Pages that didnt go in:54165 C&P DIVIDERS 19/3/10 15:34 Page 1

Introduction

Carpenter & Paterson Limited Software

are specialists in the design and manufacture of Pipe “Witch-Hanger”
Suspension Equipment and Fabricated Steelwork. Graphical Pipe Support Design Program
Our comprehensive service includes the supply of a
wide range of standard pipe support components. Our Engineering department is staffed by experienced
Facilities exist for the design and supply of special pipe designers who are able to give practical advice and
support fabrications and equipment in a wide range of assistance in the design of pipe support systems. We
materials and surface finishes to suit the customer’s also offer comprehensive pipe support “Site surveys”
specific requirements. including analysis of new and as built piping systems.
The Company was established in 1956 and has since All design and manufacturing systems within the
developed into one of Europe’s largest manufacturers company are controlled by formally documented
of Pipe Suspension Equipment including: systems incorporated in our Quality Assurance and
Quality Control Manuals which are based on the
Products requirements of BS EN ISO 9001.
Constant Effort Spring Units It is through this comprehensive but flexible approach,
Variable Spring Support Units based on the accuracy and reliability of our products
Ancillary Equipment (including pipe that Carpenter & Paterson Limited can provide a highly
clamps, beam clips, ‘U’ bolts, etc.) efficient service to our customers assuring that our
Pipe Whip Restraints name is synonymous with dependability and strength in
all corners of the world.
Hydraulic Shock Arrestors
Mechanical Shock Arrestors
Associated Steelwork Fabrications Standards
Cryogenic Pipe Supports Where appropriate, all dimensions of component parts
High Stiffness Rigid Struts and Clamps and material properties are in accordance with the
Witchliner Isolation Products following International Standards:-
P.T.F.E. Slide Bearings BS3974 - Pipe Supports
BS EN 13480-3-2002
A.N.S.1. B31.1 (Power(Metallic
Piping)
Industrial Piping(Petroleum
A.N.S.1. B31.3 - Part 3 Refinery Piping)
Services Design
A.S.M.E.and Calculations
Boiler and Pressure Vessel Code
Comprehensive Design of Plant
A.S.M.E. B31.1 (Power Piping)
Pipe Support Systems Components)
A.S.M.E. B31.3 (Petroleum Refinery Piping)
(Including 3D PDS/PDMS MSS. SP-58 (Pipe Hangers and Supports -
MSS. SP-58 (Pipe Hangers and Supports -
facility) Material and Design)
Material and Design)
Generation of individual support drawings MSS. SP-69 (Pipe Hangers and Supports -
MSS. SP-69 (Pipe Hangers and Supports -
Site Surveys
(Autocad R14)and Inspections Selection and Application)
Selection and Application)
Piping Systems
Site Surveys andStress Analysis
Inspections A.S.M.E. Boiler and Pressure Vessel Code
Piping Systems Stress Analysis Section 3 - Subsection N.F. (Nuclear Power Plant
Components)
RCC-M (Design and Construction -
PWR Nuclear Power Plant
Components)

04/10 III
Pages that didnt go in:54165 C&P DIVIDERS 19/3/10 15:34 Page 2

Introduction

Quality Assurance Materials

Carpenter & Paterson’s documented Quality All structural fabrications and component parts are
Assurance and Quality Control Manuals are constantly principally manufactured from high quality carbon steel,
in use and the company operate a quality management alloy steel or stainless steel.
system which complies with the requirements of BS EN A further range of low temperature steels are available
ISO 9001 to suit specialist conditions.
All incoming materials are subject to receiving control
by our Quality Assurance Department and
Comprehensive material traceability is a standard Approvals
function of our Quality Control procedures.
As part of our formally documented Quality Assurance
Surface Finishes programme, we are periodically audited by various
Within our large manufacturing area, we have in-house National and International Organisations and Main
shot blasting and surface coating facilities, thus Contractors.
ensuring a rapid turnaround for any specific customer
requirements regarding surface preparation and finish.
A large range of painting systems is available to suit all Information
types of environment and, in addition, the following
surface protections may be performed:- For more information on our Products and Services
please contact either the UK Office:
Multi-Coat Paint Finish
Hot Dip Galvanising Carpenter & Paterson Ltd
Zinc Electro Plating Crown Works
Sheradising Welshpool
Plastic Coating Powys
SY21 7BE

Tel: +44 (0)1938 552061

“Witchcraft”
Fax: +44 (0)1938 555306
The Carpenter and Paterson trade mark, “Witch”with Email: [email protected]
its witch on her broomstick, recalls the company’s
original deep roots in the New England States of North Or our Asia Office:
America.
Witches were still hunted in Massachusetts in 1692, Carpenter & Paterson Asia
and one witch-hunt in Salem village resulted in the 3, International Business Park
condemnation and execution of twenty innocent people 03-24, Nordic European Centre
who were burnt at the stake.- this execution site was in Singapore 609927
close proximity to where the original Carpenter and
Paterson factory was built in 1921 Tel: +65 6890 6516 / +65 9845 6158
Fax: +65 6890 6517
After this tragic episode, witchcraft was no longer Email: [email protected]
judged an indictable offence in Massachusetts.
Carpenter and Paterson Ltd, now an independent UK Visit our Website at: www.cp-ltd.co.uk
company, is proud of the “Witch” logo and the trade
mark remains well known within the industries it serves.

IV 04/10