Rough Terrain Crane Specifications | RT200/200XL Cranes |

STANDARD BOOM EQUIPMENT

BOOM BOOM HEAD
30-94' (9.23-28.78 m), four section full power boom. Telescoping is Welded to outer section of boom. Four or five metallic load sheaves
mechanically synchronized with single lever control. the synchro- and two idler sheaves mounted on heavy duty, anti-friction bearings.
nization system consists of a single telescope cylinder and high Quick reeving boom head. Provisions made for side-stow jib mount-
strength leaf chains to extend and retract the third section and tip ing.
section. Boom is high strength four plate design,welded inside and
out, with anti-friction slide pads. Boom side plates are made with
stamped impressions to reduce weight and increase strength. A sin-
gle boom hoist cylinder provides for boom elevation of -4 to 76
degrees. All cylinders are equipped with integral hold valves.
Maximum tip height is 99' (30.17 m).

OPTIONAL BOOM EQUIPMENT

MAIN BOOM AUXILIARY BOOM HEAD
30-72' (9.23-22.19 m) three section full power boom OR 30-100' Removable auxiliary boom head has single metallic sheave mounted
(9.23-30.61 m) four section full power XL Series boom. on an anti-friction bearing. Removable pin-type rope guard for quick
reeving.Installs on main boom peak only
. Removal is not required for
Telescoping is mechanically synchronized with single lever control. jib use.
The synchronization system consists of a single telescope cylinder
and high strength leaf chains to extend and retract the tip section. HOOK BLOCK
Either boom is high strength four plate design,welded inside and
out, with anti-friction slide pads. Boom side plates are made with Two, three or four metallic sheaves on anti-friction bearings with
stamped impressions to reduce wight and increase strength. A single hook and hook latch. Quick reeving design does not require removal
boom hoist cylinder provides for boom elevation of -4 to 76 degrees. of wedge and socket from rope.
All cylinders are equipped with integral hold valves. Maximum tip
height is 72' (22.19 m) boom options 79' (24.23 m). Maximum tip HOOK & BALL
height with 100' (30.61 m) XL Series boom option is 107' (32.76 m) 7 ton (6.3 mt) top swivel ball with hook and hook latch

JIBS
26' (7.92 m) side stow swing-on one-piece lattice type jib. Single
metallic sheave mounted on anti-friction bearing. Jib is offsettable at
0º, 15º or 30º. With 100' (30.61 m) XL Series boom, maximum tip
height is 130' (39.62 m). 26-43' (7.92-13.11 m) side stow swing-on
lattice type jib. Single sheave mounted on anti-friction bearing. Jib is
extendible to 43' (13.11 m) by means of 17' (5.18 m) manual pull-
out tip section, roller supported for ease of extension. Jib is offset-
table at 0º, 15º or 30º. With 100' (30.61 m) XL Series boom, maxi-
mum tip height is 147' (44.80 m).
 ROUGH TERRAIN CRANE

RT200/200XL

STANDARD UPPERSTRUCTURE EQUIPMENT

UPPERSTRUCTURE FRAME
All welded one-piece structure fabricated with high tensile strength
alloy steel. Counterweight is bolted to frame.
TURNTABLE CONNECTION
CONTROLS
Swing bearing is a single row, ball type, with external teeth. The
swing bearing is bolted to the revolving upperstructure and welded All control levers and pedals are positioned for efficient operation.
to the carrier frame. Hand operated control levers include swing, telescope, boom hoist,
winch(s), shift, vernier adjustable hand throttle and 360º house lock.
SWING Switches include ignition, engine stop, two speed winch(s), lights,
horn, windshield wipers, defroster, steering mode, parking brake,
A hydraulic motor drives a double planetary reduction gear for pre- and outrigger controls. Foot control pedals include swing brake,
cise and smooth swing function. Swing speed (no load) is 3.0 rpm. boom raise, boom lower, service brakes and accelerator.
SWING BRAKE INSTRUMENTATION AND ACCESSORIES
Heavy duty multiple disc swing brake is mechanically actuated from In-cab gauges include air pressure, bubble level, engine oil pressure,
operator’s cab by foot pedal. Brake may be locked on or used as a fuel, engine temperature, voltmeter, transmission temperature, and
momentary brake. A separate 360º mechanical house lock is also transmission oil pressure. Indicators include low air, high water tem-
provided. perature/ low oil pressure/high transmission temperature audio/visu-
al warning, low coolant audio/visual warning, hoist drum rotation
RATED CAPACITY INDICATOR indicator(s), and Rated Capacity Indicator. accessories include fire
Rated Capacity Indicator with visual and audible warning system and extinguisher; light package including headlights, tail lights, dome
automatic function disconnects. Second generation pictographic dis- light, brake lights, directional signals, four-way hazard flashers,
play includes: boom radius, boom angle, boom length, allowable dome light, and back up lights with audio pulsating back-up alarm;
load, actual load, and percentage of allowable load registered by bar windshield washer/ wiper and skylight wiper, R.H. and L.H. rear view
graph. Operator settable alarms provided for swing angle, boom mirrors; dash lights; and seat belt. Circuit breakers protect electrical
length, boom angle, tip height, and work area exclusion zone. Anti- circuits.
two block system includes audio/visual warning and automatic func-
tion disconnects. HYDRAULIC CONTROL VALVES
Valves are mounted on the upperstructure and are easily accessible.
OPERATORS CAB Valves are mechanically operated and include one four spool valve
Environmental cab with all steel construction, optimized visibility, for boom elevation, telescope, main winch boost, and main winch;
tinted safety glass throughout, and rubber floor matting is mounted one single spool valve for swing. High pressure regeneration feature
on vibration absorbing pads. The cab has a sliding door on the left provides 2-speed boom extension. Quick disconnects are provided
side, framed sliding window on the right side, hinged tinted all glass for ease of installation of pressure check gauges.
skylight and removable front windshield to provide optimized visibili-
ty of the load open or closed. Acoustical foam padding insulates OPTIONAL EQUIPMENT
against sound and weather. The deluxe six-way adjustable operator’s Auxiliary Winch, Heater/Defroster, Air Conditioner, Work Lights,
seat is equipped with a mechanical suspension and includes head Revolving Amber Light, Independent Rear Wheel Steering, Roof
and arm rests Mounted Spotlight.

STANDARD CARRIER EQUIPMENT

CARRIER CHASSIS
High strength chassis with four-wheel drive and four-wheel steer
(4x4x4). Has box beam type construction with reinforcing cross
members, a precision machined turntable mounting plate and inte-
grally welded outrigger boxes. Decking has skid-resistant surfaces,
including tool storage compartment, and access steps and handles
left and right side and front and rear corners. SERVICE BRAKES
AXLES AND SUSPENSION Air over hydraulic drum type brakes on all four wheels: 17" x 4"
(43.18 x 10.2 cm) drum brakes
Rear axle is a planetary drive/steer type with 10.0" (0.25 m) of total
oscillation. Automatic oscillation lockouts engage when the super- PARKING BRAKE
structure is swung 10˚ in either direction. An oscillation lock out
override is provided. Front axle is a planetary drive/steer type, rigid Transmission mounted spring-set, air released external caliper disk
mounted to the frame for increased stability. type emergency/parking brake.
WHEELS & TIRES STEERING
Disc type wheels with full tapered bead seat rim. 134" (3.40 m) Hydraulic four-wheel power steering for two-wheel, four-wheel, or
wheelbase.
crab steer is easily controlled by steering wheel. A rear axle center-
TIRES ing light is provided.
Standard: 20.5 x 25,24 P.R. / Optional: 16.00 x 25, 28 P.R.
 ROUGH TERRAIN CRANE

RT200/200XL

STANDARD CARRIER EQUIPMENT (CONTINUED)

Turning radius to center of outside tire. MULTI-POSITION OUT & DOWN OUTRIG-
(16.00 x 25) (20.5 x 25) GERS
Two-wheel: 34’ 8.81" (10.5 m) 34' 10.38" (10.63)
Four-wheel: 19' 3.44 (5.88 m) 19' 5" (5.92 m) Fully independent hydraulic outriggers may be utilized fully extended, in their
1/2 extended position, or fully retracted. Easily removable steel floats, each
TRANSMISSION with an area of 2542 (1 639 cm2) stow on the carrier frame. Complete con-
torls and sight leveling bubble are located in the operators’ cab.
Range-shift type power-shift transmission with integral torque converter has
neutral safety start, 6 speeds forward, and 6 speeds reverse. Automatic pul-
sating back-up alarm. OPTIONAL EQUIPMENT
Cold Weather Starting Aid, Immersion Heater, Pintle Hook, Clearance Lights,
Front Mounted Winch - 20,000 lb (9 072 kg), Independent Rear or Four Mode
Rear Wheel Steer.

HYDRAULIC SYSTEM

HYDRAULIC PUMPS FILTRATION

Three gear type pumps, one single and two in tandem, driven off the trans- Full flow oil filtration system with bypass protection includes a removable 60
mission. Combined system capability is 113 gpm (427.7 lpm). Includes man- mesh (250 micron) suction screen-type filter and 5 micron replaceable return
ual pump disconnect. line filter.
Main Winch Pump
u 53 gpm (200.7 lpm) @ 3,500 psi (246.1 kg/cm2) HYDRAULIC RESERVOIR
Boom Hoist and Telescope Pump
u 39 gpm (147.6 lpm) @ 3,500 psi (246.1 kg/cm2) All steel, welded construction with internal baffles and diffuser. Provides easy
Power Steering, Outrigger and Winch Boost Pump access to filters and is equipped with an external sight level gauge. The
u 21 gpm (79.5 lpm) @ 2,500 psi (175 kg/cm2) Always live even when hydraulic tank is pressurized to aid in keeping out contaminants and in
pump disconnect is actuated. reducing potential pump cavitation. Capacity is 94 gal (355 liters). Swing-
away hydraulic oil cooler is standard
MAIN WINCH SPECIFICATIONS OPTIONAL HOIST LINE
Hydraulic winch with bent axis piston motor an planetary reduction provides Main winch and optional auxiliary winch: 5/8" (16 mm) rotation resistant
2-speed operation with equal speeds for power up and down. Winch is compacted strand 18 x 19 or 19 x 19. Min. breaking strength 22.6 tons (20.6
equipped with an integral automatic brake, a grooved drum with tapered mt).
flanges for improved rope spooling, a spring loaded cable roller and an elec-
tronic drum rotation indicator.
ENGINE SPECIFICATIONS
Performance LO-Range HI-Range Standard
u Max line speed (no load) Make and Model Cummins 6BTA5.9
u First layer 205 fpm (62.5 m/min) 329 fpm (100.3 m/min.) Type 6 Cylinder
u Fifth layer 297 fpm (90.5 m/min) 475 fpm (144.8 m/min.) Bore and Stroke 4.02x4.72" (102x120 mm)
Displacement 359 cu in (5.9 L)
u Max. line pull-first layer 12,512 lb (5 675 kg) 7,298 lb (3 310 kg) Max. Gross HP 130 hp (97 kw)@2500 rpm
u Max. line pull-fifth layer 8,662 lb (3 929 kg) 5,052 lb (2 292 kg) Max. Gross Torque 384 lb•ft (521 N•m) @1200 rpm
u Permissible line pull 9,000 lb (4 082 kg) Aspiration Turbocharged
Air Filter Dry Type
Drum Dimensions Drum Capacity Electrical System 12 volt
u 10.62" (270 mm) drum diameter Max. Storage: 598' (182.3 m) Alternator 102 amp
u 17.53" (445 mm) length 6th layer is not a working layer Battery (2) 12V-1600 C.C.A.
u 18.25" (464 mm) flange dia. Max. useable: 479' (146.0 m)* Fuel Capacity 50 gal (189 L)
u Cable: 5/8" x 450' (16 mm x 137.2 m)
u Cable type: 5/8" (16 mm) 6x19 IWRC IPS right regular lay, preformed.
u Min. breaking strength 17.9 tons (16.2 mt) PERFORMANCE (STANDARD ENGINE)
Trans- Max.
*Based on minimum flange height above top layer to comply with ANSI B30.5 mission Forward Max. Tractive Gradeability
Range Gear Drive Speed Effort @ Stall
OPTIONAL AUXILIARY WINCH Low 1 4-Wheel 2.3 mph 37,856 lb 112.34%
3.7 km/h 17 171 kg
Hydraulic winch with bent axis piston motor, power up and down, equal 2 4-Wheel 4.4 mph 19,254 lb 39.84%
speed, planetary reduction with integral automatic brake, cable roller, and 7.1 km/h 8 734 kg
rotation indicator. 3 4-Wheel 12.4 mph 6,431 lb 11.10%
20.0 km/h 2 917 kg
Performance (Same as main winch) High 1 2-Wheel 5.0 mph 16,893 lb 34.04%
8.0 km/h 7 663 kg
Drum Dimensions and Capacity (Same as main winch) 2 2-Wheel 9.5 mph 8,589 lb 15.59%
15.3 km/hr 3 896 kg
3 2-Wheel 24.5 mph 2,849 lb 3.77%
39.4 km/h 1 292 kg
All performance data is based on a gross vehicle weight of 52,000 lb (23 583
kg). 16:00 x 25 tires, 4x4 drive. Performance may vary due to engine perform-
ance. Gradeability data is theoretical and is limited by tire slip, machine stability,
or engine oil pan design.
GENERAL DIMENSIONS
1. Dimensions given assume the boom is fully retracted in travel position and 16:00 x 25 tires. 3. Track width: 6' 7.50" (2.02 m) 16:00 x 25 tires
20.5 tires reduce heights 1.0 (25 mm) 6' 10.5" (2.10 m) 20.5 x 25 tires

2. Minimum ground clearance under transmission - 20.62" (.52m) 4. Width of carrier: 8' (2.44 m) 16:00 x 25 tires
axle bowls - 19.12" (.49 m) 8' 8" (2.64 m) 20.5 x 25 tires
tire rods - 20.38" (.52 m)
Tire to frame angle 16:00 tires 20.5 tires
Approach angle: 25.1º 24.1º
Departure angle: 23.1º 22.2º

GROSS UPPER FACING GROSS UPPER FACING

WEIGHTS & FRONT WEIGHT FRONT
AXLE LOADS WEIGHT
LB FRONT REAR KG FRONT REAR
Basic Crane with 10,000 lb (4 536 kg) Counterweight 55,930 28,972 26,958 25 369 13 141 12 228
Add Options:
26' (7.92 m) Swing-on Jib (Stowed) + 1100 + 2,000 - 900 + 499 + 907 - 408
26'-43' (7.92-13.11 m) Swing-on Jib (Stowed) + 1500 + 2,600 - 1,100 + 680 + 1 179 - 499
Auxiliary Boom Head + 100 + 300 - 200 + 45 + 136 - 91
Auxiliary Winch with Wire Rope, Controls, Etc. + 115 - 25 + 140 + 52 - 11 + 63
30 ton (27.2 mt) 4 Sheave Hook Block + 655 + 1,071 - 416 + 297 + 486 - 189
30 ton (27.2 mt) 3 Sheave Hook Block + 670 + 1,099 - 429 + 304 + 498 - 194
25 ton (22.6 mt) 2 Sheave Hook Block + 682 + 1,117 - 435 + 309 + 507 - 198
7 ton (6.3 mt) Hook and Ball (in tool box) + 240 + 290 - 50 + 109 + 130 - 21
Pintle Hook: Front + 45 + 60 - 15 + 20 + 27 - 7
Rear + 45 - 25 + 70 + 20 - 11 + 31
Substitute:
72' (22.19 m) Full Power 3-Section Boom - 3190 - 4,335 + 1,145 - 1 445 - 1 965 + 520
100' (30.61 m) Full Power 4-Section Boom + 533 + 1,986 - 1,453 + 242 + 901 - 659
16.00 x 25 Tires - 360 - 180 - 180 - 164 - 82 - 82

Note:Weights are forTerex supplied equipment and are subject to 2% variation due to manufacturing tolerances.