Lenntech

[email protected] Tel. +31-152-610-900

MODEL SU-620

Membrane Type Cross Linked Polyamide Composite

Performance Specification
NaCl Solution MgSO4Solution
Salt Rejection 1,2 55.0 % 3 99.0 %4
Product Flow Rate 1,2 18.0 m3/day (4’760 gpd) 16.0 m3/day (4’230 gpd)6

Notes:
1
Test Conditions
Pressure 3.5 kg/cm2 (50 psi)
Temperature 25 °C ( 77 °F)
Feed Concentration 500 ppm as NaCl or MgSO
4
Brine Flow Rate 80 l/min (21.1 gpm)
Feed pH 6.5
2
Average value for 100 elements after 1 hour operation
3 4
45.0% minimum * 98.0% minimum
4 3 6
16 m /day (4’230 gpd) minimum * 14.0 m3/day (3’700 gpd) minimum
* For any single element

Dimensions:

Flow direction
22

F B

201 32 Permeate

F
B

11 11
1016

F Feed Water B Concentrated Brine All dimensions shown in millimeters

ROPUR AG continuously improves its products and reserves the right to change above specifications without prior notice. Our general terms of sales and warranty make integral part of these informations and cannot be disclaimed.
 Lenntech

Design Conditions
1
Recommended
Operating Pressure 2,3 < 10 kg/cm2 (143 psi)
Feedwater Temperature 4 < 35 °C (95 °F)
Feedwater Turbidity (SDI ) 2,5 <4
15
Feedwater Chlorine Concentration < 1 ppm
pH Range, Continuous Operation 6 3-8
pH Range, Chemical Cleaning 7 2 - 10
Feed Flow Rate per Vessel < 200 l/min (52.8 gpm)
Brine Flow Rate per Vessel 8 > 40 l/min (10.6 gpm)
Brine/Permeate Flow Ratio 8,9 >6
Pressure Drop (per Element) 9 < 1 kg/cm2 (14 psi)
Pressure Drop (per Vessel) 9 < 2 kg/cm2 (29 psi)

Notes:
1
The recommended design range means safe operational and design conditions under not
so much fouling and scaling. If the SU-series elements are operated outside of the recom-
mended design range, the effective membrane life may be reduced. Refer to the Toray
Technical Bulletin, or contact Toray or the local distributor for design guidelines and further
information for multi element design.
2
High flux operation (operation under high permeate flow rate per single element) on
feedwater turbidity greater than 3 or 4 SDI generally results in frequent cleaning require-
15
ments. Operating pressure should be selected to maintain the flux rate, or permeate flow
rate per single element.
3
Maximum 15 kg/cm2 (214 psi)
4
Maximum 45 °C (113 °F)
5
SDI = Silt Density Index measured according to ASTM D4189
15
6
Both feed and brine water must meet this range.
7
Cleaning and sterilization must meet the recommendations in the Technical Bulletins for
SU-series elements.
8
Flow ratio of brine to permeate for each single element
9
This figure may be reduced when there is hardly any fouling and scaling
10
Element(s) must be cleaned when pressure drop increases to 1.5 times of the initial value.
* Product flow rate declines 25 - 30% when feedwater contains Chlorine.
ROPUR AG continuously improves its products and reserves the right to change above specifications without prior notice. Our general terms of sales and warranty make integral part of these informations and cannot be disclaimed.

Lenntech
[email protected] Tel. +31-152-610-900
www.lenntech.com Fax. +31-152-616-289