INTRO

PLEASE EDIT ONLY LIGHT BLUE CELLS (BOX) NOT OTHER CELLS

THANKS!
ENGR. LEANDRO B. PICZON II ([email protected])
Professional Regulation Commission Number 0088397
Gandara, Samar, Philippines
…..............................................................................................
NOTE:
Least Input Value is 0.001
Turn ON/OFF Earthquake Analysis by inputing ON or OFF
When analyzing 3 storey building just put the total height
of the building, the number of storeies and the
and column and beam on the ground floor is
computed, like wise the 2nd floor will be computed
less the height of ground floor, number of stories
shall be 1 and the lowest floor column and beam
is computed and so on...P.S. wind height value
should be the total height of the building

Download as .xls file

RELEASED 2.1 with Slab Design
RELEASED 2.2 with Slab Design minor bugs
RELEASED 2.3 with lumigwat bug REVERSED ANALYSIS
RELEASED 2.4 with Earthquake Design on Slabs
RELEASED 2.5 with Overhang Cantilever Beams
RELEASED 2.6 Minor Bugs and New Features
RELEASED 3.0 with Corner Designs
RELEASED 3.1 Minor Fixes
RELEASED 3.2 Minor Fixes
RELEASED 4.0 Shear Reinforcement Fixed
RELEASED 4.1 Earthquake Application Fixed
RELEASED 4.2 Concrete Hollow Blocks Computed
RELEASED 4.3 Loading Corrected
RELEASED 5.0 Wind Load and Reinforcement Weight added
RELEASED 5.1 Minor Fixes
RELEASED 5.2 Minor Fixes
RELEASED 5.3 Minor Fixes
RELEASED 6.0 Planted Column Introduced
RELEASED 6.1 Minor Additional Features
RELEASED 6.2 Major Fixes
RELEASED 6.3 Minor Fixes
RELEASED 6.4 Additional Features
RELEASED 6.5 Major Fixes
RELEASED 6.6 Additional Features
RELEASED 6.7 Minor Fixes
RELEASED 6.8 Minor Fixes
RELEASED 6.9 Additional Features
RELEASED 7.0 Minor Fixes
RELEASED 7.1 Additional Features
RELEASED 7.2 Minor Fixes
RELEASED 7.3 Minor Fixes

Page 1
 INTRO
RELEASED 7.4 Stairs Design Added
RELEASED 7.5 Slenderness Effect Added
RELEASED 7.6 Minor Fixes
RELEASED 7.7 Minor Fixes
RELEASED 7.8 Additional Features
RELEASED 7.9 Additional Features
RELEASED 8.0 Additional Features
RELEASED 9.0 Major Fixes
RELEASED 9.2 Minor Fixes
RELEASED 9.3 Live Load Reduction Added

Page 2
 INTRO
Dedication Public License (DPL)

By downloading the spreadsheet, you confirm your agreement in this license.

I. Freeware
First of all, the reasons why My Structural Analysis is free:

I.a. Dedication
My Structural Analysis is dedicated to the most wonderful people on earth :) Annabelle, Papa Leandro I and Mama Isabel (
My Structural Analysis is dedicated to the most wonderful place on earth :) Gandara, Samar, Philippines 6706
I.b. Binary
What do you get if you buy software? Lots of ones and zeros, nothing more. If they were distributed as art, I could understand payin
is to earn money - by fees or ads - I don't like it!
I.c. Conclusion
This means that I grant you the license to use My Structural Analysis as much as you like. But if you like it, I ask two things of you:
wonderful girl and parents you're at it ;) ) to your god - or whatever you believe - and wish us some luck.

II. Limitations

II.a. Reverse Engineering

Reverse Engineering is not allowed as with nearly any software. If anyone has doubts in the honesty of the code, I will give insight t
university under certain limitations (for example only one copy, for a limited time, and that has to be removed after the evaluation tim
II.b. Warranty
I tried my very best to make the code of My Structural Analysis as stable as possible, and I give you the warranty that I placed no c
to your system. However, adventuring sometimes involves cutting deep into the system sometimes, and I cannot guarantee that yo
same as before. For example, tensional stress hosts may stop working.

I can also give you no warranty that My Structural Analysis will calculate any structural forms, or that it will give you no false positiv
of the problem is shown with every entry, and if you have any questions remaining you can visit the support forum for more informa
II.c. Liability
Under no circumstances can you make me liable for any damage, however caused, including, but not limited to damage you might
My Structural analysis.
II.d. Use of application in whole
Free use is limited to the application in whole. Usage of parts only, for example the database or the plug-ins, is not permitted.

II.e. Corporate use

As companies are not individual persons and would have problems fullfilling the above terms, there is a license for corporate users

III. Distribution
Here are some basic rules about distributing My Structural Analysis.

III.a. Private distribution

You may give away single copies of the software as long as you don't modify this license or other files of the archive.

Page 3
 INTRO
III.b. Mirroring
If you want to mirror “My Structural Analysis”, feel free to do so as long as you don't modify the original archive. If you want to be ke
you can subscribe to the mailing list.
III.c. Publishing
You may publish My Structural Analysis in a book or magazine (or other media) by simply sending a written request for permission,
needs. I request a copy of the media in which My Structural Analysis is published as compensation.

Page 4
 INTRO

nabelle, Papa Leandro I and Mama Isabel (Deceased)

dara, Samar, Philippines 6706

re distributed as art, I could understand paying it. But if the main goal of their order

ike. But if you like it, I ask two things of you: say a prayer for me (and the most
wish us some luck.

in the honesty of the code, I will give insight to a trusted organization like a
hat has to be removed after the evaluation time has ended).

and I give you the warranty that I placed no code to cause intentional harm
m sometimes, and I cannot guarantee that your system will be running the

forms, or that it will give you no false positives. For your own verification the location
can visit the support forum for more information.

cluding, but not limited to damage you might do to your system using

abase or the plug-ins, is not permitted.

terms, there is a license for corporate users that can be found at safer-networking.ie.

se or other files of the archive.

Page 5
 INTRO

odify the original archive. If you want to be kept up to date about major updates,

mply sending a written request for permission, including a description of your specific

Page 6
 Proof
GIVEN
fc' 21 Mpa
fy 275 Mpa
As' 1500 mm2 bars in compression
As 3500 mm2 bars in tension
d 425 mm
d' 75 mm
h 500 mm
b 300 mm

SOLUTION
determine if compression bars yielded
assuming Es>es
As=As2
2
As2 1500 mm
As1 3500-1500 mm2
C= As1fy
0.85fc'ab = As1fy
a = (As1*(fy))/(0.85*fc'*b)
a = 102.71mm
Es = ((c-d')/c)*0.003
Es = 0.0011
since Es <es=0.003
compression steel has not yielded as assumed
c' = As'fs'
determine Mu
first solve for the value of c (exact analysis)
C+C' = Asfy
0.85fc'ab+As'fs' = Asfy
a=B1c
fs'=Eses
Es'=((c-d')/c)*0.003
fs'=(((c-d')/c)*0.003)*200000
fs'=600((c-d')/c)
substituting
0.85fc'(B1c)b+As'(600((c-d')/c)=Asfy
c=128.8mm
a=109.48
Mn1=c(d-(a/2)
c=0.85fc'ab
Mn1=217.07x106 N-mm
Mn2=c'(d-d')
c'=As'fs'
Mn2=131.58x106 N-mm
MN=Mn1+mn2
Mn=348.05Kn-m
Mu=øMn
Page 7
 Proof
Mu=313.78KN-m

try it on one of the beam design, override d' with 75mm

Page 8
Proof

Page 9
 Proof

Page 10
 Proof

Page 11
 Analysis

My Structural Analysis
Computing for LIVE LOAD
Weight of Person + Environment 70.00
Gravity Constant 9.81
Weight in Newtons 686.70
0.69
Number of Person/s per Square Meter 0.50
Slab Self Weight
Thickness 100.00
3.83
CHB per SQ.M. 100.00
0.98
DEAD LOAD 5.08
LIVE LOAD 0.36
Total Actual Load LL + Slab 5.42

Live Load Reduction

Width m 3.70
Length m 5.00
Tributary Area m2 18.50
3.87

Internal Span
Area
Slab 1 Short Span 1.65 (Side X) 0.00
0.13 7.67
Long Span 4.65 (Side Y) 4.40
Area
Slab 2 Short Span 4.50 (Side X) 3.70
0.94 20.93
Long Span 4.65 (Side Y) 4.40
Area
Slab 3 Short Span 3.95 (Side X) 3.70
0.77 17.78
Long Span 4.50 (Side Y) 1.50
Area
Slab 4 Short Span 1.65 (Side X) 0.00
0.17 6.52
Long Span 3.95 (Side Y) 1.50

Planted Column C(planted)=Cp mts mts mts

Top Reaction 0.0 KN Ca to C1 Ca 0.0 C1 4.4 base 0.0 mts
Top Reaction 0.0 KN Cb to C1 Cb 0.0 C1 3.7 base 0.0 mts
Top Reaction 0.0 KN Cc to C1 Cc 0.0 C1 1.5 base 0.0 mts
Top Reaction 0.0 KN Cd to C1 Cd 0.0 C1 0.0 base 0.0 mts
Input 0 if not in use
Ca
Storey height
SLAB 1 SLAB 2 Storey height
BEAM 1

Storey height
Cp Cp Storey height
4.4m 4.4m

Page 1
 Analysis

Beam 2D

Beam 2A
Beam 1D Cp Beam 1A Cp

0.001m 3.7m

Cd BEAM 4 C1 BEAM 2 Cb

0.001m 3.7m

Beam 2B
Beam 1B Cp
1.5m 1.5m

SLAB 4 BEAM 3 SLAB 3

Cc

Alternate Cross-Beam
Beam 1A Ca to C1 Ca 0.0 C1 4.4 base 0.0 mts
Beam 2A Cb to C1 Cb 0.0 C1 3.7 base 0.0 mts
Beam 1B Ca to C1 Ca 0.0 C1 3.7 base 0.0 mts
Beam 2B Cb to C1 Cb 0.0 C1 0.0 base 0.0 mts
Beam 1B Ca to C1 Ca 0.0 C1 0.0 base 0.0 mts
Beam 2B Cb to C1 Cb 0.0 C1 1.5 base 0.0 mts
Beam 1D Ca to C1 Ca 0.0 C1 4.4 base 0.0 mts
Beam 2D Cd to C1 Cd 0.0 C1 0.0 base 0.0 mts
Planted Column on Alt. Beam
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C1 3.7 base 0.0 mts
Top Reaction 0.0 KN Cb to C1 Cb 0.0 C1 4.4 base 0.0 mts
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C1 0.0 base 0.0 mts
Top Reaction 0.0 KN Cb to C1 Cb 0.0 C1 3.7 base 0.0 mts
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C1 1.5 base 0.0 mts
Top Reaction 0.0 KN Cb to C1 Cb 0.0 C1 0.0 base 0.0 mts
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C1 0.0 base 0.0 mts
Top Reaction 0.0 KN Cd to C1 Cd 0.0 C1 1.5 base 0.0 mts

Ca to C1 Bottom Reaction 0 KN Storey height

Cb to C1 Bottom Reaction 0 KN Storey height
Ca to C1 Bottom Reaction 0 KN Storey height
Cb to C1 Bottom Reaction 0 KN Storey height
Ca to C1 Bottom Reaction 0 KN Storey height
Cb to C1 Bottom Reaction 0 KN Storey height
Ca to C1 Bottom Reaction 0 KN Storey height
Cd to C1 Bottom Reaction 0 KN Storey height

NO column below? Beam 1A Shear 0 KN Moment 0 KN-m

NO column below? Beam 2A Shear 0 KN Moment 0 KN-m
NO column below? Beam 1B Shear 0 KN Moment 0 KN-m
NO column below? Beam 2B Shear 0 KN Moment 0 KN-m
NO column below? Beam 1C Shear 0 KN Moment 0 KN-m
Page 2
 Analysis
NO column below? Beam 2C Shear 0 KN Moment 0 KN-m
NO column below? Beam 1D Shear 0 KN Moment 0 KN-m
NO column below? Beam 2D Shear 0 KN Moment 0 KN-m

Beam 1 Slab 1 effect 11.43

Slab 2 effect 8.21
Total LL+Slab effect on Beam 1 19.64

Beam 2 Slab 2 effect 6.69

Slab 3 effect 7.46
Total LL+Slab effect on Beam 2 14.15

Beam 3 Slab 3 effect 2.71

Slab 4 effect 3.83
Total LL+Slab effect on Beam 3 6.54

Beam 4 Slab 4 effect 0.00

Slab 1 effect 0.00
Total LL+Slab effect on Beam 4 0.00

End of LL + Slab Computations

Beam 1 Selfweight Base 0.20 m

Height 0.40 m 11.307
Lenght 4.40 m

Beam 2 Selfweight Base 0.20 m

Height 0.40 m 7.732
Lenght 3.70 m

Beam 3 Selfweight Base 0.20 m

Height 0.40 m 9.027
Lenght 1.50 m

Beam 4 Selfweight Base 0.19 m

Height 0.38 m 8.788
Lenght 0.00 m

Computing for DESIGN MOMENT and STRESS

Beam 1 Moment (W ultL2/8) 31.51

76.26
Shear (W ultL/2) 31.51
69.33

Beam 2 Moment (W ultL2/8) 22.27

38.10
Shear (W ultL/2) 22.27
41.20

Page 3
 Analysis
2
Beam 3 Moment (W ultL /8) 16.02
4.51
Shear (W ultL/2) 16.02
12.02

Beam 4 Moment (W ultL2/8) 9.23

0.00
Shear (W ultL/2) 9.23
0.01

Transferring action to Column

Beam 1 R1=Vu/2 34.67

Beam 2 R2=Vu/2 20.60
Beam 3 R3=Vu/2 6.01
Beam 4 R4=Vu/2 0.00

Earthquake NSCP 2.2.5.2.1 (1992) Status : (ON;OFF) ON

Design Base Shear V= (ZIC/Rw)W V= 20.920
Seismic Zone Factor Z= 0.40
Importance Factor I= 1.00
Numerical Coeff Rw = 10.00
Numerical Coeff
(2/3)
C= 1.25(S)/T C= 7.28
Site Coeff S= 2.00
Fundamental Period of Vibration
Height hn= 6.40
Ct= 0.05
3/4
T= Ct(hn) T= 0.20
Applied Weight W= 71.83

Design Load for Column Pu= 176.20

Mu= 33.47

Computing Footing Reactions

Column Dimensions Base 0.20

Height 0.30
Length 6.40
Column Weight 10.55

Bottom Reaction R1+R2+R3+R4+COLUMN(WEIGHT)+Earthquake 143.66

Number of Storey 2
Design considered plus 1 storey
Overhang/Cantilever
Page 4
 Analysis
Area
Slab 5 Short Span 0.00 (Side X) 1.50
1.00 0.00
Long Span 0.00 (Side Y) 3.70
Area
Slab 6 Short Span 0.00 (Side X) 1.50
1.00 0.00
Long Span 0.00 (Side Y) 0.00
Area
Slab 5A Short Span 0.00 (Side X) 5.01
1.00 0.00
Long Span 0.00 (Side Y) 3.70
Area
Slab 6A Short Span 0.00 (Side X) 5.01
1.00 0.00
Long Span 0.00 (Side Y) 0.00

Planted Column C(planted)=Cp mts mts mts

Top Reaction 0.0 KN Ca to C2 Ca 0.0 C2 3.7 base 0.0 mts
Top Reaction 0.0 KN Jc to C2 Jc 0.0 C2 0.0 base 0.0 mts
Top Reaction 0.0 KN Jb to C2 Jb 0.0 C2 1.5 base 0.0 mts
Top Reaction 0.0 KN Ja to C2 Ja 0.0 C2 3.7 base 0.0 mts
Top Reaction 0.0 KN Cb to C2 Cb 0.0 C2 0.0 base 0.0 mts
Top Reaction 0.0 KN Along 7A to C2 0.0 C2 5.0 base 0.0 mts
Input 0 if not in use

1.5

Ca Bottom Reaction
Ca Ja
Cb Bottom Reaction
BEAM 5A

BEAM 5

3.7
BEAM1A Storey height
SLAB 5 Storey height
SLAB 5A

Storey height
5.0 3.7 Storey height
Storey height
Storey height
Beam 7A C2 BEAM 7 Jb
Storey height
Storey height
5.0
BEAM1B
BEAM 6A

BEAM 6

SLAB 6A SLAB 6 0.0

0.0

Cb Jc
1.5

Alternate Cross-Beam
Beam 1A Ca to C2 Ca 0.0 C2 3.7 base 0.0 mts
Beam 2A Jb to C2 Jb 0.0 C2 0.0 base 0.0 mts
Beam 1B Ca to C2 Ca 0.0 C2 0.0 base 0.0 mts
Beam 2B Cb to C2 Cb 0.0 C2 3.7 base 0.0 mts
Beam 1B Ca to C2 Ca 0.0 C2 0.0 base 0.0 mts
Page 5
 Analysis
Beam 2B Cb to C2 Cb 0.0 C2 5.0 base 0.0 mts
Beam 1D Ca to C2 Ca 0.0 C2 1.5 base 0.0 mts
Beam 2D Cd to C2 Cd 0.0 C2 0.0 base 0.0 mts
Planted Column on Alt. Beam
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C2 1.5 base 0.0 mts
Top Reaction 0.0 KN Cb to C1 Cb 0.0 C2 5.0 base 0.0 mts
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C2 3.7 base 0.0 mts
Top Reaction 0.0 KN Cb to C1 Cb 0.0 C2 0.0 base 0.0 mts
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C2 5.0 base 0.0 mts
Top Reaction 0.0 KN Cb to C1 Cb 0.0 C2 0.0 base 0.0 mts
Top Reaction 0.0 KN Ca to C1 Ca 0.0 C2 0.0 base 0.0 mts
Top Reaction 0.0 KN Cd to C1 Cd 0.0 C2 0.0 base 0.0 mts

Ca to C1 Bottom Reaction 0 KN Storey height

Cb to C1 Bottom Reaction 0 KN Storey height
Ca to C1 Bottom Reaction 0 KN Storey height
Cb to C1 Bottom Reaction 0 KN Storey height
Ca to C1 Bottom Reaction 0 KN Storey height
Cb to C1 Bottom Reaction #### KN Storey height
Ca to C1 Bottom Reaction 0 KN Storey height
Cd to C1 Bottom Reaction 0 KN Storey height

no column below? Beam 1A Shear 0 KN Moment 0 KN-m

NO column below? Beam 2A Shear 0 KN Moment 0 KN-m
NO column below? Beam 1B Shear 0 KN Moment 0 KN-m
NO column below? Beam 2B Shear 0 KN Moment 0 KN-m
NO column below? Beam 1C Shear 0 KN Moment 0 KN-m
NO column below? Beam 2C Shear #### KN Moment ### KN-m
NO column below? Beam 1D Shear 0 KN Moment 0 KN-m
NO column below? Beam 2D Shear 0 KN Moment 0 KN-m

Beam 5 Slab 5 effect 6.69

Total LL+Slab effect on Beam 5 6.69

Beam 6 Slab 6 effect 0.00

Total LL+Slab effect on Beam 6 0.00

Beam 7 Slab 5 effect 2.71

Slab 6 effect 0.00
Total LL+Slab effect on Beam 7 2.71

Beam 5A Slab 5 effect 6.69

Slab 5A effect 6.69
Total LL+Slab effect on Beam 5 13.38

Beam 6A Slab 6 effect 0.00

Slab 6A effect 0.00
Page 6
 Analysis
Total LL+Slab effect on Beam 6 0.00

Beam 7A Slab 5A effect 9.06

Slab 6A effect 9.06
Total LL+Slab effect on Beam 7 18.12

End of LL + Slab Computations

Beam 5 Selfweight Base 0.20 m

Height 0.30 m 1.64
Lenght 3.70 m

Beam 6 Selfweight Base 0.20 m

Height 0.30 m 8.48
Lenght 0.00 m

Beam 7 Selfweight Base 0.00 m

Height 0.00 m 0.00
Lenght 1.50 m

Beam 5A Selfweight Base 0.20 m

Height 0.40 m 16.07
Lenght 3.70 m

Beam 6A Selfweight Base 0.15 m

Height 0.38 m 8.38
Lenght 0.00 m

Beam 7A Selfweight Base 0.20 m

Height 0.40 m 16.07
Lenght 5.01 m

Computing for DESIGN MOMENT and STRESS

Beam 5 Moment (W ultL2/8) 8.41

14.39
Shear (W ultL/2) 8.41
15.56

Beam 6 Moment (W ultL2/8) 8.91

0.00
Shear (W ultL/2) 8.91
0.01

Beam 7 Moment (W ultL2/8) 2.71

16.41
Shear (W ultL/2) 2.71
12.47

Beam 5A Moment (W ultL2/8) 13.38

Page 7
 Analysis
22.90
Shear (W ultL/2) 30.25
55.96

Beam 6A Moment (W ultL2/8) 8.80

0.00
Shear (W ultL/2) 8.80
0.01

Beam 7A Moment (W ultL2/8) 18.12

56.84
Shear (W ultL/2) 34.99
87.64

Transferring action to Column

Beam 5 R5=Vu/2 7.78

Beam 6 R6=Vu/2 0.00
Beam 7 R7=(Vu/2)+R1+R2+Rpc 14.02
Beam 5A R5A=Vu/2 27.98
Beam 6A R6A=Vu/2 0.00
Beam 7A R7A=Vu/2 43.82

Earthquake NSCP 2.2.5.2.1 (1992) V= (ZIC/Rw)W

Design Base Shear V= 90.232
Seismic Zone Factor Z= 0.40
Importance Factor I= 1.00
Numerical Coeff Rw = 10.00
(2/3)
Numerical Coeff C= 1.25(S)/T
C= 7.28
Site Coeff S= 2.00
3/4
Fundamental Period of Vibration T= Ct(hn)
Height hn= 6.40
Ct= 0.05
T= 0.20
Applied Weight W= 309.81

Design Load for Column Pu= 581.52

Mu= 144.37

Computing Footing Reactions

Column Dimensions Base 0.20

Height 0.40
Length 6.40
Column Weight 223.99

Page 8
 Analysis

Bottom Reaction R7+R5A+R6A+R7A+COLUMN(WEIGHT) 619.63

Number of Storey 2.00

Overhang/Cantilever/Corner
Area
Slab 7 Short Span 0.00 (Side X) 0.00
1.00 0.00
Long Span 0.00 (Side Y) 0.00
Area
Slab 8 Short Span 0.00 (Side X) 0.00
1.00 0.00
Long Span 0.00 (Side Y) 0.00

Slab 9 Short Span 0.00 (Side X) 0.00

1.00 0.00
Long Span 0.00 (Side Y) 0.00

Slab 10 Short Span 0.00 (Side X) 0.00

1.00 0.00
Long Span 0.00 (Side Y) 0.00

Planted Column C(planted)=Cp mts mts mts

Top Reaction 0.0 KN Ca to C3 Ca 0.0 C3 0.0 base 0.0 mts
Top Reaction 0.0 KN Ja to C3 Ja 0.0 C3 0.0 base 0.0 mts
Top Reaction 0.0 KN Jd to C3 Jd 0.0 C3 0.0 base 0.0 mts
Top Reaction 0.0 KN Jc to C3 Jc 0.0 C3 0.0 base 0.0 mts
Top Reaction 0.0 KN Cb to C3 Cb 0.0 C3 0.0 base 0.0 mts
Top Reaction 0.0 KN Jb to C3 Jb 0.0 C3 0.0 base 0.0 mts
Input 0 if not in use

Ca Bottom Reaction
Ca Ja
Cb Bottom Reaction
0.0
BEAM 8
BEAM 14

Storey height
SLAB 10 0.0 SLAB 7 0.0 Storey height
Storey height
0.0 Storey height
Storey height
Storey height
Cb BEAM 15 C3 BEAM 12 Jd
Storey height
0.0 Storey height
BEAM 13

0.0
BEAM 9

0.0 SLAB 9 SLAB 8 0.0

Jb BEAM 11 Jc BEAM 10

Page 9
 Analysis
0

Beam 8 Slab 7 effect 0.00

Total LL+Slab effect on Beam 5 0.00

Beam 9 Slab 8 effect 0.00

Total LL+Slab effect on Beam 6 0.00

Beam 10 Slab 8 effect 0.00

Total LL+Slab effect on Beam 7 0.00

Beam 11 Slab 9 effect 0.00

Total LL+Slab effect on Beam 5 0.00

Beam 12 Slab 7 effect 0.00

Slab 8 effect 0.00
Total LL+Slab effect on Beam 6 0.00

Beam 13 Slab 8 effect 0.00

Slab 9 effect 0.00
Total LL+Slab effect on Beam 7 0.00

Beam 14 Slab 7 effect 0.00

Slab 10 effect 0.00
Total LL+Slab effect on Beam 6 0.00

Beam 15 Slab 9 effect 0.00

Slab 10 effect 0.00
Total LL+Slab effect on Beam 7 0.00

End of LL + Slab Computations

Beam 8 Selfweight Base 0.00 m

Height 0.00 m 10.32
Lenght 0.00 m

Beam 9 Selfweight Base 0.00 m

Height 0.00 m 0.00
Lenght 0.00 m

Beam 10 Selfweight Base 0.00 m

Height 0.00 m 0.00
Lenght 0.00 m

Beam 11 Selfweight Base 0.00 m

Height 0.00 m 0.00
Lenght 0.00 m

Page 10
 Analysis
Beam 12 Selfweight Base 0.00 m
Height 0.00 m 0.00
Lenght 0.00 m

Beam 13 Selfweight Base 0.00 m

Height 0.00 m 0.00
Lenght 0.00 m

Beam 14 Selfweight Base 0.00 m

Height 0.00 m 0.00
Lenght 0.00 m

Beam 15 Selfweight Base 0.00 m

Height 0.00 m 2.28
Lenght 0.00 m

Computing for DESIGN MOMENT and STRESS

Beam 8 Moment (W ultL2/8) 10.83

0.00
Shear (W ultL/2) 10.83
0.01

Beam 9 Moment (WL2) 0.00

0.00
Shear (WL) 0.00
0.00

Beam 10 Moment (WL2) 0.00

0.00
Shear (WL) 0.00
0.00

Beam 11 Moment (W ultL2/8) 0.00

0.00
Shear (W ultL/2) 0.00
0.00

Beam 12 Moment (WL2) 0.00

0.01
Shear (WL) 0.00
0.01

Beam 13 Moment (WL2) 0.00

0.00
Shear (WL) 0.00
0.00

Beam 14 Moment (W ultL2/8) 0.00

0.00

Page 11
 Analysis
Shear (W ultL/2) 0.00
0.00

Beam 15 Moment (W ultL2/8) 0.00

0.00
Shear (W ultL/2) 2.40
0.00

Transferring action to Column

Page 12
 Analysis
Beam 8 R8=Vu/2 0.00
Beam 9 R9=Vu 0.00
Beam 10 R10=Vu 0.00
Beam 11 R11=Vu/2 0.00
Beam 12 R12=Vu/2+R8+R9 0.00
Beam 13 R13=Vu/2+R10+R11 0.00
Beam 14 R14=Vu/2 0.00
Beam 15 R15=Vu/2 0.00

Earthquake NSCP 2.2.5.2.1 (1992) V= (ZIC/Rw)W

Design Base Shear V= 0.002
Seismic Zone Factor Z= 0.400
Importance Factor I= 1.000
Numerical Coeff Rw = 10.000
(2/3)
Numerical Coeff C= 1.25(S)/T
C= 7.281
Site Coeff S= 2.000
3/4
Fundamental Period of Vibration T= Ct(hn)
Height hn= 6.400
Ct= 0.050
T= 0.201
Applied Weight W= 0.01

Design Load for Column Pu= 0.01

Mu= 0.00

Computing Footing Reactions

Column Dimensions Base 0.00

Height 0.00
Length 6.40
Column Weight 0.00

Bottom Reaction R12+R13+R14+R15+COLUMN(WEIGHT) 0.01

Number of Storey 2.00

Wind Load
Location Samar
Heigth above ground 6.40
Analytical Procedure NSCP 2-56 exposure = B
NSCP 2-61 Ce = 0.78
NSCP 2-62 Cq = 1.40
NSCP 2-62 Cq = 1.40
NSCP 2-64 qs = 2000.00
NSCP 2-50 I= 1.00
Standard Occupancy
WLPpre = 2184

Page 13
Analysis
WLPsuc = 2184
use 1.80

Page 14
 Analysis

70.00 kgs
9.81 m/sec2
686.70 Newton (N)
0.69 KiloNewton (KN)
0.50 person/s

100.00 millimeter
3.83 KN/m2
100.00 kgs
0.98 KN/m2
5.08 KN/m2
0.36 KN/m2
5.42 KN/m2

3.70
5.00
18.50 YES
3.87 %

0.00 Meter/s
4.40 Meter/s

3.70 Meter/s
4.40 Meter/s

3.70 Meter/s
1.50 Meter/s

0.00 Meter/s
1.50 Meter/s

mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts

mts
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0

Page 15
 Analysis

height 0.0 mts

height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts

height 0.0 mts

height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
mts
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0

Page 16
 Analysis

11.43 KN/m
8.21 KN/m
19.64 KN/m

6.69 KN/m
7.46 KN/m
14.15 KN/m

2.71 KN/m
3.83 KN/m
6.54 KN/m

0.00 KN/m
0.00 KN/m
0.00 KN/m

11.307 KN/m

7.732 KN/m

9.027 KN/m

8.788 KN/m

31.51 KN/m
76.26 KN-m
31.51 KN/m
69.33 KN

22.27 KN/m
38.10 KN-m
22.27 KN/m
41.20 KN

Page 17
 Analysis
16.02 KN/m
4.51 KN-m
16.02 KN/m
12.02 KN

9.23 KN/m
0.00 KN-m
9.23 KN/m
0.01 KN

34.67 KN
20.60 KN
6.01 KN
0.00 KN

ON
20.920 KN
0.40
1.00
10.00

7.28
2.00

6.40 mts
0.05
0.20
71.83 KN

176.20 KN
33.47 KN-m

0.20 meter
0.30 meter
6.40 meter
10.55 KN

143.66 KN

2 Storeies
n considered plus 1 storey

Page 18
 Analysis

1.50 Meter/s
3.70 Meter/s

1.50 Meter/s
0.00 Meter/s

5.01 Meter/s
3.70 Meter/s

5.01 Meter/s
0.00 Meter/s

mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts

KN
KN

mts
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0

height 0.0 mts

height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
Page 19
 Analysis
height 0.0 mts
height 0.0 mts
height 0.0 mts

height 0.0 mts

height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
mts
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0

6.69 KN/m

6.69 KN/m

0.00 KN/m
KN/m
0.00 KN/m

2.71 KN/m
0.00 KN/m
2.71 KN/m

6.69 KN/m
6.69 KN/m
13.38 KN/m

0.00 KN/m
0.00 KN/m
Page 20
 Analysis
0.00 KN/m

9.06 KN/m
9.06 KN/m
18.12 KN/m

1.64 KN/m

8.48 KN/m

0.00 KN/m

16.07 KN/m

8.38 KN/m

16.07 KN/m

8.41 KN/m
14.39 KN-m
8.41 KN/m
15.56 KN

8.91 KN/m
0.00 KN-m
8.91 KN/m
0.01 KN

2.71 KN/m
16.41 KN-m
2.71 KN/m
12.47 KN

13.38 KN/m

Page 21
 Analysis
22.90 KN-m
30.25 KN/m
55.96 KN

8.80 KN/m
0.00 KN-m
8.80 KN/m
0.01 KN

18.12 KN/m
56.84 KN-m
34.99 KN/m
87.64 KN

7.78 KN
0.00 KN
14.02 KN
27.98 KN
0.00 KN
43.82 KN

90.232 KN
0.40
1.00
10.00

7.28
2.00

6.40 mts
0.05
0.20
309.81 KN

581.52 KN
144.37 KN-m

0.20 meter
0.40 meter
6.40 meter
223.99 KN

Page 22
 Analysis

619.63 KN

2.00 Storeies

0.00 Meter/s
0.00 Meter/s

0.00 Meter/s
0.00 Meter/s

0.00 Meter/s
0.00 Meter/s

0.00 Meter/s
0.00 Meter/s

mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts
height 0.0 mts

KN
KN

mts
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0
Storey height 0.0

Page 23
 Analysis

0.00 KN/m

0.00 KN/m

0.00 KN/m
KN/m
0.00 KN/m

0.00 KN/m
KN/m
0.00 KN/m

0.00 KN/m

0.00 KN/m

0.00 KN/m
0.00 KN/m
0.00 KN/m

0.00 KN/m
0.00 KN/m
0.00 KN/m

0.00 KN/m
0.00 KN/m
0.00 KN/m

0.00 KN/m
0.00 KN/m
0.00 KN/m

10.32 KN/m

0.00 KN/m

0.00 KN/m

0.00 KN/m

Page 24
 Analysis

0.00 KN/m

0.00 KN/m

0.00 KN/m

2.28 KN/m

10.83 KN/m
0.00 KN-m
10.83 KN/m
0.01 KN

0.00 KN/m
0.00 KN-m
0.00 KN/m
0.00 KN

0.00 KN/m
0.00 KN-m
0.00 KN/m
0.00 KN

0.00 KN/m
0.00 KN-m
0.00 KN/m
0.00 KN

0.00 KN/m
0.01 KN-m
0.00 KN/m
0.01 KN

0.00 KN/m
0.00 KN-m
0.00 KN/m
0.00 KN

0.00 KN/m
0.00 KN-m

Page 25
 Analysis
0.00 KN/m
0.00 KN

0.00 KN/m
0.00 KN-m
2.40 KN/m
0.00 KN

Page 26
 Analysis
0.00 KN
0.00 KN
0.00 KN
0.00 KN
0.00 KN
0.00 KN
0.00 KN
0.00 KN

0.002 KN
0.400
1.000
10.000

7.281
2.000

6.400 mts
0.050
0.201
0.01 KN

0.01 KN
0.00 KN-m

0.00 meter
0.00 meter
6.40 meter
0.00 KN

0.01 KN

2.00 Storeies

Samar
6.40 mm
B
0.78
1.40 outward
1.40 inward
2000.00 Pascal
1.00
Standard Occupancy
2184 Pascal

Page 27
 Analysis
2184 Pascal
1.80 KPA

Page 28
 SLAB
REINFORCED CONCRETE SLAB DESIGN
SLAB 1
Edge 1
C = Continuous
Ls 3700 mm D = Discontinuous
EDGE CONDITIONS
Edge 4

Edge 2
Edge 1 C
Edge 2 C
Ll 5000 mm Edge 3 C
Edge 4 C
Edge 3
SHORT SPAN LONG SPAN
LENGTH OF SLAB SPAN mm 3700 5000
2 WAY 0.74
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 20
ASSUMED SLAB THICKNESS mm 100.0
Minimum Thickness OK mm 96.7
Maximum Thickness OK mm 139.0
Smax=2t mm 200
Concrete Density kN/m3 23.5
LOADS
Selfweight kN/m2 3.83
Dead Load kN/m2 0.98
Live Load kN/m2 1.59
Actual Load kN/m2 9.56

SHORT SPAN LONG SPAN EDGE 1 EDGE 2 EDGE 3

ßs 0.007 0.024 0.009 0.032 0.009
Actual Moment kN-m 0.89 3.14 1.19 4.19 1.19
BAR SIZE mm 12 12 12 12 12
assumed spacing along mm 200 200 200 200 200
layer 1 or 2 B1 B2 T2 T1 T2
effective depth mm 74.00 62.00 62.00 74.00 62.00
Act. Steel Ratio 0.0076 0.0091 0.0091 0.0076 0.0091
Minimum Steel Ratio 0.0051 0.0051 0.0051 0.0051 0.0051
ρbal 0.0378 0.0378 0.0378 0.0378 0.0378
Max. Steel Ratio 0.0284 0.0284 0.0284 0.0284 0.0284
Adapted Steel Ratio 0.0076 0.0091 0.0091 0.0076 0.0091
Resulting Moment kN-m 9.32 9.32 9.32 9.32 9.32
Remarks SAFE SAFE SAFE SAFE SAFE
Concrete Condition DUCTILE DUCTILE DUCTILE DUCTILE DUCTILE
development length mm 136 136 136 136 136

Page 1
 SLAB

per M length

EDGE 4
0.032
4.19
12
200
T1
74.00
0.0076
0.0051
0.0378
0.0284
0.0076
9.32
SAFE
DUCTILE
136

Page 2
 STAIRS
REINFORCED CONCRETE STAIRS DESIGN
SLAB 1
Edge 1
C = Continuous
Ls 1200 mm D = Discontinuous
EDGE CONDITIONS
Edge 4

Edge 2
Edge 1 D
Edge 2 D
Ll 6000 mm Edge 3 D
Edge 4 D
Edge 3
SHORT SPAN LONG SPAN
LENGTH OF SLAB SPAN mm 1200 6000
1 WAY 0.20
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 20
ASSUMED SLAB THICKNESS mm 82.0
Minimum Thickness OK mm 80.0
Maximum Thickness OK mm 166.8
Smax=2t mm 164
Concrete Density kN/m3 23.5
LOADS
Selfweight kN/m2 3.39
Dead Load kN/m2 0.98
Live Load kN/m2 1.59
Actual Load kN/m2 10.57

SHORT SPAN LONG SPAN EDGE 1 EDGE 2 EDGE 3

ßs -0.391 0.056 0.000 0.000 0.000
Actual Moment kN-m -5.95 0.85 0.00 0.00 0.00
BAR SIZE mm 12 12 12 12 12
assumed spacing along mm 320 320 320 320 320
layer 1 or 2 B1 B2 T2 T1 T2
effective depth mm 56.00 44.00 44.00 56.00 44.00
Act. Steel Ratio 0.0063 0.0080 0.0080 0.0063 0.0080
Minimum Steel Ratio 0.0051 0.0051 0.0051 0.0051 0.0051
ρbal 0.0378 0.0378 0.0378 0.0378 0.0378
Max. Steel Ratio 0.0284 0.0284 0.0284 0.0284 0.0284
Adapted Steel Ratio 0.0063 0.0080 0.0080 0.0063 0.0080
Resulting Moment kN-m 4.41 4.41 4.41 4.41 4.41
Remarks SAFE SAFE SAFE SAFE SAFE
Concrete Condition DUCTILE DUCTILE DUCTILE DUCTILE DUCTILE
development length mm 136 136 136 136 136

Page 1
 STAIRS

per M length

EDGE 4
0.000
0.00
12
320
T1
56.00
0.0063
0.0051
0.0378
0.0284
0.0063
4.41
SAFE
DUCTILE
136

Page 2
 BEAM1
Summary Results @ Midspan BEAM 1
Bending Moment Capacity Mu = 119.46 KN-m
Moment Applied Moment Mz = 115.50 KN-m Ductile
Capacity Status PASS
Shear -92.05 KN
Cross-Section Dimensions
Height of Beam mm 400
Width of Beam mm 200
Length of Beam mm 4400
Reinforcement data
Bottom Bars 2
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 2
BAR (2) SIZE mm 16
Top Bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Weight of Main Bars kgs 4090.98
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 201.06
2
AREA OF ONE BAR (second layer) mm 201.06
2
AREA OF ONE BAR (compression) mm 201.06
2
Total Area of Compression Reinforcement Bars mm 603.19
2
Total Area of Tensile Reinforcement Bars mm 1005.31
EFFECTIVE DEPTH OF BEAM mm 326.00
Tensile STEEL RATIO 0.0154
Compression STEEL RATIO 0.0093
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0376
Steel Reinforcement Ratio at Center of Gravity 0.0242
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -78.41

Area of Shear Reinforcement mm 157.08
2/3√fc' bwd kN 199.19
(√fc'/3) bwd kN 99.59
d/4 mm 81.50
d/2 mm 163.00

Page 3
 BEAM1

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to 326.00 15.21 -170.47 107.46 131.04 81.50 81.50
326.00 733.33 112.02 -153.42 204.27 155.08 CHECK SHEAR 155.08
733.33 1233.33 188.39 -132.50 280.65 189.84 CHECK SHEAR 189.84
1233.33 1733.33 264.77 -111.58 357.02 209.72 CHECK SHEAR 209.72
1733.33 2233.33 341.15 -90.66 433.40 222.60 CHECK SHEAR 222.60
2233.33 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
d to1733.33
1733.33 to 2233.33
follow table rest at Smax

Page 4
 BEAM2
Summary Results @ Midspan BEAM 2
Bending Moment Capacity Mu = 91.50 KN-m
Moment Applied Moment Mz = 77.34 KN-m Ductile
Capacity Status PASS
Shear -63.92 KN
Cross-Section Dimensions
Height of Beam mm 400
Width of Beam mm 200
Length of Beam mm 3000
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Weight if Bars kgs 2091.98
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 201.06
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 201.06
2
Total Area of Compression Reinforcement Bars mm 603.19
2
Total Area of Tensile Reinforcement Bars mm 603.19
EFFECTIVE DEPTH OF BEAM mm 326.00
Tensile STEEL RATIO 0.0093
Compression STEEL RATIO 0.0093
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0376
Steel Reinforcement Ratio at Center of Gravity 0.0242
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -50.03

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 199.19
(√fc'/3) bwd kN 99.59
d/4 mm 81.50
d/2 mm 163.00

Page 1
 BEAM2

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to 326.00 15.21 -113.95 74.07 190.12 163.00 163.00
326.00 500.00 76.38 -106.53 135.23 159.71 81.50 81.50
500.00 1000.00 152.75 -85.23 211.61 204.14 CHECK SHEAR 204.14
1000.00 1500.00 229.13 -63.92 287.98 225.00 CHECK SHEAR 225.00
1500.00 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
d to1500
#VALUE!
follow table rest at Smax

Page 2
 BEAM3
Summary Results @ Midspan BEAM 3
Bending Moment Capacity Mu = 91.50 KN-m
Moment Applied Moment Mz = 43.74 KN-m Ductile
Capacity Status PASS
Shear -34.74 KN
Cross-Section Dimensions
Height of Beam mm 400
Width of Beam mm 200
Length of Beam mm 1500
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Weight if Bars kgs 1045.99
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 201.06
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 201.06
2
Total Area of Compression Reinforcement Bars mm 603.19
2
Total Area of Tensile Reinforcement Bars mm 603.19
EFFECTIVE DEPTH OF BEAM mm 326.00
Tensile STEEL RATIO 0.0093
Compression STEEL RATIO 0.0093
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0376
Steel Reinforcement Ratio at Center of Gravity 0.0242
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -19.64

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 199.19
(√fc'/3) bwd kN 99.59
d/4 mm 81.50
d/2 mm 163.00

Page 1
 BEAM3

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to 326.00 15.21 -54.38 38.32 367.49 163.00 163.00
326.00 250.00 38.19 -57.90 61.29 176.19 163.00 163.00
250.00 750.00 114.56 -34.74 137.67 235.33 81.50 81.50
750.00 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax

Page 2
 BEAM4
Summary Results @ Midspan BEAM 4
Bending Moment Capacity Mu = 84.55 KN-m
Moment Applied Moment Mz = 39.24 KN-m Ductile
Capacity Status PASS
Shear -20.93 KN
Cross-Section Dimensions
Height of Beam mm 375
Width of Beam mm 190
Length of Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Weight if Bars kgs 0.70
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 201.06
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 201.06
2
Total Area of Compression Reinforcement Bars mm 603.19
2
Total Area of Tensile Reinforcement Bars mm 603.19
EFFECTIVE DEPTH OF BEAM mm 309.00
Tensile STEEL RATIO 0.0103
Compression STEEL RATIO 0.0103
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0386
Steel Reinforcement Ratio at Center of Gravity 0.0261
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN 12912.42

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 179.36
(√fc'/3) bwd kN 89.68
d/4 mm 77.25
d/2 mm 154.50

Page 1
 BEAM4

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to 309.00 13.01 12891.49 15178.07 0.88 CHECK SHEAR 0.88
309.00 0.17 0.02 -34.88 15191.06 0.00 CHECK SHEAR 0.00
0.17 500.17 72.58 20892.87 15118.50 1.43 CHECK SHEAR 1.43
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax

Page 2
 BEAM5
Summary Results @ Midspan BEAM 5
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 164.53 KN-m Ductile
Capacity Status FAIL
Shear -107.60 KN
Cross-Section Dimensions
Height of Beam mm 300
Width of Beam mm 200
Length of Beam mm 3700
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 0.00
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 0.00
2
Total Area of Compression Reinforcement Bars mm 0.00
2
Total Area of Tensile Reinforcement Bars mm 0.00
EFFECTIVE DEPTH OF BEAM mm 250.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity 0.0163
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -93.06

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 152.75
(√fc'/3) bwd kN 76.38
d/4 mm 62.50
d/2 mm 125.00

Page 1
 BEAM5

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to 250.00 11.67 -200.65 121.14 89.14 62.50 62.50
250.00 616.67 94.20 -179.33 203.68 130.79 CHECK SHEAR 130.79
616.67 1116.67 170.57 -150.25 280.05 172.24 CHECK SHEAR 172.24
1116.67 1616.67 246.95 -121.17 356.43 195.93 CHECK SHEAR 195.93
1616.67 2116.67 323.33 -92.09 432.80 211.26 CHECK SHEAR 211.26
2116.67 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
d to1616.67
1616.67 to 2116.67
follow table rest at Smax

Page 2
 BEAM5A
Summary Results@ Midspan BEAM 5A
Bending Moment Capacity Mu = 179.24 KN-m
Moment Applied Moment Mz = 166.55 KN-m Ductile
Capacity Status PASS
Shear -104.50 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 400
Width of Cantilever Beam mm 200
Length of Cantilever Beam mm 3700
Reinforcement data
Bottom Bars 2
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 2
BAR (2) SIZE mm 20
Top Bars
Number of Reinforce Bars (1) 5
BAR (1) SIZE mm 17.6
Weight if Bars kgs 5235.47
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 201.06
2
AREA OF ONE BAR (second layer) mm 314.16
2
AREA OF ONE BAR (compression) mm 243.29
2
Total Area of Compression Reinforcement Bars mm 1216.43
2
Total Area of Tensile Reinforcement Bars mm 1231.51
EFFECTIVE DEPTH OF BEAM mm 334.00
Tensile STEEL RATIO 0.0184
Compression STEEL RATIO 0.0182
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0466
Steel Reinforcement Ratio at Center of Gravity 0.0331
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -85.63

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 204.08
(√fc'/3) bwd kN 102.04
d/4 mm 83.50
d/2 mm 167.00

Page 1
 BEAM5A

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to 334.00 15.59 -190.13 116.33 124.02 83.50 83.50
334.00 616.67 94.20 -174.17 194.94 136.65 83.50 83.50
616.67 1116.67 170.57 -145.92 271.32 177.79 CHECK SHEAR 177.79
1116.67 1616.67 246.95 -117.68 347.70 200.85 CHECK SHEAR 200.85
1616.67 2116.67 323.33 -89.44 424.07 215.61 CHECK SHEAR 215.61
2116.67 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
d to1616.67
1616.67 to 2116.67
follow table rest at Smax

Page 2
 BEAM6
Summary Results @ Midspan BEAM 6
Bending Moment Capacity Mu = 62.53 KN-m
Moment Applied Moment Mz = 20.00 KN-m Ductile
Capacity Status PASS
Shear -92.04 KN
Cross-Section Dimensions
Height of Beam mm 300
Width of Beam mm 200
Length of Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 4
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 2
BAR (1) SIZE mm 16
Weight if Bars kgs 0.70
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 201.06
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 201.06
2
Total Area of Compression Reinforcement Bars mm 402.12
2
Total Area of Tensile Reinforcement Bars mm 804.25
EFFECTIVE DEPTH OF BEAM mm 234.00
Tensile STEEL RATIO 0.0172
Compression STEEL RATIO 0.0086
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0370
Steel Reinforcement Ratio at Center of Gravity 0.0295
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN 42982.55

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 142.98
(√fc'/3) bwd kN 71.49
d/4 mm 58.50
d/2 mm 117.00

Page 1
 BEAM6

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to 234.00 10.92 42890.51 50556.78 0.20 CHECK SHEAR 0.20
234.00 0.17 0.03 -153.40 50567.68 0.00 CHECK SHEAR 0.00
0.17 500.17 76.40 91886.32 50491.30 0.43 CHECK SHEAR 0.43
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax

Page 2
 BEAM6A
Summary Results @ Midspan BEAM 6A
Bending Moment Capacity Mu = 83.17 KN-m
Moment Applied Moment Mz = 150.14 KN-m Ductile
Capacity Status FAIL
Shear -92.04 KN
Cross-Section Dimensions
Height of Beam mm 375
Width of Beam mm 150
Length of Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Weight if Bars kgs 0.70
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 201.06
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 201.06
2
Total Area of Compression Reinforcement Bars mm 603.19
2
Total Area of Tensile Reinforcement Bars mm 603.19
EFFECTIVE DEPTH OF BEAM mm 309.00
Tensile STEEL RATIO 0.0130
Compression STEEL RATIO 0.0130
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0414
Steel Reinforcement Ratio at Center of Gravity 0.0288
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN 56788.51

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 141.60
(√fc'/3) bwd kN 70.80
d/4 mm 77.25
d/2 mm 154.50

Page 1
 BEAM6A

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to 309.00 8.11 56696.47 66801.90 0.20 CHECK SHEAR 0.20
309.00 0.17 0.02 -153.40 66809.99 0.00 CHECK SHEAR 0.00
0.17 500.17 57.30 91886.32 66752.71 0.32 CHECK SHEAR 0.32
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax

Page 2
 BEAM7
Summary Results Cantilever Beam BEAM 7
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 166.55 KN-m Ductile
Capacity Status FAIL
Shear -104.50 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1500
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 0.00
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 0.00
2
Total Area of Compression Reinforcement Bars mm 0.00
2
Total Area of Tensile Reinforcement Bars mm 0.00
EFFECTIVE DEPTH OF BEAM mm -50.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0815
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -111.47

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 0.00
(√fc'/3) bwd kN 0.00
d/4 mm -12.50
d/2 mm -25.00

Page 1
 BEAM7

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to -50.00 0.00 -215.97 131.14 -16.47 CHECK SHEAR CHECK SHEAR
-50.00 250.00 0.00 -174.17 131.14 82.35 CHECK SHEAR 82.35
250.00 750.00 0.00 -104.50 131.14 247.05 CHECK SHEAR 247.05
750.00 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax

Page 2
 BEAM7A
Summary Results @ Midspan BEAM 7A
Bending Moment Capacity Mu = 179.24 KN-m
Moment Applied Moment Mz = 166.55 KN-m Ductile
Capacity Status PASS
Shear -104.50 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 400
Width of Cantilever Beam mm 200
Length of Cantilever Beam mm 5010
Reinforcement data
Bottom Bars 2
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 2
BAR (2) SIZE mm 20
Top Bars
Number of Reinforce Bars (1) 5
BAR (1) SIZE mm 17.6
Weight if Bars kgs 7089.11
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 201.06
2
AREA OF ONE BAR (second layer) mm 314.16
2
AREA OF ONE BAR (compression) mm 243.29
2
Total Area of Compression Reinforcement Bars mm 1216.43
2
Total Area of Tensile Reinforcement Bars mm 1231.51
EFFECTIVE DEPTH OF BEAM mm 334.00
Tensile STEEL RATIO 0.0184
Compression STEEL RATIO 0.0182
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0466
Steel Reinforcement Ratio at Center of Gravity 0.0331
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -90.57

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 204.08
(√fc'/3) bwd kN 102.04
d/4 mm 83.50
d/2 mm 167.00

Page 1
 BEAM7A

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to 334.00 15.59 -195.07 122.14 118.13 83.50 83.50
334.00 835.00 127.55 -174.17 234.10 154.08 CHECK SHEAR 154.08
835.00 1335.00 203.92 -153.31 310.47 185.74 CHECK SHEAR 185.74
1335.00 1835.00 280.30 -132.45 386.85 204.90 CHECK SHEAR 204.90
1835.00 2335.00 356.68 -111.59 463.23 217.74 CHECK SHEAR 217.74
2335.00 2835.00 433.05 -90.73 539.60 226.95 CHECK SHEAR 226.95
Support

L/2

1@50mm
0 to d
d to1835
1835 to 2335
follow table rest at Smax

Page 2
 BEAM8
Summary Results @ Midspan BEAM 8
Bending Moment Capacity Mu = -716987.87 KN-m
Moment Applied Moment Mz = 22.18 KN-m Ductile
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 3
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 5
BAR (1) SIZE mm 17.6
Weight if Bars kgs 1.05
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 201.06
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 243.29
2
Total Area of Compression Reinforcement Bars mm 1216.43
2
Total Area of Tensile Reinforcement Bars mm 603.19
EFFECTIVE DEPTH OF BEAM mm -66.00
Tensile STEEL RATIO -9139.3385
Compression STEEL RATIO -18430.9993
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO -18430.9709
Steel Reinforcement Ratio at Center of Gravity -18431.0746
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -1897.78

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 0.00
(√fc'/3) bwd kN 0.00
d/4 mm -16.50
d/2 mm -33.00

Page 1
 BEAM8

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to -66.00 0.00 -1912.05 2232.69 -1.28 CHECK SHEAR CHECK SHEAR
-66.00 0.17 0.00 -23.78 2232.69 0.00 CHECK SHEAR 0.00
0.17 500.17 0.00 14245.48 2232.69 9.68 CHECK SHEAR 9.68
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax

Page 2
 BEAM9
Summary Results @ Midspan BEAM 9
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 22.18 KN-m Ductile
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 0.00
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 0.00
2
Total Area of Compression Reinforcement Bars mm 0.00
2
Total Area of Tensile Reinforcement Bars mm 0.00
EFFECTIVE DEPTH OF BEAM mm -50.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0815
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -1441.20

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 0.00
(√fc'/3) bwd kN 0.00
d/4 mm -12.50
d/2 mm -25.00

Page 1
 BEAM9

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to -50.00 0.00 -1455.46 1695.52 -1.27 CHECK SHEAR CHECK SHEAR
-50.00 0.17 0.00 -23.78 1695.52 0.00 CHECK SHEAR 0.00
0.17 500.17 0.00 14245.48 1695.52 12.74 CHECK SHEAR 12.74
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax

Page 2
 BEAM10
Summary Results @ Midspan BEAM 10
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 22.18 KN-m Ductile
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 0.00
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 0.00
2
Total Area of Compression Reinforcement Bars mm 0.00
2
Total Area of Tensile Reinforcement Bars mm 0.00
EFFECTIVE DEPTH OF BEAM mm -50.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0815
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -1441.20

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 0.00
(√fc'/3) bwd kN 0.00
d/4 mm -12.50
d/2 mm -25.00

Page 1
 BEAM10

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to -50.00 0.00 -1455.46 1695.52 -1.27 CHECK SHEAR CHECK SHEAR
-50.00 0.17 0.00 -23.78 1695.52 0.00 CHECK SHEAR 0.00
0.17 500.17 0.00 14245.48 1695.52 12.74 CHECK SHEAR 12.74
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax

Page 2
 BEAM11
Summary Results @ Midspan BEAM 11
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 22.18 KN-m Ductile
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 0.00
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 0.00
2
Total Area of Compression Reinforcement Bars mm 0.00
2
Total Area of Tensile Reinforcement Bars mm 0.00
EFFECTIVE DEPTH OF BEAM mm -50.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
1 MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0815
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -1441.20

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 0.00
(√fc'/3) bwd kN 0.00
d/4 mm -12.50
d/2 mm -25.00

Page 1
 BEAM11

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to -50.00 0.00 -1455.46 1695.52 -1.27 CHECK SHEAR CHECK SHEAR
-50.00 0.17 0.00 -23.78 1695.52 0.00 CHECK SHEAR 0.00
0.17 500.17 0.00 14245.48 1695.52 12.74 CHECK SHEAR 12.74
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax

Page 2
 BEAM12
Summary Results Cantilever Beam BEAM 12
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 22.18 KN-m Ductile
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 0.00
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 0.00
2
Total Area of Compression Reinforcement Bars mm 0.00
2
Total Area of Tensile Reinforcement Bars mm 0.00
EFFECTIVE DEPTH OF BEAM mm -50.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
1 MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0815
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -1441.20

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 0.00
(√fc'/3) bwd kN 0.00
d/4 mm -12.50
d/2 mm -25.00

Page 1
 BEAM12

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to -50.00 0.00 -1455.46 1695.52 -1.27 CHECK SHEAR CHECK SHEAR
-50.00 0.17 0.00 -23.78 1695.52 0.00 CHECK SHEAR 0.00
0.17 500.17 0.00 14245.48 1695.52 12.74 CHECK SHEAR 12.74
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax

Page 2
 BEAM13
Summary Results Cantilever Beam BEAM 13
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 22.18 KN-m Ductile
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 0.00
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 0.00
2
Total Area of Compression Reinforcement Bars mm 0.00
2
Total Area of Tensile Reinforcement Bars mm 0.00
EFFECTIVE DEPTH OF BEAM mm -50.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0815
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -1441.20

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 0.00
(√fc'/3) bwd kN 0.00
d/4 mm -12.50
d/2 mm -25.00

Page 1
 BEAM13

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to -50.00 0.00 -1455.46 1695.52 -1.27 CHECK SHEAR CHECK SHEAR
-50.00 0.17 0.00 -23.78 1695.52 0.00 CHECK SHEAR 0.00
0.17 500.17 0.00 14245.48 1695.52 12.74 CHECK SHEAR 12.74
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax

Page 2
 BEAM14
Summary Results @ Midspan BEAM 14
Bending Moment Capacity Mu = 0.00 KN-m
Moment Applied Moment Mz = 22.18 KN-m Ductile
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.00
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 0.00
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 0.00
2
Total Area of Compression Reinforcement Bars mm 0.00
2
Total Area of Tensile Reinforcement Bars mm 0.00
EFFECTIVE DEPTH OF BEAM mm -50.00
Tensile STEEL RATIO 0.0000
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0815
Compression Steel Yields
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -1441.20

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 0.00
(√fc'/3) bwd kN 0.00
d/4 mm -12.50
d/2 mm -25.00

Page 1
 BEAM14

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to -50.00 0.00 -1455.46 1695.52 -1.27 CHECK SHEAR CHECK SHEAR
-50.00 0.17 0.00 -23.78 1695.52 0.00 CHECK SHEAR 0.00
0.17 500.17 0.00 14245.48 1695.52 12.74 CHECK SHEAR 12.74
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax

Page 2
 BEAM15
Summary Results @ Midspan BEAM 15
Bending Moment Capacity Mu = -308295.37 KN-m
Moment Applied Moment Mz = 22.18 KN-m Ductile
Capacity Status FAIL
Shear -14.27 KN
Cross-Section Dimensions
Height of Cantilever Beam mm 0.001
Width of Cantilever Beam mm 0.001
Length of Cantilever Beam mm 1
Reinforcement data
Bottom Bars 1
First layer bars
Number of Reinforce Bars (1) 2
BAR (1) SIZE mm 16
Second layer bars
Number of Reinforce Bars (2) 0.001
BAR (2) SIZE mm 0.001
Top Bars
Number of Reinforce Bars (1) 0.001
BAR (1) SIZE mm 0.001
Weight if Bars kgs 0.23
Stirrup Size mm 10
Strength Reduction Factor 0.9
Steel Yield Strength MPA 275
Concrete Compressive Strength MPA 21
Concrete Cover mm 40
2
AREA OF ONE BAR (first layer) mm 201.06
2
AREA OF ONE BAR (second layer) mm 0
2
AREA OF ONE BAR (compression) mm 0.00
2
Total Area of Compression Reinforcement Bars mm 0.00
2
Total Area of Tensile Reinforcement Bars mm 402.12
EFFECTIVE DEPTH OF BEAM mm -66.00
Tensile STEEL RATIO -6092.8923
Compression STEEL RATIO 0.0000
MINIMUM STEEL RATIO 0.0051
Factor b 1 0.850
Reinforcement ratio producing balanced strain condition 0.0378
MAXIMUM STEEL Reinforcement RATIO 0.0284
MAXIMUM STEEL Double Reinforcement RATIO 0.0284
Steel Reinforcement Ratio at Center of Gravity -0.0617
Compression Steel does not Yield
Ductility Test Beam is: Ductile
Shear Reinforcement

Vu @ a distance of "d" from face of support kN -1897.78

Area of Shear Reinfrocement mm 157.08
2/3√fc' bwd kN 0.00
(√fc'/3) bwd kN 0.00
d/4 mm -16.50
d/2 mm -33.00

Page 1
 BEAM15

Distance from Vc Vu Vs S Smax Use

face of support (mm) (KN) (KN) (KN) (mm) (mm) (mm)
50 to -66.00 0.00 -1912.05 2232.69 -1.28 CHECK SHEAR CHECK SHEAR
-66.00 0.17 0.00 -23.78 2232.69 0.00 CHECK SHEAR 0.00
0.17 500.17 0.00 14245.48 2232.69 9.68 CHECK SHEAR 9.68
500.17 rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
rest at rest at #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE!
Support

L/2

1@50mm
0 to d
#VALUE!
#VALUE!
follow table rest at Smax

Page 2
 COLUMN1
DESIGN OF BOTTOM INNER COLUMNS

Summary Results
Applied Moment Mu max = 39.24 KN-m RESULTS
Applied Axial Load Pumax = 354.27 KN Ductile
Nominal Load 506.09 KN SLENDER
Pass 638.19 KN
Additional Reaction Mu= 0.00 KN-m
Pu= 0.00 KN
Cross-Section Dimensions
Height of Beam critical axis H= 300 mm X
Base of Beam B= 200 mm
Other Datas
Concrete Cover 70 mm
Bar Type Fc' = 21 Mpa
Fy = 275 Mpa
e= 110.76 mm
Bars Bar Pcs stirrups = 10 mm
16 4 corner mm
12 4 in between
As = 515.2224 mm2
As2 = 226.1952 mm2
x1 = 80 mm
x2 = 160 mm
x3 = 230 mm
x4 = 150 mm
Assuming As'=As Weight= 5.70 kgs
Assuming that Comp. And Tensile steel yields 0.06 KN
ΣFH=0 ; Pn+T = C + C'
Equation 1
Pn = 0.85fc'aB + As'fy - Asfy
ΣM@ the Tensile Steel
Equation 2
Pn (e+x1) = As'fyx2 + 0.85fc'aB (x3 – (a/2)) + As 2fyx3
Equating 1 and 2
a2 a
1785 + -140085.01 + -32000337.6
By Quadratic Formula
x = (-b (+/-) √ b^2 - 4 ac ) / 2a

140085 (+/-) 498102.6194

=
3570
taking + 178.764041 mm
taking - -100.28505 mm use 178.7640408 mm
Pn 638.1876256 KN
RESTRAINTS
Top Btm
Lu (mm) Braced ? k Le (mm) Slenderness
Cond Cond
X-AXIS 3600 F F N 1.2 4320 Lex/h = 14.40
Y-AXIS 3600 F F N 1.2 4320 Ley/b = 21.60

Page 1
 COLUMN1

Axis

Status

Column is
SLENDER

Page 2
 COLUMN2
DESIGN OF BOTTOM OUTER COLUMNS

Summary Results
Applied Moment Mu max = 150.14 KN-m RESULTS
Applied Axial Load Pumax = 1164.92 KN Ductile
Nominal Load 1664.17 KN 0
Fail 982.11 KN
Additional Reaction Mu= 0.00 KN-m
Pu= 0.00 KN
Cross-Section Dimensions
Height of Beam critical axis H= 400 mm X
Base of Beam B= 200 mm
Other Datas
Concrete Cover 70 mm
Bar Type Fc' = 21 Mpa
Fy = 275 Mpa
e= 128.88 mm
Bars Bar Pcs stirrups = 10 mm
16 4 corner mm
16 4 in between
As = 603.1872 mm2
As2 = 402.1248 mm2
x1 = 130 mm
x2 = 260 mm
x3 = 330 mm
x4 = 200 mm
Assuming As'=As Weight= 6.68 kgs
Assuming that Comp. And Tensile steel yields 0.07 KN
ΣFH=0 ; Pn+T = C + C'
Equation 1
Pn = 0.85fc'aB + As'fy - Asfy
ΣM@ the Tensile Steel
Equation 2
Pn (e+x1) = As'fyx2 + 0.85fc'aB (x3 – (a/2)) + As 2fyx3
Equating 1 and 2
a2 a
1785 + -253885.3 + -65244748.8
By Quadratic Formula
x = (-b (+/-) √ b^2 - 4 ac ) / 2a

253885.3 (+/-) 728220.6051

=
3570
taking + 275.099692 mm
taking - -132.86703 mm use 275.099692 mm
Pn 982.1059004 KN
RESTRAINTS
Top Btm
Lu (mm) Braced ? k Le (mm) Slenderness
Cond Cond

Page 1
 COLUMN2
X-AXIS 3000 F F N 1.2 3600 Lex/h = 9.00
Y-AXIS 3000 F F N 1.2 3600 Ley/b = 18.00

Page 2
 COLUMN2

Axis

Status

Page 3
 COLUMN2
Column is
SLENDER

Page 4
 COLUMN3
DESIGN OF BOTTOM CORNER COLUMNS

Summary Results
Applied Moment Mu max = 5.77 KN-m RESULTS
Applied Axial Load Pumax = 1.89 KN Ductile
Nominal Load 2.70 KN 0
Fail 0.00 KN
Additional Reaction Mu= 0.00 KN-m
Pu= 0.00 KN
Cross-Section Dimensions
Height of Beam critical axis H= 0.001 mm X
Base of Beam B= 0.001 mm
Other Datas
Concrete Cover 70 mm
Bar Type Fc' = 21 Mpa
Fy = 275 Mpa
e= 3057.31 mm
Bars Bar Pcs stirrups = 10 mm
16 4 corner mm
12 4 in between
As = 515.2224 mm2
As2 = 226.1952 mm2
x1 = -69.9995 mm
x2 = -139.999 mm
x3 = -69.999 mm
x4 = 0.0005 mm
Assuming As'=As Weight= 5.70 kgs
Assuming that Comp. And Tensile steel yields 0.06 KN
ΣFH=0 ; Pn+T = C + C'
Equation 1
Pn = 0.85fc'aB + As'fy - Asfy
ΣM@ the Tensile Steel
Equation 2
Pn (e+x1) = As'fyx2 + 0.85fc'aB (x3 – (a/2)) + As 2fyx3
Equating 1 and 2
a2 a
0.008925 + 54.5729745 + 19835889.61
By Quadratic Formula
x = (-b (+/-) √ b^2 - 4 ac ) / 2a

-54.57297 (+/-) #NUM!

=
0.01785
taking + #NUM! mm
taking - #NUM! mm use #NUM! mm
Pn #NUM! KN
RESTRAINTS
Top Btm
Lu (mm) Braced ? k Le (mm) Slenderness
Cond Cond
X-AXIS 3000 F F N 1.2 3600 Lex/h = ######
Y-AXIS 3000 F F N 1.2 3600 Ley/b = ######

Page 1
 COLUMN3

Axis

Status

Column is
FAILS

Page 2
 INNER SQUARE FOOTING
RC ISOLATED COLUMN FOOTING
Inner Footing

d
Edge 1

L
X
Summary Results

Pu 143.66 kN
Dimension
Footing Dimension L 1000 mm
W 1000 mm
Assumed Thickness t 250.00 mm
Assumed Depth d 164.00 mm
Soil Pressure 143.66 KN/m2
Allowable Soil Pressure 150.0 KN/m2
ok
Strength Reduction Factor 0.70
Bar Yield Strength 275 MPA
Concrete Compressive Strength 21.0 MPA
Concrete Cover 70.0 mm
Column Details
Column Dimension along Length 300 mm
Column Dimension along Width 200 mm
Column Distance from Edge1 500.00 mm
Depth required for One-Way Shear 41.16
Depth required for Punching Shear 55.53 mm
use d 164.00 mm
SHEAR AND MOMENT DIAGRAM

Page 1
 INNER SQUARE FOOTING

Design Moment 12.57 KN-m

Reinforcement Details
Actual Steel Ratio 2.03E-03
Balanced Steel Ratio 0.0378
Maximum Steel Ratio 0.0284
Minimum Steel Ratio 0.0051
Adapted Steel Ratio 0.0051
Bar Size to be used 16 mm
Bar Area 201.06 mm2
Steel Area 834.91 mm2
No. of Bars to be used 4.15 pcs
Adapted No. of Bars distributed both ways 5 pcs
spacing 168.8 mm

Engr. Leandro B. Piczon II

Page 2
 OUTER SQUARE FOOTING
RC ISOLATED COLUMN FOOTING
Outer Footing

d
Edge 1

L
X
Summary Results

Pu 619.63 kN
Dimension
Footing Dimension L 1300 mm
W 1300 mm
Assumed Thickness t 300.00 mm
Assumed Depth d 214.00 mm
Soil Pressure 366.64 KN/m2
Allowable Soil Pressure 150.0 KN/m2
change dimension
Strength Reduction Factor 0.70
Bar Yield Strength 275 MPA
Concrete Compressive Strength 21.0 MPA
Concrete Cover 70.0 mm
Column Details
Column Dimension along Length 400 mm
Column Dimension along Width 200 mm
Column Distance from Edge1 650.00 mm
Depth required for One-Way Shear 133.28
Depth required for Punching Shear 197.20 mm
use d 214.00 mm
SHEAR AND MOMENT DIAGRAM

Page 1
 OUTER SQUARE FOOTING

Moment Diagram (kN-m)

Design Moment 69.71 KN-m

Reinforcement Details
Actual Steel Ratio 5.22E-03
Balanced Steel Ratio 0.0378
Maximum Steel Ratio 0.0284
Minimum Steel Ratio 0.0051
Adapted Steel Ratio 0.0052
Bar Size to be used 16 mm
Bar Area 201.06 mm2
Steel Area 1452.09 mm2
No. of Bars to be used 7.22 pcs
Adapted No. of Bars distributed both ways 8 pcs
spacing 143.0 mm

Engr. Leandro B. Piczon II

Page 2
 CORNER SQUARE FOOTING
RC ISOLATED COLUMN FOOTING
Corner Footing
Edge 1

L
X
Summary Results

Pu 0.01 kN
Dimension
Footing Dimension L 0.001 mm
W 0.001 mm
Assumed Thickness t 300.00 mm
Assumed Depth d 214.00 mm
Soil Pressure 6647990378.15 KN/m2
Allowable Soil Pressure 150.0 KN/m2
change dimension
Strength Reduction Factor 0.70
Bar Yield Strength 275 MPA
Concrete Compressive Strength 21.0 MPA
Concrete Cover 70.0 mm
Column Details
Column Dimension along Length 0.001 mm
Column Dimension along Width 0.001 mm
Column Distance from Edge1 0.00 mm
Depth required for One-Way Shear -2191426115.37
Depth required for Punching Shear -150357585.88 mm
use d 214.00 mm
SHEAR AND MOMENT DIAGRAM

Shear Diagram (kN)

Page 1
 CORNER SQUARE FOOTING

Moment Diagram (kN-m)

Design Moment 0.00 KN-m

Reinforcement Details
Actual Steel Ratio 0.00E+00
Balanced Steel Ratio 0.0378
Maximum Steel Ratio 0.0284
Minimum Steel Ratio 0.0051
Adapted Steel Ratio 0.0051
Bar Size to be used 16 mm
Bar Area 201.06 mm2
Steel Area 0.00 mm2
No. of Bars to be used 0.00 pcs
Adapted No. of Bars distributed both ways 1 pcs
spacing -156.0 mm

Engr. Leandro B. Piczon II

Page 2
 SUMMARY
BEAM BASE HEIGHT BARS AT MIDSPAN
(mm) (mm) BOTTOM NUMBER 2ND LAYER
1 200.00 400.00 16.0 3.0 16.0
2 200.00 400.00 16.0 3.0 0.0
3 200.00 400.00 16.0 3.0 0.0
4 190.00 375.00 16.0 3.0 0.0
5 200.00 300.00 0.0 0.0 0.0
5A 200.00 400.00 16.0 3.0 20.0
6 200.00 300.00 16.0 4.0 0.0
6A 150.00 375.00 16.0 3.0 0.0
7 0.00 0.00 0.0 0.0 0.0
7A 200.00 400.00 16.0 3.0 20.0
8 0.00 0.00 16.0 3.0 0.0
9 0.00 0.00 0.0 0.0 0.0
10 0.00 0.00 0.0 0.0 0.0
11 0.00 0.00 0.0 0.0 0.0
12 0.00 0.00 0.0 0.0 0.0
13 0.00 0.00 0.0 0.0 0.0
14 0.00 0.00 0.0 0.0 0.0
15 0.00 0.00 16.0 2.0 0.0

COLUMN BASE HEIGHT BARS

(mm) (mm) CORNER NUMBER IN-BETWEEN
1 200.00 300.00 16.0 4.0 12.0
2 200.00 400.00 16.0 4.0 16.0
3 0.00 0.00 16.0 4.0 12.0

FOOTING BASE HEIGHT BARS

(mm) (mm) SIZE NUMBER BOTHWAYS
INNER 1000.00 1000.00 16.0 5.0
OUTER 1300.00 1300.00 16.0 8.0
CORNER 0.00 0.00 16.0 1.0

SLAB THK LONG SHORT MuL MuS

(mm) (mm) (mm) (Kn-M) (Kn-M)
1 100.00 5000.00 3700.00 0.89 3.14
REINFORCEMENT
DEVELOPMENT LENGHT LONG SHORT
(mm) (mm) (mm)
136 12 12
SPACING
LONG SHORT
(mm) (mm)
200 200

Page 1
 SUMMARY
BARS AT MIDSPAN MAX MOMENT MAX SHEAR
NUMBER TOP NUMBER (Kn-m) (Kn)
2.0 16.0 3.0 115.50 -92.05
0.0 16.0 3.0 77.34 -63.92
0.0 16.0 3.0 43.74 -34.74
0.0 16.0 3.0 39.24 -20.93
0.0 0.0 0.0 164.53 -107.60
2.0 17.6 5.0 166.55 -104.50
0.0 16.0 2.0 20.00 -92.04
0.0 16.0 3.0 150.14 -92.04
0.0 0.0 0.0 166.55 -104.50
2.0 17.6 5.0 166.55 -104.50
0.0 17.6 5.0 22.18 -14.27
0.0 0.0 0.0 22.18 -14.27
0.0 0.0 0.0 22.18 -14.27
0.0 0.0 0.0 22.18 -14.27
0.0 0.0 0.0 22.18 -14.27
0.0 0.0 0.0 22.18 -14.27
0.0 0.0 0.0 22.18 -14.27
0.0 0.0 0.0 22.18 -14.27

TIES PU MU
NUMBER (mm) (Kn) (Kn)
4.0 200 354.27 39.24
4.0 200 1164.92 150.14
4.0 0.001 1.89 5.77

THICK FOOTING REACTION

(mm) (Newtons)
250.00 143658.38
300.00 619626.43
300.00 6.65

MuE1 MuE2 MuE3 MuE4

(Kn-M) (Kn-M) (Kn-M) (Kn-M)
1.19 4.19 1.19 4.19
REINFORCEMENT
EDGE 1 EDGE 2 EDGE 3 EDGE 4
(mm) (mm) (mm) (mm)
12 12 12 12
SPACING
EDGE 1 EDGE 2 EDGE 3 EDGE 4
(mm) (mm) (mm) (mm)
200 200 200 200

Page 2