Scribd
Upload
116 views

An124 Tuning Control Loops With The IMC Tuning Method PDF

Uploaded by

Syed Mian Fahim Kakakhail
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
116 views

An124 Tuning Control Loops With The IMC Tuning Method PDF

Uploaded by

Syed Mian Fahim Kakakhail
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

AN124 Dataforth Corporation Page 1 of 3

DID YOU KNOW ?


When PI and PID controllers first came to market during the 1930s, there were no clear instructions on how to tune them.
Tuning was done through trial and error and results were inconsistent. This was the situation until 1942, when J. G. Ziegler
and N. B. Nichols from the Taylor Instruments Company published two methods for tuning PID controllers [Ref. 1]. These
tuning rules came into widespread use while Ziegler and Nichols became legends among process control practitioners.

Tuning Control Loops with the IMC Tuning Method


Preamble Advantages and Disadvantages of IMC Tuning
Since 1942, well over one hundred controller tuning The IMC tuning method offers the following advantages:
methods have been developed, each trying to accomplish Once tuned using the IMC tuning rules, the
a certain objective or fill a specific niche. One of these process variable will not overshoot its set point
methods is the Internal Model Control (IMC) tuning after a set point change.
method [Ref. 2], sometimes called Lambda tuning. It The IMC tuning rules are much less sensitive to
offers a stable and robust alternative to other techniques, possible errors made when determining the
such as the famous Ziegler-Nichols method, that usually process dead time through step tests. It is easy to
aim for speed at the expense of stability. This Application under- or over-estimate dead time on lag-
Note describes how to tune control loops using IMC dominant processes because of their relatively
tuning rules. short dead times. Ziegler-Nichols and many
other tuning rules can give poor results when the
Applicable Process Types dead time is measured incorrectly.
The IMC tuning method was developed for use on self- The tuning is very robust, meaning that the
regulating processes. Most control loops, e.g., flow, control loop will remain stable even if the
temperature, pressure, speed, and composition, contain process characteristics change substantially from
self-regulating processes. One obvious exception is a the ones used for tuning.
level control loop, which contains an integrating process. An IMC-tuned control loop absorbs disturbances
better and passes less of them on to the rest of
A self-regulating process always stabilizes at some point the process. This is a very attractive
of equilibrium, which depends on the process design and characteristic for using IMC tuning in highly
the controller output. If the controller output is set to a interactive processes.
different value, the process will respond and stabilize at a The user can specify the desired control loop
new point of equilibrium (Figure 1). response time (the closed-loop time constant).
This provides a single “tuning factor” that can be
used to speed up and slow down the loop
response.

Unfortunately, the IMC tuning method has a drawback,


too. It sets the controller’s integral time equal to the
process time constant. If a process has a very long time
constant, the controller will consequently have a very
long integral time. Long integral times make recovery
from process disturbances very slow.

Target Controller Algorithm


The IMC tuning rules are designed for use on a
noninteractive controller algorithm. The tuning rules
presented here are for a PI controller. Although IMC
Figure 1 tuning rules have also been developed for PID controllers,
A Self-regulating Process Settles Out at New Level there is theoretically no difference in the speed of
after Change in Controller Output response of the PI and PID tuning rules, so there is little
sense in adding the complexity of derivative control.
AN124 Dataforth Corporation Page 2 of 3

Procedure
To apply the IMC tuning rules for a self-regulating
process, follow the steps below. The process variable and
controller output must be time-trended so that
measurements can be taken from them (Figure 2).

1. Do a step test:
a) Put the controller in manual and wait for the
process to settle out.
b) Make a step change in the controller output
(CO) of a few percent and wait for the
process variable (PV) to settle out. The size
of this step should be large enough that the
PV moves well clear of the process
noise/disturbance level. A total movement of Figure 2
five times more than the peak-to-peak level Step Test for IMC Tuning
of the noise and disturbances on the PV
should be sufficient. 3. Repeat steps 1 and 2 three more times to obtain
good average values for the process
2. Determine the process characteristics (refer to characteristics.
Figure 2):
a) If the PV is not ranged 0-100%, convert the 4. Choose a desired loop response time (closed
change in PV to a percentage of the range as loop time constant, cl) for the control loop.
follows: Generally, the value for cl should be set between
Change in PV [in %] = change in PV [in one and three times the value of . Use cl = 3 ×
Eng. Units] × 100 / (PV upper calibration for a very stable control loop. Using a larger
limit - PV lower calibration limit) value for cl will result in a slower control loop,
b) Calculate the Process Gain (gp): while using a smaller value will result in a faster
gp = total change in PV [in %] / change in control loop.
CO [in %]
c) Find the maximum slope of the PV response 5. Calculate PID controller settings using the
curve. This will be at the point of inflection. equations below.
Draw a tangential line through the PV
response curve at this point. For PI Control
d) Extend this line to intersect with the original Controller Gain, Kc = / ( gp × [ cl + td] )
level of the PV before the step in CO. Integral Time, Ti =
e) Take note of the time value at this inter- Derivative Time, Td = 0
section and calculate the Dead Time (td):
td = time difference between the change in
CO and the intersection of the tangential line 6. Enter the values into the controller, make sure
and the original PV level the algorithm is set to Noninteractive, and put
f) If td was measured in seconds, divide it by the controller in automatic mode.
60 to convert it to minutes. Since the
Dataforth PID controller uses minutes as its 7. Change the set point to test the new values.
time base for integral time, all measure-
ments have to be made in minutes. 8. Do fine tuning if necessary. The control loop’s
g) Calculate the value of the PV at 63% of its response can be sped up by increasing Kc and/or
total change. decreasing Ti.
h) On the PV reaction curve, find the time
value at which the PV reaches this level.
i) Calculate the Time Constant ( ):
= time difference between intersection at
the end of dead time, and the PV reaching
63% of its total change
j) If was measured in seconds, divide it by 60
to convert it to minutes.
AN124 Dataforth Corporation Page 3 of 3

References
[1] J.G. Ziegler and N.B. Nichols, Optimum settings for
automatic controllers, Transactions of the ASME, 64, pp.
759–768, 1942

[2] D.E. Rivera, M. Morari, and S. Skogestad, Internal


Model Control. 4. PID Controller Design, Industrial
Engineering and Chemical Process Design and
Development, 25, p. 252, 1986

The reader is encouraged to visit Dataforth’s website to


learn more about PID control and the MAQ®20.

1. Application Note 122: Introduction to PID Control


Figure 3 http://www.dataforth.com/catalog/pdf/AN122.pdf
A Flow Control Loop, Tuned with IMC Method,
Responding to Set Point Change 2. MAQ®20 Brochure
http://www.dataforth.com/catalog/pdf/MAQ20_broch
Conclusion ure.pdf
While many PID controller tuning rules aim for a fast
response but sacrifice loop stability to obtain that fast
response, the IMC tuning rules provide a viable
alternative when control loop stability is important.

You might also like