Scribd
Upload
122 views

Sample Revision Test Oct 2010

This document contains a 20 question sample revision test for a CI 150 Geotechnics course covering topics in year 1 geology, year 1 soil mechanics, and year 2 soil mechanics. The test contains multiple choice and short answer questions testing knowledge of topics like chemical weathering conditions, slope failures, soil transport and properties, geotechnical site investigations, soil strength testing methods, consolidation, permeability, bearing capacity, and soil behavior under loading. It also includes several figures illustrating soil mechanics concepts to which some questions refer. The test is designed to take 1 hour to complete and questions are assigned equal marks of 5 points each.

Uploaded by

Karn Shah
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
122 views

Sample Revision Test Oct 2010

This document contains a 20 question sample revision test for a CI 150 Geotechnics course covering topics in year 1 geology, year 1 soil mechanics, and year 2 soil mechanics. The test contains multiple choice and short answer questions testing knowledge of topics like chemical weathering conditions, slope failures, soil transport and properties, geotechnical site investigations, soil strength testing methods, consolidation, permeability, bearing capacity, and soil behavior under loading. It also includes several figures illustrating soil mechanics concepts to which some questions refer. The test is designed to take 1 hour to complete and questions are assigned equal marks of 5 points each.

Uploaded by

Karn Shah
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

CI 150 Geotechnics

Sample Revision Test

2010

Please answer all questions.


Each question is assigned equal marks. (5 marks per question)
Time allocated 1 hour

Part I: Year 1 Geology

1) Under what climatic conditions does chemical weathering predominate?

2) What type of slope failure would you expect where bedding daylights (dips
out of a slope)?

3) How does transport distance influence the characteristics of transported


soils?

4) What are the main stages involved in a geotechnical site investigation?

5) What problems would you expect in a deep foundation excavation in black


shale?

Part 2: Year 1 Soil Mechanics

6) Give 3 examples of cases where raft foundations would be used.

7) Sketch the variation in horizontal pressure acting against the retaining wall
illustrated in Figure 1.

8) Define the following terms :


i. Water content (w)
ii. Degree of saturation (Sr)

9) Explain the difference between the terms “compaction” and “consolidation”?

10) Explain the terms plastic limit and liquid limit. How would you determine the
plastic and liquid limit for a soil?
Part 3 Year 2 Soil Mechanics

11. List two advantages of using the triaxial apparatus instead of the direct shear
box when testing to establish soil strength and stiffness.

12. Figure 2 below gives the axes for plotting a Mohr’s circle for a triaxial test,
the Mohr-Coulomb failure envelope is also included. Plot a Mohr’s circle for
a stress state where the soil is just about to fail in shear.

13. Figure 3 below gives a plot of specific volume (v) against the natural
logarithm of the mean stress (ln p’) for an idealized soil undergoing isotropic
compression and swelling. Clearly indicate on this diagram which is the
normal compression line and which is the swelling line.

14. Define the overconsolidation ratio for a soil subject to one-dimensional


compression in an oedometer, explaining all terms used.

15. Write down the equation for Darcy’s law as commonly used in soil mechanics,
explaining all terms.

16. Figure 4 below gives a flownet for flow through a dam. If the permeability
of the dam is 10-8 m/s, what is the rate of flow through the dam in m3/s. The
Nf
equation q = kH may be of use to you.
Nd

17. One of the requirements for the theoretical solution is that the deformation be
compatible. What is meant by a “compatible deformation.”

18. Consider the vertical cut illustrated in Figure 5 below. In undrained


conditions, failure is assumed to occur along a planar failure plane inclined at
45o to the horizontal, as indicated, and at failure the shear stress along this
plane, τ, equals the undrained shear strength su (Tresca failure criterion).
Using limit equilibrium, derive an expression for the minimum depth of cut,
H, that will just induce failure. Take the saturated unit weight of the soil to be
γ.

19. Figure 6 below gives a scenario that can be considered when applying the
limit equilibrium method to determine the undrained bearing capacity of a
shallow foundation. The failure plane is assumed to be the arc of a circle
centred at point 0. The limit equilibrium method can be applied by
considering moment equilibrium about the point 0. Using this approach write
down an expression for the maximum load the foundation can carry, Q, in
terms of B, α and su.

20. Figure 7 below gives a load displacement curve for a typical shallow
foundation. Indicate on this plot the region where the soil is behaviour is
elastic, where the soil behaviour is elasto-plastic and where the soil behaviour
is plastic.
Figure 1: Question 7

Excavated Soil

Figure 2 Question 12

φ’
σ’
Figure 3 Question 13

ln p’

Figure 4 Question 16

Water surface in reservoir

7m
Figure 5

W
W 2
H W
τ=su
45o
W
45o 2

Figure 6

Q
O
2α

su
Figure 7 Question 20

Load

Displacement

You might also like