Scribd
Upload
122 views

Slide Deck 1-DC Analysis

This document contains tutorial problems for a basic electrical and electronics engineering course. It covers various circuit analysis techniques including nodal analysis, mesh analysis, Thevenin's and Norton's theorems, superposition, and source transformations. Example circuits are provided for students to practice finding resistances, voltages, currents, powers and applying analysis methods like nodal analysis, mesh analysis and equivalent circuit theorems. Solutions are provided for 17 practice problems applying these analysis techniques to determine values for various elements in each circuit.

Uploaded by

Prithviraj Netke
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
122 views

Slide Deck 1-DC Analysis

This document contains tutorial problems for a basic electrical and electronics engineering course. It covers various circuit analysis techniques including nodal analysis, mesh analysis, Thevenin's and Norton's theorems, superposition, and source transformations. Example circuits are provided for students to practice finding resistances, voltages, currents, powers and applying analysis methods like nodal analysis, mesh analysis and equivalent circuit theorems. Solutions are provided for 17 practice problems applying these analysis techniques to determine values for various elements in each circuit.

Uploaded by

Prithviraj Netke
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

EN-209: Basic Electrical and Electronics Engineering TUTORIAL-I

(DC Circuit Analysis and Theorems)

1. Find the equivalent resistance between the terminals A and B

(a) (b)

[Ans: (a) 2Ω, (b) 3Ω]

2. If VA – VB = 6 V, then VC – VD is

[Ans: -5 V]

3. Use nodal analysis to find v1, v2 and v3 in the circuit shown in the figure below

[Ans: v1 = 10 V, v2 = 4.933 V, v3 = 12.267 V]

IIT BOMBAY
EN-209: Basic Electrical and Electronics Engineering TUTORIAL-I
(DC Circuit Analysis and Theorems)

4. Obtain the Thevenin and Norton equivalent circuits at terminals a-b for the circuit in Fig. below

[Ans: 10 Ω, Vth = 166.67 V, IN = 16.667 A]

5. Find the Thevenin equivalent between terminals a-b of the foloowing circuits,

(a) (b)

[Ans: (a) Vth = 2V, Rth = 16.67 Ω. (b) Vth = -1.5 V, Rth = 2 Ω]

6. Use mesh analysis to find the current I in circuit (a) below, io and vo in circuit (b) below, and i1, i2
and i3 in circuit (c) below. All resistances in Ω if it is not mentioned.

(a) (b) (c)

[Ans: (a) I= 0.375 A. (b): vo =2.9406 V, io =490 mA. (c): i1=3.5 A, i2=-0.5 A and i3=2.5 A]

IIT BOMBAY
EN-209: Basic Electrical and Electronics Engineering TUTORIAL-I
(DC Circuit Analysis and Theorems)

7. For the circuit shown in the figure below, what resistor connected across terminals (ab) will
absorb maximum power from the circuit? What is that power?

[Ans: 8 kΩ, 1.152 W]

8. Find the Nortons equivalent at terminals a-b of the circuit in the Fig. below

[Ans: RN= 3 Ω, IN = 1A]

9. Use superposition to find Vx in the circuits (a & b) , and vo and io in circuit (c).

(a) (b)

(c)

IIT BOMBAY
EN-209: Basic Electrical and Electronics Engineering TUTORIAL-I
(DC Circuit Analysis and Theorems)

[Ans: (a) 11.2 V. (b): -26.67 V. (c) 17.99 V, 1.799 A]

10. Use source transformation to find the voltage vx in circuits (a&b) and ix in circuits (c&d).

(a) (b)

(c) (d)

[Ans: (a&b) 2.978 V. (c) 254.8 mA, (d) 1.6 A]

11. Find vX and iX in the circuit

[Ans: -4 V, 2.105 A]

12. Apply node voltage analysis to find io and the power dissipated in each resistor in the circuit

[Ans: i0 = 2.73 A, P6 = 44.63 W, P3 = 0.333 W, P5 = 3.8 W]

IIT BOMBAY
EN-209: Basic Electrical and Electronics Engineering TUTORIAL-I
(DC Circuit Analysis and Theorems)

13. For the circuit in the Figure, Suppose Vin = 20 V.

(a) Find the output voltage and output current.

(b) Find the ratio of output voltage to input voltage.

(c) Find the power delivered by each source (dependent & independent sources)

[Ans: (a) 100 V, 20 A; (b) 5; (c) 100 W (VS), 150 W (DVS), 2000 W (DCS)]

14. (a) For the circuit shown in the Fig. obtain the Thevenins equivalent at terminals a-b

(b) Calculate the current in RL = 8Ω

(c) Find the value of RL for maximum power to be


deliverable to load

(d) Determine the maximum power.

[Ans: (a) 12 ohm, 40 V; (b) 2 A; (c) 12 ohm; (d) 33.33 W]

15. Determine the mesh currents in the circuit

[Ans: I1 = -3.26 mA, I2 = -1.99 mA, I3 = 1.82 mA]

IIT BOMBAY
EN-209: Basic Electrical and Electronics Engineering TUTORIAL-I
(DC Circuit Analysis and Theorems)

16. In the circuit shown below, the maximum power transferred to the resistor R is

[Ans: 3.025 W]

17. Calculate the node voltages v1, v2, and v3 in the circuit (a) and the voltage VA in circuit (b)

(a) (b)

[Ans: (a) v1 = -7.19 V, v2 = -2.78 V, v3 = 2.89 V, (b) VA=11.42 V]

IIT BOMBAY

You might also like