KODAK UHD LED TV

User Manual
55UHDXSMART 4K | 50UHDXSMART 4K

Please read this manual carefully before installing and operating the TV.
Keep this manual with you for reference.
CONTENTS

Introduction 1

Warnings & Safety Precautions 1

Features 2

Safety Information 2

Important Safety Precautions 3

Prepration Stand Installation 4

Functional Overview Fornt & Side Panel 5

Rear Panel 6

Connections 7

Remote Control 8

Basic Operation 11

Menu Operation 12

Media Play 19

PC Setting 20

Instructions for Intelligent Platform Operation 21

Specification 25

Troubleshooting 26
 INTRODUCTION

Thank you for choosing our product. To be able to make use of all application options, we
recommend that you should read this operation manual carefully and preserve it for quick
access , if required.
Do not touch any parts in the set and do not make changes to any settings not described in
this operating manual.
The LED Screen is a high-tech product which consists of more than 9,00,000 control
elements. Any Non-active red, blue or green spots lines that might appear on the screen
occasionally, have no effect on the performance of the screen or television and may disappear
over a short period of time.

WARNINGS AND SAFETY PRECAUTIONS

Warning:
– To prevent damage to the TV which may result in a fire or electrical shock hazard, do not
expose the TV set to rain or excessive moisture.
– Do not rub or strike the Active matrix LED with any thing hard as this may scratch, mark or
damage the active matrix LED permanently.
– For safety, do not place vessels or any container which contain fluid including water, on or
near the TV.
– Do not insert any objects in the ventilation slots.
Service:
– Do not remove the back cover of the set as this can expose you to very high voltage and
other hazards. If the set does not operate properly, unplug it and call KODAK HD LED
TV customer care.

Location:
– Position the set so that no bright light or sunlight falls directly on the screen. Reflections on
the screen affects the picture quality & viewing television.
– Soft and indirect lighting is recommended for comfortable viewing.
– Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or
heat.
– Adequate ventilation is essential to prevent set failure.Ensure that the set is placed in a
position to allow a free flow of air. Do not cover ventilation opening on the back cover. Do
not place the set in an enclosure or very close to walls.
– Avoid excessively warm locations to prevent possible damages to the set.
– Place the television on a solid and flat surface, if not wall mounted.

1
FEATURES
– SMART LED TV
– Ultra HD Resolution (4K)
– Extra Slim Design
– 50000:1 Dynamic Contrast Ratio
– HDMI Connectivity
– Full Multimedia Interface
– Seven Picture Modes
– Five Sound Modes
– 178ox178o Viewing Angle
– PC Connectivity
– Dynamic Noise Reduction
– LAN & Wi-Fi Connection for Internet
– Web Browsing

SAFETY INFORMATION

CAUTION High voltages are used in the operation of

this product. To reduce the risk of electric
RISK OF ELECTRIC SHOCK shock, do not remove cover of the cabinet,
DO NOT OPEN refer for servicing to qualified service personal.

If the LED TV require any changes or coarse adjustment, electric shocks

are imminent. Do not attempt to open, contact customer support for
needed overhual.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important
operating & maintenance (servicing) instruction in the
literature accompanying the appliance.

Warning
The lightning flash with arrowhead symbol within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated dangerous voltage within the
products enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.

2
 IMPORTANT SAFETY PRECAUTIONS

- Read & keep this instruction manual.

- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
- Do not install near any heat source such as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong.
- The wide blade or third prong are provided for your safety. If the provided plug does not
fit into your outlet, protect the power cord from being walked on or pinched particularly
at plugs, socket outlets and the point where they exit from the apparatus.
- Only use attachments / accessories specified by the manufacturer.
- Use only with the bracket or table stand specified by the manufacturer or sold
with the apparatus.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
- The apparatus should be disconnected from the mains by placing the power / standby
switch in the standby position and unplugging the power cord of the appataus from the
AC main outlet.
- The socket outlet should be installed near the equipment & should be easily accessible.
- This product should never be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacture’s instructions have been adhered to.
- The apparatus should not be exposed to dripping or splashing & objects filled with liquid,
such as vases, should be placed on the apparatus.
- Do not place any sources of danger on the apparatus (e.g. liquid filled objects, lighted
candles).
- Wall or ceiling mounting - The appliance should be mounted to a wall or ceiling only as
recommended by the manufacturer.

Servicing should be carried out by qualified service personnel only. To reduce the risk of
electric shock do not perform any servicing other than that contained in the operating
instructions.

3
PREPARATION

Stand Installation

The TV base will be separated with the TV unit. You should install the base before
you use the TV unit.

- Place the TV with its font side facing down on a cushioned flat surface.

- Place the base on the hinge of TV unit, with the base direction shown under
the base. (See the picture)

- Tighten the supplied screws to fix the TV stand securely in place.

(1 Screws - Provided with TV unit)

WARNING

- The TV stand may not be securely fixed in place after repeated tightening
and loosening of screws.
- During assembling and disassembling the TV stand, please use your hand
to support it. Failing to do so may cause the TV stand to fall and result in
personal injury / damage to the product.
- After installing the TV stand, please ensure that the screws are tightened
firmly. Failure to do so may cause the TV set to tip over or damage.

4
FUNCTIONAL OVERVIEW

Front & Side Panel

1 Power Light
On Standby Mode, the light
turns red.

2 Infrared Remote Sensor

Receives the signals from the
remote control.

3 Power
Press to turn TV on or turn to
standby mode.

4 Menu
Press to display the setup menu on
the TV screen.

5 CH-, CH+
Press to select desired channels. or
press to select or adjust a menu item.

6 Vol-, Vol+
Press to select TV or all video input
modes : TV, AV, HDMI, VGA, USB.

7 Input
Press to select source of viewing.

5
FUNCTIONAL OVERVIEW

Rear Panel

USB 2
HDMI x 3
L-AUDIO-R Y / VIDEO Pb Pr
TV USB 1 COAX
USB3 IN AV2 IN

- LAN (Local Area Network)

For Internet connection

- USB
Insert USB

- HDMI input Terminal

Connect to equipment with HDMI output

- VGA(PC IN) Input Terminal

Connect to PC.

- PC / HDMI Analog Audio Input Terminal

Connect to equipment using HDMI-DVI
connection or PC with audio output.

- AV 1 & AV 2 In / YPBPR
Connect the video output jack of DVD or VCR

- Antenna Input Terminal

Connect to equipment with antenna output or
wall antenna socket.

* This image is for reference only to explain uses of various connections. Actual product
specifications may differ from the above.

6
CONNECTIONS

You can connect VCR, DVD player, set-top box, computer, game console or other
equipment to the TV. To view external source images, press to select the input
Source

source.

Connecting an AV Equipment with HDMI Connector

Connecting an AV Equipment with Composite Connector

Connecting an AV Equipment with VGA Connector

- If the external equipment has DVI output, you can connect it to the HDMI terminal using a HDMI-DVI cable.
In case of using the HDMI-DVI cable, connect analog audio signal to RGB/HDMI analog audio input terminal.
- Please refer to the user manual of the external equipment for more information on connection to the TV.
- Please disconnect all power supplies to the equipment & TV before connection.
- Compatibility of the TV set and external equipment is dependent on hardware compatibility of both.

7
REMOTE CONTROL

Installing the remote control batteries

- Open the battery cover.

- Insert batteries (2x AAA size batteries)
Place batteries with their terminals observing
the (+) & (-) indications.
- Replace the cover & press down until the lock
snaps closed. If the remote control is not used
for an extended period of time, remove the
batteries from the remote control as damage
may result due to electrolyte leakage from the
batteries.
Note: - The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
- Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type.
- Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries
according to the instructions.
- Do not dispose of batteries in a fire, danger of explosion.
- Batteries not covered under warranty.

FUNCTIONS

POWER Turns TV into STANDBY ON/OFF.

FREEZE Select to freeze the scene still on the screen.
INFO Displays present source information with details of input signal connected.
SOUND Different sound features
T.SHIFT changing between .
Settings Press to open internet set-up.
FAV+/Capture Press to switch your favorite channels under TV menu.

P - Navigates vertically Up/Down through the Menu/Sub Menus.

- To enter character/numbers in program name parameter.
P - To navigate channel Up/Down through valid channels.

- Navigates horizontally Right/Left through the Menu/Sub menus.

- To enter in Menu/Sub menus & to adjust Vol +/-.
- To navigate the letter in program name parameter.
- To select the time.
- To select Source by right arrow key.
- Increase / Decrease the value of selected items & set the
parameter On/Off.

- To enter in sub menu.

OK - Enter to edit program name parameter.
EXIT Press to exit the OSD menu

8
REMOTE CONTROL

MENU To select menu OSD window and return to upper menu.

Change to cursor mode.
VOL +/- Select to increase or decrease volume.
PA+/- Select to increase or decrease volume for power audio.
This key provides the different power saving modes. The current mode is
displayed with ecovision symbol on the screen. In audio only mode display is off
ECO Vision
& only audio is on. Press any key to exit audio only mode. Note: VOL+/-, PA+/- &
Mute can fuction even as panel is off. Note: Audio only mode is not available in
models 32” and above.

MUTE Turns sound OFF or ON

Figures 0-9 are used to directly input channel number.

YOUTUBE/NETFLIX/
Click to open these Apps directly.
HOTSTAR
BROWSER Click to open internet browser.

APPS Click to open list of Apps

M.CAST Click to connect TV through Miracast option.

- Press this key to display sub title list.

SUB TITLE - Press this key to rename channels in program edit function.

- Press this key to switch On/Off internal speaker used in TV set.

MEDIA - Press this key to swap channel in program edit function.
- Press this key to open media center.
- Press this key to switch aspect ratio.
ASPECT - Press this key to skip channel in program edit function.

- Press this key to STOP in USB mode

- Press this key to PLAY/PAUSE in USB mode

- Press this key to FAST REVERSE in USB MODE

- Press this key to FAST FORWARD in USB MODE

GOTO - Press this key to select play time position

When playing the Photo or Video or Mp3 or Text, if you select ROOT key it will stop
ROOT
/ playing & return to the current list in USB mode.
Press to open home page.

- Press this key to play the previous track.

- Press this key to play the next track.

9
REMOTE CONTROL

Power On/Off

Turning on the TV

- Plug the TV’s power cord into a wall outlet (after this step, the main unit will turn on
and enter stanby mode automatically).
- Press the (Power) button on the TV, or press the (Power) button on the remote
control. The TV will turn on.

Placing In Standby Mode

Your TV can be placed in Standby mode in order to reduce the power consumption.
The standby mode can be usefull when you wish to interrupt viewing temporarily
(during a meal, for example).
- Press the Power Button.
- To switch back on, simply press power button.

Remark: Do not leave your TV in standby mode for long periods of time. (When you
are away on holiday, for example). It is the best to unplug the set from the mains and
aerial.

Changing Programmes

Using the programme selection buttons on the remote control to change

programmes
To select a programme, press the corresponding programme selection button
remote control. For example, to select programme 8, press the “8” programme
selection button on the remote control.

Using the P+/- buttons to sequentially change programmes

Press P+/- buttons on the remote control or on the TV to sequentially seletct
the TV programmes available in you area.

Using the button to return to sequentially change programmes

To return to the previous viewed programme, press the button on the remote
control.

10
BASIC OPERATION

Power On/Off Volume Adjustment

To turn on the TV
To change the volume
- Connect the power play into the wall outlet.
The power indicator lights in red, indicating - Press V+ to increase the sound volume.
that the TV is in Standby Mode. - Press V- to decrease the sound volume.

-Press To Mute the sound

The Power indicator lights turns off & the
- Press to temporarily turn off the sound.
TV turns on.
- Press or V+ to restore the sound to
To turn off the TV previous level.

-Press - You can decrease the sound volume by pressing

The power indicator lights in red & the V- while the sound is muted.
TV turns off to standby mode.

- It takes approximately 10 sec. for the

picture to appear after the TV is turned on. On-Screen Displays (OSD) Selection
- The TV will switch to standby mode auto-
& Adjustment
matically if there is no signal input for 10 - Press “MENU” to display the main menu.
minutes. - Press to select a menu. The selected
menu page displays.
- If the TV will not be used for a long periods
- Press to set your selection.
of time, unplug the TV from the wall outlet.
- Press to choose an item on the menu
page & press to set your selection.
- Press to adjust an item value or choose
Channel Selection options.
- Press “MENU” to return to the menu, press
To select channel ”MENU” again to exit.

Press P+/- or Program Select buttons to select

the channel number directly. The OSD menu screen will be closed auto-
matically when no operation has been made
for the set OSD menu display time.
Input Source Selection
To select input “SOURCE”.

- Press to select the desired input source,

then press “enter” to enter. The selected
input source image displays.

INPUT Source : TV, AV-1, PC, HDMI , USB

11
MENU OPERATION

CHANNEL :
Auto Tunning : You can tuto tune all RF channels in ATV input source only.
ATV Manual Tunning : Channel CH1
: Color System Auto/PAL/NTSC/SECAM
: Sound System BG/DK/I/M
: Search < >
: Frequency 62.25 MHz
MENU
Program Edit : 1 S-00 ATV

O Delete G Edit Y Move B Skip

Picture : Standard / Soft / User / Vivid/Natural/Sports/Lightness
ATV Manual Tunning Contrast : 0 - 100
Brightness : 0 - 100
Hue : 0 - 100
Sharpness : 0 - 100
Saturation : 0 - 100
ECO : Off/Low/Middle/High
back Light : 0 - 100
Color Temperature : Standard / Warm / Coll
Aspect Ratio : 16:9
Image Noise
Reduction : Off/Weak/Middle/Strong
SOUND : Standard / Music / Movie / News / User
Brass : 0 - 100
Treble : 0 - 100
Balance : 0 - 100
AVC : Off / On
Surround : Off / On
SPDIF Output : PCM/RAQ/OFF
Screen Off : >>>
(Press Ok, Only Sound, No Picture
TIME :
To exit, press any key.
Date : 2016 / 7 / 1
Current Time : 09:02:40
Off Time : Setting off Time Off / On
Hour 9 (0-23)
Minute 05 (0-59)
(Off Time must be more, than 1 minutes after the current time)
On Time : Setting Boot Time OFF/ON
Hour 9
Minute 43
Source ATV
(Schedule time must behind the current time)
Sleep Time : Off / 10 min / 20 min/ 30 min/ 60 min / 90 mibn /
120 min / 180 min / 240 min.
SETTING :
Menu Time : Always / 5 Sec / 10 Sec / 15 Sec / 20 Sec / 30 Sec.
Blue Screen HDMI ECE : Off / On
: Off / On
Stand by On : OFF / ON
ARC : OFF / On
Menu Opcity : 0 - 100
Restore To Default : >>>>

12
MENU OPERATION

Channel Setting (Use for TV)

At ATV input source, the first page showed is CHANNEL. At non ATV input source, the first page
is PICTURE as default. Currently press ENTER to get in sub menu, submenu highlight fixed on
press button key, the subtopic turns up with full screen.

Channel Picture Sound Time Setting

- Press the “MENU” button on the remote
control to enter the OSD menu. Then
Auto Tuning press buttons the “CHANNEL”.
ATV Manual Tuning - Press buttons to select the desired item,
Program Edit then press or ENTER to enter.
- Press buttons on the remote control to
adjust desired item.
- Press the “MENU” button on the remote
control to return to upper menu.
Select Confirm Exit

Note : CHANNEL can be only selected under ATV condition, others can’t be used.
- Auto Scan : Enter Auto, it shows the process of frequency & the number of channels.

Press to select country & Tune Type at first,

press to select start or cancel, then press OK
button to start or exit Auto Scan.

- TV Manual Tuning:
Storage To : Current storage space shows, the following
option are available : 1-200.
System : Default option depends on country selection.
The following option are available : BG, I, DK
Current CH : Current channel shows.
Search : Can be searched at full channel condition.
Frequency : Show the current frequency & follow
search or Fine-Tune to adjust.

NOTE : After tuning by hand, make sure to press red button for storage, otherwise all channels searched
would not be stored after switching condition.

13
MENU OPERATION

- Program edit :
There are 3 items in the Preference page : Skip, Type

Select : Select your channel name by moving the cursor.

Delete : Delete current channel, as follows :

Press UP/DOWN buttons to choose the channel which you want to delete, then
press RED button to delete the current channel.

GREEN Button :
Modify current channel name, only used in ATV mode.
- At normal condition, press GREEN button to enter RENAME mode.
- At RENAME Mode :
MENU : Press to exit RENAME mode, back to normal.
EXIT : Press to exit menu.
UP/DOWN : Press to switch letters, numbers or signs.
LEFT/RIGHT : Press to switch left & right, can select by circle.
GREEN : Press to exit RENAME mode, return normal condition.

Yellow Button :
Channel switching function, ATV available as default.
- At normal condition, enter SWAP mode, & current selected channel is mobile channel X.
- At SWAP mode :
MENU : Press to exit SWAP mode, turn to normal condition.
EXIT : Press to exit menu.
UP/DOWN : Choose switch channels.
YELLOW : If current selected channel is what selected before X, no any other action,
Otherwise, the current channel is channel Y, need to exchange X& Y condition. But the
channel number stays 1,2,3,...... order as before.
BLUE Button :
Choose if skip the channel when CH+/- channel tuning.
At Non Skip channel, press BLUE button, & Skip the current channel
At skip channel, press blue button to cancel skip.

14
MENU OPERATION

Picture Setting
You can adjust picture effects here, such as contrast,
brightness & etc.
- Press the “MENU” button on the remote
control to enter the OSD menu.
Then press buttons to select the “PICTURE”.
- Press button to select the desired item to enter.
- Press buttons on the remote control to adjust
desired item.
- Press the “MENU” button on the remote control
to return upper menu.

Picture Mode : Press buttons to select. The following option are available.
“Standard, Mild, User, Dynamic”
Contrast : Adjust image contrast.
Brightness : Adjust image brightness.
Color : Adjust the color saturation.
Sharpness : Adjust the sharpness level of image.
Tint : Determines the tint of the screen (This is only available with NTSC).
Color Temperature : Adjust the color temperature level of image. The following option are
available, “Normal, Warm, User, Cool”.
RED/GREEN/BLUE : Press buttons to adjust numeric size, Press MENU button to turn back
picture main menu.
Aspect Ratio : Press buttons to select, 16:9, Zoom 1, Zoom 2, Panorama, 4:3
Noise Reduction : Press buttons to select On/Off.

Color Temperature

You can select your favorite color temperature.

- Press the “MENU” button on the remote
control to enter the OSD menu. Then press
buttons to select the “PICTURE”
- Press button to select the “Color Temperature”
- Press buttons on the remote control to choose
color temp’s value.
- Press the “MENU” button on the remote
control to return to upper menu.

User : Adjust the color value.

Normal : Keep the original white color
Warm : Adjust the white color to a little bit red.
Cool : Adjust the white color to a little bit blue.

Remark : The changes you made will be stored automatically.

15
MENU OPERATION

PC Setting (Only for PC Mode)

The function only used in PC port to adjust PC position. Enter
the screen page with buttons or ENTER button.
- When input PC source, you can go to PC to set up menu.
- Press the “MENU” button on the remote control to enter
the OSD menu. Then press buttons to select the
“PICTURE SETUP” in main menu.
- You can press ENTER buttons to enter PC setup mode
after selecting PC setting , & the press buttons to
select your desired item press buttons to adjust.
- Press the “MENU” button on the remote control to
return to upper menu.
- In PC function operation will instruct more clear.

Auto Adjust : Press buttons, TV system adjust by itself, it can adjust, H position, V position, Phase & so
on that can make the image in center & display best.
H. Position : Adjust Horizontal Position of the PC Screen.
V. Position : Adjust the Vertical Position of the PC Screen.
Size : Adjust the size of the PC Screen.
Phase : When necessary, adjust the pixel phase of the picture to avoid picture interference.

Sound Setting
You can customize different sound mode to get best effect.
- Press the “MENU” button on the remote
control to enter the OSD menu. Then press
buttons to select the “SOUND”
- Press button to select the desired item
to enter.
- Press buttons on the remote control to
increase or decrease the value of desired
item.
- Press the “MENU’ button on the remote
control to return to upper menu.

Sound Mode : Press buttons to select one of the following options “Standard, Music, Movie,
Sports User”.
Treble : Adjust bass effect.
Bass : Adjust bass effect.
Balance : Adjust balance effect.
Auto Volume : (Auto volume control, when you turn on the TV, this feature allows the TV to
automatically adjust the sound output from level to the previous level of
last time when you turned off the TV) : On/Off.
Surround Sound : Select it to enter, then you can select Off or On.

16
MENU OPERATION

Time Setting
You can set the TV’s time & you should set time if you use the automatic On/Off times.

- Press the “MENU” button on the remote control to enter

the OSD menu.
Then press buttons to select the “TIME”.
Clock 09/NOV 04:19
Off Time
- Press button to select the desired item to enter.
13:57
On Time 13:58
- Press buttons on the remote control to adjust desired item.
Time Sleep Timer Off - Press the “MENU” button on the remote control to upper menu.
Auto Sleep On

Sleep Timer : Press buttons to select your desired item (Off,

240 min., 180 min., 120 min., 90 min., 60 min., 30 min., & 10 min.)

Auto Sleep : Within 10 min. there is no signal, the TV will auto sleep

Clock

- Press the “MENU” button on the remote control to enter

the OSD menu.
Then press buttons to select the “TIME”.
- Press button to select CLOCK, then press ENTER button
to enter.
- Press buttons to select the desired item.
- Press the “MENU” button on the remote control to return upper
menu.

Off Time
- Press the “MENU” button on the remote control to enter
the OSD menu.
Then press buttons to select the “TIME”.
- Press button to select Off Time, then press ENTER button to
enter.
- Press buttons to select the desired item, then press
buttons on the remote control to set the time.
- Press the “MENU” button on the remote control to return upper
menu.

17
MENU OPERATION

On Time

- Press the “MENU” button on the remote control to enter

the OSD menu.
Then press buttons to select the “TIME”.
- Press button to select On Time, then press ENTER to enter.
- Press buttons on the remote control to adjust desired item,
then press buttons on the remote control to set the time.
- Press the “MENU” button on the remote control to return to
upper menu.

Option Setting
You can adjust the OSD language, OSD Duration

- Press the “MENU” button on the remote control to enter the

OSD Language English OSD menu, then press buttons to select the “OPTION’.
OSD Duration
Blue
Off - Press button to select the desired item to enter.
Option Restore Default Off - Press button on the remote on the remote control to return
to upper menu.

OSD Lanugage : Press buttons to select the OSD language.

OSD Duration : Press buttons to select your desired item
(Off, 5S, 10S, 15S, 30S, 45S, 60S).
Blue Screen : If no signal is being received or the signal is very
weak, a blue screen automatically replaces the noisy picture
background. Press buttons to select On/Off.
Restore Factory Default : Restore the default setting.

Note : Restore factory default will clear all the programs &
passwords

18
MEDIA PLAY

Remote Contoller Media

Button Description
Stop / Playback
Play / Pause
Skip a scene or music
Go back to the previous or skip to the next
Press to select item
Press to confirm an action (For example:
ENTER copy, paste, etc.)

Media Play
When selecting the USB input mode & input your USB, you can play the USB.
There are 4 items in the preference page : PHOTO, MUSIC, MOVIE, TEXT.

Photo

Move Menu Exit Select

Note : Select the picture & press PLAY button to play after exiting music play mode.
When playing a movie you can press the “ENTER” button, then the function menu will
appear on the screen. You can select you desired item.

The supported file format of media playing:

File Type Supported File Format File Name
PHOTO BMP / JPEG / PNG .jpeg / .bmp
MUSIC WMA / Mp3 / Mp4 / AAC .mp3 / .wma
MOVIE MPEG1 / MPEG2 / MPEG4 / RM / RMVB .mpg / .dat / .vob
TEXT TXT .txt

Note : Not compatible with HDD. The file you played needs license for on external source
(customer should check this point) or it will not be played.

19
PC SETTING

Setting up your PC Software (Based on Windows)

The Windows display-setting for a typical computer are shown below. But the
actual screen on your PC will probably be different, depending upon your
paticular version of windows and your particular video card. But even if you're
actual screen looks different, the same, basic set-up information will apply in
almost all cases.

- First, click on “Control panel” on the Windows start menu.

- When the control panel window appears, click on “Appearance & Themes”
& a display dialog box will appear.
- When the control panel window appears, click on “Display” & a display dialog
-box will appear.
- Navigate to the “Setting” tab on the display dialog-box. The correct size
setting (resolution) Optimum: 1366 x 768

If a vertical-frequency option exists on your display settings dialog box, the correct value is “60” or “70 Hz”.
Otherwise, just click “Enter” & exit the dialog box.
Note : This is only a reference recommendation. Actual user connectivity features may differ and require
additional settings

INSTRUCTION FOR INTELLIGENT PLATFORM OPERATION

Basic Operations

Home 09:31 Press key on the remote control to show the home page.
ATV
- Press , key to select an application.
- Press ”OK” key to run the application.
HDMI
- Press “Return ” key to return to previous page.
Media Application
Browser
Center Mall
Special Tips
The operations in smart mode are complicated. The user can
41 NEW MESSAGE install Apps with different operation methods, & the operations
described in this manual are for reference only. Certain functions
are invalid from the remote control. For more convenient opera-
tion, please operate with USB mouse & keyboard.

Display Mode
If the signal from the system equals the standard signal mode, the screen is adjusted automatically. If the
signal from the system does not equal the standard signal mode, adjust the mode by referring to your
videocard user guide, otherwise there may be no video. For the display modes listed below, the screen image
has been optimized by manufacturer.

Resolution Vertical Frequency (Hz) Mode

3840 x 2160 60Hz VGA
1024x768 60Hz SVGA
1366x768 60Hz XGA
800x600 60Hz WXGA

20
INSTRUCTIONS FOR INTELLIGENT PLATFORM OPERATION

Quick Start
Before using this device, please get familiar with the operations below for better experience.

Mouse Control ( not this button in the remote but an externally connected mouse)
- Click the mouse & release immediately.
- Press & hold, Click the mouse & hold for at least three seconds.
- Clicking the left mouse key has the same effect as pressing “OK” key on the remote control.
- Clicking the right mouse key the same effect as pressing “Return” key on the remote control.

Language input setting (IME)

Language : Select the system language, select Settings > IME > Language Setting, & press “OK” key.
press “ ” key to select the desired language, & then press “OK” key.
Selecting Input Method : In the smart mode, select Settings > IME > Update Input Method, &
integarted “Android Keyboard” & “Google play in Input Method”, you can also download & install third party
input method.

Setting System Time : In the smart mode, select Settings > Date & Time > Set Date & Time
Automatically from the internet, press “OK” key & the system update the clock from the network
automatically, if the TV set isn’t connected to the network, you can set the system time manually.

Screenshot : Before screen shooting, please insert the USB mass storage device into the USB interface,
& press “SCREENSHOT” key. After screen shooting, the picture are saved in the “;\Pictures\Screenshots”
folder in the USB mass storage device.

Smart Appplications
Browser : You can use the browser to show the text, video, audio & other information on the Internet. Before
accessing the Internet, please connect the internet, please connect your TV set to the internet refer to
“ Settings > Manage Networks” for details

1. Back to the previous webpage 5. Close the current webpage window 9. Input option of URL
2. Go forward to the next webpage 6. Add a new webpage window 10. Menu option of browser
3. Refresh the webpage 7. Input box for URL 11. Option for viewing bookmark
4. Webpage window of the browser 8 Option for adding a bookmark
- How to access web address? press key to select the address bar, & type the web address in the
address bar, then select icon in the input method, & press “OK” key to access the web address.
- How to save a page in the Bookmarks? Select the icon the browser interface, & press “OK” key to enter
the browser tab & web address. Select Account, & press “OK” key. Press ” ” key to select the account for
storage, & then press “OK” key. Select OK, & then press “OK” key to add the bookmark.
- How to copy & paste the text in the web page? Place the cursor on the text to copied, press & hold the left
mouse key. When the pair of selecting cursors appears on the screen, drag the cursor to select the text.
Select copy on the screen, & click the left mouse key. Select the target position, press & hold the left mouse
key. Select the taget position, press & hold the left mouse key, & click Paste in the popup dialog box.

21
INSTRUCTIONS FOR INTELLIGENT PLATFORM OPERATION

Play the previous video. Playing setup, show/hide subtitle &

Select the speed of fast rewind adjust the audio progress in this option.
Pause / Play the video Set A-B repeat playing, set point A & point
Select the speed of fast forward B, & the video will repeat between A & B.
Play the next video A dual-screen display, start or off dual
Select the starting time point of watching display function.
View the playing list Select playing screen.
Show details of the video Select dual display window display mode.

While playing press “OK” key to show the menu options as in the picture above, select an icon & press
“OK” key to perform the operation, you can press “Return” key to exit playing, or “ ” keys
on the remote control to perform shortcut operation.

Settings
Manage Networks : In smart mode, select Network in settings, & press “OK” key to enter.
- Ethernet Setting : Before using wired network, connect one end of the network cable to the network interface of the
TV set & connect the other end to the router.
- Select Ethernet Setting & press “ ” key to enter.
- If the router setting enables obtaining IP address automatically, select The Automatic Acquisition IP
Address, press “OK” key & your TV will obtain the IP address automatically. If the router disables obtaining IP address
automatically, you can connect to the network in the following steps.
- Select IPv6, & press “OK” key to enable / disable IPv6.
- Select IP Address, & assign a valid gateway for the device.
- Select Default Gateway, & assign a valid gateway for the device.
- Select First DNS & Second DNS & assign a valid DNS server address for the device.
- Select Save, press “OK” key & the system prompts setup is successful.

Wireless Setting
- Select Wireless, & press “ ” key.
- Select Wi-Fi, & press “OK” key to enable wireless network. If the scanned network has the icon, it doesn’t require
password to connect, if the scanned network has the icon, you need to enter the valid password to access the network.
- Select a network in the list & press “OK” key.
- Select passwords type the password in the input box. Select connect & press “OK” key.
- If the router setting enables obtaining IP address automatically, select The automatic acquistion IP Address, press
“OK” key & your TV will obtain the IP address automatically. If the router disables obtaining IP address automatically, you
can connect to the network in the following steps.
- Select IP address, & assign a valid IP address for the device.
- Select Subnet Mask & assign a valid subnet mask for the device.
- Select Default Gateway & assign a valid gateway for the device.
- Select First DNS & Second DNS & assign a valid DNS server address for the devices.
- Select Save, press “OK” key & the system prompts setup is successful.

PPPOE
In this option, connect the TV set to ADSL modem directly through network cable & network dial-up
can be achieved without router adaption.
- Select PPPOE & press “OK’ key.
- Enter the username acquired from the network operator.
- Enter password acquired from the network operator.
- Select Dialup & press “OK” key.

22
INSTRUCTIONS FOR INTELLIGENT PLATFORM OPERATION

Multimedia Player
In smart mode, select Multimedia in the main interface, & press
“OK” key to run. Select the file type from all, picture, song &
video in the left.

Playing files in local disk device :

Before playing files in the local disk, insert the USB mass storage
device into the USB interface. Select local disk device in the file
directory in the center, & press “OK” key to enter. Select Back in
the directory, press “OK” key to return to previous folder. Select
the target folder, press “Return” key to return to the desktop.

Attention :
- Non standard USB devices may not be recognized. In this case, please replace with a standard USB device.
- The stream media system has certain restrictions on the format of files. The viewing may be abnormal if it is
out of the system restriction.
- Do not remove the USB device while playing or the system or device may have problem. Before replace
USB device, please turn off power supply.
- The system supports standard USB 1.1, USB 2.0, USB 3.0 devices, such as USB mass storage devices & remo-
able hard drives.
- The maximum output current of the USB port of this device is 500 mA, & self-protection will be enabled
if it is beyond this limit. Please use external power supply if an external device of higher current will be conn-
ected.
- The system is complicated, when it is reading or playing files, the screen may be still or certain functions may
be invalid due to the compatibility & stability of the USB device, in this case please turn off the device & re-
initialize the system.

Media Player UI icon introduction

Picture Player Menu Options

Play the previous picture Zoom out the picture

Pause / Play lantern slide Rotate 90o left
Play the next picture Rotate 90o right
Zoom in the picture Show detail of the picture

Play the previous track Set the repeat playing mode : All, Single, Random
Pause / resume music playing View the playing list.
Play the next track Show details of the music

Video Player Menu Options

23
 INSTRUCTIONS FOR INTELLIGENT PLATFORM OPERATION

Hotspot (Wi-Fi)
In this option, the TV set will be set as the hotspot of wireless network.
- Select WiFi Hotspot, & press “OK” key to enable this function. You need to close Wifi before you use Wifi hotspot.
- Select Config WiFi Hotspot, & press “OK” key.
- Enter the network name (SSID) in the text box, the default name is “AndroidAP”, you can also change the name.
- Select Security, & press “ ” key to select the security type, if the open network doesn’t require password,
however, any network device that scans your network can access to the Wi-Fir network, if you device scan the
open Wi-Fi network, the system will ask to enter the valid password.
- Select Display Password, & the system will assign a password automatically, or you can enter a private password.
- Select Save, press “OK” key to save the settings, & other devices in the area can scan you network when scanning
Wi-Fi network.
Remark : Please set a strong password

Backup / Update : Backup or update the device.

Remark : Before resetting, please back up your personal data, which will be lost after reset.

About : View the Models, System Version, Memory Information.

E-mail : You can log in private or business e-mail account, & receive & send e-mail.

Apk Installer : The Apk installer helps users manage applications, & allows users to install or uninstall apps in local
disk.
Note : Select Settings > Application Manager > Settings to enable/disable Allow installation of non-market
apps & set Default Installation Location, or operate All applications.
- How to install an application ? Enter Apk Installer, select install & press “OK” key to enter, Select the path of the
target installation file in local disk, locate the istallation package in the right panel, & then press “OK” key.
- How to uninstall an application ? Select manage, & press “OK” key to enter. Select the application to be removed,
& press “OK” key. Select Uninstall, click “OK” key, & the system will uninstall the application automatically.

IMPORTANT STATEMENT ON NETWORK SERVICES

All contents & services obtained from this TV set belong to the third party & are protected by laws on copyright,
patent right, trademark right and / or other intellectual property right. The said contents & services are only for your
non-commercial purposes. It is not allowed to use any content or service without the authorization of the content
owner or the service provider. Our company will undertake no liability for any direct, indirect & accidental losses or
damages caused by you or a third party’s access to any content or service or any information or any third party
software through this set under any circumstances. Third party service may be changed, deleted or stopped
without prior notice. Our company neither implies nor guarantees the continuous availability of some service or
content within any period of time. Our company is not held responsible for services related to the said service &
content. Besides, we will not bear any liability for client service. Please directly contact relevant content & service
providers if you have any problem & service request concerning relevant service or content.

24
SPECIFICATION

Screen Size 140cm

Resolution 3840 X 2160

Audio Output 10W + 10W

Power Consumption 145W

RF, AV, IN/OUT, HDMI,

Connectivity VGA, USB, EARPHONE,
YPBPR, LAN, PC, AUDIO

TV System PAL, SECAM, AUTO

AV System DK, BG, I, M

Working Voltage 100V-250V, 50/60 Hz

Screen Size 124cm

Resolution 3840 X 2160

Audio Output 10W + 10W

Power Consumption 105W

RF, AV, IN/OUT, HDMI,

Connectivity VGA, USB, EARPHONE,
YPBPR, LAN, PC, AUDIO

TV System PAL, SECAM, AUTO

AV System DK, BG, I, M

Working Voltage 100V-250V, 50/60 Hz

Note : This user manual is for reference only. Specifications are subject to change without notice.

If at any time in the future you should need to dispose of this product please note that, Waste
electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice. (Waste Electrical
& Electronic Equipment)

25
TROUBLESHOOTING

Problem Possible Causes Solutions

- The antenna connector is loose, or the - Check if the antenna plug is loose or the
Snowflake spots occur in cable damaged. cable is in good condition.
the TV images & there is - The antenna type is improper. - Check the antenna type (VHF/UHF).
noise in accompanying - The antenna direction or position is - Adjust the direction & position of the
sound. inaccurate. antenna.
- The signal is weak. - Try to use signal enhancer.
There is neither display nor - The power plug is loose or the power
- Check if the power line is connected.
sound on the screen. The supply is not connected.
- Press the “ ” button on the panel.
indication light is not on. - The power switch is not turned on.
Dotted line or strip distu- - Do not use electric hair dryer aside the
- The signal is disturbed by car, neon
rbance occurs in TV TV set & adjust the antenna direction to
light, electric hair dryer, etc..
images. reduce disturbance.
- TV singals are reflected by surrounding
- Use high oriented antenna & use the
Double images occur on high mountains or mansions.
Fine Tune function of “TV”.
the TV screen. - The direction of the antenna is
- Adjust the direction of the antenna.
inaccurate.
- Enter “PICTURE” setting to increase
The images are colorless. - The color saturation is adjusted too low.
color saturation.

The TV has no accomp- - The volume is set too low. - Adjust the volume to a proper degree.
anying sound. - The sound become mute. - Press “MUTE” key on the remote control
to cancel mute mode.
There is no display on the
PC, with the prompt of “No - The signal connecting cable is loose - Check if the signal connecting cable is
Signal Input”. The red indi- or falls off. loose or falls off. Reconnect it.
cator light is blinking.
Images displayed on the - Use automatic adjustment function.
PC deviate. The screen is - The adjustment is improper. - Enter “PC Image Mode” adjustment level
not full or is exceeded. - The display mode in inaccurate. or vertical position.
The display is fuzzy. - Use the recommended mode.
The remote control dista- - The remote control receiving window of - Remove the object to avoid blocking the
nce is short or out of the machine is blocked by some object. remote control receiving window.
control. - The battery of the remote control is low. - Replace the battery.
- Ask the network administration to obtain
- Errors occur in network parameter
available IP address & other parameters.
The browser cannot configuration.
- Check if the network connecting cable
access any link. - The network connection is improper.
is normally connected.
- Network service is not activated.
- Consult the network service provider.
- The network bandwidth is low. - Please upgrade your network bandwidth
Online video play is very - Multiple films are buffered or other files to a higher one.
slow. are downloaded at the same time. - Please try to replace with other add-
Several PCs share one network. ressed to obtain better resources.

Machine is slow, system - Too much to run the program.

- Disconnect the power supply first, &
- The external environment (such as
crash, can’t operate the connect the power supply after about
lighting, static electricity, etc.) Interfere
machine. 1-2 minutes, then turn on the TV again.
with the normal work of the machine.

26
TROUBLESHOOTING

NO PICTURE, NO SOUND BLANK SCREEN IN PC MODE

- Check if the fuse or circuit breaker is working. - Perhaps the TV can not recognize the resol-
- Plug another electrical device into the outlet ution set by he PC. Suggest to change the best
to make sure it is working or turned on. resolution of Windows system. Set refresh rate.
- Power plug is having a bad contact with the
outlet.
- Check the signal source.
SNOWY DOTS & INTERFERENCE

- If the antenna is located in a fringe area of a

NO COLOR television signal where the signal is weak, the
picture may be marred by dots. When the
- Change the color system. signal is extremely weak, it may be necessary
- Adjust the saturation. to install a special antenna to improve the
- Try another channel. Black-white program reception.
may be received. - Adjust the position & orientation of the indoor/
outdoor antenna.
- Check the connection of antenna.
REMOTE CONTROL DOES NOT WORK - Fine tune the channel.
- Try another channel. Broadcasting failure.
- Change the batteries.
- Batteries are not installed correctly.

IGNITION

NO PICTURE, NORMAL SOUND - Black spots or horizontal streaks appear or

the picture flutters or drifts. This is usually
- Adjust the brightness & contrast.
caused by interference from car ignition
- Broadcasting failure.
system, neon lamps, electric drills, or other
electrical appliance.

NORMAL PICTURE, NO SOUND

GHOST
- Press the volume up button to increase
volume. - Ghosts are caused by the television signal
- Volume is set to mute, press MUTE to restore following two paths. One is the direct path,
Audio. the other is reflected from tall buildings, hills
- Change the sound system. or other objects. Changing the direction or
- Broadcasting failure. position of the antenna. This will improve
reception.

UNORDERLY RIPPLES ON THE PICTURE

RADIO FREQUENCY INTERFERENCE
- It is usually caused by local interference,such
as cars, daylight lamps & hair driers. Adjust the - This interference produces moving ripples or
antenna to minimize the interference. diagonal streaks, & in some case, loss of cont-
rast in the picture. Find out & remove the radio
interference source.

27
www.kodaktv.in

The Kodak trademark, logo and trade dress

are used under license from Kodak

c SPPL 2018.
Super Plastronics Private Limited
B-29, 30 & 31 Sector - 81 Phase 2 Noida, 201305
Toll Free - 1800-3000-2288
[email protected]