Release Notes for

Cisco Configuration Professional 2.0

October 20, 2009

These release notes support Cisco Configuration Professional (Cisco CP) version 2.0. They should be
used with the documents listed in the “Related Documentation” section.
These release notes are updated as needed. To ensure that you have the latest version of these release
notes, go to http://www.cisco.com/go/ciscocp. In the Support box, click General Information >
Release Notes, and then find the latest release notes for your release.

Contents
This document contains the following sections:
• Introduction
• System Requirements
• New and Changed Information
• Limitations and Restrictions
• Important Notes
• Caveats
• Related Documentation

Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
© 2009 Cisco Systems, Inc. All rights reserved.
 Introduction

Introduction
Cisco CP is a GUI-based device management tool for Cisco access routers. Cisco CP simplifies router,
firewall, IPS, VPN, unified communications, WAN, and basic LAN configuration through GUI-based,
easy-to-use wizards. Cisco CP is installed on a PC.
Routers that are ordered with Cisco CP are shipped with Cisco Configuration Professional Express
(Cisco CP Express) installed in router flash memory. Cisco CP Express is a light weight version of Cisco
CP, that you can use to configure LAN and WAN interfaces and minimal IOS security features.

System Requirements
This sections describes PC and router system requirements. It contains the following parts:
• PC System Requirements
• Router System Requirements
• Cisco CP Ordering Options

PC System Requirements
Table 1 lists the system requirements for a PC running Cisco CP. Although the Cisco CP application
requires JRE to run, the Cisco CP Express application included with Cisco CP can run under the native
Java Virtual Machine in the supported browsers, and also JRE.

Table 1 PC System Requirements

System Component Requirement

Processor 2 GHz processor or faster
Random Access Memory 1 GB
Hard disk available memory 400 MB
Operating System Any of the following:
• Microsoft Windows Vista Business Edition
• Microsoft Windows Vista Ultimate Edition
• Microsoft Windows XP with Service Pack 2 or later
• Mac OSX 10.5.6 running Windows XP using VMWare 2.0
Browser Internet Explorer 6.0 or above
Screen Resolution 1024 X 768
Java Runtime Environment JRE versions minimum 1.5.0_11 upto 1.6.0_16 are supported.
Adobe Flash Player Version 10.0 or later, with Debug set to No
Secure Shell (SSH) Required for secure connections with the router.
Versions up to 1.99 are supported.

Release Notes for Cisco Configuration Professional 2.0

2 OL-20446-01
 System Requirements

Router System Requirements

Router System Requirements are described in the following parts:
• Supported Routers
• Supported Phones
• Supported Network Modules
• Supported Interface Cards
• Supported Adapters, Processing Engines, and Service Engines
• Cisco IOS Releases
• Required IP Address Configuration Information
• Router Configuration Requirements

Supported Routers
Table 2 and Table 3 list the routers that Cisco CP supports.
.
Table 2 Supported Integrated Services Routers (ISR)

Cisco 800 Series Cisco 1800 Series Cisco 2800 Series Cisco 3800 Series Cisco 7000 Series
CISCO815 CISCO1801 Cisco 2801 Cisco 3825 Cisco 7204VXR
CISCO815-VPN-K9 CISCO1801-M Cisco 2811 Cisco 3825-NOVPN Cisco 7206VXR
CISCO1801/K9 Cisco 2821 Cisco 3845 Cisco 7301
CISCO1801-M/K9 Cisco 2851 Cisco 3845-NOVPN
CISCO1801WM-AGE/K9
CISCO1801W-AG-E/K9
CISCO1801W-AG-B/K9
CISCO1801W-AG-C/K9
CISCO1801W-AG-N/K9
CISCO851-K9 CISCO1802
CISCO851W-G-A-K9 CISCO1802/K9
CISCO851W-G-E-K9 CISCO1802W-AG-E/K9
CISCO851W-G-J-K9
CISCO857-K9 CISCO1803/K9
CISCO857W-G-A-K9 CISCO1803W-AG-B/K9
CISCO857W-G-E-K9 CISCO1803W-AG-E/K9

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 3
 System Requirements

Table 2 Supported Integrated Services Routers (ISR) (continued)

Cisco 800 Series Cisco 1800 Series Cisco 2800 Series Cisco 3800 Series Cisco 7000 Series
CISCO871-K9 CISCO1805-D
CISCO871-SEC-K9 CISCO 1805-D/K9
CISCO871W-G-A-K9 CISCO1811/K9
CISCO871W-G-E-K9 CISCO1811W-AG-B/K9
CISCO871W-G-J-K9 CISCO1811W-AG-C/K9
CISCO1811W-AG-N/K9
CISCO876-K9 CISCO1812/K9
CISCO876-SEC-K9 CISCO1812 W-AG-E/K9
CISCO876-SEC-I-K9 CISCO1812 W-AG-C/K9
CISCO876W-G-E-K9
CISCO877-K9 CISCO1841
CISCO877-M-K9
CISCO877-SEC-K9
CISCO877W-G-A-K9
CISCO877W-G-E-K9
CISCO877W-G-E-M-K9
CISCO878-K9 C1861-UC-4FXO-K9
CISCO878-SEC-K9 C1861-UC-2BRI-K9
CISCO878W-G-A-K9 C1861-SRST-B/K9
CISCO878W-G-E-K9 C1861-SRST-C-B/K9
C1861-SRST-C-F/K9
C1861-SRST-F/K9

Release Notes for Cisco Configuration Professional 2.0

4 OL-20446-01
 System Requirements

Table 3 Supported Integrated Services Routers - G2 (ISR- G2)

Cisco 800 Series Cisco 1900 Series Cisco 2900 Series Cisco 3900 Series
CISCO861-K9 CISCO1941/K9 CISCO2901/K9 CISCO3925/K9
CISCO861W-GN-A-K9 CISCO1941W-A/K9 CISCO2911/K9 CISCO3945/K9
CISCO861W-GN-E-K9 CISCO1941W-E/K9 CISCO2921/K9
CISCO861W-GN-P-K9 CISCO1941W-P/K9 CISCO2951/K9
CISCO867-W-GN-A-K9 CISCO1941W-N/K9
CISCO867-W-GN-E-K9
CISCO881-K9
CISCO881W-GN-A-K9
CISCO881W-GN-E-K9
CISCO881W-GN-P-K9
CISCO881G-K9
CISCO881GW-GN-A-K9
CISCO881GW-GN-E-K9
CISCO881G-S-K9
CISCO881G-V-K9
CISCO881G-A-K9
CISCO881SRST-K9
CISCO881SRSTW-GN-A-K9
CISCO881SRSTW-GN-E-K9
CISCO886-K9
CISCO886W-GN-E-K9
CISCO886G-K9
CISCO886GW-GN-E-K9
CISCO887-K9
CISCO887W-GN-A-K9
CISCO887W-GN-E-K9
CISCO887M-K9
CISCO887MW-GN-E-K9
CISCO887G-K9
CISCO887GW-GN-A-K9
CISCO887GW-GN-E-K9

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 5
 System Requirements

Table 3 Supported Integrated Services Routers - G2 (ISR- G2)

Cisco 800 Series Cisco 1900 Series Cisco 2900 Series Cisco 3900 Series
CISCO888-K9
CISCO888W-GN-A-K9
CISCO888W-GN-E-K9
CISCO888G-K9
CISCO888GW-G-AN-K9
CISCO888GW-G-EN-K9
CISCO888SRST-K9
CISCO888SRSTW-GN-A-K9
CISCO888SRSTW-GN-E-K9
CISCO891-K9
CISCO891W-AGN-A-K9
CISCO891W-AGN-N-K9
CISCO892-K9
CISCO892W-AGN-E-K9

Release Notes for Cisco Configuration Professional 2.0

6 OL-20446-01
 System Requirements

Supported Phones
Table 4 lists the phones that Cisco CP supports:

Table 4 Supported Phones

Supported Phones Supported Expansion Modules Supported Conference Stations

7902G 7914 7935
7905 7915-12 7936
7906G 7915-24 7937G
7910G 7916-12
7911G 7916-24
7912G
7920
7921G
7931G
7940G
7941G
7941G-GE
7942G
7945G
7960G – expansion module
compatible (7914)
7961G – expansion module
compatible (7914)
7961G-GE
7962G – expansion module
compatible (7915,7916)
7965G – expansion module
compatible (7915,7916)
7970G – expansion module
compatible (7914)
7971G – expansion module
compatible (7914)
7975G – expansion module
compatible (7915,7916)
7985G
ATA
CIPC – Cisco IP Communicator

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 7
 System Requirements

Supported Network Modules

Table 5 and Table 6 list the network modules that Cisco CP supports.

Table 5 Supported Network Modules

Wide Area
Enhanced Network Application Services Advanced Integration
Network Modules Modules (WAAS) Modules Modules (AIMs) Voice Network Modules
NM-4T NME-IPS-K9 NME-WAE-502-K9 AIM-VPN/BP II PLUS NM-HD-1V
NM-1FE2W-V2 NME-16ES-1G-P NME-WAE-522-K9 AIM-VPN/EP II PLUS NM-HD-2V
NM-1FE-FX-V2 NME-X-23ES-1G-P NME-WAE-302-K9 AIM-VPN/HP II PLUS NM-HD-2VE
NM-2FE2W-V2 NME-XD-24ES-1S-P AIM-VPN/SSL-1 NM-HDA-4FXS
NM-1FE-FX NME-XD-48ES-2S-P AIM-VPN/SSL-2 NM-HDV2
NM-4A/S NME-VMSS-16 AIM-VPN/SSL-3 NM-HDV2-1T1/E1
(synchronous only)
NME-VMSS-HP-16 AIM-IPS-K9 NM-HDV2-2T1/E1
NM-8A/S NME-VMSS-HP-32 AIM-CUE EVM-HD-8FXS/DID
(synchronous only)
AIM2-CUE-K9 EM-HDA-8FXS
NM-CIDS-K9
EM-HDA-4FXO
NM-16ESW
EM2-HDA-4FXO
NM-16ESW-1GIG
EM-HDA-3FXS/4FXO
NM-16ESW-PWR
EM-HDA-6FXO
NM-16ESW-PWR-1
GIG EM-4BRI-NT/TE
NMD-36ESW-PWR NM-CUE
NMD-36ESW-PWR- NM-CUE-EC
2GIG NME-CUE
EM3-HDA-8FXS/DID

Release Notes for Cisco Configuration Professional 2.0

8 OL-20446-01
 System Requirements

Table 6 Supported Cisco SRE Internal Service Modules and EtherSwitch Modules

Cisco SRE Internal Service Modules EtherSwitch Modules

ISM-SRE-300-K9 SM-ES2-16-P
SM-ES2-24
SM-ES2-24-P
SM-D-ES2-48
SM-ES3-16-P
SM-ES3G-16-P
SM-ES3-24-P
SM-ES3G-24-P
SM-D-ES3-48-P
SM-D-ES3G-48-P

Supported Interface Cards

Table 7, lists the interface cards that Cisco CP supports.

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 9
 System Requirements

Table 7 Supported Cards

WAN Interface Cards (WICs) High-speed WAN Interface Cards (HWICs) Voice Interface Cards
WIC-1T HWIC-1T VIC2-4FXO
WIC-2T HWIC-2T VIC2-2FXS
WIC-2A/S (Frame Relay, PPP, HWIC-4T VIC2-2FXO
HDLC, no asynchronous) HWIC-2A/S VIC2-2BRI-NT/TE
WIC-1ADSL HWIC-4A/S VIC-2DID
WIC-1DSU-T1-V2
HWIC-4ESW VIC-4FXS/DID
WIC-1B-S/T-V3 HWIC-4ESW-POE VIC3-4FXS/DID
WIC-1AM HWIC-8A VIC3-2FXS/DID
WIC-2AM
HWIC-8A/S-232 VWIC2-1MFT-T1/E
WIC-4ESW HWIC-D-9ESW VWIC2-2MFT-T1/E1
WIC-1SHDSL-V2 HWIC-D-9ESW-POE
WIC-1SHDSL-V3
HWIC-1DSU-T1
WIC 1ADSL-DG HWIC-16A
WIC 1ADSL-I-DG HWIC-ADSL-B/ST
HWIC-ADSLI-B/ST
HWIC-1ADSL
HWIC-1ADSLI
HWIC-1ADSL-M (WIC card with Annex M)
HWIC-2SHDSL
HWIC-4SHDSL
HWIC1-ADSL-M
HWIC-1CABLE-D-2
HWIC-1CABLE-E/J-2
HWIC-1FE
HWIC-2FE
HWIC-AP-AG-A
HWIC-AP-AG-E
HWIC-AP-AG-J
HWIC-AP-G-A
HWIC-AP-G-E
HWIC-AP-G-J
HWIC-3G-GSM
HWIC-3G-CDMA-S
HWIC-3G-CDMA-V

Release Notes for Cisco Configuration Professional 2.0

10 OL-20446-01
 System Requirements

Supported Adapters, Processing Engines, and Service Engines

Table 8 lists the adapters, processing engines, and service engines that Cisco CP supports.

Table 8 Supported Adapters, Processing Engines, and Service Engines

Port Adapters on Cisco Service Adapters

7000 Series Routers on Cisco 7000 Network Processing Engines and Network Service
Series Routers Engines on Cisco 7000 Series Routers
PA-2FE-TX SA-VAM NPE-225
PA-2FE-FX SA-VAM2 NPE-400
PA-8E SA-VAM2+ NPE-G1
PA-4E C7200-VSA NPE-G2
NSE-1

Cisco IOS Releases

Cisco CP is compatible with the Cisco IOS releases listed in Table 9.

Table 9 Cisco CP-Supported Routers and Cisco IOS Versions

Router Model Earliest Cisco CP-Supported Cisco IOS Versions

Cisco 815 • 12.4(11)T
Cisco 850 series • 12.4(9)T
Cisco 861 • 12.4(20)T
Cisco 867 • 15.0(1)M
Cisco 870 series • 12.4(9)T
Cisco 881 • 12.4(20)T
Cisco 886 • 15.0(1)M
Cisco 887 • 15.0(1)M
Cisco 888 • 12.4(20)T
Cisco 890 series • 15.0(1)M
Cisco 1801 • 12.4(9)T
Cisco 1802
Cisco 1803
Cisco 1805 • 12.4(15)XY
Cisco 1811 • 12.4(9)T
Cisco 1812
Cisco 1841 • 12.4(9)T
Cisco 1861 • 12.4(20)T
Cisco 1941 • 15.0(1)M
Cisco 1941W
Cisco 2800 series • 12.4(9)T

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 11
 System Requirements

Table 9 Cisco CP-Supported Routers and Cisco IOS Versions (continued)

Router Model Earliest Cisco CP-Supported Cisco IOS Versions

Cisco 2900 series • 15.0(1)M
Cisco 3800 series • 12.4(9)T
Cisco 3900 series • 15.0(1)M
Cisco 7000 • 12.4(9)T

Determining the Cisco IOS Release

To determine the release of Cisco IOS software currently running on your Cisco router, log in to the
router and enter the show version EXEC command. The following sample output from the show version
command indicates the Cisco IOS release on the second output line:
Router> show version
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (c1700-k8sv3y7-mz) Version 12.2(13)ZH

Required IP Address Configuration Information

Table 10 provides the required IP address configuration for the PC. Use this information to complete the
section “Task 4: Configure the IP Address On the PC” in the Cisco Configuration Professional Quick
Start Guide.
Table 10 Required PC IP Address Configurations

Router Model DHCP Server Required PC IP Address Configuration

Cisco 815, Cisco 85x, Cisco 86x, Cisco Yes Obtain an IP address automatically.
87x, Cisco 88x, Cisco 89x, Cisco 180x,
Cisco 1805, Cisco 1811 and 1812
Cisco 1841, Cisco 1861, Cisco 28xx, No Static IP address from 10.10.10.2 to
Cisco 38xx 10.10.10.6
Subnet Mask: 255.255.255.248

Release Notes for Cisco Configuration Professional 2.0

12 OL-20446-01
 System Requirements

Router Configuration Requirements

In order to run Cisco CP, a router configuration must meet the requirements shown in Table 11.

Table 11 Router Configuration Requirements

Feature Requirement Configuration Example

Secure access SSH and HTTPS Router(config)# ip http secure-server
Router(config)# line vty 0 4
Router(config-line)# transport input ssh
Nonsecure access Telnet and HTTP Router(config)# ip http server
Router(config)# line vty 0 4
Router(config-line)# transport input telnet
User privilege level 15 Router(config)# username cisco privilege 15 secret 0 cisco

The default configuration file meets all Cisco CP requirements. The default configuration file has the
name cpconfig-model_number.cfg. For example, the configuration file for the Cisco 860 and Cisco 880
routers is cpconfig-8xx.cfg.

Cisco CP Ordering Options

Table 12 on page 13 describes the ordering options under which Cisco CP can be ordered.
Cisco Configuration Professional Express (Cisco CP Express) is a product that is shipped in router flash
memory when the router is ordered with Cisco CP.

Table 12 Cisco CP Ordering Options

Ordering Options Description

CCP-CD Cisco CP: Shipped on CD
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory and in
NVRAM
CCP-CD-NOCF Cisco CP: Shipped on CD
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory

Note This ordering option does not provide the default configuration
file for Cisco 800 series routers.

CCP-EXPRESS Cisco CP: Not shipped

Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory and in
NVRAM

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 13
 New and Changed Information

Table 12 Cisco CP Ordering Options

Ordering Options Description

CCP-EXPRESS-NOCF Cisco CP: Not shipped
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory

Note This ordering option does not provide the default configuration
file for Cisco 800 series routers.

ISR-CCP-CD= Cisco CP: Shipped on CD

Spare SKU: Mapped to ISR-CCP-CD
ISR-CCP-CD Cisco CP: Shipped on CD
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory and in
NVRAM
ISR-CCP-CD-NOCONF Cisco CP: Shipped on CD
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory
ISR-CCP-EXP Cisco CP: Not shipped
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory and in
NVRAM
ISR-CCP-EXP-NOCONF Cisco CP: Not shipped
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory

New and Changed Information

This section contains new information about Cisco CP, and any information about Cisco CP that has
changed.
This section contains the following parts:
• New Features
• New Hardware Support

Release Notes for Cisco Configuration Professional 2.0

14 OL-20446-01
 New and Changed Information

New Features
Cisco CP 2.0 supports the following new features:
• Import and Export Community— The Import and Export Communities feature allows you to save
(export) the information about all the communities in Cisco CP to a file on your PC, and then import
that information from your PC into Cisco CP.
• License Management—The Cisco License Management feature allows you to register and manage
feature licenses by securely communicating with the Cisco Product License Registration portal
(Cisco licensing portal) to obtain the license, and then allows you to install and deploy the license
on a selected device.
• User Profile—Earlier you were allowed to access only certain domains or screens. For example, the
security administrator was allowed access only to the security screens and the network administrator
had access only to the routing screens. With the User Profile feature, you can choose a view for each
router. The views are Routing, Security, Voice, Default and so on. You can select read or read-write
for each feature displayed in the view.
• Template Support—Using this feature, you can generate a template from the running configuration
of a device, modify parameters as needed, and apply to the same or another device.
• Cellular WAN—This feature supports Third Generation (3G) Wireless High-Speed WAN interface
Card (HWIC). The HWIC will function as any other WAN interface on Cisco 1841, 28xx, and 38xx
routing platforms. For 881G, 886G, 887G, and 888G, this feature is available in a PCMCIA form.
Cisco CP 2.0 provides the following features to support 3G HWIC:
– Creating a cellular interface for CDMA (Sprint), CDMA (Verizon) and GSM HWICs
– Editing the existing cellular interface
– Deleting the cellular interface configurations
– Monitoring the cellular interfaces
• Module Configuration—The new Internal Service Modules (ISM) allows installation and
uninstallation of Cisco Unity Express and AXP applications. Cisco CP 2.0 displays the modules
available and also the currently installed application. Cisco CP 2.0 also provides funtionalities to
change the application or install a new application on the module.
• Module Power Management—This feature allows you to turn power on and off for the new ISM
modules.
• Flash File Management—ISR-G2 routers have two flashes. In that case, you need to select the flash
you want to save in.
• Dial Plan—All dial plan related features are enhanced so that apart from basic common use cases,
you can also change some of the advanced configuration options for dial plans. These include
Incoming Dial Plan, Outgoing Dial Plan, Intersite VoIP, Gateway VoIP, and SRST Rerouting.
• Trunk Group—Cisco CP 2.0 allows creation of trunk group by associating multiple trunks to create
the group. Cisco CP also provide the functionality to create dial-peer and associate it to trunk group.
This reduces the number of CLIs generated for dial-plan feature when dial-plan has to be applied to
multiple trunks.

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 15
 New and Changed Information

• Advanced Global Parameters—The Advanced Global Parameters feature allows you to enable or
disable VoIP parameters and to manage Voice Class Codec entries.
– Voice Class Codec—The Voice Class Codec feature enables a Cisco device to connect to other
VoIP devices without having prior knowledge about the codec that is used in a call-setup.
– VoIP Parameters—The VoIP Parameters feature allows you to enable or disable connections
between specific types of end points; and to enable or disable supplementary services.
Supplementary services are used for call transferring, call forwarding, and message waiting
indication (MWI) capabilities across a VoIP network.
• CME as SRST—Cisco Unified CME 4.0 provides fallback functionality to IP phones that are
registered to Call Manager. When connectivity to the Call Manager is lost or when the server goes
down, the phones re-home and register with CME which is configured to provide SRST services.
This solution provides access to all the features that CME normally provides while the phones are
in fallback mode without any additional licensing cost.
• Extension Templates - The Extension Templates feature allows you to apply a standard set of
features such as Pickup Group Number, Call Forward Busy Number, and Call Forward No Answer
Number to extensions.

New Hardware Support

The new devices supported are:
• CISCO1941/K9
• CISCO1941W-A/K9
• CISCO1941W-E/K9
• CISCO1941W-P/K9
• CISCO1941W-N/K9
• CISCO2901/K9
• CISCO2911/K9
• CISCO2921/K9
• CISCO2951/K9
• CISCO3925/K9
• CISCO3945/K9

Release Notes for Cisco Configuration Professional 2.0

16 OL-20446-01
 Limitations and Restrictions

The new network modules supported are:

• SM-ES2-16-P
• SM-ES2-24
• SM-ES2-24-P
• SM-D-ES2-48
• SM-ES3-16-P
• SM-ES3G-16-P
• SM-ES3-24-P
• SM-ES3G-24-P
• SM-D-ES3-48
• SM-D-ES3G-48-P
• ISM-SRE-300-K9
• AIM2-CUE-K9
• EM3-HDA-8FXS/DID

Limitations and Restrictions

This section describes restrictions and limitations that may apply to Cisco CP. It contains the following
parts:
• Cisco CP Requirements to Run on Microsoft Windows Vista
• Cisco CP Minimum Screen Resolution
• Restrictions for Cisco 7204VXR, Cisco 7206VXR, and Cisco 7301 Routers
• Cisco CP and Internet Explorer 8

Cisco CP Requirements to Run on Microsoft Windows Vista

In order to run Cisco CP under Microsoft Windows Vista, Cisco CP must be installed in Administrator
mode. You can do this by following the Microsoft Windows instructions to create an administrative
account, and then logging on to the PC using that account name and password before installing Cisco CP.
Failure to do this will require you to right-click on the Cisco CP icon or menu item, and choose “Run as
administrator” each time you want to run Cisco CP.

Cisco CP Minimum Screen Resolution

Cisco CP requires a screen resolution of at least 1024 x 768.

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 17
 Important Notes

Restrictions for Cisco 7204VXR, Cisco 7206VXR, and Cisco 7301 Routers
The following restrictions apply to Cisco CP running on Cisco 7204VXR, Cisco 7206VXR, and Cisco
7301 Routers:
• The Cisco CP Express application is not supported. You must use the Cisco IOS CLI to give the
router an initial configuration that will enable you to connect to the router using a browser.
• WAN configuration is not supported. Cisco CP supports configuration of Ethernet and Fast Ethernet
interfaces.
• The Cisco CP Reset feature is not available.
• No default configuration file is supplied. To run Cisco CP, you must provide a configuration that
includes the commands necessary to support operation of Cisco CP.

Cisco CP and Internet Explorer 8

In some systems (Windows XP and Windows Vista), with IE8 installed, Cisco CP may not work as
expected. This is due to a reported IE 8 caching issue.
IE8 reinstall or clearing the cache does not help. Any Flash based application like Cisco CP will see this
issue.
A workaround today is to create another user account with appropriate privileges and run Cisco CP in
that user account.
A fix will be made available in Cisco CP 2.1.

Important Notes
This section contains important information for Cisco CP. It contains the following sections:
• Cisco IOS Enforces One-Time Use of Default Credentials
• Cisco CP Merge and Replace Configuration Functions Fail Under Some Conditions
• Cisco CP Security Dashboard May Display Threats Unrelated to Your Cisco IOS IPS Installation
• Cisco CP May Lose Connection to Network Access Device
• Popup Blockers Disable Cisco CP Online Help
• Disable Proxy Settings
• Security Alert Dialog May Remain After Cisco CP Launches
• Screencasts for Cisco CP Features

Release Notes for Cisco Configuration Professional 2.0

18 OL-20446-01
 Important Notes

Cisco IOS Enforces One-Time Use of Default Credentials

To address CSCsm25466, Cisco IOS images included with recent shipments of Cisco 800, Cisco 1800,
Cisco 2800, and Cisco 3800 routers, enforce the one-time use of the default user name and password
provided in the Cisco CP configuration file. If you bypass Cisco CP or Cisco CP Express and use a
console or Telnet connection to log into the router, the login and exec banners warn you that you must
change the user name “cisco” and password “cisco” before you log off of the router. If you do not change
the credentials as directed, you will not be able to log on to the router the next time that you attempt to
do so.
The following Cisco IOS releases enforce the one-time use of the default credentials:
• 12.4(11)T or later
• 12.4(11)SW, 12.4(11)SW1, 12.4(11)XV, 12.4(11)XJ
• 12.4(9)T5, 12.4(9)T6
• 12.3(21), 12.3(22)
Follow the procedure in this section to secure the router by creating a new username and password, to
remove the login banner and exec banner warnings, and to save the configuration changes to the router
startup configuration.

Note If you login to the router using a Telnet or a console connection but do not complete the steps in this
procedure, be aware of the following:
• If you do not change the default username and password, and then log off the router, you will not be
able to log into the router again without entering the reload command. No additional warning is
given before you log off.
• If you do not change the default username and password, but do enter the write memory command
before ending the session, future logins will be disabled. In this case, you will need to follow the
password recovery procedure at the following link:
http://www.cisco.com/en/US/products/sw/iosswrel/ps1831/products_tech_note09186a00801746e6.sht
ml

To secure the router, remove the banner warnings and save the changes to the router startup config,
complete the following steps:

Step 1 Connect the light blue console cable, included with your router, from the blue console port on your router
to a serial port on your PC. Refer to your router’s hardware installation guide for instructions.
Step 2 Connect the power supply to your router, plug the power supply into a power outlet, and turn on your
router. Refer to your router’s quick start guide for instructions.
Step 3 Use HyperTerminal or a similar terminal emulation program on your PC, with the terminal emulation
settings of 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control, to connect to your router.
Step 4 When prompted, enter the username cisco, and password cisco.
Step 5 Enter configuration mode by entering the following command:
yourname# configure terminal

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 19
 Important Notes

Step 6 Create a new username and password by entering the following command:
yourname(config)# username username privilege 15 secret 0 password

Replace username and password with the username and password that you want to use.
Step 7 Remove the default username and password by entering the following command:
yourname(config)# no username cisco

Step 8 To remove the login banner, enter the following command:

yourname(config)# no banner login

The login banner warning will no longer appear.

Step 9 To remove the exec banner, enter the following command:
yourname(config)# no banner exec

The exec banner warning will no longer appear.

Step 10 Leave configuration mode, by entering the following command:
yourname(config)# end

Step 11 Copy the configuration changes to the startup configuration by entering the following command:
yourname# copy running-config startup-config

When logging into the router in the future, use the username and password that you created in Step 6.

Cisco CP Merge and Replace Configuration Functions Fail Under Some

Conditions
The problem described here is caveat CSCsj21989. If you attempt to merge configuration changes made
using the Cisco CP Config Editor feature, or replace the running configuration with a configuration from
the Config Editor, the router configuration will not be changed if there is a network device with a
Network Address Translation (NAT) IP address, or a cache engine in the connection between the PC and
the router. If you need to make changes to the router configuration that you would normally make using
the Cisco CP Config Editor, use the Cisco IOS CLI instead.

Cisco CP Security Dashboard May Display Threats Unrelated to Your Cisco IOS
IPS Installation
Some (or all) of the top threats you obtain using the Cisco CP Security Dashboard may not pertain to
your Cisco IOS IPS installation. After you deploy the signatures applicable to the top threats displayed
by the Cisco CP Security Dashboard, the dashboard may still display some (or all) top threats with a red
icon because applicable signatures could not be found. Those remaining top threats are unrelated to your
Cisco IOS IPS installation and not a danger to your router running Cisco IOS software.

Release Notes for Cisco Configuration Professional 2.0

20 OL-20446-01
 Important Notes

Cisco CP May Lose Connection to Network Access Device

This note concerns the Network Admission Control (NAC) feature.
If the PC used to invoke Cisco CP returns a posture state (Healthy, Infected, Checkup, Quarantine, or
Unknown) and if the group policy on the ACS server attached to the posture token assigned to the PC
has a redirect URL configured, the connection between Cisco CP and the router acting as the Network
Access Device (NAD) may be lost. The same problem can occur if an exception list entry attached to a
policy with a redirect URL is configured with the IP address or MAC address of the PC.
If you try to reinvoke Cisco CP from this PC, you will not be able to do so because the browser will be
redirected to the location specified in the redirect URL.
There are two workarounds for this problem:
• Ensure that the PC that you use to invoke Cisco CP attains a posture token which has an associated
group policy on the ACS server that is not configured with a redirect URL.
• Alternatively, use Cisco CP to create a NAC exception list entry with the IP address or MAC address
of the PC you use to invoke Cisco CP. Note that the exception list entry created for the PC should
be associated to an exception policy which does not have a redirect URL configured in it.
For more information, see the links in the Cisco CP NAC online help pages.

Popup Blockers Disable Cisco CP Online Help

If you have enabled popup blockers in the browser you use to run Cisco CP, online help will not appear
when you click the help button. To prevent this from happening, you must disable the popup blocker
when you run Cisco CP. Popup blockers may be enabled in search engine toolbars, or may be standalone
applications integrated with the web browser.
Microsoft Windows XP with Service Pack 2 blocks popups by default. In order to turn off popup
blocking in Internet Explorer, go to Tools > Pop-up Blocker > Turn Off Pop-up Blocker.
If you have not installed and enabled third-party pop up blockers, go to Tools >Internet Options >
Privacy, and uncheck the Block popups checkbox.

Disable Proxy Settings

Cisco CP will not start when run under Internet Explorer with proxy settings enabled. To correct this
problem, choose Internet Options from the Tools menu, click the Connections tab, and then click the
LAN settings button. In the LAN Settings window, disable the proxy settings.

Security Alert Dialog May Remain After Cisco CP Launches

When Cisco CP is launched using HTTPS, a security alert dialog box that informs you of possible
security problems and asks you if you want to proceed with program launch may appear. This can happen
if the router does not have the following global configuration command in the running configuration:
ip http timeout-policy idle 600 life 86400 requests 10000

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 21
 Important Notes

Screencasts for Cisco CP Features

Instead of online help, we have provided screencasts for the following Cisco CP 2.0 features:
• User Profiles
• Templates
• Cellular WAN
• CME as SRST
• Dial Plan (updated to include Trunk Groups)
• Module Configuration
• Module Power Management
• Extension Templates
• License Management (For this feature, we have provided online help as well as a screencast.)
These screencasts are located at:
http://www.cisco.com/en/US/docs/net_mgmt/cisco_configuration_professional/scrcst/ccpsc.html
You must have internet access to view the screencasts.

Cisco Configuration Professional Is Already Running Message

If Cisco CP has not been shut down properly, and you try to relaunch it, you may see the following
message: “Cisco Configuration Professional is already running. Only one occurrence can run at a time.”
To correct this problem and relaunch Cisco CP, do the following:

Step 1 Press Ctrl Alt Delete, and click Task Manager.

Step 2 In the Windows Task Manager dialog, click Processes.
Step 3 In the Image Name column, highlight the processes CiscoCP.exe, CiscoCPEngine.exe, IEC2.exe, and
SplashScreen.exe.
Step 4 Click End Process.
Step 5 Wait 30 seconds, and then restart Cisco CP.

Technical Support Logs Do Not Appear on Desktop

If the technical support logs folder does not appear on the desktop, there may be installed Java
applications preventing this feature from working properly. To check, go to Start > Control Panel >
Add or Remove Programs, and scan the list for Java applications. Remove the Java applications that
you can, and try again.

Release Notes for Cisco Configuration Professional 2.0

22 OL-20446-01
 Caveats

Discovery Never Completes

Because of Microsoft Windows Java caching issues, Cisco CP is sometimes unable to complete
discovery of a device. To fix this issue, complete the following steps:

Step 1 Choose Application > Exit to shut down Cisco CP.

Step 2 Go to Start > Control Panel > Java. The General tab is displayed.
Step 3 In the Temporary Internet Files box, click Delete Files.
Step 4 In the displayed dialog, leave all file types checked, and click OK.
Step 5 Click OK in the Java control panel to close it.
Step 6 Restart Cisco CP.

Caveats
Caveats describe unexpected behavior in Cisco CP. This section contains the following:
• Resolved Caveats from Cisco CP 1.4
• Open Caveats—Cisco CP 2.0

Resolved Caveats from Cisco CP 1.4

Table 13 lists caveats that are resolved in Cisco CP 2.0.

Table 13 Resolved Caveats in Cisco CP 2.0

Bug ID Summary
CSCsy50471 Enable option should not be shown when the VDSL interface is up.
CSCsl65044 Array values displayed when the mouse is placed over list in the user screen.
CSCsq52996 Need to support SIP for self zone in Cisco CP.
CSCsy06399 Error #2032 is seen on the Router Status dialog box.
CSCtb14050 Cisco CP hangs when trying to upload files through SSL VPN.
CSCta95900 CSCta95900 - Outgoing dial plan configures invalid destination pattern.
CSCtb07893 Acknowledge error on importing Outgoing dial plan in the offline mode.
CSCta12755 Configuration failed when trying to deliver CLIs to the router.
CSCta65551 DID trunk configuration is failing in Online mode.
CSCta86408 Device needs to be discovered after moving to the online mode.
CSCta93218 Disabling CLI view in online mode causes CLIs to be sent directly.
CSCta95721 EM-4BRI-NT/TE ports under EVM-HD-8FXS/DID not getting discovered.
CSCtb03710 PRI Settings voice port values are not displayed correctly.

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 23
 Caveats

Table 13 Resolved Caveats in Cisco CP 2.0 (continued)

Bug ID Summary
CSCtb05571 Forward PSTN access digit does not work.
CSCtb10599 Switching between devices in the offline mode shows incorrect data.
CSCtb14313 Cisco CP allows class removal with Firewall PT in GETVPN.
CSCtb24637 Post install fails for Pano device.
CSCtb25590 Deleting multiple extensions throws exception.

Open Caveats—Cisco CP 2.0

Table 14 lists caveats that are open in Cisco CP 2.0.

Table 14 Open Caveats in Cisco CP 2.0

Bug ID Summary Additional Information

CSCsm91019 Security screens overlap Symptom: Some of the menu bar options, either Tools or
over menu bar options and Help. are hidden under security screens.
tool bar information.
Conditions: You are in Routing or Security features
screen while selecting the menu options.
Workaround: Move to any other feature other than
Routing or Security, the issue will not be seen.
CSCsm95507 Cisco CP icon is changed Symptom: The icon of Cisco CP application window
to Internet Explorer icon changes to Internet Explorer icon.
after a while in the titlebar.
Conditions: After the successful launch of Cisco CP,
minimize the Cisco CP screen and keep it minimized for
a while.
Workaround: There is no workaround.
CSCsw23556 Security Applet is not Symptom: Discovery of a device failed with the error
responding error during Security Applet not responding.
discovery.
Conditions: This issue happens intermittently.
Workaround: Re-launch the application.
CSCsw31280 CLI Preview dialog box Symptom: When configuring security features, you click
moves to the background. the Add, Edit, or other command buttons in the user
interface, the dialog boxes do not open.
Conditions: CLI Preview dialog box is not closed and is
present in the background.
Workaround: Resize or move the main Cisco CP window
and complete the CLI preview dialog options that are
hidden in the background to continue.

Release Notes for Cisco Configuration Professional 2.0

24 OL-20446-01
 Caveats

Table 14 Open Caveats in Cisco CP 2.0 (continued)

Bug ID Summary Additional Information

CSCsw39659 Enhancement in Cisco CP Symptom: The data fields for CUE post initialization
for CUE post initialization. wizard are not retained on Cisco CP if you use the back
button. It is time consuming to enter all the values again.
Conditions: This issue occurs only when any field value
is invalid in the CUE post initialization wizard.
Workaround: To avoid this situation, make sure that you
enter the correct values so that you do not have to use the
back button.
CSCsx05868 Unable to upload CME Symptom: In Cisco Configuration Professional, while
phone load tar file. trying to upload phone load tar file from the Voice >
Phone Firmware feature, phone load upload might fail
after some upload progress.
Conditions: On device if exec-timeout</CmdBold> is
not set under line vty</CmdBold> configurations or if
exec-timeout</CmdBold> is set with a smaller timeout
value, then phone load upload might fail.
Workaround: On device, under all line vty</CmdBold>
configs, set exec-timeout</CmdBold> config with
proper timeout value. Example: vty line 0 4
exec-timeout 25 0 exit

Further Problem Description: exec-timeout is used to

set the interval that the EXEC command interpreter waits
until user input is detected. If no input is detected during
this interval, the EXEC facility returns the terminal to the
idle state and disconnects the incoming session. A big size
phone load tar file might take some time to get uploaded
on the device’s flash. So to avoid any error during upload,
exec-timeout should be set with a value greater than the
time taken by upload of big tar file. If exec-timeout is set
as 0 0, then vty lines may get blocked if session is not
exited/closed properly.
CSCsx57080 Cisco CP launching issue Symptom: Unable to launch Cisco CP.
with Internet Explorer 8.
Conditions: Using Internet Explorer 8 release candidate
1.
Workaround: Downgrade to Internet Explorer 7.
CSCsx72139 Cisco CP discover details Symptom: Voice menu folder is disabled in the Cisco CP
should give warning in case GUI.
of insufficient memory.
Conditions: The router running IOS version 12.4(24)T or
later has insufficient memory to enable telephony-service.
Workaround: Upgrade the DRAM in the router.

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 25
 Caveats

Table 14 Open Caveats in Cisco CP 2.0 (continued)

Bug ID Summary Additional Information

CSCsx75097 Unity express module Symptom: Cisco Unity Express module discovery fails
discovery fails with SSH with an error message stating that the device is configured
version >=2.0. with unsupported SSH version. The error messages are
shown in the discovery details user interface. Due to this
error message, none of the CUE features are available.
Conditions: The device is configured with SSH version
higher than or equal to 2.0.
Workaround: Reconfigure the SSH version to lesser than
2.0, or use Telnet to communicate with the device.
CSCsy49785 Service group not working Symptom: OGACL with service group not working for
for QoS, SSLVPN, NAC, QoS, SSLVPN, NAC, and access-class.
and access-class.
Conditions: When associating an OGACL with service
object group to QoS, SSL VPN, NAC, and access-class,
the traffic does not match. This is due to an IOS issue.
Workaround: There is no specific workaround. Use
normal ACLs with these features. Once the IOS bug is
fixed, this will be fixed in Cisco CP.
CSCsy87964 CPU utilization at 100% Symptom: After discovery of 5 devices in a community,
when discovering devices. some with secure mode, CPU shoots to 100% utilization
and does not drop. CiscoCPEngine.exe CPU usage is in
the range 83%-95%.
Conditions: This problem occurs if one of the devices in
the community, has high security configuration and
bandwidth filters for the WAN interface. This problem
does not occur in other PC environments.
Workaround: There is no workaround.

Release Notes for Cisco Configuration Professional 2.0

26 OL-20446-01
 Caveats

Table 14 Open Caveats in Cisco CP 2.0 (continued)

Bug ID Summary Additional Information

CSCsz13428 Configuration error on Symptom: Dial-plan related configuration fails saying
creating or editing dial-peer tag is already in use. This issue occurs
outgoing dial-plan. occasionally when voice hunt-group is configured on the
router.
Conditions: When hunt-group is configured with pilot
CLI, and the pilot number is too huge to be the dial-peer
tag.
Further Problem Description: When hunt-group is
configured with pilot CLI, the router creates a dial-peer
with the pilot number as the dial-peer tag. This dial-peer
is not displayed in show run, and Cisco CP does not read
these dial-peers (only show run is used to read in
dial-peer configurations). However, these dial-peers can
be seen in show dial-peer voice summary.
In normal circumstances, the pilot number and the
dial-peer tag are large numbers. This is not an issue for
Cisco CP as Cisco CP always chooses the smallest tag
number available to configure dial-peers and there is
never any overlap of tags. However, if the pilot number is
too large to be a tag for dial-peer, the router chooses the
next available smallest tag number to configure the
dial-peer for that hunt group. In such a situation, Cisco CP
configuration for dial-plan might cause a problem
because the tag that Cisco CP chooses, can overlap with
the already configured hunt group related dial-peer, which
results in configuration failure.
CSCsz13759 Deleting of extensions fails Symptom: Error while deleting multiple extensions
if configured as together.
Monitor/Shared.
Conditions: Create 6 extensions. For example, 1000,
2000, 3000, 4000, 5000, 6000.
Assign extensions 1000, 2000, 3000 on button 1 of user1;
and extensions 4000, 5000, 6000 on button 2 of user1.
Assign extension 1000, 2000, 3000, 4000, 5000, 6000 on
button1 of user2. Assign extension 1000 on button1 of
user3.
Try to delete all the extensions together.
Workaround: Delete the extensions one by one.
CSCta31020 Whisper intercom does not Symptom: No error message while editing invalid
throw error while editing Whisper Intercom entry.
an invalid entry.
Conditions: Whisper intercom dashboard should have
invalid entry. Invalid entry should be created via the CLI.
Workaround: There is no workaround.

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 27
 Caveats

Table 14 Open Caveats in Cisco CP 2.0 (continued)

Bug ID Summary Additional Information

CSCta60741 Unable to add inspect rule Symptom: Inspect rule does not get configured correctly
to self zone when editing for the SSL VPN Passthrough.
ZBF.
Conditions: Configure ZBF and then configure SSL
VPN. The inspect rule does not get configured correctly.
This is due to an IOS bug.
Workaround: There is no workaround.
CSCta77317 Analog Trunk window not Symptom: Go to Configure > Voice > PSTN Trunks >
closing on clicking the OK Analog Trunks. The Edit screen does not close when the
button. OK button is clicked without making any changes.
Conditions: Go to Configure > Voice > PSTN Trunks >
Analog Trunks screen. Select an entry, and then click
Edit. Without making any changes, click OK. The dialog
box does not close.
Workaround: Click Cancel button.
CSCta77454 Adhoc Conference update Symptom: Although Discovery is successful with SSH
with SSH port blocked port blocked, updates on Adhoc Conference fail as
throws unwarranted error. interactive commands use SSH protocol. The error
message does not indicate that the SSH port is blocked.
Conditions: Modification of Adhoc Conference
parameters fail with SSH port blocked and the error
message does not indicate the cause.
Workaround: Unblock the SSH port for any
transport/communication errors on Adhoc Conference.
Further Problem Description: The Discovery process
on Cisco CP is successful with SSH port blocked but
features like Adhoc Conference use DSPs which interact
using SSH ports. When the SSH port is blocked, all such
interactions fail and hence updates on Adhoc Conference
profile are not successful.The error message generated
does not communicate the cause.
CSCtb05983 Multiple delete fails in Symptom: Devices do not disappear from the community
offline mode community table immediately after deleting them.
dashboard.
Conditions: Select multiple devices in the offline mode
and press Delete.
Workaround: Delete the devices one by one.
Or
Refresh the community table after all the devices are
deleted.

Release Notes for Cisco Configuration Professional 2.0

28 OL-20446-01
 Caveats

Table 14 Open Caveats in Cisco CP 2.0 (continued)

Bug ID Summary Additional Information

CSCtb81205 Location to download SDM Symptom: Latest SDM/CP packages for IPS cannot be
IPS packages needs to be auto downloaded using Cisco CP.
changed.
Conditions: If the user clicks “Download” option from
IPS, the latest SDM/CP package will not be downloaded.
Only the IOS-CLI package will be downloaded.
Workaround: Manually download the package from
CCO and use it in Cisco CP for configuration or import
options.
CSCtb58966 Reload of router Symptom: Reload of device unsuccessful after deploying
unsuccessful after license or when using 'Reload router' button from License
deploying license. Management > Dashboard window.
Conditions: This is seen with devices with an AP module
that requires an input to the following interactive
command.
cisco881GW#reload
Do you want to reload the internal AP? [yes/no]:
Workaround: Manually reload the router for the license
deployment to take effect and re-discover the router.
CSCtb43408 Dialer persistent config Symptom: No dialer persistent config delivered to the
conflicts with Do Not router.
Configure Now in wizard.
Conditions: Both dialer persistent and Do Not Configure
Now specified.
Workaround: There is no workaround.
CSCtb33162 Only the last chat script is Symptom: Only the last chat script gets removed upon
removed when multiple clicking the delete button for the specified interface.
chat is configured. Conditions: Configure multiple chat script under Dialer
tab in edit mode.
Workaround: There is no workaround.
CSCta71627 Dialer list configuration Symptom: Previous configured dialer-list gets removed.
removed after GSM wizard Conditions: There are two GSM interfaces, one is pre
configuration.
configured with dialer-list 2. While using the wizard to
configure the second interface, dialer-list 2 get removed.

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 29
 Caveats

Table 14 Open Caveats in Cisco CP 2.0 (continued)

Bug ID Summary Additional Information

CSCsx05868 Unable to upload CME Symptom: In Cisco Configuration Professional, while
phone load tar file. trying to upload phone load tar file from the Voice >
Phone Firmware feature, the upload may fail after some
upload progress.
Conditions: On the device, if
<CmdBold>exec-timeout</CmdBold> is not set under
<CmdBold>line vty</CmdBold> configurations, or if
<CmdBold>exec-timeout</CmdBold> is set with a
smaller timeout value, then phone load upload may fail.
Workaround: On the device, under all <CmdBold>line
vty</CmdBold> configs, set
<CmdBold>exec-timeout</CmdBold> config with
proper timeout value. For example:
vty line 0 4
exec-timeout 25 0
exit
Further Problem Description: exec-timeout is used to
set the interval that the EXEC command interpreter waits
until user input is detected. If no input is detected during
that interval, the EXEC facility returns the terminal to the
idle state and disconnects the incoming session.
A big size phone load tar file may take some time to get
uploaded on the device's flash. So to avoid any error
during upload, exec-timeout should be set with a value
greater than the time taken to upload a big tar file.
If exec-timeout is set as 0 0, then vty lines may get
blocked if the session is not exited or closed properly.
CSCtc30671 Issues with network object Symptom: The ACL network object groups do not get
ACL groups listed under the summary screen after creation.
The ACL object group created under one device gets
listed under a different device.
The network object group created under a device cannot
be applied under the ACL rule.
Conditions: The ACL network object groups do not get
listed under the summary screen after creation. The ACL
object group created under one device gets listed under a
different device.
This problem is seen when more than one device is
discovered.
Workaround: Rediscover the devices under Cisco CP.

Release Notes for Cisco Configuration Professional 2.0

30 OL-20446-01
 Related Documentation

Related Documentation
Table 14 describes the related documentation available for Cisco Configuration Professional.

Table 15 Cisco Configuration Professional Documentation

Document Title Available Formats

Readme First for This document is available in the following locations:
Cisco Configuration Professional
• On Cisco.com.
• On the product CD-ROM in the Documentation folder.
Cisco Configuration Professional This guide is available in the following locations:
Quick Start Guide
• On Cisco.com.
• On the product CD-ROM in the Documentation folder.
Cisco Configuration Professional This guide is available in the following locations:
Getting Started Guide
• On Cisco.com.
• On the product CD-ROM in the Documentation folder.
• During the installation process, just before you have finished
installing the product, you are provided the option to read the
Getting Started guide.
Cisco Configuration Professional This guide is available in the following locations:
User Guide
• On Cisco.com.
• Accessible from Online help.
Cisco Configuration Professional This guide is available in the following locations:
Express User Guide
• On Cisco. com.
• Accessible from Online help.
Release Notes for This document is available in the following location:
Cisco Configuration Professional
• On Cisco.com.
Release Notes for This document is available in the following location:
Cisco Configuration Professional
• On Cisco.com.
Express

Note For information on obtaining documentation and technical assistance, product security, and additional
information, see What's New, which also lists new and revised documents each month.

Release Notes for Cisco Configuration Professional 2.0

OL-20446-01 31
 Related Documentation

This document is to be used in conjunction with the documents listed in the “Related Documentation” section.

CCDE, CCENT, CCSI, Cisco Eos, Cisco HealthPresence, Cisco IronPort, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco Nurse Connect,
Cisco Pulse, Cisco StackPower, Cisco StadiumVision, Cisco TelePresence, Cisco Unified Computing System, Cisco WebEx, DCE, Flip Channels,
Flip for Good, Flip Mino, Flipshare (Design), Flip Ultra, Flip Video, Flip Video (Design), Instant Broadband, and Welcome to the Human Network
are trademarks; Changing the Way We Work, Live, Play, and Learn, Cisco Capital, Cisco Capital (Design), Cisco:Financed (Stylized), Cisco Store,
and Flip Gift Card are service marks; and Access Registrar, Aironet, AllTouch, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP,
CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems,
Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, Continuum, EtherFast, EtherSwitch, Event Center,
Explorer, Fast Step, Follow Me Browsing, FormShare, GainMaker, GigaDrive, HomeLink, iLYNX, Internet Quotient, IOS, iPhone, iQuick Study,
IronPort, the IronPort logo, Laser Link, LightStream, Linksys, MediaTone, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers,
Networking Academy, Network Registrar, PCNow, PIX, PowerKEY, PowerPanels, PowerTV, PowerTV (Design), PowerVu, Prisma, ProConnect,
ROSA, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx,
and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. (0908R)

Copyright © 2009 Cisco Systems, Inc. All rights reserved.

Release Notes for Cisco Configuration Professional 2.0

32 OL-20446-01