Scribd
Upload
226 views

Manual Calc. Welded Storage Tank API-650

This mechanical data sheet provides design and material specifications for a large storage tank. Some key details include: - The tank has an inner diameter of 36500 mm and height of 14500 mm. - It is designed to operate between -15 to 155 degrees Celsius and withstand pressures from atmospheric up to -7 mbar.g. - The tank shell, bottom, roof and other components are made of various grades of steel, including A516 Grade 70 and A283 Grade C. - Inspection will include 10% radiography/ultrasonic testing and material testing and inspection by the designated code.

Uploaded by

safar bahari
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
226 views

Manual Calc. Welded Storage Tank API-650

This mechanical data sheet provides design and material specifications for a large storage tank. Some key details include: - The tank has an inner diameter of 36500 mm and height of 14500 mm. - It is designed to operate between -15 to 155 degrees Celsius and withstand pressures from atmospheric up to -7 mbar.g. - The tank shell, bottom, roof and other components are made of various grades of steel, including A516 Grade 70 and A283 Grade C. - Inspection will include 10% radiography/ultrasonic testing and material testing and inspection by the designated code.

Uploaded by

safar bahari
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 1

Mechanical Data Sheet

General
01 Design Code API 650 ASME Stamp No
02 Compliance with P.E.D 97/23/EC CE Stamp No
03 Fluid Hazard Group (P.E.D 97/23/EC)
04 Applicable Project Specs
05
06 Design Data
07 Tank I.D 36500 mm Boot Inside Diameter DDC Sump Depth DDC
08 Height 14500 mm
09 Operating Pressure (Min / Max) Atsmophere / - mbar.g Operating Temp. (Min/Max) -15 155 °C
10 Design Pressure at Top (Int/Ext) 20 / -7 mbar.g Design Temp. (Min/Max) -15 170 °C
11 Corrosion Allowance Weld Joint Coefficient (Long/Circ) 0.85
12
13 Penumatic Test Pressure : (Reinf. Pad) : DDC mbar.g Field Hydrotest Full of Water
14 Wind Loading See Specification Seismic Loading Lateral ± : 0,07 Vertical ± : g
15 Cyclic Operation No
16 Temp. Range (Min/Max) - °C
17 PWHT No
18 Design Stress (Shell / Roof / Bottom) DDC MPa Pipe / Forging DDC DDC MPa
19 Project Design Stress (Anchor Bolt) DDC MPa Concrete Bearing 10 MPa
20 Steam Out Design Case No Steam Coil Design 0,5 MPa @ 180 °C
21
22 Material Specifications
23 Shell / Bottom / Roof A 516 Gr. 70 Insulation Support A 283 Gr. C
24 Nozzle Reinforcement A 516 Gr. 70 Welded Attachment A 283 Gr. C
25 Nozzle Neck Pipe A 336 Gr. 6 Loose Internal Pipe A 333 Gr. 6
26 Nozzle Neck Plate A 516 Gr. 70 Loose Internal Plate A 283 Gr. C
27 Forged Nozzle - Stud Bolts (Ext) A 320 L7M
28 Forged Flange & Blind A 350 LF 2 Nuts (Ext) A 194 7M
29 Welding Fitting DDC Bolt (Int) A 320 8 M
30 Wind Girders DDC Nuts (Int) A 320 8 M
31 Welded Internal DDC Gaskets (Ext) SWGF
32 Special Material Requirement None Gaskets (Int) DDC
33 The Maximum Carbon Content of Carbon Steel shall be 0,23%. Max C.E (IIW) = 0,43%
34 Inpection Data
35 Radiography / Ultrasonic 10% Mill Test Certificate EN 10204-3.1 Required
36 Material Testing & Inspection By DDC Production Control Test Plate As Per Code
37 Painting & Insulation
Finish External Finish Internal
Support (Int/Ext)

You might also like