Scribd
Upload
46 views

Parts Checklist For The Swede Kit: Resistors

The document provides a parts checklist for building The Swede Kit, including: - A list of resistors with quantities and values needed - A list of capacitors with quantities, values, and identification codes needed - A list of diodes, ICs, transistors, potentiometers, and other hardware included in the kit - Instructions for differentiating resistor and capacitor values and notes on preparing potentiometers - Diagrams showing foot switch solder lug designations and instructions for wiring the foot switch The checklist contains all the electronic components, hardware, and basic instructions required to construct the effect pedal circuit called The Swede from a build-it-yourself kit.

Uploaded by

Alex Arm.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
46 views

Parts Checklist For The Swede Kit: Resistors

The document provides a parts checklist for building The Swede Kit, including: - A list of resistors with quantities and values needed - A list of capacitors with quantities, values, and identification codes needed - A list of diodes, ICs, transistors, potentiometers, and other hardware included in the kit - Instructions for differentiating resistor and capacitor values and notes on preparing potentiometers - Diagrams showing foot switch solder lug designations and instructions for wiring the foot switch The checklist contains all the electronic components, hardware, and basic instructions required to construct the effect pedal circuit called The Swede from a build-it-yourself kit.

Uploaded by

Alex Arm.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Parts Checklist for The Swede Kit

Resistors:
1 - 22 Ohm (Red/Red/Black/Gold/Brown)
1 - 120 Ohm (Brown/Red/Black/Black/Brown)
1 - 150 Ohm (Brown/Green/Black/Black/Brown)
4 - 330 Ohm (Orange/Orange/Black/Black/Brown)
2 - 1k (Brown/Brown/Black/Brown/Brown)
2 - 3k3 (Orange/Orange/Black/Brown/Brown)
1 - 4k7 (Yellow/Purple/Black/Brown/Brown)
10 - 10k (Brown/Black/Black/Red/Brown)
2 - 22k (Red/Red/Black/Red/Brown)
1 - 47k (Yellow/Purple/Black/Red/Brown)
2 - 68k (Blue/Gray/Black/Red/Brown)
1 - 82k (Gray/Red/Black/Red/Brown)
5 - 100k (Brown/Black/Black/Orange/Brown)
1 - 220k (Red/Red/Black/Orange/Brown)
3 - 470k (Yellow/Purple/Black/Orange/Brown)
1 - 1M (Brown/Black/Black/Yellow/Brown)

Visit www.byocelectronics.com/resistorcodes.pdf for more information on how to


differentiate resistors.

Capacitors:
1 - 1n0 Film Cap (may say “102” on the body)
1 - 4n7 Film Cap (may say “472” on the body)
1 - 6n8 Film Cap (may say “682” on the body)
5 - 47n film Cap (may say “473” on the body)
1 - 68n Film Cap (may say “683” on the body)
1 - 100n Film Cap (may say “104” on the body)
1 - 150n film Cap (may say “154” on the body)
3 - 100pf Ceramic (101)
1 - 470pf Ceramic (471)
1 - 1.5uf Aluminum Electrolytic
3 - 1uf Aluminum Electrolytic
3 - 10uf Aluminum Electrolytic
1 - 47uf Aluminum Electrolytic
1 - 100uf Aluminum Electrolytic

Visit www.byocelectronics.com/capcodes.pdf for more info on how to differentiate


capacitors.

Diodes:
1 - 1N4001 diodes
5 - 1n4148 diodes
2 - Germanium Diodes (1N34A, 1N60, D9E, etc.)
IC's:
3 - SIP 8 socket
3 - M5218L Chips

Transistors:
2 - 2N3904
1 - 2N3906
1 - 2N5457

Potentiometers: SNAP OFF THE SMALL TABS ON THE TOP OF THE POTS OFF
WITH A PAIR OF NEEDLE NOSE PLIERS

1 - A10K (Volume)
2 - B10k (Low and High)
1 - C250k (Distortion) (PCB says ‘B250K’ use C taper instead)

Hardware:
1 - predrilled enclosure w/ 4 screws (optional)
1 - The Swede circuit board
1 - 3pdt footswitch
4 - knobs (optional)
1 - AC adaptor jack
1 - ¼”stereo jack
1 - ¼” mono jack
1 - battery snap
1 - LED
4 – rubber bumpers
2 – lock washers (for in and out jacks)
hook-up wire
FOOT SWITCH SOLDER LUG DESIGNATIONS

Step 3: Wiring the foot switch.


• Make a jumper between lugs 3 & 6 from clippings from the resistors.
Simply use your needle nose pliers to bend a piece of clipping into a U
shape & insert into lugs 3 & 6, then solder.

You might also like