QS1 Fire Alarm Control Panel

Technical Reference Manual

P/N 3100184 • Rev 2.0 • 12JUL01

Technical Manuals Online! - http://www.tech-man.com

 Compliance Statement The QS1, hereinafter referred to as the FACP or control panel, when
properly installed, operates as a Local Protected Premises Fire Alarm
System in accordance with the following standards:
• NFPA Standard 72, 1999 Edition
• Underwriters Laboratories Standard 864, 7th Edition
• Underwriters Laboratories of Canada Standard ULC S527
In addition, Auxiliary Fire Alarm System operation requires a Reverse
Polarity Module (RPM). Central Station Fire Alarm System operation
requires a Dialer card (DLD).
Installation in accordance with this manual, applicable codes, and the
instructions of the authority having jurisdiction is mandatory.
Limitation of Liability Edwards Systems Technology (EST) shall not under any circumstances
be liable for any incidental or consequential damages arising from loss
of property or other damages or losses owing to the failure of EST
products beyond the cost of repair or replacement of any defective
products. EST reserves the right to make product improvements and
changes to product specifications at any time.
While every precaution was taken during the preparation of this
document to ensure its accuracy, EST assumes no responsibility for
errors or omissions.
Fire Alarm System Automatic fire alarm systems can not guarantee against property
Limitations damage, loss of property, or loss of life. An automatic fire alarm system's
ability to provide early warning of a developing fire may be limited for a
variety of reasons, but mainly due to improper installation or
maintenance.
The best way to minimize system failures is to perform regularly
scheduled preventive maintenance in accordance with national and local
fire codes. All system components and wiring should be tested and
maintained by trained fire alarm system professionals.
FCC Compliance Statement This equipment can generate and radiate radio frequency energy. If this
equipment is not installed in accordance with this manual, it may cause
interference to radio communications. This equipment has been tested
and found to comply within the limits for Class A computing devices
pursuant to Subpart B of Part 15 of the FCC Rules. These rules are
designed to provide reasonable protection against such interference
when this equipment is operated in a commercial environment.
Operation of this equipment is likely to cause interference, in which case
the user at his own expense, will be required to take whatever measures
may be required to correct the interference.

Copyright © 2001. All rights reserved.

Technical Manuals Online! - http://www.tech-man.com

 Content

About this manual • iii

Related documentation • iv
Document history • vi

Chapter 1 Product description • 1.1

System overview • 1.2
Component descriptions • 1.3
Circuit descriptions • 1.4
Controls and indicators • 1.7
Controls and indicators behind the flip-down cover • 1.8
Controls and indicators on the zone annunciator card • 1.9
Interpretation of screen displays • 1.10

Chapter 2 Installation • 2.1

Installation do's and don'ts • 2.2
Installation checklist • 2.3
Two ways to install the cabinet: Surface or semi-flush mount • 2.4
How to assemble the panel • 2.5
Wiring mains ac and earth ground • 2.6
System jumper settings • 2.7
System addressing • 2.9
Terminal definitions • 2.12
Connecting a PT–1S printer • 2.18
Installing standby batteries • 2.19

Chapter 3 Operating instructions • 3.1

Instructions for the Level 1 operator (public mode access) • 3.2
Instructions for the Level 2 operator (emergency mode access) • 3.5
Instructions for the Level 3 operator (maintenance mode access) • 3.7
Instructions for the Level 4 operator (service mode access) • 3.10
QuickReference list • 3.11

Chapter 4 Programming instructions • 4.1

Overview • 4.2
QuickStart setup instructions • 4.4
Customizing the system configuration • 4.12
Setting up an Output Group • 4.19
Setting up a Zone • 4.24

Chapter 5 Standard applications • 5.1

Notification appliance circuits • 5.2
Initiating device circuits • 5.4
Coded alarm signaling • 5.6
Remote station protective signaling system • 5.8
Auxiliary protective signaling • 5.10

QS1 Technical Reference Manual i

Technical Manuals Online! - http://www.tech-man.com

 Content

Chapter 6 Maintenance instructions • 6.1

Pseudo point definitions • 6.2
Maintenance tasks • 6.7

Appendix A System calculations • A.1

Notification appliance circuit maximum wire length calculation • A.2
Signature loop maximum wire length calculations • A.3
Battery calculation worksheet • A.8

Appendix B Barcode library • B.1

Appendix C SIGA-REL programming • C.1

Application block diagram • C.2
Programming instructions • C.3

ii QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Content

About this manual

Organization This manual provides information on how to properly install, wire, and
maintain the FACP and related components, and is organized as
follows:
Chapter 1 provides a detailed description of the fire alarm control panel
and its operation.
Chapter 2 provides instructions for installing the fire alarm control
panel.
Chapter 3 provides instructions for operating the control panel.
Chapter 4 provides instructions for programming the fire alarm system
from the front panel.
Chapter 5 provides simplified wiring schematics for standard
applications.
Chapter 6 provides instructions for maintaining the system.
Appendix A provides worksheets for calculating maximum wire lengths
for notification and Signature circuits, and for sizing standby batteries.
Appendix B provides a set of bar codes that you can use to enter text
for location messages.
Appendix C provides information on how to program the SIGA–REL
using the QS–CU (QuickStart Configuration Utility).

Safety information Important safety admonishments are used throughout this manual to
warn of possible hazards to persons or equipment.

WARNING: Warnings are used to indicate the presence of a hazard

which will or may cause personal injury or death, or loss of service if
safety instructions are not followed or if the hazard is not avoided.

Caution: Cautions are used to indicate the presence of a hazard which

will or may cause damage to the equipment if safety instructions are not
followed or if the hazard is not avoided.

QS1 Technical Reference Manual iii

Technical Manuals Online! - http://www.tech-man.com

 Content

Related documentation

National Fire Protection Association NFPA 70 National Electric Code

1 Batterymarch Park
NFPA 72 National Fire Alarm Code
P.O. Box 9101
Quincy, MA 02269-9101 NFPA 11 Low-Expansion Foam Systems
NFPA 11A Medium- and High-Expansion Foam Systems
NFPA 12 Carbon Dioxide Extinguishing Systems
NFPA 13 Sprinkler Systems
NFPA 15 Water Spray Fixed Systems for Fire Protection
NFPA 16 Deluge Foam-Water Sprinkler and Foam-Water Spray
Systems
NFPA 17 Dry Chemical Extinguishing Systems

Underwriters Laboratories, Inc. UL 38 Manually Actuated Signaling Boxes

333 Pfingsten Road
UL 217 Smoke Detectors, Single & Multiple Station
Northbrook, IL 60062-2096
UL 228 Door Closers/Holders for Fire Protective Signaling
Systems
UL 268 Smoke Detectors for Fire Protective Signaling Systems
UL 268A Smoke Detectors for Duct Applications
UL 346 Waterflow Indicators for Fire Protective Signaling
Systems
UL 464 Audible Signaling Appliances
UL 521 Heat Detectors for Fire Protective Signaling Systems
UL 864 Standard for Control Units for Fire Protective Signaling
Systems
UL 1481 Power Supplies for Fire Protective Signaling Systems
UL 1638 Visual Signaling Appliances
UL 1971 Visual Signaling Appliances

Underwriters Laboratories of Canadian Electrical Code Part 1

Canada
7 Crouse Road
ULC S527 Standard for Control Units for Fire Alarm Systems
Scarborough, ON ULC S524 Standard for the Installation of Fire Alarm Systems
Canada M1R 3A9
ULC S536 Standard for the Inspection and Testing of Fire
Alarm Systems
ULC S537 Standard for the Verification of Fire Alarm Systems
ULC ORD–C693–1994 Central Station Fire Protective Signaling
System and Services

iv QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Content

Edwards Systems Technology 2–CTM City Tie Module Installation Sheet (P/N 270496)
6411 Parkland Drive
CDR–3 Bell Coder Installation Sheet (P/N 3100023)
Sarasota, FL 34243
DLD Dual Inline Dialer Installation Sheet (P/N 3100187)
PS6 Power Supply Card Installation Sheet (P/N 3100201)
QSA–1(X), QSA–2(X) Remote Annunciator Cabinet Installation
Sheet (P/N 3100295)
QS–CPU(X) CPU/Display Unit Installation Sheet (P/N 3100276)
SL30, SL30–1 LED/Switch Card Installation Sheet (P/N
3100193)
SLIC Signature Intelligent Controller Card Installation Sheet
(P/N 3100192)
RS485 (NT–A) Card and QS–232 UART Module Installation
Sheet (P/N 3100191)
ZR8 Relay Card Installation Sheet (P/N 3100190)
SIGA–APS Auxiliary Power Supply Installation Sheet (P/N
387342)
Signature Series Intelligent Smoke and Heat Detectors
Applications Bulletin (P/N 270145)
Signature Series Component Installation Manual (P/N 270497)
EST Strobe Applications Guide (P/N 85000-0049)
QuickStart Online Help Utility (P/N 7350047)
QuickStart ULI and ULC Compatibility Lists (P/N 3100335)
Network Hardware Technical Reference (P/N 250100)

QS1 Technical Reference Manual v

Technical Manuals Online! - http://www.tech-man.com

 Content

Document history

Date Revision Description of changes

24JUN01 1.0 Original release.
12JUL01 2.0 Corrections and additions on pp 2.20, 3.9, 4.4, 4.8, 4.17, A.3.

vi QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Chapter 1
Product description

Summary
This chapter provides a detailed description of the fire alarm control panel and its
operation.

Content
System overview • 1.2
Component descriptions • 1.3
Circuit descriptions • 1.4
Controls and indicators • 1.7
Controls and indicators behind the flip-down cover • 1.8
Controls and indicators on the zone annunciator card • 1.9
Interpretation of screen displays • 1.10

QS1 Technical Reference Manual 1.1

Technical Manuals Online! - http://www.tech-man.com

 System overview
any events.
System hardware capabilities
Hardware capabilities vary depending on cabinet size Off-normal operating mode description
and option card configuration, but generally: The panel operates in off-normal mode any time there is
• Up to four Class A or Class B Signature signaling an event introduced into the system. When this
line circuits that support up to 250 single-address happens, the CPU:
Signature devices each • Changes the contact positions on the appropriate
• Two Class A or Class B notification appliance common relays
circuits • Activates all common alarm outputs (alarm events
• One 30-zone display only)

• Eight dry-contact relays • Turns on the panel buzzer

• 4.5 amps of 24 Vdc power for external notification • Executes the appropriate programmed output
appliances response for the input that signaled the event

• Battery charger capable of charging batteries rated • Sends a record of the event to the appropriate
up to 40 Ah. Maximum battery size for ULC display queue and out the serial port
applications is 30 Ah If there is no operator in attendance, the panel displays
• Up to eight, fully-supervised, mirrored or customized the content of the highest priority display queue
remote annunciators containing a record.
If there is an operator in attendance, the panel displays
Minimum system requirements the content of the current display queue regardless of
any new events introduced into the system.
A Local Protected Premises Fire Alarm System requires
only the FACP (CPU, PS6, and enclosure) with at least
one SLIC programmed with at least one audible output Failsafe operating mode description
circuit and one alarm input circuit. The panel operates in failsafe mode when the CPU
In addition to the hardware requirements of a Local loses the ability to communicate with the PS6 and JP1
system: on the PS6 is in the ON position. When this happens,
the power supply:
• Add a 2–CTM City Tie Module for an Auxiliary Fire
Alarm System • Closes the common trouble relay contacts

• Add a DLD Dual Line Dialer Card or RPM Reverse • Instructs the dialer to send the default trouble
Polarity Module for a Remote Supervising Station message
Fire Alarm System • Monitors the system for any alarm events
• Add a DLD Dual Line Dialer Card or RPM Reverse If an alarm event occurs, the power supply:
Polarity Module for a Central Station Fire Alarm
System • Changes the contact positions on the common alarm
relay
• Add a SIGA–REL and SIGA–APS for Releasing
Device Service • Turns on all conventional common alarm outputs.
Signature common alarm outputs are not affected.
Normal operating mode description • Instructs the dialer to send the default alarm
message
The panel operates in normal mode in the absence of
any alarm, supervisory, trouble, and monitor events. In
normal mode, the control panel monitors the system for

1.2 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Component descriptions

1 2 3 4 5 6 7

J6

J5

J7

J8 J3

JP1 CONFIGURATION
PIN 1 & 2 = MODEM PWR
PIN 2 & 3 = RTS

JP1

3 1 J2

9 8

1. SL30 LED/Switch Card: Provides thirty circuits for 6. SLIC Signature Loop Intelligent Controller Card:
point or zone annunciation. Each circuit has two LEDs Provides one Class A or Class B signaling line circuit
for annunciating alarm, supervisory, and trouble (loop) for connecting Signature series detectors and
signals, and a button numbered from 1 to 30. modules. The SLIC also provides two Class A or Class
B notification appliance circuits (NACs) for connecting
2. CPU/Display: Provides operator access to system
polarized 24 Vdc notification appliances (horns,
messages, status information, and programming strobes).
menus, and executes system responses based on the
panel programming. 7. DLD Dual Line Dialer Card: Provides two
telephone line connections for sending system
3. AC wiring block and fuse holder: Provides
messages to a compatible Digital Alarm Communicator
connections for mains ac (primary power) and 5A fuse.
Receiver.
4. Cabinet enclosure: Houses the panel electronics
8. Standby batteries: Provides dc power to the panel
and standby batteries.
electronics in the absence of ac power.
5. PS6 Power Supply Card: Provides primary dc
9. Transformer: Converts 120 Vac or 240 Vac supply
power for the panel electronics and auxiliary power for
into 24 Vdc for the panel electronics.
external circuits. The PS6 also provides common
alarm, supervisory and trouble relays.

QS1 Technical Reference Manual 1.3

Technical Manuals Online! - http://www.tech-man.com

 Product description

Circuit descriptions
PS6 Power Supply Card
1. Relay 1 (Common Alarm)
Style: Form C
Contact rating: 1 A @ 20.4 – 26.4 Vdc (0.6 PF) 2 3 4 5 6
Wire size: 18 to 12 AWG (0.75 to 2.5 mm²)
1 7
Nonsupervised and power-limited only when
connected to a power-limited source
2. Relay 2 (Common Supervisory)
Style: Normally-open
Contact rating: 1 A @ 20.4 – 26.4 Vdc (0.6 PF)
Wire size: 18 to 12 AWG (0.75 to 2.5 mm²)
Nonsupervised and power-limited only when
connected to a power-limited source
3. Relay 3 (Common Trouble)
Style: Normally-open, held closed
Contact rating: 1 A @ 20.4 – 26.4 Vdc (0.6 PF)
Wire size: 18 to 12 AWG (0.75 to 2.5 mm²)
Nonsupervised and power-limited only when
connected to a power-limited source
4. Relay 4 (Programmable)
Style: Normally-open
Contact rating: 1 A @ 20.4 – 26.4 Vdc (0.6 PF)
Wire size: 18 to 12 AWG (0.75 to 2.5 mm²)
Nonsupervised and power-limited only when 9 8
connected to a power-limited source
5. Smoke/Accessory Power
Output: Continuous or interruptible via jumper
selection
Voltage: 24 Vdc, regulated
Current: 250 mA
Wire size: 18 to 12 AWG (0.75 to 2.5 mm²)
Supervised and power-limited
6. RS485 8. AUX Power #1, #2, and #3
Wire size: 18 to 12 AWG (0.75 to 2.5 mm²) Voltage: 17.5 – 26.4 Vdc FWR (full wave rectified)
Wire type: Twisted pair, six twists per foot minimum Current: 1.5 A each
Circuit capacitance: 0.4 µF Wire size: 18 to 12 AWG (0.75 to 2.5 mm²)
Circuit resistance: 100 Ω Power-limited and supervised for short circuit
Supervised and power-limited conditions only
7. RS232 9. Battery Circuit
Wire size: 18 to 12 AWG (0.75 to 2.5 mm²) Charge current: 2 A
Nonsupervised and power-limited Charge capacity: 40 Ah (UL), 30 Ah (ULC)
Wire length: 20 ft maximimum Supervised and nonpower-limited

1.4 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 SLIC Signature Loop Intelligent Controller Card circuits

1. NAC #1
Configuration: Class B or Class A
Output voltage: 24 Vdc, nominal
Output current: 2.0 A @ 24 Vdc 1 2
Wire size: 18 to 12 AWG (0.75 to 2.5 mm²)
End of line resistor: 10 kΩ, 1/2W
Supervised and power-limited
2. NAC #2
Configuration: Class B or Class A
Output voltage: 24 Vdc, nominal
Output current: 1.0 A @ 24 Vdc
Wire size: 18 to 12 AWG (0.75 to 2.5 mm²)
End of line resistor: 10 kΩ, 1/2W
Supervised and power-limited
3. Signature Loop
Configuration: Class B (Style 4) or Class A (Style 6)
Capacity: 125 Signature detectors, 125 Signature single-address
modules
Wire size: 18 to 12 AWG (0.75 to 2.5 mm²)
4 3
Circuit resistance: 65 Ω
Circuit capacitance: 0.3 µF
Supervised and power-limited
4. NAC Riser In/Out
Voltage: 24 Vdc, nominal
Wire size: 18 to 12 AWG (0.75 to 2.5 mm²)

ZR8 Relay Card circuits

1. Dry-contact relays R1 – R4
Outputs: Normally-open or normally-closed contacts via jumper 1
selection
Contact rating: 24 Vdc @ 1.0 A
Wire size: 18 to 12 AWG (0.75 to 2.5 mm²)
Nonsupervised, and power-limited only when connected to a
power-limited source
2. Dry-contact relays R5 – R8
Outputs: Normally-open or normally-closed contacts via jumper
selection
Contact rating: 24 Vdc @ 1.0 A
Wire size: 18 to 12 AWG (0.75 to 2.5 mm²)
Nonsupervised, and power-limited only when connected to a
power-limited source

QS1 Technical Reference Manual 1.5

Technical Manuals Online! - http://www.tech-man.com

 Product description

DLD Dual Line Dialer Card circuits

1. Line #1
Supervised and nonpower-limited
2. Line #2
Supervised and nonpower-limited 1 2

RS485 (NT–A) Class A Card circuits

1. Secondary RS485 channel

Wire size: 18 to 12 AWG (0.75 to 2.5 mm²)
Supervised and power-limited
2. Primary RS485 channel 1 2
Wire size: 18 to 12 AWG (0.75 to 2.5 mm²)
Supervised and power-limited

1.6 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Controls and indicators

1 2 3 4 5 6 7 8 9

12
11
10

1. Text display and controls: Displays system 5. Monitor LED: Indicates the panel posted a monitor
messages, status information, programming menus. event record into the corresponding display queue.
6. Trouble LED: Indicates the panel posted a trouble
Moves the cursor up one line at a time or to the event record into the corresponding display queue.
previous record in the display queue
7. Ground Fault LED: Indicates a ground fault in the
Moves the cursor down one line at a time or to system wiring. Ground faults also signal a system
the next record in the display queue trouble.
8. CPU Fail LED: Indicates an unexpected reboot or
Moves the cursor right one character at a time failure with the microprocessor. CPU failures also
or to the next display queue signal a system trouble.

Moves the cursor left one character at a time 9. Power LED: Indicates the panel has ac power.
or to the previous display queue 10. Panel Silence/Acknowledge button/LED: Turns
off the panel buzzer and acknowledges all events. The
Enters operator input and selects menu items Panel Silenced LED indicates that all off normal events
2. Alarm LED: Indicates the panel posted an alarm have been acknowledged and the internal buzzer is
event record into the corresponding display queue. off.

3. Supervisory LED: Indicates the panel posted a 11. Status button: Displays the Status menu from
supervisory event record into the corresponding which you can identify active or disabled points in the
display queue. system.

4. Disable/Test LED: Indicates part of the system is 12. Help button: Provides additional information for
disabled or is currently under test. Disabled the event record selected on the display.
components also signal a system trouble.

QS1 Technical Reference Manual 1.7

Technical Manuals Online! - http://www.tech-man.com

 Product description

Controls and indicators behind the flip-down cover

7 8 9 2
4 5 6
1 2 3 4 5 6 7 8 9 0

1. Enable Controls key switch: Gives priority access 6. Drill button: Turns notification appliances on
to control functions reserved for operators with Level 2 according to the panel programming but does not
access. place the panel in alarm. The LED indicates when the
panel is in Drill mode.
2. Barcode scanner jack: Input point for optional
barcode scanner. 7. Menu button: Displays the operator menus.
3. Numeric keypad: Numbered buttons for entering 8. Delete button: Returns to the previous menu or
data and selecting menu options. back spaces the cursor.
4. Reset button: Restores devices or zones in alarm 9. Enter button: Press the Enter button to accept
or trouble to their standby condition. The LED indicates information from the operator or continue to the next
when the panel is resetting. item.
5. Alarm Silence button: Turns active notification
appliances off according to the panel programming.
Pressing Alarm Silence a second time turns them back
on. The LED indicates when the panel is in alarm and
operating with notification appliances turned off.

1.8 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Controls and indicators on the zone annunciator card

1 2 3

1 6 11 16 21 26

2 7 12 17 22 27

3 8 13 18 23 28

4 9 14 19 24 29

5 10 15 20 25 30

1. Zone display button: Displays an event record for Note: ULC requires that every fire panel have the
each device in the corresponding zone that signaled capability to visually display system status by means of
an alarm. specific indicators for each zone. All status changes
must clearly indicate that the information is an Alarm
2. Zone active LED: Indicates a device in the
(ALM), Supervisory (SUP), Trouble (TBL), or Monitor
corresponding zone signaled an alarm condition. (MON).
3. Zone trouble LED: Indicates a device or wiring fault
in the corresponding Zone.

QS1 Technical Reference Manual 1.9

Technical Manuals Online! - http://www.tech-man.com

 Product description

Interpretation of screen displays

HH:MM:SS MM/DD This is what the panel display looks like when there are no event records
posted in a display queue.
HH:MM:SS is the current time in hours, minutes, and seconds
MM/DD is the current month and date
nnnn is the number times the panel went into alarm since being placed into
System service
Normal

Project Name

Alarm History:
nnnn

HH:MM:SS This is what the panel display looks like when there are event records
Axxx Dxxx posted in a display queue.
HH:MM:SS is the current time in hours, minutes, and seconds
nnn event name
Axxx is the current number of active points
Custom message 1
Custom message 2 Dxxx is the current number of disabled points

These items comprise the event record:

nnn event name
Custom message 1 nnn is the posting sequence number (001 = first, 002 = second, and so on)
Custom message 2 event name is the event produced when the device changed states. Refer
to Table 1-1.
P:pp C:cc D:ddd is the address of the device that signaled the event (P =
ALM SUP TRBL MON panel number, C = card number, D = device number)
aaa sss ttt mmm
The event record may also include a custom message that typically indicates
the location of the device, depending on the panel programming.

These items indicate the content of the display queues:

aaa is the number of alarm event records (highest priority)
sss is the number of supervisory event records
ttt is the number of trouble event records
mmm is the number of monitor event records (lowest priority)

1.10 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Table 1-1: Event descriptions

Event name Event type Description

ALARM ACTIVE Alarm Smoke detector active
ALARM VERIFY Monitor Alarm active. Performing auto reset.
AND GROUP Alarm And group active
BAD PRSONATY Trouble SIGA personality mismatch
BAD TYPE Trouble SIGA type mismatch
COMM FAULT Trouble Communication failure
DEV COMPATIB Trouble SIGA compatibility fault
DIRTY HEAD Trouble Dirty smoke detector. No compensation remaining
DISAB SOUND Trouble Sounder is disabled (EN–54 only)
DISABLED Trouble Device is disabled
GROUND FAULT Trouble Ground fault
HEAT ALARM Alarm Heat detector active
INTERNAL TBL Trouble Internal system trouble
LCL MONITOR Monitor Common monitor
LCL TROUBLE Trouble Generic trouble.
MAINT ALERT Monitor Dirty smoke detector. Some compensation remaining
MATRIX GROUP Alarm Matrix group active
MONITOR Monitor Active non-latching input circuit.
OBJECT RUN Monitor Service group is enabled and governing all defined objects
PREALARM Monitor Possible fire condition exists.
PULL STATION Alarm Manual fire alarm box active
SERVICE GROUP Trouble Service group active
SUPERVISORY Supervisory A device used to monitor a component of the fire suppression system is active
SWITCH Monitor Operator presses switch on LED/Switch card
TAMPER Supervisory Sprinkler tamper active
TEST Trouble A member of a Service group under test is activated
TIME CONTROL Monitor Time control active
TROUBLE Trouble Common trouble
TROUBLE OPEN Trouble Open detected on a supervised output device's field wiring
TROUBLE SHORT Trouble Short detected on a supervised output device's field wiring
UNEXPECT DEV Trouble Signature device not defined in database
WATERFLOW Alarm Water flowing through the sprinkler system
ZONE ALARM Alarm Alarm zone active
ZONE MONITOR Monitor Monitor zone active
ZONE SUPER Supervisory Supervisory zone active

QS1 Technical Reference Manual 1.11

Technical Manuals Online! - http://www.tech-man.com

 Product description

1.12 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Chapter 2
Installation

Summary
This chapter provides instructions for installing the fire alarm control
panel.

Content
Installation do's and don'ts • 2.2
Installation checklist • 2.3
Two ways to install the cabinet: Surface or semi-flush mount • 2.4
How to assemble the panel • 2.5
Wiring mains ac and earth ground • 2.6
System jumper settings • 2.7
System addressing • 2.9
Terminal definitions • 2.12
Connecting a PT–1S printer • 2.18
Installing standby batteries • 2.19
Connecting a service computer • 2.20

QS1 Technical Reference Manual 2.1

Technical Manuals Online! - http://www.tech-man.com

 Installation

Installation do's and don'ts

When installing cabinets... DO use fasteners that can support the full weight of the cabinet
and standby batteries. Tighten firmly to avoid vibrations.
DO NOT drill inside the cabinet with circuit cards installed.
Remove all metal filings before installing the circuit cards.
DO NOT recess the cabinet into the wall deeper than 2–11/16
inches (68.2 mm) from the finished wall surface to allow room
for the trim kit.

When installing circuit boards... DO ground yourself with an approved static-protective wrist
strap when handling circuit boards.
DO keep circuit boards in their protective antistatic packaging.
Remove only for inspection or installation.
DO NOT touch component leads and connector pins when
handling circuit boards.
DO disconnect ac power and batteries before installing or
removing circuit boards. Installing or removing circuit boards
while the control panel is energized may damage the
equipment.

When installing circuit wiring... DO use appropriately sized wire for the application. Incorrectly-
sized wires degrade circuit performance.
DO make sure there are no wire-to-ground shorts or wire-to-
wire shorts before connecting field wires to the panel.
DO NOT over tighten screw terminals. Over tightening may
strip screw terminal threads and cause loose connections.

When installing Signature loops... DO NOT install more than fifteen SIGA–UMs or MABs
configured for two-wire smoke detectors on a loop.
DO NOT install more than seven SIGA–UMs or MABs
configured for two-wire smoke detectors on loops with isolator
devices.
DO NOT install more than ten SIGA–RELs on a loop. You must
use the QuickStart configuration utility to program a SIGA–REL.
Refer to the technical manual supplied with the SIGA–REL and
appendix C of this manual for programming information.

When installing standby batteries... DO NOT install standby batteries until after you completely
install and test the system.

2.2 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Installation

Installation checklist

¨ Prepare the site Make sure the installation location is free from construction dust
and debris, and immune to extreme temperature ranges and
humidity.
Allow enough floor and wall space so the panel can be installed
and serviced without obstructions.
Pull and tag all field wiring. See Appendix A for wire length
calculations.
¨ Unpack the equipment Open the shipping container and carefully unpack the
equipment. Check for any visible signs of damage. If there is
any damage, return the equipment to the place of purchase.
Keep the shipping container and packing material until after
completely installing and testing the equipment. Use the
shipping container to return the equipment to the manufacturer.
Verify the shipping container contains the correct parts. If any
parts are missing or damaged, return the equipment to the
manufacturer.
¨ Install the cabinet
¨ Assemble the panel
¨ Wire mains ac and earth ground Bring the primary power conductors into the left side
(nonpower-limited area) of the cabinet and wire to the ac
terminal block.

WARNING: Make sure that the circuit breaker providing ac

power is switched off before connecting wires to the terminal
block.

¨ Connect the field wiring Bring the field wiring into the power-limited area of the cabinet.
Verify there are no open or shorts then connect the wires to
their respective terminals.
¨ Use the AutoLearn and AutoLoop Refer to chapter 4.
utilities to configure the system
¨ Customize the system Refer to chapter 4.
configuration
¨ Install the standby batteries Do not connect standby batteries to the panel until after
completely testing the panel.
¨ Perform system acceptance tests

QS1 Technical Reference Manual 2.3

Technical Manuals Online! - http://www.tech-man.com

 Installation

Two ways to install the cabinet: Surface or semi-flush mount

Surface mount instructions 4-7/8 in

(12.38 cm)
1. Position the cabinet on the 12-1/4 in (31.1 cm)
finished wall surface.
2. Fasten the cabinet to the
wall surface where
indicated. Tighten firmly.

18-3/16 in
(46.2 cm)

14-1/2 in (36.9 cm)

Semi-flush mount 2-11/16 in

(6.82 cm)
instructions 2-3/16 in
(5.56 cm)
1. Frame the interior wall as
required to support the full
weight of the cabinet and
standby batteries.
2. Fasten the cabinet to the
framing studs where
indicated. Tighten firmly.

2.4 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Installation

How to assemble the panel

Circuit card instructions

1. Lock the PS6 onto the DIN rail and configure
jumpers.
2. Attach the ground wire to the cabinet. Tighten
the lock nut firmly to ensure a good
mechanical and electrical connection.
3. Plug the transformer into the PS6.
PS6 SLIC
4. Install remaining option cards according to
their respective installation sheets.
XFMR

Door mounting instructions

1. Bolt the door to the cabinet back box.
2. Attach one end of the ground strap to the door
and the other to the back box.
3. Screw the CPU/Display unit to the cabinet
door.
4. Plug one end of the ribbon cable into the
CPU/Display and the other end into the PS6.
5. Screw the key switch ground wire and the
CPU cover to the cabinet door.

QS1 Technical Reference Manual 2.5

Technical Manuals Online! - http://www.tech-man.com

 Installation

Wiring mains ac and earth ground

H G
(L1) (E)
N
(L2)

CAUTION: The middle connection on the ac

terminal block makes a mechanical connection to
chassis (earth) ground. Do not allow the ac hot
and neutral conductors to make contact with the
middle connector on the ac terminal block.

Wiring instructions Notes

1. Bring the mains ac conductors into the cabinet Keep power-limited wires in the shaded area and
through the 3/4–1/2 inch combination knock- nonpower-limited wires in the nonshaded area.
outs on the left side or upper left corner of the
Maintain a 1/4-inch separation between the
cabinet.
mains ac and battery wires (power-limited) and
2. Wire the hot (H, L1), neutral (N, L2), and and all other nonpower-limited wiring at all times.
ground (G, E) conductors to the ac terminal
block as shown.
3. Insert tabbed end of terminal block cover
(deadfront) into the slot provided on the side
of the cabinet.

2.6 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Installation

System jumper settings

PS6 Power Supply Card jumpers

JP2 configures the Smoke/Accessory power
output for constant or resettable 24 Vdc.
JP2
• Set JP2 to ACC PWR to provide constant ACC PWR
24 Vdc for external equipment.
SMK PWR
• Set JP2 to SMK PWR to provide resettable
24 Vdc for four-wire smoke detectors
JP1 configures the panel for failsafe operation.
Failsafe allows the system to generate output
responses even when the CPU loses
communication with the power supply card.
JP1
• Set JP1 to ON to turn failsafe mode on
• Set JP1 to OFF to turn failsafe mode off ON OFF

SLIC Signature Loop Intelligent Controller

Card jumpers
JP1 and JP2 selects the signal that the SLIC
uses for the notification appliances connected to
NAC1.
JP1 JP2
Note: NAC 2 always uses the external signal
EXT
connected to TB2–3 and TB2–4.
• Set JP1 and JP2 to INT to use the 24 Vdc INT
that comes from the PS6 over the bus
connection.
• Set JP1 and JP2 to EXT to use the 24 Vdc
that comes from an external source
connected to TB2–3 and TB2–4.
CAUTION: Do not set JP1 and JP2 to EXT if
strobes are connected to NAC 1 and a coded
signal is connected to TB2–3 and TB2–4.

QS1 Technical Reference Manual 2.7

Technical Manuals Online! - http://www.tech-man.com

 Installation

ZR8 Relay Card jumpers

JP1 – JP8 configure which relay contacts are R4+ R4–
present on the terminal connections for R1 – R8,
respectively.
JP4
The normal operating state of the relay (on or off
when the panel is normal) determines whether
the terminal connections are normally-open or
normally-closed.
The figure to the right shows the relay contact
positions when the relay is turned off.

RS485 (NT–A) Card jumpers

JP1 configures ground fault supervision for Class
A remote annunciators.
• Set a shorting plug across JP1–1 and JP1–2 1 2 3
when the PS6 powers the remote
JP1
annunciator and provides ground fault
supervision
• Set a shorting plug across JP1–2 and JP1–3
when an external supply powers the remote
annunciator and provides ground fault
supervision

2.8 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Installation

System addressing

Card addresses ON ON

= 01 = 08
Each option card installed in the panel is 1 2 3 4 1 2 3 4

assigned a unique card address. Only the SLIC,

ON ON
ZB16–8, ZA8–2, and ZR8 have card addresses
that you can set. The CPU, DLD and PS6 card = 02 = 09
1 2 3 4 1 2 3 4
addresses are fixed.
ON ON
00: Reserved for the CPU = 03 = 10
1 2 3 4 1 2 3 4
01–07: Used for the SLIC or ZR8
08–13: Used for the ZR8 ON ON

= 04 = 11
14: Reserved for the DLD 1 2 3 4 1 2 3 4

15: Reserved for the PS6 ON ON

= 05 = 12
1 2 3 4 1 2 3 4

ON ON

= 06 = 13
1 2 3 4 1 2 3 4

ON

= 07
1 2 3 4

Tip: When you install the option cards, set the

card addresses in consecutive order as you
move away from the power supply starting at
address 01.

01

QS1 Technical Reference Manual 2.9

Technical Manuals Online! - http://www.tech-man.com

 Installation

SLIC Signature Loop Intelligent Controller PPCC270

Card device addresses PPCC271
The device address format is PPCCDDD, where:
PP is the panel number (01)
CC is the card number (any number between 1
and 7 depending on the setting of SW1)
DDD is the device or circuit number, where:
• 001–125 are Signature automatic detectors
and SIGA–IM isolator modules
• 126–250 are Signature modules
• 270 is the NAC 1 output circuit
PPCC001 PPCC126
• 271 is the NAC 2 output circuit to to
PPCC125 PPCC250
Note: Some Signature modules use two or more
device addresses.

ZR8 Relay Card device addresses PPCC002 PPCC003

PPCC001 PPCC004
The device address format is PPCCDDD, where:
PP is the panel number (01)
CC is the card number (any number between 1
and 13 depending on the setting of SW1)
DDD is the device number, where 001 – 008 are
relays 1 – 8, respectively

PPCC006 PPCC007
PPCC005 PPCC008

2.10 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Installation

SL30 LED/Switch Card device addresses GG011, GG012

The device address format is GGSS for

switches and GGSSL for LEDs, where: GG013

GG is the group number (01 for SL30, 02 for

SL30–1)
1 GG01
SS is the switch number
L is the LED number, where:
06-10 11-15 16-20 21-25 26-30
• 1 is the red Alarm LED
• 2 is the yellow Active LED
• 3 is the yellow Trouble LED 6 11 16 21 26

GG02 2 7 12 17 22 27

GG03 3 8 13 18 23 28

GG04 4 9 14 19 24 29

GG05 5 10 15 20 25 30

QS1 Technical Reference Manual 2.11

Technical Manuals Online! - http://www.tech-man.com

 Installation

Terminal definitions

Table 2-1: PS6 Power Supply card terminal definitions

SMOKE
RELAY 1 RELAY 2 RELAY 3 RELAY 4 ACC PWR RS485 RS232
NO C NC C NO C NO C NO N.C. + – + – RTS TX RX COM

TB1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

BATT PWR
+ – NC

TB2

1 2 3

AUX POWER
AUX1 AUX2 COM AUX3 COM

TB3

1 2 3 4 5

Terminal No. Name Description

TB1–1, –2 Relay 1 NO, C Normally-open relay contacts that close automatically when
the panel processes an alarm event. The contacts remain
closed until all active alarm points restore and the panel
resets.
TB1–2, –3 Relay 1 C, NC Normally-closed relay contacts that open automatically when
the panel processes an alarm event. The contacts remain
open until all active alarm points restore and the panel resets.
TB1–4, –5 Relay 2 C, NO Normally-open relay contacts that close automatically when
the panel processes a supervisory event. The contacts
remain closed until the active supervisory point restores.
TB1–6, –7 Relay 3 C, NO Normally-open relay contacts that close automatically when
the panel energizes. The contacts open when the panel
processes a trouble event or when the panel loses power and
remain open until the trouble condition restores.
TB1–8, –9 Relay 4 C, NO Normally-open relay contacts that close depending on how
the user programs the panel.
TB1–10 N.C. Not used
TB1–11, –12 SMK/ACC PWR +, – Provides regulated 24 Vdc for four-wire smoke detectors or
accessory devices depending on jumper setting.
TB1–13, –14 RS485 +, – Connects to the Channel 1 input on a remote annunciator

2.12 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Installation

Terminal No. Name Description

TB1–15 RS232 RTS Not used
TB1–16 RS232 RX Connects to the data transmit (TX) terminal on a peripheral
device.
TB1–17 RS232 TX Connects to the receive data (RX) terminal on a peripheral
device.
TB1–18 RS232 COM Connects to the common ground (COM) terminal on a
peripheral device.
TB2–1 BATT PWR + Connects to the positive terminal on the standby battery.
TB2–2 BATT PWR – Connects to the negative terminal on the standby battery.
TB2–3 NC Not used.
TB3–1 AUX1 Provides 24 Vdc, FWR power to auxiliary devices.
Note: AUX1, AUX2, and AUX3 can not be used to power
remote annunciators
TB3–2 AUX2 Provides 24 Vdc, FWR power to auxiliary devices.
TB3–3 COM Negative reference for AUX1 and AUX2 outputs.
TB3–4 AUX3 Provides 24 Vdc, FWR power to auxiliary devices.
TB3–5 COM Negative reference for AUX3 output.

QS1 Technical Reference Manual 2.13

Technical Manuals Online! - http://www.tech-man.com

 Installation

Table 2-2: SLIC Signature Loop Intelligent Controller card

NAC 1 NAC 2
B+ B– A+ A– B+ B– A+ A–

TB1

1 2 3 4 5 6 7 8

OUT IN LOOP
+ – + – A+ A– B+ B–

TB2

1 2 3 4 5 6 7 8

Terminal No. Name Description

TB–1, –2 NAC 1 B+, B– Connects to the IN +/– terminals of the first device on the
NAC circuit. Polarity markings (+/–) indicate output signal
polarity with the circuit turned off. Polarity reverses with the
circuit turned on.
TB–3, –4 NAC 1 A+, A– Connects to the OUT +/– terminals of the last device on the
NAC circuit. Class A configuration only.
TB–5, –6 NAC 2 B+, B– Connects to the IN +/– terminals of the first device on the
NAC circuit. Polarity markings (+/–) indicate output signal
polarity with the circuit turned off. Polarity reverses with the
circuit turned on.
TB–7, –8 NAC 2 A+, A– Connects to the OUT +/– terminals of the last device on the
NAC circuit. Class A configuration only.
TB2–1, –2 OUT+, OUT– Connects to the next device on the same 24VDC riser used
to provide 24 Vdc to NAC 1 and NAC 2.
TB2–3, –4 IN+, IN– Connects to the signal source used to provide 24 Vdc to NAC
1 and NAC 2.
TB2–5, –6 LOOP A+, A– Connects to the DATA OUT +/– terminals of last device on
the Signature signaling line circuit. Class A configuration only.
TB2–7, –8 LOOP B+, B– Connects to the DATA IN +/– terminals of the first device on
the Signature signaling line circuit.

2.14 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Installation

Table 2-3: ZR8 Relay card terminal definitions

+ R1 – + R2 – + R3 – + R4 –

TB1

1 2 3 4 5 6 7 8

+ R5 – + R6 – + R7 – + R8 –

TB2

1 2 3 4 5 6 7 8

Terminal No. Name Description

TB1–1, –2 R1+, R1– Terminal connections for relay 1.
TB1–3, –4 R2+, R2– Terminal connections for relay 2.
TB1–5, –6 R3+, R3– Terminal connections for relay 3.
TB1–7, –8 R4+, R4– Terminal connections for relay 4.
TB2–1, –2 R5+, R5– Terminal connections for relay 5.
TB2–3, –4 R6+, R6– Terminal connections for relay 6.
TB2–5, –6 R7+, R7– Terminal connections for relay 7.
TB2–7, –8 R8+, R8– Terminal connections for relay 8.

QS1 Technical Reference Manual 2.15

Technical Manuals Online! - http://www.tech-man.com

 Installation

Table 2-4: RS485 (NT–A) Class A card terminal definitions

RS485
+ CH2 – + CH1 –

TB1

1 2 3 4

Terminal No. Name Description

TB1–1, –2 CH2+, CH2– Connects to CH2+/– on the first remote annunciator on the Class
A RS485 riser.
TB1–3, –4 CH1+, CH1– Connects to CH1+/– on the first remote annunciator on the Class
A RS485 riser.

2.16 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Installation

Table 2-5: DLD Dual Line Dialer card terminal definitions

LINE 1 LINE 2
IN OUT IN OUT
TIP RING TIP RING TIP RING TIP RING

TB1

1 2 3 4 5 6 7 8

Terminal No. Name Description

TB1–1 LINE 1 TIP IN Connects to the Tip In connector on the telco side of an RJ31X
block via an RJ–12 modular cable.
TB1–2 LINE 1 RING IN Connects to the Ring In connector on the telco side of an RJ31X
block via an RJ–12 modular cable.
TB1–3 LINE 1 TIP OUT Connects to the Tip Out connector on the protected premises
side of an RJ31X block via an RJ–12 modular cable.
TB1–4 LINE 1 RING OUT Connects to the Ring Out connector on the protected premises
of an RJ31X block via an RJ–12 modular cable.
TB1–5 LINE 2 TIP IN Connects to the Tip In connector on the telco side of an RJ31X
block via an RJ–12 modular cable.
TB1–6 LINE 2 RING IN Connects to the Ring In connector on the telco side of an RJ31X
block via an RJ–12 modular cable.
TB1–7 LINE 2 TIP OUT Connects to the Tip Out connector on the protected premises
side of an RJ31X block via an RJ–12 modular cable.
TB1–8 LINE 2 RING OUT Connects to the Ring Out connector on the protected premises
of an RJ31X block via an RJ–12 modular cable.

QS1 Technical Reference Manual 2.17

Technical Manuals Online! - http://www.tech-man.com

 Installation

Connecting a PT–1S printer

For control panels with only a printer

1. Locate the printer in the same room as and
within 20 ft of the panel (printer wiring is
nonsupervised and power-limited). PS6 TB1–18
COM–COM
7
TO
2. Wire the printer cable to the RS232 PT–1S
connections on the power supply card then PS6 TB1–17 TX–RX
3
plug the cable into the printer. PS6 TB1–16 RX–TX
2

3. Set the printer switches for 9600 bps, 8 bits,

DB–25P
no parity. Refer to the documentation included REAR VIEW
with the printer for more details.

For control panels with a printer and a CDR–3

Bell Coder module TB1
CDR–3 TB2–4 1
1. Install the IOP3A in the same enclosure as the 2
CDR–3. Refer to appendix B. CDR–3 TB2–5 3
4
2. Wire the IOP3A to the CDR–3. CDR–3 TB2–6 5

3. Wire the printer cable to the RS232 6

CDR–3 TB2–7

JB1
connections on the IOP3A then plug the cable

UP

1
2
3
into the printer.

SW1
PS6 TB1–17
4. Configure the IOP3A as follows:
JP1 = 2–3

JB4
JP2 = ON
JP3 = ON
JP4 = ON IOP3A
TO
SW1 = UP PT–1S
7 32
5. Set the printer switches for 9600 bps, 8 bits,
TB3 TB2
no parity. Refer to the documentation included
JB3

JB2

with the printer for more details. COM–COM

1
DB–25P 2
RxD–TxD
REAR VIEW 3
TxD–RxD
4

2.18 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Installation

Installing standby batteries

For batteries rated at 10 Ah or less

1. Place the batteries in the bottom of
the control panel.
2. Wire the batteries to the PS6.
Notes
Do not run wires through the bottom
knock-outs when batteries are installed in
+ –
the control panel.
Battery wiring is supervised and
nonpower-limited.
Maintain a 1/4-inch separation
between power-limited and nonpower-
limited wiring at all times.

For batteries rated greater than 10 Ah

1. Place the batteries in a BC-1 Battery
Cabinet. The cabinet must be
mounted within 3 ft of the control
panel, in the same room, and
connected with conduit.
2. Wire the batteries to the PS6.

Note: Install, maintain, and test standby + –

batteries in accordance with NFPA 72.

+ + – –

BC-1

QS1 Technical Reference Manual 2.19

Technical Manuals Online! - http://www.tech-man.com

 Installation

Connecting a service computer

Connection of a service computer to the DB-9F

REAR VIEW
control panel requires programming
cable P/N 260097, ordered separately.
1
Connection of a service computer to a RTS NOT USED 9
remote annunciator requires PS6
RX
programming cable P/N 360136 and a TX
RJ–11 to DB9 adapter P/N 240507, both COM
ordered separately.
P/N 260097

2.20 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Chapter 3
Operating instructions

Summary
This chapter provides instructions for operating the control panel.

Content
Instructions for the Level 1 operator (public mode access) • 3.2
Instructions for the Level 2 operator (emergency mode access) • 3.5
Instructions for the Level 3 operator (maintenance mode access) • 3.7
Instructions for the Level 4 operator (service mode access) • 3.10
QuickReference list • 3.11

QS1 Technical Reference Manual 3.1

Technical Manuals Online! - http://www.tech-man.com

 Operating instructions

Instructions for the Level 1 operator (public mode access)

Tasks that do not require you to log in

What is it you want to do This is how you do it

Silence the panel trouble buzzer Press Panel Silence.

Get a list of all the active points on a 1. Press Status.

panel
2. Choose All Active to get a list of all the active points.
Choose Alarm to get a list of only the active alarm points.
Choose Supervisory to get a list of only the active
supervisory points.
Choose Monitor to get a list of only the active monitor
points.
3. Press DEL to backspace the cursor then enter the panel
number.
4. Choose Display to view the list on the CPU/Display unit.
— or —
Choose Printer to print the list.

Identify points that are in trouble 1. Press Status.

2. Choose Trouble
3. Press DEL to backspace the cursor then enter the panel
number.
4. Choose Display to view the list on the CPU/Display unit.
— or —
Choose Printer to print the list.

Identify active points in a Service 1. Press Status.

Group that is being tested
2. Choose Test.
3. Press DEL to backspace the cursor then enter the panel
number.
4. Choose Display to view the list on the CPU/Display unit.
— or —
Choose Printer to print the list.

3.2 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Operating instructions

Tasks that do not require you to log in

What is it you want to do This is how you do it

Identify points that are disabled 1. Press Status.

2. Choose Disabled Pts.
3. Press DEL to backspace the cursor then enter the panel
number.
4. Choose Display to view the list on the CPU/Display unit.
— or —
Choose Printer to print the list.

Identify output devices that are 1. Press Status.

turned on
2. Choose Outputs
3. Press DEL to backspace the cursor then enter the panel
number.
4. Choose Display to view the list on the CPU/Display unit.
— or —
Choose Printer to print the list.

Verify power supply voltage levels 1. Press Status.

2. Choose Internal
3. Press Enter.
4. Choose Display to view the list on the CPU/Display unit.
— or —
Choose Printer to print the list.

Get a list of smoke detectors that 1. Press Menu.

require servicing (DIRTY attribute
2. Choose Reports > Maintenance > Dirty>80%.
greater than 80%)
3 Enter the panel number.
4. Choose Display to view the list on the CPU/Display unit.
— or —
Choose Printer to print the list.

QS1 Technical Reference Manual 3.3

Technical Manuals Online! - http://www.tech-man.com

 Operating instructions

Tasks that do not require you to log in

What is it you want to do This is how you do it

Get a list of smoke detectors that 1. Press Menu.

may require servicing (DIRTY
2. Choose Reports > Maintenance > Dirty>20%.
attribute greater than 20%)
3 Enter the panel number.
4. Choose Display to view the list on the CPU/Display unit.
— or —
Choose Printer to print the list.

Get the attributes for a single smoke 1. Press Menu.

detector
2. Choose Reports > Maintenance > Single Device.
3. Enter the panel number.
4. Choose Display to view the list on the CPU/Display unit.
— or —
Choose Printer to print the list.

Get the attributes for every smoke 1. Press Menu.

detector on a single SLIC
2. Choose Reports > Maintenance > Card Devices.
3 Enter the panel number.
4. Choose Display to view the list on the CPU/Display unit.
— or —
Choose Printer to print the list.

Perform a lamp test 1. Press Menu.

2. Choose Test > Lamp Test.

3.4 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Operating instructions

Instructions for the Level 2 operator (emergency mode access)

Tasks that require you to log on as a Level 2 operator

What is it you want to do This is how you do it

Log onto the panel as a Level 2 Turn the Enable Controls key 1/4 of a turn clockwise.
operator
— or —
1. Press Menu.
2. Choose Login then enter the password required for Level 2
access.

Reset the panel Press System Reset.

Turn off alarm signaling circuits Press Alarm Silence.

when the panel is in alarm (Alarm
Silence)

Turn on alarm signaling circuits Press Drill then Enter.

when the panel is not in alarm (Drill)

Get a list of all events processed on 1. Press Menu.

a panel
2. Choose Reports > History.
3. Enter the panel number.
4. Choose Display to view the list on the CPU/Display unit.
— or —
Choose Printer to print the list.

Change the password required for 1. Press Menu.

Level 1 access
2. Choose Program > Edit Password > Level 1.
3. Enter the new password.

Switch automatic detectors to their 1. Press Menu.

alternate sensitivity settings
2. Choose Activate > Alt Sens.

Switch automatic detectors to their 1. Press Menu.

primary sensitivity settings
2. Choose Restore > Prm Sens.

QS1 Technical Reference Manual 3.5

Technical Manuals Online! - http://www.tech-man.com

 Operating instructions

Tasks that require you to log on as a Level 2 operator

What is it you want to do This is how you do it

Distribute event records according 1. Press Menu.

to their alternate message routing
2. Choose Activate > Alt Msg Route.

Distribute event records according 1. Press Menu.

to their primary message routing
2. Choose Restore > Prm Msg Route.

Disable a Zone 1. Press Menu.

2. Choose Disable > Zone.
3. Select a Zone from the pick list then press Enter.

Enable a Zone 1. Press Menu.

2. Choose Enable > Zone.
3. Select a Zone from the pick list then press Enter.

Disable a device 1. Press Menu.

2. Choose Disable > Device.
3. Enter the device address, where:
PP is the panel number (01)
CC is the card number
DDD is the circuit or device number

Enable a device 1. Press Menu.

2. Choose Enable > Device.
3. Enter the device address, where:
PP is the panel number (01)
CC is the card number
DDD is the circuit or device number

3.6 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Operating instructions

Instructions for the Level 3 operator (maintenance mode access)

Tasks that require you to log on as a Level 3 operator

What is it you want to do This is how you do it

Log onto the panel as a Level 3 1. Press Menu.

operator
2. Choose Login then enter the password required for Level 3
access.

Change the password required for 1. From the Main Menu, select Program.
Level 2 access
2. Select Edit Password.
3. Select Level 2 then enter the new password.

Get a list of all the hardware and 1. Press Menu.

software components installed on a
2. Choose Reports > Revision.
panel and their revision levels
3. Enter the panel number.
4. Choose Display to view the list on the CPU/Display unit.
— or —
Choose Printer to print the list.

Set the system time and date 1. Press Menu.

2. Choose Program > Time/Date.
3. Choose Enter Time, then press DEL until the display shows
HHMMSS.
Enter the time in 24–hour format where HH is the hour, MM
is the minutes, and SS is the seconds.
Example: To set the time for 1:00 p.m., enter 130000.
4. Select Enter Date.
Enter the date where MM is the number of the month, DD is
the date, and YYYY is the year.
Example: To set the date for January 1, 2001, enter
01012001.

QS1 Technical Reference Manual 3.7

Technical Manuals Online! - http://www.tech-man.com

 Operating instructions

Tasks that require you to log on as a Level 3 operator

What is it you want to do This is how you do it

Turn on an output circuit 1. Press Menu.

Note: A typical system may assign 2. Choose Activate > Output.
manual override functions a high
3. Enter the output circuit's address, where PP is the panel
priority level, alert responses a low
number, CC is the card number, and DDD is the circuit
priority, and alarm responses a
number.
medium priority.
4. Choose Steady to change the circuit's output to always on
Choose 20 BPM to change the circuit's output to a 20 beat
per minute signal rate (On = 2–1/2 s; Off = 2–1/2 s).
Choose 120 BPM to change the circuit's output to a 120
beat per minute signal rate (On = 1/4 s; Off = 1/4 s).
Choose Temporal to change the circuit's output to a 3–3–3
pattern.
5. Choose High Priority.

Turn off an output circuit 1. Press Menu.

2. Choose Restore > Output.
3. Enter the output circuit's address, where PP is the panel
number, CC is the card number, and DDD is the circuit
number.
4. Choose Off.

Turn an LED on 1. Press Menu.

2. Choose Activate > LED.
3. Choose one of the following:
Steady to turn the LED on
Fast Blink to have the LED flash at a fast rate
Slow Blink to have the LED flash at a slow rate
4. Enter the LED's address where GG is the group number,
SS is the switch number, and L is the LED number.

Turn an LED off 1. Press Menu.

2. Choose Restore > LED.
3. Choose Off
4. Enter the LED's address where GG is the group number,
SS is the switch number, and L is the LED number.

3.8 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Operating instructions

Tasks that require you to log on as a Level 3 operator

What is it you want to do This is how you do it

Disable or enable an And Group, 1. Press Menu.

Matrix Group, or Time Control
2. Choose Disable or Enable.
3. Choose And if an And group, Matrix if a Matrix group, or
Time Control if a time control.
4. Pick a group from the appropriate list and press Enter.

Disable or enable a switch on a zone 1. Press Menu.

display
2. Choose Disable > Switch.
— or —
Enable > Switch.
3. Enter the switch address, where GG is the group number,
and SS is the switch number.

Disable or enable the mapping 1. Press Menu.

function on an SLIC
2. Choose Disable > Loop Mapping.
— or —
Enable > Loop Mapping.
3. Enter the card address for the SLIC.

Start a Service Group test 1. Press Menu.

2. Choose Test > Start Test.
3. Select a Service group from the pick list and press Enter.

Cancel a Service Group test 1. Press Menu.

Note: The panel automatically resets 2. Choose Test > Cancel Test.
after you cancel a test.
2. Select a Service group from the pick list and press Enter.

QS1 Technical Reference Manual 3.9

Technical Manuals Online! - http://www.tech-man.com

 Operating instructions

Instructions for the Level 4 operator (service mode access)

What is it you want to do This is how you do it

Log onto the panel as a Level 4 1. Press Menu.

operator
2. Choose Login then enter the password required for Level 4
access.

Change the password required for 1. Press Menu.

Level 3 access
2. Choose Program > Edit Password > Edit Password
3. Choose Level 3 then enter the new password.

Change the password required for 1. Press Menu.

Level 4 access
2. Choose Program > Edit Password > Edit Password
3. Choose Level 4 then enter the new password.

Restart a panel 1. Press Menu.

2. Choose Program > Restart > Panel
3. Enter the panel's address.

Reset the alarm history counter 1. From the Main Menu, select Program.
2. Select Reset.
3. Enter the panel's address.

3.10 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Operating instructions

QuickReference list
Required access level
What is it you want to do L1 L2 L3 L4
Change smoke detector sensitivity settings to their alternate values ü ü ü
Change smoke detector sensitivity settings to their primary values ü ü ü
Change the current state of an LED (manual override) ü ü
Change the current state of an output circuit (manual override) ü ü
Change the password required for Level 1 access ü ü ü
Change the password required for Level 2 access ü ü
Change the password required for Level 3 access ü
Change the password required for Level 4 access ü
Disable or enable a device ü ü ü
Disable or enable a switch on a zone display ü ü
Disable or enable a zone ü ü ü
Disable or enable all the devices on a single card ü
Disable or enable an And Group, Matrix Group, or Time Control ü ü
Disable or enable the mapping function on an SLIC ü ü
Get a list of all the active points on a panel ü ü ü ü
Get a list of all the hardware and software components installed on a ü ü
panel and their revision levels
Get a list of smoke detectors that may require servicing (DIRTY attribute ü ü ü ü
greater than 20%)
Get a list of smoke detectors that require servicing (DIRTY attribute ü ü ü ü
greater than 80%)
Get the attributes for a single smoke detector ü ü ü ü
Get the attributes for all the smoke detectors on a single SLIC ü ü ü ü
Identify output devices that are turned on ü ü ü ü
Identify active points in a Service Group that is being tested ü ü ü ü
Identify points that are disabled ü ü ü ü
Identify points that are in their active state ü ü ü ü
Identify points that are in trouble ü ü ü ü
Log onto the panel as a Level 2 operator ü ü ü
Log onto the panel as a Level 3 operator ü ü
Log onto the panel as a Level 4 operator ü
Perform a lamp test ü ü ü ü

QS1 Technical Reference Manual 3.11

Technical Manuals Online! - http://www.tech-man.com

 Operating instructions

Required access level

What is it you want to do L1 L2 L3 L4
Reset the alarm history counter ü
Reset the panel ü ü ü
Restart the panel ü
Restore an LED to its previous state ü ü
Restore an output circuit to its previous state ü ü
Route off-normal signals to the alternate set of panels used to post ü ü ü
messages
Route off-normal signals to the primary set of panels used to post ü ü ü
messages
Set the system time and date ü ü
Silence the panel trouble buzzer ü ü ü ü
Start a Service Group test ü ü
Cancel a Service Group test ü ü
Turn off alarm signaling circuits when the panel is in alarm (Alarm ü ü ü
Silence)
Turn on alarm signaling circuits when the panel is not in alarm (Drill) ü ü ü
Verify power supply voltage levels ü ü ü ü

3.12 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Chapter 4
Programming instructions

Summary
This chapter provides instructions for programming the fire alarm system
from the front panel. Worksheets are provided at the end of the chapter
to use as programming aids and to document the system programming.

Content
Overview • 4.2
QuickStart setup instructions • 4.4
Customizing the system configuration • 4.12
Setting up an Output Group • 4.19
Setting up a Zone • 4.22

QS1 Technical Reference Manual 4.1

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Overview

What is a Zone? A Zone is a function in the system software that initiates an

active response based on a single alarm event. Firewall
designations, planned evacuation criteria, architectural design,
and other factors all contribute to how the system designer
divides the protected premises into zones.

ZONE 1
FACP

ZONE 2 ZONE 3
J

What is an Output Group? An Output Group is a function in the system software that
establishes the correlation between input circuits and
responses. When an input changes states, the condition of the
input determines which response the panel runs. For example,
a smoke detector initiates the Active response when it signals
an alarm condition but initiates the Trouble response when
removed from its base.

Output 1

ZONE 1
Active

Trouble

Output 2

Active

Trouble

4.2 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Table 4-1: Programmable features

Front Panel Programming Configuration Utility

Feature (FPP) (CU)

And Groups No Yes

Output Groups Yes Yes
Matrix Groups No Yes
Service Groups Limited Yes
Time Controls No Yes
Zones Yes Yes
LED Configure Limited Yes
Switch Configure Limited Yes
SIGA - Prealarm Yes Yes
SIGA - Sensitivity levels Yes Yes
Alarm Verification Yes Yes
Coded Operation Yes Yes
Custom Messages Yes (requires bar code wand) Yes
Message Routing No Yes
SIGA - Diagnostics No Yes
AC Delay No Yes
Two-stage Operation No Yes
General Alarm Inhibit No Yes
Market Place No Yes
Card Configuration Yes Yes
Language No Yes
Zone Resound Inhibit No Yes
Drill Programming No Yes
Alarm Silence Programming No Yes
Waterflow Silence No Yes
Supervisory Duct No Yes
Enable Trouble Reminder No Yes
Auto Alarm Signal Silence No Yes
Alarm Signal Silence/Reset Inhibit Yes Yes
Panel Silence Resound Time No Yes
SIGA–REL No Yes

QS1 Technical Reference Manual 4.3

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

QuickStart setup instructions

Step 1: This procedure uses the AutoLearn and AutoLoop utilities to

Read this before proceeding automatically configure the system. The AutoLearn utility
configures the option cards. The AutoLoop utility configures
the circuits on the Signature loop.
Note: If at any time you get an
Exception Event while programming Caution: Running the AutoLearn utility deletes the existing
the system, note the error code, and panel programming. If you have already programmed the
then contact EST Technical Services system, running AutoLearn requires you to re-enter everything
at 6411 Parkland Drive, Sarasota, FL, again from the beginning.
34243 or at 1-800-655-4497.
To clear the Exception Event, press If you have a dialer installed, the AutoLearn utility requires you
Alarm Silence while the event is to program the DLD before exiting. Be sure to have the
displayed. You may have to reset the following:
panel to display the event again. • Subscriber account numbers, telephone numbers, and
transmission formats obtained from the CMS (Central
Monitoring Station). Appendic C provides a list of Contact ID
event codes.
• A completed copy of the DLD Programming Worksheet
(Figure 4-1).
After you have finished using the AutoLearn and AutoLoop
utilities to configure the system, you can either:
• Customize the system programming
• Go to step 11 and Save and Sync.

Step 2: 1. Verify that each circuit card installed in the control panel
Apply power to the system has a unique card address.
2. Apply power to the control panel and to all the remote
annunciators.
After applying power, the panel CPU performs a diagnostic
check in the background. You can not begin programming
until this finishes and the AutoLearn option becomes
available.

4.4 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Step 3: On each remote annunciator panel:

Assign Panel ID numbers to 1. Press Menu.
the remote annunciator panels 2. Choose Login then enter the password required for Level 4
access (default is 4444).
3. Choose Program > Configure > AutoLearn.
4. Press Del twice then enter an unused Panel ID from 02 to
09 (01 is reserved for the control panel).
5. Enter the number of panels that are connected to the
RS485 riser, including the control panel. This is your
maximum number of panel addresses.
6. Select the wiring configuration of the RS485 riser (Class A
or Class B) then press Enter.
Note: The wiring configuration must be the same for all
panels.

Step 4: On the control panel:

AutoLearn the control panel. 1. Press Menu.
Note: Before running the AutoLearn 2. Choose Login then enter the password required for Level 4
utility, make sure you have not access (default is 4444).
installed more cards than the system
allows. 3. Choose Reports > Revision > Enter > Display. Verify all the
cards installed in the cabinet appear in the list.
4. Press Menu then choose Program > Configure >
AutoLearn.
5. Enter 01 for the Panel ID.
6. Enter the number of panels that are connected to the
RS485 riser, including the control panel. This is your
maximum number of panel addresses.
7. Select the wiring configuration of the RS485 riser (Class A
or Class B) then press Enter.
If you do not have a DLD card installed, the system will
automatically reboot after the AutoLearn utility configures the
system. Go to step 10.
If you do have a DLD card installed, go to step 5.

QS1 Technical Reference Manual 4.5

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Step 5: 1. Choose #'s of CMS then choose the number of CMS

Set up the receiver call-in receivers that the DLD may dial into over the public
switched telephone network.
numbers and retry attempts
2. Choose CMS Phone # then enter the telephone numbers
of the CMS receivers:
§ Choose Rcvr 1 Prim # then enter the first number to try
for the first CMS receiver.
§ Choose Rcvr 1 Sec # then enter the second number to
try for the first CMS receiver.
§ Choose Rcvr 2 Prim # then enter the first number to try
for the second CMS receiver.
§ Choose Rcvr 2 Sec # then enter the second number to
try for the second CMS receiver.
§ Choose Exit.
3. Choose Retry Count then enter the number of times you
want the dialer to attempt to contact the CMS receiver.

Step 6: 1. Choose Accounts then <New> to set up a new account

Set up the subscriber — or —
accounts Select an account number then press Enter.
2. Choose Account # then enter the number of the subscriber
account.
3. Choose Formats then choose the required transmission
format.
4. Choose Test–Normal then enter the character string to
send when the control panel is normal.
5. Choose Test–Abnormal then enter the character string to
send when the control panel is off-normal.
6. Choose Test Time then enter when you want the dialer to
transmit the test string in 24-hour format.
7. Choose CMS then choose which CMS receiver to dial.
This is the receiver that holds the account.
8. Choose Exit.

4.6 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Step 7: 1. Choose Default Msgs > Alarm.

Edit the default alarm 2. Choose Account then select the subscriber account you
messages want to receive the message.
Note: The dialer automatically sends 3. Choose Active Msg then enter the message you want sent
the default alarm message for active for alarm activation events.
alarm inputs that are not programmed
For example, for Contact ID enter 111000000
to initiate a dialer response.
4. Choose Restore Msg then enter the message you want
sent for alarm restoration event.
For example, for Contact ID enter 311000000
5. Choose Exit.

Step 8: 1. Choose Default Msgs > Trouble.

Edit the default trouble 2. Choose Account then select the subscriber account you
messages want to receive the message.
Note: The dialer automatically sends 3. Choose Active Msg then enter the message you want sent
the default trouble message for inputs for trouble activation events.
that signal a trouble but are not
For example, for Contact ID enter 130000000
programmed to initiate a dialer
response. 4. Choose Restore Msg then enter the message you want
sent for trouble restoration event.
For example, for Contact ID enter 330000000
5. Choose Exit.

Step 9: 1. Choose Default Msgs > Supervisory.

Edit the default supervisory 2. Choose Account then select the subscriber account you
messages want to receive the message.
Note: The dialer automatically sends 3. Choose Active Msg then enter the message you want sent
the default supervisory message for for supervisory activation events.
active supervisory inputs that are not
For example, for Contact ID enter 120000000
programmed to initiate a dialer
response. 4. Choose Restore Msg then enter the message you want
sent for a supervisory restoration event.
For example, for Contact ID enter 220000000
5. Choose Exit.

QS1 Technical Reference Manual 4.7

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Step 10: Run the AutoLoop utility on each loop controller installed in
AutoLoop the loop controller the control panel.
cards
Caution: When the system reboots, the loop controller
reinitializes the loop. If you attempt to run the AutoLoop utility
during this time, you could corrupt the project database.

1. On the control panel, press Menu.

2. Choose Login then enter the password required for Level 4
access.
3. Choose Program > Configure.
If the loop is still initializing, do not proceed until loop
initialization has finished.
4. Choose Cards > Edit, then enter the card number for the
loop controller.
5. On the Edit Cards menu, choose AutoLoop.
6. If the number of detector and module addresses on the
display match the number installed on the loop, press
Enter to accept, then wait while the database is updated.
If not, press Del to cancel. You must correct the problem
before continuing with this loop.
7. On the SLIC menu, choose Exit.
8. For each additional loop controller, repeat steps 4–7.
9. Choose Exit.

Step 11: At this point, you have configured the project database for a
Saving the project database general alarm system. Refer to Table 4-2, Table 4-3, and
Table 4-4 for initial system settings.
Tip: Only Save and Sync after you
have finished programming the control If you want to accept the general alarm system configuration,
panel and you want to update the choose Save and Sync.
project databases in the remote If you want to make changes to the system configuration,
annunciators. choose Save, and then make your changes. See Customizing
the system configuration. After making all of your changes:
1. Press Menu.
2. Choose Login then enter the password required for Level 4
access.
3. Choose Program > Configure > Exit.
4. Choose Save and Sync.
Note: If the local AHJ requires a hard copy of your site
programming, use the QuickStart Configuration Utility to
retrieve the database from the panel and print the required
information.

4.8 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Table 4-2: AutoLearn initial project settings

Option Value Description Edit?

Alarm Silence Audible only Turns off Audible and Common Alarm Output circuits CU
when someone presses Alarm Silence.
Drill Audible only Turns off Audible and Common Alarm Output circuits CU
when someone presses Drill.
Drill Activation Type Steady The Drill signal is a constant signal. CU
Alarm Signal None Alarm Silence or Reset functions are not inhibited. You FPP/CU
Silence/Reset Inhibit can turn off (silence) notification circuits or reset the
panel any time after notification circuits are activated.
Buzzer Reminder Time Indefinitely The panel trouble buzzer remains silenced until the No
control panel processes a new off-normal signal.
AC Power Trouble 6h The panel will operate on battery power for 6 hours FPP/CU
Delay before signaling a trouble condition.
Two-stage Timer 0 s (UL) The panel will turn on notification circuits immediately CU
300 s (ULC) after processing an alarm signal (UL) or after 5 minutes
(ULC).
Zone Resound Inhibit No Turn silenced NAC circuits back on if an active alarm No
input circuit remains in the active condition after
resetting the panel.
Primary Routing All Cabinets Distribute event records to all panels in the system CU
when primary routing is activated.
Alternate Routing All Cabinets Distribute event records to all panels in the system CU
when alternate routing is activated.
Language English (U.S.) U.S. English displayed on CPU/Display. No
Relay 1 Type Alarm Alarm events cause the contact positions of Relay 1 on No
the PS6 to change positions.
Relay 2 Type Supervisory Supervisory events cause the contact positions of Relay No
2 on the PS6 to change positions.
Relay 3 Type Trouble Trouble events cause the contact positions of Relay 3 No
on the PS6 to change positions.
Relay 4 Type Monitor Monitor events cause the contact positions of Relay 4 CU
on the PS6 to change positions.

QS1 Technical Reference Manual 4.9

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Table 4-3: AutoLearn initial card configuration settings

Card Circuit Address Device type Edit? Diagram

SLIC NAC 1 270 Visible FPP/CU

NAC 2 271 Common Alarm FPP/CU
Output
NAC 1 NAC 2

4.10 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Table 4-4: AutoLoop initial settings for SIGA devices

SIGA Device Personality Description Device Type Edit?

SIGA–IPHS, –PHS, none Smoke detector settings as follows: Alarm FPP/CU

–PS, –IS Sensitivity: Least
Verification: None
Prealarm: None
SIGA–HFS, HRS, none Heat detector settings not programmable Alarm FPP/CU
–IM
Single-stage pull 01 Class B Alarm Latching Pull FPP/CU
stations
Dual-stage pull 01 Class B Alarm Latching Monitor FPP/CU
stations
01 Class B Alarm Latching Pull FPP/CU
SIGA–APS 03 Class B Active Non-Latching Monitor FPP/CU
03 Class B Active Non-Latching Monitor FPP/CU
SIGA–(M)CC1(S) 05 Riser selector Common Alarm FPP/CU
Output
SIGA–(M)CC2 07 Dual riser selector Common Alarm FPP/CU
Output
SIGA–(M)CR(R) 08 Dry contact Nonsupervised FPP/CU
Output
SIGA–(M)CT1 01 Class B Alarm Latching Alarm FPP/CU
SIGA–(M)CT2 01 Class B Alarm Latching Alarm FPP/CU
01 Class B Alarm Latching Alarm FPP/CU
SIGA–DTS 01 Class B Alarm Latching Alarm FPP/CU
SIGA–IO 31 Monitor Input/Output N.O. Monitor FPP/CU
SIGA–MAB 00 Class A Signal Output Monitor FPP/CU
00 not used
SIGA–UM 00 Class A Signal Output Monitor FPP/CU
00 not used
SIGA–MM1 03 Class B Active Non-Latching Monitor FPP/CU
SIGA–WTM 02 Class B Active Latching - Delayed Alarm FPP/CU
04 Class B Active Latching. Supervisory FPP/CU
SIGA–(M)RM1 23 Riser monitor - 24 Vdc Monitor FPP/CU

Note: If you use Signature devices from another system, the AutoLoop utility uses the attributes programmed from
the previous system as the initial settings for a general alarm system.

QS1 Technical Reference Manual 4.11

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Customizing the system configuration

You can customize the system configuration, if

your requirements exceed that of the general WARNING: Entering Edit mode (choosing
alarm system created using the AutoLearn and Configure on the Program menu) disables the
AutoLoop utilities. control panel and leaves the premises unprotected
until you exit Edit mode.
Before you can make any changes to the system
programming, you must log onto the system to
start an editing session. To start an editing session:
The control panel has a watchdog timer that kicks 1. Press Menu.
you out of an editing session after a period of 2. Choose Login then enter the password required
inactivity. If this happens, you will have to log in for Level 4 access.
again to continue.
3. Choose Program > Configure.
After you finish customizing the system
configuration, save your changes, and then test
the system. After everything checks out then Save
and Sync to copy the database to the remote
annunciators.

What is it you want to do This is how you do it

Make information about the installer available 1. On the Configure menu, choose System > User
on the CPU/Display Labels.
AutoLearn default: No text 2. Choose Facility Name, scan in the name of the
project, and then press Enter.
3. Choose Inst Company, scan in the name of the
installing company, and then press Enter.
4. Choose Phone Number, scan in the telephone
number to call for service-related issues, and
then press Enter.
5. Choose Programmer, scan in the name of the
person that programmed the system, and then
press Enter.
6. Choose Exit.

Set how long notification circuits must stay on 1. On the Configure menu, choose System >
before pressing Alarm Silence can turn them ALM/RST Inhib.
off or pressing Reset can reset the panel
2. Select a time delay from the pick list then press
AutoLearn default: None (no delay) Enter.

Set how long the panel must wait before 1. On the Configure menu, choose System > AC
signaling an ac power failure Power Dly.
AutoLearn default: 0 (no delay) 2. Select a time delay from the pick list then press
Enter.

4.12 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

What is it you want to do This is how you do it

Change the device type of the NAC circuits on

the SLIC. WARNING: Changing an output circuit from a
Common Alarm Output device type to an Audible
AutoLearn defaults: NAC1 device type is Visible; device type does not automatically place the
NAC 2 device type is Common Alarm Output Audible circuit in an Output Group. You must add
Common Alarm Output circuits turn on the Audible Circuit to the Output Group manually
automatically when an input signals an alarm or the Audible circuit will not turn on.
event. Visible and Audible output circuits must be
placed in an Output Group in order to turn them 1. On the Configure menu, choose Cards > Edit
on. The AutoLearn utility automatically places then enter the card address number.
Visible circuits in an Output Group
2. Choose Config Card.
3. Choose NAC 1 then choose the device type for
NAC 1.
4. Choose NAC 2 then choose the device type for
NAC 2.
5. Choose Exit > Save Edits, then wait while the
database is updated.

Change the performance class of the Signature 1. On the Configure menu, choose Cards > Edit
loop wiring then enter the card address number.
AutoLearn default: Wiring is Class B. 2. Choose Config Card.
3. Choose Wiring Class then choose how the loop
is wired to the SLIC.
4. Choose Exit > Save Edits, then wait while the
database is updated.

Enter location message text for an automatic 1. On the Configure menu, choose Cards > Edit
detector and then enter the card address number of the
loop controller.
2. Choose Config Detect > Edit > Enter Serial #
and then scan or enter the detector's serial
number.
3. Choose Message then scan in the text that you
want sent when the detector signals an event.
4. Choose Exit > Save Edits.

QS1 Technical Reference Manual 4.13

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

What is it you want to do This is how you do it

Change the Alarm Sensitivity setting of a

smoke detector WARNING: Selection of the appropriate detector
technology and sensitivity settings should result
from a careful analysis of the hazard,
environmental conditions, and expected results.

1. On the Configure menu, choose Cards > Edit

and then enter the card address number of the
loop controller.
2. Choose Config Detect > Edit > Enter Serial #
and then scan or enter the detector's serial
number.
3. Choose Sensitivity then choose the alarm
sensitivity setting you want the detector to use.
Refer to Table 4-5 and Table 4-6.
4. Choose Exit > Save Edits.

Change the Alarm Verification setting of a 1. On the Configure menu, choose Cards > Edit
smoke detector and then enter the card address number of the
loop controller.
2. Choose Config Detect > Edit > Enter Serial #
and then scan or enter the detector's serial
number.
3. Choose Verification then choose the length of
the alarm verification period.
4. Choose Exit > Save Edits.

Change the Prealarm setting of a smoke

detector WARNING: Prealarm obscuration levels below
80% should not be used without full knowledge of
the possible consequences.

1. On the Configure menu, choose Cards > Edit

and then enter the card address number of the
loop controller.
2. Choose Config Detect > Edit > Enter Serial #
and then scan or enter the serial number of the
detector.
3. Choose Pre-Alarm then choose the warning
threshold setting you want the detector to use.
Refer to Table 4-5 and Table 4-6.
4. Choose Exit > Save Edits.

4.14 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Table 4-5: %Obscuration levels for SIGA–IPHS, SIGA–PS, and SIGA–PHS

Alarm Obscuration Levels
Sensitivity Settings Most More Normal Less Least
%Obscuration 1.00% 2.00% 2.50% 3.00% 3.50%
Prealarm Settings Prealarm Obscuration Levels
95% 0.95% 1.90% 2.38% 2.85% 3.33%
90% 0.90% 1.80% 2.25% 2.70% 3.15%
85% 0.85% 1.70% 2.13% 2.55% 2.98%
80% 0.80% 1.60% 2.00% 2.40% 2.80%
75% 0.75% 1.50% 1.88% 2.25% 2.63%
70% 0.70% 1.40% 1.75% 2.10% 2.45%
65% 0.65% 1.30% 1.63% 1.95% 2.28%
60% 0.60% 1.20% 1.50% 1.80% 2.10%
55% 0.55% 1.10% 1.38% 1.65% 1.93%
50% 0.50% 1.00% 1.25% 1.50% 1.75%
45% 0.45% 0.90% 1.13% 1.35% 1.58%
40% 0.40% 0.80% 1.00% 1.20% 1.40%
35% 0.35% 0.70% 0.88% 1.05% 1.23%
30% 0.30% 0.60% 0.75% 0.90% 1.05%
25% 0.25% 0.50% 0.13% 0.31% 0.88%
20% 0.20% 0.40% 0.50% 0.60% 0.70%
15% 0.15% 0.30% 0.38% 0.45% 0.53%
10% 0.10 0.20% 0.25% 0.30% 0.35%
5% 0.05 0.10% 0.13% 0.15% 0.18%
Note: Shaded prealarm settings not available for SIGA–IPHS

Table 4-6: %Obscuration levels for SIGA–IS

Alarm Obscuration Levels
Sensitivity Settings Most More Normal Less Least
%Obscuration 0.7% 1.00% 1.20% 1.40% 1.6%
Prealarm Settings Prealarm Obscuration Levels
95% 0.67% 0.95% 1.14% 1.33% 1.52%
90% 0.63% 0.90% 1.08% 1.26% 1.44%
85% 0.60% 0.85% 1.02% 1.19% 1.36%
80% 0.56% 0.80% 0.96% 1.12% 1.28%
75% 0.53% 0.75% 0.90% 1.05% 1.20%
70% 0.49% 0.70% 0.84% 0.98% 1.12%
65% 0.46% 0.65% 0.78% 0.91% 1.04%
60% 0.42% 0.60% 0.72% 0.84% 0.96%
55% 0.39% 0.55% 0.66% 0.77% 0.88%
50% 0.35% 0.50% 0.60% 0.70% 0.80%

QS1 Technical Reference Manual 4.15

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

What is it you want to do This is how you do it

Enter location message text for a circuit on a 1. On the Configure menu, choose Cards > Edit
SIGA module and then enter the card address number of the
loop controller.
2. Choose Config Module > Edit > Enter Serial #
and then scan or enter the serial number of the
module.
3. For a single-address module or the first
address of a dual-address module, choose
Device 1.
— or —
For the second address of a dual-address
module, choose Device 2.
4. Choose Message, scan in the text, and then
press Enter.
5. Choose Exit.

Change the device type for a circuit on a SIGA 1. On the Configure menu, choose Cards > Edit
module and then enter the card address number of the
loop controller.
Note: The device types shown in the pick lists vary
depending on the SIGA module. The device types 2. Choose Config Module > Edit > Enter Serial #
shown in the pick lists for the second address of a and then scan or enter the serial number of the
dual-address module also vary depending on the module.
device type chosen for the first address.
3. For a single-address module or the first
address of a dual-address module, choose
Device 1.
— or —
For the second address of a dual-address
module, choose Device 2.
4. Choose Type, select a device type from the
pick list, and then press Enter.
5. Choose Exit.

4.16 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

What is it you want to do This is how you do it

Change the personality code for a circuit on a 1. On the Configure menu, choose Cards > Edit
SIGA module and then enter the card address number of the
loop controller.
Note: The personality codes shown in the pick lists
vary depending on the SIGA module and the 2. Choose Config Module > Edit > Enter Serial #
chosen device type. and then scan or enter the serial number of the
module.
3. For a single-address module or the first
address of a dual-address module, choose
Device 1.
— or —
For the second address of a dual-address
module, choose Device 2.
4. Choose Personality, select a personality code
from the pick list, and then press Enter.
5. Choose Exit.

Enable the loop controller mapping function 1. Press Menu.

AutoLearn default: Mapping disabled 2. Log onto the panel as a Level 4 operator.
3. Choose Enable > Loop Mapping.
4. Enter the card number of the SLIC that
connects to the device you want to replace.
Wait until mapping finishes before continuing.
5. Choose Cards > Edit.
6. Enter the card number of the SLIC that
connects to the device you want to replace.
7. Choose Accept Map.
If actual and expected data for detectors and
modules are the same, press Enter.
8. Choose Exit > Exit > Save.

QS1 Technical Reference Manual 4.17

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Table 4-7: Device type descriptions

Alarm Device type assigned to IDC circuits that connect to automatic or a combination of automatic
and manual alarm-signal initiating devices. Alarm circuits signal Alarm Active events.
Alarm Output Device type assigned to IDC/NAC circuits that connect to notification appliances that you want
turned on automatically when the panel processes an alarm signal. Alarm Output circuits turn
off when you press Alarm Silence and turn on when you press Drill.
Audible Device type assigned to IDC/NAC circuits that connect to audible notification appliances
(horns). Audible circuits turn off when you press Alarm Silence and turn on when you press
Drill.
Heat Device type assigned to IDC circuits that connect to automatic alarm-signal initiating devices
that detect a rise in the surrounding temperature. Heat circuits signal Heat Alarm events.
Monitor Device type assigned to IDC circuits that connect to monitor-signal initiating devices that
monitor the operation of ancillary system functions. Monitor circuits signal Monitor events.
Output Device type assigned to IDC/NAC circuits that supervise their output wiring for opens and
shorts. Output circuits do not turn off when you press Alarm Silence or turn on when you press
Drill.
Pull Device type assigned to IDC circuits that connect to manually operated alarm-signal initiating
devices. Pull circuits signal Pull Station events.
Supervisory Device type assigned to IDC circuits that connect to supervisory-signal initiating devices that
detect abnormal conditions that could make the sprinkler system inoperative or ineffective.
Supervisory circuits signal Supervisory events.
Tamper Device type assigned to IDC circuits that connect to supervisory-signal initiating devices that
detect when someone tampers with a component of the sprinkler system. Tamper circuits signal
Tamper events.
Verified Smoke Device type assigned to IDC circuits that connect to automatic alarm-signal initiating devices
that use alarm verification. Verified Smoke circuits signal Alarm Verify events when the fire
condition is first detected then Alarm Active events after verifying the fire condition exists.
Visible Device type assigned to IDC/NAC circuits that connect to visual notification appliances
(strobes). Visible circuits do not turn off when you press Alarm Silence or turn on when you
press Drill unless programmed to do so.
Water Flow Device type assigned to IDC circuits that connect to alarm-signal initiating devices that detect
water flowing through the sprinkler system. Water Flow circuits signal Waterflow events.

4.18 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Setting up an Output Group

Before you begin Before you begin, you should complete an Output Group
Programming Worksheet (Figure 4-6) for each Output group.
Keep a copy for your records.

To set up an Output Group:

1. On the control panel, press Menu.
2. Choose Login then enter the password required for Level 4
access.
3. Choose Program > Configure > Output.
4. To program a new Output group, choose Add.
— or —
To edit an existing Output group, choose Edit, select the
group from the pick list, and then press Enter.
5. Add the responses.
6. After you finish entering the responses, you should review
them to make sure they are correct.

Adding a response that activates an 1. Choose Responses.

output circuit
2. Choose Active or Trouble
3. Choose Add > Relay, then enter the circuit address where
CC is the card number and DDD is the circuit number.
4. Choose the activation setting.
5. Choose Exit > Save Edits.

Adding a response that activates a 1. Choose Responses.

delay
2. Choose Active or Trouble.
3. Choose Add > Delay.
4. Choose Delay Type, then choose when to initiate the delay
response.
5. Choose Delay Time, press Del four times, and then enter
how many seconds you want the delay to last.
6. Choose Exit > Save Edits.

QS1 Technical Reference Manual 4.19

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Adding a response that sends a 1. Choose Responses.

dialer string
2. Choose Active or Trouble.
3. Choose Add > Dialer.
4. Select an account number from the pick list, and then press
Enter.
5. Choose Send On, select when to send the dialer string from
the pick list, and then press Enter.
6. Choose Priority, select the priority classification from the
pick list, and then press Enter.
7. Choose String, then enter the message you want sent.
8. Choose Exit > Save Edits.

Reviewing your responses 1. Choose Review.

2. Choose Active to review the active responses.
— or —
Choose Trouble to review the trouble responses.

4.20 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Table 4-8: Response code definitions

Response Description

PppCccDddd 1234 This is what the panel display looks like when you review a response for an output
circuit.
P:pp C:cc D:ddd is the address of the of the output circuit (P = panel number, C =
card number, D = device number)
1 is the command direction (B = Both activation and restoration, A = Activation only,
R = Restoration only)
2 is the command (N = no operation, A = Activate, E = Enable, R = Restore, I =
Disable, D = Delay)
3 is the priority attribute (S = Set, A = Latch, L = Low, M = Medium, H = High)
4 is the command attribute (S = Set, R = Reset, W = 20 bpm, F = 120 bpm, T =
Temporal)

PppCccDddd 1234 This is what the panel display looks like when you review a response for an LED.
P:pp C:cc D:ddd is the address of the of the output circuit (P = panel number, C =
card number, D = device number)
1 is the command direction (B = Both activation and restoration, A = Activation only,
R = Restoration only)
2 is the command (N = no operation, A = Activate, E = Enable, R = Restore, I =
Disable, D = Delay)
3 is the priority attribute (S = Set, A = Latch, L = Low, M = Medium, H = High)
4 is the command attribute (S = Steady, R = Restore, W = Slow Blink, F = Fast
Blink)

Delay: ssss 1 This is what the panel display looks like when you review a response for delay.
ssss is the amount of delay in seconds
1 is the command direction (B = Both activation and restoration, A = Activation only,
R = Restoration only)

ACCT12QEEEGGPPP This is what the panel display looks like when you review a response for dialer
string.
— or —
ACCT is the 4-digit subscriber account number (0000–9999)
ACCT12PP
1 is the priority attribute (L = Life Safety, P = Property, S = System Integrity)
2 s the command direction (B = Both activation and restoration, A = Activation only,
R = Restoration only)
For Contact ID dialer strings:
Q is the event qualifier (1 = activation event, 3 = restoration event)
EEE is the event code. See Table 4-9.
GGPPP is the point being reported
For 4/2 dialer strings:
PP is the point being reported (00–99)

QS1 Technical Reference Manual 4.21

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Table 4-9: Contact ID Event Codes

100 – Medical alarm 155 – Foil break 350 and 360 – Communication
Trouble
101 – Pendant transmitter 156 – Day trouble
351 – Telco 1 fault
102 – Fail to report in 157 – Low bottled gas level
352 – Telco 2 fault
110– Fire Alarm 158 – High temperature
353 – Long range radio
111 – Smoke 159 – Low temperature
354 – Fail to communicate
112 – Combustion 161 – Loss of air flow
355 – Loss of radio supervision
113 – Water Flow 200 and 210 – Fire Supervisory
356 – Loss of central polling
114 – Heat 201 – Low water pressure
370 – Protection LoopTrouble
115 – Pull Station 202 – Low CO2
371 – Protection loop open
116 – Duct 203 – Gate valve sensor
372 – Protection loop short
117 – Flame 204 – Low water level
373 – Fire trouble
118 – Near alarm 205 – Pump activated
380 – Sensor Trouble
120 – Panic Alarm 206 – Pump failure
381 – Loss of supervisory (RF)
121 – Duress 300 and 310 – System Troubles
382 – Loss of supervisory (RPM)
122 – Silent 301 – AC loss
383 – Sensor tamper
123 – Audible 302 – Low system battery
384 – RF transmitter low battery
130 – Burglar Alarm 303 – RAM checksum bad
400 – Open/Close
131 – Perimeter 304 – ROM checksum bad
401 – Open/Close by user
132 – Interior 305 – System reset
402 – Group open/close
133 – 24 Hour 306 – Panel program changed
403 – Automatic open/close
134 – Entry/Exit 307 – Self–test failure
404 – Late to open/close
135 – Day/Night 308 – System shutdown
405 – Deferred open/close
136 – Outdoor 309 – Battery test failure
406 – Cancel
137 – Tamper 310 – Ground fault
407 – Remote arm/disarm
138 – Near alarm 320 – Sounder/Relay Trouble
408 – Quick arm
140 – General Alarm 321 – Bell 1
409 – Keyswitch open/close
141 – Polling loop open 322 – Bell 2
410 – Remote Access
142 – Polling loop short 323 – Alarm relay
411 – Call request made
143 – Expansion module failure 324 – Trouble relay
412 – Success – Download access
144 – Sensor tamper 325 – Reversing
413 – Unsuccessful access
145 – Expansion module failure 330 and 340 – System Peripheral
Trouble 414 – System shutdown
150 and 160 – 24-hour Non-
Burglary 331 – Polling loop open 415 – Dialer shutdown
151 – Gas detection 332 – Polling loop short
152 – Refrigeration 333 – Expansion module failure
153 – Loss of heat 334 – Repeater failure
154 – Water leakage 335 – Local printer paper out
336 – Local printer failure

4.22 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Table 4-9: Contact ID Event Codes (cont.)

420 – Access Control 600 – Test/Misc.
421 – Access denied 601 – Manual trigger test
422 – Access report by user 602 – Periodic test report
441 – Stay arming 603 – Periodic RF transmission
451 – Early opening/closing 604 – Fire test
452 – Late opening/closing 605 – Status report to follow
453 – Late to open 606 – Listen–in follow
454 – Late to close 607 – Walk Test mode
455 – Auto–arm failure 621 – Event Log reset
500 and 510 – System Disable 622 – Event Log 50% full
520 – Sounder/Relay Disable 623 – Event Log 90% full
521 – Bell 1 disable 624 – Event log overflow
522 – Bell 2 disable 625 – Time/Date reset
523 – Alarm relay disable 626 – Time/Date inaccurate
524 – Trouble relay disable 627 – Program mode entry
525 – Reversing relay disable 628 – Program mode exit
530 and 540 – System Peripheral 631 – Exception schedule change
Disable
550 and 560 – Communication
Disable
551 – Dialer disable
552 – Radio transmitter
570 – Disable Bypasses
570 – Zone bypass
571 – Fire zone bypass
572 – 24 Hour zone bypass
573 – Burglary zone bypass
574 – Group bypass

QS1 Technical Reference Manual 4.23

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Setting up a Zone

Before you begin Before you begin, you should complete a Zone Programming
Worksheet (Figure 4-7) for each Zone. Keep a copy for your
records. You will also need to refer to the Output Group
programming worksheets.

To set up a Zone:
1. On the control panel, press Menu.
2. Choose Login then enter the password required for Level 4
access.
3. Choose Program > Configure > Zone.
4. To program a new Zone, choose Add, and then choose a
zone type (Alarm, Supervisory, or Monitor).
— or —
Choose Edit, select an existing zone from the pick list, and
then press Enter.

Configure the Zone 1. Choose Message, scan in the message text, and then
press Enter.
2. Choose Members, then for each device that comprises the
Zone:
Choose Device Address, then enter the member's device
number from the worksheet
— or —
Choose Enter Serial#, scan in or enter the member's serial
number.
3. Choose Review to verify which devices you added to the
Zone. If you added any devices in error, delete them.
4. Choose Output Group > Add, then select the Output group
from the pick list that contains the responses you want
activated, and then press Enter.
Repeat for each Output group you want to add.
5. Choose Review to verify which Output groups you added to
the Zone. If you added any Output groups in error, remove
them.
6 For coded systems, choose Coding, and then enter the
Zone Code.

4.24 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Job Name: Page of

Panel: Card: 14

# of CMS receivers: ¨1 ¨2

CMS phone numbers: Receiver 1: #1) Receiver 1: #2)

Receiver 2: #1) Receiver 2: #2)

Retry Count: ¨ 5 ¨ 6 ¨ 7 ¨ 8 ¨ 9 ¨ 10

Account Number: Format: ¨ 4/2 ¨ Contact ID

Test strings: Panel normal: Panel off-normal:
Time: CMS receiver to dial: ¨ 1 ¨ 2

Account Number: Format: ¨ 4/2 ¨ Contact ID

Test strings: Panel normal: Panel off-normal:
Time: CMS receiver to dial: ¨ 1 ¨ 2

Account Number: Format: ¨ 4/2 ¨ Contact ID

Test strings: Panel normal: Panel off-normal:
Time: CMS receiver to dial: ¨ 1 ¨ 2

Account Number: Format: ¨ 4/2 ¨ Contact ID

Test strings: Panel normal: Panel off-normal:
Time: CMS receiver to dial: ¨ 1 ¨ 2

Account Number: Format: ¨ 4/2 ¨ Contact ID

Test strings: Panel normal: Panel off-normal:
Time: CMS receiver to dial: ¨ 1 ¨ 2

Account Number: Format: ¨ 4/2 ¨ Contact ID

Test strings: Panel normal: Panel off-normal:
Time: CMS receiver to dial: ¨ 1 ¨ 2

Account Number: Format: ¨ 4/2 ¨ Contact ID

Test strings: Panel normal: Panel off-normal:
Time: CMS receiver to dial: ¨ 1 ¨ 2

Account Number: Format: ¨ 4/2 ¨ Contact ID

Test strings: Panel normal: Panel off-normal:
Time: CMS receiver to dial: ¨ 1 ¨ 2

Figure 4-1: DLD Programming Worksheet (sheet 1 of 2)

QS1 Technical Reference Manual 4.25

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Job Name: Page of

Panel: Card: 14

Default Alarm Message: Account Number:

Active Message:
Restore Message:

Default Trouble Message: Account Number:

Active Message:
Restore Message:

Default Supervisory Message: Account Number:

Active Message:
Restore Message:

Figure 4-1 DLD Programming Worksheet (sheet 1 of 2)

4.26 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Job Name: Page of

Panel: Card:

004
001 ¨ NC (normally-closed) 004+ 004–
003
¨ NO (normally-open) 002
Device type: 001 JP4

002 ¨ NC (normally-closed)
¨ NO (normally-open) NC

Device type:
NO

003 ¨ NC (normally-closed)
¨ NO (normally-open)
Device type:
NC
004 ¨ NC (normally-closed)
NO
¨ NO (normally-open)
Device type:

005 ¨ NC (normally-closed) 005 JP8

¨ NO (normally-open) 006
007
Device type: 008+ 008–
008

006 ¨ NC (normally-closed)
¨ NO (normally-open)
Device type:

007 ¨ NC (normally-closed)
¨ NO (normally-open)
Device type:

008 ¨ NC (normally-closed)
¨ NO (normally-open)
Device type:

Figure 4-2: ZA8–2 Programming Worksheet

QS1 Technical Reference Manual 4.27

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Job Name: Page of

Panel:

Card:

NAC 1 device type: ¨ Audible ¨ Visible NAC 2 device type: ¨ Audible ¨ Visible
Wiring class: ¨ Class A ¨ Class B
Number of detector addresses used on loop:
Number of module addresses used on loop:

Card:

NAC 1 device type: ¨ Audible ¨ Visible NAC 2 device type: ¨ Audible ¨ Visible
Wiring class: ¨ Class A ¨ Class B
Number of detector addresses used on loop:
Number of module addresses used on loop:

Card:

NAC 1 device type: ¨ Audible ¨ Visible NAC 2 device type: ¨ Audible ¨ Visible
Wiring class: ¨ Class A ¨ Class B
Number of detector addresses used on loop:
Number of module addresses used on loop:

Card:

NAC 1 device type: ¨ Audible ¨ Visible NAC 2 device type: ¨ Audible ¨ Visible
Wiring class: ¨ Class A ¨ Class B
Number of detector addresses used on loop:
Number of module addresses used on loop:

Figure 4-3: SLIC Programming Worksheet

4.28 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Job Name: Page of

Panel: Card:

Model: S/N Device:

Sensitivity: ¨ Most ¨ More ¨ Normal ¨ Less ¨ Least

Verification: ¨ None ¨ 12 s ¨ 24 s ¨ 36 s ¨ 60 s

Pre-Alarm: ¨ None ¨ 20% ¨ 40% ¨ 60% ¨ 80%

Base type: ¨ Standard ¨ Relay ¨ Isolator

Message: 1) 2)

Model: S/N Device:

Sensitivity: ¨ Most ¨ More ¨ Normal ¨ Less ¨ Least

Verification: ¨ None ¨ 12 s ¨ 24 s ¨ 36 s ¨ 60 s

Pre-Alarm: ¨ None ¨ 20% ¨ 40% ¨ 60% ¨ 80%

Base type: ¨ Standard ¨ Relay ¨ Isolator

Message: 1) 2)

Model: S/N Device:

Sensitivity: ¨ Most ¨ More ¨ Normal ¨ Less ¨ Least

Verification: ¨ None ¨ 12 s ¨ 24 s ¨ 36 s ¨ 60 s

Pre-Alarm: ¨ None ¨ 20% ¨ 40% ¨ 60% ¨ 80%

Base type: ¨ Standard ¨ Relay ¨ Isolator

Message: 1) 2)

Model: S/N Device:

Sensitivity: ¨ Most ¨ More ¨ Normal ¨ Less ¨ Least

Verification: ¨ None ¨ 12 s ¨ 24 s ¨ 36 s ¨ 60 s

Pre-Alarm: ¨ None ¨ 20% ¨ 40% ¨ 60% ¨ 80%

Base type: ¨ Standard ¨ Relay ¨ Isolator

Message: 1) 2)

Figure 4-4: Signature Detector Programming Worksheet

QS1 Technical Reference Manual 4.29

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Job Name: Page of

Panel: Card:

Model: S/N Device: 1st) 2nd)

Device #1 Device #2

Device Type: Device Type:

Personality: Personality:

Message: 1) Message: 1)

2) 2)

Model: S/N Device: 1st) 2nd)

Device #1 Device #2

Device Type: Device Type:

Personality: Personality:

Message: 1) Message: 1)

2) 2)

Model: S/N Device: 1st) 2nd)

Device #1 Device #2

Device Type: Device Type:

Personality: Personality:

Message: 1) Message: 1)

2) 2)

Model: S/N Device: 1st) 2nd)

Device #1 Device #2

Device Type: Device Type:

Personality: Personality:

Message: 1) Message: 1)

2) 2)

Figure 4-5: Signature Module Programming Worksheet

4.30 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Job Name: Page of

Panel: Output Group:

Response: __ __ __ Type: ¨ Active ¨ Trouble

¨ Relay Device: __ __ __ __ __ ¨ On ¨ 20 bpm ¨ 120 bpm ¨ Temporal

¨ Delay Delay Type: ¨ Act and Restoration ¨ Activation ¨ Restoration Time: __ __ __ __s
¨ Dialer Account No.: __ __ __ __ Send On: ¨ Activation ¨ Restoration
Priority: ¨ Life Safety ¨ Property ¨ System Integrity
String: (CID) __ __ __ __ __ __ __ __ __ (4/2) __ __

Response: __ __ __ Type: ¨ Active ¨ Trouble

¨ Relay Device: __ __ __ __ __ ¨ On ¨ 20 bpm ¨ 120 bpm ¨ Temporal

¨ Delay Delay Type: ¨ Act and Restoration ¨ Activation ¨ Restoration Time: __ __ __ __s
¨ Dialer Account No.: __ __ __ __ Send On: ¨ Activation ¨ Restoration
Priority: ¨ Life Safety ¨ Property ¨ System Integrity
String: (CID) __ __ __ __ __ __ __ __ __ (4/2) __ __

Response: __ __ __ Type: ¨ Active ¨ Trouble

¨ Relay Device: __ __ __ __ __ ¨ On ¨ 20 bpm ¨ 120 bpm ¨ Temporal

¨ Delay Delay Type: ¨ Act and Restoration ¨ Activation ¨ Restoration Time: __ __ __ __s
¨ Dialer Account No.: __ __ __ __ Send On: ¨ Activation ¨ Restoration
Priority: ¨ Life Safety ¨ Property ¨ System Integrity
String: (CID) __ __ __ __ __ __ __ __ __ (4/2) __ __

Response: __ __ __ Type: ¨ Active ¨ Trouble

¨ Relay Device: __ __ __ __ __ ¨ On ¨ 20 bpm ¨ 120 bpm ¨ Temporal

¨ Delay Delay Type: ¨ Act and Restoration ¨ Activation ¨ Restoration Time: __ __ __ __s
¨ Dialer Account No.: __ __ __ __ Send On: ¨ Activation ¨ Restoration
Priority: ¨ Life Safety ¨ Property ¨ System Integrity
String: (CID) __ __ __ __ __ __ __ __ __ (4/2) __ __

Figure 4-6: Output Group Programming Worksheet

QS1 Technical Reference Manual 4.31

Technical Manuals Online! - http://www.tech-man.com

 Programming instructions

Job Name: Page of

Panel: Zone:

Zone Type: ¨ Alarm ¨ Supervisory ¨ Monitor

Zone Code:

Message: 1)

2)

Zone Members (32 max):

Output groups (6 max):

Figure 4-7: Zone Programming Worksheet

4.32 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Chapter 5
Standard applications

Summary
This chapter provides simplified wiring schematics for standard
applications.

Content
Notification appliance circuits • 5.2
Initiating device circuits • 5.4
Coded alarm signaling • 5.6
Remote station protective signaling system • 5.8
Auxiliary protective signaling • 5.10

QS1 Technical Reference Manual 5.1

Technical Manuals Online! - http://www.tech-man.com

 Standard applications

Notification appliance circuits

SLIC
Note: The plus and
minus symbols
NAC1 B+ indicate signal
polarity when the
NAC1 B– NAC circuit is turned
on.

NAC1 A+

NAC1 A–
UL/ULC LISTED
10 KΩ EOLR

NAC2 B+

NAC2 B–

NAC2 A+

NAC2 A–
UL/ULC LISTED
10 KΩ EOLR

Typical Class A NAC circuits

SLIC
Note: The plus and
minus symbols
NAC1 B+ indicate signal
polarity when the
NAC1 B– NAC circuit is turned
on.
NAC1 A+
NOT USED UL/ULC LISTED
NAC1 A– 10 KΩ EOLR

NAC2 B+

NAC2 B–

NAC2 A+
NOT USED UL/ULC LISTED
NAC2 A– 10 KΩ EOLR

Typical Class B NAC circuits

5.2 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Standard applications

UL/ULC LISTED
47 KΩ EOLR

10 9

SIGA–CC1 SIGA–RM1

8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1

PS6

AUX(n)
COM

SLIC
TO DATA IN TERMINALS
LOOP B+ ON NEXT DEVICE
LOOP B–

LOOP A+ TO DATA OUT TERMINALS

LOOP A– ON LAST DEVICE (CLASS A ONLY)

Note: The plus and minus symbols indicate signal polarity when the NAC circuit is turned on.
Typical NAC riser wiring

QS1 Technical Reference Manual 5.3

Technical Manuals Online! - http://www.tech-man.com

 Standard applications

Initiating device circuits

UL/ULC LISTED
EOL RELAY

PS6

24VDC+
24VDC–

JP2
ACC PWR
UL/ULC LISTED
SMK PWR 8 7 47 KΩ EOLR

SIGA–CT1

4 3 2 1

SLIC
LOOP B+ TO DATA IN TERMINALS
LOOP B– ON NEXT DEVICE

LOOP A+ TO DATA OUT TERMINALS

LOOP A– ON LAST DEVICE (CLASS A ONLY)

Typical four-wire smoke detector circuit

PS6
UL/ULC LISTED
24VDC+ 22 KΩ EOLR UL/ULC LISTED
24VDC– 15 KΩ EOLR

JP2
ACC PWR
14 13 3-2-1 12 11 10 9
SMK PWR
2–SMK SIGA–UM

8 7 6 5 4 3 2 1

SLIC
LOOP B+ TO
DATA IN TERMINALS
LOOP B– ON NEXT DEVICE

LOOP A+ TO DATA OUT TERMINALS

LOOP A– ON LAST DEVICE (CLASS A ONLY)

Typical Class B two-wire smoke detector circuit

5.4 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Standard applications

PS6
UL/ULC LISTED
24VDC+ 22 KΩ EOLR
24VDC–

JP2
ACC PWR
14 13 3-2-1 12 11 10 9
SMK PWR
2–SMK SIGA–UM

8 7 6 5 4 3 2 1

SLIC
LOOP B+ TO
DATA IN TERMINALS
LOOP B– ON NEXT DEVICE

LOOP A+ TO DATA OUT TERMINALS

LOOP A– ON LAST DEVICE (CLASS A ONLY)

Typical Class A two-wire smoke detector circuit

QS1 Technical Reference Manual 5.5

Technical Manuals Online! - http://www.tech-man.com

 Standard applications

Coded alarm signaling

1 2 3

1. FACP: Fire alarm control panel with a CPU, Notes

PS6, and standby batteries.
• Place the MFC–A and the FACP in the same
2. MFC–A Accessory Enclosure: Used for room and connect using a section of conduit no
mounting the remote fire alarm equipment. greater than 20 ft in length. Run all wiring
between cabinets through the conduit.
3. CDR–3 Bell Coder: Provides coded alarm
signals for 24 Vdc notification appliance circuits • Set SW–6 on CDR–3 to ON. Refer to the CDR–
and one of three evacuation signals (temporal, 60 3 installation sheet for programming
bpm, and 90 bpm). information.
Note: CDR–3 must have firmware version greater • Install a 10 kΩ EOLR across TB2–1 and TB2–
than 2.0. 2, and TB2–11 and TB2–12 on the CDR–3.
• Set JP2 on the PS6 for ACC PWR
• If the system uses a NAC circuit on an SLIC to
output the coded signal, program the NAC
circuit signal rate as Steady.
• If the system uses the NAC 1 circuit on an SLIC
to output the coded signal to audible notification
appliances, set JP1 and JP2 on the SLIC to
EXT.

Figure 5-1: Typical equipment layout, coded alarm signaling application

5.6 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Standard applications

PS6TB1–16

PS6TB1–18

PS6TB1–12

PS6TB1–11

PS6TB3–3 NAC RISER –

PS6TB3–1 NAC RISER +

10KΩ 10KΩ
SW1

TB1
TB2

JP1 JP2

CDR–3

Figure 5-2: Coded alarm signaling wiring (coded alarm signal only)

PS6TB1–16

PS6TB1–18

PS6TB1–12

PS6TB1–11

PS6TB3–3 NAC RISER –

PS6TB3–1 NAC RISER +

10KΩ 10KΩ
SW1

TB1
TB2

JP1 JP2

CDR–3

Figure 5-3: Coded alarm signaling wiring (coded signal followed by evacuation signal)

QS1 Technical Reference Manual 5.7

Technical Manuals Online! - http://www.tech-man.com

 Standard applications

Remote station protective signaling system

1 2 3

1. FACP: Fire alarm control panel with a CPU, Notes

PS6, ZB16–4, and standby batteries.
• Place the MFC–A and the FACP in the same
2. MFC–A Accessory Enclosure: Used for room and connect using a section of conduit no
mounting the remote fire alarm equipment. greater than 20 ft in length. Run all wiring
between cabinets through the conduit.
3. RPM Reverse Polarity Module: Provides three
independent reverse polarity signals (alarm, • Set JP2 on the PS6 for ACC PWR.
supervisory, trouble) for transmitting system status
to a remote location. • Install a 3.9 KΩ EOLR across TB1–1 and TB1–
2 on the RPM.

Figure 5-4: Typical equipment layout, Remote station protective signaling application

5.8 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Standard applications

PS6 RPM

RELAY 1 NO ALRM CITY BOX+

3.9 KΩ
RELAY 1 C JP1 CITY BOX–
RELAY 2 C
ALARM+
RELAY 2 NO SUPV
ALARM–
RELAY 3 C
TROUBLE+
RELAY 3 NO TRBL OFF-SITE
TROUBLE– MONITORING
24VDC+ +24V
SUPV+
24VDC– COM
SUPV–

Note: Plus and minus symbols indicate signal polarity when the circuit is active.

Figure 5-5: Remote station protective signaling wiring

QS1 Technical Reference Manual 5.9

Technical Manuals Online! - http://www.tech-man.com

 Standard applications

Auxiliary protective signaling

Wire as shown in Figure 5-6. Program the SIGA–CC1 as a common alarm output device. Plus and
minus symbols indicate signal polarity with the circuit turned on.

10 9 1 2

SIGA–CC1 2–CTM

8 7 6 5 4 3 2 1 2 1

LISTED 24VDC
SUPPLY Master box
24VDC+
24VDC–
TO NEXT DEVICE
SLIC
LOOP B+ TO DATA IN TERMINALS
LOOP B– ON NEXT DEVICE

LOOP A+ TO DATA OUT TERMINALS Municipal circuit

LOOP A– ON LAST DEVICE (CLASS A ONLY)

Figure 5-6: Auxiliary protective signaling cabling diagram

5.10 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Chapter 6
Maintenance instructions

Summary
This chapter provides instructions for maintaining the system.

Content
Pseudo point definitions • 6.2
Table 6-1: Main Panel pseudo points • 6.2
Table 6-2: Remote Annunciator pseudo points • 6.2
Table 6-3: Power Supply pseudo points • 6.3
Table 6-4: SLIC card pseudo points • 6.3
Table 6-5: Dialer pseudo points • 6.4
Table 6-6: General CPU pseudo points • 6.5
Maintenance tasks • 6.6

QS1 Technical Reference Manual 6.1

Technical Manuals Online! - http://www.tech-man.com

 Maintenance instructions

Pseudo point definitions

Table 6-1: Main Panel pseudo points

LCD Indication Event Type Definition

Panel xx Card Communications Trouble CPU has failed to communicate with the option
card at address xx.
Panel 01 Reset Extension Monitor/Trouble Signature loop is still resetting.
Panel 01 Service Active Trouble Trouble Service group was restored with a device still in
the active condition.
Pnl 0x Database Incompatible Trouble Changes made to the system programming on the
control panel were not updated in this unit.
Panel 01 Reboot Fault Control panel CPU restarted unexpectedly.
Panel 0x, CH1 Communications Trouble Annunciator is not communicating on RS485
channel 1.
Panel 01 Task Failure Trouble Internal processing fault.
Card xx Setup Mismatch Trouble CPU encountered problem configuring the option
card at address xx.
Dailer Setup Mismatch Trouble A problem has occurred with the CPU configuring
the dialer card.
Power Supply Setup Mismatch Trouble A problem has occurred with the CPU configuring
the POWER supply card.
Panel 01 LED/Switch display Trouble LED/Switch card is not connected.
Panel 0x, CH2 Communications Trouble Annunciator is not communicating on RS485
channel 2.
Pnl 01 Database Supervision Trouble Internal CPU memory failure
Panel 01 Code Supervision Trouble Internal CPU memory failure
Panel 01, Call For Service Trouble Internal CPU processing error
Panel 01, ROM Supervision Trouble Internal CPU memory failure
Panel 01 RS232 Port Fault Trouble
Panel 01 Unexpected Card Trouble CPU detected an option card not defined in the
database.
Panel 01 Switch Latched Trouble Button either on the main display or on an
LED/Switch card has been pressed too long.

Panel 01 Loop Database Fault Trouble Internal CPU memory failure with Signature data.

Table 6-2: Remote Annunciator pseudo points

LCD Indication Event Type Definition

Ann 0x Service Active Trouble Trouble Indicates that a device was left in an active
condition after service group has restored.
Ann 0x Database Incompatible Trouble Indicates that the data
Annunciator 0x Reboot Fault Trouble Indicates CPU has restarted due to internal
processing failure.

6.2 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Maintenance instructions

LCD Indication Event Type Definition

Ann 0x, CH1 Communications Trouble Indicates failure to communicate with the main
panel on RS485 channel 1.
Annunciator 0x Task Failure Trouble Internal software failure
Ann 0x, LED/ Switch Display Trouble Indicates that a SL30-x has been disconnected or
is connected but not defined.
Ann 0x, CH2 Communications Trouble Indicates failure to communicate with the main
panel on RS485 channel 2.
Ann 0x Database Supervision Trouble Internal memory failure
Ann 0x Code Supervision Trouble Internal memory failure
Ann 0x, Call For Service Trouble Internal software failure
Ann 0x ROM Supervision Trouble Internal memory failure
Ann 0x RS232 Port Fault Trouble
Ann 0x Program Mode Trouble Panel has entered program mode.
Ann 0x Switch Latched Trouble Indicates that a button either on the main display
or on an SL30-x has been pressed to long.
Annunciator 0x Power Fault Trouble Indicates a loss of power on either of the 24vdc
inputs to the RAI card.

Table 6-3: Power Supply pseudo points

LCD Indication Event Type Definition

Battery Charger Fault Trouble This fault will occur when the battery charger
charging voltage falls below 20.4vdc.
Battery Wiring or Battery Fault Trouble Caused by an open in the battery wiring or if the
batteries are below 20.4vdc.
Aux Power 1/2 Shorted Trouble This point occurs when Aux 1 or Aux 2 power is
shorted on the PS6
Aux Power 3 Shorted Trouble This point occurs when Aux 3
Smoke Power Shorted Trouble This point occurs when smoke power is shorted
Primary AC Power Failure Trouble Caused by loss of AC or very low AC.
Excessive Battery Current Trouble Will go active when PS6 detects over current
condition
Check System Wiring Trouble Indicates a ground fault exists on field wiring.
Power Supply Card RAM Fault Trouble Internal memory fault
Power Supply Card ROM Fault Trouble Internal memory fault
Power Supply EEPROM Fault Trouble Internal memory fault

Table 6-4: SLIC card pseudo points

LCD Indication Event Type Definition

Card 0x, Loop Wiring Problem Trouble Indicates a break on a Class A signature loop
Card 0x Map Fault Trouble Signature map is different than the one written in
memory

QS1 Technical Reference Manual 6.3

Technical Manuals Online! - http://www.tech-man.com

 Maintenance instructions

LCD Indication Event Type Definition

Card 0x, Mapping In Progress Monitor Indicates Signature devices are in the process of
being mapped.
Card 0x Unconfig. Device Trouble Indicates that a new signature device has been
detected on a loop.
Card 0x, Line Initialization Monitor Occurs after power up or a restart. Indicates
signature devices are being initialized.
Card 0x, Loop Ground Fault Trouble Indicates a ground fault on a signature module.
Card 0x, LIM Driver Fault Trouble Internal hardware failure.
Card 0x, RAM Supervision Trouble Internal memory fault
Card 0x, ROM Supervision Trouble Internal memory fault
Card 0x, EEPROM Supervision Trouble Internal memory fault

Table 6-5: Dialer pseudo points

LCD Indication Event Type Definition

Primary Phone Line:check Telco Trouble Telephone line has low or no voltage
Secondary Phone Line:check Telco Trouble Telephone line has low or no voltage
Pri. Receiver Failed to answer Trouble Dialer attempted to dial event to CMS but did not
get an answer.
Sec. Receiver Failed to answer Trouble Dialer attempted to dial event to CMS but did not
get an answer.
Dialer Account 1 Fault Trouble Indicates dialer did not get proper handshake for
event sent to the CMS for Account 1.
Dialer Account 2 Fault Trouble Indicates dialer did not get proper handshake for
event sent to the CMS for Account 2.
Dialer Account 3 Fault Trouble Indicates dialer did not get proper handshake for
event sent to the CMS for Account 3.
Dialer Account 4 Fault Trouble Indicates dialer did not get proper handshake for
event sent to the CMS for Account 4.
Dialer Account 5 Fault Trouble Indicates dialer did not get proper handshake for
event sent to the CMS for Account 5.
Dialer Account 6 Fault Trouble Indicates dialer did not get proper handshake for
event sent to the CMS for Account 6.
Dialer Account 7 Fault Trouble Indicates dialer did not get proper handshake for
event sent to the CMS for Account 7.
Dialer Account 8 Fault Trouble Indicates dialer did not get proper handshake for
event sent to the CMS for Account 8.
Dialer ROM Fault Trouble Internal memory fault
Dialer Queue Overflow Trouble Indicates that too many dialer messages are trying
to be sent.
Dialer Card, RAM Supervision Trouble Internal memory fault

6.4 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Maintenance instructions

Table 6-6: General CPU pseudo points

LCD Indication Event Type Definition

Startup Response Monitor Monitor point that goes active on system startup or
after restart.
First Alarm Alarm Occurs anytime that the system goes into alarm
for the first time.
First Supervisory Supervisory Occurs anytime that the system goes into
supervisory for the first time.
First Trouble Trouble Occurs anytime that the system goes into a
trouble for the first time.
First Monitor Monitor Occurs anytime that the system goes into a
monitor condition for the first time.
Evacuation
Drill Monitor This point will go active anytime drill is pressed.
Alarm Silence Monitor This point will go active anytime alarm silence is
pressed.
Two Stage Expiration
Reset Monitor This point goes active anytime reset is pressed.
Reset Phase 1 Monitor Active during the power down phase of reset.
Reset Phase 2 Monitor Active during the retard phase of reset.
Reset Phase 3 Monitor Active during the restoration phase of reset.
First Disable Trouble Activated the first time an item is disabled from the
front menu.
First Test Trouble Activated the first time a service group is started
from the front menus.
Two Stage Timer Started
User Trouble Trouble Triggered by custom programming.

QS1 Technical Reference Manual 6.5

Technical Manuals Online! - http://www.tech-man.com

 Maintenance instructions

Maintenance tasks

What is it you want to do This is how you do it

Change the fuse 1. Switch the circuit breaker that supplies ac power to the
control panel to the OFF position.
2. Expose the ac terminal block and pull out the fuse holder.
3. Replace the blown fuse with a new one of the same type
and size.
4. Plug the fuse holder back into the ac terminal block.
5. Switch the circuit breaker that supplies ac power to the
control panel to the ON position.

Replacing a SIGA device when WARNING: Replacing a device when mapping is disabled
mapping is disabled) leaves the area unprotected. The control panel does not
automatically reassign responses to replaced devices when
mapping is disabled.

To replace devices on a loop that operates with mapping

disabled, you must first enable mapping then accept the map.
After you replace your devices, you can disable mapping on the
loop.
Note: Replacement devices must be the same model as the
devices being replaced.
1. Press Menu.
2. Log onto the panel as a Level 4 operator.

3. Choose Enable > Loop Mapping.

4. Enter the card number of the SLIC that connects to the
device you want to replace.
Wait until mapping finishes before continuing.
5. Choose Cards > Edit.
6. Enter the card number of the SLIC that connects to the
device you want to replace.
7. Choose Accept Map.
If actual and expected data for detectors and modules are
the same, press Enter.
8. Choose Exit > Exit > Save and Sync.
9. Replace the device.

6.6 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Appendix A
System calculations

Summary
This appendix provides worksheets for calculating maximum wire lengths
for notification and Signature circuits, and for sizing standby batteries.

Content
Notification appliance circuit maximum wire length calculation • A.2
Signature loop maximum wire length calculations • A.3
Battery calculation • A.8

QS1 Technical Reference Manual A.1

Technical Manuals Online! - http://www.tech-man.com

 System calculations

Notification appliance circuit maximum wire length calculation

Use this worksheet to determine the maximum wire length of a notification appliance circuit. Fill in one
worksheet for each NAC circuit connected to the panel.

1
Maximum signal loss allowed 1.5 V

× 1000

1500
2
Wire resistance per 1000 ft/pair ÷ Ω

3
Total operating current required ÷ A

Maximum wire length ft

Notes
1. For worst case estimates, allow a 1.5-volt signal loss due to line impedance and that all appliances are clustered
at the end of the circuit.
2 2 2
2. Use 3.5 for 12 AWG and 2.5 mm wire, 5.2 for 14 AWG and 1.5 mm wire, 8.0 for 16 AWG and 1.0 mm wire, and
2
13.0 for 18 AWG and 0.75 mm wire.
3. Use the filtered 20 Vdc Average Operating Current ratings found on the installation or catalog sheet of each
device.

A.2 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 System calculations

Signature loop maximum wire length calculations

Use this worksheet to determine the maximum amount of wire you can use to construct a Signature loop.
Step 1: Calculate the total amount of wire you can used based on the cable manufacturer's capacitance
per foot rating. Total amount of wire shall not exceed the values listed in Table A-1.

500000

Cable capacitance ÷ pF/ft

Total wire ft

Table A-1: Maximum amount of wire you can use to construct a Signature loop
2
Wire type 14 AWG / 1.5 mm² 16 AWG / 1.0 mm² 18 AWG / 0.75 mm
Twisted pair, nonshielded 13157 ft 13888 ft 20000 ft
25 pF/36 pF/38 pF (4010 m) (4233 m) (6096 m)
Twisted pair, shielded 5952 ft 6098 ft 8621 ft
58 pF/82 pF/84 pF (1814 m) (1859 m) (2628 m)
Nontwisted pair, nonshielded 20000 ft 20000 ft 20000 ft
20 pF/20 pF/20 pF (6096 m) (6096 m) (6096 m)

Step 2: Use Table A-2, Table A-3, Table A-4, and Table A-5 to determine the longest allowable circuit
path based on wire size and type, and the number of detector, module, SIGA–UMs or –MABs installed on
the loop.
In the illustration below, the longest circuit path (shown in bold lines) is 1240 ft (377.95 m). The total
amount of wire comprising the loop is 1740 ft (530.35 m)

10 ft 200 ft
(3.05 m) (60.96 m)

FACP J

30 ft
(9.14 m)
200 ft 200 ft
(60.96 m) (60.96 m)

J J

100 ft 1000 ft
(30.48 m) (304.8 m)

QS1 Technical Reference Manual A.3

Technical Manuals Online! - http://www.tech-man.com

 System calculations

Table A-2: Longest allowable circuit path with 0 SIGA-UMs or SIGA-MABs configured for 2-wire
smokes
Maximum allowable wire distance using nontwisted, nonshielded wire pairs
Signature Signature
detector module 18 AWG 16 AWG 14 AWG
addresses addresses
ft m ft m ft m

1–25 0 7437 2267 11815 3601 18792 5728

26–50 0 7038 2145 11180 3408 17782 5420
51–75 0 6638 2023 10545 3214 16772 5112
76–100 0 6238 1901 9910 3021 15762 4804
101–125 0 5839 1780 9275 2827 14752 4497

0 1–25 7267 2215 11544 3519 18361 5597

1–25 1–25 6867 2093 10909 3325 17351 5289
26–50 1–25 6467 1971 10275 3132 16342 4981
51–75 1–25 6068 1849 9640 2938 15332 4673
76–100 1–25 5668 1728 9005 2745 14322 4365
101–125 1–25 5268 1606 8370 2551 13312 4057

0 26–50 6697 2041 10639 3243 16921 5157

1–25 26–50 6297 1919 10004 3049 15911 4850
26–50 26–50 5897 1798 9369 2856 14901 4542
51–75 26–50 5498 1676 8734 2662 13891 4234
76–100 26–50 5098 1554 8099 2469 12881 3926
101–125 26–50 4698 1432 7464 2275 11871 3618

0 51–75 5906 1800 9383 2860 14923 4549

1–25 51–75 5250 1600 8340 2542 13265 4043
26–50 51–75 4633 1412 7360 2243 11707 3568
51–75 51–75 4051 1235 6435 1961 10235 3120
76–100 51–75 3498 1066 5558 1694 8839 2694
101–125 51–75 2973 906 4723 1440 7512 2290
0 76–100 3931 1198 6245 1903 9932 3027
1–25 76–100 3404 1037 5407 1648 8601 2621
26–50 76–100 2899 883 4605 1404 7324 2232
51–75 76–100 2413 735 3833 1168 6096 1858
76–100 76–100 1945 593 3089 942 4913 1498
101–125 76–100 1493 455 2371 723 3771 1149

0 101–125 2631 802 4180 1274 6649 2027

1–25 101–125 2165 660 3439 1048 5470 1667
26–50 101–125 1713 522 2721 829 4328 1319
51–75 101–125 1274 388 2023 617 3218 981
76–100 101–125 847 258 1345 410 2140 652
101–125 101–125 431 131 685 209 1089 332

A.4 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 System calculations

Table A-3: Longest allowable circuit path with 1–5 SIGA-UMs or SIGA-MABs configured for 2-wire
smokes
Maximum wire distance using nontwisted, nonshielded wire pairs
Signature Signature
detector module 18 AWG 16 AWG 14 AWG
addresses addresses
ft m ft m ft m

1–25 0 6778 2066 10768 3282 17126 5220

26–50 0 6131 1869 9741 2969 15492 4722
51–75 0 5501 1677 8739 2664 13899 4236
76–100 0 4885 1489 7760 2365 12342 3762
101–125 0 4282 1305 6802 2073 10819 3298

0 1–25 5353 1632 8504 2592 13525 4122

1–25 1–25 4720 1439 7498 2286 11926 3635
26–50 1–25 4100 1250 6513 1985 10359 3157
51–75 1–25 3491 1064 5546 1691 8821 2689
76–100 1–25 2893 882 4597 1401 7311 2228
101–125 1–25 2306 703 3663 1116 5826 1776

0 26–50 3776 1151 5999 1829 9542 2908

1–25 26–50 3153 961 5009 1527 7966 2428
26–50 26–50 2539 774 4034 1230 6416 1956
51–75 26–50 1935 590 3075 937 4890 1491
76–100 26–50 1340 409 2130 649 3387 1032
101–125 26–50 754 230 1197 365 1905 581

0 51–75 2491 759 3957 1206 6293 1918

1–25 51–75 1868 569 2967 904 4720 1439
26–50 51–75 1254 382 1992 607 3168 966
51–75 51–75 648 198 1030 314 1638 499
76–100 51–75 50 15 80 24 126 39
101–125 51–75
0 76–100 1386 422 2201 671 3501 1067
1–25 76–100 760 232 1208 368 1921 586
26–50 76–100 143 44 227 69 361 110
51–75 76–100
76–100 76–100
101–125 76–100

0 101–125
1–25 101–125
26–50 101–125
51–75 101–125
76–100 101–125
101–125 101–125

QS1 Technical Reference Manual A.5

Technical Manuals Online! - http://www.tech-man.com

 System calculations

Table A-4: Longest allowable circuit path with 6–10 SIGA-UMs or SIGA-MABs configured for 2-wire
smokes
Maximum wire distance using nontwisted, nonshielded wire pairs
Signature Signature
detector module 18 AWG 16 AWG 14 AWG
addresses addresses
ft m ft m ft m

1–25 0 5045 1538 8015 2443 12748 3886

26–50 0 4494 1370 7139 2176 11355 3461
51–75 0 3950 1204 6275 1913 9981 3042
76–100 0 3414 1040 5423 1653 8625 2629
101–125 0 2884 879 4581 1396 7286 2221

0 1–25 4106 1252 6523 1988 10375 3162

1–25 1–25 3542 1080 5627 1715 8950 2728
26–50 1–25 2985 910 4742 1445 7542 2299
51–75 1–25 2435 742 3868 1179 6152 1875
76–100 1–25 1891 576 3004 916 4778 1456
101–125 1–25 1353 412 2150 655 3419 1042

0 26–50 2869 874 4557 1389 7248 2209

1–25 26–50 2296 700 3648 1112 5802 1768
26–50 26–50 1730 527 2749 838 4372 1332
51–75 26–50 1170 357 1859 567 2957 901
76–100 26–50 617 188 979 299 1558 475
101–125 26–50 68 21 108 33 172 53

0 51–75 1796 547 2853 869 4537 1383

1–25 51–75 1214 370 1929 588 3067 935
26–50 51–75 638 195 1014 309 1613 492
51–75 51–75 69 21 109 33 173 53
76–100 51–75
101–125 51–75
0 76–100 833 254 1323 403 2105 642
1–25 76–100 242 74 385 117 613 187
26–50 76–100
51–75 76–100
76–100 76–100
101–125 76–100

0 101–125
1–25 101–125
26–50 101–125
51–75 101–125
76–100 101–125
101–125 101–125

A.6 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 System calculations

Table A-5: Longest allowable circuit path with 11–15 SIGA-UMs or SIGA-MABs configured for 2-
wire smokes
Maximum wire distance using nontwisted, nonshielded wire pairs
Signature Signature
detector module 18 AWG 16 AWG 14 AWG
addresses addresses
ft m ft m ft m

1–25 0 3931 1198 6245 1903 9932 3027

26–50 0 3427 1045 5444 1659 8659 2639
51–75 0 2928 892 4651 1418 7397 2255
76–100 0 2432 741 3864 1178 6145 1873
101–125 0 1941 592 3083 940 4903 1495

0 1–25 3247 990 5158 1572 8204 2501

1–25 1–25 2722 830 4324 1318 6878 2096
26–50 1–25 2202 671 3498 1066 5563 1696
51–75 1–25 1686 514 2678 816 4259 1298
76–100 1–25 1174 358 1865 568 2966 904
101–125 1–25 666 203 1058 323 1683 513

0 26–50 2204 672 3502 1067 5570 1698

1–25 26–50 1664 507 2644 806 4205 1282
26–50 26–50 1129 344 1793 547 2852 869
51–75 26–50 598 182 950 289 1511 460
76–100 26–50 71 22 113 34 179 55
101–125 26–50

0 51–75 1263 385 2007 612 3192 973

1–25 51–75 710 216 1128 344 1794 547
26–50 51–75 161 49 256 78 407 124
51–75 51–75
76–100 51–75
101–125 51–75
0 76–100
1–25 76–100
26–50 76–100
51–75 76–100
76–100 76–100
101–125 76–100

0 101–125
1–25 101–125
26–50 101–125
51–75 101–125
76–100 101–125
101–125 101–125

QS1 Technical Reference Manual A.7

Technical Manuals Online! - http://www.tech-man.com

 System calculations

Battery calculation worksheet

Use this worksheet to determine the size of standby battery required for the panel to operate without ac power.
Obtain the current ratings for each device installed in the system from their respective installation sheets.
Example: There are 10 horns connected to NAC2. Each horn has an average operating current of 80 mA. Enter
800 mA in the Alarm box for NAC 2.
Standby (mA) Alarm (mA)

[1][5]
Base panel 249 324
[4]
Extra card

SL30

NAC 1 current load

NAC 2 current load

AUX 1 current load

AUX 2 current load

AUX 3 current load

SMK/ACC power (Form A)

[2]
Total Current Required

× hr × min

÷ 60

+ = mAh

× 1.2

mAh

÷ 1000

[3]
Battery size = Ah
Notes
[1] Base panel current includes the PS6, the CPU/Display, and a fully-loaded SLIC.
[2] If the Total Current Required value exceeds 6 A, switch part of the load to an auxiliary power source. The auxiliary power
source must be UL/ULC listed for Fire Protective Signaling Systems.
[3] If the calculated battery size exceeds 40 Ah, switch part of the load to an auxiliary power source.
[4] If a DLD is installed, enter 13 mA for Standby Current and 20 mA for Alarm Current.
If a ZR8 is installed, enter 11 mA for Standby Current and 18 mA for Alarm Current plus 18 mA for each energized relay.
If a RS485 card is installed, enter 60 mA for Standby Current and 60 mA for Alarm Current.
[5] If an SL30 is installed, enter 1 mA for Standby Current and 20 mA for Alarm Current and 0.75 mA for each energized LED.

A.8 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 System calculations

(A) Smoke/Accessory (SMK/ACC) Power current load calculation (max 250 mA)
Standby Qty × Standby Alarm Qty × Alarm
Card Qty Current (mA) Current (mA) Current (mA) Current (mA)

CDR–3 60 100

IOP3A 60 60

[1]
RPM 20 20

[3]
SIGA-UM, -MAB 2 17 17

Totals

Notes
[1] Add 0.7 mA for each output used.
[2] This represents the smoke power requirements. Only the
SIGA–UM or SIGA–MAB that signaled the alarm draws alarm
current. The remaining SIGA–UMs or SIGA–MABs do not.

QS1 Technical Reference Manual A.9

Technical Manuals Online! - http://www.tech-man.com

 System calculations

A.10 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Appendix B
Barcode library

Summary
This appendix contains a set of barcodes that you can use to add
location messages.

Content
Uppercase letters • B.2
Numbers and ordinals • B.2
Common words • B.3

QS1 Technical Reference Manual B.1

Technical Manuals Online! - http://www.tech-man.com

 Barcode library

Uppercase letters

A B C D Backspace

E F G H Delete

I J K L Enter

M N O P

Q R S T

U V W X

Y Z Space

Numbers and ordinals

1 2 3 4 Backspace

5 6 7 8 Delete

9 0 Enter

1ST 2ND 3RD 4TH

5TH 6TH 7TH 8TH

9TH 0TH

B.2 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Barcode library

Common words

ABORT

ABOVE

ALARM

APARTMENT

APT

AREA

ATRIUM

AUDITORIUM

BASEMENT

BELOW

CAFETERIA

CEILING

CLASSROOM

CLOSET

COMPUTER

CONFERENCE

CORRIDOR

DAMPER

DETECTOR

QS1 Technical Reference Manual B.3

Technical Manuals Online! - http://www.tech-man.com

 Barcode library

DOOR

DUCT

EAST

ELECTRICAL

ENTRANCE

EXIT

FAN

FAULT

FIRE

FIRE PUMP

FLAME

FLOOR

FOYER

GARAGE

GENERATOR

GYM

HALL

HEAT

HORN

JANITOR

B.4 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Barcode library

KITCHEN

LAB

LEFT

LEVEL

LIBRARY

LOBBY

LOWER

MACHINE

MECHANICAL

MENS

MEZZANINE

MONITOR

NORTH

OFFICE

PARKING

PENTHOUSE

PULL

RELAY

RESTROOM

RIGHT

QS1 Technical Reference Manual B.5

Technical Manuals Online! - http://www.tech-man.com

 Barcode library

ROOM

SECURITY

SHAFT

SMOKE

SOUTH

STAGE

STAIRWELL

STOCKROOM

STORAGE

STROBE

SUITE

SUPERVISORY

TROUBLE

UNDER

UPPER

UTILITY

WAREHOUSE

WATERFLOW

WEST

WOMENS

B.6 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Barcode library

ZONE

QS1 Technical Reference Manual B.7

Technical Manuals Online! - http://www.tech-man.com

 Barcode library

B.8 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 Appendix C
SIGA-REL programming

Summary
This appendix provides information on how to program the SIGA–REL
using the QuickStart Configuration Utility

Content
Application block diagram • C.2
Programming instructions • C.3

QS1 Technical Reference Manual C.1

Technical Manuals Online! - http://www.tech-man.com

 SIGA-REL programming

Application block diagram

FACP RACCR MFC–A

24VDC
SLIC LOOP DATA SIGA–APS LOOP DATA SIGA–REL

Minimum system requirements

• A QS1 with SLIC card and appropriately sized
standby batteries
• A SIGA–APS mounted in an RACCR enclosure
with appropriately sized standby batteries to
supply 24 Vdc to the SIGA–REL
• A SIGA–REL mounted in an MFC–A enclosure

Caution: You can not have more than 10 SIGA–

RELs on one loop.

Related documentation
Refer to the SIGA–REL Technical Reference
Manual (P/N 387348) and the latest technical
bulletins for installation and connection information.
Refer to the SIGA–APS installation sheet for
installation and connection information.
Refer to the RACCR installation sheet for
installation information.

C.2 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 SIGA-REL programming

Programming instructions
¨ Read me first WARNING: Attempting to program this application without a
complete understanding of the operation of the SIGA–REL, the
latest technical information, and the consequences of exposing
someone to fire suppression agents may cause personal injury,
event death.
WARNING: Improper application of fire suppression agents can
lead to property damage, serious injury, or loss of life. Consult
the applicable NFPA documents and the local authority having
jurisdiction (AHJ) for more information.
WARNING: Disabled and Service Group points will not prevent
activation of the release circuits.

This application requires the operation of at least two automatic

detectors to activate the fire suppression system. In order to
meet NFPA 72 requirements, you must program an And group
with at least two smoke detectors and a minimum activation
count of 2. The smoke detectors must have their Primary and
Alternate Verification properties set to None.
The SIGA–REL has six addressable circuits. To add the SIGA–
REL to the loop controller database you must add three SIGA–
RELs. The first SIGA–REL is for the Abort switch and Manual
Release switch circuits, the second for the two release circuits,
and the third for the two prerelease circuits.
Perform these instructions in order from beginning to end.
Check the check box provided as you complete each step.
As a safety precaution, disconnect releasing devices from
SIGA–REL TB4 before downloading setup data to the loop
controller.

¨ Add the Abort and Manual 1. Click Configure, then click Cabinets.
Release Switch circuits
2. Select the SLIC connected to the SIGA–REL then click
Note: Enter the information exactly as Configure.
shown to ensure that you program the
3. Click the Modules tab, then set the Quantity box to 1.
application according to manufacturer's
specifications. 4. Enter the following information:
Device Type: Monitor
Model: REL
Personality: (3) Active B
Message Specification: SIGA–REL1 A001 and ABORT SW
2nd Device Type: Pull
2nd Personality: (1) Alarm B
2nd Message Specification: SIGA–REL1 A002 and MAN
RELEASE SW
5. Click Add.

QS1 Technical Reference Manual C.3

Technical Manuals Online! - http://www.tech-man.com

 SIGA-REL programming

¨ Add the the two releasing 1. Set the Quantity box to 1.

circuits
2. Enter the following information:
Device Type: Output
Model: REL
Personality: (16) Output B
Message Specification: SIGA–REL1 A003 and RELEASE
1&2
2nd Device Type: Monitor
2nd Personality: (0) None
2nd Message Specification: SIGA–REL1 A004 and NOT
USED
3. Click Add.

¨ Add the two prerelease circuits 1. Set the Quantity box to 1.

2. Enter the following information:
Device Type: Output
Model: REL
Personality: (16) Output B
Message Specification: SIGA–REL1 A005 and
PRERELEASE 1&2
2nd Device Type: Monitor
2nd Personality: (0) None
2nd Message Specification: SIGA–REL1 A006 and NOT
USED
3. Click Add.

This is how your entries in the Modules table should look. Your addresses may be different.

Address Serial Number Device Type Model Text 1 Text 2 Personality

126 Monitor REL SIGA–REL1 A001 ABORT SW (3) Active B

127 Pull REL SIGA–REL1 A002 MAN RELEASE SW (1) Alarm B

128 Output REL SIGA–REL1 A003 RELEASE 1&2 (16) Output B

129 Monitor REL SIGA–REL1 A004 NOT USED (0) None

130 Output REL SIGA–REL1 A005 PRERELEASE 1&2 (16) Output B

132 Monitor REL SIGA–REL1 A006 NOT USED (0) None

C.4 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 SIGA-REL programming

¨ Create a response that activates 1. Click Configure > Correlations

the prerelease circuits when any
2. Click the Zones tab, then click Add Zones.
one detector in the protected
area signals an alarm 3. Click the Members tab, then click Add Device.
4. Select only the devices required to activate the SIGA–REL
prerelease circuits then click OK.
5. Click the Responses tab, click the Response Type arrow,
and then select Active.
6. Click Outputs, select the device labeled SIGA REL1 A005
PRERELEASE 1&2, and then click OK.

¨ Create a response that activates 1. Click the And Groups tab, then click Add AND Group.
the release circuits when two or
2. Set the Activation Count box for 2.
more detectors in the protected
area signal an alarm 3. Click the Members tab, then click Add Device.
Note: To comply with NFPA 72, you 4. Select only the detectors required to activate the SIGA–
must program an And Group with at REL release circuits then click OK.
least two smoke detectors and a
minimum activation count of 2. The 5. Click the Responses tab, click the Response Type arrow,
and then select Active.
smoke detectors must have their
Primary and Alternate Verification 6. Click Delays
properties set to None (verified smoke
detectors not allowed). 7. In the Delay On list, click Activation and Restoration.
8. Set the Seconds box to 10.
9. Click Outputs, select the device labeled SIGA REL1 A003
RELEASE 1&2, and then click OK.

¨ Create a response that activates 1. Click the Devices tab, then select the circuit labeled
the release circuits when someone SIGA–REL A002 MAN RELEASE SW.
presses the manual release switch
2. Click the Responses tab, click the Response Type arrow,
and then select Active.
3. Click Outputs, then:
Hold the Ctrl key down
Select the device labeled SIGA REL1 A005 Prerelease
1&2
Select the device labeled SIGA REL1 A003 Release 1&2
Release the Ctrl key then click OK.
Note: The prerelease circuit must appear before the releasing
circuit in the response list.

QS1 Technical Reference Manual C.5

Technical Manuals Online! - http://www.tech-man.com

 SIGA-REL programming

¨ Create a response that activates 1. Click the Devices tab then select the Show Pseudo Points
the prerelease circuits when check box.
someone presses the Drill switch
2. Select the circuit labeled Drill (address 007).
Note: Create this response only if
3. Click the Responses tab, click the Response Type arrow,
required. Pressing Drill will activate the
and then select Active.
prerelease circuits but pressing Drill a
second time will not restore the 4. Click Outputs, select the device labeled SIGA REL1 A005
prerelease circuits. You must press PRERELEASE 1&2, and then click OK.
Reset to silence the prerelease circuits.

¨ Retrieve the loop data from the 1. Click Configure, then click Cabinets.
SLIC
2. Select the SLIC connected to the SIGA–REL then click
Configure.
3. Set the Communications Port setting for the COM port used
to connect the service computer to the control panel.
4. Click Retrieve Signature Data
5. After the upload has finished, click OK.

¨ Reconcile the actual and 1. Click the Mapping tab, then click Model.
expected data
2. Look for a string of at least six RELs marked with red
Caution: Clicking Accept Actual will backgrounds and double-click the first REL in the string.
enter the selected device into the
3. If the serial number displayed in the Module Properties
database with its current programmed
dialog is not the same as the serial number shown on the
parameters. This will corrupt the
bar code attached to the SIGA–REL, click Close, and then
database if you have already entered
double-click the next REL in the string.
the device.
4. If the serial numbers are the same:
Click Select Expected.
In the Module Selection dialog, select the row that has the
REL with the Monitor device type and marked SIGA–REL1
A001 Abort SW, then click OK.
Click Close.
5. Select the next REL then click Select Expected.
In the Module Selection dialog, select the row that has the
REL with the Output device type and marked SIGA–REL1
A003 Release 1&2, then click OK.
Click Close.
6. Select the next REL then click Select Expected.
In the Module Selection dialog, select the row that has the
REL with the Output device type and marked SIGA–REL1
A005 Prerelease 1&2, then click OK.
Click Close.

C.6 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com

 SIGA-REL programming

¨ Send the reconciled data to the Click the Controller tab, then click Send Signature Data.
loop controller

QS1 Technical Reference Manual C.7

Technical Manuals Online! - http://www.tech-man.com

 SIGA-REL programming

C.8 QS1 Technical Reference Manual

Technical Manuals Online! - http://www.tech-man.com