SR609C Operation manual

Content
1. Safety information ............................................................................................3
1.1 Installation and commissioning .......................................................................3
1.2 Liability waiver ...................................................................................................3
1.3 Signal description ..............................................................................................4
2. Installation .............................................................................................................4
2.1 Mounting controller ...........................................................................................4
2.2 Power connection..............................................................................................5
2.3 Terminal connection ..........................................................................................6
3. System diagram ...................................................................................................8
4. Functions operation.............................................................................................9
4.1 Signals on display and function code ............................................................9
4.2 Button Description ...........................................................................................10
4.3 Menu structure ................................................................................................. 11
4.4 Menu description .............................................................................................12
4.5 Setting time ......................................................................................................13
4.6 THEH Timing heating .....................................................................................13
4.7 TCYC Setting the running time/ temperature of DHW pump...................15
4.8 AHO Automatically thermostat function .......................................................19
4.9 OTF Three time sections set (Timer function) ............................................21
4.10 PHTC Time controlled pipe heating protection ........................................22
4.11 TDIS Thermal disinfection ...........................................................................24
4.12 CFR Tank anti-freezing protection .............................................................25
4.13 UNIT Celsius degree and Fahrenheit unit switch ....................................27
4.14 BEEP Beeper error warning ........................................................................27
4.15 RST Reset function.......................................................................................27
4.16 M.H manual heating .....................................................................................28
4.17 Intelligent heating mode...............................................................................28
-1-
SR609C Operation manual

4.18 Economic mode.............................................................................................29

4.19 View the measuring value ...........................................................................29
5. Protection function.............................................................................................30
5.1. Memory protection .........................................................................................30
5.2 Screen protection ............................................................................................30
5.3 Trouble protection ...........................................................................................30
6. Quality Guarantee .............................................................................................30
7. Technical specification ......................................................................................31
8. Delivery list .........................................................................................................31

-2-
SR609C Operation manual
1. Safety information
We have carefully checked the text and pictures of this manual and provided the
best of our knowledge and ideas, however inevitable errors maybe exist. Please
note that we cannot guarantee that this manual is given in the integrity of image
and text, incorrect, incomplete and erroneous information and the resulting
damage we do not take responsibility.

1.1 Installation and commissioning

 When laying wires, please ensure that no damage occurs to any of the
constructional fire safety measures presented in the building.
 The controller must not be installed in rooms where easily inflammable gas
mixtures are present or may occur.
 The permissible environmental conditions can’t be exceeded at the site of
installation.
 Before connecting the device, make sure that the energy supply matches
the specifications that controller requires.
 All devices connected to the controller must conform to the technical
specifications of the controller.
 All operations on an open controller are only to be conducted cleared from
the power supply. All safety regulations for working on the power supply
are valid.
 Connecting and /or all operations that require opening the collector (e.g.
changing the fuse) are only conducted by specialists.

1.2 Liability waiver

The manufacturer can’t monitor the compliance with these instructions or the
circumstances and methods used for installation, operation, utilization and
maintenance of this controller. Improper installation can cause damages to
material and person. This is the reason why we do not take over responsibility
and liability for losses, damages or cost that might arise due to improper

-3-
SR609C Operation manual

installation, operation or wrong utilization and maintenance or that occurs in

some connection with the aforementioned. Moreover we do not take over
liability for patent infringements or infringements – occurring in connection with
the use of this controller on the third parties rights. The manufacturer preserves
the right to put changes to product, technical data or installation and operation
instructions without prior notice. As soon as it becomes evident that safe
operation is no longer possible (e.g. visible damage). Please immediate take
the device out of operation. Note: ensure that the device can’t be accidentally
placed into operation.

1.3 Signal description

Safety indication: Safety instructions in the text are marked with a
warning triangle. They indicate measures which can lead to injury of
person or safety risks.
Operation steps: small triangle “►”is used to indicate operation step.
Notes: Contains important information about operation or functions.

2. Installation

2.1 Mounting controller

Size of controller for electrical heater of 1500W

-4-
SR609C Operation manual

Size of controller for electrical heater of 3000W

Note: the controller can only be installed in an area having an adequate level of
protection.
►Choosing a suitable site
►Drilling the up fixing hole ①
►Screwing on the screw
►Taking away the cover plate
►Hanging the bottom plate on the fixing hole ①
►Marking the position of fixing hole ②
►Taking away the bottom plate
►Drilling the hole ②
►Re-hanging the bottom plate on screw ①
►Fixing bottom plate with screw ②

2.2 Power connection

Depending on the type of installation, the cables may enter the device through
the rear hole of the case ③or the lower side hole of the case ④

-5-
SR609C Operation manual
Notes: the flexible wire must be fastened to the case using the strain-relief
clamps provided.

③ ③ ④ ④

2.3 Terminal connection

Before to open the terminal, please be sure to switch-off the power
and pay attention to the local electricity supply rules.

 Terminal layout of controller for electrical heater of 1500W

 FU1: the fuse of controller, AC250V/0.5A

 Power terminal N, L: 10A, for power connection, L: live wire, N: zero wire,
protective wire, please ensures to connect to ground.
 Output ports
H1: Designed for electrical heater, electromagnetic relay, max. power is
1500W,
R1: Designed for anti-freezing heating cables, Electromagnetic relay, max.
power is 500W
Note:If power supply 100~130V/ AC 50/60Hz,Maximum power of
H1:750W ;Maximum power output of R1:250W
-6-
SR609C Operation manual
 Input ports
Input port T1：for NTC10K, B=3950, ≤135oC sensor (PVC cable ≤105oC)
designed for measuring the temperature of tank.
Input port T2: for NTC10K, B=3950, ≤135oC sensor (PVC cable
o
≤105 C),Optional.
 Terminal layout of controller for electrical heater of 3000W

 Power terminal N, L: 20A, for power connection, L: live wire, N: zero wire,
protective wire, please is sure to connect to ground.
 Output ports
H1: Designed for electrical heater, electromagnetic relay, max. power is
3000W,
R1: Designed for anti-freezing heating cables, Electromagnetic relay, max.
power is 500W

Note:If power supply 100~130V/ AC 50/60Hz,Maximum power

output of H1:1500W ;Maximum power output of R1:250W
 Input ports
Input port T1：for NTC10K, B=3950, ≤135oC sensor (PVC cable ≤105oC)
designed for measuring the temperature of tank.
o
Input port T2: for NTC10K, B=3950, ≤135 C sensor (PVC cable
≤105oC),Optional.
-7-
SR609C Operation manual

Note: sensor T2 is not listed in the standard delivery package,

self-purchase if need.
 Advice regarding the installation of temperature sensors:
► Only original factory equipped NTC10K,B=3950 temperature sensors are
approved for using with tank, it is equipped with 20m PVC cable, and the cable
is temperature resistant up to 105 oC, connect the temperature sensors to the
corresponding terminals with either polarity.
► All sensor cables carry low voltage, and to avoid inductive effects, must not
be laid close to 230 volt or 400 volt cables (minimum separation of 100mm).
► Sensor cables may be extended to a maximum length of ca. 100 meter,
when cable’s length is up to 50m, and then 0.75mm2 cable should be used.
When cable’s length is up to 100m, and then 1.5mm2 cables should be used.

3. System diagram

Note: this diagram is only for reference.

-8-
SR609C Operation manual
4. Functions operation
Before switching-on the power, please connect sensor to the input port of
controller, connect electrical heater to the output port of controller.
After power is switch on, the controller runs an initialization phase for 5 seconds,
then controller runs a commissioning menu, it leads the user through the most
important adjustment channels needed for operating the system.

4.1 Signals on display and function code

LCD display
Code Description Code/Signal Lighting Code/Signal Blink

Intelligent heating function Function is triggered Function is working

Thermal disinfection Countdown of disinfection

Function is triggered
function function working （DDIS）

Timer function Function is triggered Function is working

Pipe heating function Function is triggered Function is working

Timing heating function Function is triggered Function is working

Temperature controlled
Function is triggered Function is working
DHW within 3 time sections
Time controlled DHW within
Function is triggered Function is working
3 time sections
Automatic thermostat Function is triggered Function is working

Economic mode

Anti freezing protection Function is triggered Function is working

Manual heating function

Warning of sensor error

-9-
SR609C Operation manual
4.2 Button Description

Layout of button
 Button description
“CLOCK” button: current time setting
“M.H” button: manual heating switch on/off
“SET” button: confirm the setting or activate the setting program
“ESC” button: exit or return to the previous menu
“ ” button: increase adjustable value or upwards menu
“ " button: decrease adjustable value or downwards menu

 Main menu operation steps

► Press “SET” button for 3 seconds to access main menu
► Press “ ” to adjust the menu
► Press “SET” to access submenu

 Submenu operation steps

► Press “SET” to access submenu
► Press “SET” again to the adjustable item, press “ ” to select “ON” to
open the option, or select “OFF” to close this option
► Press “SET” or “ESC” to confirm the adjust
► Press “ ”to access the next submenu
► Press “SET” to the adjustable value
► Press “ ” to adjust value

- 10 -
SR609C Operation manual

► Press “SET” or “ESC” to confirm the adjust

Note：after accessing the adjust channel, if no any button is pressed for 3

minutes, then display returns to the main interface.

4.3 Menu structure

Main menu

Submenu

 It is possible to given a detailed set through the submenu, please

completely learn the submenu.
- 11 -
SR609C Operation manual
4.4 Menu description
Code Code Default
Description
(Main menu) (Submenu) value
THET Timing heating
OFF Set the temperature and time of
TCYC
circulation pump of DHW
ON Switch-on condition of DHW
STAT
circulation pump
40℃/03MI Switch-on temperature and time of
CYCO
N DHW circulation pump
45℃/15MI Switch-off temperature and time of
CYCF
N DHW
AH OFF Automatic thermostat
S2 Selection of sensor for thermostat
AHS
function
OTF OFF Timer
PHTC OFF Pipe heating protection
PHST 00:00 Start time of pipe heating
PHFT 23:59 Stop time of pipe heating
PHRT 10MIN Set the running time of pipe heating
PHET 30MIN Set the interval time of pipe heating
TDIS OFF Thermal disinfection
PDIS 07 Monitoring days
DDIS 10MIN Disinfection running time
TDIS 70℃ Disinfection running temperature
SDIS 18:00 Start time of disinfection
CFR OFF Tank anti-freezing protection
03℃ Switch-on temperature of
CFRO
anti-freezing protection
05℃ Switch-off temperature of
CFRF
anti-freezing protection
UNIT ℃ Temperature unit selection
BEEP OFF Warning of sensor error
RST Reset to factory value

Note: R1 output port is designed for one of functions from TCYC, AH, OTF,
PHTC, if one of these functions is selected to be activated, and then the others
should be deactivated in the menu.

- 12 -
SR609C Operation manual
4.5 Setting time
►Press “Clock” button, time displays on the
screen, hour “00” blinks on the screen.
►Press “▲▼” button to set hour of clock
►Repress “Clock”, minute “00”blinks
► Press “▲▼” button to set minute of clock.
► Press “Clock” to exit program, or waiting for 20 seconds, controller exits
automatically, the set parameter is saved automatically.

Note: at the case that power is switched-off, time can be kept for
36hours.

4.6 THEH Timing heating

Description:
Electrical heater can be integrated into solar system used as back-up
heating of system, and it can be triggered automatically at preset time by
preset temperature. Within a preset time section, when the temperature
(T1) of tank drops below the preset switching-on temperature of this function,
electrical heating (H1) starts to work, when T1 rises up to the preset turning
off temperature, electrical heating (H1) is stopped.

Within 24 hours, three time sections can be set with this controller.
Factory set:
The first time section: electrical heating function starts at 4:00 and ends at
5:00 am. Within this time section, switch-on temperature is 40℃,
switch-off temperature is 50℃.
The second time section: from 10:00 to 10:00 am, it means there is no
electrical heating in this time.
The third time section: electrical heating function starts at 17:00 and ends at
22:00 pm. Within this time section, the switch-on temperature is 50℃,
- 13 -
SR609C Operation manual

switch-off temperature is 55℃.

The switch-on temperature adjustable range: 0℃ ~ (OFF-2 ℃)

The switch-off temperature adjustable range: (ON+2 ℃) ~ 95℃

If you want to shut off one timing heating, then you can set the turning on
time and turning off time same value (for example, the second time section
no this function, then you can set turning on/off time is 10:00 ~ 10:00)

When time is outside of the preset time section, electrical heating doesn’t
work automatically even when the tank temperature reaches the switch –on
temperature of heating.

Setup steps:
►Press “SET” button for 6 seconds, to access the
main menu and select menu “THET”.
►Press “SET” button again to access the program.
►Press “SET” button again, the first switch-on time
and temperature parameters “th1O 04：00 ”displays
and blinks on the screen.
►Press “SET” button, hour “04” blinks on the screen.
►Press “▲▼” button, to set hour of the switch-on
time of heating
►Press “SET” button, minute “00” blinks on the screen.
►Press “▲▼” button, to set minute of the switch-on time of heating
►Press “SET” button, temperature “40” blinks on the screen.
►Press “▲▼” button, to set the switch-on temperature of heating.
►Press “SET” or “ESC” button to confirm.

- 14 -
SR609C Operation manual

►Press “▲” button, to access the first switch-off time

and temperature parameters, “th1F 05：00 ”displays
and blinks on the screen.
►Press “SET” button, hour “05” blinks on the screen.
►Press “▲▼” button, to set hour of the switch-off
time of heating
►Press “SET” button, minute “00” blinks on the screen.
►Press “▲▼” button, to set minute of the switch-off time of heating
►Press “SET” button, temperature “45” blinks on the screen.
►Press “▲▼” button, to set the switch-on temperature of heating.
►Press “SET” or “ESC” button to confirm.
►Press “▲” button, to access the second switch-on time and temperature
parameters, “th2O 04：00 ”displays and blinks on the screen. Doing like above
to set time and temperature for the second section and the third section.

When heating signal displays on the screen, it indicates timing heating is

activated.

4.7 TCYC Setting the running time/ temperature of DHW pump

Description:
This controller provides an output for running DHW circulation pump, which can
be controlled by a temperature, at this case, an extra circuit pump (connect to
the output R1) and an extra temperature sensor mounted on the hot water
return pipe (connect to the input T2) should be installed in the system. When the
temperature of DHW return is lower than the preset switch-on temperature,
circuit pump is triggered, until temperature rises up to the switch-off temperature,
pump is stopped.

- 15 -
SR609C Operation manual
 DHW pump running at below 2 modes:
 Running controlled by time within the three time sections
If sensor T2 is not connected to the controller, then time controlled mode is
selected automatically, within a running time section, as default set, pump runs
for 3 minutes and then ceases for 15 minutes, same process repeated within
the running time section. Running time can be adjusted from 1-30Min; Stop time
can be adjusted from 0-60Min.
If the stop time ( CYCF) is set to 0 minute， then
within the time section, DHW pump keeps running
without any intervals.
Default time sections:
The first time section starts at 05.00 am, closes at
7:00am.
The second time section starts at 11.00 am, and closes at 13:00pm.
The third time section starts at 17.00 pm, and closes at 22:00pm.

 Running controlled by temperature within the three time sections

When sensor T2 is connected to the controller, then temperature controlled
mode is selected automatically, within a running time section, as default set,
pump R1 runs when T2 is below 40oC, and pump R1 stops when T2 reaches to
45oC

Startup condition for temperature controlled mode (STAT): when tank

temperature T1 is 2oC higher than the preset switch-off temperature, and then
DHW circuit pump is triggered.

Note:
STAT not available on the time controlled mode.

Default time sections:

- 16 -
SR609C Operation manual

The first time section starts at 05.00 a.m., closes at 7:00a.m.

The second time section starts at 11.00 a.m., closes at 13:00p.m..
The third time section starts at 17.00 p.m. closes at 22:00p.m.
If it is needed to close one time section, just set the start time and stop time at a
same value (e.g. 10:00 starts, 10:00 closes)

Note:
DHW pump temperature controlled mode is prior to time controlled mode.
When sensor T2 is connected to the controller, then time controlled mode is
switched -off automatically, and switched to temperature controlled mode.
If sensor T2 should be installed, in order to avoid measuring error, please
ensure a safety distance of 1.5m to tank.
The setting steps for time controlled mode and temperature controlled mode is
same.

Setup steps (example with temperature controlled

mode)
►Press “SET” button for 6 seconds, to access the
main menu and select menu “TCYC”.
►Press “SET” button again, “OFF” blinks on the
screen.
►Press “▲▼” button, to activate this function
►Press “SET” or “ESC” button to confirm.

►Press “▲” button, “STAT” displays (startup temperature of DHW pump)

►Press “SET” button again, “STAT” blinks on the screen.
►Press “▲▼” button, to activate this function
►Press “▲” button, “CYCO 40oC” displays (switch
–on temperature of DHW pump)

- 17 -
SR609C Operation manual

►Press “SET” button again, “40 oC” blinks on the screen.

►Press “▲▼” button, to adjust switch-on temperature, adjustable range 0 oC～
(OFF-2 oC)
►Press “SET” or “ESC” button to confirm.
o
►Press “▲” button, “CYCF 45 C” displays (switch
–off temperature of DHW pump)
►Press “SET” button again, “45 oC” blinks on the
screen.
►Press “▲▼” button, to adjust switch-off temperature, adjustable range (ON+2
o
C) ～55 oC.
►Press “SET” or “ESC” button to confirm.

►Press “▲” button, to the first time section setting,

“tC 1O 05:00”displays (switch –on time of the first
time section of DHW pump)
►Press “SET” button again, hour “05” blinks on the screen.
►Press “▲▼” button, to adjust hour of the switch-on time
►Press “SET” button again, minute“00” blinks on the screen.
►Press “▲▼” button, to adjust minute of the switch-on time
►Press “SET” or “ESC” button to confirm.

►Press “▲” button, to the first time section setting, “tC 1F 07:00”displays
(switch –off time of the first time section of DHW
pump)
►Press “SET” button again, hour “07” blinks on the
screen.
►Press “▲▼” button, to adjust hour of the switch-off time
►Press “SET” button again, minute“00” blinks on the screen.
►Press “▲▼” button, to adjust minute of the switch-off time
- 18 -
SR609C Operation manual

►Press “SET” or “ESC” button to confirm.

►Press “▲” button, to the second time section setting, “tC 2O 11:00”displays
(switch –on time of the second time section of DHW pump), repeat above steps
to set the second time section and the third time section.

If it is needed to close one time section, just set the start time and stop time at a
same value (e.g. 10:00 starts, 10:00 stops)

When DHW pump signal displays and blinks, it

indicates that temperature controlled DHW pump
mode is activated,
When signal displays and blinks, it indicates the time controlled DHW
pump mode is activated,

4.8 AHO Automatically thermostat function

Automatically thermostat function is independent from solar system, it is used to
release the extra heat to reduce the tank temperature or to trigger back-up
heater to heat tank to the desired temperature. This function needs an
electromagnetic valve or circulation pump R1, corresponding temperature is T2
or T1.
Note:
AHO<AHF: this thermostat function is used to control the back-up heater
AHO>AHF: this thermostat function is used to release the extra heat from tank
Setup steps:
► Select main menu AH
► Press “SET” button, parameter “OFF” blinks on
the screen
► Press “ ” to activate this function
►Press “SET” or “ESC” button to confirm the set.

- 19 -
SR609C Operation manual

►Press “ ” button, parameter “AHS S2”

appears (sensor selected for this function, S1
presents T1, S2 presents T2)
► Press “SET” button, parameter “S2” blinks on
the screen
► Press “ ” to select sensor
►Press “SET” or “ESC” button to confirm.
►Press “ ” button to access the setting
program of timer of the thermostat function, “t1 O
00：00 ”displays, it is ready for set the start time of
the first time section.
► Press “SET” button, hour “00” blinks on the screen
► Press “ ” to set hour of the start time
► Press “SET” button, minute “00” blinks on the screen
► Press “ ” to set minute of the start time
► Press “SET” button, temperature “40 oC” blinks
on the screen, adjustable range is 0 oC ~ 95oC
► Press “ ” to set the switch-on temperature of the thermostat function.
►Press “SET” or “ESC” button to confirm.

►Press “ ” button to access the setting

program , “t1F 23：59 ”displays, it is ready for set
the close time of the first time section.
► Press “SET” button, hour “23” blinks on the
screen
► Press “ ” to set hour of the close time
► Press “SET” button, minute “59” blinks on the screen
► Press “ ” to set minute of the close time
- 20 -
SR609C Operation manual

► Press “SET” button, temperature “45 oC” blinks on the screen，adjustable

range is 0oC ~ 95oC
► Press “ ” to set the switch-off temperature of the thermostat function.
►Press “SET” or “ESC” button to confirm.

►Press “ ” button to access the setting program of second time section,

repeat above steps to set second time section and the third time section.

When the signal of thermostat “AH” is blinks on the screen, it indicates that the
thermostat function is activated.

4.9 OTF Three time sections set (Timer function)

Description:
Controller has timer function, within the set time section, output R1 is
switched-on; outside the time section, and then output R1 is switched-off.

Setup steps:
►Select OTF DHW circulation main menu.
►Press “SET” button, “OFF” displays on the screen.
►Press“ ”button to activate the function
►Press “SET” or “ESC” to confirm
►Press“ ”button to access the setting program to
set the timer, “t1O 00:00”displays on the screen, it is
ready for setting the start time of the first time
section.
►Press “SET” button, hour“00”blinks
►Press“ ”button to adjust hour of the start time
►Press “SET” button, minute“00”blinks,
►Press“ ”button to adjust minute of the start
time
- 21 -
SR609C Operation manual

►Press “SET” or “ESC” to confirm

►Press“ ”button to set the close time of the first time section, “t1F 00：
00”displays on the screen.
►Press “SET” button, hour“00”blinks
►Press“ ”button to adjust hour of the close time
►Press “SET” button, minute“00”blinks,
►Press“ ”button to adjust minute of the close time
►Press “SET” or “ESC” to confirm
►Press“ ”button to access the program of setting the second time section,
repeat above steps to set the second time section and third time section.
If it is needed to close one time section, just set the start time and stop time at a
same value (e.g. 10:00 starts, 10:00 closes)
When timer signal blinks, it indicates that the timer function is activated.

4.10 PHTC Time controlled pipe heating protection

Description:
In winter, when outdoor temperature is low, controller will trigger the pipe
heating protection function to avoid pipe leakage due to freezing.
Example: at the preset time section, if running time of pipe heating is set with 10
minutes, the interval of pipe heating is set with 10 minutes, then the heating
function runs for 10 minutes, then it stops for 10 minutes, this heating process is
repeated within the time section, through this setting, it can avoid to give power
to heating wires for long time, save electricity and can avoid fire due to aging of
wire.

Setup steps:
►Select menu PHTC pipe heating function.
►Press “SET” button， “OFF” blinks on the screen
►Press“ ”button to activate this function

- 22 -
SR609C Operation manual

►Press “SET” or “ESC” to confirm

►Press“ ” to access the setting program, “PHST
00:00”Displays on the screen, it is ready to set the
start time of the first time section.
►Press “SET” button, hour“00”blinks
►Press“ ”button, adjust the hour of the start
time
►Press “SET” button, minute“00”blinks
►Press“ ”button to adjust the minute of the start time
►Press “SET” or “ESC” to confirm
►Press“ ”button, “PHFT 23:59”displays on the screen, it is ready to set the
close time of the first time section.
►Press “SET” button, hour “23” blinks
►Press“ ”button, adjust the hour of the close
time
►Press “SET” button, minute“59”blinks
►Press“ ”button to adjust the minute of the close time
►Press “SET” or “ESC” to confirm

►Press“ ”button to set the running time of pipe

heating function, “PHRT 10MIN”displays on the
screen.
►Press “SET” button, “10MIN” blinks
►Press“ ”button, to adjust the running time of pipe heating, (minute)
adjustable range is 1~ 60MIN.
►Press “SET” or “ESC” to confirm
►Press“ ”button to set the interval time, “PHET 30MIN”displays on the
screen
►Press “SET” button, “30MIN”blinks

- 23 -
SR609C Operation manual

►Press “ ” button to adjust the interval (minute), adjustable range is

0~90MIN.
►Press “SET” or “ESC” to confirm

When the timer signal blinks on the screen, it indicates that the timer
function is activated.。

Note: if the interval time PHET is set with 0 minute, then within the time
section, pipe heating will run without stop.

4.11 TDIS Thermal disinfection

Description:
In order to avoid occurring bacteria in water tank, controller will trigger the
back-up heater to heating tank to the required temperature to kill the bacteria.
Therefore, tank temperature is monitoring by controller at the monitoring period
(PDIS), if the temperature is not reached to the desired temperature during this
monitoring period, then controller will trigger the electrical heater at the preset
start time (SDIS), and controller ensures to heat tank temperature during the
heating period (DDIS) is always higher than the desired disinfection
temperature (TDIS). When thermal disinfection function is working, countdown
time starts, and signal blinks on the screen, countdown time finished,
thermal disinfection heating is stopped. This function stops.

Setup steps:
►Select TDIS thermal disinfection main menu
►Press “SET” button, “OFF” blinks
►Press“ ”button, to activate this function
►Press “SET” or “ESC” to confirm
►Press“ ”button, to set the days of a thermal
disinfection period, “PDIS 07”displays on the screen.
- 24 -
SR609C Operation manual

►Press “SET” button, “07”blinks

►Press“ ”button, to set the days of a thermal
disinfection period, adjustable range is 1-30 days.
►Press “SET” or “ESC” to confirm
►Press“ ”button，to set the disinfection heating
time “DDIS 10” displays.
►Press “SET” button, “10”blinks on the screen.
►Press“ ”button, to set the heating time,
adjustable time is 1-120 minutes
►Press “SET” or “ESC” to confirm
►Press“ ”button to set the heating temperature,
“TDIS 70”displays on the screen.
►Press “SET” button, “70℃”blinks
►Press “ ”button，set the heating temperature, the adjustable range is
0-90℃
►Press “SET” or “ESC” to confirm
►Press“ ”button to set the start time of thermal disinfection function, “SDIS
18：00”displays on the screen.
►Press “SET” button, “18”blinks
►Press“ ”button to set the start time of thermal disinfection function
►Press “SET” or “ESC” to confirm
When thermal disinfection signal blinks on the screen, it indicates that the
disinfection function is activated.

4.12 CFR Tank anti-freezing protection

Description：
In winter, when outdoor temperature is very low, in order to avoid freezing of
collector tube/ tank, when controller measures the tank temperature T1 drops to
only 3oC (factory set), controller will trigger the electrical heater to heat tank until

- 25 -
SR609C Operation manual

its temperature rises up to 5oC, and then tank anti-freezing function is

deactivated automatically.

Setup steps:
►Select main menu CFR tank anti-freezing
protection function
►Press “SET” button, “OFF” blinks
►Press “ ”button to activate the function

►Press “SET” or “ESC” to confirm

►Press“ ”button, “CFRO 03”displays (switch-on
temperature of tank anti-freezing protection)
►Press “SET” button, “03”blinks
►Press“ ”button to adjust the switch on

temperature for this function, adjustable range is

0-8℃）
►Press “SET” or “ESC” to confirm
►Press“ ”button, “CFRF 05”displays (Switch-off temperature of tank
anti-freezing protection)
►Press “SET” button, “05”blinks
►Press“ ”button, to adjust the switch-off temperature, adjustable range is
o
2-10 C.
►Press “SET” or “ESC” to confirm
When anti-freezing signal blinks, it indicates anti-freezing function is
activated.

- 26 -
SR609C Operation manual
4.13 UNIT Celsius degree and Fahrenheit unit switch
Setup steps:
►Select this function menu UNIT,

►Press “SET” button, “TEMP ℃” displays on the

screen
► Press “SET” button again, “oC” blinks
►Press “ ”to switch the temperature unit
►Press “SET” or “ESC” to confirm

4.14 BEEP Beeper error warning

When temperature sensor has error, this function will send warning to manager.
When beeper sounds, press “ESC” to exit the warning function.
Setup step:
►Select BEEP warning function menu
►Press “SET” button, “BEEP OFF” displays
►Press “SET” button，“OFF” blinks
►Press“ ”button to activate the function
►Press “SET” or “ESC” to confirm

4.15 RST Reset function

Through this function, it is possible to recover all parameters to the factory set.
Setup steps：
►Select RST main menu
►Press “SET” button, “YES” blinks
►Press “SET” button for 3 seconds, then beeper
sounds “di….” 3 times, and then “YES” lighting, it
indicates the controller program is recovered to the
factory set.
►Press “SET” or “ESC” to confirm

- 27 -
SR609C Operation manual
4.16 M.H manual heating
Description:
You can trigger back-up electrical heater by this controller to adjust the tank
temperature. When controller measures the temperature T1 is below the
desired temperature, it will trigger the electrical heater until the tank temperature
(T1) rises up to the desired temperature.

Activate/deactivate the function

►Press “M.H” button for 3 seconds, temperature“60 oC” blinks on the screen.
►Press“ ”button to adjust the desired
temperature, adjustable range 10oC～80 oC, factory
set is 60 oC
►Press “M.H” or press “ESC” button or waiting for 20 seconds to start the
manual heating function, and displays manual heating signal
►Press “M.H” again, to switch-off manual heating function.

Note: manual heating can heat tank only for one time, when manual
heating function is activated, tank is heated until its temperature reaches to the
desired value, and then manual heating is deactivated automatically.

4.17 Intelligent heating mode

At the case that solar energy is not enough, in order to ensure a enough hot
water for customer, controller will automatically measure the tank temperature
at the preset time, if the default temperature is not reached, controller trigger the
electrical heater to heat tank until the temperature rises up to the default value.
Factory set(Not change ):
first heating time is 13:00 and desired temperature is 30 oC
second heating time is 14:00 and desired temperature is 35 oC,
third heating time is 15:00, desired temperature is 40oC,
forth heating time is 16:00, desired temperature is 45 oC,
- 28 -
SR609C Operation manual

fifth heating time is 17:00, desired temperature is 50 oC,

Setup steps:
►Press “ ”button for 3 seconds, displays on
the screen, Intelligent heating mode is activate.
►Press“ ”button for 3 seconds again, signal
closed, Intelligent heating mode deactivated.

When intelligent heating signal blinks on the screen, it indicates this function
is working.

4.18 Economic mode

Description:
At the case of economic mode, timing heating function is deactivated
automatically; heating can only be triggered by manual heating function.

Activate/deactivate this function:

►Press“ ”button for 3 seconds, signal blinks,
eco mode activated.
►Press“ ”button for 3 seconds again, signal
closed, eco mode deactivated.

Note: if the timing heating function is needed to be used, then the eco
mode should be deactivated.

4.19 View the measuring value

When controller works normal, by pressing “ ” button, it is possible to view
the T1, T2 temperature value, running time and software version.
Note:
1. T2 value can be viewed only when the corresponding function is activated.

- 29 -
SR609C Operation manual

2. At the view status, if no any button is pressed within 20 seconds, display

turns to the main interface.

5. Protection function

5.1. Memory protection

In case power failure occurs, controller keeps the parameter settings
unchanged.

5.2 Screen protection

When no any press on button for 5 minutes, screen protection is activated
automatically, and then LCD lighting lamp is switched-off. Through press any
button to light LCD lamp again.

5.3 Trouble protection

When temperature sensor’s (T1) wiring is interrupted, not connected or short
circuit, controller switches off the corresponding signal output, and
simultaneously “ - - -” error code displays on the screen.

6. Quality Guarantee
The warrantee expires within 12 months after the date of purchasing the
controller.

- 30 -
SR609C Operation manual
7. Technical specification
 Power supply：AC230V ±10%,50Hz
 Power consumption：< 3W
 Accuracy of temperature measuring： ± 2oC
 Range of tank temperature measuring： 0 ~100 oC
 Suitable power of electrical heater: ≤ 1.5KW or ≤ 3KW (optional)
 Inputs:T1: NTC10K, B3950 sensor (≤ 135oC) for tank, (PVC cable ≤105oC),
T2: temperature sensor, optional
 Outputs：H1 for electrical heater, R1: Relay.
 Ambient temperature ：-10oC ~ 50oC.
 Water proof grade：IP40.

Note:
If power supply:AC110V±10%,60Hz:
Suitable power of electrical heater: ≤ 0.75KW or ≤ 1.5KW (optional)
Suitable power of R1: ≤ 0.25KW

8. Delivery list
 Controller 1 piece
 Power cable 10A ( for controller of 3000W, plug not provided) 1 piece
 Customer manual 1 piece
 NTC10K sensor（size: φ6*50mm,cable length20 m） 1 piece
 Accessories 1 bag

- 31 -