Units system: SI 60006-POS-CAL-SF-No8-B7-BG-H250x250-R0

60006-POS-CAL-SF-No8-B7-BG-H250x250-R0
RAM Connection Standalone CE
Units system: s
Current Date: s
60006-POS-CAL-SF-No8-B7-BG-H250x250-R0
 60006-POS-CAL-SF-No8-B7-BG-H250x250-R0

Units system: SI

Steel connections
Joints summary
___________________________________________________________________________________________________________________________

Joint types:
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Joint Member 1 Member 2 Member 3 Braces/Branches
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
BCF Beam Column -- --
BCW Beam Column -- --
BG Beam Girder -- --
BS Left beam Right beam -- --
CS Top column Bottom column -- --
CC Column Continuous beam -- --
CBB Column Right beam Left beam 1 brace mandatory
CVR Beam -- -- 1 brace mandatory
VXB -- -- -- All braces mandatory
CB Column -- -- --
HCBB Column Front beam Right beam 1 brace mandatory
HBBB Girder Beam -- 1 brace mandatory
HXB -- -- -- All braces mandatory
CHB Chord -- -- 1 branch mandatory
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

__________________________________________________________________________________________________________________

Joint : 1 - BG ()
Design status : With warnings
__________________________________________________________________________________________________________________

Ratio : 0.77
Template(s) : SP BG

Member Section Material

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Beam H250X250 A36
Girder H250X250 A36
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page1
 60006-POS-CAL-SF-No8-B7-BG-H250x250-R0

Units system: SI

Steel connections
Loads summary
___________________________________________________________________________________________________________________________

Joint types:
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Joint Member 1 Member 2 Member 3 Braces/Branches
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
BCF Beam Column -- --
BCW Beam Column -- --
BG Beam Girder -- --
BS Left beam Right beam -- --
CS Top column Bottom column -- --
CC Column Continuous beam -- --
CBB Column Right beam Left beam 1 brace mandatory
CVR Beam -- -- 1 brace mandatory
VXB -- -- -- All braces mandatory
CB Column -- -- --
HCBB Column Front beam Right beam 1 brace mandatory
HBBB Girder Beam -- 1 brace mandatory
HXB -- -- -- All braces mandatory
CHB Chord -- -- 1 branch mandatory
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

__________________________________________________________________________________________________________________

Joint : 1 - BG ()
Design status : With warnings
__________________________________________________________________________________________________________________

Ratio : 0.77
Template(s) : SP BG

Member Condition V2 M33 M22 Axial MMax MLT

[KN] [KN*m] [KN*m] [KN] [KN*m]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Beam CB1 41.00 0.00 0.00 15.00 0.00 0.00
Left beam CB1 0.00 -- -- -- -- --
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Beam CB2 41.00 0.00 0.00 -15.00 0.00 0.00
Left beam CB2 0.00 -- -- -- -- --
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Beam CB3 -41.00 0.00 0.00 15.00 0.00 0.00
Left beam CB3 0.00 -- -- -- -- --
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Beam CB4 -41.00 0.00 0.00 -15.00 0.00 0.00
Left beam CB4 0.00 -- -- -- -- --
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page1
 60006-POS-CAL-SF-No8-B7-BG-H250x250-R0

Units system: SI

Steel connections
Detailed report
___________________________________________________________________________________________________________________________

___________________________________________________________________________________________________________________________

Connection name : SP BG
Connection ID : 1V
___________________________________________________________________________________________________________________________

Family: Beam - Girder (BG)

Type: Single plate
GENERAL INFORMATION
Connector

MEMBERS
Beam
General
Beam section : H250X250
Beam material : A36
sb: Beam setback : 15 mm
Beam edge inside support flanges : No
Beam to girder alignment : Top
Horizontal angle (deg) : 0
Vertical angle (deg) : 0
Coped
dct: Top cope depth : 0 mm
ct: Top cope length : 0 mm
dcb: Bottom cope depth : 0 mm
cb: Bottom cope length : 0 mm
Girder
General
Girder section : H250X250
Girder material : A36

SINGLE PLATE
Connector
Section : PL 16x110x190
b: Width : 110 mm
L: Length : 190 mm
Plate type : Extended
tp: Plate thickness : 16 mm
Material : A36
Plate position on beam : Center
Bolts : M24 A325M
nr: Bolt rows : 2
nc: Bolt columns : 1
nc: Bolt columns : 1
s: Pitch - longitudinal center-to-center spacing : 100 mm
Lev: Vertical edge distance : 45 mm
Leh: Horizontal edge distance : 45 mm
a: Distance between weld and bolts : 65 mm
Hole type on plate : Standard (STD)
Hole type on beam : Standard (STD)

Page1
 60006-POS-CAL-SF-No8-B7-BG-H250x250-R0
Weld : E70XX
D: Weld size (1/16 in) : 4
Wo: Obtuse side weld size (AWS) (1/16 in) : 4
Wa: Acute side weld size (AWS) (1/16 in) : 4
Wo: Obtuse side weld size (AISC) (1/16 in) : 4
Wa: Acute side weld size (AISC) (1/16 in) : 4

Design code: AISC 360-05 LRFD

DEMANDS
Description Ru Pu Load type
[KN] [KN]
--------------------------------------------------------------------------------------------------------------------------------------------------
CB1 41.00 15.00 Design
CB2 41.00 -15.00 Design
CB3 -41.00 15.00 Design
CB4 -41.00 -15.00 Design
--------------------------------------------------------------------------------------------------------------------------------------------------

GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References

Plate (beam side)

Vertical edge distance [mm] 45.00 41.65 -- Tables J3.4,
J3.5
Lemin = edmin + C2
= 41.65[mm] + 0[mm]
= 41.65[mm] Tables J3.4,
J3.5

Horizontal edge distance [mm] 45.00 41.65 -- Tables J3.4,

J3.5
Lemin = edmin + C2
= 41.65[mm] + 0[mm]
= 41.65[mm] Tables J3.4,
J3.5

Vertical center-to-center spacing (pitch) [mm] 100.00 64.00 216.00 Sec. J3.3,
Sec. J3.5
smin = 8/3*d
= 8/3*24[mm]
= 64[mm] Sec. J3.3

IsCorrosionConsidered ® False

smax = min(24*tp, 12 [in])

= min(24*9[mm], 12 [in])
= 216[mm] Sec. J3.5

Beam
Vertical edge distance [mm] 75.00 41.65 -- Tables J3.4,
J3.5
Lemin = edmin + C2
= 41.65[mm] + 0[mm]
= 41.65[mm] Tables J3.4,
J3.5

Horizontal edge distance [mm] 50.00 41.65 -- Tables J3.4,

J3.5
Lemin = edmin + C2
= 41.65[mm] + 0[mm]
= 41.65[mm] Tables J3.4,
J3.5

Page2
 60006-POS-CAL-SF-No8-B7-BG-H250x250-R0
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References

Support
Weld size [1/16in] 4 7 -- p. 10-101
wmin = (5/8)*tp
= (5/8)*16[mm]
= 10[mm] p. 10-101

DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References

Plate (beam side)

Bolts shear [KN] 56.83 43.66 CB1 0.77 Tables (7-1..14)
(n>=10) and (n<=12) and (IsStandardHole) ® (2>=10) and (2<=12) and (True) ® False

BoltFactor = 1 p. 10-102

fRn = f*Fnv*Ab
= 0.75*330.95[N/mm2]*452[mm2]
= 112.19[kN] Eq. J3-1

fRn = C*fRn*BoltFactor
= 0.507*112.19[kN]*1
= 56.83[kN] Tables (7-1..14)

Flexure with the Von-Mises shear reduction [KN*m] 32.08 7.61 CB1 0.24 p. 10-103
Ag = Lp*tp
= 190[mm]*16[mm]
= 3040[mm2] Sec. D3-1

fv = V/Ag
= 41[kN]/3040[mm2]
= 13.49[N/mm2] p. 10-103
2 2 1/2
fFcr = (max(0, (f*Fy) - 3*fv ))
2 2 1/2
= (max(0, (0.9*248.21[N/mm2]) - 3*13.49[N/mm2] ))
= 222.16[N/mm2] p. 10-103
2
Zx = tp*L /4
2
= 16[mm]*190[mm] /4
= 1.44E+05[mm3] T. 17-27

fMn = fFcr*Z
= 222.16[N/mm2]*1.44E+05[mm3]
= 32.08[kN*m] p. 10-103

Bolt bearing under shear load [KN] 93.94 41.00 CB1 0.44 Eq. J3-6,
p. 7-18
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 45[mm] - 25.59[mm]/2)
= 32.21[mm] Sec. J3.10

Lc-spa = Max(0.0, s - dh)

= Max(0.0, 100[mm] - 25.59[mm])
= 74.41[mm] Sec. J3.10

Page3
 60006-POS-CAL-SF-No8-B7-BG-H250x250-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References

rn1 = min(k1*Lc-end*tp*Fu, k2*d*tp*Fu)

= min(1.2*32.21[mm]*16[mm]*399.89[N/mm2], 2.4*24[mm]*16[mm]*399.89[N/mm2])
= 247.28[kN] Eq. J3-6

rn2 = min(k1*Lc-spa*tp*Fu, k2*d*tp*Fu)

= min(1.2*74.41[mm]*16[mm]*399.89[N/mm2], 2.4*24[mm]*16[mm]*399.89[N/mm2])
= 368.54[kN] Eq. J3-6

fRn = f*C*min(rn1, rn2)

= 0.75*0.507*min(247.28[kN], 368.54[kN])
= 93.94[kN] p. 7-18

Shear yielding [KN] 452.74 41.00 CB1 0.09 Eq. J4-3

Ag = Lp*tp
= 190[mm]*16[mm]
= 3040[mm2] Sec. D3-1

fRn = f*0.60*Fy*Ag
= 1*0.60*248.21[N/mm2]*3040[mm2]
= 452.74[kN] Eq. J4-3

Shear rupture [KN] 390.57 41.00 CB1 0.10 Eq. J4-4

Lh = dh + 1/16 [in]
= 25.59[mm] + 1/16 [in]
= 27.18[mm] Sec. D3-2

Le = L - n*Lh
= 190[mm] - 2*27.18[mm]
= 135.65[mm] DG4 Eq. 3-13

Anv = Le*tp
= 135.65[mm]*16[mm]
= 2170.4[mm2] Sec. J4-2

fRn = f*0.60*Fu*Anv
= 0.75*0.60*399.89[N/mm2]*2170.4[mm2]
= 390.57[kN] Eq. J4-4

Block shear [KN] 409.87 41.00 CB1 0.10 Eq. J4-5

dhh = dh + 1/16 [in]
= 25.59[mm] + 1/16 [in]
= 27.18[mm] Sec. D3-2

dhv = dh + 1/16 [in]

= 25.59[mm] + 1/16 [in]
= 27.18[mm] Sec. D3-2

Ant = (Leh + (nc - 1)*spa - (nc - 0.5)*dhh)*tp

= (45[mm] + (1 - 1)*80[mm] - (1 - 0.5)*27.18[mm])*16[mm]
= 502.6[mm2] Sec. J4-3

Agv = (Lev + (n - 1)*s)*tp

= (45[mm] + (2 - 1)*100[mm])*16[mm]
= 2320[mm2] Sec. J4-3

Page4
 60006-POS-CAL-SF-No8-B7-BG-H250x250-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References

Anv = (Lev + (n - 1)*(s - dhv) - dhv/2)*tp

= (45[mm] + (2 - 1)*(100[mm] - 27.18[mm]) - 27.18[mm]/2)*16[mm]
= 1667.8[mm2] Sec. J4-3

IsStressUniform ® True

Ubs = 1 Sec. J4-3

fRn = f*min(0.6*Fu*Anv + Ubs*Fu*Ant, 0.6*Fy*Agv + Ubs*Fu*Ant)

= 0.75*min(0.6*399.89[N/mm2]*1667.8[mm2] + 1*399.89[N/mm2]*502.6[mm2], 0.6*248.21[N/mm2]*2320[mm2] + 1*
399.89[N/mm2]*502.6[mm2])
= 409.87[kN] Eq. J4-5

Flexural rupture [KN] 177.97 41.00 CB1 0.23 p. 9-6

Lh = dh + 1/16 [in]
= 25.59[mm] + 1/16 [in]
= 27.18[mm] Sec. D3-2
2 2 2
Znet = tp/4*(L - s *n*(n - 1)*Lh/L)
2 2 2
= 16[mm]/4*(190[mm] - 100[mm] *2*(2 - 1)*27.18[mm]/190[mm])
= 1.10E+05[mm3] [4]

fRn = f*Fu*Znet/e
= 0.75*399.89[N/mm2]*1.10E+05[mm3]/185.5[mm]
= 177.97[kN] p. 9-6

Bolt bearing under axial load [KN] 93.94 15.00 CB1 0.16 Eq. J3-6,
p. 7-18
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 45[mm] - 25.59[mm]/2)
= 32.21[mm] Sec. J3.10

Lc-spa = Max(0.0, s - dh)

= Max(0.0, 80[mm] - 25.59[mm])
= 54.41[mm] Sec. J3.10

rn1 = min(k1*Lc-end*tp*Fu, k2*d*tp*Fu)

= min(1.2*32.21[mm]*16[mm]*399.89[N/mm2], 2.4*24[mm]*16[mm]*399.89[N/mm2])
= 247.28[kN] Eq. J3-6

rn2 = min(k1*Lc-spa*tp*Fu, k2*d*tp*Fu)

= min(1.2*54.41[mm]*16[mm]*399.89[N/mm2], 2.4*24[mm]*16[mm]*399.89[N/mm2])
= 368.54[kN] Eq. J3-6

fRn = f*C*min(rn1, rn2)

= 0.75*0.507*min(247.28[kN], 368.54[kN])
= 93.94[kN] p. 7-18

Tension yielding [KN] 679.10 15.00 CB1 0.02 Eq. J4-1

fRn = f*Fy*Ag
= 0.9*248.21[N/mm2]*3040[mm2]
= 679.1[kN] Eq. J4-1

Tension rupture [KN] 650.95 15.00 CB1 0.02 Eq. J4-2

Ag = Lp*tp
= 190[mm]*16[mm]
= 3040[mm2] Sec. D3-1

Page5
 60006-POS-CAL-SF-No8-B7-BG-H250x250-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References

IsBoltedConnection ® True

Lh = dh + 1/16 [in]
= 25.59[mm] + 1/16 [in]
= 27.18[mm] Sec. D3-2

An = (l - n*Lh)*tp
= (190[mm] - 2*27.18[mm])*16[mm]
= 2170.4[mm2] Sec. D3-2

Ae = min(0.85*Ag, An)
= min(0.85*3040[mm2], 2170.4[mm2])
= 2170.4[mm2] Sec. J4-1

fRn = f*Fu*Ae
= 0.75*399.89[N/mm2]*2170.4[mm2]
= 650.95[kN] Eq. J4-2

Tear out under axial load [KN] 510.31 15.00 CB1 0.03 Eq. J4-5
dhh = dh + 1/16 [in]
= 25.59[mm] + 1/16 [in]
= 27.18[mm] Sec. D3-2

dhv = dh + 1/16 [in]

= 25.59[mm] + 1/16 [in]
= 27.18[mm] Sec. D3-2

n>1 ® 2>1 ® True

Agv = 2*(L + (nc - 1)*g)*tp

= 2*(45[mm] + (1 - 1)*80[mm])*16[mm]
= 1440[mm2] Sec. J4-3

Anv = 2*(L + (nc - 1)*g - dhh*(nc - 0.5))*tp

= 2*(45[mm] + (1 - 1)*80[mm] - 27.18[mm]*(1 - 0.5))*16[mm]
= 1005.2[mm2] Sec. J4-3

Ant = (s - dhv)*(n - 1)*tp

= (100[mm] - 27.18[mm])*(2 - 1)*16[mm]
= 1165.2[mm2] Sec. J4-3

IsStressUniform ® True

Ubs = 1 Sec. J4-3

fRn = f*min(0.6*Fu*Anv + Ubs*Fu*Ant, 0.6*Fy*Agv + Ubs*Fu*Ant)

= 0.75*min(0.6*399.89[N/mm2]*1005.2[mm2] + 1*399.89[N/mm2]*1165.2[mm2], 0.6*248.21[N/mm2]*1440[mm2] + 1*
399.89[N/mm2]*1165.2[mm2])
= 510.31[kN] Eq. J4-5

Plate (support side)

Weld capacity [KN] 476.58 43.66 CB1 0.09 Tables 8-4 .. 8-11
e=0 p. 10-135

fRn = 2 * (f*C*C1*D*L)
= 2 * (0.75*0.358[kN/mm]*1*4*222[mm])
= 476.58[kN] Tables 8-4 .. 8-11

Page6
 60006-POS-CAL-SF-No8-B7-BG-H250x250-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References

Beam
Bolt bearing under shear load [KN] 78.75 41.00 CB1 0.52 Eq. J3-6,
p. 7-18
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 75[mm] - 25.59[mm]/2)
= 62.21[mm] Sec. J3.10

Lc-spa = Max(0.0, s - dh)

= Max(0.0, 100[mm] - 25.59[mm])
= 74.41[mm] Sec. J3.10

rn1 = min(k1*Lc-end*tp*Fu, k2*d*tp*Fu)

= min(1.2*62.21[mm]*9[mm]*399.89[N/mm2], 2.4*24[mm]*9[mm]*399.89[N/mm2])
= 207.3[kN] Eq. J3-6

rn2 = min(k1*Lc-spa*tp*Fu, k2*d*tp*Fu)

= min(1.2*74.41[mm]*9[mm]*399.89[N/mm2], 2.4*24[mm]*9[mm]*399.89[N/mm2])
= 207.3[kN] Eq. J3-6

fRn = f*C*min(rn1, rn2)

= 0.75*0.507*min(207.3[kN], 207.3[kN])
= 78.75[kN] p. 7-18

Shear yielding [KN] 335.08 41.00 CB1 0.12 Eq. J4-3

Ag = Lp*tp
= 250[mm]*9[mm]
= 2250[mm2] Sec. D3-1

fRn = f*0.60*Fy*Ag
= 1*0.60*248.21[N/mm2]*2250[mm2]
= 335.08[kN] Eq. J4-3

Bolt bearing under axial load [KN] 241.03 15.00 CB1 0.06 Eq. J3-6
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 50[mm] - 25.59[mm]/2)
= 37.21[mm] Sec. J3.10

fRn = f*(min(k1*Lc-end, k2*d))*tp*Fu*nc

= 0.75*(min(1.2*37.21[mm], 2.4*24[mm]))*9[mm]*399.89[N/mm2]*2
= 241.03[kN] Eq. J3-6

Yielding strength due to axial load [KN] 2042.45 15.00 CB1 0.01 Eq. D2-1
fRn = f*Fy*Ag
= 0.9*248.21[N/mm2]*9143[mm2]
= 2042.45[kN] Eq. D2-1

Tension rupture [KN] 1320.53 15.00 CB1 0.01 Eq. J4-2

IsBoltedConnection ® True

Lh = dh + 1/16 [in]
= 25.59[mm] + 1/16 [in]
= 27.18[mm] Sec. D3-2

An = Ag - nh*tp*Lh
= 9143[mm2] - 2*9[mm]*27.18[mm]
= 8653.85[mm2] Sec. D3-2

Page7
 60006-POS-CAL-SF-No8-B7-BG-H250x250-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References

U = 1 - x/l
= 1 - 49.12[mm]/100[mm]
= 0.509 Table D3.1

Ae = U*An
= 0.509*8653.85[mm2]
= 4402.95[mm2] Sec. D3-3

fRn = f*Fu*Ae
= 0.75*399.89[N/mm2]*4402.95[mm2]
= 1320.53[kN] Eq. J4-2

Tear out under axial load [KN] 297.10 15.00 CB1 0.05 Eq. J4-5
dhh = dh + 1/16 [in]
= 25.59[mm] + 1/16 [in]
= 27.18[mm] Sec. D3-2

dhv = dh + 1/16 [in]

= 25.59[mm] + 1/16 [in]
= 27.18[mm] Sec. D3-2

n>1 ® 2>1 ® True

Agv = 2*(L + (nc - 1)*g)*tp

= 2*(50[mm] + (1 - 1)*80[mm])*9[mm]
= 900[mm2] Sec. J4-3

Anv = 2*(L + (nc - 1)*g - dhh*(nc - 0.5))*tp

= 2*(50[mm] + (1 - 1)*80[mm] - 27.18[mm]*(1 - 0.5))*9[mm]
= 655.43[mm2] Sec. J4-3

Ant = (s - dhv)*(n - 1)*tp

= (100[mm] - 27.18[mm])*(2 - 1)*9[mm]
= 655.43[mm2] Sec. J4-3

IsStressUniform ® True

Ubs = 1 Sec. J4-3

fRn = f*min(0.6*Fu*Anv + Ubs*Fu*Ant, 0.6*Fy*Agv + Ubs*Fu*Ant)

= 0.75*min(0.6*399.89[N/mm2]*655.43[mm2] + 1*399.89[N/mm2]*655.43[mm2], 0.6*248.21[N/mm2]*900[mm2] + 1*
399.89[N/mm2]*655.43[mm2])
= 297.1[kN] Eq. J4-5

Support
Welds rupture [KN/m] 2159.43 119.11 CB1 0.06 p. 9-5
Rn = 0.6*Fu*tp
= 0.6*399.89[N/mm2]*9[mm]
= 2.16[kN/mm] p. 9-5

e=0 p. 10-135

Dmin = P/(f*C*C1*L)
= 21.83[kN]/(0.75*0.358[kN/mm]*1*222[mm])
= 0.366 tables 8-4..11

HasWeldsOnBothSides ® False

Page8
 60006-POS-CAL-SF-No8-B7-BG-H250x250-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References

1/2
Ru = 0.6*FEXX*(2) /2*Dmin/16 [in]
1/2
= 0.6*482.63[N/mm2]*(2) /2*0.366/16 [in]
= 0.119[kN/mm] p. 9-5

Global critical strength ratio 0.77

NOTATION
Ab: Nominal bolt area
Ae: Effective net area
Ag: Gross area
Agv: Gross area subject to shear
An: Net area
Ant: Net area subject to tension
Anv: Net area subjected to shear
fRn: Available shear strength per bolt
BoltFactor: Bolt capacity factor
C: Bolt group coefficient
c: Coped length
C1: Electrode strength coefficient
C2: Edge distance increment
C: Weld group coefficient
d: Nominal bolt diameter
dh: Nominal hole dimension
dhh: Horizontal hole dimension
dhv: Vertical hole dimension
D: Number of sixteenths of an inch in the weld size
Dmin: Number of sixteenths of an inch in the minimum weld size
e: Load eccentricity
FEXX: Electrode classification number
Fnv: Nominal shear stress
Fu: Specified minimum tensile strength
fv : Required shear stress
Fy: Specified minimum yield stress
g: Transversal gage between bolts
ho: Reduced beam depth
HasWeldsOnBothSides: Has welds on both sides
IsBoltedConnection: Is bolted connection
IsCorrosionConsidered: Is corrosion considered
IsStandardHole: Is standard hole (STD)
IsStressUniform: Is the stress uniform
k1: Bearing factor
k2: Bearing factor
l: Length
L: Length
Lc-end: Clear distance
Le: Effective length
Le: Edge distance
Leh: Horizontal edge distance
Lemin: Minimum edge distance
Lev: Vertical edge distance
Lh: Hole dimension for tension and shear net area
Lp: Plate length
L: Length of weld
l: Slenderness
edmin: Minimum edge distance
n: Bolts rows number
nc: Number of bolt columns
nh: Holes number
P: Required axial force
f: Design factors
fFcr: Design or allowable flexural stress buckling
fMn: Design or allowable strength
fRn: Design or allowable strength

Page9
 60006-POS-CAL-SF-No8-B7-BG-H250x250-R0
NOTATION
Rn: Nominal strength
rn1: Nominal strength of one bolt
rn2: Nominal strength of one bolt
Ru: Required strength
smax: Maximum spacing
smin: Minimum spacing
spa: Transversal spacing between bolts or welds
s: Longitudinal bolt spacing
Lc-spa: Distance between adjacent holes edges
tp: Thickness of the connected material
tp: Plate thickness
tw: Web thickness
U: Shear lag factor
Ubs: Stress index
V: Shear load
wmin: Minimum weld size required
x: Connection eccentricity
Z: Plastic modulus
Znet: Net plastic section modulus
Zx : Plastic section modulus about the x-axis

REFERENCES
[4] AISC 2005, Design Examples Version 13.0, pp. IIA-63, IIA_86, IIA-98

Page10
 60006-POS-CAL-SF-No8-B7-BG-H250x250-R0

Units system: SI

Steel connections
Connections elements summary
___________________________________________________________________________________________________________________________

CONNECTION ELEMENTS

Plates
ID Plate Material Length Width Thickness Qty.
[mm] [mm] [mm]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
P0 PL 16x110x190 A36 190.00 230.50 16.00 1
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Bolts
ID Bolt Grade Length Diameter Qty.
[mm] [mm]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
B0 M24 A325M G8_8 25.00 24.00 2
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Welds
ID Weld Type Strength Size Length
[KN/mm2] [mm]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
W0 E70XX Fillet 0.48 6[mm] 926.00
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

CONNECTION ELEMENTS PER JOINT

Type, Family : Shear connection, BG

Connection : 1V
___________________________________________________________________________________________________________________________

Element Description ID
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Right side
Bolts - Beam side M24 A325M B0
Plate - Support side PL 16x110x190 P0
Weld - Support side E70XX W0
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Notes

Joint type:
BG : Beam - Girder

Connector type:
SP : Single plate

Page1