International Journal of Science and Engineering Applications

Volume 7–Issue 07,125-129, 2018, ISSN:-2319–7560

Modelling and Control of Quadrotor Control System

using MATLAB/Simulink

Wai Mar Thet Myo Myint Ei Ei Khin

Department of Electronics Department of Electronics Department of Electronics
Engineering Engineering Engineering
Technological University Technological University Technological University
Thanlyin, Myanmar Thanlyin, Myanmar Thanlyin, Myanmar

Abstract: Generally, Quadrotor type Unmanned Aerial Vehicles are unstable in nature, so to stabilize it, the controller is used. This
paper observes the PD controller that make use of UAV to control the adjust of quadrotor UAV even as in the air. The gain parameters
of the PD controller, the proportional gain Kp and the derivative gain Kd are apply to be stable and good performance. Unmanned aerial
vehicles (UAV) are becoming increasingly common and span a huge range of size and shape. After integrating PD controllers into the
systems, quadcopter settling time of roll, pitch and yaw system. Simulations result and comparison of X, Yand Yaw control techniques
are presented at the end of this paper. This controller monitors the controlled process variable, and compares it with the reference or set
point. The difference between actual and desired value of the process variable, called the error signal. Error is applied as feedback to
generate a control action to bring the controlled process variable to the same value as the set point. Control action in which the output
is proportional to a linear combination of the input and the time rate of change of input.

Keywords: stabilization; integrating; simulations result and comparison; error signal; control action

speed of each propeller and the attitude stabilization can be

1. INTRODUCTION achieved by controlling the required speed of each motor.
UAVs or ‘Unmanned Aerial Vehicles’ are defined as aircrafts UAVs can be remotely controlled or flown autonomously
without the onboard presence of pilot. Research and based on pre-programmed flight plans. Hence, plenty of
development of unmanned aerial vehicle (UAV) are getting research has been done with regards to control techniques for
high encouragement nowadays, since the application of UAV the trajectory tracking of the flight plans. Nowadays, one of
can apply to variety of area such as rescue mission, military, the most popular UAV type is the rotary fixed-wing UAV.
film making, agriculture and others. For search and rescue They are highly lauded due to the advantages they have, such
mission, UAV that attached with infrared cameras assist the as; vertical take-off and landing ability, portability, good
mission to search the target. Quadcopter or quadrotor aircraft mobility, ability to carry payload, and also the ability to
is one of the UAV that is major focuses of active researches in operate in constraint spaces. The main contribution of this
recent years. Quadcopter operated by thrust that produce by paper is to introduce a new based PD control algorithm for
four motors that attached to it body. It has four input force and attitude stabilization of Quad-rotor UAV. It is worth to
six output states (x, y, z, θ, ψ, ω) and it is an under-actuated mention that the proposed algorithm was implemented and
system, Quadcopter has the advantages over the conventional tested on developed Quadrotor UAV system and compared
helicopter where the mechanical design is simpler. UAVs are with conventional PD Controller.
usually used for activities which are deemed to be either too
dull, dirty or dangerous for humans, and as a result, eliminates
the risk of loss of human life for certain applications [1]. 2. MODELLING OF A QUADROTOR
UAVs can be remotely controlled or flown autonomously
based on pre-programmed flight plans. Hence, plenty of
2.1 Aerodynamics Forces and Torques
research has been done with regards to control techniques for Quadrotor needs a mechanism for generating forces and
the trajectory tracking of the flight plans. Quadrotors are now torques that are required to control its horizontal and vertical
widely available, both as commercial products and as open- movements. There are four main forces that exert on a
source projects. Usually UAV systems are unstable and quadrotor: gravity, lift, thrust and drag. Gravity is a force that
stabilization control plays a very important role in it. It pulls the quadrotor down because of its mass. Lift and thrust
automatically stabilizes the attitude of the vehicle and are the upward reaction forces acting on quadrotor due to the
prevents the vehicle from flopping and also maintains the propellers. Finally, drag is the backward force on the
desired orientation during flight. The Quadrotor UAV quadrotor due to air. Quadrotor mechanism is mainly based on
stabilization is depend upon the appropriate controlling of its rotors and propellers that generate thrust perpendicular to
their four motor speed. A stable flight is necessary for safety its rotor. The main thrust is generated along Z axis that creates
and for better flight experience and to achieve a successful vertical movement. The horizontal movements along X and Y
mission. The four rotors are used in controlling the vehicle. axes are resulted from directing the force or thrust vector in
Each rotor produces moments as well as vertical forces. These the appropriate direction. Therefore, quadrotor can be
moments have been experimentally observed. The flight characterized by one main control force T b uF, collective lift
movement of quad-rotor UAV is controlled by varying the u is the sum of the thrust generated by the four propellers.

www.ijsea.com 125
 International Journal of Science and Engineering Applications
Volume 7–Issue 07,125-129, 2018, ISSN:-2319–7560

Where l is distance from the propellers to the center of mass clockwise direction while the other pair of motors (2, 4)
of the quadrotor and Q is the fan torques due to air. rotates in clockwise direction as shown in fig. The motion of
The collective lift u is the sum of the thrust generated by the quadrotor is achieved by varying the motor speed. Thus,
four propellers. increasing or decreasing the four motor's speeds together
generates vertical motion. Increasing motor (1, 2) speed or
motor (3, 4) speed produces roll rotation that results quadrotor
to bend left or bend right. The same method is used for pitch
(1) control. Varying motors (1,4) and motors (2,3) speed
conversely produce pitch rotation that results quadrotor to go
Torque produced by each axis is resulted from forward or backward. Yaw rotation can be done by the
difference in the counter-torque between each pair of motors.
(2)

(3)

(4)

Where b is distance from the propellers to the center of mass

of the quadrotor and Q is the fan torques due to air drag.
, and are the roll, pitch and yaw
angular velocity that can be received from gyro sensor. The
error values will be

(5)

(6)
Figure 1. Quadrotor concept motions description
(7)

3. CONVENTIONAL PD CONTROLLER
where rollde , pitchde and yawde Proportional-plus-derivative(PD) controllers are widely used
represent desired angular velocity. Using these in the industry [2,3]. The main reason is its relatively simple
structure, which can be easily understood and implemented in
error values in PD equation, it can be gained practice [4]. The widespread use of PD-type controllers in
industries has affected efforts in the design and tuning of
conventional PD controllers so as to achieve an optimal
performance for the control system [5] The quadrotor in
(8) nature is very unstable. In order to stabilize the quadrotor, PD
controller is needed to be developed within the system. PD
controller is the most widely used controller because of its
(9) simplicity and robustness. The mathematical equivalent of PD
control algorithm can be expressed as

(10)
(11)
Where kp and kd are the proportional, and derivative gains
respectively. To achieve stabilization, three PD controllers are
2.2 Quadrotor Configuration implemented for three different axes: roll, pitch and yaw
Quadrotor UAV can be assigned to two different respectively. For a sensor feedback, we use gyro sensor which
configurations; plus, and cross configuration. In this case, four is three axes angular rate sensor.
brushless DC motors are mounted on quadrotor UAV in cross
configuration. One pair of motors (1, 3) rotates in counter

www.ijsea.com 126
 International Journal of Science and Engineering Applications
Volume 7–Issue 07,125-129, 2018, ISSN:-2319–7560

4. IMPLEMENTATION OF SIMULINK

Figure 2. Block Diagram of Simulation Figure 3. The trajectory of UAV without changing P

This figure contains yaw control, high control, velocity

control, attitude control. Firstly, the velocity control of
proportional gain is 0.1 and derivative gain is 2. The High
control of proportional gain is 4 and derivative gain is 1. The
altitude control of proportional gain is 100 and derivative gain
is 1. The yaw control of proportional gain is 20 and derivative
gain is 2. The simulation result of desired value and actual
value as shown in figure 4. The error value x, y and yaw as
shown in figure 5. And then, this velocity, high, altitude and
yaw control with proportional gain is changing and the
derivative is not changing this result of desired and actual
value as shown in figure 7, and the error value of x, y and yaw
as shown in figure 8.

5. SIMULATION RESULT
The simulation result is the compared of desired and actual
value and error without changing P and with changing P. The
changing of P is high the error is high. The greater the value
of P, the higher the error becomes. This paper states the result
of this desired and actual error of X, Y and Yaw.

Table 1. PD gain values for without changing P

Type kp kd
Velocity Control 0.1 2
High Control 4 1
Altitude Control 100 1
Yaw Control 20 2
Figure 4. Plot of desired & actual value of X, Y & Yaw

www.ijsea.com 127
 International Journal of Science and Engineering Applications
Volume 7–Issue 07,125-129, 2018, ISSN:-2319–7560

Figure 5. Plot of error in X, Y & Yaw without changing P

Table 2. PD gain values for with changing P

Type kp kd Figure 7. Plot of desired & actual value of X, Y & Yaw

Velocity Control 0.2 2
High Control 8 1
Altitude Control 200 1
Yaw Control 40 2

Figure 6. The trajectory of UAV with changing P Figure 8. Plot of error in X, Y & Yaw with changing P

www.ijsea.com 128
 International Journal of Science and Engineering Applications
Volume 7–Issue 07,125-129, 2018, ISSN:-2319–7560

6. CONCLUSION 8. REFERENCES
Unmanned aerial vehicles (UAV) can provide a critical [1] Comparison of Backstepping, Fuzzy-PID, and PID
support for search and rescue operations. However, in order to Control Techniques using X8 model in relation to A*
achieve their full potential, it is necessary to properly account Path Planning Yi Zhou Singapore Institute of
for all the parameters that can affect the flight of the UAVs Technology , Singapore.
such as quality of sensory operations (that can depend on the [2] K. J. Astrom and T. Hagglund, “Automatic Tuning of
position of the UAVs for instance), energy constraints, Regulators with Specifications on Phase and Am- plitude
environmental hazards or data sharing constraints between Margins,” Journal of Automatica, Vol. 20, No. 5, 1984,
UAVs and rescue teams. pp. 645-651. doi:10.1016/0005-1098(84)90014-1.
This paper presented the design of a PD controller algorithm
to control the quadrotor system. The simulation result of the [3] W. K. Ho, O. P. Gan, E. B Tay and E. L. Ang, “Perform-
desired value and actual value of X,Y and Yaw compared ance and Gain and Phase Margins of Well-Known PID
without changing PD and with changing PD controller .Also Tuning Formulas,” IEEE Transactions on Control
the compared of this result can be improved by using others System Technology.
features. [4] Q. G. Wang, T. H. Lee, H. W. Fung, Q. Bi and Y. Zhang,
“PID Tuning for Improved Performance,” IEEE Transac-
tions on Control Systems Technology.
7. ACKNOWLEDGMENTS
I greatly appreciate to all teachers from the Department of [5] Y. C. Cheng and C. Hwang, “Stabilization of Unstable
Electronics Engineering, Technological University (Thanlyin) First-Order Time-Delay,” Journal of the Chinese Institute
who work in Research. of Engineers.
I would like to give great thanks to Research Department of [6] D. Vrancic, S. Strmcnik, J. Kocijan and P. B. M.
Electronics Engineering, Technological University (Thanlyin) Oliveira, “Improving Disturbance Rejection of PID
for kind permission to study related on-going research Controllers by Means of the Magnitude Optimum
projects. Method,” ISA Trans- actions.

www.ijsea.com 129