Scribd
Upload
41 views3 pages

Experiment No 1 Aggregate Impact Value Test

This document describes a test to determine the aggregate impact value of different coarse aggregate samples according to BS 812. The aggregate impact value test subjects an aggregate sample to standard impacts from a falling weight to measure its resistance to shock or impact. An aggregate impact value below 10 is considered strong, while a value above 35 would be too weak for use in road surfaces. The test procedure involves compacting an aggregate sample in a cup, subjecting it to 15 blows from a falling 14 kg hammer, then sieving and weighing the fraction that passes through a No. 7 sieve to calculate the aggregate impact value as a percentage.

Uploaded by

Ali Asad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
41 views3 pages

Experiment No 1 Aggregate Impact Value Test

This document describes a test to determine the aggregate impact value of different coarse aggregate samples according to BS 812. The aggregate impact value test subjects an aggregate sample to standard impacts from a falling weight to measure its resistance to shock or impact. An aggregate impact value below 10 is considered strong, while a value above 35 would be too weak for use in road surfaces. The test procedure involves compacting an aggregate sample in a cup, subjecting it to 15 blows from a falling 14 kg hammer, then sieving and weighing the fraction that passes through a No. 7 sieve to calculate the aggregate impact value as a percentage.

Uploaded by

Ali Asad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Experiment No.

4
Statement:Determination of the aggregate impact value of different coarse aggregate
samples. (BS 812)

Scope & significance: Aggregate Impact Value


The aggregate impact value gives a relative measure of the toughness or the resistance of aggregate
sudden shock or impact is not proportional to the resistance to a slowly applied compressive
load. Aggregate Impact Value
Related Theory:
Aggregate Impact Value:
AIV is the percentage of fines produced from the aggregate sample after subjecting it to a standard
amount of impact. Aggregate Impact Value
The standard amount of impact is produced by a known weight, i.e. a steel cylinder, falling a set
height, a prescribed number of times, onto an amount of aggregate of standard size and weight retained in
a mould.
Aggregate Impact Values, (AIV’s), below 10 are regarded as strong, and AIV’s above 35 would
normally be regarded as too weak for use in road surfaces.
Aggregate Impact Values and Aggregate Crushing Values are often numerically very similar, and
indicate similar aggregate strength properties.
pact Value
Test Specifications:
The test sample shall consist of aggregates the whole of which passes through ½ in B.S. test sieve and
is retained on a 3/8 in B.S. test sieve. The aggregate comprising the test sample shall be dried in an oven
for a period of four hours at a temperature of 100-110 °C and cooled.The measuring cup shall be filled
about one-third with the aggregate and gives 25 no. of blows with tamping rod. A further similar quantity
of aggregate shall be added and a further 25 tamping given to the second and tot the last layer 25 tamping
shall again be given and the surplus aggregate struck off using the tamping rod as a straight-edge. The net
weight of aggregate in the measure shall be determined to the nearest gram (weight A) and this weight
shall be used for the duplicate test on the same material.The length of tamping rod is 600 mm and 16mm.

Apparatus: Aggregate Impact Value


1. Coarse aggregate from various sources
2. Impact testing machine
3. Spanner
4. Balance
Procedure:
The cup shall be fixed firmly in position on the base of the machine and the whole of the test sample
will be placed in it and compacted by a single tamping of 25 strokes of the tamping rod. The hammer of
14 kg shall be raised until its lower face is 15 in. above from the upper surface of the aggregate in the cup,
and allowed to fall freely on the aggregate. The test sample shall be subjected to a total 15 such blows
each being delivered at an interval of not less than one second. The crushed aggregate shall then be
removed from the cup and the whole of it sieved on No. 7 B.S. sieve until no further significant amount
passes in one minute. The fraction passing the sieve shall be weighted to an accuracy of 0.1 gram (weight
B). Te fraction retained on the sieve shall also be weighed (weight C), and if the total weight B + C is less
than the initial weight (weight A) by more than 1 gm the result shall be discarded and a fresh test made.
Two tests shall be made. Aggregate Impact Value
Calculations:
The ratio of the weight of fines formed to the total sample weight in each test shall be expressed as a
percentage, the result being recorded to the first decimal place. Aggregate Impact Value
Aggregate Impact Value = (B/A)*100
where
A = weight of oven dried sample Aggregate Impact Value
B = weight of fraction passing B.S. sieve No. 7

Observations & Results:


A=Total Wt. of the Sample
B = Fraction passing BS sieve #7 after crushing Aggregate Impact Value
Aggregate Impact Value = (B/A)*100
Cup Diameter =4 inches
Depth of Cup =5 inches
Weight of Hammer = 14 lbs
Drop Height = 15 inches

You might also like