Bar Properties

DYWI® Drill Hollow Bar DYWIDAG

THREADBAR®

DYWIDAG THREADBAR® Reinforcing Steel ASTM A615 (Grade 75 & 80)

Maximum Minimum Nominal Minimum
THREADBAR®
THREADBAR® Yield Stress Cross Section Area Yield Load Nominal Weight
Designation
Diameter (fy) (As) (fy x As)
[mm] [in] [mm] [ksi] [MPa] [in²] [mm²] [kips] [kN] [lbs/ft] [kg/m]
#6 19 0.86 22 75 517 0.44 284 33.0 147 1.50 2.23
#7 22 0.99 25 75 517 0.60 387 45.0 200 2.04 3.04
#8 25 1.12 28 75 517 0.79 510 59.3 264 2.67 3.97
#9 29 1.26 32 75 517 1.00 645 75.0 334 3.40 5.06
#10 32 1.43 36 75 517 1.27 819 95.3 424 4.30 6.40
#11 36 1.61 41 75 517 1.56 1,006 117.0 520 5.31 7.90
#14 43 1.86 47 80 552 2.25 1,452 180.0 801 7.65 11.38
#18 57 2.50 64 80 552 4.00 2,581 320.0 1,423 13.60 20.24
#20 63 2.72 69 80 552 4.91 3,168 393.0 1,748 16.70 24.85
#24 75 3.18 81 75 517 7.06 4,555 529.5 2,355 24.09 35.85
#28 90 3.68 94 75 517 9.62 6,207 721.5 3,209 32.79 48.80
Note: Maximum allowable temporary tension is 90% of yield load. Mill length is 60 ft (#6 through #24) and 53 ft for #28.

DYWIDAG THREADBAR® Reinforcing Steel ASTM A615 (Grade 100)

Maximum Minimum Nominal Minimum

THREADBAR®
THREADBAR® Yield Stress Cross Section Area Yield Load Nominal Weight
Designation
Diameter (fy) (As) (fy x As)

[mm] [in] [mm] [ksi] [MPa] [in2] [mm2] [kips] [kN] [lbs/ft] [kg/m]
#6 19 0.86 22 100 690 0.44 284 44.0 196 1.50 2.23
#7 22 0.99 25 100 690 0.60 387 60.0 267 2.04 3.04
#8 25 1.12 28 100 690 0.79 510 79.0 351 2.67 3.97
#9 29 1.26 32 100 690 1.00 645 100.0 445 3.40 5.06
#10 32 1.43 36 100 690 1.27 819 127.0 565 4.30 6.40
#11 36 1.61 41 100 690 1.56 1,006 156.0 694 5.31 7.90
#14 43 1.86 47 100 690 2.25 1,452 225.0 1,001 7.65 11.38
#18 57 2.50 64 100 690 4.00 2,581 400.0 1,779 13.60 20.24
#20 63 2.72 69 100 690 4.91 3,168 491.0 2,184 16.70 24.85

DYWIDAG THREADBAR® Prestressing Steel ASTM A722 (Grade 150)

Maximum Minimum Ultimate Nominal Minimum Ultimate
THREADBAR®
THREADBAR® Tensile Strength Cross Section Area Tensile Load Nominal Weight
Designation
Diameter (fu) (As) (fu x As)
[in] [mm] [in] [mm] [ksi] [MPa] [in²] [mm²] [kips] [kN] [lbs/ft] [kg/m]
1" 26 1.25 32 150 1,034 0.85 548 127.5 567 3.01 4.48
1 ¼" 32 1.45 37 150 1,034 1.25 806 187.5 834 4.39 6.53
1⅜" 36 1.63 41 150 1,034 1.58 1,019 237.0 1,054 5.56 8.27
1 ¾" 46 2.01 51 155 1,069 2.58 1,665 400.0 1,779 9.23 13.73
2 ½" 65 2.80 71 150 1,034 5.16 3,329 774.0 3,443 18.20 27.08
3" 75 3.15 80 150 1,034 6.85 4,419 1,027.5 4,571 24.09 35.85
Note: Maximum allowable temporary test tension shall not exceed 80% of the Minimum Ultimate Tensile Load;
Mill length = 60'-0" for 1", 1¼" and 1 " Threadbars and 45'-0" for 1¾", 2½" and 3" bars.
WARNING: DO NOT WELD on or near A722 prestressing bars or their anchorages.

26
Hardware Properties

B
Anchor Nut H Hex Nut
A B/2 B/2

Bearing Washer

ØC
Wedge Washer Coupler Bevel Washers

ØW ØV
DYWIDAG nuts and couplers develop full load of the bar nominal ultimate load.

DYWIDAG THREADBAR® Reinforcing Steel Hardware Properties (Grade 75 & 80)

Hex Nut Coupler Coupler Maximum Angle Bevel Washer
THREADBAR®
Length Length Outer Diameter Compensation * Diameter
Designation
H B ØC ØV
[in] [mm] [in] [mm] [in] [mm] [degrees] [in] [mm]
#6 1.43 36 3.12 79 1.22 31 17 1.78 45
#7 1.71 43 3.73 95 1.41 36 19 2.26 57
#8 1.84 47 4.03 102 1.59 40 17 2.56 65
#9 2.30 58 5.02 128 1.79 46 18 2.88 73
#10 2.56 65 5.70 145 2.02 51 19 3.20 81
#11 2.89 73 6.37 162 2.25 57 18 3.27 83
#14 3.55 90 7.82 199 2.65 67 18 3.25 83
#18 4.23 107 9.35 238 3.50 89 18 4.00 102
#20 4.85 123 10.38 264 3.86 98
#24 4.10 104 9.19 233 4.75 121
#28 4.80 122 10.61 270 5.38 137
* using two washers in a set. Solutions for large bars and larger angles are available – please consult your local DSI Sales Engineer
Couplers and hex nuts develop the bar ultimate strength.

DYWIDAG THREADBAR® Reinforcing Steel Hardware Properties (Grade 100)

Hex Nut Coupler Coupler Maximum Angle Bevel Washer
THREADBAR®
Length Length Outer Diameter Compensation * Diameter
Designation
H B ØC ØV
[in] [mm] [in] [mm] [in] [mm] [degrees] [in] [mm]
#6 2.88 73 6.25 159 1.25 32 17 1.78 45
#7 3.13 79 7.00 178 1.50 38 19 2.26 57
#8 3.38 86 7.13 181 1.75 45 17 2.56 65
#9 3.50 89 7.25 184 1.88 48 18 2.88 73
#10 3.50 89 7.50 191 2.13 54 19 3.20 81
#11 3.88 98 8.00 203 2.38 60 18 3.27 83
#14 4.50 114 8.25 210 2.75 70 18 3.25 83
#18 5.25 133 10.50 267 3.63 92 18 4.00 102
#20 6.00 152 12.25 311 4.00 102
* using two washers in a set. Solutions for large bars and larger angles are available – please consult your local DSI Sales Engineer
Couplers and hex nuts develop the bar ultimate strength.

DYWIDAG THREADBAR® Prestressing Steel Hardware Properties (Grade 150)

Nut Coupler Coupler Maximum Angle Wedge Washer
THREADBAR®
Length Length Outer Diameter Compensation * Diameter
Designation
A/H B ØC ØW
[in] [in] [mm] [in] [mm] [in] [mm] [degrees] [in] [mm]
1" 2.36 / 2.63 60 / 67 6.25 159 2.00 51 20 4.55 116
1 ¼" 3.15 / 2.88 80 / 73 6.75 171 2.38 60 20 4.55 / 5.50 116 / 140
1⅜" 3.53 / 3.88 90 / 99 8.75 222 2.75 70 20 5.50 140
1 ¾" 3.50 / 4.00 89 / 101.6 6.80 172.7 3.⅛ 79.4 20 7.26 184
2 ½" – / 5.00 – / 127 10.75 273 4.50 114
3" – / 5.00 – / 127 11.00 279 5.25 133
* using two washers in a set. Solutions for large bars and larger angles are available – please consult your local DSI Sales Engineer
Couplers and hex nuts develop the bar ultimate tensile load.

27