Available online at www.sciencedirect.

com
Procedia
Engineering
Procedia Procedia
Engineering 00 (2011)
Engineering 17000–000
(2011) 618 – 626
www.elsevier.com/locate/procedia

The 2nd International Symposium on Aircraft Airworthiness (ISAA 2011)

Low Emission Commercial Aircraft Engine Combustor

Development in China：From Airworthiness Requirements
to Combustor Design
FAN Renyua *, ZHANG Mana
a
AVIC Commercial Aircraft Engine CO.,LTD, 2F,Building 3, NO.555 Dongchuan Road, Shanghai,200241,China

Abstract

The development of International Civil Aviation Organization (ICAO) requirements of aircraft engine emission is
reviewed in this paper with special focus on the influence on commercial aircraft engine combustor design. As the
reason of NOX emission as the primary critical issues for combustion organization scheme during the combustor
R&D, the development status of several classical low emission combustors in the word is referred in this paper.
Based on the current technology and the future certification standards, the design perspective of the Chinese next
generation low emission commercial aircraft engine combustor is also discussed in this paper.

© 2011 Published by Elsevier Ltd. Selection and/or peer-review under responsibility of Airworthiness
Technologies Research Center NLAA, and Beijing Key Laboratory on Safety of Integrated Aircraft and
Propulsion Systems, China Open access under CC BY-NC-ND license.

Keywords: ICAO, commercial aircraft combustor design, NOx emission requirements, low emission combustor

Nomenclature
φ Equivalent ratio

CAEP Committee on Aviation Environment Protection

ICAO International Civil Aviation Organization

* Corresponding author.
E-mail address: [email protected]

1877-7058 © 2011 Published by Elsevier Ltd. Open access under CC BY-NC-ND license.
doi:10.1016/j.proeng.2011.10.078
2 FAN Renyu
FAN andZHANG
Renyu, ZHANGMan/
Man Procedia
/ ProcediaEngineering
Engineering0017(2011)
(2011)000–000
618 – 626 619

IES Independent experts

LDI Lean direct injection
LPP Lean premixed prevapourised combustor
LT Long term
LTO Landing and Take-off
MT Middle term
NOX Nitrogen oxides
RQL Rich-burn/ quench/ lean-burn combustor
TAPS Twin annular premixing swirler
TRL Technology readiness level
UEET Ultra efficient engine technology program
UHC Unburned hydrocarbons

1 INTRODUCTION OF CAEP STANDARDS

With much more concerning on the living environment and health for humanity in recent years, the
regulations and standards of emission control are launching respectively. As we know, the emission
standards of gas turbine engine are issued by the International Civil Aviation Organization (ICAO), while
the activities of environmental protection in ICAO are organized by Committee on Aviation Environment
Protection (CAEP).
For the better understanding of the restrictions for the gas turbine engine design especially of
combustor design, this paper introduces some latest emission requirements of ICAO CAEP. In the year of
2007, ICAO CAEP had held a CAEP/7-WP/11 meeting by inviting the experts of industry, university,
government and relative association in Europe and America to authorize the new regulation for the new
generation engine. During that meeting, the future commercial aircraft engine emission goal and the
future 10 years to 20 years NOX emission technical goal of commercial engine had been discussed. From
the publications released from this meeting, we can see that more stringent standards than the NOX
emission requirement of CAEP/6 in 2004 have been established. ICAO CAEP had held a CAEP/8-WP/10
meeting and reports a review by IEs of the NOX goals which set in 2007.
The time our commercial aircraft engine finishing the airworthiness certification is close to the
estimate LT technical goal reaching time, and the suggested NOX technology goal in WP/11 has far-
reaching influence to our commercial aircraft engine low emission combustor development.

2 READING OF ICAO CAEP EMISSION REQUIREMENTS

According to the provisions of ICAO CAEP, the emission pollutants of gas turbine engine are CO,
UHC, Smoke and NOX. Emission calculation is defined by LTO cycle.
The ICAO CAEP had established eight emission requirements for aircraft engines from CAEP/1 to
CAEP/8. What the emission requirements that CAEP provided are the recommended practice, not the
certification regulations. Now most of the countries choose the CAEP/2 emission requirements as the
aircraft engine certification standard.
In the 6th meeting of ICAO CAEP, the NOX emission requirement has been more stringent, the
emission requirement is what we called CAEP/6 requirement.
620 FANFAN Renyu
Renyu, and ZHANG
ZHANG Man / Procedia
Man/ Procedia Engineering
Engineering 17000–000
00 (2011) (2011) 618 – 626 3

Figure 1: The MT and LT goals of NOX emission (CAEP/7) [2]

The CAEP/7-WP/11 meeting had offered medium (MT, 10 years) and long term (LT, 20 years)
technology goals for NOX emission. The MT and LT technology goals for NOX emission separately
decrease 45% and 60% relative to CAEP/6 requirements (in Fig 1). The new technology goals of NOX
emission had put forward great challenges to commercial aircraft engine combustor low emission
combustion technology.
The CAEP/8-WP/10 meeting do not change the MT and LT technology goals which set in 2007, the
seventh meeting of ICAO CAEP. And the eighth meeting of ICAO’s CAEP recommends more stringent
Nitrogen Oxides (NOX) emission standards on large engines certified after 31 December 2013.
3 LOW EMISSION COMBUSTION PRINCIPLE AND REGULATORY MEASURES
According to the CAEP emission standard, the NOX emission requirement is more and more stringent
while smoke number and other gaseous pollutants limits are not change. The low emission combustor
critical difficulty point is NOX. In order to describe the low emission combustion regulatory measures, the
NOX formation principle will be reviewed as follows.
3.1 NOX FORMATION MECHANISM IN COMBUSTION
Nitric oxide can be produced by four different mechanisms: thermal NO, nitrous oxide mechanism,
prompt NO, and fuel NO.
Thermal nitric oxide is produced by the oxidation of atmospheric nitrogen in high-temperature regions
of the flame and in the post flame gases. The process is endothermic and it proceeds at a significant rate
only at temperatures above around 1850K. Most of the proposed reaction schemes for thermal NO utilize
the extended Zeldovich mechanism [5].
Nitrous oxide mechanism is when combustion temperature decrease and pressure increase, the reaction
temperature less than 1500K, the nitrous oxide (N2O) formed and then oxidized to NO.
4 FAN Renyu
FAN andZHANG
Renyu, ZHANGMan/
Man Procedia
/ ProcediaEngineering
Engineering0017(2011)
(2011)000–000
618 – 626 621

Prompt NO is produced by high-speed reactions at the flame front.

Fuel NO is produced by oxidation of nitrogen contained in the fuel. This portion will be ignored as a
result of the nitrogen content in the fuel is very low.
For conventional combustors, in the take-off, climb and cruise operation phase, NOX formation is
mostly from thermal nitric oxide. From the above NO formation mechanism analysis, thermal nitric oxide
plays a dominant role when equivalent ratio is approximate 1. Nowadays the pressure ratio of the in-
service dominating commercial turbofan engine is about 30~40, combustor inlet temperature is about
800~900K, outlet temperature is about 1600~1700K at take-off operation phase. The equivalent ratios of
primary zone at take-off, climb and cruise operation phase are all about 0.8. In order to reduce the NOX
production, the primary zone should achieve homogeneous combustion and avoid the partial combustion
of equivalent ratio being 1.
3.2 LOW NOX CONTROL METHOD
The main factors controlling emissions from conventional combustors may be considered in terms of:
primary-zone temperature and equivalence ratio, degree of homogeneity of the primary-zone combustion
process, residence time in the primary zone, liner-wall quenching characteristics and fuel spray
characteristics.

Fig 2: Influence of primary-zone temperature on CO and

Fig 3: Influence of equivalent ratio on CO and NOX emission [1]
NOX emissions [5]

Of all the factors influencing pollutant emissions from gas turbine combustors, the most important
by far is the temperature of the combustion zone. Figure 2 shows that too much CO is formed at
temperature 1670 K, while excessive amounts of NOX are produced at temperatures higher than
1900 K. Only in the fairly narrow band of temperatures between 1670 K and 1900 K are the levels of
CO and NOX below 25 and 15 ppmv, respectively.
Figure 3 shows that in the narrow band of equivalent ratio the emission level of both CO and NOX are
simultaneity low. There are two measures to reduce all the pollutant emissions. One is through controlling
the whole combustion zone equivalent ratio to control the combustion temperature to ensure the low
emission. The other is to control the local equivalent ratio, which is the homogeneity of the equivalent
ratio, to ensure the low emission. To intensify the mixing of fuel and air, minimize the liquid fuel
particular size after the atomization; strengthen the evaporation even using the prevaporization.
622 FANFAN Renyu
Renyu, and ZHANG
ZHANG Man / Procedia
Man/ Procedia Engineering
Engineering 17 000–000
00 (2011) (2011) 618 – 626 5

Table 1: Comparison among three combustion methods

Low emission method LPP RQL LDI
NOX emission Extremely low Very low Very low
Combustion efficiency Extremely high high high
Combustion stability Flash back No flash back Combustion unstable
Combustion unstable
Spontaneous combustion
Smoke Extremely low High Low
configuration Short length Long length Short length
Complex dome Complex dome
Development prospect Common Good Best
From fig 3, it is easily concluded that there are two methods to reach the low emission target: lean
fuel combustion and rich fuel combustion. From the two combustion methods, which LPP (Lean
Premixed Prevaporized Combustion), LDI (Lean Direct Mixing Combustion) and RQL (Rich burn -
quench - lean burn) generated.
Currently the characteristics of combustors which design according to the above low emission
control methods are comparing in table 1.
4 CLASSICAL LOW EMISSION COMBUSTORS DESIGN REVIEW
In the CAEP/7-WP/11 meeting, the MT band is supported by the combination of TALON X (P&W
P21), TAPS 2 (GE P20), and the lower portion of the R-R likely lean burn projection (R-R P18).
Perspective is established by the R-R T1000 target (787application) for 2008 certification. This product to
be certified nearly a decade before the timeframe of the MT band is only 10% above the MT band
midpoint. The MT band is narrow (+/- 2.5%) because of the quantity of near term efforts targeted for
product, giving confidence in its achievement.
The LT band is supported by TAPS 3, R-R 2020 target, TAPS CFM and UEET. This band is
considerably wider (+/-5%) due to the uncertainty caused by an additional 10 years, and the reduction in
the number of supported efforts, estimates/targets, and committed funding for this time frame.

Fig 4: RQL combustor schematic [3] Fig 5: RR LDI combustor schematic

Engine manufacturers are aware of aviation’s growing impact on the environment, continue to develop
and introduce into service cleaner and more fuel-efficient engines.
To address this environment concern, Pratt & Whitney has continued aggressive development of the
TALON family of combustors that employ advanced RQL technology (see Fig 4).
R-R develops the low emission combustor using LDI technology. The combustor is a single annular
combustor and its NOX emission decreased 50% compared with CAEP/6 emission requirements. The LDI
technology combustor (see Fig 5) will be used into Trent 1000 engine.
6 FAN
FANRenyu andZHANG
Renyu, ZHANGMan/
ManProcedia
/ Procedia Engineering
Engineering 0017 (2011)
(2011) 618 – 626
000–000 623

GE’s GEnX-1B (using TAPS 1(see Fig 6) staged lean burn combustor technology) appears very
close to achieving the MT goal according to its certification data.

Fig 6: GE TAPS combustor schematic [4]

Fig 7: Historical engine data points, recent certification s, uncertified engines and high TRL tests and demonstrations’ NOX
emission level [3]

To meet the MT and LT emission goals of CAEP/7, GE has started the development work of TAPS 2
and TAPS 3 combustor. The new technology’s major feature is having used the much more enhanced
mixing approach.
Fig 7 develops the data identifying engine types both certificated and uncertified, and has been
extended to include the high TRL demonstrators and predictions.

5 THE ROAD OF CHINESE NEXT GENERATION LOW EMISSION COMBUSTOR

5.1 EMISSION TARGETS
From CAEP/1 to CAEP/8, the NOX emission is more and more stringent and other pollutants emission
requirements are not changed in the last several meetings. Now most country’s certification is based on
CAEP/2 requirements. CAEP/6 requirements decrease 26% relative to the current certification standard
when OPR is around 30.The Buildup of Chinese commercial aircraft Engine Company triggers up the
national wide study upsurge of the low emission combustor design. According to our commercial aircraft
624 FANFAN Renyu
Renyu, and ZHANG
ZHANG Man / Procedia
Man/ Procedia Engineering
Engineering 17 000–000
00 (2011) (2011) 618 – 626 7

engine development schedule, the first demo-engine will be succeed in developing in these years, so our
aircraft engine combustor’s NOX emission target directly aims to the goals of more than 45% decreasing
compared to CAEP/6 requirements.
5.2 LOW EMISSION COMBUSTOR DESIGN DEVELOPMENT

The low emission combustor development should follow two basic principles. One is to meet the
requirements of the combustor; and the other is to follow the basic principle of low emission combustion
[1]
.
In the combustor combustion technology design, we can choose the LPP, RQL, fuel or air staging
technology to meet the CAEP emission requirements. The RQL technology has the possibility to decrease
the NOX emission further, but the lean burn technology is more potential than RQL technology for NOX
decreasing in the long run.
The combustor design is a trade-off process of stability requirements, emissions requirements,
performance requirements, reliability requirements, weight requirements, altitude re-light and starting
requirements, etc. However, the safety must be the top one what we consider the most important
requirements.

Fig 8: CFD requirement of low emission combustor Fig 9: Design loops of the product development
involved with CFD

Developments in computational fluid dynamics (CFD) techniques and supercomputers have enabled
more complicated engineering cases to be simulated. The numerical approaches to turbulent spray
reacting flow are rapidly developing in the context of the studies of aircraft combustor over the years.
However, to obtain reliable results, numerical approaches must resolve the difficulties and challenges of
modeling some complex physical processes, including turbulence, droplet clusters momentum, energy
transfer under the influence of vortices, reaction of hydrocarbon fuels and combustion oscillation. So far,
numerical studies of liquid fueled aircraft combustor are mostly carried out using Reynolds averaged
Navier-Stokes (RANS) methods in industry application[8], while large-eddy simulation (LES) approaches
to the detailed reacting mechanism study (see fig 8).
In most industrial company, CFD plays two important roles in the design process of the combustor
R&D, as shown in fig 9. Before the combustor design, CFD will accumulate the data base for the design
input, while as the validation tools after the product concept design.
To optimize the combustor design, both empirical analytical methods and advanced numerical
simulation method are required to provide insight into the combustion and emission prediction, see Fig
8 FAN
FANRenyu andZHANG
Renyu, ZHANGMan/
ManProcedia
/ Procedia Engineering
Engineering 0017 (2011)
(2011) 618 – 626
000–000 625

10.With the powerful product development tools, both the inner fluid motion and the NOx generation
mechanism could be reviewed clearly. This approach will increase the efficiency of the combustor
development.

(a)Velocity field

(b) Temperature field

(c) NOx emission field

Fig 10: Numerical simulation as useful method to predict temperature and emission distribution during combustor design.

6 CONCLUSION
Our commercial aircraft engine aims to the civil aviation market. The low emission is the inevitable
choice. The combustor is required to be designed and developed to achieve low emission performance
while maintaining safety requirements first. We should place great emphasis on the change of ICAO
CAEP emission requirements and low emission combustion technology.
626 FANFAN Renyu
Renyu, and ZHANG
ZHANG Man / Procedia
Man/ Procedia Engineering
Engineering 17000–000
00 (2011) (2011) 618 – 626 9

The following are what should pay more attention to:

a. Carry out the intellectual property and patent study ;
b. Develop the airworthiness compliance verification technology study, especially in emission test
compliance technology investigation, get ready for the future entire engine certification;
c. Carry out the CFD investigation work;
d. Carry out lots of experimental investigation work.

Acknowledgements

The author would like to thank ACAE for supporting the study of airworthiness management, and
also thank the colleagues in ACAE combustor design department for their efforts in combustor design.

References

[1] PENG Yun-hui, XU Quan-hong, ZHANG Chi, LIN Yu-zhen, LIU Gao-en. The development consideration of our
commercial aircraft low emission combustor [M]. Chinese Society of Aeronautics and Astronautics, 2007, power subject: 54
[2] Report of the independent experts on the 2006 NOX review and the establishment of medium and long term technology goals
for NOX[R], ICAO working paper CAEP/7-WP/11,2007
[3] Report of the independent experts to CAEP/8 on the second NOX review & long term technology goals[R], ICAO working
paper CAEP/8-WP/10, 2010
[4] Scott D. Stouffer and Dilip R. Ballal., et al. Development and Combustion Performance of a High-Pressure WSR and TAPS
Combustor [M]. AIAA 2005-1416
[5] Lefebvre, A.H., 1999, Gas Turbine Combustion, 2nd edition, Taylor & Francis: Philadelphia
[6]International Civil Aviation Organization, International standards and Recommended Practices, Environmental Protection,
Annex 16, to the Convention on International Civil Aviation , Volume II, Aircraft Engine Emissions, Second Edition,
1993.7,1999.11, 2005.11 revised
[7] Airworthiness Standards: Fuel Venting and Exhaust Requirements for Turbine Engine Powered Airplanes, CCAR-34,
20/03/2002.
[8] Man ZHANG “Numerical Investigation of Lean Premixed Prevaporized Combustion with Pilot Diffusion Flame in a Model
Low NOx Emission Combustor,” VKI-GRAIN2011-Lecture series, Belgium, July,2011
[9]Fenimore, C.P., 1971, Formation of Nitric Oxide in Premixed Hydrocarbon Flames, 13th Symposium(International) on
combustion, Vol. 13. Pp.373-380
[10] Mongia H C. TAPS-A 4th generation propulsion combustor technology for low emissions. AIAA 2003-2657
[11] Cheung Albert, et. Overcoming barriers to ultra emissions. ISABE 2003-1042