Digital modules

3.32 Relay output module SM 322; DO 16 x Rel. AC 120/230 V; (6ES7322-1HH01-0AA0)

3.32 Relay output module SM 322; DO 16 x Rel. AC 120/230 V;

(6ES7322-1HH01-0AA0)

Order number
6ES7322-1HH01-0AA0

Properties
Properties of SM 322; DO 16 x Rel. AC 120/230 V:
● 16 outputs, electrically isolated in groups of 8
● Load voltage 24 VDC to 120 VDC; 24 VAC to 230 VAC
● Suitable for AC/DC solenoid valves, contactors, motor starters, FHP motors and signal
lamps.

Reaction to a shutdown of the power supply

Note
The internal 200-ms buffer capacitance discharges sufficient power after power off to allow
the user program to set a defined relay state.

Wiring and block diagrams of SM 322; DO 16 x Rel. AC 120/230 V



 







0 

 
  1

 /



  9
 
 






 0
 1

 0




① Channel number
② Status display - green
③ Backplane bus interface

S7-300 Automation System Module Data

Manual, 03/2011, A5E00105505-07 189
Digital modules
3.32 Relay output module SM 322; DO 16 x Rel. AC 120/230 V; (6ES7322-1HH01-0AA0)

Technical specifications of SM 322; DO 16 x Rel. AC 120/230 V

Technical specifications
Dimensions and weight
Dimensions W x H x D (mm) 40 x 125 x 117
Weight ca. 250 g
Module-specific data
Supports isochronous mode no
Number of outputs 16
Cable length
 unshielded max. 600 m
 shielded max. 1000 m

Voltages, currents, electrical potentials

Rated power supply L+ to the relays 24 VDC
Total current of outputs (per group) max. 8 A
Electrical isolation
 between channels and the backplane bus yes

 between channels yes

8
in groups of
Maximum potential difference
 Between Minternal and the power supply to relays 75 VDC/60 VAC

 Between Minternal and the power supply to relays and outputs 230 VAC

 Between outputs of different groups 500 VAC

Isolation test voltage

 between Minternal and the power supply to relays 500 VDC

 between Minternal and the power supply to relays and outputs 1500 VAC

 between outputs of different groups 2000 VAC

Current consumption
 from the backplane bus max. 100 mA
 from power supply L+ max. 250 mA

Power loss of the module typ. 4.5 W

Status, interrupts, diagnostics
Status display green LED per channel
Interrupts none
Diagnostic functions none

S7-300 Automation System Module Data

190 Manual, 03/2011, A5E00105505-07
 Digital modules
3.32 Relay output module SM 322; DO 16 x Rel. AC 120/230 V; (6ES7322-1HH01-0AA0)

Technical specifications
Actuator selection data
Thermal current, continuous max. 2 A
Minimum load voltage / current 10 V / 10 mA
Short-circuit current to IEC 947-5-1 200 A, with B10/B16 circuit breaker
Switching capacity and service life of contacts
 with resistive load
Voltage Current Number of switching cycles (typ.)
24 VDC 2.0 A 0.1 million
1.0 A 0.2 million
0.5 A 1.0 million
60 VDC 0.5 A 0.2 million
120 VDC 0.2 A 0.6 million
24 VAC 1.5 A 1.5 million
48 VAC 1.5 A 1.5 million
60 VAC 1.5 A 1.5 million
120 VAC 2.0 A 1.0 million
1.0 A 1.5 million
0.5 A 2.0 million
230 VAC 2.0 A 1.0 million
1.0 A 1.5 million
0.5 A 2.0 million
 with inductive load to IEC 947-5-1 DC13/AC15
Voltage Current Number of switching cycles (typ.)
24 VDC 2.0 A 0.05 million
1.0 A 0.1 million
0.5 A 0.5 million
DC 60 V 0.5 A 0.1 million
DC 120 V 0.2 A 0.3 million
24 VAC 1.5 A 1 million
AC 48 V 1.5 A 1 million
AC 60 V 1.5 A 1 million
AC 120 V 2.0 A 0.7 million
1.0 A 1.0 million
0.5 A 1.5 million
230 VAC 2.0 A 0.7 million
1.0 A 1.0 million
0.5 A 1.5 million
An external protective circuit will increase the service life of contacts.
Size of the motor starter max. size 5 to NEMA
Lamp load 50 W / 230 VAC
5 W / 24 VDC
Contact protection (internal) none

S7-300 Automation System Module Data

Manual, 03/2011, A5E00105505-07 191
Digital modules
3.32 Relay output module SM 322; DO 16 x Rel. AC 120/230 V; (6ES7322-1HH01-0AA0)

Technical specifications
Wiring two outputs in parallel
 for redundant load control supported (only outputs of the same group)

 for performance increase not supported

Control of a digital input supported

Switching frequency
 Mechanical max. 10 Hz

 with resistive load max. 1 Hz

 with inductive load to IEC 947-5-1, DC13/AC15 max. 0.5 Hz

 with lamp load max. 1 Hz

Wiring of the actuators using a 20-pin front connector

S7-300 Automation System Module Data

192 Manual, 03/2011, A5E00105505-07