Scribd
Upload
254 views

36-133 Programming Problem Error 10105

This document provides information about a programming problem and error 10105 that can occur with FH, FM, FL, and FE Volvo trucks equipped with a tachograph and new VECU. The problem is caused by an error in the VECU software. To resolve it, the MSW on the MID144 module needs to be updated using VCADS operation 36432-3 and selecting error code E1263. Disconnecting the tachograph is required before and after programming. The affected vehicle chassis numbers and part numbers are listed.

Uploaded by

Ronald Guzmán Pinedo
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
254 views

36-133 Programming Problem Error 10105

This document provides information about a programming problem and error 10105 that can occur with FH, FM, FL, and FE Volvo trucks equipped with a tachograph and new VECU. The problem is caused by an error in the VECU software. To resolve it, the MSW on the MID144 module needs to be updated using VCADS operation 36432-3 and selecting error code E1263. Disconnecting the tachograph is required before and after programming. The affected vehicle chassis numbers and part numbers are listed.

Uploaded by

Ronald Guzmán Pinedo
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Field Service Tips

Volvo Truck Corporation


Göteborg, Sweden

Date Group No. Release Page

9.10 36 133 04 1( 2 )

Programming problem, error 10105


Issued by Technical Service
10–09–16

FH, FM, FL, FE with Tachograph

Programming problem, error 10105


Concerns:
FH, FM, FL, FE with Tachograph and new VECU with HW part number 21313715 and
MSW part number 21448645 or 21475101.
Vehicles within the following chassis numbers series are concerned:
A 693437 – 695847
B 554459 –564308 (FL/FE trucks are still produced with this fault)
D 132256 – 132517
E 757313 – 759883
M 888611 – 889941
S 888697 – 889648
T 888971 – 889921
W 100248 – 100338
X 888563 – 888824
0 888627 – 889871
6 888709 – 889082
8 888571 – 889961
Vehicles where the VECU has been replaced with the new VECU can also be concerned
by this problem.

Problem:
Not possible to program ECUs or parameters. VCADS error 10105 can appear when
trying.

Reason:
Error in the VECU MSW.

Action:
For all FH/FM according to above and FL/FE built before w1023 (B 564308)
Update MID144 MSW. E-code 1263 is set for all concerned vehicles.
1. Disconnect Tachograph or remove the Tachograph fuse .
2. Run VCADS operation 36432-3 and select E1263 and program MID144
3. After programming remember to reconnect the Tachograph or replace the fuse.
For FL/FE built after w1022 (B 564308): (FST will be updated once a solution
is available.
1 Disconnect Tachograph or remove the Tachograph fuse and try to program again
2 After programming remember to reconnect the Tachograph or replace the fuse

Part number:
HW 21313715 with MSW 21448645 or 21475101.

88991318
ENG44498 English
Volvo Truck Corporation Date Group No. Release Page
Field Service Tips 9.10 36 133 04 2( 2 )

FST actions Truck within warranty Truck outside warranty


In the event of failure VTC pays warranty costs VTC does not pay warranty
costs
As a preventive measure VTC does not pay VTC does not pay

You might also like