DRAFT: TENTATIVE COST ESTIMATE OF POTENTIAL 03 STORIED OFFICE BUILDING WITH 02 BASEMENT OF IFC, SHER-E-BANGLA NAGAR

DHAKA, BANGLADESH.
Date: August 10, 2018

SL Description of item QTY UNIT RATE AMOUNT

PART A- CIVIL
1 Dismantling of existing structures including foundation,column, beam,grade beam, slab and all
other element such as partition wall, plumbing fixtures,collecting rubbish and debrishes,
removal of the the rubish from the site and dumping into away from the site. 1.00 Job Tk. 150,000.00 Tk. 150,000.00

2 Earth work in excavation in all kinds of soil for foundation trenches including. layout, providing
center lines, local bench-mark pillars, leveling, ramming and preparing the base, fixing
bamboo spikes and marking layout with chalk powder, providing necessary tools and plants,
protecting and maintaining the trench dry etc., stacking, cleaning the excavated earth at a safe
distance out of the area enclosed by the layout etc. all complete and accepted by the
Engineer, subject to submit method statement of carrying out excavation work to the Engineer
for approval. However, Engineer’s approval shall not relieve the contractor of his
responsibilities and obligations under the contract.
Layout and marking for earthwork in excavation in foundation accepted by the Engineer.
[Plinth area of the structure shall be considered for measurement]

2.1 Layout 852.59 sqm Tk. 15.00 Tk. 12,788.85

2.2 Earthwork in excavation in foundation trenches up to 1.5 m depth and maximum 10 m lead: in
1278.89 cum Tk. 88.00 Tk. 112,542.32
soft clayey soil / loose sand / silt
2.3 Extra rate for each additional 0.5 meter depth exceeding 1.5 meter. 426.29 cum Tk. 108.00 Tk. 46,039.32
2.4 Extra rate for each additional 0.5 meter depth exceeding 1.5 meter. 426.29 cum Tk. 128.00 Tk. 54,565.12
2.5 Extra rate for each additional 0.5 meter depth exceeding 1.5 meter. 426.29 cum Tk. 148.00 Tk. 63,090.92
2.6 Extra rate for each additional 0.5 meter depth exceeding 1.5 meter. 426.29 cum Tk. 168.00 Tk. 71,616.72
2.7 Extra rate for each additional 0.5 meter depth exceeding 1.5 meter. 426.29 cum Tk. 188.00 Tk. 80,142.52
2.8 Extra rate for each additional 0.5 meter depth exceeding 1.5 meter. 426.29 cum Tk. 208.00 Tk. 88,668.32
2.9 Extra rate for each additional 0.5 meter depth exceeding 1.5 meter. 426.29 cum Tk. 228.00 Tk. 97,194.12
2.10 Extra rate for each additional 0.5 meter depth exceeding 1.5 meter. 426.29 cum Tk. 248.00 Tk. 105,719.92
2.11 Extra rate for each additional 0.5 meter depth exceeding 1.5 meter. 426.29 cum Tk. 268.00 Tk. 114,245.72
2.12 Extra rate for each additional 0.5 meter depth exceeding 1.5 meter. 426.29 cum Tk. 288.00 Tk. 122,771.52
2.13 Extra rate for each additional 0.5 meter depth exceeding 1.5 meter. 426.29 cum Tk. 308.00 Tk. 131,297.32
2.14 Mass concrete (1:3:6) in foundation or floor with cement, sand (F.M. 1.2) and picked jhama
chips including breaking chips, screening, mixing, laying, compacting to levels and curing for
at least 7 days including the supply of water, electricity and other charges and costs of tools 63.94 cum Tk. 6,647.00 Tk. 425,009.18
and plants etc. all complete and accepted by the Engineer. (Cement: CEM-II/A-M)

3 Boring/drilling for cast in situ pile up to the required depth and diameter with minimum
6 m long temporary steel casing, true to vertical, providing bentonite slurry and
maintaining water level in the hole, washing the hole for at least 30 minutes, clean
the bore-hole and make the bore- hole ready for placing steel cage and concreting
including hire charge of rig set with winch machine, tripod stand, trimie pipe, cost of
fuel, lubricant, mobilization, demobilization, maintenance, spares, stand-byes,
insurance coverage, water, electricity and other charges all compete approved and
accepted by the Engineer. Before commencing boring operation Contractor shall
submit the method statement of cast-in-situ pile work including sequence of boring 5280.00 rm Tk. 1,167.00 Tk. 6,161,760.00
and casting, disposal of spoils, test result of materials to the Engineer for approval.
However, Engineer’s approval shall not relieve the Contractor of his responsibilities
and obligations under contract.
600 mm dia
Depth up to 22 m

4 Removing of spoils / mud accumulated during boring for cast in situ pile by wash boring from
working site to a safe distance by contractors own arrangement i.e. with container set in truck
or on cart including loading, unloading everything complete as per standard practice. (Quantity 1542.00 cum Tk. 557.00 Tk. 858,894.00
should be given three times of solid volume of boring)

5 Cast in situ pile with reinforced cement concrete works of high slump by adding high range
water reducing admixture (ASTM C494 Type A or F complying item 7.20.1 or 7.20.6) with
minimum cement content relates to mix ratio 1 : 1.5 : 3 having minimum f'cr = 30 Mpa, and
satisfying a specified compressive strength f’c = 22 Mpa at 28 days on standard cylinders as
per standard practice of Code ACI/BNBC/ASTM & cement conforming to BDS EN-197-1-
CEM1, 52.5N (52.5MPa) / ASTM-C 150 Type – I, best quality coarse sand [Sylhet sand or
coarse sand of equivalent F.M.2.2], 20 mm down well graded crushed stone chips conforming
to ASTM C-33, including breaking chips, screening through proper sieves, making, placing re-
bar cage in position, placing and removing tri-pod as per requirement, pouring the concrete in 1542.00 cum Tk. 13,463.00 Tk. 20,759,946.00
bore-hole with the help of a trimie pipe, maintaining the trimie pipe immersed in concrete by at
least 1 meter throughout the period of concreting, maintaining required slump, etc. mixing the
aggregates with standard mixer machine with hoper, casting in forms, all complete including
water, electricity, testing of materials and concrete etc and other charges as per design,
drawing etc all complete approved and accepted by the Engineer. (Rate is excluding the cost
of reinforcement and its fabrication, binding, welding , placing and admixture ( approx doses
150 to 250ltr per bag of cement which to fix by mix design) )
 SL Description of item QTY UNIT RATE AMOUNT
6 Providing and making point welding at contact point of the spiral binders at reasonable
intervals with the main reinforcements by electric arc welding for construction of cast in situ
bored pile carefully with highly oxidized electrodes making the points prominent and accepted 653110.00 nos Tk. 3.00 Tk. 1,959,330.00
by the Engineer (rate is inclusive of all materials labour, tools and plants, electricity and all
equipment).

7 Reinforced cement concrete works using steel shutter with minimum cement content relates to
mix ratio 1:1.25:2.5 having minimum f'cr = 27 Mpa, and satisfying a specified compressive
strength f’c = 25 Mpa at 28 days on standard cylinders as per standard practice of Code
ACI/BNBC/ASTM & Cement conforming to BDS EN-197-1- CEM1, 52.5N (52.5MPa) / ASTM-
C 150 Type – I, best quality Sylhet sand or coarse sand of equivalent F.M. 2.2 and 20 mm
down well graded stone chips conforming to ASTM C-33, making, placing shutter in position
and maintaining true to plumb, making shutter water-tight properly, placing reinforcement in
position; mixing with standard mixer machine with hopper, fed by standard measuring boxes,
casting in forms, compacting by vibrator machine and curing at least for 28 days, removing
centering-shuttering after specified time approved; including cost of water, electricity,
additional testing charges of materials and cylinders required by engineer, other charges etc.
all complete approved and accepted by the Engineer.
(Rate is excluding the cost of reinforcement and its fabrication, placing and
binding etc)
Tie beam and lintels : over shore pile

7.1 Concrete 76.00 cum Tk. 12,154.00 Tk. 923,704.00

7.2 Formwork & shuttering 182.00 sqm Tk. 391.00 Tk. 71,162.00
8 Reinforced cement concrete works using steel shutter with minimum cement content relates to
mix ratio 1:1.25:2.5 having minimum f'cr = 40 Mpa, and satisfying a specified compressive
strength f’c = 32 Mpa at 28 days on standard cylinders as per standard practice of Code
ACI/BNBC/ASTM & Cement conforming to BDS EN-197-1- CEM1, 52.5N (52.5MPa) / ASTM-
C 150 Type – I, best quality Sylhet sand or coarse sand of equivalent F.M. 2.2 and 20 mm
down well graded stone chips conforming to ASTM C-33, making, placing shutter in position
and maintaining true to plumb, making shutter water-tight properly, placing reinforcement in
position; mixing with standard mixer machine with hopper, fed by standard measuring boxes,
casting in forms, compacting by vibrator machine and curing at least for 28 days, removing
centering-shuttering after specified time approved; including cost of water, electricity,
additional testing charges of materials and cylinders required by engineer, other charges etc.
all complete approved and accepted by the Engineer. (Rate is excluding the cost of
reinforcement and its fabrication, placing and
binding etc)
In Raft/Basement Floor 02

8.1 Concrete 639.44 cum Tk. 12,154.00 Tk. 7,771,753.76

8.2 Formwork & shuttering 110.43 sqm Tk. 434.00 Tk. 47,926.62
9 Reinforced cement concrete works using steel shutter with minimum cement content relates to
mix ratio 1:1.25:2.5 having minimum f'cr = 40 Mpa, and satisfying a specified compressive
strength f’c = 32 Mpa at 28 days on standard cylinders as per standard practice of Code
ACI/BNBC/ASTM & Cement conforming to BDS EN-197-1- CEM1, 52.5N (52.5MPa) / ASTM-
C 150 Type – I, best quality Sylhet sand or coarse sand of equivalent F.M. 2.2 and 20 mm
down well graded stone chips conforming to ASTM C-33, making, placing shutter in position
and maintaining true to plumb, making shutter water-tight properly, placing reinforcement in
position; mixing with standard mixer machine with hopper, fed by standard measuring boxes,
casting in forms, compacting by vibrator machine and curing at least for 28 days, removing
centering-shuttering after specified time approved; including cost of water, electricity,
additional testing charges of materials and cylinders required by engineer, other charges etc.
all complete approved and accepted by the Engineer. (Rate is excluding the cost of
reinforcement and its fabrication, placing and binding etc)

9.1 Padestals, column, column capitals, lift walls and walls

9.1.1 Upto Basement-01 at Basement floor 02.
9.1.1.1 Concrete 170.11 cum Tk. 12,367.00 Tk. 2,103,750.37
9.1.1.2 Formwork 1141.26 sqm Tk. 408.00 Tk. 465,634.08
9.1.2 Upto Ground Floor at Basement floor 01
9.1.2.1 Concrete 170.11 cum Tk. 12,367.00 Tk. 2,103,750.37
9.1.2.2 Formwork 1141.26 sqm Tk. 408.00 Tk. 465,634.08
9.2 Tee beams, Ell beams and Rectangular beams etc
9.2.1 Basement Floor 01
9.2.1.1 Concrete 14.75 cum Tk. 12,240.00 Tk. 180,540.00
9.2.1.2 Formwork 96.63 sqm Tk. 408.00 Tk. 39,425.04
9.2.3 Floor and Roof slab
9.2.3.1 Basement Floor 01
9.2.3.1 Concrete 189.92 cum Tk. 12,240.00 Tk. 2,324,620.80
9.2.3.2 Formwork 775.09 sqm Tk. 532.00 Tk. 412,347.88
9.3 Stair case slab and steps
9.3.1 Basement Floor 01
9.3.2.1 Concrete 1.34 cum Tk. 12,240.00 Tk. 16,401.60
9.3.1.2 Formwork 21.59 sqm Tk. 437.00 Tk. 9,434.83
 SL Description of item QTY UNIT RATE AMOUNT
10 Reinforced cement concrete works using steel shutter with minimum cement content relates to
mix ratio 1:1.25:2.5 having minimum f'cr = 30 Mpa, and satisfying a specified compressive
strength f’c = 25 Mpa at 28 days on standard cylinders as per standard practice of Code
ACI/BNBC/ASTM & Cement conforming to BDS EN-197-1- CEM1, 52.5N (52.5MPa) / ASTM-
C 150 Type – I, best quality Sylhet sand or coarse sand of equivalent F.M. 2.2 and 20 mm
down well graded stone chips conforming to ASTM C-33, making, placing shutter in position
and maintaining true to plumb, making shutter water-tight properly, placing reinforcement in
position; mixing with standard mixer machine with hopper, fed by standard measuring boxes,
casting in forms, compacting by vibrator machine and curing at least for 28 days, removing
centering-shuttering after specified time approved; including cost of water, electricity,
additional testing charges of materials and cylinders required by engineer, other charges etc.
all complete approved and accepted by the Engineer.
(Rate is excluding the cost of reinforcement and its fabrication, placing and
binding etc)

10.1 Padestals, column, column capitals, lift walls and walls

10.1.1 Ground Floor
10.1.1.1 Concrete 34.02 cum Tk. 12,348.00 Tk. 420,078.96
10.1.1.2 Formwork & shuttering 288.90 sqm Tk. 408.00 Tk. 117,871.20
10.1.2 1st floor
10.1.2.1 Concrete 29.16 cum Tk. 12,456.00 Tk. 363,216.96
10.1.2.2 Formwork & shuttering 247.62 sqm Tk. 449.00 Tk. 111,181.38
10.1.3 2nd Floor
10.1.3.1 Concrete 29.16 cum Tk. 12,564.00 Tk. 366,366.24
10.1.3.2 Formwork & shuttering 247.62 sqm Tk. 490.00 Tk. 121,333.80
10.1.4 Roof
10.1.4.1 Concrete 29.16 cum Tk. 12,672.00 Tk. 369,515.52
10.1.4.2 Formwork & shuttering 247.62 sqm Tk. 531.00 Tk. 131,486.22
10.2 Tee beams, Ell beams and Rectangular beams etc
10.2.1 Ground Floor
10.2.1.1 Concrete 8.35 cum Tk. 12,348.00 Tk. 103,105.80
10.2.1.2 Formwork & shuttering 55.03 sqm Tk. 419.00 Tk. 23,057.57
10.2.2 1st Floor
10.2.2.1 Concrete 28.76 cum Tk. 12,456.00 Tk. 358,234.56
10.2.2.2 Formwork & shuttering 188.69 sqm Tk. 460.00 Tk. 86,797.40
10.2.3 2nd Floor
10.2.3.1 Concrete 28.76 cum Tk. 12,564.00 Tk. 361,340.64
10.2.3.2 Formwork & shuttering 188.69 sqm Tk. 501.00 Tk. 94,533.69
10.2.4 Roof
10.2.4.1 Concrete 28.76 cum Tk. 12,672.00 Tk. 364,446.72
10.2.4.2 Formwork & shuttering 188.69 sqm Tk. 542.00 Tk. 102,269.98
10.3 Floor and roof slab
10.3.1 Ground Floor
10.3.1.1 Concrete 194.51 cum Tk. 12,240.00 Tk. 2,380,802.40
10.3.1.2 Formwork & shuttering 826.95 sqm Tk. 532.00 Tk. 439,937.40
10.3.2 1st Floor
10.3.2.1 Concrete 172.80 cum Tk. 12,348.00 Tk. 2,133,734.40
10.3.2.2 Formwork & shuttering 745.20 sqm Tk. 573.00 Tk. 426,999.60
10.3.3 2nd Floor
10.3.3.1 Concrete 172.80 cum Tk. 12,456.00 Tk. 2,152,396.80
10.3.3.2 Formwork & shuttering 745.20 sqm Tk. 614.00 Tk. 457,552.80
10.3.4 Roof Floor
10.3.4.1 Concrete 172.80 sqm Tk. 12,564.00 Tk. 2,171,059.20
10.3.4.2 Formwork & shuttering 745.20 sqm Tk. 655.00 Tk. 488,106.00
10.4 Stair case slab and steps
10.4.1 G. Floor
10.4.1.1 concrete 1.34 cum Tk. 12,240.00 Tk. 16,401.60
10.4.1.2 Formwork & shuttering 21.59 sqm Tk. 437.00 Tk. 9,434.83
10.4.2 1st Floor
10.4.2.1 Concrete 1.34 cum Tk. 12,348.00 Tk. 16,546.32
10.4.2.2 Formwork & shuttering 21.59 sqm Tk. 478.00 Tk. 10,320.02
10.4.3 2nd Floor
10.4.3.1 Concrete 1.34 sqm Tk. 12,456.00 Tk. 16,691.04
10.4.3.2 Formwork & shuttering 21.59 sqm Tk. 519.00 Tk. 11,205.21
10.4.4 Roof Floor
10.4.4.1 Concrete 1.34 cum Tk. 12,564.00 Tk. 16,835.76
10.4.4.2 Formwork & shuttering 21.59 sqm Tk. 560.00 Tk. 12,090.40
 SL Description of item QTY UNIT RATE AMOUNT
11 Reinforced cement concrete works with minimum cement content relates to mix ratio
1:2:4 having minimum f'cr = 27 MPa, satisfying a specified compressive strength f'c = 22
MPa at 28 days on standard cylinders as per standard practice of Code ACI/BNBC/ASTM,
cement conforming to BDS EN-197-1-CEM-I, 52.5N (52.5 MPa) / ASTM-C 150 Type – I, best
quality Sylhet sand or coarse sand of equivalent F.M. 2.2 and 20 mm down well
graded stone chips conforming to ASTM C-33, making and placing shutter in position
maintaining true to plumb, making shutter water-tight properly, placing reinforcement in
position; mixing in standard mixer machine with hopper fed by standard measuring boxes or
mixing in batching plant, casting in forms, compacting by vibrator machine and curing at least
for 28 days, removing centering-shuttering after specified time approved; including
cost of water, electricity, laboratory testing charges of materials and concrete cylinders as
required, cost of all materials and other charges etc. all complete, approved and accepted by
the Engineer-in-charge. (Rate is excluding the cost of reinforcement and its fabrication,
placing, binding etc. and the cost of shuttering & centering)

11.1 Lintel
11.1.1 Concrete 3.00 cum Tk. 12,564.00 Tk. 37,692.00
11.1.2 Formwork 23.24 sqm Tk. 560.00 Tk. 13,014.40
11.2 Work Top Slab
11.2.1 Concrete 0.50 cum Tk. 12,564.00 Tk. 6,282.00
11.2.2 Formwork 6.63 sqm Tk. 560.00 Tk. 3,712.80
12 Grade 400 (RB 400 / 400W: complying BDS ISO 6935-2:2006) ribbed or deformed bar
produced and marked according to Bangladesh Standard, with minimum yield strength, fy
(ReH)= 400 Mpa but fy not exceeding 418MPa and what ever is the yield strength within
allowable limit as per BNBC sec 8.3.3.5 /ACI 318-11 sec 21.1.5.2, the ratio ultimate tensile
415000.00 kg Tk. 81.00 Tk. 33,615,000.00
strength fu to yield strength fy, shall be at least 1.25 and minimum elongation after fracture
and minimum total elongation at maximum force is 16% and 8% respectively

14 Water-proofing membrane on external surface of primed vertical or inclined wall /on plastered
and primed back-wall and concrete cast against membrane.
(Excluding cost of back fill/brick wall on back/plaster when membrane laid on back-wall and 883.50 sqm Tk. 956.00 Tk. 844,626.00
concrete cast against membrane which to be paid as per corresponding items in this schedule)

13 125 mm brick works with first class bricks with cement sand (F.M. 1.2) mortar (1:4) and making
bond with connected walls including necessary scaffolding, raking out joints, cleaning and
soaking the bricks for at least 24 hours before use and washing of sand, curing at least for 7
days in all floors including cost of water, electricity and other charges etc. all complete and 1208.83 sqm Tk. 798.00 Tk. 964,646.34
accepted by the Engineer-in-charge. (Cement: CEM-II/A-M)

16 Brick works of width one brick or one and a half brick length of first class bricks with cement
sand (F.M. 1.2) mortar (1:6) in superstructure including raking out joints, filling the interstices
with mortar, cleaning and soaking the bricks at least for 24 hours before use and washing of
sand, necessary scaffolding, curing at least for 7 days etc. all complete (measurement to given
226.74 cum Tk. 6,785.00 Tk. 1,538,430.90
as 250 mm width for one brick length and 375 mm for one brick and a half brick length) and
accepted by the Engineer-in-charge. (Cement: CEM-II/A-M)

15 Minimum 12 mm thick cement sand (F.M. 1.2) plaster (1:6) having with fresh cement to wall
both inner-and outer surface, finishing the corner and edges including washing of sand
cleaning the surface, scaffolding and curing at least for 7 days, cost of water, electricity and 2699.50 sqm Tk. 243.00 Tk. 655,978.50
other charges etc. all complete in all respect as per drawing and accepted by the Engineer.
(Cement: CEM-II/A-M)

25 mm thick artificial patent stone (1:2:4) flooring with cement, best quality coarse sand (50%
quantity of Sylhet sand or coarse sand of equivalent F.M. 2.2 and 50% best
quality local sand of FM 1.2) and 12 mm down well graded brick chips including breaking
chips, screening, laying the concrete in alternate panels, compacting and finishing the top with
neat cement and curing at least for 7 days in all floors including cost of water, electricity and 464.75 sqm Tk. 451.85 Tk. 209,997.29
other charges etc. all complete and accepted by the Engineer-in-charge.
(Cement: CEM-II/A-M)

14 Clearing and disposing of excavated earth from the construction site by truck or any other
means to a place within 30 km radius of the city or town area including loading, unloading at
both ends, leveling and dressing the carried earth etc. complete accepted by the Engineer. 8318.00 cum Tk. 457.00 Tk. 3,801,326.00

Sub total of part A Tk. 104,297,363.95

SL Description of item QTY UNIT RATE AMOUNT
PART B- EXTERNAL AND INTERNAL FINISHING WORK
1 Supplying, fitting and fixing country made GP(Gress Porcellanto) - glazed or unglazed
homogeneous floor tiles complying BDS ISO 13006: 2015, water absorbtion ≤ 0.5%,
modulus of rupture (MOR) ≥ 27 N/mm2, irrespective of color &/or design, with
cement sand (F.M. 1.2) mortar (1:4) base and raking out the joints with white
cement including cutting and laying the tiles in proper way and finishing with care
etc. all complete and accepted by the Engineer-in-charge. (Cement: CEM-II/A-M).

1.1 GP (homogeneous) 300 mm x 300 mm floor tiles 116.19 sqm Tk. 2,151.68 Tk. 250,003.70
1.2 GP (Homogenous) 400 mm X 400 mm Floor Tiles 339.30 sqm Tk. 2,452.00 Tk. 831,963.60
1.3 GP (Homogenous) 600 mm X 600 mm Floor Tiles 1914.78 sqm Tk. 2,775.66 Tk. 5,314,778.25
SL Description of item QTY UNIT RATE AMOUNT
2 Supplying, fitting and fixing country made glazed wall tiles complying BDS ISO
13006: 2015, respective of color &/or design, with 20 mm thick cement sand (F.M.
1.2) mortar (1:3) base and raking out the joints with white cement including cutting,
laying and hire charge of machine and finishing with care etc. including cost of
water, electricity and other charges complete in all respect and accepted by the
Engineer-in-charge. (Cement: CEMII/A-M).

2.1 Wall tiles more than 250 mm x 400 mm & less than or equal to 300 mm x 600 mm in
sizes 316.03 sqm Tk. 2,366.85 Tk. 747,995.61

3 Supplying, fitting and fixing country made rustic or matt finished stair tiles
complyingBDS ISO 13006: 2015, water absorbtion ≤ 0.5%, modulus of rupture
(MOR) ≥ 27N/mm2, irrespective of color &/or design, with 20 mm thick cement
sand (F.M. 1.2)
mortar (1:3) base and raking out the joints with white cement including cutting,
laying and hire charge of machine and finishing with care etc. including water,
electricity and other charges complete in all respect and accepted by the Engineer-
in-charge. (Cement: CEMII/A-M).

3.1 Rustic stair tiles of size 300 mm x 600 mm 144.81 sqm Tk. 2,420.64 Tk. 350,532.88
4 Raising of Office floor by 6" From existing on RCC floor with Steel grid frame of
4"X4" MS box, 2"X2" MS box Post and 1.5"X2" MS box Bracing with 6mm MS plate
and 1.5mm MS plate with anti corrosive paint with 10mm/20mm best quality
rubber gasket 27.89 sqm Tk. 9,198.43 Tk. 256,544.21
suspension with 2" RCC slab with 8mm rebar and brick chips all complete with 2
coats water proofing chemical proofing with BASF all complete.

5 Supplying, fitting and fixing 20mm to 25mm thick machine made cement pavement
tiles having minimum compressive strength of 27 MPa, irrespective of color &/or
design, with 20 mm thick cement sand (F.M. 1.2) mortar (1:4) base and making the
joints carefully in true staight line including cutting, laying and hire charge of
machine and finishing withcare etc. including water, electricity and other charges
complete in all respect and accepted by the Engineer-in-charge. (Cement: CEM-II/A-
M).

5.1 Pavement tiles of size 300 mm x 300 mm 698.13 sqm Tk. 2,481.00 Tk. 1,732,060.53
6 Supplying, fitting and fixing of aluminium sliding doors as per the U.S. Architectural
Aluminium Manufacturer’s Association (AAMA) standard specification and BDS
1879:2014 having 1.2 mm thick outer bottom (size 75.50 mm, 17.79 mm, 0.528
kg/m), 1.2 mm thick outer top (size 75.50 mm, 26.80 mm, 0.78 kg/m) 1.2 mm thick
shutter top (size 33 mm, 26.80 mm, 0.536 kg/m), 1.2 mm shutter bottom (size 60
mm, 24 mm, 0.736 kg/m), 1.2 mm thick outer side(size 75.50 mm, 19.90 mm, 0.616
kg/m) 1.5 mm thick shutter lock (size 49.20 mm, 26.20 mm, 0.661 kg/m), 1.2 mm
thick inter lock (size 34.40 mm, 32.10 mm, 0.665 kg/m), 1.2 mm thick shutter
divider (size 31.75 mm, 0.535 kg/m) sections all aluminum members (Total eight
14.789 kg) will be anodized to aluminium bronze/silver/ss/black colour with a coat
not less than 15 micrones in thickness or powder coated to any colour with a coat
not less than 25 micrones in thickness and density of 4 mg per square cm etc.
including all accessories like handle, sliding door key lock , sliding door wheel, sliding 883.00 sqm Tk. 5,541.00 Tk. 4,892,703.00
door mohiar, sliding door neoprene, bolts and nuts including sealants, keeping
provision for fitting 5mm thick glass including labour charge for fitting of
accessories, making grooves and mending good damages, carriage, and electricity
complete in all respect as per drawing and accepted by the Engineer-in-charge.
Size up to: 2100 mm x 2100 mm

7 Supplying, fitting and fixing in Aluminium door frames, windows, partitions and
curtain wall distortion free glass of approved quality and shade including cost of
fitting fixing all necessary accessories etc. complete in all respect as per drawing and 1329.00 sqm Tk. 7,961.22 Tk. 10,580,461.38
accepted by the Engineer-in-charge.
SL Description of item QTY UNIT RATE AMOUNT
8 Supplying, fitting and fixing of aluminium composite swing doors with fixed
partition as per the U. S. Architectural Aluminium Manufacturer’s Association
(AAMA) standard specification and BDS 1879:2014 having 1.5 mm thick wall frame
(size 101.60, 44.45 mm, 0.86 kg/m), 1.8 mm thick shutter side (size 54 mm, 46 mm,
1.2 kg/m ), 1 mm thick door glass bit (size 16.54 mm, 14. 49 mm, 0.115 kg/m), 1.8
mm thick closure section (size 101.54 mm, 42.93 mm, 1.20 kg/m), 1.5 thick closure
cover (101.60 mm, 0.45 kg/m), 4 mm thick floor bottom (size 101.60 mm, 12.70
mm, 1 kg/m), 1.8 mm thick shutter bottom (size 86.60 mm, 43.99 mm , 0.60 kg/m),
1.8 mm thick shutter top (size 51 mm, 43.99 mm, 1.88 kg/m) 2.3mm to 4.01mm
thick handle (short) (size 101.60 mm, 38.10 mm, 25.40 mm, 1.35 kg/m), 1.5 mm
thick top and side (size 101.60 mm, 44.45 mm, 1.3 kg/m), 1.50 mm thick bottom
(size 101.35 mm, 44.45 mm, 1.10 kg/m), 1.50 mm thick bottom cover (44.32 mm,
19.61mm, 0.392 kg/m), 1.50 mm thick grouve cover (size 83.21 mm, 16.00 mm,
0.57 kg/m), 0.99 mm thick fixed glass protector (size 39.09 mm, 14.81 mm, 0.188
kg/m), 0.99 mm thick fixed glass protector bit (size 15.75 mm, 14.81 mm, 0.13
kg/m) section of all aluminum members will be anodized to aluminium
ronze/silver/ss/black colour with a coat not less than 15 micrones in thickness or
powder coated to any colour with a coat not less than 25 micrones in thickness and 92.95 sqm Tk. 11,834.24 Tk. 1,099,992.61
density of 4 mg per square cm etc. (Total weight min 69.699 kg) keeping provision
for 5 mm of glass panes with cost including all accessories like swing door clouser,
swing door lock , swing door mohair, flush bolt , bolts and nuts including sealants,
labour charge for fitting , fixing by angles, screws, mohiar, washer, machinery, cost of
fabrication, making the grooves, mending good the damages, electricity etc.
complete in all respect as per drawing and accepted by the Engineer-in-charge.

9 Supplying , fitting & fixing of Imported double leaf tempered glass

door with all imported fittings and nickel plated handles 60" double swing frameless
10mm Tempered glass door for entry as per design. 4.00 nos Tk. 16,500.00 Tk. 66,000.00

10 Supply and fittin at site of HDF laminated Toilet partition works sytem with doors
made with 12mm HDF board ( Grade A-beech/ gray colour) on SS fittings (304) and
Q vical SS channel, all best qualitiues legs and accessories all complete inclusive of 106.90 nos Tk. 11,296.32 Tk. 1,207,576.61
labour and materials

11 Supplying, fitting and fixing 36 mm thick and having density 400 kg/cum solid
particle board single leaf flush door for all floors for internal use made of well
matured mechanical seasoned Rubber (Malaysian timber) or other approved
wooden frame having finished size 35 mm x 50 mm around upon which 1.2 mm
thick veneer (total two nos of veneers one of 0.7 mm horizontally made of garjon
and another of 0.5 mm vertically made of Burma Teak or Champa or Chapalish or
Garjan wood) are pested on each side by mechanized process and provided with
best quality 4 (four) nos 100 mm long iron hinges, 2 (two) nos best quality 12 mm 36.27 sqm Tk. 4,989.00 Tk. 180,951.03
dia 250 mm and 200 mm long iron tower and socket bolts, 2 (two) nos heavy type
nickel plated handles, hinged cleats, buffer blocks, necessary screws etc. all
complete and accepted by the Engineer-in-charge
SL Description of item QTY UNIT RATE AMOUNT
12 Supply and installation of fire rated door complete and accepted by the Engineer-
incharge with the following specification:
Standard(s) for safety : UL Certified, NFPA 80 standard
ANSI / UL 10C: Positive pressure of fire tests of door assemblies.
ANSI / UL 10B: Fire tests of door assemblies.
UL Subject 63: Outline of investigation for fire frames.
Shutter materials: Mild steel.
Fire resistivity (door and frame): Two hours.
Fire resistivity (accessories): Three hours (panic bar, pul handle, ceramic fibre tape
for sealing smoke, hinge, bolt and screw, mortice lock, door closer
Door frame: 2 vertical fire resisting jamb and 1 fire resisting horizontal jamb made
with single rabbet hollow steel chanel frame made of 2.3 mm imported cold rolled
mild steel sheet. Four SS hinges (size: 112 mm x 100 mm x 3.4mm) are used on each
leaf screwd with frame
Door leaf: Door leaf faces consists of 1.6 mm thick imported cold rolled MS sheet
attached
together using interlocking mechanism and tack welding which is filled with 7.16 sqm Tk. 48,217.00 Tk. 345,233.72
imported
100kg/m3 rock wool cake. Stiffeners should be used inside to strengthen structure.
Vision Panel: Made of UL certified 5 mm glass. It has clear vision area of 150 mm x
100
mm. Its frame is mae of 1.6 mm imported cold rolled MS sheet and SS pop rivet
used for
fixing. Ceramic fibre tape is used for sealing smoke.

13 Supplying, fitting and fixing of 0.6 mm thick best quality perforated aluminium metal
board false ceiling of size 600 mm x 600 mm, powder coated of approved design,
inner side is coverd by black tissue/ fabric to protect the hole from air circulation,
framing by aluminium T-bar of natural anodized finish suspended in 600 mm x 600
mm grid from ceiling by 12 SWG double ply wire, fixed to the ceiling by rowel plug,
screws, hooks, nails etc., maintaining straight lines and desired finished level at
bottom face including vertical wooden strut as required, making holes in slabs or
beams by electric drill machine andmending good the damages, if any during
execution of the work, also including cost of all materials, electricity, accessories, 1496.00 sqm Tk. 2,676.00 Tk. 4,003,296.00
scaffoldings, labour for installation, screws, nails, etc. all complete as per drawing,
design and accepted by the Engineer-in-charge.

14 Supplying, fitting and fixing veneered board ceiling of 12 mm thick board laminated
bymechanical hot press with a milk white PVC membrane, framing by aluminium T-
bar of natural anodized finish suspended in 600 mm x 600 mm grid from ceiling by
12 SWG double ply wire, fixed to the ceiling by rowel plug, screws, hooks, nails etc.,
maintaining straight lines and desired finished level at bottom face including vertical
wooden strut as required, making holes in slabs or beams by electric drill machine
and mending good the damages, if any during execution of the work, also including
cost of all materials, electricity, accessories, scaffoldings, labour for installation,
screws, nails, etc. all complete as per drawing, design and accepted by the Engineer-
in-charge.

With Ducco Sprayed finish 604.20 sqm Tk. 4,249.00 Tk. 2,567,245.80
With Plastic painted finish 265.00 sqm Tk. 2,690.00 Tk. 712,850.00
15 Supplying, fitting and fixing of best quality 6 mm thick PVC board false ceiling of size
600 mm x 600 mm of approved design, minimumn PVC content of 35%, framing
byaluminium T-bar of natural anodized finish suspended in 600 mm x 600 mm grid
from ceiling by 12 SWG double ply wire, fixed to the ceiling by rowel plug, screws,
hooks, nails etc., maintaining straight lines and desired finished level at bottom face
including vertical wooden strut as required, making holes in slabs or beams by
electric drill machine and mending good the damages, if any during execution of the 116.20 sqm Tk. 3,711.65 Tk. 431,293.73
work, also including cost of all materials, electricity, accessories, scaffoldings, labour
for installation, screws, nails, etc. all
complete as per drawing, design and accepted by the Engineer-in-charge.
SL Description of item QTY UNIT RATE AMOUNT
16 Exterior premium acrylic emulsion paint of approved best quality and color with
high performance against dirt picking tendency and efflorosence resistence
properties along with water resisting properties and resistance properties against
fungi, fading and flaking from authorized local agent of the manufacturer (Berger
weather coat antidirt long life/ Elite master coat/ Asian apex ultima or equivalent
brand) in a sealed container; applying toexterior surface with surface preparation
including cleaning drying, making free from dirt, grease, wax, removing all chalked
and scaled materials, fungus, mending good the surface defects using sand paper
and necessary scaffolding; applying 1 coat of exterior sealer of specified brand on
prepared surface; then applying 1 coat of exterior putty of specified brand for
levelling, spot filling, crack filling and cutting by sand paper/zero water paper; finally 577.22 sqm Tk. 269.00 Tk. 155,272.18
applying 2 coats of exterior emulsion paint by spreading with brush/roller/spray
machine & necessary scaffolding etc. upto desired finishing, elapsing specified time
for drying or recoating; all complete in all floors and accepted by the Engineer-in-
charge.

17 Exterior premium acrylic emulsion paint of approved best quality and color with
high performance against dirt picking tendency and efflorosence resistence
properties along with water resisting properties and resistance properties against
fungi, fading and flaking from authorized local agent of the manufacturer (Berger
weather coat antidirt long life/ Elite master coat/ Asian apex ultima or equivalent
brand) in a sealed container; applying toexterior surface with surface preparation
including cleaning drying, making free from dirt, grease, wax, removing all chalked
and scaled materials, fungus, mending good the surface defects using sand paper
and necessary scaffolding; applying 1 coat of exterior sealer of specified brand on
prepared surface; then applying 1 coat of exterior putty of specified brand for
levelling, spot filling, crack filling and cutting by sand paper/zero water paper; finally 578.22 sqm Tk. 270.00 Tk. 156,119.40
applying 2 coats of exterior emulsion paint by spreading with brush/roller/spray
machine & necessary scaffolding etc. upto desired finishing, elapsing specified time
for drying or recoating; all complete in all floors and accepted by the Engineer-in-
charge.

18 Interior standard acrylic emulsion paint (plastic or matt finish) of approved best
quality and colour delivered from authorized local agent of the manufacturer
(Berger robbialac plastic emulsion/Asian apcolite plastic emulsion or equivalent
brand) in a sealed container; applying to interior wall and ceiling with surface
preparation including cleaning drying, making free from dirt, grease, wax, removing
all chalked and scaled materials, fungus, mending good the surface defects using
sand paper and necessary scaffolding; applying 1 coat of interior sealer of specified
brand on prepared surface; then applying 1 coat of interior putty of specified brand
for levelling, spot filling, crack filling and cutting by sand paper/zero water paper; 579.22 sqm Tk. 236.68 Tk. 137,089.79
finally applying 2 coats of interior emulsion paint by spreading with
brush/roller/spray machine & necessary scaffolding etc. upto desired finishing,
elapsing specified time for drying or recoating; all complete in all floors and
accepted by the Engineer-in-charge.

19 Supplying, fabrication and Installation of approved colour (4 mm thick) Aluminium

composite panel (Alucobond/Alcopanel/Alpolic) as per US Architectural Aluminium
Manufacturer's Association (AAMA) in column, beam and wall surface providing
with 44 mm x 44 mm x 1.5 mm aluminum section including supply of necessary
hardwares, consumables, scaffolding etc fitted with necessary accessories like rivet,
screw, rowel bolt etc. all complete in all respect as per drawing and direction of the 79.00 sqm Tk. 4,415.00 Tk. 348,785.00
Engineer-in-charge.
SL Description of item QTY UNIT RATE AMOUNT
20 Manufacturing, supplying, fitting and fixing of stair railing of standard height of any
design and shape with square box (2 nos. box in each tread) made by thorough
welding of 2 nos. 25 mm x 25 mm x 5 mm M.S. angle, engraving each box 150 mm
in the concrete by 50 mm x 50 mm x 6 mm anchor plate at base, welding 50 mm x
50 mm x 6 mm F.I. bar in inclined plain with the top of the box fitted in the grooved
wooden rail and 2 Nos. 225 mm x 25 mm finished section of wooden strip fitted and
fixed at mid height of railing at both side of M.S. angle box in inclined plain parallel
to the hand rail etc. fitted and fixed by necessary screws, nails including cutting
grooves in concrete, mending good the damages with cement concrete (1:2:4)
applying 1st class french polish to wooden hand rail and
inclined wooden strip and painting to F.I bar and square box with 2 (two) coats of 79.00 sqm Tk. 6,614.00 Tk. 522,506.00
synthetic enamel paint of approved quality and colour over a prime coat etc.
complete in all respect for all floors and accepted by the Engineer-in-charge.
(Exposed area of railing will be considered for measurement, rate is excluding the
cost of hand-rail and cost of painting)

21 Supplying, fitting and fixing verandah railing with 2 mm thick 50 mm dia SS hand
rail, 2 mm thick 20 mm dia 5 nos SS horizontal pipes, 2 mm thick 50 mm x 25 mm SS
box vertical post @ 450 mm c/c. Among the vertical box post 5 nos box posts will be
fitted with floor bed by 65 mm x 55 mm x 6 mm SS plate, remaining no SS box post
will be fitted and fixed with 50 mm x 25 mm x 2 mm SS horizontal box at bottom (50
mm above from floor bottom) including all fittings, fixtures, polishing, carrying etc. 76.22 sqm Tk. 3,067.00 Tk. 233,766.74
all complete as per approved design and drawing and accepted by the Engineer-in-
charge

Sub total of part B Tk. 37,125,021.77

SL Description of item QTY UNIT RATE AMOUNT
PART C- INTRENAL PLUMBING (WATER SUPPLY & SANITARY) SYSTEM
1 Water pump
1.1 Supplying, fitting and fixing of centrifugal water pump with complete with all
necessary fittings and connection approved and accepted by the Engineer. Pump
flow rate is 180-200 LPM and 20-25 meter head. Impeller have to brass metal and
high corrosive resistance. Motor have to single and three phase connection facility.
Approximate power 2.2 to 2.5 KW. Pump have to third party certified and efficient 2.00 Nos Tk. 40,000.00 Tk. 80,000.00
power consumption. Have to coverage warranty minimum 24 (Twenty Four) month.

1.2 Supplying, fitting and fixing of sump water pump with complete with all necessary
fittings and connection approved and accepted by the Engineer. Pump flow rate is
50-100 LPM and 8-12 meter head. Impeller have to brass metal and high corrosive
resistance. Motor have to single and three phase connection facility. Approximate
power 1.0 to 1.2 KW. Pump have to third party certified and efficient power 1.00 Nos Tk. 25,000.00 Tk. 25,000.00
consumption. Have to coverage warranty minimum 24 (Twenty Four) month.

2 Supplying, fitting and fixing European type glazed porcelain Combi closet, 755 X 385
X 415 mm (±10%) in size, approximately 30 kg (±10%) by weight in all floors
including making holes wherever required and mending good the damages and
fitting, fixing, finishing etc. complete with all necessary fittings and connection
approved and accepted by the Engineer. Have to third party certified and efficient
water consumption i.e maximum flash water consumption 0.5 to 1.5 litre. Have to 21.00 Each Tk. 35,000.00 Tk. 735,000.00
coverage warranty minimum 24 (Twenty Four) month.

3 Supplying, fitting and fixing Wall hung innogreen type glazed porcelain urinal, 430 X
445 X 1118 mm (±10%) in size, approximately 10 kg (±10%) by weight, plastic seat
cover and preparing the base with cement concrete and with wire mesh or rods if
necessary, in all floors including making holes wherever required and mending good
the damages and fitting, fixing, finishing etc. complete with all necessary fittings and
connection approved and accepted by the Engineer. Have to third party certified 12.00 Each Tk. 20,000.00 Tk. 240,000.00
and efficient water consumption i.e maximum flash water consumption 2.5 to 3
litre. Have to coverage warranty minimum 24 (Twenty Four) month.
SL Description of item QTY UNIT RATE AMOUNT
4 Supplying, fitting and fixing white glazed vitreous wall-hung lavatory with pedestal
and soap dispenser (Basin-600X500X235 mm and Pedestal- 260X275X360 mm)
(±10%) in size and 40 kg by weight the same in position with heavy type C.I.
Brackets. 35 mm dia PVC waste water pipe with brass coupling (not exceeding 750
mm in length), basin waste with chain plug including making holes in walls and
floors and fitting with wooden blocks, screws and mending good the damages,
finishing etc. all complete approved and accepted by the Engineer. Have to third 24.00 Each Tk. 10,000.00 Tk. 240,000.00
party certified and efficient water consumption. Have to coverage warranty
minimum 24 (Twenty Four) month.

5 Supplying, fitting and fixing of 450 x 600 mm size and 5 mm thick unframed super
quality mirror with hard boards at the back with all necessary fitting including
making holes in walls and mending good the damages with cement mortar (1:4) etc.
all complete approved and accepted by the Engineer. (Made in Japan or equivalent) 24.00 Each Tk. 1,000.00 Tk. 24,000.00

6 Supplying, fitting and fixing super quality 600 x 125 mm coloured glass (plate) shelf
having 5 mm thickness with fancy C.P. brackets, screws and frames including making
holes in walls and mending good the damages with cement mortar (1:4) etc. all 24.00 Each Tk. 1,500.00 Tk. 36,000.00
complete approved and accepted by the Engineer.

7 Supplying, fitting and fixing super quality C.P. Towel rail of 600 mm long and 20 mm
in dia with C.P. holder including making holes in walls and mending good the
damages with cement mortar (1:4) etc. all complete approved and accepted by the 24.00 Each Tk. 900.00 Tk. 21,600.00
Engineer.

8 Supplying, fitting and fixing of special coloured toilet paper holder Size (150 mm x
150 mm x 126 mm) including making holes in walls and mending good the damages
with cement mortar (1:4) etc. all complete approved and accepted by the Engineer. 35.00 Each Tk. 250.00 Tk. 8,750.00

9 Supplying, fitting and fixing 125 mm dia stainless steel floor grating in traps or in
drains including making holes in walls/floors and mending good the damages with
cement mortar (1:4) etc. all complete approved and accepted by the Engineer. 58.00 Each Tk. 500.00 Tk. 29,000.00

10 Supplying 100 mm inside diameter best quality uPVC B-grade rain water down pipe
fitting, fixed in position with head and shoes, bends, min.20 mm width F.I. Bar clamp
and nails, and including all accessories such as round grating/domed roof grating 30.49 rm Tk. 820.00 Tk. 25,000.00
bands, sockets approved and accepted by the Engineer

11 Supplying 200 mm inside dia best quality uPVC soil, waste and ventilation pipe
having specific gravity 1.35-1.45, wall thickness 3.4- 4.0 mm, and other physical,
chemical, thermal, fire resistivity properties etc. as per BSTI approved manufacturer
standards or ASTM, BS/ISO/IS standards fitted and fixed in position with sockets,
bends, with all accessories such as Round grating/domed roof grating bands, sockets
etc. approved and accepted by the Engineer (length: 6000 mm Each).thermal, fire
resistivity properties etc. as per BSTI approved manufacturer standards or ASTM,
BS/ISO/IS standards fitted and fixed in position with sockets, bends, of uPVC Pipe 15.24 rm Tk. 2,296.00 Tk. 35,000.00
with all accessories such as Round grating /domed roof grating bands, sockets etc.
approved and accepted by the Engineer (length: 6000 mm Each).

12 Supplying 150 mm inside dia best quality uPVC soil, waste and ventilation pipe
having specific gravity 1.35-1.45, wall thickness 3.4- 4.0 mm, and other physical,
chemical, thermal, fire resistivity properties etc. as per BSTI approved manufacturer
standards or ASTM, BS/ISO/IS standards fitted and fixed in position with sockets,
bends, with all accessories such as Round grating/domed roof grating bands, sockets
etc. approved and accepted by the Engineer (length: 6000 mm Each).thermal, fire
resistivity properties etc. as per BSTI approved manufacturer standards or ASTM,
BS/ISO/IS standards fitted and fixed in position with sockets, bends, of uPVC Pipe 54.88 rm Tk. 1,804.00 Tk. 99,000.00
with all accessories such as Round grating /domed roof grating bands, sockets etc.
approved and accepted by the Engineer (length: 6000 mm Each).

13 Supplying 100 mm inside dia best quality soil, waste and ventilation pipe having
specific gravity 1.35 - 1.45, wall thickness 4.5 mm - 5.2 mm, and other physical,
chemical, thermal, fire resistivity properties etc. as per BSTI approved manufacturer
standards or ASTM, BS/ISO/IS standards fitted and fixed in position with sockets,
bends, with all accessories such as Round grating/domed roof grating bands, sockets 146.34 rm Tk. 820.00 Tk. 120,000.00
etc. approved and accepted by the Engineer (length: 6000 mm Each).
SL Description of item QTY UNIT RATE AMOUNT
14 Supplying 50 mm inside dia best quality soil, waste and ventilation pipe having
specific gravity 1.35 - 1.45, wall thickness 4.5 mm - 5.2 mm, and other physical,
chemical, thermal, fire resistivity properties etc. as per BSTI approved manufacturer
standards or ASTM, BS/ISO/IS standards fitted and fixed in position with sockets,
bends, with all accessories such as Round grating/domed roof grating bands, sockets 6.10 rm Tk. 492.00 Tk. 3,000.00
etc. approved and accepted by the Engineer (length: 6000 mm Each).

15 Supplying 40 mm inside dia best quality soil, waste and ventilation pipe having
specific gravity 1.35 - 1.45, wall thickness 4.5 mm - 5.2 mm, and other physical,
chemical, thermal, fire resistivity properties etc. as per BSTI approved manufacturer
standards or ASTM, BS/ISO/IS standards fitted and fixed in position with sockets,
bends, with all accessories such as Round grating/domed roof grating bands, sockets 60.98 rm Tk. 410.00 Tk. 25,000.00
etc. approved and accepted by the Engineer (length: 6000 mm Each).

16 Supplying, fitting and fixing G.I. pipe conforming to the standard BS-1387 $ BDS-
1031,having chemical composition (in%) Caron 0.17-0.25, Manganese 0.95-1.20,
Sulphur 0.060 max, Phosphorous 0.060 max, Tensile properties: miminum Yield
Stength 188 MPa, minimum Tensile Strength 313 MPa and marking for a)
Manufacturer b) Material c) Wall thickness d) Nominal outside dia e) Intended use
etc. on the body of the pipe with all special fittings, such as bends, elbows, sockets,
reducing sockets, Tee, unions, jam-nuts etc. including cutting trenches where
necessary and fitting the same with earth duly rammed and fixing in walls with
holder bats and making hole in floors, walls and consequent mending good the
damages etc. all complete in all respects approved and accepted by the Engineer.
(Pipes manufactured by National Tubes Limited under Steel & Engineering rm
Corporation, Ministry of Industries. Government of Bangladesh shall be given
priority) a) 20 mm dia G.I. Pipe with wall thickness 2.65 mm, outside diameter min
26.5 mm, weight 1.70k/m, can withstand min 50 kg/cm2 hydraulic pressure.

16.1 50 mm dia G.I. Pipe with wall thickness 2.65 mm, outside diameter min 26.5 mm,
weight 1.70k/m, can withstand min 50 kg/cm2 hydraulic pressure 38.11 rm Tk. 984.00 Tk. 37,500.00

16.2 40 mm dia G.I. Pipe with wall thickness 3.25 mm, outside diameter min 33.3 mm,
weight 2.59 kg/m, can withstand min 50 kg/cm2 hydraulic pressure. 30.49 rm Tk. 787.20 Tk. 24,000.00

16.3 32 mm dia G.I. Pipe with wall thickness 3.25 mm, outside diameter min 33.3 mm,
weight 2.59 kg/m, can withstand min 50 kg/cm2 hydraulic pressure. 12.20 rm Tk. 656.00 Tk. 8,000.00

16.4 25 mm dia G.I. Pipe with wall thickness 3.25 mm, outside diameter min 47.9 mm,
weight 3.83 kg/m, can withstand min 50 kg/cm2 hydraulic pressure 60.98 rm Tk. 492.00 Tk. 30,000.00

16.5 18 mm dia G.I. Pipe with wall thickness 3.25 mm, outside diameter min 75.2 mm,
weight 6.15 kg/m, can withstand min 50 kg/cm2 hydraulic pressure. 24.39 rm Tk. 426.40 Tk. 10,400.00

16.6 12 mm dia G.I. Pipe with wall thickness 3.25 mm, outside diameter min 75.2 mm,
weight 6.15 kg/m, can withstand min 50 kg/cm2 hydraulic pressure. 36.59 rm Tk. 328.00 Tk. 12,000.00

17 Supplying, fitting and fixing best quality D.I. ball valve with sealant etc. complete
approved and accepted by the Engineer. Have to third party certified.Have to
coverage warranty minimum 24 (Twenty Four) month.

17.1 50 mm DI ball valve. 5.00 Nos Tk. 5,000.00 Tk. 25,000.00

17.2 40 mm DI bal valve. 4.00 Nos Tk. 4,000.00 Tk. 16,000.00
17.3 32 mm DI bal valve. 5.00 Nos Tk. 3,500.00 Tk. 17,500.00
17.4 25 mm DI bal valve. 17.00 Nos Tk. 2,900.00 Tk. 49,300.00
17.5 18 mm DI ball valve. 20.00 Nos Tk. 2,500.00 Tk. 50,000.00
18 Supplying different inside dia best quality uPVC pressure waste pipe having specific
gravity 1.35 -1.45, wall thickness 2.7 mm - 3.4 mm, and other physical, chemical,
thermal, fire resistivity properties etc. as per BSTI approved manufacturer standards
or ASTM, BS/ISO/IS standards, fitted and fixed in position with sockets, bends, with
all accessories such as Round grating/domed roof grating bands, sockets etc.
complete approved and accepted by the Engineer.

18.1 100 mm dia uPVC ‘P’ or ‘S’ trap 50.00 Nos Tk. 200.00 Tk. 10,000.00
19 Supplying, fitting and fixing medium best quality CP pillar cock etc. complete
approved and accepted by the Engineer 12 mm CP medium quality pillar cock. Have
to third party certified and lower water comption.Have to coverage warranty 24.00 Nos Tk. 2,000.00 Tk. 48,000.00
minimum 24 (Twenty Four) month.

20 Supplying, fitting and fixing Special/Fancy quality C.P. concealed/ Surface Angle stop
cock etc. complete approved and accepted by the Engineer. Special concealed heavy 21.00 Nos Tk. 300.00 Tk. 6,300.00
type angle stop cock
SL Description of item QTY UNIT RATE AMOUNT
21 Supply and fitting-fixing hand / push shower for Combi Closet
Moving type push shower 21.00 Nos Tk. 500.00 Tk. 10,500.00

22 Supplying, fitting fixing of food grade plastic overhead water reservoir tank including
all necessary fittings, hardware and consumables etc. all complete approved and
accepted by the Engineer. 5000 liter capacity. 1.00 Nos Tk. 12,000.00 Tk. 12,000.00

23 Construction of septic tank of different sizes with walls of brick work in cement
mortar (1:6) having a lining of minimum 125 mm R.C.C cast against the walls as per
approved type plan over a brick flat soling and 150 mm thick reinforced cement
concrete flooring (1:2:4) with 125 mm thick walls in partition and 12 mm thick
cement plaster (1:4) with N.C.F. to insides of walls on floor and all around outside
walls by 18" height at top including supplying fitting and fixing of two R.C.C. Tees
and providing 450 mm dia water sealed heavy type C.I. manhole cover with
locking/unlocking arrangement and 100 mm thick R.C.C (1:2:4) top slab, including
centering, shuttering, fabricating, casting and curing etc. complete up to required
depth including necessary earth work in excavation and shoring, bailing out water
and side filling including the cost of all materials, operations and incidental charges. 1.00 Nos Tk. 200,000.00 Tk. 200,000.00
etc. all complete as per type plan approved and accepted by the Engineer. (Rate is
including cost of reinforcement and its fabrication, binding and placing)
For 100 users of each septic tank.

24 Construction of soak well of different sizes (medium and large sizes) with 250 mm
thick solid brick work and 250 mm honey comb brick work with cement mortar (1:6)
as per design over R.C.C. (1:2:4) well curb with 1% reinforcement up to the depth as
per drawing with 450 mm dia water sealed heavy type. C.I. manhole cover with
locking arrangement, filling the well up to the required depth with graded khoa and
sand including supplying and fabricating M.S. Rod, casting, curing including
necessary earth work in excavation, side filling and bailing out water including cost
of all materials etc. all complete as per drawing, design approved and accepted by 1.00 Nos Tk. 320,000.00 Tk. 320,000.00
the Engineer. (Rate is including cost of reinforcement and its fabrication, binding and
placing) For 100 users of each soak well .

Sub total of Part C Tk. 2,632,850.00

SL Description of item QTY UNIT RATE AMOUNT
PART D- SUBSTATION & GENARATOR
11kV LIGHTNING ARRESTER : Cost of complete 11KV Lightning Arrester as per
1.1 attached technical specification. 1.00 Set Tk. 6,250.00 Tk. 6,250.00

11KV DROP - OUT FUSE : Cost of complete 11KV Drop-out fuse as per attached
1.2 technical specification. 1.00 Set Tk. 5,000.00 Tk. 5,000.00

11KV HT SWITCHGEAR (630A LBS) : Cost of complete HTSwitchgear as per attached

1.3 technical specification. 1.00 NO. Tk. 150,000.00 Tk. 150,000.00

315kVA Oil Type transformer : Cost of complete 315kVA X-Former as per attached
1.4 technical specification. 1.00 NO. Tk. 618,750.00 Tk. 618,750.00

LT Switchgear : Cost of complete LT Switchger as per attached technical specification.

1.5 1.00 Set Tk. 183,240.80 Tk. 183,240.80

190 kVAR AUTO/MANUAL PFI PLANT : Cost of complete 190 kVAR PFI Plant as per
1.6 attached technical specification. 1.00 Set Tk. 201,759.20 Tk. 201,759.20

1.7 Earthing & Heat Shrinkable Kit: 4.00 Sets Tk. 27,500.00 Tk. 110,000.00
1.8 ELB (Without Govt. Fees) 1.00 Job Tk. 40,000.00 Tk. 40,000.00
1.9
Delivery, Installation & Testing : Cost of installation & testing of the above without
1.1 any cable & civil works. 1.00 Job Tk. 35,000.00 Tk. 35,000.00

2 Generator
2.1 300 KVA (Prime) Rating Diesel Generator with engine and alternator 1.00 Set Tk. 3,500,000.00 Tk. 3,500,000.00
2.2 Local Canopy for 300 KVA Genset 1.00 pcs Tk. 355,000.00 Tk. 355,000.00
2.3 Local Auto Transfer Switch (ATS) for 300 KVA Genset 1.00 pcs Tk. 195,000.00 Tk. 195,000.00
Sub total of Part D Tk. 5,400,000.00
SL Description of item QTY UNIT RATE AMOUNT
PART E- INTERNAL ELECTICAL WORKS
1 Lighting
CCT: 6500K, CRI: 80-83, IP: 20
Life Time: 15,000-50,000 hours (higher life time is recommended)
Beam Angle: 120-160 Degree Standard: IEC Depriciation Per Year: 2-
3% (less is best) Included short circuit protection fuse device
 SL Description of item QTY UNIT RATE AMOUNT
LED Panel Light
Size: 2 Feet X 2 Feet
Power: 32W
1.1 Total Lumen: 3000Lm 170.00 Nos Tk. 4,000.00 Tk. 680,000.00
Lumen Per Watt: 94

LED Ceiling Light

Size: Round
Power: 9W
1.2 Total Lumen: 800Lm 200.00 Nos Tk. 1,750.00 Tk. 350,000.00
Lumen Per Watt: 80

2 Socket and Switch

All socket and switchboard should be full fill the following requirements-Fire
retardand, Moisture resistance, Number of switching on/off: 35,000-40,000 times,
Contact:Pure copper with silver tip, Plug insertion and withdrawl: 30,000 cycles per
socket, Standard:IEC/BDS/BS

2.1 2 Pin socket Size: MK Ampere

Rating: 5 Amp Voltage Rating: 230 Volt 80.00 Nos Tk. 300.00 Tk. 24,000.00

2.2 3 Pin socket Size: MK Ampere

Rating: 13 Amp Voltage Rating: 230 Volt 130.00 Nos Tk. 550.00 Tk. 71,500.00

2.3 Switch Board Size: MK Ampere

Rating: 5 Amp Voltage Rating: 230 Volt 100.00 Nos Tk. 655.00 Tk. 65,500.00

2.4 Internet socket Wall Data Socket serves as the work area endpoints for horizontal
cable runs 70.00 Nos Tk. 490.00 Tk. 34,300.00

2.5 Telephone socket: Anti-corrosive & Anti rust metal, Copper Connecting Plate, Fire
retardant, Highly Resistant to Moisture, Heat & Fire, Applicable for AC & DC, 70.00 Nos Tk. 275.00 Tk. 19,250.00
Ensures sparking free contact

2.6 Intercom socket 70.00 Nos Tk. 275.00 Tk. 19,250.00

3.0 Electrical Panel Board:
Supply and fixing of wall mounted AC DB made of 18 SWG GP Sheet board of duly
painted with powder coating with epoxy polyester resin on all surfaces having built
in push type locking arrangement including metal bridges/plug system of suitable
size for fixing TP MCB/TP MCCB's incoming and outgoing and copper busbar, neutral
& earth links and interconnection wires set complete with suitable anchoring
arrangement and keeping provision for cable in exit as required.

3.1 SDB for GF, 1F, 2F 3.00 set Tk. 35,000.00 Tk. 105,000.00
3.2 SDB for 1BF, 2BF 2.00 set Tk. 15,000.00 Tk. 30,000.00
3.3 TJB, IJB and Intercom JB 3.00 set Tk. 31,500.00 Tk. 94,500.00
4.0 Cables
Cables shall be manufactured and tested according to relevant IEC/BDS/BS/VDE
standards and as per detailed specification mentioned in Annexure-A.

4.1 1Cx1.5 sq. mm BYA Cu cable

4.1.1 Phase (L) cable (brown) 4000.00 rm Tk. 16.34 Tk. 65,360.00
4.1.2 Neutral (N) cable (blue) 4000.00 rm Tk. 16.34 Tk. 65,360.00

4.2 1Cx2.5 sq. mm BYA Cu cable

4.2.1 Phase (L) cable (brown) 5600.00 rm Tk. 26.05 Tk. 145,880.00
4.2.2 Neutral (N) cable (blue) 5600.00 rm Tk. 26.05 Tk. 145,880.00
4.2.3 ECC cable 4sq. mm BYA (green-yellow) 5700.00 rm Tk. 40.56 Tk. 231,192.00

4.3 1Cx4 sq. mm BYA Cu cable

4.3.1 Line1 (L1)/3phase cable (brown) 100.00 rm Tk. 40.56 Tk. 4,056.00
4.3.2 Line2 (L2)/3phase cable (black) 100.00 rm Tk. 40.56 Tk. 4,056.00
4.3.3 Line3 (L3)/3phase cable (grey) 100.00 rm Tk. 40.56 Tk. 4,056.00
4.3.4 Neutral (N) cable (blue) 100.00 rm Tk. 40.56 Tk. 4,056.00

4.4 1Cx10 sq. mm 2XY (XLPE) Cu cable

4.4.1 Line1 (L1)/3phase cable (brown) 150.00 rm Tk. 115.00 Tk. 17,250.00
4.4.2 Line2 (L2)/3phase cable (black) 150.00 rm Tk. 115.00 Tk. 17,250.00
4.4.3 Line3 (L3)/3phase cable (grey) 150.00 rm Tk. 115.00 Tk. 17,250.00
4.4.4 Neutral (N) cable (blue) 150.00 rm Tk. 115.00 Tk. 17,250.00
4.4.5 ECC cable 10sq. mm BYA (green-yellow) 150.00 rm Tk. 99.70 Tk. 14,955.00

4.5 1Cx35 sq. mm 2XY (XLPE) Cu cable

4.5.1 Line1 (L1)/3phase cable (brown) 150.00 rm Tk. 370.18 Tk. 55,527.00
 SL Description of item QTY UNIT RATE AMOUNT
4.5.2 Line2 (L2)/3phase cable (black) 150.00 rm Tk. 370.18 Tk. 55,527.00
4.5.3 Line3 (L3)/3phase cable (grey) 150.00 rm Tk. 370.18 Tk. 55,527.00
4.5.4 Neutral (N) cable (blue) 150.00 rm Tk. 370.18 Tk. 55,527.00
4.5.5 ECC cable 16sq. mm BYA (green-yellow) 150.00 rm Tk. 158.03 Tk. 23,704.50

4.6 1Cx50 sq. mm 2XY (XLPE) Cu cable

4.6.1 Line1 (L1)/3phase cable (brown) 20.00 rm Tk. 521.87 Tk. 10,437.40
4.6.2 Line2 (L2)/3phase cable (black) 20.00 rm Tk. 521.87 Tk. 10,437.40
4.6.3 Line3 (L3)/3phase cable (grey) 20.00 rm Tk. 521.87 Tk. 10,437.40
4.6.4 ECC cable 50sq. mm BYA (green-yellow) 10.00 rm Tk. 486.52 Tk. 4,865.20

4.7 1Cx95 sq. mm 2XY (XLPE) Cu cable

4.7.1 Line1 (L1)/3phase cable (brown) 70.00 rm Tk. 965.55 Tk. 67,588.50
4.7.2 Line2 (L2)/3phase cable (black) 70.00 rm Tk. 965.55 Tk. 67,588.50
4.7.3 Line3 (L3)/3phase cable (grey) 70.00 rm Tk. 965.55 Tk. 67,588.50
4.7.4 Neutral (N) cable (blue) 70.00 rm Tk. 913.03 Tk. 63,912.10
4.7.5 ECC cable 95sq. mm BYA (green-yellow) 25.00 rm Tk. 913.03 Tk. 22,825.75

4.8 3Cx70 sq. mm XLPE HT Cu cable 40.00 rm Tk. 4,328.15 Tk. 173,126.00

4.9 Communication cable

4.9.1 CAD6 internet cable 1800.00 rm Tk. 35.00 Tk. 63,000.00
4.9.2 2 Pair Telephone cable 3600.00 rm Tk. 18.00 Tk. 64,800.00

5.0 CC Camera system

5.1 DVR 32 channels 3.00 pcs Tk. 80,597.00 Tk. 241,791.00
5.2 DVR 24 channels 1.00 pcs Tk. 74,681.00 Tk. 74,681.00
5.3 CC Camera 130.00 pcs Tk. 11,094.00 Tk. 1,442,220.00
Sub total of part E Tk. 4,878,262.25
SL Description of item QTY UNIT RATE AMOUNT
PART F- HVAC
Variable Refrigerant Flow/Volume (VRF/VRV) System with Fan Coil Unit
1.0
VRF/VRV Condensing Units
Brand :
Country of Origin:
Country of Assemble:
Variable Refrigerant Flow (VRF) units having cooling capacities as mentioned below.
Each unit shall be Modular Type complete with Inverter type Compressor, DX
Condenser with Copper tube and Aluminum Fins. Condenser Fan with Fan guard,
complete in all respect.The unit shall operate when supplied with 400±10% v/50
hz/3 ph Electric power.

The supply includes all accessories to complete VRF Mechanism including voltage
free contact for connection with BMS system. 9.00 sets Tk. 650,000.00 Tk. 5,850,000.00

Condenser air inlet temperature: 35 deg C

Evaporator Air inlet temperature 27° C DB/19.5° C WB
Refrigerant : R410A, Factory Charged
COP: 4.0 (Minimum)
Compressor type: DC Inverter scroll Type
Single Outdoor Unit capacity: 17.50- 18.00 TR/210000-215000 BTU/H

2.0 VRF Fan Coil Unit (Indoor Unit)

Brand :
Country of Origin:
Country of Assemble:
Fan Coil units having cooling capacities as mentioned below. Each unit shall be
operated with Variable Refrigerant Flow (VRF/VRV) outdoor units. FCU shall have
Electronic refrigerant control valve (EXV), washable filter, fan speed controller,
Terminal Box, Voltage Transformer, etc. complete in all respect. Vent port shall be
built in inside the unit. The unit shall operate when supplied with
220±10% V / 50hz / 1 Ph Electric power.

All FCUs shall have built in or additional Drain Pump.

 SL Description of item QTY UNIT RATE AMOUNT
Air entering to cooling coil: 27 C DB / 19 C WB
Type: DX Ducted ceiling hide away type
Accessories:
Wall mounted Networking Thermostat,
Remote Controller
2.1 4-Way Cassette Type Fan Coil Unit with Wireless Remote:
2.1.1 Cooling capacity : 2.00 TR (7.1 kw) 24.00 sets Tk. 65,000.00 Tk. 1,560,000.00
2.1.2 Cooling capacity : 4.00 TR (14.1 kw) 27.00 sets Tk. 80,000.00 Tk. 2,160,000.00
3.0 RefNet Joints:
Brand :
Country of Origin:
Country of Assemble:
Supply and fixing of RefNet made of pure copper with insulation pressure tolerance
not less 450 psi Copper thickness should be 2 mm. Y shaped RefNet joint as per
requirement. 48.00 sets Tk. 12,000.00 Tk. 576,000.00

4.0 Refrigerant Pipe & Accessories

Refrigerant Piping shall be medium grade (L) Copper piping with long bend, support,
hangers, other accessories.Pipe shall be c/w Nitrile rubber insulation of min
12.0mm thickness.

4.1 Size: Ø 9.5mm 237.80 rm Tk. 393.60 Tk. 93,598.08

4.2 Size: Ø 12.7mm 60.98 rm Tk. 492.00 Tk. 30,002.16
4.3 Size: Ø 15.9mm 259.15 rm Tk. 590.40 Tk. 153,002.16
4.4 Size: Ø 19.1mm 146.34 rm Tk. 852.80 Tk. 124,798.75
4.5 Size: Ø 22.2mm 30.49 rm Tk. 1,033.20 Tk. 31,502.27
4.6 Size: Ø 28.58 mm 106.71 rm Tk. 1,344.80 Tk. 143,503.61
4.7 Size: Ø 34.9mm 30.49 rm Tk. 1,968.00 Tk. 60,004.32
4.8 Size: Ø 41.3mm 121.95 rm Tk. 2,050.00 Tk. 249,997.50
5.0 Condensate Drain Pipe:
Water grade uPVC Pipe of the following sizes including Supply, Installation of
consumables hangers, unions other consumables etc. compleate in all respects. Pipe
work shall be properly plumbed, leveled and fix. The pipe shall be insulated with at
least 12mm thick polystyrene/Nitrile Rubber/ PU insulation with Aluminum Foil
pasted

5.1 pipe dia 25mm 457.32 rm Tk. 295.20 Tk. 135,000.86

5.2 pipe dia 32mm 152.44 rm Tk. 360.80 Tk. 55,000.35
6.0 Communication Control Wiring:
communication cable from Outdoor to Indoor unit. all complete as per direction as
per following size. 762.20 rm Tk. 264.00 Tk. 201,220.80
2C-0.75 mm² Cable
7.0 Additional Charging of Refrigerant R410A 100.00 Kg Tk. 1,200.00 Tk. 120,000.00
8.0 Ventillation Fan for Basement Floor:
8.1 Capacity: 6000 CFM 2.00 sets Tk. 160,000.00 Tk. 320,000.00
8.2 Capacity: 7000 CFM 2.00 sets Tk. 180,000.00 Tk. 360,000.00
Ducting Works for Basement:
9.0 Sheet Metal Ducting:
Duct works include Tees, bends, elbows, reducers, offsets, Air terminal necks, etc.
with prime quality sheet. The ducts shall be complete with necessary angle, flange
bracing. Stiffeners, Hanger, Supports, Brackets, etc. made of M.S. Angle / Flat bar.
Approved sealant shall have to be used to make duct leak proof. Before installation
duct inside shall be cleaned. All hangers shall have to be painted with red oxide
paint. ASHRAE & SMACNA standards shall have to be followed for construction.

9.1 Duct made of 24 SWG 511.23 sqm Tk. 2,044.10 Tk. 1,045,005.24
9.2 Duct made of 22 SWG 371.80 sqm Tk. 2,151.68 Tk. 799,994.62
10.0 Air Terminals
Air terminals shall be constructed with extruded aluminum with powder coating
finishing. Thickness shall be not less than 18 SWG.
10.1 Supply Air & Return Grille:
10.1.1 Neck Size: 30" x 10" 14.00 Nos Tk. 4,000.00 Tk. 56,000.00
10.1.2 Neck Size: 48" x 10" 10.00 Nos Tk. 5,500.00 Tk. 55,000.00
10.2 Fresh Air Louver c/w G4 washable filter:
10.2.1 Neck Size: 48"x 30" 2.00 sets Tk. 14,000.00 Tk. 28,000.00
 SL Description of item QTY UNIT RATE AMOUNT
10.2.2 Neck Size: 54"x 30" 2.00 sets Tk. 15,000.00 Tk. 30,000.00
11.0 Duct Flexible Joint 8.00 Nos Tk. 2,000.00 Tk. 16,000.00
Connecting between Duct & Fresh air unit by Proper canvas cloth with associate
items
12.0 Electrical Cable work:
Supply and fixing of electrical cable including all consumable accessories for laying
the cable as per standard rulse and regulation of electrical work. Cable work shall be
AC DB starter panel to machines.

Cable: P3 x 10 rm NYY + N1 x 10 rm NYY + E1 x 10 rm BYA 820.00 rm Tk. 2,296.00 Tk. 1,882,720.00

Cable: P1 x 1.5 rm BYA + N1 x 1.5 rm BYA + E1 x 1.5 rm BYA 7872.00 rm Tk. 278.80 Tk. 2,194,713.60
13.0 Electrical Panel Board:
Supply and fixing of wall mounted AC DB made of 18 SWG GP Sheet board of duly
painted with powder coating with epoxy polyester resin on all surfaces having built
in push type locking arrangement including metal bridges/plug system of suitable
size for fixing TP MCB/TP MCCB's incoming and outgoing and copper busbar, neutral
& earth links and interconnection wires set complete with suitable anchoring
arrangement and keeping provision for cable in exit as required.

13.1 For VRF Outdoor & Indoor Unit: 3.00 set Tk. 55,000.00 Tk. 165,000.00
13.2 Basement Ventilation 2.00 set Tk. 32,000.00 Tk. 64,000.00
14.0 Shop drawing and Documentation 1.00 job Tk. 50,000.00 Tk. 50,000.00
Preparation of detail Shop drawing including, layout drawing, section details,
schematic drawing, etc. Get approval of shop drawing before any fabrication or
installation works. Shop drawing must be coordinated with other services likely
Electrical cabling, Light fixtures, False Ceiling and Interior design. The work also
includes:

a). Show actual dimension of Equipment.

b). Submit actual KW rating of all equipment
c). Reconfirm Electrical cable sizing
d). Reconfirm Ampere ratings of AC Panel's components
e). Submit Electrical connection diagram of AC Panels
f). Submit General arrangement of AC panels
g). Submit Plinth drawing for Equipment
h). Submit Electrical and P & I Diagram of VRF & PAC AC units
i). Submit advance copy of Installation, Operation and Maintenance manuals of
Equipments.
Contractor should prepare this drawing at site coordinating with other
15.0 Testing, Commissioning and Balancing 1.00 job Tk. 100,000.00 Tk. 100,000.00
After proper installation and certification the system shall be tested, commissioned
and balanced as per direction and recommendation by the manufacturer as well as
HVAC Designer. Contractor shall do (but not limited to) following works under this
clause.

a). Prepare and submit Commissioning protocol and get approval from Consultant.

b). Carry out duct inspection

c). Carry out pipe pressure testing
d). Carry our Electrical Cabling testing
e). Testing of condensate water drainage slope with water
f). Testing of AC Units
g). Air Balancing
h). Commissioning of Automatic Control system
All testing and commissioning works must be documented in approved formats. All
of these documents must be jointly witnessed and signed by the Client and
Contractor's authorized Engineer.

Sub total of part F Tk. 18,710,064.33

SL Description of item QTY UNIT RATE AMOUNT
PART G- FIRE DETECTION & FIRE PROTECTION SYSTEM
1 Fire Alarm Control Panel 1.00 Set Tk. 301,862.00 Tk. 301,862.00
Microprossor based Fire Alarm Control Panel (Addressabile) shall be capable to
handle at least 232 detectors per loop.
The FACP shall provide the following features
a. Network option - over 100 nodes supported.
b. Built-in Alarm, Trouble, security and Supervisory relays.
c. Printer interface.
d. History File.
SL Description of item QTY UNIT RATE AMOUNT
e. Alarm Verification selection per point with tally.
f. Silence inhibit and Auto Silence timer options.
g.Emergency warning & intercommunication system
h.Fire fighting pump.
i. Lifts
j. Alarm Valves
k. BMS Gateway
UL Listed, LPCB & FM Approved
2 Manual Call Point 15.00 Sets Tk. 4,500.00 Tk. 67,500.00
Supply of Addressable type manual call point like break glass switch or single action
pull station complete with back box and all other accessories and consumables.
Power supply shall be 24V DC. UL Listed, LPCB & FM Approveded .

3 Strobe with Horn 25.00 Sets Tk. 3,000.00 Tk. 75,000.00

Addressable type Horn with Strobe for Audible & Visible application, combination of
Audible & Visible (A/V) Notification Appliances shall be listed to UL 1971 and UL
464. The strobe light shall consist of a xenon flash tube and associated lens /
reflector system.

Provide a label inside the strobe lens to indicate the listed candela rating of the
specific strobe. The horn shall have a minimum sound pressure level of 83 to 89 DBA
@ 24VCD. The audible / visible enclosure shall mount directly to standard single
gang, double gang or 4” square electrical box, without the use of special adapters or
trim rings. Shall be suitable to temperature range: 0º to 50º C

UL Listed, LPCB & FM Approved

4 Multi detector 5.00 Sets Tk. 3,800.00 Tk. 19,000.00
Intelligent addressable Microprocessor based Multisensor detector with mounting
base, LED, address switch to programme the detectors complete as required. UL
Listed, LPCB & FM Approved

5 Smoke Detector 50.00 Sets Tk. 2,950.00 Tk. 147,500.00

Microprocessor based addressable Smoke Detector. Detector sensitivity must be
programmed in the control panel software. Sensitivity must be continuously
monitored and reported to the panel. UL Listed, LPCB & FM Approved

6 Heat Detector 5.00 pcs Tk. 2,950.00 Tk. 14,750.00

Microprocessor based addressable Fixed temperature rate of rise thermal detector.
It shall have electronic dual thermistor and a fixed alarm temperature of 60 deg C.
The unit shall have LED indicator. UL Listed, LPCB & FM Approved

8 Fault Isolator Module 8.00 Sets Tk. 3,000.00 Tk. 24,000.00

Supply & installation of fault isolator module is used to protect the system against
wire-to-wire short circuits on the loop. The modules shall be spaced between
groups of sensors or modules in a loop to protect the rest of the loop. In the event
of a short circuit between any two fault isolator modules, both modules
immediately switch to an open circuit condition and isolate any group of sensors
between them. The remaining units on the circuit will continue to operate in a
normal fashion ( must be wired in class 'A' or Style 6) A maximum load of 25 devices
can be connected to an isolator to insure that the isolator powers up correctly. UL
Listed, LPCB & FM Approved

11 Emergency Light 5.00 Sets Tk. 5,000.00 Tk. 25,000.00

Double tube, Length 12", Ceiling mounted.
15 Electrical Cabling Work
PVC insulated PVC sheathed copper conductor single / multicore cable complete
with PVC conduit, Tray / Ladder and copper conductor (ECC). Conduit works shall be
complete with Bends, Tees, Junction box, etc. The others details shall be as per
Technical Specifications and drawing.

2x1C-1.5mm2(FR) With 1.5mm2(FR) Through PVC Conduit 1200.00 rm Tk. 100.00 Tk. 120,000.00
2x1C-2.5mm2(FR) With 1.5mm2(FR) Through PVC Conduit(Sounder & Bell ) 800.00 rm Tk. 120.00 Tk. 96,000.00
16 Shop drawing and Documentation 1.00 Job Tk. 25,000.00 Tk. 25,000.00
Preparation of detail Shop drawing including, layout drawing, section details,
schematic drawing, etc. Get approval of shop drawing before any fabrication or
installation works. Shop drawing must be coordinated with other services likely
Electrical cabling, Light Fixtures, False Ceiling and Interior design. The work also
includes:

a)Show actual dimension of Equipment.

SL Description of item QTY UNIT RATE AMOUNT
b) Submit advance copy of Installation, Operation and maintenance manuals.
Tagging and identification of all items as per recommendation of the Consultant.

18 Installation, Testing, Commissioning and Balancing 1.00 Job Tk. 150,000.00 Tk. 150,000.00
After proper installation and certification the system shall be tested, commissioned
and balanced as per direction and recommendation by the Manufacturer as well as
Designer.

Sub total of part G Tk. 1,065,612.00

DRAFT ABSTRACT: TENTATIVE COST ESTIMATE of POTENTIAL 03 STORIED OFFICE BUILDING WITH 02
DHAKA, BANGLADESH.

SL DESCRIPTION
1.0 PART A- CIVIL
2.0 PART B- EXTERNAL AND INTERNAL FINISHING WORK
PART C- INTRENAL PLUMBING (WATER SUPPLY &
3.0 SANITARY) SYSTEM
4.0 PART D- SUBSTATION & GENARATOR
5.0 PART E- INTERNAL ELECTICAL WORKS
6.0 PART F- HVAC
7.0 PART G- FIRE DETECTION & FIRE PROTECTION SYSTEM
TOTAL AMOUNT
AL 03 STORIED OFFICE BUILDING WITH 02 BASEMENT OF IFC, SHER-E-BANGLA NAGAR
DHAKA, BANGLADESH.

AMOUNT ( IN BDT) AMOUNT (IN USD)

Tk. 104,297,363.95 $1,232,392.34
Tk. 37,125,021.77 $438,674.49

Tk. 2,632,850.00 $31,110.13

Tk. 5,400,000.00 $63,807.16

Tk. 4,878,262.25 $57,642.23
Tk. 18,710,064.33 $221,080.76
Tk. 1,065,612.00 $12,591.42
Tk. 174,109,174.29 $2,057,298.53
Tk. 17.03 Crore USD 2.01 million

NOTE:
CURRENCY CONVERSION RATE IS 1 DOLLAR = Tk. 84.63 AS ON AUGUST 06, 2018