POST MILES SHEET TOTAL

DIST COUNTY ROUTE

TOTAL PROJECT No. SHEETS

3 9"
BENT CAP BEARING #5x15" 1 DOWELS @ FESSIO
RO N
REGISTERED CIVIL ENGINEER DATE P A
12" HORIZ. TOP AND BOTTOM D
L

E
R

E
DRILL AND BOND INTO 6"

N
E

G
R E G IS T
#5 @ 12

IN E E R
DEEP HOLE, TYP.
No.
PLANS APPROVAL DATE
Exp.

The State of California or its officers or agents CIVIL

S
T
shall not be responsible for the accuracy or A
TE IA
N
completeness of scanned copies of this plan sheet. OF FOR
CALI

SEE NOTE 2
#5 @ 12 #5 @ 12
The Registered Civil Engineer for the project is responsible for the selection
and proper application of the component design and any modifications shown.
The contractor must verify
#5 @ 12 FORMED HOLE
all controlling field dimensions
CABLE before ordering or fabricating
ANCHORAGE PLATE RESTRAINER ANCHORAGE PLATE any material.
TOTAL 5

HOLE = FORMED HOLE =

CABLE UNIT CORED HOLE

CABLE YIELD
DISK SPRING INDICATOR

FORMED HOLE

1" Clr CORED HOLE CORED HOLE 1" Clr

A
6" PVC PIPE SLICED VENT =
1’-0" 2’-0" LENGTH TO CLEAR PVC PIPE
BOLSTER BOLSTER CONCRETE BOLSTER

HINGE SEAT SIDE SUPPORTED SIDE

SOFFIT SOFFIT VENT

RESTRAINER RETROFIT ON AN EXISTING STRUCTURE
" = 1’-0" VIEW V-V

EXIST CONC FACE

CONCRETE
BOLSTER

PVC PIPE
SHAPE TO FIT
5"
CONC FACE
1 PLATE
HOLE = 1"
"

PLATE
1

" HOLE FOR

" CONCRETE

ANCHORAGE ANCHORAGE DEVICE Notes

TOTAL 2
5"

HOLE PLATE SOFFIT SOFFIT VENT

1. The Formed and Cored Holes must be 6" and must be
aligned to form a straight line the entire length of the
PLATE
HOLE restrainers and be parallel to the girder. The Top of V
1 Hole must be 2" below the seat’s top main reinf.
R = 2" ´ 10x10x2" During construction, hole ends must be capped to ELEVATION
prevent debris intrusion.
1" HOLE TOTAL 5 Existing soffit vents must remain open.
EQUALLY SPACED 2. The Bearing surface must be perpendicular to girders. Where concrete bolster interferes, place
a PVC pipe extension or similar device,
3. For Cable Restrainer and Hardware details see: size to be approved by the Engineer.
1 For Location XS7-090, "Cable Restrainer Hardware Details" sheet.
of hole, see
Structure Plans. 4. Reinforcement not shown.
VIEW A-A ANCHORAGE PLATE VENT EXTENSION
" = 1’-0" 3" = 1’-0" Indicates existing structure. 1" = 1’-0"

BRIDGE NO.
BRIDGE STANDARD DETAILS STATE OF
-
The components of the Bridge Standard
NOTES TO DESIGNER
- DIVISION OF
xs7-041 July 2014 Details have been prepared under the
responsible charge of the Technical Owner,
- Place Restrainers between bearings.
CALIFORNIA POST MILE
Remove these notes at PS&E -
ENGINEERING SERVICES
FILE NO. APPROVAL DATE
a registered civil engineer in the State
of California
- DEPARTMENT OF TRANSPORTATION CABLE RESTRAINER TYPE 1 (RETROFIT)
REVISION DATES SHEET OF
Refer to: http://www.dot.ca.gov/hq/esc/techpubs/manual/bridgemanuals/bridge-standard-detail- FILE => xs7-041.dgn ORIGINAL SCALE IN INCHES UNIT: DISREGARD PRINTS BEARING
sheets/index.html FOR REDUCED PLANS EARLIER REVISION DATES
USERNAME => s136236 TIME PLOTTED => 07:27 DATE PLOTTED => 12-JUL-2016 0 1 2 3 PROJECT NUMBER & PHASE: CONTRACT NO.: 4-19-14 7-8-16