Scribd
Upload
59 views

Beam Examples02

The document outlines the syllabus for a Structural Analysis - II course. It covers five units: (1) Moment Distribution Method for analyzing frames, (2) Slope Deflection Method for analyzing portal frames and two-hinged arches, (3) Approximate Methods for analyzing multi-storey frames, (4) Matrix Methods including the Stiffness Method, and (5) Influence Lines for indeterminate beams. It also provides sample objective questions and fill-in-the-blank questions related to analysis methods covered in the syllabus.

Uploaded by

pitamber
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
59 views

Beam Examples02

The document outlines the syllabus for a Structural Analysis - II course. It covers five units: (1) Moment Distribution Method for analyzing frames, (2) Slope Deflection Method for analyzing portal frames and two-hinged arches, (3) Approximate Methods for analyzing multi-storey frames, (4) Matrix Methods including the Stiffness Method, and (5) Influence Lines for indeterminate beams. It also provides sample objective questions and fill-in-the-blank questions related to analysis methods covered in the syllabus.

Uploaded by

pitamber
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 114

STRUCTURAL ANALYSIS - II

SYLLABUS
UNIT-I: MOMENT DISTRIBUTION METHOD
Analysis of Single Bay Single Storey Portal Frame including side Sway. Analysis
of inclined Frames. Kani’s Method: Analysis of Continuous Beams including
settlement of supports. Analysis of single bay single storey and single bay two
Storey Frames by Kani’s Method including side Sway. Shear Force Bending
Moment Diagrams. Elastic curves.

UNIT-II: SLOPE DEFLECTION METHOD


Analysis of Single Bay Single Storey Portal Frames by Slope Deflection Method
including side Sway – Shear Force Bending Moment Diagrams. Elastic curve. Two
Hinged Arches: Introduction-Classification of Two hinged Arches-Analysis of
Two Hinged Parabolic Arches due to temperature and elastic shortening of rib.

UNIT-III: APPROXIMATE METHODS OF ANALYSIS


Introduction – Analysis of multi-storey frames for lateral loads: Portal Method ,
Cantilever method and Factor method. Analysis of multi-storey frames for gravity
(vertical) loads. Substitute Frame method Analysis of Mill bents.

UNIT-IV: MATRIX METHOD OF ANALYSIS


Introduction –Static and Kinematic Indeterminacy-Analysis of Continuous beams
including settlement of supports, using Stiffness Method. Analysis of Pin –jointed
determinate plane frames using Stiffness method-Analysis of Single Bay Single
Storey Portal Frame including side Sway using Stiffness Method. Analysis of
Continuous Beams upto three degree of indeterminacy using Flexibility Method.
Shear Force Bending Moment Diagrams. Elastic curves.

UNIT-V: INFLUENCE LINES FOR INDETERMINATE BEAMS


Introduction –ILD for two span continuous beam with constant and variable
moments of inertia. ILD for Propped Cantilever beams. Indeterminate Trusses:
Determination of Static and Kinematic Indeterminacies - Analysis of trusses
having single and two degrees of internal and external indeterminacies-
Castigliano’s second Theorem.
UNIT-1:Objective Questions:
1.In moment distribution method ,the sum of distribution factors of all the members meeting at any
joint
a) zero
b) <1
c)1
d) >1
2. In the slope deflection equations, the deformations are caused by
a) shear force
b) Bending moment
c) axial force
d) none
3. Which of the following methods of structural analysis is a force method ?
a) slope deflection method
b) column analogy method
c) moment distribution method
d) none of the above
4. Which of the following methods of structural analysis is a displacement method ?
a) moment distribution method
b) column analogy method
c) three moment equation
d) none of the above
5. In the displacement method of structural analysis, the basic unknowns are
a) displacements
b) force
c) displacements and forces
d) none of the above

6. Which of the following is not the displacement method?


a) Equilibrium method
b) Column analogy method
c) Moment distribution method
d) Kani's method

7. Select the correct statement


a) Flexibility matrix is a square symmetrical matrix
b) Stiffness matrix is a square symmetrical matrix
c) both (a) and (b)
d) none of the above
8. When a load crosses a through type Pratt truss in the direction left to right, the nature of force in any
diagonal member in the left half of the span would
a) change from compression to tension
b) change from tension to compression
c) always be compression
d) always be tension

9.The ratio of a stiffness of a beam at a joints with one end hinged and other end fixed is

a) 1/2
b) 3/4
c) 1
d) 4/3

10Moment distribution method is developed by

a) Maney

b) Hardy cross

c) Muller

d) Gumbel

Fill in the blanks:

1. If the free end of acantilever of span l and flexural rigidity EI undergoes a unit displacement , the
bending moment induced at the fixed end --------------[IES-08]
2.The factor by which the applied moment is multiplied to obtain the end moment of any member is
known --------------------------------------------
3.In simply suppoted beam carrying point load at centre ,slope is maximum at -------------
4.In simply suppoted beam carrying point load at centre deflection is maximum at -------------
5. In cantilver deflection is maximum at ----------------------
6. Moment distribution method is developed by -------------------------
7.The relative stiifness of member with far end fixed is---------------------
8.The relative stiifness of member with far end hinged is---------------------
9.. A single bay single storey portal fgrames has a hinged left support and a fixed right support .it is
loaded with udl on th e beam .The deformation of the frame is------------------[GATE-95]
10.the factor by which the moment at simply supported end is multiplied to get moment carried over to
the other end is-----------------

Key :

1.c 2.b, 3.b,4.a,5.a ,6.b,7.c,8.a 9.b, 10.b


Fill in the blanks: 1.6EI/L2 , 2. Distribution factor 3.ends 4. Centre 5. Free end 6.Hardy cross
7.I/L 8.3I/4L 9- it would sway to the left side, 10.Carry over factor.
UNIT-2:Objective Questions:
Objective Questions:
1. In the slope deflection equations, the deformations are considered to be caused by

i) bending moment ii) shear force iii) axial force


The correct answer is
a) only (i)
b) (i)and(ii)
c) (ii) and (iii)
d) (i), (ii) and (iii)

2. For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the
horizontal thrust
a) is increased
b) is decreased
c) remains unchanged
d) becomes zero

3..Slope-deflection is developed by

a) Maney

b) Hardy cross

c) Muller

d) Gumbel

4.The slope deflection equations give the relationship between

a)slope and deflection only

b)BM and rotation only

c)BM and vertical deflection only

d)BM ,rotation and deflections

5.In slope deflection method the displacements considered are due to

a)SF

b)BM

c)Axial force and BM

D)SF and BM
6.The number of simultaneous equations to be solved in the slope deflection method is equal to

a)static indeterminacy

b)kinematic indeterminacy

c)no of joint displacements in the structure

d)none of the above

7.The slope deflection method formulates

a)equilibrium conditions only

b)compatibility conditions only

c)both equilibrium and compatibility conditions

d)either equilibrium or compatibility conditions

8.The slope deflection method in structural analysis falls in the category of

a)force method

b)flexibility method

c)consistent deformation method

d)stiffness method

9.In slope deflection method the no of unknown rotations at various joints are determined

by considering

a)the equilibrium of joints

b)the rigidity of joint

c)the equilibrium of structure

d)none of the above

10.In slope deflection method , the end moments for any member are expressed

a)as zero

b)in terms of unknown end rotations

c)as equal
d)none of the above

Fill in the blanks:

11.Slope-deflection method primarily gives ------------------------------

12. The horizontal thrust for two hinged parabolic arch is------------

13. Degree of static indeterminacy of a two hinged arch is ---------------

14. Degree of static indeterminacy of a three hinged arch is ---------------

15. The strain energy due to volumetric strain---------------------- to volume

16. The strain energy due to volumetric strain---------------------- to bulk modulus

17. The effect of normal thrust in the arch is to shorten the ---------- of the arch.

18. The radial shear of two hinged parabolic arch is-----

19. The normal thrust of any arch is ------

20. The net horizontal thrust due to temperature effect is------

KEY 1- a, 2-b,3-d, 4-b,5-b,6-c, 7-a,8-d,9-c,10-b

11-displacements, 12-H=∫My ds / ∫y2 ds, 13-1 , 14-zero, 15-4, 16-2

17-rib, 18-R.S=Hasin ѳ-Vacos ѳ, 19 –N.T-=Hasin ѳ-Vacos ѳ, 20-H.T=[Dh/H=-dh/h]

You might also like