 G 3118 SGV480 1501-224 Gr 490 17155 19Mn6

Note (1): Recognize lacer minimum tensile or yield strengths of the underlined substitute materials in design consideration,
or specify minimum tensile and yield strengths per ASTM.
 STANDARD SPECIFICATION
Note (1): Recognize loner minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and
yield strengths per ASTM.
Note (2): Specify mechanical properties, test and inspection in accordance with ASTM.

ASTM JIS BS DIN

A-533 I
Pressure Vessel Plates,Alloy Steel
Quenched and Tempered
Manganese- Molybdenum and
Manganese- Molybdenum Nickel

Type A Class 1 G 3120 SQV1A --- ---

Class 2 G 3120 SQV1B --- ---
Type B Class 1 G 3120 SQV2A --- ---
Class 2 G 3120 SQV2B --- ---
Type C Class 1 G 3120 SQV3A --- ---
Class 2 G 3120 SQV3B --- ---

A-537
Pressure Vessel Plates, Heat-
Treated, Carbon-Manganese-
Silicon Steel
Class 1 G 3115 SPV355N 1501-224 Gr 490 (1) 17155 19Mn6
17102 StE355
Class 2 G 3115 SPV450Q --- ---

A-570
Steel, Sheet and Strip, Carbon,
Hot-Rolled, Structural Quality.

Gr 30 G 3101 SS330 1449-HR 34/20 (1) 17100 St33

Gr 33 G 3101 SS400 1449-HR 37/23 17100 St44-2
Gr 36 G 3101 SS400 1449-KR 37/23 17100 St44-2
Gr 40 G 3101 SS400(1) 1449-HR 43/25 17100 St44-2
Gr 45 G 3101 SS490 1449-HR 43/25 (1) 17100 St52-3
Gr 50 G 3101 SS490(1) 1449-HR 50/35 17100 St52-3

A-611
Steel, Sheet, Carbon, Cold-Rolled
Structural Quality

Gr B G 3141 SPCC (2) --- ---

Gr C G 3141 SPCC (2) --- 1623.1 St12
Gr D G 3141 SPCC (2) --- ---
STANDARD SPECIFICATION
Note (1): Specify Impact Test requirement per ASTM.

Note (2): Recognize lager minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and
yield strengths per ASTM.

ASTM JIS BS DIN

A-652
Pressure Vessel Plates, Carbon
Manganese, for Moderate and
Lower Temperature Service

Gr A G 3126 SLA235 (1) --- ---

Gr B G 3126 SLA325 (1)(2) --- 17102 EStE315
Gr C G 3126 SLA360 (1) --- 17102 EStE355
STANDARD SPECIFICATION
Table 2 PIPE
Note (1): Specify carbon, manganese, or silicon contents to accordance with ASTM.

Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and
yield strengths per ASTM.

ASTM JIS BS DIN

A-53
Pipe, Steel, Black and Hot-Dipped
Zinc-Coated Welded and Seamless

Type F G 3452 SGP 1387 1615 St33

Gr A G 3454 STPG370 3601 ERW360 1626 St37.0
S360 1629 St37.0
Gr B G 3454 STPG410 3601 ERW410 1626 St44.0
S410 1629 St44.0

A-106
Seamless Carbon Steel Pipe for
High-Temperature Service

Gr A G 3456 STPT370 3602 HFS360 17175 St35.8

3602 CFS360
Gr B G 3.455 STPT410 3602 HFS410 17175 St45.8
3602 CFS410
Gr C G 3456 STPT480 3602 HFS460 17175 St45.8
3602 CFS460
A-134
Pipe, Steel, Electric-Fusion (Arc)-
Welded (Size NPS 16 and over)

Material
A 283 Gr A – D G 3457 STPY400 3602 SAW410 ---
3601 SAW410
A 285 Gr A – C G 3457 STPY400(1) --- --
A 570 Gr 30 – 40 G 3457 STPY400 (1)(2) --- --
A 36 G 3457 STPY400 3602 SAW410 --
3601 SAW410
STANDARD SPECIFICATION
Note (1): Specify electric resistance-welding.

Note (2): Recognize loner minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum
tensile and yield strengths per ASTM.
Note (3): Specify carbon, manganese, or silicon contents in accordance with ASTM.

ASTM JIS BS DIN

A-135
Electric-Resistance-Welded
Steel Pipe
Gr A G 3454 STPG370 (1) 3601 ERW360 1626 St37.0
Gr B G 3454 STPG410 (1) 3601 ERW410 1626 St44.0 .

A-139
Electric-Fusion (Arc)-Welded
Steel Pipe (NPS 4 and over)

Gr A – E G 3457 STPY400 (2)(3) 3602 SAW410 (2) ---

3601 SAW410 (2)
A-211
Spiral-Welded Steel or Iron Pipe

A 570 Gr 30-45 G 357 STPY400 (2)(3) 3602 SAW 410 (2) ---
3601 SAW 410 (2)
A 570 Gr 50 --- 3502 SAW 460 (2)

A-312
Seamless and Welded Austenitic
Stainless Steel Pipe

TP 304 (18Cr-8Ni) G 3459 SUS304TP 3605-304S18,S25 17457/58 X5CrNi1810

TP 304H (18Cr-8Ni) G 3459 SUS304HTP 3605-304S59 ---
TP 304L (18Cr-8Ni) G 3459 SUS304LTP 3605-304S14,S22 17457/58 X2CrNi1911
TP 309 (23Cr-12Ni) G 3459 SUS309STP --- ---
TP 310 (25Cr-20Ni) G 3459 SUS310STP --- ---
TP 316 (16Cr-12Ni-21Mo) G 3459 SUS316TP 3605-316S18,S26 17457/58
X5CrNiMo17122
TP 316H (16Cr-12Ni-2Mo) G 3459 SUS316HTP 3605-316S59 17459E X6CrNiMo1713
TP 316L (16Cr-12Ni-2Mo) G 3459 SUS316LTP 3605-316S14,S22 17457/58
X2CrNiMo17132
TP 321 (18Cr-10Ni-Ti) G 3459 SUS321TP 3605-321S18,S22 17457/58 X6CrNiTi1810
TP 321H (l8Cr-12Ni-Ti) G 3459 SUS321HTP 3605-321S59 SEW470 X12CrNiTi189
TP 347 (18Cr-10Ni-Cb) G 3459 SUS347TP 3605-347S18,S17 17457/58
X6CrNiNb1810
TP 347H (18Cr-10Ni-Cb) G 3459 SUS347H TP 3605-347S59 ---
STANDARD SPECIFICATION
Note (1):Recognize Lower minimum tensile or yield strengths of the underlined substitute materials in design consideration or specify minimum tensile and
yield strengths per ASTM.
Note (2):VdTuv-Werkstoftblatt

ASTM JIS BS DIN

A-333
Seamless and Welded Steel Pipe
for Low-Temperature Service

Gr 1 G 3460 STPL380 3603-CFS410 LT50 17173 TTSt35N

3603-HFS410 LT50 17174 TTSt35N
3603-ERW410 LT50
3603-CEW410 LT50
Gr 3 (3-1/2Ni) G 3460 STPL450 3603-HFS503 LT100 17173 l0Ni14
3603-CFS503 LT100
Gr 6 --- 3603-CFS410 LT50 SEW680 TTSt45N
3603-HFS410 LT50
3603-ERW410 LT50
3603-CEW410 LT50
Gr 8 (9Ni) G 3460 STPL690 3603-HFS509 LT196 17173 X8Ni9
3603-CFS509 LT196

A-335
Seamless Ferritic Alloy-Steel Pipe
for High-Temperature Service

Gr P1 (C-1/2Mo) G 3458 STPA12 --- 17175 15Mo5

Gr P5 (5Cr-1/2Mo) G 3458 STPA25 3604 CFS625 (1) Wbl 007/2 12CrMo195
(2)
3604 HFS625 (1)
Gr P9 (9Cr-1Mo) G 3458 STPA26 3604-CFS629-470 (1) Wbl 109 X12CrMo91 (2)

Gr P11 (1-1/4Cr-1/2Mo) G 3458 STPA23 3604 CF5621 17175 13CrMo44

3604 HFS621
Gr P12 (1Cr-1/2Mo) G 3458 STPA22 3604 CFS620-460 (1) 17175 13CrMo44
3604 HFS620-460 (1)
Gr P22 (2-1/4Cr-1Mo) G 3458 STPA24 3604 CFS622 17175 l0CrMo910
3604 HFS622
STANDARD SPECIFICATION
Note (1): Specify seamless.

ASTM JIS BS DIN

A-358
Electric-Fusion-welded Austenitic
Chromium-Nickel Alloy Steel Pipe
For High-Temperature Service

Grade Material
304 A240, Type 304 G 3468 SUS304TPY 3605 LWHT 304S18 17457 X5CrNi1810
304L A240, Type 304L G 3468 SUS304LTPY 3605 LWHT 304S14 17457 X2CrNi1911
316 A240, Type 316 G 3468 SUS316TPY 3505 LWHT 316S18 17457 X5CrNiMo17122
316L A240, Type 316L G 3468 SUS316LTPY 3605 LWHT 316S14 17457 X2CrNiMo17132
321 A240, Type 321 G 3468 SUS321TPY 3605 LWHT 321S18 17457 X6CrNiTi1810
347 A240, Type 347 G 3468 SUS347TPY 3605 LWHT 347S18 17457 X6CrNiNb1810

A-376
Seamless Austenitic Steel Pipe for
High-Temperature Central-Station
Service
TP 304 (18Cr-8Ni) G 3459 SUS304TP (1) 3605-304S18 17459 X6CrNi1811
E
TP 304H (18Cr-8Ni) G 3459 SUS304HTP (1) 3605-304S59 ---
TP 316 (16Cr-12Ni-2Mo) G 3459 SUS316TP (1) 3605-316S18 17458 X5CrNiMo17122
TP 316H (16Cr-12Ni-2Mo) G 3459 SUS316HTP (1) 3605-316S59 17459 X6CrNiMo1713
E
TP 321 (18Cr-10Ni-Ti) G 3459 SUS321TP (1) 3605-321S18 17458 X6CrNiTi810
TP 321H (18Cr-10Ni-Ti) G 3459 SUS321HTP (1) 3605-321S59 ---
TP 347 (18Cr-10Ni-Cb) G 3459 SUS347TP (1) 3605-347S18 17458 X6CrNiNb1810
TP 347H (18Cr-10Ni-Cb) G 3459 SUS347HTP (1) 3605-347S59 ---

A-409
Welded Large Diameter Austenitic
Steel Pipe for Corrosive or High
Temperature Service

TP 304 (18Cr-8Ni) G 3468 SUS304TPY --- 17457 X5CrNi810

TP 304L G 3463 SUS304LTPY --- 17457 X2CrNi1911
TP 316 (16Cr-12Ni-2Mo) G 3468 SUS316TPY --- 17457 X5CrNiMo17122
TP 316L G 3468 SUS316LTPY --- 17457 X2CrNiMo17132
TP 321 (18Cr-10Ni-Ti) G 3468 SUS321TPY --- 17457 X6CrNiTi1810
TP 347 (18Cr-10Ni-Cb) G 3468 SUS347TPY --- 17457 X6CrN iNb1810
STANDARD SPECIFICATION
Note (i): Specify electric resistance-welding.

Note (2): Maximum carbon content shall be 0.15%.

Note (3): Specify Impact Test requirement per ASTM.

ASTM JIS/JPI BS DIN

A-524
Seamless Carbon Steel Pipe for
Atmospheric and Lower
Temperatures
Gr 1 --- --- SEW680 TTSt41
Gr 11 ---

A-587
Electric-Welded Low-Carbon
Steel Pipe for the Chemical
Industry
G 3454 STPG370 (1)(2) --- 1626 St37.0

A-671
Electric-Fusion-Welded Steel pipe
for Atmospheric and Lower
Temperatures

Grade Material
CA55 A285 Gr C
CB60 A515 Gr 60 JPI-SB42 --- ---
CB70 A515 Gr 65 JPI-SB46 --- ---
CB70 A515 Gr 70 JPI-SB49 --- ---
CC60 A516 Gr 60 JPI-SLA24B (3) --- ---
CC65 A516 Gr 65 JPI-SLA33B (3) --- ---
CD70 A537 CL 1 --- --- ---
CE55 A442 Gr 55 --- --- ---
CE60 A442 Gr 60 JPI-SPV24 --- ---
CF70 A203 Gr B --- --- ---
CF71 A203 Gr E JPI-SL3N28 --- ---
CK75 A299
STANDARD SPECIFICATION
Note (1): Specify Impact Test requirement per ASTM.

Note (2): Recognize loner minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum tensile and
yield strengths per ASTM.

ASTM JIS/JPI BS DIN

A-672
Electric-Fusion-Welded Steel Pipe
for High- Pressure Service at
Moderate Temperature

Grade Material
A55 A285 Gr C JPI-SB42 --- ---
B55 A515 Gr 55 --- --- ---
B60 A515 Gr 60 JPI-SB42 --- ---
B65 A515 Gr 65 JPI-SB46 --- ---
B70 A515 Gr 70 JPI-SB49 --- ---
C55 A516 Gr 55 --- --- ---
C60 A516 Gr 60 JPI-SLA24B (1) --- ---
C65 A516 Gr 65 JPI-SLA33B (1) --- ---
C70 A516 Gr 70 --- --- ---
D70 A537 CL 1 --- --- ---
E55 A442 Gr 55 --- --- ---
E60 A442 Gr 60 JPI-SPV24 --- ---
L65 A204 Gr A JPI-SB46M --- ---
L70 A204 Gr B JPI-SB49M (2)
L75 A204 Gr C --- --- ---
N75 A299 --- --- ---
STANDARD SPECIFICATION

ASTM/API JIS/JPI BS DIN

A-691
Carbon and Alloy Steel Pipe,
Electric-Fusion-Welded for
High- Pressure Service
at High Temperatures
Grade Material
CM-65 A204 Gr A JPI-SB46M --- ---
CM-70 A204 Gr B JPI-SB49M --- ---
CM-75 A204 Gr C --- --- ---
CMSH-70 A537 CL 1 --- --- ---
CMS-75 A299 --- --- _--
½ Cr A337 Gr 2 CL 1 --- --- ---
1 Cr A387 Gr 12 CL 1 JPI-SCMV2 --- ---
1-1/4 Cr A387 Gr 11 CL1 JPI-SCMV3 --- ---
2-1/4 Cr A387 Gr 22 CL1 JPI-SCMV4 --- ---
5 Cr A387 Gr 5 CL 1 JPI-SCMV6 --- ---
API 5L
Line Pipe
Gr A25 63452 SGP 1387 ---
Gr A 63454 STPG370 3601 ERW 360 17172 StE210.7
3601 S 360
Gr B 63454 STPG410 3601 ERW 430 (1) 17172 StE240.7
3601 S 430 (1)
3601 SAW 430 (1)
6327 Part 1-8 (1)
Gr X42 --- --- 17172 StE290.7
Gr X46 --- --- 17172 StE320.7
Gr X52 --- --- 17172 StE360.7
Gr X56 --- --- 17172 StE385.7
Gr X60 --- --- 17172 StE415.7
Gr X65 --- --- 17172 StE445.7TM
Gr X70 --- --- 17172 StE480.7TM
--- 63455 STS370 --- 1630 St37.4
--- 63455 STS410 --- 1630 St44.4
--- 63455 STS480 --- 1630 St52.4

Note (1): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or
 Table 3 TUBES

ASTM JIS BS DIN

A-161
Seamless Low-Carbon and Carbon
Molybdenum Steel Still Tubes for
Refinery Service Low Carbon Steel

G 3461 ST340 (1) (2) 3059 HFS320 (2) 17175 St35.8

3059 CFS320 (2)

Gr T1 G 3462 STBA12 (1)(2)(3) --- 17175 15Mo5

G 3467 STFA12 (2)

A-178
Electric-Resistance-Welded Carbon Steel and
Carbon-Manganese Steel
Boiler Tubes

Gr A G 3461 STB340 (40 3059 ERW320 (3) 17177 St37.8

3059 CEW320 (3)
Gr C G 3461 STB410 (4) 3059 ERW360 17177 St42.8
3059 CEW360 (3)
Gr D --- 3059 ERW440 (3) ---
3059 CEW440 (3)

A-179
Seamless Cold-Drawn Low-Carbon
Steel Heat-Exchanger and Condenser Tubes

G 3461 STB340 (1)(5)(6) 3606 CFS 320 17175 St35.8

3059 S1 360 (5)(6)

Note (1): Specify seamless.

Note (2): Maximum hardness shall be as follows:

Item Carbon Steel

Hot rolled tubes HB 137
Cold drawn tubes HB 125

Note (3): Specify killed steel.

Note (4): Specify electric resistance-welding.
Note (5): Specify cold drawn.
Note (6): Maximum hardness shall be Rockwell B72.
 STANDARD SPECIFICATION

ASTM JIS BS DIN

A-192
Seamless Carbon Steel Boiler
Tubes for High- Pressure Service

G 3-061 STB340 (1)(2) 3059 HFS 320 (2) 17175 St35.8

3059 CFS 320 (2)
3059 S1 360 (2)
3059 S2 360 (2)

A-199
Seamless Cold-Drawn Intermediate
Alloy-Steel Heat-Exchenger and
Condenser Tubes

Gr T5 G 3462 STBA25 (3)(4) 3606 CFS 625 Wbl 007/2 12CrMio195 (6)
Gr T9 G 3462 STBA26 (3)(5) 3059 S1 629-470 (3)(5) Wbl 109 X12CrMo91 (6)
3059 S2 629-470 (3)(5)
Gr T11 G 3462 STBA23 (3)(4) 3606 CFS621 17175 13CrMo44
Gr T22 G 3462 STBA24 (3)(4) 3606 CFS622 17175 10CrMo910
3059 S1 622-440 (3)(4)
3059 S2 622-440 (3)(4)

A-200
Seamless Intermediate Alloy-Steel
Still Tubs for Refinery Service

Gr T5 G 3462 STBA25 (4) 3604 CFS625 (4) Wbl 007/2 12CrMo195 (6)
G 3467 STFA25 (4) 3604 HFS625 (4)
Gr T7 --- --- ---
Gr T9 G 3462 STBA26 (5) 3604 CFS629-470 (5) Wbl 109 X12CrMo91 (6)
G 3467 STFA26 (5) 3604 HFS629-470 (5)
3059 S1 629-470 (5)
3059 S2 629-470 (5)
Gr T11 G 3462 STBA23 (4) 3604 CFS621 (4) 17175 13CrMo44
G 3467 STFA23 (4) 3604 HES621 (4)
Gr T22 G 3462 STBA24 (4) 3059 S1 622-440 (4) 17175 10CrMo910
G 3467 STFA24 (4) 3604 CFS622 (4)
3604 HFS622 (4)

Note (1): Specify seamless.

Note (2): Maximum hardness shall be Rockwell 677.

Note (3): Specify cold drawn.

Note (4): Maximum hardness shall be Rockwell 885.

Note (5): Maximum hardness shall be Rockwell B89.

Note (6): VdTuv-Herkstoftblatt

 STANDARD SPECIFICATION

ASTM JIS BS DIN

A-209
Seamless Carbon-Molybdenum
Alloy-Steel Boiler and Super
Heater Tubes

Gr T1 G 3462 STBA12 (1)(2) 3059 S1 243 (2) 17175 15Mo5

3059 S2 243 (2) ---
Gr Tla G 3462 STBA13 (1)(3) 3059 S1 243 (3) 17175 15Mo5
3059 S2 243 (3) ~
Gr Tlb --- --- ---

A-210
Seamless Medium-Carbon Steel
Boiler and Super heater Tubes
Gr A1 G 3461 STB410 (1)(4) 3059 S1 440 17175 St45.8
S2 440 (4)

A-213
Seamless Ferritic and Austenitic
Alloy-Steel Boiler, Super heater
and Heat-Exchanger Tubes

Gr T 5 G 3462 STBA25 (5) 3606 CFS 625 Wbl 007/2 12CrMo195

(7)
Gr T 11 G 3462 STBA23 (5) 3606 CFS 621 17175 13CrMo44
Gr T 12 G 3462 STBA22 (1)(5) 3506 CFS 620 17175 13CrMo44
3059 S1/S2 620 (5)
Gr T 22 G 3462 STBA24 (5) 3606 CFS 622 17175 10CrMo910
3059 S1/S2622-
440/490(5)
Gr TP 304 G 3463 SUS304 TB (1)(6) 3606 CFS 304S25 17458 X5CrNi1810
Gr TP 3D4H G 3463 SUS304H T8 (1)(6) 3059 CFS304S59 (6) ---
Gr TP 304L G 3463 SUS304L TB (1)(6) 3606 CFS304S22 17458 X2CrNi1911
Gr TP 310 G 3463 SUS310S TB (1)(6) --- ---
Gr TP 316 G 3463 SUS316 TB (1)(6) 3606 CFS316S25 17458 X5CrNiMo17122
Gr TP 316H G 3463 SUS316H TB(1)(6) 3059 CFS316S59 (6) 17459E X6CrNiMo1713
Gr TP 316L G 3463 SUS316L TB (1)(6) 3606 CFS316S29 17458 X2CrNiMo17132
Gr TP 321 G 3463 SUS321 TB (1)(6) 3606 CF5321S22 17458 X6CrNiTi1810
Gr TP 321H G 3463 SUS321H TB(1)(6) 3059 CFS321S59 (6) ---
Gr TP 347 G 3463 SUS347 TB (1)(6) 3606 CFS347S17 17458 X6CrNiNb1810
Gr TP 347H G 3463 SUS347H TB(1)(6) 3059 CFS347S59 (6) ---

Note (1): Specify seamless.

Note (2): Maximum hardness shall be Rockwell B90.
Note (3): Maximum hardness shall be Rockwell B81.
Note (4): Maximum hardness shall be Rockwell B79.
Note (5): Maximum hardness shall be Rockwell B85.
Note (6): Maximum hardness shall be Rockwell B90.
Note (7): VdTuv-Werkstoftblatt
 STANDARD SPECIFICATION

ASTM JIS BS DIN

A-214
Electric-Resistance-Welded
Carbon Steel Heat-Exchanger
and Condenser Tubes
G 3461 STB340 (1)(2) 3606 ERW 320 17177 St37.8
3059 ERW 320 (2)
3059 CEW 320 (2)
3059 ERW 360 (2)
3059 CEW 360 (2)

A-226
Electric-Resistance-Welded
Carbon Steal Boiler and
Superheater Tubes for
High-Pressure Service
G 3461 STB340 (1)(2) 3059 ERW320 (2) 17177 St37.8
3059 CEW320 (2)
3059 ERW360 (2)
3059 CEW360 (2)

A-249
Welded Austenitic Steel Boiler,
Superheater, Heat-Exchanger,
and Condense; Tubes
TP 304 G 3463 SUS304 TB (3) --- 17457 X5CrNi1810
TP 304H G 3463 SUS304H TB (3) 3059-ERW304S59 (3) ---
TP 304L G 3463 SUS304L TB (3) --- 17457 X2CrNi1911
TP 309 G 3463 SUS309S TB (3) --- ---
TP 310 G 3463 SUS310S TB (3) --- ---
TP 316 G 3463 SUS316 TB (3) --- 17457 X5CrNiMo17122
TP 316H G 3463 SUS316H TB (3) 3059-ERW316S59 (3)
TP 316L G 3463 SUS316L TB (3) --- 17457 X2CrNiMo17132
TP 321 G 3463 SUS321 TB (3) --- 17457 X6CrNiTi1810
TP 321H G 3463 SUS321H TB (3) 3059 ERW321S59 (3) ---
TP 347 G 3463 SUS347 TB (3) --- 17457 X6CrNiNb1810
TP 347H G 3463 SUS347H TB (3) 3059-ERW347S59 (3) ---

Note (1): Specify electric resistance-welding.

Note (2): Maximum hardness shall be Rockwell B72.
Note (3): Maximum hardness shall be Rockwell B90.
 STANDARD SPECIFICATION

ASTM JIS BS DIN

A-268
Seamless and Welded Ferritic
Stainless Steel Tubing for
General Service
TP 410 G 3463 SUS410 TB (1) --- ---
TP 430 G 3463 SUS430 TB (2) --- ---

A-269
Seamless and Welded Austenitic
Stainless Steel Tubing for
General Service
TP 304 G 3463 SUS304 TB (2) 3605-304S18,S25 (2) ---
TP 304L G 3463 SUS304L TB (2) 3605-304S14,S22 (2) ---
TP 316 G 3463 SUS316 TB (2) 3605-316S18,S26 (2) ---
TP 316L G 3463 SUS316L TB (2) 3605-316S14,S22 (2) ---
TP 321 G 3463 SUS321 TB (2) 3605-321S18,S22 (2) ---
TP 347 G 3463 SUS347 TB (2) 3605-347S18,S17 (2) ---

A-271
Seamless Austenitic Chromium
Nickel Steal Still Tubes for
Refinery Service
TP 304 G 3463 SUS304 TB (2)(3) 3605-304S18 (2) 17459E X6CrNi1811
G 3467 SUS304 TF (2)
TP 304H G 3463 SUS304H TB (2)(3) 3605-304S59 (2) ---
G 3467 SUS304H TF (2) 3059-CFS304S59 (2)
TP 316 G 3463 SUS316 TB (2)(3) 3605-316S18 (4) 17458 X5CrNiMo17122
G 3467 SUS316 TF (2)
TP 316H G 3463 SUS316 HTB (2)(3) 3605-316S59 (4) 17459E X6rNiMo1713
G 3467 SUS316 HTF (2) 3059-316S59 (4)
TP 321 G 3463 SUS321 TB (2)(3) 3605-321S18 (2) 17458 X6CrNiTi1810
G 3467 SUS321 TF (2)
TP 321H G 3463 SUS32114 TB (2)(3) 3605-321S59 Gr 1010 ---
(2)
G 3467 SUS321H TF (2) 3059-CFS321S59 Gr
1010(2)
TP 347 G 3463 SUS347 TB (2)(3) 3605-347S18 (2) 17458 X6CrNiNb1810
G 3467 SUS347 TF (2)
TP 347H G 3463 SUS347H TB (2)(3) 3605-347S59 (2) ---
G 3467 SUS347H TF (2) 3059-CFS347S59 (2) ---

Note (1): Maximum hardness shall be Rockwell B95.

Note (2): Maximum hardness shall be Rockwell B90.
Note (3): Specify seamless.
Note (4): Maximum carbon content shall be 0.21%
 STANDARD SPECIFICATION

ASTM JIS BS DIN

A334
Seamless and Welded Carbon
And Alloy-Steel Tubes for
Low-Temperature Service
Gr 1 G 3464 STBL380 (1) 3603 CEW410 LT50 (1) 17173 T7St35N
3603 CFS410 LT50 (1) 17174 TTSt35N
3603 ERW410 LT50 (1)
3603 HFS410 LT50 (1)
Gr 3 G 3464 STBL450 (2) 3603 CFS503 LT100 (2) 17173 10Ni14
3603 HFS503 LT100 (2)
Gr 6 --- 3603 CEW410 LT50 (2) SEW680 TTSt45N
3603 CFS410 LT50 (2)
3603 ERW410 LT50 (2)
3603 HFS4110 LT50 (2)
Gr 8 G 3464 STBL690 (2) 3603 CFS509 LT196 17173 X8Ni9
(2)
3603 HFS509 LT196
(2)

Note (1): Maximum hardness shall be Rockwell B85.

Note (2): Maximum hardness shall be Rockwell B90.
 STANDARD SPECIFICATION
Table 4 FORGINGS

ASTM JIS BS DIN

A-105
Forging, Carbon Steel,
For Piping Components
G 3202 SFVC2A 1503-221-490 ---

A-181
Forging, Carbon Steel, for
General - Purpose Piping
Class 60 G 3202 SFVC1 1503-221-430 17200 C22N
Class 70 G 3202 SFVC2A 1503-221-490 ---

A-182
Forged or Rolled Alloy-Steel
Pipe Flanges, Forged Fittings,
and Valves and Parts for
High –Temperature Service
F1 (C-1/2Mo) G 3203 SFVAF1 1503-245-420 (1) VdTuv201 16Mo5
FS (5Cr-1/2Mo) G 3203 SFAF58 1503-625-520 VdTuv1207 12CrMo195
F9 (9Cr-1Mo) G 3203 SFVAF9 --- W.St.Nr17386
X12CrMo910
F11 (1-1/4Cr-I/2Mo) G 3203 SFVAF11A 1503-621-460 SEW550 16CrMo44
F12 (1Cr-1/2Mo) G 3203 SFVAF12 1503-620-540 SEW550 13CrMo44
F21 (3Cr-1Mo) G 3203 SFVAF21B --- ---
F22 (2-1/4Cr-1Mo) G 3203 SFVAF22B 1503-622-560 SEW550 10CrMo9I0
F304 (18Cr-8Ni) G 3214 SUS304 1503-304S31 17440 X5CrNi1810
F304H (18Cr-8Ni) G 3214 SUS304H 1503-304S51 ---
F304L (18Cr-8Ni) G 3214 SUSF304L 1503-304S11 17440 X2CrNi1911
F316 (16Cr-12Ni-2Mo) G 3214 SUSF316 1503-316S31 or 33 17440 X5CrNiMo17122
F316H (16Cr-12Ni-2Mo) G 3214 SUSF316H 1503-316S51 ---
F316L (16Cr-12Ni-2Mo) G 3214 SUS316L 1503-316S11 or 13 17440 X2CrNiMo17132
F321 (18Cr-10Ni-Ti) G 3214 SUS321 1503-321S31 17440 X6CrNiTi1810
F321H (18Cr-10Ni-Ti) G 3214 SUSF321H 1503-321S51-510 ---
F347 (18Cr-10Ni-Cb) G 3214 SUSF347 1503-347S31 17440 X6CrNiNb1810
F347H (18Cr-10Ni-Cb) G 3214 SUSF347H 1503-347S51 ---

Note (1): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or
STANDARD SPECIFICATION

ASTM JIS BS DIN

A-226
Forging, Carbon Steel, for
Pressure Vessel Component

Class 1 G 3202 SFVC1 1503-221-430 17200 C22N

Class 2 G 3202 SFVC2A 1503-221-490 ---
Class 4 G 3202 SFVC2B

A-336
Steel Forging, Alloy, for Pressure Refer to A-182 Refer to A-182 Refer to A-182
and High- Temperature Parts

A-350
Forging, Carbon and Low-Alloy
Steel, Requiring Notch Toughness
Testing for Piping Component

LF1 G 3205 SFL1 1503-221-430 (1) SEW680 TTSt41

LF2 G 3205 SFL2 1640 WPLO SEW680 TTStE36
1503-221-490 (1)
LF3 (3-1/2Ni) G 3205 SFL3 1640 WPL3 17280 10Ni14
1503-503-490 (1)

A-508
Quenched and Tempered
Vacuum-Treated Carbon and Alloy
Steel Forging for Pressure Vessel

Class 1 G 3202 SFVC2B --- ---

Class 2 G 3204 SFVQ2A --- SEW640 22NiMoCr37
Class 3 G 3204 SFVQ1A --- SEW640 20MrMoNi55

A-541
Steel Forging, Carbon and Alloy
Quenched and Tempered, for
Pressure Vessel Component

Class 1 G 3202 SFVC2B 1503-221-490 (1)(2) ---

Class 2 G 3204 SFVQ2A --- ---
Class 3 G 3204 SFVQ1A --- ---

Note (1): Specify Impact Test requirement per ASTM.

Note (2): Specify heat treatment and mechanical properties per ASTM.
 STANDARD SPECIFICATION
Table 5 CASTINGS

ASTM JIS BS DIN

A-27
Steel Castings, Carbon, for
General Application
Gr 60-30 G 5101 SC410 (1) 3100 Steel A1 1681 GS-38 (2)
Gr 65-35 G 5101 SC450 (1) --- 1681 GS-45
Gr 70-36 G 5101 SC480 (1) 3100 Steel A2 1681 GS-52

A-47
Ferrltic Malleable Iron Castings

Gr 32510 G 5702 FCM3340 6681 B35-12 1692 GTS-35-10

Gr 35018 G 5702 FCM3360 --- 1692 GTS-35-10 (2)

A-48
Gray Iron Castings
Class 20 G 5501 FC150 1452 Gr 150 1691 GG-15
Class 25 G 5501 FC200 1452 Gr 180 1691 GG-20
Class 30 G 5501 FC200 (2) 1452 Gr 220 1691 GG-20 (2)
Class 35 G 5501 F 250 1452 Gr 260 1691 GG-25
Class 40 G 5501 FC300 1452 Gr 300 1691 GG-30
Class 45 G 5501 FC300 (2) 1452 Gr 300 (2) 1691 GG-30 (2)
Class 50 G 5501 FC350 1452 Gr 350 1691 GG-35
Class 55 --- 1452 Gr 400 ---
Class 60 --- ---

A-126
Gray Iron Castings for Valves
Flanges and Pipe Fittings

Class A G 5501 FC200 1452 Gr 180 1691 GG-15

Class 6 G 5501 FC250 1452 Gr 260 1691 GG-25
Class C G 5501 FC300 1452 Gr 300 1691 GG-30

Note (1): Specify carbon, manganese, or silicon contents in accordance with ASTM.
Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify minimum
tensile and yield strengths per ASTM.
 STANDARD SPECIFICATION

ASTM JIS BS DIN

A-216
Steel Castings, Carbon,
Suitable for Fusion Welding,
For High-Temperature Service
WCA G 5151 SCPH1 (1) 1504-161 Gr 430 17245 GS-C25
WCB G 5151 SCPH2 (1) 1504-161 Gr 480 17245 GS-C25
WCC --- 1504-161 Gr 540 (2)(3) ---

A-217
Steel Castings, Martensitic
Stainless and Alloy, for
Pressure-Containing Parts,
Suitable for High-Temperature
Service
WC1 (C-1/2Mo) G 5151 SCPH11 (1) 1504-245 17245 GS-22Mo4
WC6 (1-1/4Cr-1/2Mo) G 5151 SCPH21 (1) 1504-621 17245 GG-17CrMo55
WC9 (2-1/4Cr-1Mo) G 5151 SCPH32 (1) 1504-622 17245 CS-19CrMo910
C5 (Cr-1/2Ho) G 5151 SCPH61 (1) 1504-625 SEW 595 GS-2CrMo195
C12 (9Cr-1Mo) --- 1504-629 SEW 595 GS-2CrMo101

A-297
Steel Castings, Iron-Chromium
and Iron-Chromium-Nickel, Heat
Resistant, for General Application

Gr HC G 5122 SCH2 --- ---

Gr HD G 5122 SCH11 --- ---
Gr HE G 5122 SCH17 3100-309C40 ---
Gr HF G 5122 SCH12 3100-302C35 ---
Gr HH G 5122 SCH13 3100-309C30 ---
Gr HI G 5122 SCH18 --- ---
Gr HK G 5122 SCH22 or 21 3100-310C40 ---
Gr HN G 5122 SCH19 3100-311C11 ---
Gr HT G 5122 SCH15 3100-330C12 ---
Gr HU G 5122 SCH20 3100-331C60 ---

Note (1):Test and inspect the product in accordance with ASTH, except for the chemical analysis and mechanical properties of the
steel.
Note (2): Specify carbon, manganese, or silicon contents in accordance with ASTM.
Note (3): Specify elongation in accordance with ASTM.
 STANDARD SPECIFICATION

ASTM JIS BS DIN

A-338
Malleable Iron Flanges, Pipe
Fittings, and Valve Parts for
Railroad, Marine, and Other
Heavy Duty Service at
Temperatures up to 650°F
(345°C)

A-351
Steel Castings, Austenitic,
for High-Temperature Service
Gr CF3 (18Cr-8Ni) G 5121 SCS19A (1) 1504-304C12 (2) ---
3100-304C12 (2)
Gr CF3A (18Cr-8Ni) --- --- ---
Gr CF3M (17Cr-10Ni-2Mo) G 5121 SCS16A (1) 1504-316C12 (2) ---
3100-316C12 (2)
Gr CF8 (18Cr-8Ni) G 5121 SCS13A (1) 1504-304C15 17445 G-X6CrNi189
3100-304C15
Gr CF8A (18Cr-8Ni) --- --- _--
Gr CF8C (20Cr-10Ni-Cb) G 5121 SCS21 (1) 1504-347C17 17445 G-X5CrNiNb189
3100-347C17
Gr CF8M (18Cr-10Ni-2Mo) G 5121 SCS14A (1) 1504-316C16 17445 G-X6CrNiMo1810
3100-316C16
Gr CH10 (25Cr-13Ni) G 5121 SCS17 (1)(2) --- ---
Gr CH20 (25Cr-13Ni) G 5121 SCS17 (1)(3) 3100-309C30 ---
Gr CK20 (25Cr-20Ni) G 5121 SCS18 (1) --- ---
Gr CN7M (28Ni-20Cr- G 5121 SCS23 (1) 1504-332C11 ---
2Mo-3Cb)
Gr HK40 (25Cr-20Ni) G 5122 SCH22 (1) 1504-310C40 ---
3100-310C40

Note (1): Test and inspect the product in accordance with ASTM, except for the chemical analysis and mechanical properties of the
steel.
Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify
minimum tensile and yield strengths per ASTM.
Note (3): Specify mechanical properties, test and inspection in accordance with ASTM.
 STANDARD SPECIFICATION

ASTM JIS BS DIN

A-352
Steel Castings, Ferritic and
Martensitic, for Pressure-
Containing Parts Suitable for
Low-Temperature Service
LCB G 5152 SCPL1 (1) 1504-161 Gr 480 LT40 SEW685 GS-CK24
LC1 (C-1/2Mo) G 5152 SCPL11 (1) 1504-245 LT50 ---
3100-BL1
LC2 (2-1/2Ni) G 5152 SCPL21 (1) --- ---
LC3 (3-1/2Ni) G 5152 SCPL31 (1) 1504-503 LT60 SEW685 GS-10Ni14
3100-BL2
LC9 --- --- ---

A-395
Ferritic Ductile Iron Pressure-
Retaining Castings for Use at
Elevated Temperatures
88243, APPENDIX-1 2789 Gr 420/12 (2) ---
FCD-S

A-447
Steel Castings, Chromium-Nickel
-Iron Alloy Castings (25-12 Class)
for High-Temperature Service

G 5122 SCH13 (3) 3100-309C32 ---

A-494
Casting, Nickel and Nickel Alloy

M-35-1 --- 3071-NAI ---

M-30H --- 3071-NA2 (4) ---
M-25S --- 3071-NA3 ---

Note (1): Test and inspect the product in accordance with ASTH, except for the chemical analysis and mechanical properties of the
steel.
Note (2): Specify ferritizing heat treatment, chemical requirement and mechanical properties, except for tensile and yield strengths.
Note (3): Specify mechanical properties, test and inspection in accordance with ASTM
Note (4): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify
minimum tensile and yield strengths per ASTM.
 STANDARD SPECIFICATION

ASTM JIS BS DIN

A-536
Ductile Iron Castings
Gr 60-40-18 G 5502 FCD450 (1) 2789 Gr 420/12 ---
Gr 65-45-12 G 5502 FCD500 (1) 2789 Gr 500/7 1693 GGG-50
Gr 80-55-06 G 5502 FCD600 (1) 2789 Gr 600/3 (2) 1693 GGG-60
Gr 100-70-03 G 5502 FCD700 (1) 2789 Gr 700/2 (2) 1693 GGG-70

A-743
Castings, Iron-Chromium,
Iron-Chromium Nickel,
Nickel Base, Corrosion Resistant,
for General Application
Gr CA-15 G 5121 SCS1 (3) 3100-410C21 (2) 17445 G-X20Cr14
Gr CA-40 G 5121 SCS2 (3) 1504-420C29 ---
3100-420C29
Gr CF-3 G 5121 SCS19A (3) 1504-344C12 ---
3100-304C12
Gr CF-3M G 5121 SCS16A (3) 1504-316C12 ---
3100-316C12
Gr CF-8 G 5121 SCS13A (3) 1504-304C15 17445 G-X6CrNi189
3100-304C15
Gr CF-8C G 5121 SCS21 (3) 1504-347C17 17445 G-X5CrNiNb189
Gr CF-8M G 5121 SCS14A (3) 1504-316C16 17445 G-X6CrNiMo1810
3100-316C16
Gr CF-20 G 5121 SCS12 (3) --- ---
Gr CH-20 G 5121 SCS17 (3) 3100-309C30 ---
Gr CK-20 G 5121 SCS18 (3) --- ---
Gr CN-7M G 5121 SCS23 (3) 1504-332C11 ---

Note (1): Specify elongation in accordance with ASTM.

Note (2): Recognize lower minimum tensile or yield strengths of the underlined substitute materials in design consideration, or specify
minimum tensile and yield strengths per ASTM.
Note (3): Test and inspect the product in accordance with ASTM, except for the chemical analysis and mechanical properties of the
steel.
 STANDARD SPECIFICATION

Table 6 BOLTS AND NUTS

ASTM JIS BS DIN

A-193
Alloy-Steel and Stainless Steel
Bolting Materials for High
Temperature Service
Gr B5 (5Cr) G 4107 SNB5 --- ---
Gr B6 (12Cr) G 4303 SUS410 1506-410S21-772 1654 X10Cr13
Gr B7 (Cr-Mo) G 4107 SNB7 1506-630-860 17200 42CrMo4
17240 24CrMo5 (3)
Gr B7M (Cr-0.2Mo) G 4107 SNB7 (1) 1506-630-690 17200 42CrMo4
17240 24CrMo5 (3)
Gr B8 G 4303 SUS304 (2) 1506-304S31 17440 X5CrNi1810
CL 1 (304 sol.trt.)
CL 4 (304 str.hd.)
Gr B8C G 4303 SUS347 (2) 1506-347S31 17440 X6CrNiNb1810
CL 1 (347 sol.trt.)
CL 2 (347 str.hd.)
Gr B8M G 4303 SUS316 (2) 1506-316S31 17440 X5CrNiMo17122
CL 1 (316 sol.trt.)
CL 2 (316 str.hd.)
Gr B8T G 4303 SUS321 (2) 1506-321S31 17440 X6CrNiMTi1810
CL 1 (321 sol.trt.)
CL 2 (321 str.hd.)
Gr B16 (Cr - Mo - V) G 4107 SNB16 1506-670-860 17240 40CrMoV47

A-194
Carbon and Alloy Steel Nuts
for Bolts for High-Pressure
and High-Temperature Service
Gr 2H G 4051 S45C (3) 1506-162 17240 C35
1654 Cq45
Gr 4 (C-Mo) -- --- 17240 24CrMo5
Gr 6 (12Cr) G 4303 SUS410 (3) 1506-410S21-770 1654 X10Cr13
Gr 8 (304) G 4303 SUS304 (2) 1506-304S31 17440 X5CrNi1810
Gr 8MA (316) G 4303 Sus316 (2) 1506-316S31 17440 X5CrNiMo17122

A-307
Carbon Steel Externally Threaded
Standard Fasteners

Gr B G 3101 SS400 (4) 4190-Gr 4,6 17100 St44.2

17100 St44.3
G 4051 S25C (4) 17200 CK25
1654 Cq22

Note (1): Specify heat treatment and mechanical properties per ASTM.
Note (2): Specify ASTH dimensional requirements, tolerances and inspection.
Note (3): Specify mechanical properties, test and inspection in accordance with ASTM.
Note (4):Test and inspect the product in accordance with ASTM, except for the chemical analysis and mechanical properties of the steel.
 STANDARD SPECIFICATION

ASTM JIS BS DIN

A-320
Alloy Steel Bolting Materials for
Low Temperature Service
Gr L7 (Cr-Mo) G 4107 SNB7 (1) 1506-630-860 17200 42CrMo4
17240 24CrMo5
Gr L43 (Ni-Cr-Mo) G 4103 SNCM439 --- ---
Gr B8 (304 str.hd.) G 4303 SUS304 (2) 1506-304S31 17440 X5CrNi1810
Gr B8C (347 str.hd.) G 4303 SUS347 (2) 1506-347S31 17440 X6CrNiNb1810
970-347S31
Gr B8T (321 str.hd.) G 4303 SUS321 (2) 1506-321S31 17440 X6CrNiTi1810
970-321S31
Gr B8M (316 str.hd.) G 4303 SUS316 (2) 1506-316S31 17440 X5CrNiMo17I22
970-316S31

A-325
High-Strength Bolts for Structure
Steel Joints
G 4051 S33C 3139 1654 Cq35

A-354
Quenched and Tempered Alloy
Steel Bolts, Studs, and Other
Externally Threaded Fasteners

Gr BC --- --- --
Gr BD --- --- --

A-453
Bolting Materials, High-Temperature
, 50 to 120 KSI (345 to 827 Mpa)
Yield Strength, with Expansion
Coefficients Comparable to
Austenitic Steels

Gr 660 Class A & B --- --- ---

(14Cr-24Ni)
Gr 651 Class A & B --- --- ---
(19Cr-9Ni)

Note (1): Specify Impact Test requirement per ASTM.

Note (2): Specify ASTM dimensional requirements, tolerances and inspection.
 STANDARD SPECIFICATION
Table 7 BARS AND SHAPES

ASTM JIS BS DIN

A-276
Stainless and Heat-Resisting Steel
Bars and Shapes
Type 420 G4303 J1 970-420S37 17440 X20Cr13

A-576
Steel Bars, Carbon, Hot-Wrought
Special Quality

Gr 1020 G4051 S20C --- 17200 CK22

Gr 1025 G4051 S25C --- 17200 CK25
Gr 1030 G4051 S30C --- 17200 CK30
Gr 1035 G4051 S35C --- 17200 CK35
Gr 1040 G4051 S40C --- 17200 CK40
Gr 1045 G4051 S45C --- 17200 CK45

A-615
Deformed and Plain Billet-Steel
Bars for Concrete Reinforcement
Gr 40 G3112 SD295 Gr 250 (1) --
Gr 60 G3112 SD390 (1) Gr 460/425 (1) 488 BSt420S

A-675
Steel Bars, Carbon, Hot-Wrought,
Special Quality, Mechanical
Properties

Gr 45 G3101 SS330 Gr 40A (1) 17100 St33

Gr 50 G3101SS330 (1) Gr 40A (1) 17100 St33
Gr 55 G3101 SS400 Gr 40A (1) 17100 St44-2
17100 St44-3
Gr 60 G3101 SS400 (1) Gr 43A 17100 St44-2
17100 St44-3
Gr 65 G3101 SS490 Gr 50A (1) 17100 St52-3
Gr 70 G3101 SS490 Gr 55C or 50A (1) 17100 St52-3
Gr 75 G3101 SS540 Gr 55C or 50A (1) ---
Gr 80 G3101 SS540 (1) Gr 55C (1) ---

Note (1): Recognize loser minimum tensile or yield strengths of the underlined substitute materials in design consideration, or
 STANDARD SPECIFICATION

Table 8 PIPING FITTINGS

ASTM JIS BS DIN

A-234
Piping Fittings of Wrought Carbon
Steel and Alloy Steel for Moderate
and Elevated Temperatures

WPB B 2312 PT410 1640 WPB ---

6 2313 PT410W
WPC B 2312 PT480 --- ---
B 2313 PT480W
WP1 (C-1/2Mo) B 2312 PA12 1640 WP1 ---
B 2313 PA12W
WP5 (5Cr-1/2Mo) B 2312 PA25 1640 WP5 ---
B 2313 PA25W
WP9 (9Cr-1/2Mo) 8 2312 PA26 --- ---
B 2313 PA-96W
WP11 (1-1/4Cr-1/2Mo) B 2312 PA23 1640 WP11 ---
B 2313 PA23W
WP12 (1Cr-1/2Mo) B 2312 PA22 --- ---
B 2313 PA22W
WP22 (2-1/4Cr-1Mo) B 2312 PA24 1640 WP22 ---
8 2313 PA24W

A-403
Wrought Austenitic Stainless Steel
Piping Fittings
WP 304 (18Cr-8Ni) B2312 SUS304 1640-WP304 ---
B2313 SUS304W
WP 304H(18Cr-8Ni) B2312 SUS304H --- ---
WP 304L (18Cr-8Ni) B2312 SUS304L 1640-WP304L ---
B2313 SUS304LW
WP 316 (16Cr-12Ni-2Mo) B2312 SUS316 1640-WP316 ---
B2313 SUS316W
WP 316H (16Cr-12Ni-2Mo) B2312 SUS316H --- ---
WP 316L (16Cr-12Ni-2Mo) B2312 SUS316L 1640-WP316L ---
B2313 SUS316LW
WP 321 (18Cr-10Ni-Ti) B2312 SUS321 1640-WP321 ---
B2313 SUS321W
WP 321H (18Cr-10Ni-Ti) B2312 SUS321H --- ---
WP 347 (18Cr-10Ni-Cb) B2312 SUS347 1640-WP347 ---
B2313 SUS347W
WP 347H (18Cr-10Ni-Cb) B2312 SUS347H --- ---
STANDARD SPECIFICATION

JIS BS DIN
A-420
Piping Fittings of Wrought Carbon
Steel and Alloy Steel for Low
Temperature Service
WL3 (3-1/2Ni) B 2312 PL450 1640-WPL3 ---
B 2313 PL450W
WL6 B 2312 PL380 1640-WPL0 ---
B 2313 PL38OW
WL8 (9Ni) B 2312 PL690 --- ---
 STANDARD SPECIFICATION

Table 9 NONFERROUS MATERIALS

ASTM JIS BS DIN

PIPE

B-42
Seamless Copper Pipe, Standards H3300 C1020 2871-C103 1787 OF-Cu
Sizes

B-43
Seamless Red Brass Pipe, H3300 C4430 --- 17671 CuZn15
Standard Sizes

B-165
Nickel-Copper Alloy Seamless
Pipe and Tube
N04400 H4552 NCUT 3074 ---

B-167
Nickel-Chromium-Iron Alloys
Seamless Pipe and Tubes

N06600 G4903 NCF600TP

B-337
Seamless and Welded Titanium
and Titanium Alloy pipe

Gr 1 H4630 TTP28 --- 17850 Ti1

Gr 2 H4630 TTP35 --- 17850 Ti2
Gr 3 H4630 TTP49 --- 17850 Ti3
Gr 7 --- ---

B-407
Nickel-Iron-Chromium. Alloy
Seamless Pipe and Tube

N08800 G4903 NCF 800TP --- ---

N08810 G4903 HCF 800HTP --- ---
G4903 NCF 825TP --- ---

B-466
Seamless Copper-Nickel Pipe
and Tube
C70600 H3300 C7060 2871-CN102 17664 CuNi10Fe1Mn
C71500 H3300 C7150 2871-CN107 17664 CuNi30Mn1Fe
STANDARD SPECIFICATION

ASTM JIS BS DIN

B-467
Welded Copper-Nickel Pipe

C70600 H3320 C7060 2871-CN102 17664 CuNi10Fe1Mn

C71500 H3320 C7150 2871-CN107 17664 CuNi30Mn1Fe

CASTINGS
B-61
Steam or Valve Bronze Castings H5111 BC7 1400-LG4 ---

B-62
Composition Bronze or Ounce H5111 BC6 1400-LG2 1705 G-CuSn5ZnPb
Metal Castings
][®

Austenitic stainless steel

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

201 SUS 201 S 201 00 1.4372 (EN) X12CrMnNiN17-7-5

QMS 5
202 SUS 202 S 202 00
S 209 10
S 215 00
S 245 65
219 X4CrNiMn21-9-6
301 SUS 301 S 301 00 1.4310 (EN) X10CrNi18-8
301 L 1.4318 (EN) X2CrNiN18-7
302 SUS 302 S 302 00 1.4319 X10CrNi18-9
303 SUS 303 S 303 00 1.4305 (EN) X8CrNiS18-9
SUS 303 Cu
SUS 303 HS2
SUS 303 HS3
303 Se SUS 303 Se S 303 23 X10CrNiS18-9
304 SUS 304 S 304 00 1.4301 (EN) X6CrNi18-10
304 Cu SUS XM 7 S 304 30
304 L SUS 304 L S 304 03 1.4306 (EN) X2CrNi19-11
304 L SUS 304 L S 304 03 1.4307 (EN) X2CrNi18-9
SUS 304 ELC
304 H SUS 304 H S 304 09 1.4948 X8CrNi19-10
SUS 304 Cu1
SUS 304 Cu2
S 304 15 1.4891
S 304 15 1.4818
304 N SUS 304 N1 S 304 51 X5CrNiN18-10
SUS 304 N2
304 LN SUS 304 LN S 304 53 1.4311 (EN) X2CrNiN18-10
SUS 304 MF
305 SUS 305 S 305 00 1.4303 (EN) X8CrNi18-12
SUS 305 J1
F 46 S 306 00 1.4361 (EN) X1CrNiSi18-15-4
S 306 15
308
309 S 309 00 1.4828 X15CrNi23-13
309 S 309 00 1.4829
309 S SUS 309 S S 309 08 1.4828 X15CrNiSi20-12
309 S SUS 309 S S 309 08 1.4833 X6CrNi22-13
309 S SUS 309 S S 309 08 1.4833 X12CrNi23-13
309 H S 309 09 1.4833
309 Cb S 309 40

www.weisz.com Steel grades equivalence tables Pág. 1

][®

Austenitic stainless steel

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

309 HCb S 309 41

310 1.4841 X15CrNiSi25-20
310 1.4845 X12CrNi25-20
SUS 310 ELC
310 L 1.4335 (EN) X1CrNi25-21
310 L 1.4466 (EN) X1CrNiMoN25-22-2
310 S SUS 310 S S 310 08 1.4842 X6CrNi25-20
310 S SUS 310 S S 310 08 1.4845 (EN) X8CrNi25-21
310 H S 310 09 1.4845
310 Cb S 310 40
310 HCb S 310 41
310 HCbN S 310 42
310 SCB
S 310 50 1.4465 X1CrNiMoN25-25-2
S 310 50 1.4466 (EN) X1CrNiMoN25-22-2
F44 S 312 54 1.4547 (EN) X1CrNiMoCuN20-18-7
314 SUS 314 S 314 00 1.4841 X15CrNiSi25-20
316 SUS 316 S 316 00 1.4401 (EN) X5CrNiMo17-12-2
316 SUS 316 S 316 00 1.4436 (EN) X3CrNiMo17-13-3
316 Cb S 316 40 1.4580 (EN) X6CrNiMoNb17-12-2
316 F SUS 316 F S 316 20 1.4427 X6CrNiMoS18-11
316 L SUS 316 L S 316 03 1.4404 (EN) X2CrNiMo17-12-2
316 L SUS 316 L S 316 03 1.4406 X2CrNiMoN17-11-2
316 L SUS 316 L S 316 03 1.4432 (EN) X2CrNiMo17-12-3
316 L SUS 316 L S 316 03 1.4435 (EN) X2CrNiMo18-14-3
316 L SUS 316 L S 316 03 1.4441 X6CrNiMo17-11
316 H SUS 316 H S 319 09 1.4919 X6CrNiMo17-12
SUS 316 J1
SUS 316 J1L
316 N SUS 316 N S 316 51 1.4406 (EN) X2CrNiMoN17-11-2
316 LS 1.4436 (EN) X3CrNiMo17-13-3
316 LS 1.4435 (EN) X2CrNiMo18-14-3
316 LN SUS 316 LN S 316 53 1.4406 X2CrNiMoN17-11-2
316 LN SUS 316 LN S 316 53 1.4429 (EN) X2CrNiMoN17-13-3
316 LN SUS 316 LN S 316 53 1.3952 X2CrNiMoN18-14-3
316 LN SUS 316 LN S 316 53 1.4910
316 S
316 Ti SUS 316 Ti S 316 35 1.4571 (EN) X6CrNiMoTi17-12-2
316 Ti SUS 316 Ti S 316 35 1.4573 X10CrNiMoTi17-13-3
317 SUS 317 S 317 00
SUS 317 J1

www.weisz.com Steel grades equivalence tables Pág. 2

][®

Austenitic stainless steel

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

317 L SUS 317 L S 317 03 1.4438 (EN) X2CrNiMo18-15-4

317 L S 317 03 1.4434 (EN) X2CrNiMoN18-12-4
317 LM S 317 25
317 LN S 317 53 1.4439 (EN) X2CrNiMoN17-13-5
317 LMN S 317 26 1.4439 (EN) X2CrNiMoN17-13-5
F 48 S 317 26 1.4439 (EN) X2CrNiMoN17-13-5
318
319
319 L
321 SUS 321 S 321 00 1.4541 (EN) X6CrNiTi18-10
321 SUS 321 S 321 00 1.4878 X12CrNiTi18-9
321 H SUS 321 H S 321 09 1.4878 X12CrNiTi18-9
321 H SUS 321 H S 321 09 1.4941 X7CrNiTi18-11
S 326 15
S 326 54
327 1.4821
S 327 50
S 328 03
333
S 332 28
347 SUS 347 S 347 00 1.4550 (EN) X6CrNiNb18-10
347 H SUS 347 H S 347 09 1.4961 X6CrNiNb18-12
347 HFG
348 S 348 00 1.4878
348 H S 348 09
S 353 15 1.4835
926 1.4529 (EN) X1NiCrMoCuN25-20-7
21-6-9 S219 04
22-13-5 S 209 10 1.3964 X2CrNiMnMoNNb21-16-5-3
16-8-2H
XM-10 S 219 00
XM-11 S 219 04
XM-15 S 381 00
SUS XM 15J1
XM-17 S 216 00
XM-18 S 216 03
XM-19 S 209 10 1.3964 X2CrNiMnMoNNb21-16-5-3
XM-19 SUS XM 19 S 209 10 1.3974 X2CrNiMnMoNNb23-17-6-3
XM-21 S 304 52
XM-29 S 240 00
XM-31 S 214 00

www.weisz.com Steel grades equivalence tables Pág. 3

][®

Austenitic stainless steel

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

1.4371 (EN) X2CrMnNiN17-7-5

1.4373 (EN) X12CrMnNiN18-9-5
1.4537 (EN) X1CrNiMoCuN25-25-5
1.4577 X5CrNiMoTi25-25
1.4848
X6CrNiCu18-10-4Kd

High temperature austenitic stainless steel

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

Alloy 286 S 662 86 1.4980 X5NiCrTi26-15

1.4961 X8CrNiNb16-3
1.4981 X8CrNiMoNb16-16
1.4988 X8CrNiMoVNb16-13

www.weisz.com Steel grades equivalence tables Pág. 4

][®

Ferritic stainless steel

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

405 SUS 405 S 405 00

409 S 409 00 1.4512 (EN) X2CrTi12
409 L
SUS 410 LC
410 S S 410 08 1.4516 (EN) X6CrNiTi12
410 Ti SUS 410 Ti
418
429 SUS 429 S 429 00
430 SUS 430 S 430 00 1.4016 (EN) X6Cr17
430 F SUS 430 F S 430 20
430 Cb S 430 40 1.4511 X3CrNb17
430 Ti SUS 430 Ti S 430 35
430 Ti SUS 430 Ti S 430 36
434 SUS 434 S 434 00 1.4113 X6CrMo17-1
436 1.4536
439 S 430 35 1.4510 (EN) X3CrTi17
439 L
440 A S 440 00 1.4522
440 B S 440 00
441 1.4509 (EN) X2CrTiNb18
442
443 SUS 443 S 443 00
444 QS 192 S 444 00 1.4521 (EN) X2CrMoTi18-2
446 SUH 446 S 446 00 1.4749 X18CrN28
455
490
501
XM-15
QS 25T
XM-27 QS 261 S 446 27
XM-33 S 446 26
18-2 QS 192 S 444 00 1.4521 (EN) X2CrMoTi18-2
19-3 QS 192 S 444 00 1.4521 (EN) X2CrMoTi18-2
25-4-4 S 446 35
26-3-3 S 446 60
29-4 S 447 00
29-4C S 447 35
29-4-2 S 448 00
P9 S 504 00
S 890 40
S 890 25

www.weisz.com Steel grades equivalence tables Pág. 5

][®

Ferritic stainless steel

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

S 890 26
1.4000 (EN) X6Cr13
1.4002 (EN) X6CrAl13
1.4003 (EN) X2CrNi12
1.4017 (EN) X6CrNi17-1
1.4024 X15Cr13
1.4505
1.4506
1.4513 (EN) X2CrMoTi17-1
1.4520 (EN) X2CrTi17
1.4526 (EN) X6CrMoNb17-1
1.4575
1.4590 (EN) X2CrNbZr17
1.4592 (EN) X2CrMoTi29-4
1.4605 (EN) X2CrAlTi18-2
1.4724
Y 4L
SIC 8
SIC 9
SIC 10
SIC 12

Heat resistant ferritic stainless steel

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

1.4713 X10CrAl7
1.4742 X10CrAl18
1.4781 X10CrAl24

www.weisz.com Steel grades equivalence tables Pág. 6

][®

Duplex (ferritic / austenitic) stainless steel

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

2205 QS 2205 S 318 03 1.4462 (EN) X2CrNiMon22-5-3

2205 S 322 05
2304 S 323 04 1.4462 (EN) X2CrNiMoN22-5-3
2506 S 312 60
2507 S 327 50 1.4410 (EN) X2CrNiMoN25-7-4
2550 S 325 50 1.4460
2550 QSA 2505 S 325 50 1.4507 (EN) X2CrNiMoCuN25-6-3
F 50 S 312 00 1.4460 X3CrNiMoN27-5-2
F 51 QS 2205 S 318 03 1.4462 (EN) X2CrNiMoN22-5-3
F 51 S 322 05
F 52 S 329 50
F 53 S 327 50 1.4410 (EN) X2CrNiMoN25-7-4
F 54 S 327 40
F 55 S 327 60 1.4501 (EN) X2CrNiMoCuWN25-7-4
S 312 54
QS 1905 S 315 00 1.4417 X2CrNiMoSi19-5
S 317 60
329 SUS 329 J1 S 329 00
SUS 329 J2L
4462
1.4362 (EN) X2CrNiN23-4
S 392 74

www.weisz.com Steel grades equivalence tables Pág. 7

][®

Martensitic stainless steel

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

403 SUS 403 S 403 00

S 408 00
410 SUS 410 S 410 00 1.4006 (EN) X12Cr13
414
SUS 410 J1
410 S S 410 08 1.4006 (EN) X12Cr13
S 410 50 1.4030
F6NM S 415 00 1.4313 (EN) X3CrNiMo13-4
416 SUS 416 S 416 00
SUS 416 HS2
SUS 416 L
416Se
420 S 420 00 1.4021 (EN) X20Cr13
S 420 10 1.4021 (EN) X20Cr13
420 SUS 420 J1 S 420 00 1.4028 (EN) X30Cr13
SUS 420 J2
SUS 420 J2C
SUS 420 J2L
420 F SUS 420 F S 420 20
F3NM S 424 00 1.4320 X2CrNiMo13-4
SUS 429 J1
431 SUS 431 S 431 00
440 A S 440 00
440 C SUS 440 C S 440 04
SUS 440 F
XM 12 S 155 00 1.4545 X5CrNiCuNb15-5-4
1.4031 (EN) X39Cr13
1.4034 (EN) X46Cr13
1.4116 (EN) X50CrMoV15
1.4122 (EN) X39CrMo17-1
1.4418 (EN) X4CrNiMo16-5-1
1.4922 X20CrMoV12-1
1.4935 X20CrMoWV12-1
QD 51
QPD 5
Y 2L
Y 2LF

www.weisz.com Steel grades equivalence tables Pág. 8

][®

High temperature martensitic stainless steel

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

F 91 1.4903 X10CrMoVNb9-1
1.4913 X19CrMoVNbN11-1
1.4922 X20CrMoV12-1

Antimagnetic stainless steel

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

QMR 1L
QMR 2L
QMR 3L
QMR 4L
QMR 5L
1.3951 X2CrNiMoN22-15

www.weisz.com Steel grades equivalence tables Pág. 9

][®

Precipitation hardening stainless steel

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

1.4532 (EN) X8CrNiMoAl15-7-2

630 S 174 00 1.4542 (EN) X5CrNiCuNb16-4
1.4568 (EN) X7CrNiAl17-7
631 SUS 631 S 177 00
16-6 PH
AM 350
AM 355
Alloy 15-5 PH
Alloy 17-4 PH
Alloy 17-7 PH
Alloy 718
USS Stainless W

High molybdenum alloy

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

Alloy 29-4 S 447 35

Alloy 29-4-2
Alloy 254 SMO S 312 54 1.4547 (EN) X1CrNiMoCuN20-18-7
Alloy 256 MO N 08 926 1.4529 (EN) X1NiCrMoCuN25-20-7
Alloy 654 SMO S 326 54 1.4652
Alloy 904 L QS 2025 MC N 08 904 1.4539 (EN) X1NiCrMoCu25-20-5
Alloy 1925 HMO N 08 925
Alloy C-276 N 10 276
Alloy C-1008
Alloy C-1010
Alloy F 49 S 345 65 1.4565 X3CrNiMnMoNbN23-17-5-3
QS 2025 MT N 08 320
1.4583 X6CrNiMoN18-12
X1NiCrMoCuN20-18-7

www.weisz.com Steel grades equivalence tables Pág. 10

][®

High nickel alloy

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

QS 20 Cb3 N 08 020
QS 2830 N 08 028 1.4563 (EN) X1NiCrMoCu31-27-4
N 08 310
N 05 500 2.4375
Alloy B2 N 10 665
Alloy C4 N 06 455 2.4610
Alloy CP Gr2 R 50 400
Alloy C22 N 06 022 2.4602
N 06 059 2.4605
Alloy C-276 QA C276 N 10 276 2.4819
Alloy G QA G N 06 007
N 06 617 2.4663
Alloy G-3 QA G3 N 06 985
Alloy G-30 N 06 030
Alloy K-500
Alloy L-605 R 30 605
Alloy HX
Alloy MP35N
Alloy X QA X N 06 002
Alloy X-750
Alloy 6AC
Alloy 6XN N 08 367
Alloy 20
Alloy 25
Alloy 31 N 08 031 1.4562
Alloy 41XX
Alloy 42
Alloy 43XX
Alloy 52
Alloy 59 N 06 059
Alloy 188
Alloy 205
Alloy 220
Alloy 222
Alloy 230
Alloy 253 RMA
Alloy 400 QA 400 N 04 400 2.4360 NiCu30
Alloy 556
Alloy 600 NCF 600 N 06 600 2.4816 NiCr15Fe
Alloy 600 NCF 600 N 06 600 2.4640 NiCr15Fe
Alloy 601 NCF 601 N 06 601 2.4851 NiCr23Fe

www.weisz.com Steel grades equivalence tables Pág. 11

][®

High nickel alloy

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

Alloy 602 2.4633

Alloy 622 N 06 622
Alloy 625 QA 625 N 06 625 2.4856
Alloy 686
Alloy 690 N 06 690 2.4642 NiCr29Fe
JS 700 QS 2025 M N 08 700
Alloy 718 N 07 718 2.4668 NiCr19NbMo
Alloy 800 NCF 800 N 08 800 1.4558 X2NiCrAlTi32-20
Alloy 800 N 08 800 1.4958 X5NiCrAlTi31-20
Alloy 800 NCF 800 N 08 800 1.4876 X10NiCrAlTi32-20
Alloy 800 H NCF 800 H N 08 810 1.4958 X8NiCrAlTi32-21
Alloy 800 HT N 08 811 1.4959 X8NiCrAlTi32-21
Alloy 825 NCF 825 N 08 825 2.4858 NiCr21Mo
N 08 840
Alloy 902
Cupronickel 10 C 706 00 2.0872 CuNi10Fe
Cupronickel 30 C 715 00 2.0882 CuNi30Mn1Fe
Alloy 330 1.4864 X12NiCrSi36-16
1.4877
2.4973 NiCr19CoMo

High temperature alloy

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

Alloy A 286 S 662 86

Alloy MP-35N R 30 035
Alloy X 750 N 07 750
Alloy 102 N 06 102
Alloy 253MA or F45 S 308 15 1.4835
Alloy 330 N 08 330
Alloy 333 N 06 333
Alloy 617 N 06 617

www.weisz.com Steel grades equivalence tables Pág. 12

][®

Metals

USA, Japan Europe

AISI JIS UNS EN / DIN EN / DIN

grade grade designation numerical symbolical
designation designation

Titanium 3Al 2.5V

Titanium Beta C
Titanium Gr 1 3.7025
Titanium Gr 2 3.7035
Titanium Gr 3 3.7055
Titanium Gr 4
Titanium Gr 7 3.7235
Titanium Gr 11 3.7225
Titanium Cr 12
Titanium T40
Titanium T40 Gr2
Zircaloy 1
Zircaloy 2
Zirconium
Zirconium 2.5Nb
Hafnium
Copper
Nickel 200 Ni 200 N 02 200 2.4060
Nickel 201 Ni 201 N 02 201 2.4061
Nickel 200 N 02 200 2.4066
Nickel 201 N 02 201 2.4068
Nickel 270

www.weisz.com Steel grades equivalence tables Pág. 13

MARYLAND METRICS Technical Data Chart A short general listing of popular materials

International Material Grade Comparison Table The standards that correspond with DIN Material Numbers can only be compared approximately.
The use of these equivalents has to be evaluated on a case-by-case basis.
Steel
Werkstoff Germany U.S.A. France Great Britain Italy Sweden Spain Japan
No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS
Plain Steel, Cast Steel, Free-Machining Steel
1.0332 St14 1008 14491CR 1447
1.1121 Ck10 1010 CC10 040A10 1264 S10C
1.0721 10S20 1108 210M15
1.0401 C15 1015 CC12 080M15 C15C16 1350 F.111 S15C
1.0402 C22 1020 CC20 050A20 C20C21 1450 F.112
1.1141 Ck15 1015 XC12 080M15 C16 1370 C15K S15C
1.0036 USt37-3 FE37BFU
1.0715 9SMn28 1213 S250 230M07 CF9SMn28 1912 11SMn28 SUM22
1.0718 9SMnPb28 12L3 S250Pb CF9SMnPb28 1914 11SMnPb28 SUM22L
1.0501 C35 1035 CC35 060A35 C35 1550 F.113 S35C
1.0503 C45 1045 CC45 080M46 C45 1650 F.114 S45C
1.1158 Ck25 1025 XC25 070M25 C25 S25C
1.1183 Cf35 1035 XC38TS 060A35 C36 1572 S35C
1.1191 Ck45 1045 XC42 080M46 C45 1672 C45K S45C
1.1213 Cf53 1050 XC48TS 060A52 C53 1674 S50C
1.5415 15Mo3 ASTMA204GrA 15D3 1501-240 16Mo3KW 2912 16Mo3
1.5423 16Mo5 4520 1503-245-420 16Mo5 16Mo5 SB450M
1.0050 St50-2 FE50 SM50YA
1.7242 16CrMo 4 18CrMo4 18CrMo4
1.7337 16CrMo 4 4 A387Gr.12Cl. A18CrMo45KW
1.7362 12CrMo 19 5 Z10CD5.05 3606-625 16CrMo205
1.0060 St60-2 FE60-2 SM570
1.0535 C55 1055 070M55 C55 1655 S55C
1.0601 C60 1060 CC55 080A62 C60 S60C
1.1203 Ck55 1055 XC55 070M55 C50 C55K S55C
1.1221 Ck60 1060 XC60 080A62 C60 1678 S58C
1.1545 C1051 C100KU SK3
1.1545 C105W1 C100KU SK3
1.0070 St70-2 FE70-2
1.7238 49CrMo4
1.7561 42CrV6
1.7701 51CrMoV4 51CDV4 51CrMoV4
Low-Alloy Steel, Cast Steel, Free-Machining Steel
1.2067 100Cr6 L3 Y100C6 BL3 100Cr6 SUJ2
1.2210 115CrV3 L2 100C3 107CrV3KU
1.2241 51CrV4
1.2419 105WCr6 105WC13 10WCr6 2140 105WCr5 SKS31
Werkstoff Germany U.S.A. France Great Britain Italy Sweden Spain Japan
No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS
1.2419 105WCr6 105WC13 107WCr5KU SKS31
1.2542 45WCrV7 S1 BS1 45WCrV8KU 2710 45WCrSi8
1.2550 60WCrV7 S1 55WC20 58WCr9KU ~2710
1.2713 55NiCrMoV6 L6 55NCDV7 F.520.S SKH1;SKT4
1.2721 50NiCr13 ~2550
1.2762 75CrMoNiW67
1.2762 75CrMoNiW67
1.2842 90MnCrV8 O2 90MV8 BO2 88MnV8KU
1.3505 100Cr6 52100 100C6 534A99 100Cr6 2258 SUJ2
1.5622 14Ni6 ASTMA350LF5 16N6 14Ni6 15Ni6
1.5732 14NiCr10 3415 14NC11 16NiCr11 15NiCr11 SNC415(H)
1.5752 14NiCr14 3415;3310 12NC15 655M13 SNC815(H)
1.6511 36CrNiMo4 9840 40NCD3 816M40 38NiCrM04(KB) 33NiCrMo4 SNCM447
1.6523 21NiCrMo2 8620 20NCD2 805M20 20NiCrMo2 2506 20NiCrMo2 SNCM220(H)
1.6546 40NiCrMo22 8740 311-TYPE7 40NiCrM02(KB) 40NiCrMo2 SNCM240
1.6582 35CrNiMo6 4340 35NCD6 817M40 35NiCrMo6(KB) 2541 SNCM447
1.6587 17CrNiMo6 18NCD6 820A16 14NiCrMo13
1.6657 14NiCrMo34 832M13 15NiCrMo13 14NiCrMo131
1.7033 34Cr4 5132 32C4 530A32 34Cr4(KB) 35Cr4 SCR430(H)
1.7035 41Cr4 5140 42C4 530M40 42Cr4 SCR440(H)
1.7045 42Cr4 5140 42C4TS 530A40 41Cr4 2245 42Cr4 SCr440
1.7131 16MnCr5 5115 16MC5 (527M20) 16MnCr5 2511 16MnCr5 SCR415
1.7176 55Cr3 5155 55C3 527A60 SUP9(A)
1.7218 25CrMo4 4130 25CD4 1717CDS110 25CrMo4(KB) 2225 55Cr3 SM420;SCM430
1.7220 34CrMo4 4137;4135 35CD4 708A37 35CrMo4 2234 34CrMo4 SCM432;SCCRM3

Werkstoff Germany U.S.A. France Great Britain Italy Sweden Spain Japan
No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS
Plain Steel, Cast Steel, Free-Machining Steel
1.0332 St14 1008 14491CR 1447
1.1121 Ck10 1010 CC10 040A10 1264 S10C
1.0721 10S20 1108 210M15
1.0401 C15 1015 CC12 080M15 C15C16 1350 F.111 S15C
1.0402 C22 1020 CC20 050A20 C20C21 1450 F.112 S20C,S22C
1.1141 Ck15 1015 XC12 080M15 C16 1370 C15K S15C
1.0036 USt37-3 FE37BFU
1.0715 9SMn28 1213 S250 230M07 CF9SMn28 1912 11SMn28 SUM22
1.0718 9SMnPb28 12L3 S250Pb CF9SMnPb28 1914 11SMnPb28 SUM22L
1.0501 C35 1035 CC35 060A35 C35 1550 F.113 S35C
1.0503 C45 1045 CC45 080M46 C45 1650 F.114 S45C
1.1158 Ck25 1025 XC25 070M25 C25 S25C
1.1183 Cf35 1035 XC38TS 060A35 C36 1572 S35C
1.1191 Ck45 1045 XC42 080M46 C45 1672 C45K S45C
1.1213 Cf53 1050 XC48TS 060A52 C53 1674 S50C
Werkstoff Germany U.S.A. France Great Britain Italy Sweden Spain Japan
No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS
1.5415 15Mo3 ASTMA204GrA 15D3 1501-240 16Mo3KW 2912 16Mo3
1.5423 16Mo5 4520 1503-245-420 16Mo5 16Mo5 SB450M
1.0050 St50-2 FE50 SM50YA
1.7242 16CrMo 4 18CrMo4 18CrMo4
1.7337 16CrMo 4 4 A387Gr.12Cl. A18CrMo45KW
1.7362 12CrMo 19 5 Z10CD5.05 3606-625 16CrMo205
1.0060 St60-2 FE60-2 SM570
1.0535 C55 1055 070M55 C55 1655 S55C
1.0601 C60 1060 CC55 080A62 C60 S60C
1.1203 Ck55 1055 XC55 070M55 C50 C55K S55C
1.1221 Ck60 1060 XC60 080A62 C60 1678 S58C
1.1545 C1051 C100KU SK3
1.1545 C105W1 C100KU SK3
1.0070 St70-2 FE70-2
1.7238 49CrMo4
1.7561 42CrV6
1.7701 51CrMoV4 51CDV4 51CrMoV4
Low-Alloy Steel, Cast Steel, Free-Machining Steel
1.2067 100Cr6 L3 Y100C6 BL3 100Cr6 SUJ2
1.2210 115CrV3 L2 100C3 107CrV3KU
1.2241 51CrV4
1.2419 105WCr6 105WC13 10WCr6 2140 105WCr5 SKS31
1.2419 105WCr6 105WC13 107WCr5KU SKS31
1.2542 45WCrV7 S1 BS1 45WCrV8KU 2710 45WCrSi8
1.2550 60WCrV7 S1 55WC20 58WCr9KU ~2710
1.2713 55NiCrMoV6 L6 55NCDV7 F.520.S SKH1;SKT4
1.2721 50NiCr13 ~2550
1.2762 75CrMoNiW67
1.2762 75CrMoNiW67
1.2842 90MnCrV8 O2 90MV8 BO2 88MnV8KU
1.3505 100Cr6 52100 100C6 534A99 100Cr6 2258 SUJ2
1.5622 14Ni6 ASTMA350LF5 16N6 14Ni6 15Ni6
1.5732 14NiCr10 3415 14NC11 16NiCr11 15NiCr11 SNC415(H)
1.5752 14NiCr14 3415;3310 12NC15 655M13 SNC815(H)
1.6511 36CrNiMo4 9840 40NCD3 816M40 38NiCrM04(KB) 33NiCrMo4 SNCM447
1.6523 21NiCrMo2 8620 20NCD2 805M20 20NiCrMo2 2506 20NiCrMo2 SNCM220(H)
1.6546 40NiCrMo22 8740 311-TYPE7 40NiCrM02(KB) 40NiCrMo2 SNCM240
1.6582 35CrNiMo6 4340 35NCD6 817M40 35NiCrMo6(KB) 2541 SNCM447
1.6587 17CrNiMo6 18NCD6 820A16 14NiCrMo13
1.6657 14NiCrMo34 832M13 15NiCrMo13 14NiCrMo131
1.7033 34Cr4 5132 32C4 530A32 34Cr4(KB) 35Cr4 SCR430(H)
1.7035 41Cr4 5140 42C4 530M40 42Cr4 SCR440(H)
1.7045 42Cr4 5140 42C4TS 530A40 41Cr4 2245 42Cr4 SCr440
1.7131 16MnCr5 5115 16MC5 (527M20) 16MnCr5 2511 16MnCr5 SCR415
Werkstoff Germany U.S.A. France Great Britain Italy Sweden Spain Japan
No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS
1.7176 55Cr3 5155 55C3 527A60 SUP9(A)
1.7218 25CrMo4 4130 25CD4 1717CDS110 25CrMo4(KB) 2225 55Cr3 SM420;SCM430
1.7220 34CrMo4 4137;4135 35CD4 708A37 35CrMo4 2234 34CrMo4 SCM432;SCCRM3
Plain Steel, Cast Steel, Free-Machining Steel
1.7223 41CrMo4 4140;4142 42CD4TS 708M40 41CrMo4 2244 42CrMo4 SCM440
1.7225 42CrMo4 4140 42CD4 708M40 42CrMo4 2244 42CrMo4 SCM440(H)
1.7262 15CrMo5 12CD4 2216 12CrMo4 SCM415(H)
1.7335 13CrMo4 4 ASTMA182 15CD3.5/4.5 1501-620-Gr27 14CrMo45 14CrMo45 SPVAF12
1.7361 32CrMo12 30CD12 722M24 32CrMo12 2240 F.124.A
1.7380 10CrMo9 10 ASTMA182F.22 SPV 1501-622Gr31;45
1.7715 14MoV6 3 1503-660-440 13MoCrV6
1.8159 50CrV4 6150 50CrV4 735A50 50CrV4 2230 51CrV4 SUP10
1.8159 50CrV4 6150 735A50 51CrV4 2230 SUP10
1.3501 100Cr2 E50100 100C2
1.5710 36NiCr6 3135 35NC6 640A35 SNC236
1.5736 36NiCr10 3435 30NC11 SNC631(H)
1.5755 31NiCr14 SNC836 18NC13 653M31
1.7733 24CrMoV55 20CDV6 21CrMoV511
1.7755 GS-45CrMoV104
1.8070 21CrMoV511 35NiCr9
1.8509 41CrALMo7 SACM645 40CAD6,12 905M39 41CrAlMo7 2940 41CrAlMo7
1.8523 39CrMoV139 897M39 36CrMoV12
1.2311 40CrMnMo7 35CrMo8KU
1.4882 X50CrMnNiNbN219 Z50CMNNb21.09
1.5864 35NiCr18
High-Alloy Steel, Cast Steel
1.2343 X38CrMoV51 H11 Z38CDV5 BH11 X37CrMoV51KU X37CrMoV5 SKD6
1.2344 X40CrMoV51 H13 Z40CDV5 BH13 X40CrMoV511KU 2242 X40CrMoV5 SKD61
1.2379 X155CrVMo121 D2 Z160CDV12 BD2 X155CrVMo121KU SKD11
1.2436 X210CrW12 X215CrW121KU 2312 X210CrW12 SKD2
1.2581 X30WCrV93 H21 Z30WCV9 BH21 X30WCrV93KU X30WCrV9 SKD5
1.2601 X 165CrMoV12 X165CrMoW12KU 2310 X160CrMoV12
1.2606 X37CrMoW 51 H12 Z35CWDV5 BH12 X35CrMoW05KU F.537 SKD62
1.5662 X8Ni9 ASTMA353 1501.509; 50 X10Ni9 XBNi09 SL9N53
1.5680 12Ni19 2515 Z18N5
1.3202 S12-1-4-5 BT15 HS12-1-5-5 12-1-5-5
1.3207 S10-4-3-10 Z130WKCDV BT42 HS10-4-3-10 SKH57
1.3243 S6-5-2-5 T15 KCV06-05-05-04-02 HS6-5-2-5 2723 6-5-2-5 SKH55
1.3246 S7-4-2-5 Z110WKCDV07-05-04 HS7-4-2-5 7-4-2-5 M35
1.3247 S2-10-1-8 Z110DKCWV09-08-04 BM42 HS2-9-1-8 2-10-1-8 M41 SKH51
1.3249 S2-9-2-8 M42 BM34 2-9-2-8
1.3343 S6-5-2 M35 Z85WDCV BM2 HS6-5-2-5 2722 SKH9; SKH51
Stainless Steel, Cast Steel
1.4000 X6Cr13 403 Z6C13 403S17 X6Cr3 2301 F.3110 SUS403
Werkstoff Germany U.S.A. France Great Britain Italy Sweden Spain Japan
No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS
1.4001 X6Cr14 F.8401 410S, 429
1.4002 X6CrAl13 405 Z8CA12 405S17 X6CrAl13 SUS405
1.4006 (G-)X10Cr13 SUS410 Z10C13 410S21 X12Cr13 2302 F.3401 SUS410
1.4016 X8Cr17 430 Z8C17 430S15 X8Cr17 2320 F.3113 SUS430
1.4021 X20Cr13 420 Z20C13 420S37 X20Cr13 2303 SUS420J1
1.4027 G-X20Cr14 Z20C13M 420C29 SCS2
1.4086 G-X120Cr29 452C11
1.4104 X12CrMoS17 430F Z10CF17 441S29 X10CrS17 2383 F.3117 SUS430F
1.4113 X6CrMo17 434 Z8CD1701 434S17 X8CrMo17 2325 SUS434
1.4340 G-X40CrNi274
1.4417 X2CrNiMoSi195 S31500 2376
1.4720 X20CrMo13
1.4724 X10CrA113 405 Z10C13 403S17 X10CrA112 F.311 SUS405
1.4742 X10CrA118 430 Z10CAS18 430S15 X8Cr17 F.3113 SUS430
1.4762 X10CrA124 446 Z10CAS24 X16Cr26 2322 SUH446
1.4034 X46Cr13 Z40CM 420S45 X40Cr14 2304 F.3405
1.4057 X20CrNi17 431 Z6CNi6.02 431S29 X16CrNi16 2321 SUS431
1.4125 X105CrMo17 Z100CD17 X 105CrMo17 SUS440C

Stainless Steel and Cast Iron

Werkstoff Germany U.S.A. France Great Britain Italy Sweden Spain Japan
No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS
Austenitic Stainless Steel
1.4301 X5CrNi189 304 Z6CN18.09 304S15 X5CrNi1810 2332 F.3551 SUS304
1.4310 X12CrNi177 301 Z12CN17.07 301S21 X2CrNi1807 2331 F.3517 SUS301
1.4311 X2CrNiN1810 304LN Z2CN18.10 304S62 X2CrNiN1810 2371 SUS304LN
1.4312 G-X10CrNi188 Z10CN18.9M 302C25
1.4350 X5CrNi189 304 Z6CN18.09 304S31 X5CrNi1810 2332/2333 F.3551
1.4362 X2CrNiN234 S32304 Z2CN23-04AZ 2327
1.4401 X5CrNiMo17122 316 Z6CND17.11 316S16 X5CrNiMo1712 2347 F.3543 SUS316
1.4404 X2CrNiMo1810 316L Z2CND17.12 316S12 X2CrNiMo1712 2343/2348/2553 SUS316
1.4410 G-X10CrNiMo189 Z5CND20.12M
1.4429 X2CrNiMoN17133 316LN Z2CND17.13 316S63 X2CrNiMoN1713 2375 SUS316LN
1.4435 X2CrNiMo18143 316L Z2CND17.12 316S13 X2CrNiMo1712 2353 SCS16
1.4436 X5CrNiMo17133 316 Z6CND18-12-03 316S33 X8CrNiMo1713 2343/2347 SUS316
1.4438 X2CrNiMo18164 317L Z2CND19.15 317S12 X2CrNiMo1816 2367 SUS317L
1.4500 G-X7NiCrMoCuNb2520 23NCDU25.20M
1.4541 X10CrNiMoTi1810 321 Z6CNT18.10 321S12 X6CrNiTi1811 2337 F.3553F.3523 SUS321
1.4550 X10CrNiNb 347 Z6CNNb18.10 347S17 X6CrNiNb1811 2338 F.3552F.3524 SUS347
1.4552 G-X7CrNiNb189 Z4CNNb19.10M 347C17
1.4571 X10CrNiMoTi1810 316Ti Z6NDT17.12 320S17 X6CrNiMoTi1712 2350 F.3535 SUS316TI
1.4583 X10CrNiMoNb1812 318 Z6CNDN1713B X6CrNiMoNb
1.4585 G-X7CrNiMoCuNb1818 X6CrNiMoTi1712
1.4828 X15CrNiSi2012 309 Z15CNS20.12 309S24 SUH309
Werkstoff Germany U.S.A. France Great Britain Italy Sweden Spain Japan
No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS
1.4845 X12CrNi2521 310S Z12CN2520 310S24 X6CrNi2520 2361 F.331 SUH310; SUS310S
Austenitic/Ferritic Stainless Steel (Duplex)
1.4460 X8CrNiMo275 S32900 2324 SUS329J1
1.4462 X2CrNiMoN2253 Z2CND22-05-03 2977
1.4821 X20CrNiSi254 Z20CNS25.04
1.4823 G-X40CrNiSi274
Gray Cast Iron
0.6010 GG10 CLASS20 Ft10D G10 110 FC100
0.6015 GG15 CLASS25 Ft15D GRADE150 G15 115 FG15 FC150
0.6020 GG20 CLASS30 Ft20D GRADE220 G20 120 FG20 FC200
0.6025 GG25 CLASS35 Ft25D GRADE260 G25 125 FG25 FC250
0.6030 GG30 CLASS45 Ft30D GRADE300 G30 130 FG30 FC300
0.6035 GG35 CLASS50 Ft35D GRADE350 G35 135 FG35 FC350
0.6040 GG40 CLASS55 Ft40D GRADE400 140 FC400
Gray Cast Iron with Nodular Graphite
0.7033 GGG35.3 0717-15 FCD350
0.7040 GGG40 60-40-18 FCS400-12 SNG420/12 GGG40 0717-02 GGG40 FCD400
0.7043 GGG40.3 FGS370-17 SNG370/17 0717-12 FCD400
0.7050 GGG50 80-55-06 FGS500-7 SNG500/7 GGG50 0727-02 GGG50 FCD500
0.7060 GGG60 FGS600-3 SNG600/3 GGG60 0732-03 GGG60 FCD600
0.7070 GGG70 100-70-03 FGS700-2 SNG700/2 GGG70 0737-01 GGG70 FCD700
White malleable Cast Iron
0.8040 GTW-40 MB40-10 W410/4 GMB40 GTW40
0.8045 GTW-45 GMB45 GTW45
0.8055 GTW-55 GTW55
0.8065 GTW-65 GTW65
0.8135 GTS-35 32510 MN35-10 B340/12 810 GTS35
0.8145 GTS-45 40010 P440/7 852 GTS45
0.8035 GTW-35 MB35-7 W340/3 GTW35
0.8155 GTS-55 50005 MP50-5 P510/4 854 GTS55
0.8165 GTS-65 70003 MP60-3 P570/3 856 GTS65
0.8170 GTS-70 90001 M870-2 P690/2 0862; 0864 GTS70

Werkstoff Germany U.S.A. France Great Britain Italy Sweden Spain Japan
No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS
Non-Ferrous Materials
Aluminium Alloys
3.0255 Al99.5 1000 A59050C L31/34/36
3.3315 AlMg1
3.1655 AlCuSiPb
3.1754 G-AlCu5Ni1,5 3.4345 AlZnMgCu0,5 AZ4GU/9051 L86 811-04 7050
3.2373 G-AlSi9Mg
3.2381 G-AlSi10Mg
3.2382 GD-AlSi10Mg
Werkstoff Germany U.S.A. France Great Britain Italy Sweden Spain Japan
No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS
3.2383 G-AlSi10Mg (Cu) A360.2 LM9 4253
3.2383 GK-AlSi10Mg (Cu) A360.2 LM9 4253
3.2581 G-AlSi12 A413.2 LM6 4261
3.2582 GD-AlSi12 A413.0 4247 A6061
3.2583 G-AlSi12 (Cu) A413.1 LM20 4260 ADC12
3.3561 G-AlMg5 GD-AlSi12 A-SU 12 LN5 4252 AC4A
3.5101 G-MgZn4SE1Zr1 ZE41 G-Z4TR MAG5
3.5103 MgSE3Zn2Zr1 EZ33 G-TR3Z2 MAG6
3.5106 G-MgAg3SE2Zr1 QE22 G-Ag22,5 MAG12
3.5812 G-MgAl8Zn1 AZ81 G-A9 MAG1
3.5912 G-MgAl9Zn1 AZ91 G-A9Z1 MAG7
2.1871 G-AlCu4TiMg
3.2371 G-AlSi7Mg 4218B
Copper Alloys
2.1090 G-CuSn7ZnPb C93200 U-E7Z5Pb4
2.1096 G-CuSn5ZnPb C83600 U-E5Pb5Z5 LG2
2.1098 G-CuSn2ZnPb
2.1176 G-CuPb10Sn C93700 U-E10Pb10 LB2
2.1182 G-CuPb15Sn C93800 U-Pb15E8 LB1
2.0240 CuZn15 C23000 CuZn15 CZ102
2.0265 CuZn30 C26000 CuZn30 CZ106
2.0321 CuZn37 C27200, C27700 CuZn36, CuZn37 CZ108 C2700,C2720
2.0592 G-CuZn35Al1 C86500 U-Z36N3 HTB1
2.0596 G-CuZn34Al2 C86200 U-Z36N3 HTB1
2.1188 G-CuPb20Sn C94100 U-Pb20 LB5
2.1292 G-CuCrF35 C81500 CC1-FF
2.1293 CuCrZr C18200 U-Cr0,8Zr CC102
2.0966 CuAl10Ni5Fe4 C63000 U-A10N Ca104
2.0975 G-CuAl10Ni B-148-52
2.1050 G-CuSn10 C90700 CT1
2.1052 G-CuSn12 C90800 UE12P Pb2

High-Temp Alloys

Werkstoff Germany U.S.A. France Great Britain US Sweden Spain Japan

No. DIN AISI/SAE UNS AFNOR BS US Trade Designation SS UNE JIS
Super-Alloys Fe-based
1.4558 X2NiCrAlTi3220 N08800 NA15 Incoloy 800
1.4562 X1NiCrMoCu32287 N08031
1.4563 X1NiCrMoCuN31274 N08028 Z1NCDU31.27
1.4864 X12NiCrSi 330 Z12NCS35.16 SUH330
1.4864 X12NiCrSi3616 N08330 Z12NCS35.16 NA17 SUH330
1.4958 X5NiCrAlTi3120
1.4977 X40CoCrNi2020 Z42CNKDWNb
Werkstoff Germany U.S.A. France Great Britain Italy Sweden Spain Japan
No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS
S66286 A-286
S41800 Greek Ascoloy
R30556 Haynes 556 (HS556)
R30155 N155
Super-Alloys Co-based
R30188 Haynes 188
R30605 L605 (Haynes 25)
MARM-302, 322, 509
Stellite 6, 21, 31
Super-alloys Ni-based
2.4360 NiCu30Fe NU30 NA13 Monel 400
2.4610 NiMo16Cr16Ti Hastelloy C-4
2.4630 NiCr20Ti N06075 NC20T HR5, 203-4 Nimonic 75
2.4642 NiCr29Fe NC30Fe Inconel 690
2.4810 G-NiMo30 N10276 Hastelloy C
2.4856 NiCr22Mo9Nb N06625 NC22FeDNb NA21 Inconel 625
2.4858 NiCr21Mo N08825 NC21FeDU NA16 Incoloy 825
2.4375 NiCu30 Al NU30AT NA18 Monel K-500
2.4668 NiCr19FeNbMo N07718 NC19FeNb Inconel 718
2.4669 NiCr15Fe7TiAl N07750 NC15TNbA Inconel X-750
2.4685 G-NiMo28 N10001 Hastelloy B
2.4694 NiCr16Fe7TiAl N00751 Inconel 751
Titanium and titanium alloys
3.7025 Ti 1 R50250 2TA1
3.7124 TiCu2 2TA21-24
3.7195 TiAl3V2.5
3.7225 Ti1Pd R52250 TP1
3.7115 TiAl5Sn2
3.7145 TiAl6Sn2Zr4Mo2Si R54620
3.7165 TiAl6V4 R56400 T-A6V TA10-13; TA28 TiAl6V4
3.7175 TiAl6V6Sn2 R56620 Ti6V6Al2Sn
3.7185 TiAl4Mo4Sn2 TA45-51; TA57

Hardened Materials

Werkstoff Germany U.S.A. France Great Britain Italy Sweden Spain Japan
No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS
White Cast Iron
0.9620 G-X260NiCr42 Ni- Hard 2 Grade 2A 0512-00
0.9625 G-X330NiCr42 Ni- Hard 1 Grade 2B 0513-00
0.9630 G-X300CrNiSi952 Ni- Hard 4
0.9635 G-X300CrMo153
Hardened Cast Iron
0.9640 G-X300CrMoNi1521
 Werkstoff Germany U.S.A. France Great Britain Italy Sweden Spain Japan
No. DIN AISI/SAE UNS AFNOR BS UNI SS UNE JIS
0.9645 G-X260CrMoNi2021
0.9650 G-X260Cr27 A532IIIA25%Cr Grade 3D 0466-00
0.9655 G-X300CrMo271
0.9655 G-X300CrMo271 A532IIIA25%Cr Grade 3E
copyright 2010 maryland metrics Data courtesy of Kennametal