Basic Electrical Engineering Interview Questions

http://eeecore.weebly.com/short-notes.html

What is Current?
Current can be defined as the motion of charge through a conducting material. The unit of current is
Ampere whilst charge is measured in Coulombs.
Please define Ampere:-
The quantity of total charge that passes through an arbitrary cross section of a conduct-ing material per
unit second is defined as an Ampere.”
Mathematically,
I =Q/t
or Q = It
where Q is the symbol of charge measured in Coulombs (C), I is the current in amperes (A) and t is the
time in seconds (s).
Could you measure current in parallel?
No, Current is always measured through (in series with) a circuit element.
What is the difference between Voltages or Potential Difference? And what are they?
Voltage or potential difference between two points in an electric circuit is1V if 1J (Joule) of energy is
expended in transferring 1 C of charge between those points.
It is generally represented by the symbol V and measured in volts (V). Note that the symbol and the unit
of voltage are both denoted by the same letter; however, it rarely causes any confusion.
The symbol V also signifies a constant voltage (DC) whereas a time-varying (AC) voltage is represented
by the symbol v or v (t)
Could you measure Voltage in series?
No, Voltage is always measured across (in parallel with) a circuit element
How many Types of Circuit Loads are there in a Common Electrical Circuit?
A load generally refers to a component or a piece of equipment connected to the output of an electric
circuit. In its fundamental form, the load is represented by any one or a combination of the following:
1. Resistor (R)
2. Inductor (L)
3. Capacitor (C)
A load can either be of resistive, inductive or capacitive nature or a blend of them. For example, a
light bulb is a purely resistive load where as a transformer is both inductive and resistive. A circuit
load can also be referred to as a sink since it dissipates energy whereas the voltage or current supply can
be termed as a source.
What are the different Sign Conventions used in electric circuits?
It is common to think of current as the flow of electrons. However, the standard convention is to take the
flow of protons to determine the direction of the current.
In a given circuit, the current direction depends on the polarity of the source voltage. Current always flow
from positive (high potential) side to the negative (low potential) side of the source as shown in the
schematic diagram of Figure 2.4(a) where Vs is the source voltage, VL is the voltage across the load and I
is the loop current flowing in the clockwise direction.
 In Source current leaves from the positive terminal
In Load (Sink) current enters from the positive terminal.

What do you mean by Passive Circuit Elements and why these are called Passive?
Passive Circuit Elements :
Resistor, Capacitor, Inductor
State and define Ohm’s Law?
It is the most fundamental law used in circuit analysis. It provides a simple formula describing the
voltage-current relationship in a conducting material.
Statement:
The voltage or potential difference across a conducting material is directly proportional
to the current flowing through the material.
V∝I
V = RI or I =V/R
or R =V/I
where the constant of proportionality R is called the resistance or electrical resistance, measured in ohms
(Ω).
Please Define Ohm’s Law for A.C (Alternating Current)?
Everything else would remain same only the resistance will be replaced with Impedance, which is defined
as the opposition to the flow of A.C.
What is the function of Capacitor in Electrical Circuits?
A capacitor is a passive circuit element that has the capacity to store charge in an electric field. It is
widely used in electric circuits in the form of a filter.
Why Inductors are installed in electrical Circuits?
An inductor is a piece of conducting wire generally wrapped around a core of a ferromagnetic material.
Like capacitors, they are employed as filters as well but the most well known application is their use in
AC transformers or power supplies that converts AC voltage levels.

 Briefly explain the purpose of Inductor in an electric circuit?

An inductor is a piece of conducting wire generally wrapped around a core of a ferromagnetic material.
Like capacitors, they are employed as filters as well but the most well known application is their use in
AC transformers or power supplies that converts AC voltage levels.

 What do you mean by dependent and independent voltage sources?

In general, there are two main types of DC sources
1. Independent (Voltage and Current) Sources
2. Dependent (Voltage and Current) Sources

An independent source produces its own voltage and current through some chemical reaction and does
not depend on any other voltage or current variable in the circuit.
The output of a dependent source, on the other hand, is subject to a certain parameter (voltage or current)
change in a circuit element. Herein, the discussion shall be confined to independent sources only.

 Differentiate between ideal and non-ideal voltage sources?

The Ideal Voltage Source An ideal voltage source which has a terminal voltage which is independent of
the variations in load. In other words, for an ideal voltage source, the supply current alters with changes in
load but the terminal voltage, VL always remains constant.Non-Ideal or Practical Voltage Source For a
practical source, the terminal voltage falls off with an increase in load current.

 What does the term “Voltage Regulation” means?

 Voltage regulation (VR) is an important measure of the quality of a source. It is used to measure the
variation in terminal voltage between no load (IL =0, open circuit) and full load (IL = IFL)

 What is DC Current source? Differentiate between ideal and non ideal current sources?
 A current source, unlike the DC voltage source, is not a physical reality. How ever, it i s useful in
deriving equivalent circuit models of semiconductor devices such as a transistor. It can also be subdivided
into ideal and non-ideal categories.
The Ideal Current Source By definition, an ideal current source, that produces a current which is
independent of the variations in load. In other words the current supplied by an ideal current source does
not change with the load voltage.
Non-Ideal or Practical Current Source The current delivered by a practical current source falls off with an
increase in load or load voltage. What id difference between power and energy? Energy is defined as
the capacity of a physical system to perform work. In the context of electric circuits, energy (w) is related
to power by the following relationship p = vi =dw/dt
So the difference is that power is the rate of change of energy.

 What is Voltage Divider Rule?

Voltage divider rule provides a useful formula to determine the voltage across any resistor when two or
more resistors are connected in series with a voltage source.

 What is Kirchoff ’s Current Law (KCL)?

The algebraic sum of all the currents entering or leaving a node in an electric circuit is
equal to zero. In other words, the sum of currents entering is equal to the sum of currents leaving the node
in an electric circuit.

 What is Current Divider Rule (CDR)?

Current divider rule provides a useful relationship for determining the current through individual circuit
elements that are connected in parallel.

 What is Superposition Theorem?

Superposition theorem is extremely useful for analyzing electric circuits that contains two or more active
sources. In such cases, the theorem considers each source separately to evaluate the current through or
voltage across a component. The resultant is given by the algebraic sum of all currents or voltages caused
by each source acting independently. Superposition theorem can be formally stated
as follows:

“The current through or voltage across any element in a linear circuit containing several sources is the
algebraic sum of the currents or voltages due to each source acting alone, all other sources being removed
at that time.”

 Please elaborate Th´evenin’s Theorem?

Th´evenin’s theorem provides a useful tool when solving complex and large electric circuits by reducing
them to a single voltage source in series with a resistor. It is particularly advantageous where a single
resistor or load in a circuit is subject to change. Formally, the Th´evenin’s theorem can be stated as:

“Any two-terminal linear electric circuit consisting of resistors and sources, can be re-placed by an
equivalent circuit containing a single voltage source in series with a resistor connected across the load.”
he following steps outline the procedure to simplify an electric circuit using Th´evenin’s theorem
where VTH and RTH are the Th´evenin’s voltage and Th´evenin’s resistance respectively.
1. Remove the load resistance RL.
 2. VTH is the open circuit (OC) voltage across the load terminals and
3. RTH is the resistance across the load terminals with all sources replaced by their internal resistances.

 State and define Norton’s Theorem?

Th´evenin’s equivalent circuit is a practical voltage source. In contrast, Norton’s equivalent circuit is a
practical current source. This can be formally stated as:

“Any two-terminal, linear circuit, of resistors and sources, can be replaced by a single
current source in parallel with a resistor.”

To determine Norton’s equivalent circuit, Norton current, IN , and Norton resistance, RN , are required.
The following steps outline the procedure required:

1. Remove the load resistance, RL.

2. IN is the SC current through the load terminals and
3. RN is the resistance across the load terminals with all sources replaced by their internal resistances.
Clearly RN = RTH .

 What is the method to solve circuit using Source Transformation?

In an electric circuit, it is often convenient to have a voltage source rather than a current source (e.g. in
mesh analysis) or vice versa. This is made possible using source transformations. It should be noted that
only practical voltage and current sources can be transformed. In other words, a Th´evenin’s equivalent
circuit is transformed into a Norton’s one or vice versa. The parameters used in the source
transformation are given as follows.
Th´evenin parameters: VTH ,RTH =⇒ RN = RTH ,IN = VTH/RTH
Norton parameters: IN ,RN =⇒ RTH = RN ,VTH = RN IN
Any load resistance, RL will have the same voltage across, and current through it when connected across
the terminals of either source.

 What is Maximum Power Transfer Theorem?

As discussed in the section on Th´evenin’s theorem, any DC network of sources and resistances can be
replaced by a single voltage source in series with a resistance connected across the load:

The maximum power transfer theorem states that the power delivered to the load is maximum when the
load resistance, RL is equal to the internal (source) resistance, Rs of the DC power supply.

In other words, it can be said that the load resistance must match the Th´evenin’s resistance for maximum
power transfer to take place i.e.,
(Rs = RTH )= RL
When this occurs, the voltage across the load resistance will be Vs/2 and the power delivered to the load
is given by

which clearly demonstrates maximum power delivered when Rs = RL. Under this condition, the
maximum power will be:
 Define Super node?
A supernode exists when an ideal voltage source appears between any two nodes of an electric circuit.
The usual way to solve this is to write KCL equations for both nodes and simply add them together into
one equation ignoring the voltage source in question. However, this would mean one less equation than
the number of variables (node voltages) present in the circuit. A constraint equation can be easily
specified given by the magnitude of the ideal voltage source present between the nodes and the respective
node voltages. The following example will help clarify this scenario.

 What does the term Supermesh means?

A supermesh exists when an ideal current source appears between two meshes of an electric circuit. In
such a situation, like supernode, mesh equations are written for the meshes involved and added giving a
single equation. Again, there would be one less equation than the number of variables (mesh currents) and
hence a constraint equation is needed. This would be based on the magnitude of the ideal current source
present between the two meshes and their mesh currents.

 What do you mean by Phasors?

Addition of two out-of-phase sinusoidal signals is rather complicated in the time domain. An example
could be the sum of voltages across a series connection of a resistor and an inductor.
Phasors simplify this analysis by considering only the amplitude and phase components of the sine wave.
Moreover, they can be solved using complex algebra or treated vectorially using a vector diagram.

 What does the term Power Factor shows?

The term cos φ is called the power factor and is an important parameter in determining the amount of
actual power dissipated in the load. In practice, power factor is used to specify the characteristics of a
load.

For a purely resistive load φ =0 Degree, hence Unity Power Factor

For a capacitive type load I leads V , hence Leading power factor
For an inductive type load I lags V , hence Lagging power factor

Clearly, for a fixed amount of demanded power, P , at a constant load voltage, V , a higher power factor
draws less amount of current and hence low I2R losses in the transmission lines. A purely reactive load
where φ → 900 and cos φ → 0 will draw an excessively large amount of current and a power factor
correction is required.

 Differentiate between Real and Apparent Power?

It is important to highlight that in AC circuits, the product of voltage and current yields the apparent
power which is measured in volt-amperes or VA

KW which is also written ad Kilo-Watt is the real power that is actually converted to the useful work.

KVAR is also termed as Kilo-Volt Reactive this power is used for magnetic field excitation and flows
back and forth between source and load.
 What does Bode Plots shows?
Bode plots are a graphical way to display the behavior of a circuit over a wide range of frequencies. By
plotting the amplitude and phase versus the logarithm of frequency, each unit of change on the ω axis is
equal to a factor of 10 also called a decade of frequency. Also, there may be a wide distribution in the
 amplitude response over a specified range of frequencies. The usual way is to plot the amplitude in dB
and phase in degrees or radians versus the logarithm of frequency.

 Differentiate between Low Pass, High pass and Band Pass filter?
Filters form a vital part in electrical networks especially where a particular frequency range is of prime
concern. For instance, a radio station is broadcasting a transmission at a frequency of 100 MHz. This
means that it is required to design a receiving filter which allows only 100 MHz frequency to pass hrough
whilst other frequencies are filtered out. An ideal filter will attenuate all signals with frequencies less than
and greater than 100 MHz thus providing the best channel sound quality without any distortion.
Low Pass Filter
A low pass Filter allows low frequencies to pass through the circuit whereas high frequencies are severely
attenuated or blocked.
High Pass Filter
A high pass filter, as the name suggests, allows high frequencies to pass through the circuit whilst low
frequencies are attenuated or blocked. The cut-off point or bandwidth concept is the same as in the low
pass filter.
Band Pass Filter
A band pass filter permits a certain band of frequencies to pass through the network which is adjusted by
the designer. It is simply an amalgamation of a low pass and a high pass filter.

 What is Corkscrew Rule?

As current flows along a wire, the magnetic field rotates in the direction of a corkscrew.

 What does Ampere turns shows?

mmf A coil of N turns carrying a current I amps gives an mmf of N I ampere turns In a vacuum, a
magnetizing force of 1 ampere turn / metre produces a magnetic field of 1.26*10^-6 tesla.

 Differentiate between Magnetic field and Magnetic Flux?

Magnetic field is B = µ H where B is in tesla and H = 1.26 x 10-6 times ampere turns/metre MMF in a
solenoid of N turns and current I mmf = (4 m / 10) N I Gilberts.
Whereas Magnetic flux ø= B A where ø is in weber, B is in tesla and A is in square meters.
Magnetic flux in a uniform closed magnetic circuit, length L meters and cross section A square meters is
=1.26NItAx10^-6/Lweber.

 What is Force on a conductor in a magnetic field ?

F = B I L Newtons where B in tesla, I in amps and L in meters

 What is force on parallel conductors ?

F = [2 I2 / d] 10-' Newtons/meter where I is in amps and d is in meters With currents in opposite
directions, the force is pushing the conductors apart

 What do you mean by Pull of Electromagnet?

Pu11= B2 107 / (8 ) Newtons per m2 of magnet force where B is in tesla

 How would you calculate Power loss in a resistor?

W = I2 R = V2 / R

 At what factor Resistance R of a conductor depends?

R = p L (1 + αT) / A ohms where p is resistivity in ohms per cm cube, L cm is the length, A in cm2 is the
cross sectional area, α is temp co-efficient and T is the temperature in degrees Celsius.
 Several sources give Copper p = 1.7 * 10-6 ohms per cm cube and α = 0.004. At very low Temperatures,
the resistance of some materials falls to zero

 Differentiate between Kirchhoff’s First law and Kirchhoff’s Second law?

Kirchhoff’s First law is the total current leaving a point on an electrical circuit = total current entering
Kirchhoff’s Second law The sum of the voltages round any circuit = net "I R" drop in the circuit

 Differentiate between Induced emf and Self inductance?

Induced emf , E = - N dø/dt where E is in volts, N is number of turns and dø/dt is in Wb/sec This
equation is the foundation on which Electrical Engineering is based.
Whereas Self Inductance E = - L dI/dt where E is in volts, L is inductance in henneries and dI/dt is in
amps/sec Self inductance of a coil wound on a ring of permeability is L = 1.26 N2 μ A / S x 10-6
Henneries where N is number of turns, A is cross sectional area in m2 and S meters is the length of the
magnetic circuit. Experimental results for a coil of length S meters, diameter d meters and radial thickness
t meters with at core indicate L = 3 d2 N2 / (1.2 d + 3.5 S + 4 t) micro Henneries. (t = 0 for a single layer
coil).

 How to calculate Energy stored in an inductance?

Energy stored =1/2 L I2 Joules where L is in henries and I is in amps

 How to calculate Energy stored in a capacitance

= 1/2 C V2 Joules where C is in farads and V in volts

 At what base you will tell the direction of rotation of DC Motors and Generators?

Motors obey the left hand rule and generators the right hand rule