Span Tables 2016

Glulam – Made in Denmark

Valid from July 2016

TION STAN
UC
DA
W PROD

RD
13 ·
NE

20

BS :
EN 14080
·

BS EN 14080:2013
Production Standard

Since August 2015 the

production standard for Glulam,
BS EN 14080:2013 has been
mandatory for all manufacturers of
Glulam for load bearing structures.

NEW STANDARD GLULAM GL28cs and GL30c

The revised standard provides com- Strength [MPa] GL28cs GL30c
mon European requirements for the Bending strength f m,k 28 30
production of laminated timber Tensile strength f t,0,k 19.5 19.5
and strength classes for Glulam. f t,90,k 0.5 0.5
Compression strength f c,0,k 24.5 24.5
Designers need to be aware of the f c,90,k 2.5 2.5
strength classes available on Shear strength f v,k 3.5 3.5
the UK market. The strength classes Rolling shear strength f r,k 1.2 1.2
are now GL28cs and GL30c.
Stiffness Properties [MPa] GL28cs GL30c

Although the strength classes have Modulus of elasticity E 0,mean 12500 13000

changed you still get the same E 0,05 10400 10800

quality product from Lilleheden. E 90,mean 300 300

E 90,05 250 250
Shear modulus G mean 650 650
G 05 540 540
Rolling shear modulus G r,mean 65 65
G r,05 54 54

Density [kg/m3] GL28cs GL30c

Density ρk 390 390
Your best choice for Glulam.
ρmean 430 430

2 Span Tables 2016

 Span tables
Simply supported beams

Basis of design
Horizontal beams
Section Ridge beam / Eaves beam / Purlin Floor beam Standards:
size Load width [m] Load width [m] BS EN 1990:2002+A1:2005 + NA
[mm] BS EN 1991-1-1:2002 + NA
2.0 2.5 3.0 3.5 4.0 4.5 2.0 2.5 3.0 3.5 4.0 4.5
BS EN 1991-1-3:2003 + NA
90 x 225 4.2 3.9 3.7 3.5 3.3 3.2 3.6 3.3 3.1 2.9 2.6 2.3
BS EN 1995-1-1:2004+A2:2014 + NA
90 x 270 5.1 4.7 4.4 4.2 4.0 3.9 4.3 4.0 3.8 3.6 3.1 2.8
90 x 315 6.0 5.5 5.2 5.0 4.7 4.5 5.1 4.7 4.4 4.2 3.7 3.3 Strength class:
90 x 360 6.8 6.3 6.0 5.7 5.4 5.2 5.8 5.4 5.1 4.8 4.2 3.7 GL30c acc. to BS EN 14080:2013
90 x 405 7.7 7.1 6.7 6.4 6.1 5.9 6.5 6.1 5.7 5.3 4.8 4.2
115 x 225 4.6 4.3 4.0 3.8 3.6 3.5 3.9 3.6 3.4 3.2 3.1 2.9 Dead loads:
115 x 270 5.5 5.1 4.8 4.6 4.4 4.2 4.7 4.7 4.4 4.2 4.0 3.9 Roof: 0.7 kN/m2 on slope
115 x 315 6.4 6.0 5.7 5.4 5.1 4.9 5.5 5.1 4.8 4.6 4.4 4.2 Floor: 0.5 kN/m2
115 x 360 7.4 6.9 6.5 6.2 5.9 5.7 6.3 5.8 5.5 5.2 5.0 4.7
115 x 405 8.3 7.7 7.3 6.9 6.6 6.4 6.9 6.6 6.2 5.9 5.6 5.3 Imposed loads:
115 x 450 9.2 8.6 8.1 7.7 7.4 7.1 7.4 7.1 6.8 6.6 6.3 5.9 Roof: 0.6 kN/m2 on plan
115 x 495 10.1 9.4 8.9 8.5 8.1 7.8 8.0 7.6 7.3 7.1 6.9 6.5 Floor: 1.5 kN/m2
Partitions: 0.5 kN/m2
140 x 225 4.9 4.5 4.3 4.1 3.9 3.7 4.1 3.8 3.6 3.4 3.3 3.1
140 x 270 5.9 5.5 5.2 4.9 4.7 4.5 5.0 4.6 4.4 4.1 4.0 3.8
Service class: 1
140 x 315 6.9 6.4 6.0 5.7 5.5 5.3 5.9 5.4 5.1 4.9 4.7 4.5
140 x 360 7.8 7.3 6.9 6.6 6.3 6.0 6.6 6.2 5.9 5.6 5.3 5.1 Limiting values for deflections:
140 x 405 8.8 8.2 7.8 7.4 7.1 6.8 7.2 6.9 6.6 6.3 6.0 5.8 wfin ≤ span/250
140 x 450 9.8 9.1 8.6 8.2 7.9 7.6 7.7 7.4 7.1 6.9 6.7 6.4
140 x 495 10.7 10.0 9.5 9.0 8.7 8.3 8.3 7.9 7.6 7.4 7.2 7.0 Fundamental frequency
residential floor:
f1 ≥ 8 Hz
Rafters

Section Roof pitch 0˚-15˚ Roof pitch 16˚-30˚ Lateral restraint to top flange:
size Centres [m] Centres [m] Max distance between lateral
[mm] 2.0 2.5 3.0 3.5 4.0 4.5 2.0 2.5 3.0 3.5 4.0 4.5 support 15 x section width.
90 x 225 4.3 4.0 3.7 3.5 3.4 3.2 4.0 3.7 3.5 3.3 3.2 3.0
Fire requirement:
90 x 270 5.1 4.8 4.5 4.3 4.1 3.9 4.8 4.5 4.2 4.0 3.8 3.7
No fire requirement considered.
90 x 315 6.0 5.6 5.3 5.0 4.8 4.6 5.7 5.3 4.9 4.7 4.5 4.3
90 x 360 6.9 6.4 6.0 5.7 5.5 5.3 6.5 6.0 5.7 5.4 5.2 5.0 Limitation of the span tables:
90 x 405 7.8 7.2 6.8 6.5 6.2 6.0 7.3 6.8 6.4 6.1 5.8 5.6 The span tables serve as a
115 x 225 4.6 4.3 4.0 3.8 3.7 3.5 4.3 4.0 3.8 3.6 3.4 3.3 design aid but do not replace
115 x 270 5.6 5.2 4.9 4.6 4.4 4.3 5.2 4.9 4.6 4.4 4.2 4.0 structural calculations.
115 x 315 6.5 6.1 5.7 5.4 5.2 5.0 6.1 5.7 5.4 5.1 4.9 4.7
115 x 360 7.4 6.9 6.5 6.2 6.0 5.7 7.0 6.5 6.1 5.8 5.6 5.4
115 x 405 8.4 7.8 7.4 7.0 6.7 6.5 7.9 7.3 6.9 6.6 6.3 6.1
115 x 450 9.3 8.7 8.2 7.8 7.5 7.2 8.7 8.1 7.7 7.3 7.0 6.7
115 x 495 10.2 9.5 9.0 8.6 8.2 7.9 9.6 8.9 8.5 8.1 7.7 7.4
140 x 225 4.9 4.6 4.3 4.1 3.9 3.8 4.6 4.3 4.1 3.9 3.7 3.5
140 x 270 5.9 5.5 5.2 5.0 4.7 4.6 5.6 5.2 4.9 4.6 4.4 4.3
140 x 315 6.9 6.5 6.1 5.8 5.5 5.3 6.5 6.1 5.7 5.4 5.2 5.0
140 x 360 7.9 7.4 7.0 6.6 6.4 6.1 7.4 6.9 6.5 6.2 6.0 5.7
140 x 405 8.9 8.3 7.8 7.5 7.2 6.9 8.3 7.8 7.4 7.0 6.7 6.5
140 x 450 9.8 9.2 8.7 8.3 8.0 7.7 9.2 8.6 8.2 7.8 7.5 7.2
140 x 495 10.8 10.1 9.6 9.1 8.8 8.4 10.1 9.5 9.0 8.6 8.2 7.9

Permissible horizontal spans [m]

www.lilleheden.co.uk 3
Glulam – Made in Denmark
– Available here.
National network of
stockists plus weekly
deliveries throughout
mainland GB.

Glulam – Made in Denmark

Lilleheden A/S · Digital Media Centre
County Way · Barnsley S70 2JW
T: 01226 720 760 · F: 01226 720 701
[email protected] · www.lilleheden.co.uk