Scribd
Upload
708 views

Heat Transfer Final Exam Problem & Solutions

1) The document describes four problems involving heat transfer through pipes, insulation, and heat exchangers. It involves calculating temperature distributions, heat transfer rates, positions in insulation, and the effects of fouling. 2) The first problem involves sketching the temperature distribution in a pipe insulation. The second asks to sketch the temperature in a spherical shell. The third requires calculating heat loss and sketching temperatures in a composite wall. 3) The fourth addresses finding the position of a temperature in pipe insulation, and the effects of moisture on heat gain. The fifth concerns calculating parameters of a counterflow heat exchanger before and after fouling.

Uploaded by

Ronard Pa–a
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
708 views

Heat Transfer Final Exam Problem & Solutions

1) The document describes four problems involving heat transfer through pipes, insulation, and heat exchangers. It involves calculating temperature distributions, heat transfer rates, positions in insulation, and the effects of fouling. 2) The first problem involves sketching the temperature distribution in a pipe insulation. The second asks to sketch the temperature in a spherical shell. The third requires calculating heat loss and sketching temperatures in a composite wall. 3) The fourth addresses finding the position of a temperature in pipe insulation, and the effects of moisture on heat gain. The fifth concerns calculating parameters of a counterflow heat exchanger before and after fouling.

Uploaded by

Ronard Pa–a
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

V.

1 Heat Transfer
5.1 A hot water pipe with outside radius r1 has a temperature T1. A thick
insulation, applied to reduce the heat loss, has an outer radius r2 and
temperature T2. On T-r coordinates, sketch the temperature distribution in
the insulation for one-dimensional, steady-state heat transfer with constant
properties. Give a brief explanation, justifying the shape of your curve. (25
points)
5.2 A spherical shell with inner radius r1 and outer radius r2 has surface
temperatures T1 and T2, respectively, where T1 > T2. Sketch the temperature
distribution on T - r coordinates assuming steady-state, one-dimensional
conduction with constant properties. Briefly justify the shape of your curve.
(25 points)

5.3 A composite wall separates combustion gases at 2600ºC from a liquid


coolant at 100°C, with gas- and liquid-side convection coefficients of 50 and
1000 W/m2·K. The wall is composed of a 10-mm-thick layer of beryllium
oxide on the gas side and a 20-mm-thick slab of stainless steel (AISI 304)
on the liquid side. The contact resistance between the oxide and the steel is
0.05 m2 K/W.
❑ What is the heat loss per unit surface area of the composite?
❑ Sketch the temperature distribution from the gas to the liquid.
(25 points)
5.4 A spherical tank of 3-m diameter contains a liquefied petroleum gas at
−60°C. Insulation with a thermal conductivity of 0.06 W/m·K and thickness
250 mm is applied to the tank to reduce the heat gain.
(a) Determine the radial position in the insulation layer at which the
temperature is 0ºC when the ambient air temperature is 20ºC and the
convection coefficient on the outer surface is 6 W/m2·K.
(b) If the insulation is pervious to moisture from the atmospheric air, what
conclusions can you reach about the formation of ice in the insulation?
▪ What effect will ice formation have on heat gain to the LP gas?
▪ How could this situation be avoided?
V.2 Heat Exchanger
5.5 A counterflow, concentric tube heat exchanger is designed to heat water
from 20 to 80°C using hot oil, which is supplied to the annulus at 160°C and
discharged at 140°C. The thin-walled inner tube has a diameter of Di = 20
mm, and the overall heat transfer coefficient is 500 W/m2·K. The design
condition calls for a total heat transfer rate of 3000 W.
(a) What is the length of the heat exchanger? (50 points)
(b) After 3 years of operation, performance is degraded by fouling on the
water side of the exchanger, and the water outlet temperature is only 65°C
for the same fluid flow rates and inlet temperatures. What are the
corresponding values of the heat transfer rate, the outlet temperature of the
oil, the overall heat transfer coefficient, and the waterside fouling factor,
R”ƒ,c? (50 points)

You might also like