Scribd
Upload
490 views4 pages

2512-Z900RS Frame Slider Set PDF

The document provides assembly instructions for installing a slider accessory on a Kawasaki ZR900C/E motorcycle. It lists the required parts and provides step-by-step instructions to install brackets and pads on the left and right sides of the motorcycle. Tightening torques are specified for bolts during assembly. Basic torque values are also provided for general fasteners.

Uploaded by

孙振立
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
490 views4 pages

2512-Z900RS Frame Slider Set PDF

The document provides assembly instructions for installing a slider accessory on a Kawasaki ZR900C/E motorcycle. It lists the required parts and provides step-by-step instructions to install brackets and pads on the left and right sides of the motorcycle. Tightening torques are specified for bolts during assembly. Basic torque values are also provided for general fasteners.

Uploaded by

孙振立
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Assembly Instructions

Model: ZR900C/E
Description: Slider
Part Number: 99994-1010
Flat Rate Time(Hr): 0.3

Before you begin, read through these instructions and check that all parts are present.
Please note that Kawasaki cannot assume any responsibility for damage resulting from incorrect
installation.
Kawasaki recommends that all genuine accessories should be fitted by an authorized Kawasaki
dealer.

The following symbols indicate the information for proper installation and operation in this instruction.
NOTE :
NOTE indicates information that may help or guide you in the operation or service of the
vehicle.
 Indicates a procedural step or work to be done.
 Indicates a procedural sub-step or how to do the work of the procedural step it follows. It also precedes the
text of a NOTE.

Parts List
No. Component Name Part No. Qty Remark
1 O-ring 92055-0885 2 φ11 mm (0.4 in.)
2 Collar 92152-2335 2 φ16 mm (0.6 in.)
3 O-ring 92055-0884 2 φ15.8 mm (0.6 in.)
4 Collar 92152-2334 2 φ22 mm (0.9 in.)
5 Nut 92015-1757 4
6 Bracket 11057-0922 1 Left, “ACC-0105” Mark
7 Bracket 11057-0923 1 Right
8 Bolt 130CB0614 2 L = 14 mm (0.6 in.)
9 Collar 92152-2435 1 Left, L = 30.7 mm (1.2 in.)
10 Pad 39156-2123 1 Left
11 Pad 39156-2124 1 Right
12 Collar 92152-2436 1 Right, L = 28.5 mm (1.1 in.)
13 Bolt 130CB0620 2 L = 20 mm (0.8 in.)
14 Bolt 92153-1931 2 L = 65 mm (2.6 in.)
15 Cover 14093-0516 1 Left
16 Cover 14093-0517 1 Right
17 Bolt 92154-2669 4

 2017 Kawasaki Heavy Industries, Ltd.


Page 1 of 4
Installation Instructions
 Insert the O-ring [1] to the collar [2].
 Insert the O-ring [3] to the collar [4].

 Install the nuts [5].


 Install the collars [2] [4].

Assembly Procedure For Left Side


 Remove:
Left Middle Front Engine Mounting Bolt [A]
Left Middle Engine Bracket Bolts [B]
Left Middle Engine Bracket [C]

NOTE
 This left middle front engine mounting bolt is not necessary
for this accessory.

Page 2 of 4
Installation Instructions
 Install the bracket [6] as shown, and tighten the bolt [8].

NOTE
 This left bracket have a “ACC-0105” mark and the right
bracket have a no mark.

 Install the left middle engine bracket [A] and tighten the left
middle engine bracket bolts [B] temporarily.

 Install:
Collar [9]
Pad Assy [A]
Bolt [13]
Bolt [14]
 Tighten:
Torque – Bolt [14]: 45 N·m (4.6 kgf·m, 33 ft·lb)
Left Middle Engine Bracket Bolts [B]: 25 N·m
(2.5 kgf·m, 18 ft·lb)

 Install:
Cover [15]
Bolt [17]

Assembly Procedure For Right Side

NOTE
 The right side slider installation is the same as left side, note
the following.

 Install the bracket [7] as shown, and tighten the bolt [8].

Page 3 of 4
Basic Torque for General Fasteners
The tables below, relating tightening torque to thread diameter, lists the basic torque for the bolts, nuts and
screws. Use these tables for the bolts, nuts and screws which are not specified the tightening torque
particularly on the previous pages. All of the values are for use with dry solvent-cleaned threads.

For Bolts and Nuts


Torque
Threads dia. (mm)
N·m kgf·m ft·lb
5 4.5 0.46 40 in·lb
6 8.0 0.82 71 in·lb
8 20 2.0 15
10 35 3.6 26
12 60 6.1 44
For Screws, Plastic Part Tightening Portions and Plastic Washer Tightening Portions
Torque
Threads dia. (mm)
N·m kgf·m ft·lb
4 1.2 0.12 11 in·lb
5 3.0 0.31 27 in·lb
6 4.0 0.41 35 in·lb
For Self-Tapping Screws
Torque
Threads dia. (mm)
N·m kgf·m ft·lb
All 1.2 0.12 11 in·lb
For Wellnuts
Torque
Threads dia. (mm)
N·m kgf·m ft·lb
4 0.2 0.02 1.8 in·lb
5 0.5 0.05 4.4 in·lb
6 1.0 0.10 8.9 in·lb

Check tightness of all fasteners in regular interval. Retighten loose fasteners.

P/No. 99958-0380-02

Page 4 of 4

You might also like