Scribd
Upload
49 views

Motors

A dynamo is an electrical generator that uses a commutator to create direct current. Dynamos were the first generators capable of powering industry and were the basis for later devices like motors and alternators. Today, alternators are more commonly used for large-scale power generation due to greater efficiency and lower costs. A dynamo requires a commutator to produce DC, which reverses the polarity of the induced current, while alternators produce AC without a commutator.

Uploaded by

Richard
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
49 views

Motors

A dynamo is an electrical generator that uses a commutator to create direct current. Dynamos were the first generators capable of powering industry and were the basis for later devices like motors and alternators. Today, alternators are more commonly used for large-scale power generation due to greater efficiency and lower costs. A dynamo requires a commutator to produce DC, which reverses the polarity of the induced current, while alternators produce AC without a commutator.

Uploaded by

Richard
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

DYNAMOTOR (DYNAMO)

A dynamo is an electrical generator that creates direct current using a commutator.


Dynamos were the first electrical generators capable of delivering power for industry, and the
foundation upon which many other later electric-power conversion devices were based, including
the electric motor, the alternating-current alternator, and the rotary converter. Today, the simpler
alternator dominates large scale power generation, for efficiency, reliability and cost reasons. A
dynamo has the disadvantages of a mechanical commutator. Also, converting alternating to direct
current using power rectification devices (vacuum tube or more recently solid state) is effective
and usually economical.

The original "dynamo principle" of Wehrner von Siemens or Werner von Siemens referred
only the direct current generators which use exclusively the self-excitation (self-induction)
principle to generate DC power. The earlier DC generators which used permanent magnets were
not considered "dynamo electric machines". The invention of the dynamo principle (self-induction)
was a huge technological leap over the old traditional permanent magnet based DC generators.
The discovery of the dynamo principle made industrial scale electric power generation technically
and economically feasible. After the invention of the alternator and that alternating current can be
used as a power supply, the word dynamo became associated exclusively with
the commutated direct current electric generator, while an AC electrical generator using
either slip rings or rotor magnets would become known as an alternator.

Commutation
The commutator is needed to produce direct current. When a loop of wire rotates in a magnetic
field, the magnetic flux through it, and thus the potential induced in it, reverses with each half turn,
generating an alternating current. However, in the early days of electric
experimentation, alternating current generally had no known use. The few uses for electricity,
such as electroplating, used direct current provided by messy liquid batteries. Dynamos were
invented as a replacement for batteries. The commutator is essentially a rotary switch. It consists
of a set of contacts mounted on the machine's shaft, combined with graphite-block stationary
contacts, called "brushes", because the earliest such fixed contacts were metal brushes. The
commutator reverses the connection of the windings to the external circuit when the potential
reverses, so instead of alternating current, a pulsing direct current is produced.

Excitation
The earliest dynamos used permanent magnets to create the magnetic field. These were referred
to as "magneto-electric machines" or magnetos. However, researchers found that stronger
magnetic fields, and so more power, could be produced by using electromagnets (field coils) on
the stator. These were called "dynamo-electric machines" or dynamos. The field coils of the stator
were originally separately excited by a separate, smaller, dynamo or magneto. An important
development by Wilde and Siemens was the discovery (by 1866) that a dynamo could
also bootstrap itself to be self-excited, using current generated by the dynamo itself. This allowed
the growth of a much more powerful field, thus far greater output power.

Electrical Power Generation


Dynamos, usually driven by steam engines, were widely used in power stations to generate
electricity for industrial and domestic purposes. They have since been replaced by alternators.
Large industrial dynamos with series and parallel (shunt) windings can be difficult to use
together in a power plant, unless either the rotor or field wiring or the mechanical drive systems
are coupled together in certain special combinations. It seems theoretically possible to run
dynamos in parallel to create induction and self sustaining system for electrical power.
ROTARY CONVERTERS
After dynamos and motors were found to allow easy conversion back and forth between
mechanical or electrical power, they were combined in devices called rotary converters, rotating
machines whose purpose was not to provide mechanical power to loads but to convert one type
of electric current into another, for example DC into AC. They were multi-field single-rotor devices
with two or more sets of rotating contacts (either commutators or sliprings, as required), one to
provide power to one set of armature windings to turn the device, and one or more attached to
other windings to produce the output current.
The rotary converter can directly convert, internally, any type of electric power into any
other. This includes converting between direct current (DC) and alternating current (AC), three
phase and single phase power, 25 Hz AC and 60 Hz AC, or many different output voltages at the
same time. The size and mass of the rotor was made large so that the rotor would act as
a flywheel to help smooth out any sudden surges or dropouts in the applied power.
The technology of rotary converters was replaced in the early 20th century by mercury-
vapor rectifiers, which were smaller, did not produce vibration and noise, and required less
maintenance. The same conversion tasks are now performed by solid state power semiconductor
devices. Rotary converters remained in use in the West Side IRT subway in Manhattan into the
late 1960s, and possibly some years later. They were powered by 25 Hz AC, and provided DC at
600 volts for the trains.

You might also like