Technical Data Sheet

PxW AC UPS System

> PEW 5 – 200 kVA single phase
> PDW 10 – 220 kVA three phase
> Higher ratings on request
Technical data PEW single phase / PDW three phase

UPS input Rectifier input voltage 3x380 / 400 / 415V

Voltage tolerance
DC in tolerance +/-10 %
for function +10 / -15 %
Bypass input voltage single phase 1x220 / 230 / 240V + / -10 %
three phase 3x380 / 400 / 415V + / -10 %
Frequency 50 / 60 Hz + / -6 %
Inrush current <10x IN (input current)

Intermediate DC circuit Voltage 110 / 125 / 220 / 400VDC

Rectifier voltage tolerance + / -1 % I-U characteristic
Float voltage range at -10 % line power 100 – 115 % programmable
Boost voltage range at nominal line power 100 – 125 % programmable
Boost charge time 1-24h programmable
Charging current limitation depending on battery, programmable
Inverter input range (Output tolerance + / -1 %) +20 / -15 %
Inverter maximum input range (Output tolerance + / -10 %) typical +/-25 %

UPS output Nominal UPS rating kVA at 0.8 lagging PF

Voltage single phase 1x 220 / 230 / 240V
three phase 3x380 / 400 / 415V
Voltage tolerance:
static within 0-100 % load +/-1 %
dynamic at 100 % load surge +/-4 %
regulation time < 25 ms
Overload:
Inverter 1 min 150 %
Inverter 10 min 125 %
Bypass 100 ms 1000 %
Short-circuit inverter 50 –100 ms 200 %
Frequency 50 (60) Hz
Frequency stability, free running < 0.01 %
Synchronization range 0.5 / 1 / 2 / 4 / 6 / 8 %
Slew rate single unit 0.25 / 0.5 / 1 / 2 / 4 Hz / s programmable
Slew rate redundant system 4.0 Hz / s
Wave form sinusoidal
Admissible output crest factor unlimited
Distortion factor:
Linear load ≤  3 %
Non-linear load according to IEC 62040-3 ≤  5 %
Allowable power factor 0.4 lag – 0.9 lead
Fault clearing capability 30 % of UPS nom. current rated gG fuse
(IEC 60269) within 10 ms and bypass available

General data Ambient temperature range for storage from -20 to +70 °C
Ambient temperature range for operation from -10 to +40 °C (100 % nominal load)
Altitude above sea level 1000 m without load de-rating
Allowable air humidity <95 % (non condensing)
Noise level standard n+1 fan system 60 – 70 dBA depending on type
Noise level 100 % redundant fans 65 – 75 dBA depending on type
Degree of protection IP20 according to IEC 60529
Paint pebble gray, RAL 7032 structured
Efficiency up to 93 % depending on type
Cooling forced ventilation with redundant n+1 ­monitored
fans
Standards:
Safety IEC / EN 62040-1
EMC IEC 62040-2, EN 50091-2
Performance IEC / EN 62040-3
UPS classification VFI-SS-111 acc. to IEC 62040-3
Conformity CE-Label

Data subject to changes

Technical Data SDC
Specification PEW single phase / PDW three phase

Typical single-line drawing  Options

Parallel redundant configuration

Other input voltages single phase 190 – 690V
three phase 190 – 690V
Other output voltages single phase 110 – 288V
three phase 190 – 690V
Frequency 60 Hz + / - 6 %
12-pulse Rectifier with isolation transformer
Oversized rectifier
Rectifier fuse
Bypass input switch or MCCB
Rectifier input MCCB
Single phase drawing Sensor for temperature dependent battery charging voltage,
recommended for sealed batteries and wide temperature range
Battery voltage & UPS ratings Battery temperature alarm
Diode for reverse polarity protection
Voltage (VDC) 110 125 220 400
Rectifier output isolator / circuit breaker
5 – 5 – 5 – – –
Battery fuse in UPS
10 10 10 10 10 10 – –
Battery fuse box
15 15 15 15 15 15 – – Battery MCCB box
20 20 20 20 20 20 – – Inverter input isolator / circuit breaker
40 40 40 40 40 40 – – Oversized inverter
UPS ratings (kVA)

– – – – 50 – – – Static Switch EA (Inverter side)

– 60 – 60 60 60 – – Battery Monitor (programmable battery data)
– 80 – 80 80 80 – – Battery asymmetry supervision
– – – – 100 100 – – AC and DC ground fault alarm
– – – – – 120 120 120 RS-232 / 485 interface (event log download)
150 RJ-45 Ethernet port for WEB browser based monitoring
– – – – – 160 – 160
RS-485 MODBUS Protocol (slave)
External time synchronization
– – – – – – 200 –
Top and / or bottom cable entry
– – – – – – – 220
Space heaters
Higher ratings and other voltages on request Ventilation 100 % redundant
■ single phase  ■ three phase Panel lighting
Ambient temperature maximum +55 °C
Standard configuration Allowable altitude up to 4000 m above sea level
Single UPS Protection up to IP52
UPS output voltage single phase 1x230V Other colors
three phase 3x400 / 230V Bypass isolation transformer
Rectifier input voltage 3x400V +10 / -10 % Bypass stabilizer with isolation transformer
Bypass input voltage single phase 1x230V +10 / -10 % Black start facility
three phase 3x400 / 230V +10 / -10 % Key switch on front panel
Frequency 50 Hz + / -6 %
Six-pulse Rectifier with isolation transformer Additional analog meters 96x96, cl. 1.5
Rectifier sized for output PF = 0.8 Set with VM DC, AM Bat & output FM, VM & AM
Rectifier input switch Set with Input VM & AM with select switch
Fixed charging voltage I-U characteristic kW of output
Static switch EN Bypass (line power side) with additional Power factor
backfeed protection
LC display unit with additional alarm LEDs Relay board A077, 16 fail-safe NO / NC contacts:
Alarm relays for battery operation and common alarm Rectifier line power fault Ground fault DC Inverter fuse blown
Bottom cable entry DC out of tolerance 5x options Bypass line power fault
Ground terminal Rectifier fuse blown Fan failure Power supply unit fault
N+1 monitored two-speed fans Battery discharged Overtemperature
Ambient temperature range from -10 to +40 °C
Protection IP20 Relay board A078, 16 fail-safe NO / NC contacts:
Painting pebble gray, RAL 7032 structured EA inhibited Battery disconnected Inverter ON
Battery MCCB in UPS EN inhibited Battery Boost charge operation
Manual Bypass Switch 3 pos in UPS Manual Bypass ON Rectifier failure Rectifier ON
Asynchronous EA ON External horn
Inverter fault EN ON Overload Inverter / Bypass

Additional options are available on request

Human-machine interface (front panel)

The front panel includes a comprehensive and flexible human-machine interface. It is divided into four sections:

The system panel shows the system’s current

state of operation (which part of the system is
currently supplying the load and which is in stand-
by mode). LEDs also indicate possible faults.

Operations for turning on and off the system and a

lamp test button for checking whether all LED indi-
cations are functioning properly. To shut down the
­system, you have to press the ON and OFF buttons
at the same time.

The display unit consists of an LC display, an

alarm LED, an acoustic alarm and a keypad. From
here, the user can set operational parameters,
obtain current measurement data, and access the
event and alarm logs.

On the alarm indication panel, the respective

LEDs light up to indicate a possible fault or after
an alarm has occurred.

Operational parameters

Selectable second display language

Auto start
Bypass operation
Boost charge
Auto boost (charge)
Battery capacity test
Battery monitor test (optional)
Set date / time

Measurements

Load in  % of nominal kVA rating

AC rectifier line power 1 voltage and current
AC bypass line power 2 voltage
DC total current, battery voltage and current
Battery temperature (with optional sensor)
AC Inverter current
AC output voltage, current and frequency
AC output peak current
Time left in battery operation with current load (optional with programmed battery data)
Event log with date and time (operating mode changes and alarms)

GUTOR Electronic LLC Offices

Hardstrasse 72 – 74 Brazil > Canada > China > Germany > India
5430 Wettingen Japan > Malaysia > Mexico > Russia > Saudi Arabia
Switzerland United Arab Emirates > USA
Q410.053 Rev. 1

P +41 (0)56 437 34 34

F +41 (0)56 437 34 44
[email protected]
www.gutor.com