Electromechanical Relays

Selection Guide
Latching Non-Latching
JAN

m
co
s.Commercial
nt
RF
ne
po
m

Established Surface-Mount
co

Reliability
e
lin
on

Environmental

Attenuated
Switching Solutions
Teledyne Relays has been the world’s innovative leader Product Assurance
in the manufacture of ultraminiature, hermetically sealed, Under an aggressive Total Quality Management (TQM)

m
electromechanical and solid-state switching products program, Teledyne Relays has embraced a “continuous
for more than 40 years. The company’s comprehensive improvement” culture. With recognized certifications such

co
product line meets a wide range of requirements for as AS/EN/JISQ 9100 - Revision B and ISO 9001:9002,
defense and aerospace, industrial, commercial, medical DSCC MIL-STD-790 and Boeing D6-82479 Appendix
and RF & wireless applications.
s.
A, Teledyne Relays has become a primary supplier of
nt
Business Focus switching solutions with the highest quality and reliability
• MIL QPL & COTS Solid-State Relays to industry leaders around the world.
ne

• MIL QPL & COTS Electromechanical Relays

• HiRel (Space) Electromechanical Relays Technical Service & Customer Support
po

• RF & Microwave Relays & Coaxial Switches Teledyne Relays provides easy access to technical
• Industrial Solid-State Relays service and customer support. Our websites make it easy
• Switching Matrices to find technical information, buy products and even get
m

Markets e-mail responses within 24 hours. Switching solutions

co

• Commercial & Military Aviation are only a mouse click away at www.teledynerelays.com
• Defense & Aerospace or at teledyne-europe.com. Information about coax
• Telecom/Communications (Wireless) switches is available at www.teledynecoax.com.
e

• Instrumentation & Test

lin

• Industrial Power & Motion Control

• Medical Applications
on

Teledyne Relays offer superior signal integrity up to

12 Gbps. See the RF relays section in our website.
 Table of Contents
RF RELAYS
Series Description Page
  RF100/RF103 High Repeatability, Broadband Centigrid® Relays, Non-Latching DPDT 4

  GRF172 Surface-Mount Centigrid® RF Relays, Non-Latching DPDT 4

  RF300/RF303 High Repeatability, Broadband TO-5 Relays, Non-Latching DPDT 5

  RF312 High Repeatability, Broadband TO-5 Relays, Non-Latching DPDT 6

  RF311/RF331 High Repeatability, Broadband TO-5 Relays, Non-Latching SPDT 7

  GRF342 Surface-Mount TO-5 RF Relays, Magnetic-Latching DPDT 7

m
  RF180 Broadband RF Relays, Magnetic-Latching DPDT 8

  RF341 Broadband TO-5 RF Relays, Magnetic-Latching SPDT 8

co
  RF310/RF313 High Repeatability TO-5 Relays, Normally Closed, Bypass 9

s.
  RF320/RF323 High Repeatability TO-5 Relays, Normally Open, Bypass 9
nt
  A150 Broadband Attenuator RF Relay 10
ne

  A152 Broadband Attenuator RF Relay 10

COMMERCIAL RELAYS
po

  122C Centigrid® Relays (CMOS Compatible), Magnetic-Latching DPDT 11

  172
m

Centigrid® Relays, Non-Latching DPDT 11

  712 TO-5 Relays, Non-Latching DPDT 12

co

  722 TO-5 Relays, Magnetic-Latching DPDT 12

e

  732 TO-5 Relays, Non-Latching Sensitive DPDT 13

lin

COMMERCIAL SURFACE-MOUNT RELAYS

on

  S114 Surface-Mount Centigrid® Relays, Non-Latching DPDT 14

  S134 Surface-Mount Centigrid® Relays, Non-Latching Sensitive DPDT 14

  S172 Surface-Mount Centigrid® Relays, Non-Latching DPDT 15

  S422 Surface-Mount TO-5 Relays, Magnetic-Latching DPDT 15

ESTABLISHED RELIABILITY RELAYS

  ER114 Centigrid® Relays, Non-Latching DPDT 16

  ER116C Centigrid® Relays (CMOS Compatible), Non-Latching DPDT 16

  ER134 Centigrid® Relays, Non-Latching Sensitive DPDT 17

  ER136C Centigrid® Relays (CMOS Compatible), Non-Latching Sensitive DPDT 17

See specific series for additional features and options Continued on next page

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 1

 Table of Contents
ESTABLISHED RELIABILITY RELAYS (continued)
Series Description Page
  ER411 TO-5 Relays, Non-Latching SPDT 18

  ER431 TO-5 Relays, Non-Latching Sensitive SPDT 18

  ER412 TO-5 Relays, Non-Latching DPDT 19

  ER432 TO-5 Relays, Non-Latching Sensitive DPDT 19

  255 Half-Size Crystal Can, Magnetic-Latching DPDT 20

  ER421 TO-5 Relays, Magnetic-Latching SPDT 20

  ER420 TO-5 Relays, Magnetic-Latching DPDT 21

m
  ER422 TO-5 Relays, Magnetic-Latching DPDT 21

co
MILITARY QUALIFIED (JAN) RELAYS

s.
  J114 Centigrid® Relays, Non-Latching DPDT nt 22

  J116C Centigrid® Relays (CMOS Compatible), Non-Latching DPDT 22

  J134 Centigrid® Relays, Non-Latching Sensitive DPDT 23

ne

  J136C Centigrid® Relays (CMOS Compatible), Non-Latching Sensitive DPDT 23

po

  J411 TO-5 Relays, Non-Latching SPDT 24

  J431 TO-5 Relays, Non-Latching Sensitive SPDT 24

m

  J412 TO-5 Relays, Non-Latching DPDT 25

co

  J432 TO-5 Relays, Non-Latching Sensitive DPDT 25

  J255 Half-Size Crystal Can, Magnetic-Latching DPDT 26

e
lin

  J421 TO-5 Relays, Magnetic-Latching SPDT 26

  J420 TO-5 Relays, Magnetic-Latching DPDT 27

on

  J422 TO-5 Relays, Magnetic-Latching DPDT 27

HIGH-PERFORMANCE RELAYS

  412H/432H High-Temperature (200°C) TO-5 Relays, Non-Latching DPDT 28

  422H High-Temperature (200°C) TO-5 Relays, Magnetic-Latching DPDT 28

  412K High-Shock TO-5 Relays, Non-Latching DPDT 29

  422K High-Shock TO-5 Relays, Magnetic-Latching DPDT 29

  412V/432V High-Vibration TO-5 Relays, Non-Latching DPDT 30

See specific series for additional features and options Continued on next page

Page 2 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 Table of Contents
APPENDIX
Description Page
Signal Integrity Eye Diagrams 31-38

RoHS and Reach Certificate of Compliance 39

Part Numbering System 40-41

Spacer Pad Options 42

Spreader Pad Options 43

Ground Pin Options 44

Established Reliability Program 45-46

m
Teledyne Relays HI-REL Program 47

co
Authorized Distributors 48

s.
Authorized North American Representatives nt 49
ne

Teledyne Relays offers a variety of options to

po

customize and meet your specific design needs.

m
e co

GRF Option SGRF Option GRF Option

TO-5 Relays with straight TO-5 Relays with Gull-Wing Centigrid® Relays with
lin

butt pins for surface-mount (J-Lead) pins for surface- straight butt pins for
applications mount applications surface-mount applications
* RF Relays Only * RF Relays Only * RF Relays Only
on

SGRF Option SRF Option /S Option

TO-5 Relays with Gull-Wing Relays with Gull-Wing Relays with 0.187”
(J-Lead) pins for surface- (J-Lead) pins for surface- trimmed leads
mount applications mount applications See Appendix: Part Numbering
* RF Relays Only * RF Relays Only System

Spacer Pad Option Spreader Pad Option /Q, /R Option

Relays with polyester film pad Relays with Diallyl Phthalate Relays with solder dipped
to space between PCB and pad to spread pins leads. Pb/Sn (60/40) or
Relay Header See Appendix: Spreader Pad
Options RoHS solder available
See Appendix: Spacer Pad Options See Appendix: Part Numbering System

See specific series for additional features and options

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 3

 RF RELAYS

Series RF100/RF103 Electromechanical Relays

The RF100 and RF103 Centigrid® relays are designed to provide improved RF signal repeatability over the • Excellent Signal integrity up to 10Gbps
frequency range. • Hermetically Sealed
The GRF100 and GRF103 Centigrid® relays feature a unique ground shield that isolates and shields each • High Resistance to ESD
lead to ensure excellent contact-to-contact and pole-to-pole isolation. This ground shield provides a ground • Metal Enclosure for EMI shielding
• High Repeatability
interface that results in improved high-frequency performance as well as parametric repeatability.
• Broader bandwidth
The SGRF100 and SGRF103 Centigrid® relays extend performance advantages over similar RF devices that • Through-hole or surface-mount
simply offer formed leads for surface mounting. configurations
RF

Relay Type Nominal Coil Typical RF Performance

  DPDT Non-Latching Part No. Isolation (dB)
Voltage Resistance Frequency VSWR Insertion Loss
Coil Type (Vdc) (Ω) (GHz) (max) Pole to Pole Across Contacts (dB) (max)
(min) (min)
  100 = Standard Coil
5 50 DC-1 1.1 : 1 35 25 0.2
  103 = Sensitive Coil RF100

m
12 390 1-2 1.5 : 1 30 20 0.5
Mounting
  RF = Thru-hole 5 100 2-3 1.6 : 1 30 20 0.6

co
  GRF = Surface-Mount (Stub) RF103
12 800
  SGRF = Surface-Mount (J-Lead)
5 50 DC-1 1.1 : 1 45 30 0.2
Temperature
RF100/RF103

s.
RF180/GRF180
GRF100
GRF100/GRF103 12 390 1-3 1.2 : 1 40 25 0.3
  Storage: –65°C
SGRF100/SGRF103
to +125°C COIL B

172
  Operating: –55°C to +85°C
nt
5 100 3-4 1.3 : 1 35 25 0.6
9
10 – GRF103
1
12 800 4-6 2.2 : 1 30 25 1.2
ne
8
2
+
5 50 DC-1 1.2 : 1 35 30 0.2
7 1 3
8
7 SGRF100
+
6 2
100 6
4 12 390 1-3 1.3 : 1 30 30 0.7
103 5
–
po

5 4 3
5 100 3-4 1.4 : 1 25 25 0.8
SGRF103
SCHEMATIC
COIL A
12 800 4-6 1.8 : 1 25 25 1.0
(Bottom View)
SCHEMATIC
(Coil B Last Energized)
m

(Bottom View)

Series GRF172 Electromechanical Relays

The GRF172 Centigrid® relay is a hermetically sealed, armature relay for 2.5GHz RF applications. Its low RF100/RF103
co

• Excellent Signal integrity up to 10Gbps RF180/GRF180

profile height .330” (8.38 mm) and .100” (2.54 mm) grid spaced terminals make it an ideal choice where GRF100/GRF103
• Hermetically Sealed
SGRF100/SGRF103
COIL B

extreme packaging density and/or close PC board spacing are required. The GRF172 features a unique
GRF172D A150/GA150 172• High Resistance to ESD
ground
S172D shield that isolates and shields each lead to ensure excellent contact-to-contact and pole-to-
A152/GA152 • Metal Enclosure for EMI shielding
e

10 –
pole isolation. This ground shield provides a ground interface that results in improved high-frequency • High Repeatability 9 1

performance as well as parametric repeatability. The GRF172 extends performance advantages over similar • Broader bandwidth
lin

8
2
3
RF devices that simply offer formed leads for surface 5
mounting. +
• Through-hole or surface-mount
7 1 3
The Series GRF172D has an internal discrete silicon diode for coil suppression. 6
configurations
8
2
7 +
8 2 6
7 1 6
4
on

–
5
5 4
6 2
RF3 Performance
Attenuator Pad
Relay Type 1 7 Nominal Coil Typical
5 3
  DPDT4Non-Latching Part No. Isolation (dB) Insertion Loss
COIL A
Voltage Resistance Frequency VSWR SCHEMATIC SCHEMATIC
(Ω)
(Bottom View)
Coil Type (Vdc) (GHz) (max) Pole to Pole Across Contacts (dB) (max)(Coil (Bottom
B Last Energized)
SCHEMATIC (min) (min) View)
(Bottom View)
  172 = Standard Coil SCHEMATIC
(Bottom View)
5 50 DC-1 1.1 : 1 45 30 0.2
Diode Option
GRF172
  D = Internal diode for coil 12 390 1-2 1.2 : 1 40 25 0.3
GRF172D A150/GA150
114, 134 GRF172D
  transient suppression
26
S114/S134 100 2-2.5 1.2 : 1 S172D 40 114D, 134D 25 0.3 A152/GA152
Mounting 172 S114D/S134D
172D
  GRF = Surface-Mount (Stub) 3 5

Temperature 7 1 8 8 2 6
7 71
8 1
  Storage: –65°C to +125°C 6 2
6
62
Attenuator Pad
2 1 7
  Operating: –55°C to +85°C 4
5 3 5
4 53 3
4

SCHEMATIC SCHEMATIC
GRF172 (Bottom View)SCHEMATIC
GRF172D
(Bottom View) (Bottom View) SCHEMATIC
(Bottom View)
Schematics as viewed from terminals 114DD, 134DD
S114DD/S134DD

8
Page 4 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com
7 1 © 2010 TELEDYNE RELAYS
6 2

5
 RF RELAYS

Series RF300/RF303 Electromechanical Relays

The RF300 and RF303 TO-5 relays are designed to provide improved RF signal repeatability over the • Excellent Signal integrity up to 10Gbps+
frequency range. • Hermetically Sealed
The GRF300 and GRF303 TO-5 relays feature a unique ground shield that isolates and shields each lead • High Resistance to ESD
to ensure excellent contact-to-contact and pole-to-pole isolation. This ground shield provides a ground • Metal Enclosure for EMI shielding
• High Repeatability
interface that results in improved high-frequency performance as well as parametric repeatability.
• Broader bandwidth
The SGRF300 and SGRF303 TO-5 relays extend performance advantages over similar RF devices that • Through-hole or surface-mount
simply offer formed leads for surface mounting. configurations

Relay Type Nominal Coil Typical RF Performance

  DPDT Non-Latching Part No. Isolation (dB)
Voltage Resistance Frequency VSWR Insertion Loss
Coil Type (Vdc) (Ω) (GHz) (max) Pole to Pole Across Contacts (dB) (max)
(min) (min)
  300 = Standard Coil
RF300 5 50 DC-1 1.1 : 1 30 25 0.2
  303 = Sensitive Coil

m
RF300D 12 390 1-2 1.1 : 1 25 20 0.3
Diode Option
  D = Internal diode for coil RF303 5 100 2-3 1.2 : 1 25 20 0.4

co
  transient suppression RF303D 12 850
  DD = Internal diode for coil
GRF300 5 50 DC-1 1.1 : 1 40 30 0.2

s.
  transient suppression and
GRF300D 12 390 1-3 1.1 : 1 40 30 0.2
  polarity reversal protection
nt
Mounting GRF303 5 100
411/431 3-4 1.3 : 1
411D/431D 30 30
411DD/431DD 0.6 411T/431T
411/431 411/431 411D/431D 411D/431D 411DD/431DD 411DD/431DD 411T/431T 411T/431T
  RF = Thru-hole GRF303D 12 850 4-6 1.6 : 1 25 25 1.0
  GRF = Surface-Mount (Stub)
ne

4 1 4 4 9 1
  SGRF = Surface-Mount (J-Lead) 4 SGRF300
1 4 51 4 50
5 4 DC-1 4
1.2
5 : 11 4
5
40 9
5 3011 9 1 0.2 2
5 1 5 1 5 1 2 8
5 5 1 2 8
8 3
  SRF = Surface Mount (J-Lead) SGRF300D 12 3 390 2 1-3 1.2 : 12 40 30
3 2 7 3 0.4 7
3 2 3 7 3
3 2 3 2 3 2 6 4
3 2
Temperature
po

3 2 6 6 4
4
SGRF303 5 100 3-4 1.2 : 1 20 25 0.8
  Storage: –65°C to +125°C SCHEMATIC SCHEMATIC SCHEMATIC
SCHEMATIC SCHEMATIC
(Bottom View) SCHEMATIC SCHEMATIC
SGRF303D
SCHEMATIC 12
(Bottom View) 850 4-6
(Bottom View)
SCHEMATIC
(Bottom View)
1.8 : 1 (Bottom10
View)
(Bottom View)
20 1.0
SCHEMATIC
SCHEMATIC
  Operating: –55°C to +85°C (Bottom View) (Bottom View) (Bottom View) SCHEMATIC (Bottom View)
(Bottom View)
(Bottom View)
m

SRF300 5 50 DC-1 1.1 : 1 25 25 0.5

SRF300D 12 390 1-3 1.5 : 1 25 25 0.5
co

SRF303 5 100 3-4 2.0 : 1 15 15 3.0

SRF303D 12 850412/432 4-6 2.5412D/432D
:1 10 10
412DD/432DD 4.0 412T/43
412/432 412/432 412D/432D 412D/432D 412DD/432DD 412DD/432DD 412T/432T 412T/432T
412H/432H 412DV/432DV 412DDV 712TN/7
e

412H/432H 412H/432H 412DV/432DV 412DV/432DV412DDV 412DDV 712TN/732TN 712TN/732TN

412K For 712D/732D
RF300DD & RF303DD values please see Datasheet
412K 412K 712D/732D 712D/732D
lin

412V
412V 412V
712/732
712/732 712/732
on

9 1 10
9 1 9 1 10
9 1 9 2 1 9 10 1 9
9 8 1 1
8 2 8 2 2
8
9 1 2 9 9 2 9 1
8 7 2 8 3 2
8 1 1
2
8
3 87 23 8 8 2 8
7 3 7 6 3 7 4 3 7 3 7
7 6 43 7 3 3 7 3
6 4 6 4
4 6 4 7 67 4 6
6 6 4 6 4
6 4 6 4

300 SCHEMATIC 300D SCHEMATIC SCHEMATIC

300DD SCHEM
SCHEMATIC SCHEMATIC SCHEMATIC
(Bottom View) SCHEMATIC SCHEMATIC
(Bottom View) SCHEMATIC SCHEMATIC
(Bottom View)
SCHEMATIC (Bottom V
303
(Bottom View)
(Bottom View) (Bottom View)
(Bottom View) 303D (Bottom View)
(Bottom View) 303DD
(Bottom View)
(Bottom View)

Schematics as viewed from terminals

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 5

 RF RELAYS

Series RF312 Electromechanical Relays

The RF312 is designed to improve upon the RF300/RF303 relay’s high frequency performance. The RF312 • Excellent Signal integrity up to 12Gbps+
offers monotonic insertion loss over to 8GHz. This improvement in RF insertion loss over the frequency • Hermetically Sealed
range, makes these relays highly suitable for use in attenuator and other RF circuits. • High Resistance to ESD
The GRF312 is designed to improve upon the GRF300/GRF303 relay’s high frequency performance. The • Metal Enclosure for EMI shielding
• High Repeatability
GRF312 TO-5 relay features a unique ground shield that isolates and shields each lead to ensure excellent
• Broader bandwidth
contact-to-contact
411/431 and pole-to-pole isolation. This ground
411D/431D shield provides a ground
411DD/431DD interface that results in
411T/431T • Through-hole or surface-mount
improved high-frequency performance as well as parametric repeatability. configurations
RF

4 1 4 4 9 1
5 1 5 1 2
Relay Type 5 Nominal
8 Coil Typical RF Performance
7 3
  DPDT
3 Non-Latching
2 3 2 Part No.
3 2 Isolation (dB)
Voltage Resistance
6 4 Frequency VSWR Insertion Loss
Coil Type (Vdc) (Ω) (GHz) (max) Pole to Pole Across Contacts (dB) (max)
SCHEMATIC SCHEMATIC SCHEMATIC (min) (min)
(Bottom View)
  312 = Standard Coil (Bottom View) (Bottom View) SCHEMATIC
(Bottom View) DC-2 1.2 : 1 30 20 0.2

m
Mounting 5 50
2-4 1.2 : 1 25 20 0.4
  RF = Thru-hole RF312
4-6 1.3 : 1 25 20 0.6

co
  GRF = Surface-Mount (Stub)
12 390
  SGRF = Surface-Mount (J-Lead) 6-8 1.4 : 1 20 20 0.8
Temperature
412/432 412D/432D 412DD/432DD 412T/432T DC-2 1.4 : 1 40 30 0.3

s.
412H/432H 412DV/432DV 412DDV 5 712TN/732TN
50
  Storage: –65°C
412K to +125°C 712D/732D
2-4 1.4 : 1 40 30 0.5
412V
  Operating: –55°C to +85°C GRF312
nt
712/732 4-6 1.5 : 1 35 30 1.0
12 390
6-8 1.5 : 1 35 30 1.5
ne

9 1 10
9 1
8 2 2
9 1 9 DC-2 1.2 : 1 40 30 0.2
8 1
3
312 8 2 5 8 50 2
7 3
7
7 3 7 3 2-4 1.2 : 1 35 30 0.5
po

6 4 4
6
6 SGRF312
4 6 4
4-6 1.3 : 1 30 25 1.0
12 390
SCHEMATIC
SCHEMATIC SCHEMATIC SCHEMATIC
(Bottom View) (Bottom View) (Bottom View) (Bottom View) 6-8 1.5 : 1 30 25 1.5
m

Schematics as viewed from terminals

e co
lin
on

Page 6 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 RF RELAYS

Series RF311/RF331 Electromechanical Relays

The RF311/RF331 relays are designed to provide improved RF signal repeatability over the frequency range. • Excellent Signal integrity up to 10Gbps
These relays are highly suitable for use in attenuator and other RF circuits. • Hermetically Sealed
The GRF311 offers monotonic insertion loss to 8GHz. This improvement in RF insertion loss over the • High Resistance to ESD
frequency range makes these relays highly suitable for use in attenuator and other RF circuits. The GRF311 • Metal Enclosure for EMI shielding
• High Repeatability
features a unique ground shield that isolates and shields each lead to ensure excellent
• Broader bandwidth
contact-to-contact isolation. This ground shield provides a ground interface that results in improved • Through-hole or surface-mount
high-frequency performance as well as parametric repeatability. configurations

Relay Type Nominal Coil Typical RF Performance

  SPDT Non-Latching Part No. Voltage Resistance Frequency Isolation Across Insertion Loss
VSWR
Contacts (dB)
Coil Type (Vdc) (Ω) (GHz) (max)
(min)
(dB) (max)

  311 = Standard Coil 5 63 DC-2 1.3 : 1 25 0.2

  331 = Sensitive Coil

m
12 500 2-4 1.6 : 1 20 0.4
Mounting RF311
26 2000 4-6 1.6 : 1 20 0.6
  RF = Thru-hole

co
  GRF = Surface-Mount (Stub) 6-8 1.6 : 1 15 0.8
303 RF311/RF331
Temperature GRF342
GRF303 GRF311 5 63 DC-2 1.2 : 1 30 0.3
  Storage: –65°C to +125°C

s.
/SGRF303 COIL B

RF312 12 500 2-4 1.5 : 1 25 0.5

  Operating: –55°C to +85°C GRF311
26 2000 4-6 1.5 : 1 25 0.7
nt
– 10
9+ 1
8 2
6-8 1.6 : 1 20 1.0
ne

1
4 5 1
7 3 5 125 DC-2 1.3 : 1 25 0.2
2 311 6 +4
3
2 331 5 – 12 1025 2-4 1.6 : 1 20 0.4
3
4 RF331
po

26 4000 4-6 1.6 : 1 20 0.6

MATIC SCHEMATIC COIL A
6-8 1.6 : 1 15 0.8
View) (Bottom View)

SCHEMATIC
m

(Coil A Last Energized)

(Bottom View)

Series GRF342 Electromechanical Relays

The Series GRF342 relay is a hermetically sealed, RF relay designed from inception for surface mount
co

• Excellent Signal integrity up to 10Gbps

applications. This magnetic-latching relay features extremely low internal circuit losses for exceptional • Hermetically Sealed
time and frequency domain response characteristics through and beyond the UHF spectrum and into the S • High Resistance to ESD
band. The GRF342 features a unique ground shield that isolates and shields each lead to ensure excellent • Metal Enclosure for EMI shielding
e

1/GRF341 RF310/RF313 RF320/RF323 • High Repeatability

contact-to-contact and pole-to-pole isolation. This ground shield provides an RF ground interface that
• Broader bandwidth
lin

results in improved high-frequency performance as well as parametric repeatability. The GRF342 extends • Through-hole or surface-mount
performance advantages over similar RF devices that simply offer formed leads for surface mounting. configurations
on

COIL B
1 9 1 9 1
2 _ 8 Relay2Type 8 2
Nominal Coil Typical RF Performance
  DPDT7 Magnetic-Latching
3
Part No. Isolation (dB)
Voltage Resistance Frequency VSWR Insertion Loss
4
+ 6 4
(Vdc) (Ω) (GHz) Pole to Pole Across Contacts (dB) (max)
Coil Type (max)
(min) (min)

CHEMATIC
  342 = SCHEMATIC
Standard Coil SCHEMATIC
A Last Energized)
(Bottom View) (Bottom View) 5 50 DC-2 1.1 : 1 40 35 0.3
Bottom View) Mounting
  GRF = Surface-Mount (Stub) GRF342 12 390 2-4 1.2 : 1 30 30 0.4
RF300/RF303 RF311/RF331 GRF342
GRF300/GRF303 GRF311
Temperature SGRF300/SGRF303 4-6 1.4 : 1 COIL B 25 25 0.8
RF300/RF303 RF311/RF331 GRF342
  Storage: –65°C to +125°C RF312/GRF312
GRF300/GRF303 GRF311
  Operating: –55°C to +85°C SGRF300/SGRF303 COIL B

RF312/GRF312 – 10
9+ 1
8 2
– 10
9 1 9+ 1 7 3
4 5 1
8 2 8 2 6 +4
Schematics as viewed from terminals 7 3
GRF342
5 –
9 1 3 7 2 3
6 44 5 1
8 2 6 +4
7 3 5 –
3 2
6 4 SCHEMATIC SCHEMATIC COIL A
(Bottom View) (Bottom View)

SCHEMATIC
SCHEMATIC SCHEMATIC COIL A (Coil A Last Energized)
(Bottom View) (Bottom View) (Bottom View)

SCHEMATIC
(Coil A Last Energized)
© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT (Bottom
NOTICE View) Page 7
 RF RELAYS

Series RF180 Electromechanical Relays

The Series RF180 relay is a hermetically sealed, magnetic-latching relay featuring extremely low intercontact • Excellent Signal integrity up to 10Gbps
capacitance for exceptional RF performance over the full UHF spectrum. Its low profile height and .100” • Hermetically Sealed
(2.54 mm) grid spaced terminals make it ideal for applications where extreme packaging density and/or close • High Resistance to ESD
PC board spacing are required. • Metal Enclosure for EMI shielding
The GRF180 features a unique ground shield that isolates and shields each lead to ensure excellent contact- • High Repeatability
to-contact and pole-to-pole isolation. This ground shield provides a ground interface that results in improved • Broader bandwidth
high-frequency performance as well as parametric repeatability. • Through-hole or surface-mount
configurations
RF

Relay Type Nominal Coil Typical RF Performance

  DPDT Magnetic-Latching Part No. Isolation (dB)
Voltage Resistance Frequency VSWR Insertion Loss
Coil Type (Vdc) (Ω) (GHz) (max) Pole to Pole Across Contacts (dB) (max)
(min) (min)
  180 = Standard Coil
5 61 DC-2 1.3 : 1 50 30 0.2
Mounting

m
  RF = Thru-hole RF180 12 500 2-4 1.3 : 1 45 30 0.3
  GRF = Surface-Mount (Stub)

co
Temperature 26 2000 4-6 2.0 : 1 30 25 1.5

  Storage: –65°C to +125°C RF180/GRF180

RF100/RF103 5 61 DC-2 1.2 : 1 50 35 0.2

s.
GRF100/GRF103
  Operating: –55°C to +85°C
COIL B
SGRF100/SGRF103 RF180/GRF180
172 COIL B GRF180 12 500 2-4 1.3 : 1 35 30 0.4
nt
10 –
9 1
26 2000 4-6 2.0 : 1 25 30 1.5
10 – 8
9 1 2
+
ne

7 1 8 3
2 7
8
+
+
6 2
3 1806 4
7 + –
5
5 4 3 4
po

6
–
5

COIL A
SCHEMATIC SCHEMATIC
(Bottom View)
COIL A (Coil B Last Energized)
(Bottom View)
SCHEMATIC
m

(Coil B Last Energized)

Series RF341 Electromechanical Relays
(Bottom View)

The RF341 series relay is an ultraminiature, hermetically sealed, magnetic-latching relay featuring extremely • Excellent Signal integrity up to 10Gbps
co

low intercontact capacitance for exceptional RF performance

RF300/RF303 well into the C band. Its low
RF311/RF331 profile and small
GRF342 • Hermetically Sealed
GRF172D size make it ideal for applications where extreme packagingGRF311
GRF300/GRF303
A150/GA150 density and/or close PC board spacing are • High Resistance to ESD
S172D required. Due
RF300/RF303to its minimal mass, many relays may be used toGRF342
RF311/RF331
SGRF300/SGRF303
A152/GA152 configure replacements COIL B for bulkier switching
• Metal Enclosure for EMI shielding
solutions A150/GA150 savings
at substantial
GRF300/GRF303 GRF311
in weight. The
RF312/GRF312 RF341 design has been optimized by increasing the distance
e

A152/GA152 • High Repeatability

SGRF300/SGRF303
between COIL B
the set/reset contacts. This design improvement makes these unique relays the perfect choice for
RF312/GRF312 3 5
• Broader bandwidth
lin

use in RF attenuators, RF switching matrices and other RF applications requiring high isolation,– 10 low insertion • Through-hole or surface-mount
9+ 1
loss and low3VSWR. 5 configurations
8 2 6 – 10 8 2
7 The
1 GRF341 features a unique ground shield that isolates and 9+ shields 1
each lead to ensure excellent contact-
6 to-contact
2
isolation.
2 This
6 ground9 shield 1provides a ground interface
84 5 that
1 2 results in improved high-frequency
7 Attenuator Pad
3
on

8 1 27
performance as well as parametric repeatability. 6 +4
5 9 1Attenuator Pad 7 3 5 –
4 3
1 7
7 4 5 3 1 3 2
8 2 6 4 6 +4
7 3 5 –
SCHEMATIC Relay Type 3 2 Nominal Coil Typical RF Performance
(Bottom View) 6 4
SCHEMATIC
SCHEMATIC SCHEMATIC COIL A
  SPDT Magnetic-Latching Part No. Resistance Frequency Isolation Across
(Bottom View)
(Bottom View) Voltage
(Bottom View)
VSWR Insertion Loss
SCHEMATIC
SCHEMATIC SCHEMATIC (Vdc)
COIL A
(Ω) (CoilSCHEMATIC (GHz) (max) Contacts (dB) (dB) (max)
(Bottom View) Coil Type
(Bottom View) (Bottom View) A Last Energized) (min)
(Bottom View)
SCHEMATIC
  341 = Standard Coil (Coil A Last Energized) 5 61 DC-2 1.2 : 1 30 0.5
(Bottom View)
Mounting 12 500 2-4 1.2 : 1 25 0.8
  RF = Thru-hole RF341
26 2000 4-6 1.4 : 1 20 2.0
  GRF = Surface-Mount (Stub)
Temperature RF341/GRF341 RF310/RF313 RF320/RF323
  Storage: –65°C to +125°C 5 61 DC-2 1.2 : 1 35 0.3
RF341/GRF341 RF310/RF313 RF320/RF323
  Operating: –55°C to +85°C 12 500 2-4 1.3 : 1 30 0.7
+ COIL B
GRF341
9 1 9 26
1 2000 9 1 4-6 1.4 : 1 25 1.5
+ _ 8 2 _ 8 2 8 2
COIL B
9 1 9 1 79 1 3
_ 8 2 _ 7
8 2 8 2
341
COIL A
6
7
4
+3 6 4
7 Schematics as viewed from terminals
COIL A
6 4
+ 6
SCHEMATIC
4
SCHEMATIC SCHEMATIC
(Bottom View) (Bottom View)
(Coil A Last Energized)
(Bottom View)
SCHEMATIC SCHEMATIC SCHEMATIC
Page 8 (Coil A Last Energized) (800) 284-7007
(Bottom View)
• www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com
(Bottom View) © 2010 TELEDYNE RELAYS
(Bottom View)
 RF RELAYS

Series RF310/RF313 Electromechanical Relays

3 RF311/RF331 GRF342
The GRF311
ultraminiature RF310 and RF313 relays are designed with an internal bypass (through path), when the coil is de-energized, to provide low insertion
F303
GRF303 loss and VSWR through the bypass and simplicity of design for the user. Relays have improved RF insertion loss repeatability over the frequency range
COIL B

312
from DC to 3 GHz. Highly suitable for use in attenuator, linear amplifier and other RF circuits.
– 10
• N.C. bypass configuration 9+ 1 • Metal Enclosure for EMI shielding
  • Repeatable insertion loss8 2 • Ground pin option to improve ground case RF grounding
1   • 4Broad Bandwidth
1
7 3 • High isolation between control and signal path
5
2 6 +4
3 5 –
3 2
4 Relay Type Nominal Coil Typical RF Performance
  Normally Closed Bypass Insertion Loss
Part No. VSWR Isolation (dB)
TIC SCHEMATIC COIL A
Voltage Resistance Frequency (dB)
w)
Coil Type
(Bottom View)
(Vdc) (Ω) (GHz)
SCHEMATIC N.O. Bypass N.O. Bypass N.O. Bypass
  310 = Standard Coil (Coil A Last Energized)
(Bottom View)
(max) (max) (min) (min) (max) (max)

  313 = Sensitive Coil 5 50 DC-1 1.2 : 1 1.3 : 1 35 25 0.2 0.3

m
Mounting
RF310 12 390 1-2 1.2 : 1 1.3 : 1 25 25 0.3 0.4
  RF = Thru-hole

co
Temperature 2-3 1.4 : 1 1.3 : 1 25 20 0.4 0.5
GRF341 RF310/RF313
  Storage: –65°C to +125°C RF320/RF323
5 100 DC-1 1.2 : 1 1.3 : 1 35 25 0.2 0.3

s.
  Operating: –55°C to +85°C
RF313 12 850 1-2 1.2 : 1 1.3 : 1 25 25 0.3 0.4
nt
COIL B
1 9 1 9 1 2-3 1.5 : 1 1.3 : 1 25 20 0.5 0.4
2 _ 8 2 RF310 8 2
ne

7 3 RF313
4
+ 6 4
po

EMATIC SCHEMATIC SCHEMATIC

(Bottom View) (Bottom View)
ast Energized)
tom View)
m

Series RF320/RF323 Electromechanical Relays

1/RF331 GRF342
11
The ultraminiature RF320 and RF323 relays are designed with an internal bypass (through path), when the coil is energized, to provide low insertion loss
co

and COIL
VSWR B
through the bypass and simplicity of design for the user. The RF320 and RF323 relays have improved RF insertion loss repeatability over the
frequency range from DC to 3 GHz. Highly suitable for use in attenuator, linear amplifier and other RF circuits.
– 10
• N.O.
9+ bypass
1 configuration
e

• Metal Enclosure for EMI shielding

  • 8Repeatable insertion
2 loss • Ground pin option to improve ground case RF grounding
lin

1
  • 7Broad Bandwidth
3 • High isolation between control and signal path
5
6 +4
5 –
2
Relay Type Nominal Coil Typical RF Performance
on

  Normally Open Bypass Insertion Loss

Part No. VSWR Isolation (dB)
HEMATIC COIL A
Voltage Resistance Frequency (dB)
ttom View)
Coil Type (Vdc) (Ω) (GHz)
SCHEMATIC N.C. Bypass N.C. Bypass N.C. Bypass
  320(Coil= AStandard
Last Energized) Coil (max) (max) (min) (min) (max) (max)
(Bottom View)
  323 = Sensitive Coil 5 50 DC-1 1.2 : 1 1.4 : 1 30 25 0.2 0.4
Mounting
RF320 12 390 1-2 1.2 : 1 1.4 : 1 30 20 0.3 0.4
  RF = Thru-hole
Temperature 2-3 1.4 : 1 1.4 : 1 25 20 0.4 0.6
10/RF313   Storage: –65°C
RF320/RF323 to +125°C
5 100 DC-1 1.2 : 1 1.4 : 1 30 25 0.2 0.4
  Operating: –55°C to +85°C
RF323 12 850 1-2 1.2 : 1 1.4 : 1 30 20 0.3 0.4

1 9 1
2-3 1.4 : 1 1.4 : 1 25 20 0.4 0.5
2 8 2 RF320
3 RF323
6 4

CHEMATIC SCHEMATIC
Bottom View) (Bottom View)
Schematics as viewed from terminals

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 9

 RF RELAYS

Series A150 Electromechanical Relays

The Series A150 ultraminiature Attenuator Relays are designed for attenuating RF signals in 50-ohm • Excellent phase linearity
systems over a frequency range from DC to 3 GHz. Their low profile and small grid spacing makes • Hermetically Sealed
them ideal for use when packaging density is a prime consideration. The A150 relays eliminate the • High Resistance to ESD
need for additional external resistors. • Metal Enclosure for EMI shielding
These single section, switchable attenuator relays have internal matched thin film attenuator pads in • High Repeatability
RF180/GRF180
“L,” “T” or “Pi” configurations, as applicable. Relays are available in fixed increments of 1, 2, 3, 4, 5, • Broader bandwidth
6,COIL
8,RF180/GRF180
B10, 16 and 20 dB, which can be used singly or in combination to achieve the attenuation levels
• Through-hole or surface-mount configurations
desired.
COIL B
The GA150 features a unique ground shield that isolates and shields each lead to ensure excellent
RF

10 –
contact-to-contact
9 1 isolation. This ground shield provides a ground interface that results in improved
high-frequency
8
9
10 – performance as well as parametric repeatability.
1 2
+
8 3
2
+7
+

6
7
Relay
3 Type
4
+
Nominal Coil Typical RF Performance
–
5
  RF6 Attenuator 4 VSWR Insertion Loss
5
– Part No. Voltage Resistance Frequency (dB)
Coil Type (Vdc) (Ω) (GHz)

m
COIL A Attenuated Thru Path
SCHEMATIC Typ. Max.
Path (Typ.) (Max.)
  A150
(Coil B=
LastStandard
Energized) COIL Coil
A

SCHEMATIC
(Bottom View)
Mounting 5 50 DC-1 1.20 : 1 1.10 : 1 0.1 0.25

co
(Coil B Last Energized)
(Bottom View)

  A = Thru-hole
  GA = Surface-Mount (Stub) 12 390 1-2 1.30 : 1 1.20 : 1 0.2 0.35
A150

s.
Temperature
A150/GA150 15 610 2-3 1.40 : 1 1.25 : 1 0.3 0.55
A152/GA152
  Storage: –65°C to +125°C
A150/GA150
nt
A152/GA152
  Operating: –55°C to +85°C 26 1560
3 5

3 5 5 50 DC-1 1.20 : 1 1.20 : 1 0.1 0.25

ne

2 6

2 Attenuator Pad 6 12 390 1-2 1.20 : 1 1.20 : 1 0.2 0.35

1 7
Attenuator Pad
150 GA150
po

1 7 15 610 2-3 1.20 : 1 1.30 : 1 0.3 0.45

26 1560
SCHEMATIC
m

(Bottom View)
SCHEMATIC
(Bottom View)
Series A152 Electromechanical Relays
co

The Series A152 highly repeatable ultraminiature attenuator relays are designed for attenuating RF • Hermetically Sealed
signals in 50-ohm systems over a frequency range from DC to 5 GHz. Their low profile and small • High Resistance to ESD
grid spacing makes them ideal for use when packaging density is a prime consideration. The A152 • Metal Enclosure for EMI shielding
relays eliminate the need for additional external resistors/attenuators.
RF180/GRF180
e

• High Repeatability
These single section, switchable attenuator relays have an internal matched thin film attenuator pad
COILRF180/GRF180
B
• Broader bandwidth
in a “Pi” configuration. Relays are available in a fixed increment of 20 dB. (Other values available)
lin

COIL B • Through-hole or surface-mount

The GA152 features a unique ground shield that isolates and shields each lead to ensure excellent configurations
10 –
contact-to-contact
9 1
isolation. This ground shield provides a ground interface that results in improved
high-frequency
9
8
10 – performance as well as parametric repeatability.
on

1
2
+
8 3
2
+7
Relay Type Nominal Coil Typical RF Performance
+

3
4
7
6 +

  RF Attenuator VSWR Insertion Loss

–
5
4
6
5
– Part No. Voltage Resistance Frequency (dB)
Coil Type (Vdc) (Ω) (GHz) Attenuated Thru Path
COIL A
Typ. Max.
SCHEMATIC Path (Typ.) (Max.)
  A152 = Standard
COIL A Coil
(Coil B Last Energized)
SCHEMATIC
(Bottom View)
5 50 DC-1 1.20 : 1 1.10 : 1 0.1 0.25
(Coil B Last Energized) Mounting
(Bottom View)
  A = Thru-hole
12 390 1-2 1.30 : 1 1.20 : 1 0.2 0.35
  GA = Surface-Mount (Stub) A152
Temperature
A150/GA150 15 610 2-3 1.40 : 1 1.25 : 1 0.3 0.55
A152/GA152
  Storage: –65°C to +125°C
A150/GA150
A152/GA152 26 1560 3-5 See Datasheet
  Operating: –55°C to +85°C
3 5
5 50 DC-1 1.20 : 1 1.20 : 1 0.1 0.25
3 5
2 6

2 Attenuator Pad 6 12 390 1-2 1.20 : 1 1.20 : 1 0.2 0.35

1 7
152 GA152
Attenuator Pad
1 7 15 610 2-3 1.20 : 1 1.30 : 1 0.3 0.45

26 1560 3-5 1.40 : 1 1.70 : 1 0.4 0.55

SCHEMATIC
(Bottom View)
SCHEMATIC
Page 10(Bottom View) (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 COMMERCIAL RELAYS

Series 122C Electromechanical Relays

The 122C Centigrid® magnetic-latching relay is an ultraminiature, hermetically sealed, armature relay • All welded construction
capable of being directly driven by most IC logic families. Its low profile height and .100” (2.54 mm) grid • Unique uni-frame design providing high
spaced terminals, which precludes the need for spreader pads, make it ideal for applications where extreme magnetic efficiency and mechanical rigidity
packaging density and/or close PC board spacing are required. • High force/mass ratio for resistance to shock
The basic operating function and internal structure are similar to Teledyne’s TO-5, 422 relay series. The and vibration
122C is capable of meeting Teledyne Relays’ T2R® requirements. • Precious metal alloy contact material with
The Series 122C relay has internal silicon diodes for coil suppression, Zener diodes to protect the MOSFET gold plating assures excellent high current
gate inputs, and N-channel enhancement-mode MOSFET chips, which enable direct relay interfacing with and dry circuit switching capabilities
most microprocessor and IC logic families (CMOS, TTL and MOS).
The 122C magnetic-latching relay is ideally suited for applications where coil operating power must be
minimized. The relays can be operated with a short-duration pulse. After the contacts have transferred, no
external coil power is required.
The magnetic-latching feature of the Series 122C relay provides a “memory” capability, since the relays will
not reset upon removal of coil power.

Relay Type Nominal Coil

m
  DPDT Magnetic-Latching Coil Current
Part No. Operating Latch and Contact Load Rating
Voltage (mA)
CMOS Feature Power (mW) Reset Voltage

co
(Vdc)
Min. Max. (Vdc) (Max)
  Internal power MOSFET
  driver and diode coil 5 82.2 114.9 505 3.5   Resistive: 1A/28Vdc

s.
  suppression 6 41.6 57.0 296 4.5   Inductive: 200mA/28Vdc (320mH)
9 27.4 37.2 288 6.8   Lamp: 100mA/28Vdc
Vibration Shock 122C
nt
12 20.5 27.8 287 9.0   Low Level: 10 to 50 uA/10 to 50 mV
30 g’s 100 g’s 6 msec,
116C, 136C
half-sine 18 13.7 18.2 286 13.5
to 3000 Hz
26 11.4 122C
15.2 351 18.0
ne

Acceleration
– 10
  50 g’s 9 +1
9
10 +
1

Temperature
po

8 2 8 2 PIN 4: GATE A
PIN 1: + SUPPLY
  Storage: –65°C to +125°C
7 3 PIN 9: – SUPPLY
7 3
PIN 5: – SUPPLY
PIN 9: GATE B 122C
PIN 10: GATE PIN 10: + SUPPLY
4
  Operating: –55°C to +85°C 6 6
4
5–
m

SCHEMATIC SCHEMATIC
(Bottom View) (Coil A Last Energized)
(Bottom View)
co

RF100/RF103 RF180/GRF180
Series 172 Electromechanical Relays GRF100/GRF103 COIL B
The 172 Centigrid® relay is an ultraminiature, hermetically sealed, armature relay for commercial SGRF100/SGRF103
172
• All welded construction
e

applications. Its low profile height .280” (7.11 mm) and .100” (2.54 mm) grid spaced terminals, which • Unique uni-frame design providing high
preclude the need for spreader pads, make it an ideal choice where extreme packaging density and/or close magnetic efficiency and mechanical rigidity
9
10 –
lin

1
PC board spacing are required. • High force/mass ratio for resistance to shock
8
The Series 172 relay has an internal discrete silicon diode for coil transient suppression. and vibration +
2

7 1 3
By virtue of its inherently low intercontact capacitance and contact circuit losses, the 172 relay is an • 8Precious metal alloy contact material with
7 +
6 2
excellent subminiature RF switch for frequencies well into the UHF spectrum. Applications include
on

gold plating assures excellent high current

6
4

telecommunications, test instruments, mobile communications, attenuators, and automatic test equipment. 4and3 dry circuit switching capabilities
–
5
5

Relay Type Nominal Coil SCHEMATIC

C

SCHEMATIC
  DPDT Non-Latching Part No. Voltage Resistance P.U.V Operating
(Bottom View)
Contact Load Rating (Coil B Last Energized)
(Bottom View)
(Vdc) (Ω) (Vdc) (max.) Power (mW)
Diode Options
3 39 2.25 235   Resistive: 1A/28Vdc
  D = Internal diode for coil
172 5 64 3.8 405   Inductive: 200mA/28Vdc (320mH)
  transient suppression
172D 12 400 9.0 360
GRF172D
  Lamp: 100mA/28Vdc A150/GA150
Vibration Shock 114, 134
26
S114/S134 1600 18.0 440
S172D  114D,
Low134D
Level: 10 to 50 uA/10 to 50 mV
A152/GA152
30 g’s 6 msec, 172 S114D/S134D
10 g’s to 500 Hz 172D
half-sine 3 5

Temperature
7 1 8 8 2 6
7 17 1
  Storage: –65°C to +125°C 6
8
2
  Operating: –55°C to +85°C 172 6 26
172D
2 1
Attenuator Pad
7
5 4 3 5
4 35
4 3

Schematics as viewed from terminals SCHEMATIC P.U.V = Pick-Up Voltage

SCHEMATIC SCHEMATIC
(Bottom View) (Bottom View)
(Bottom View) SCHEMATIC
(Bottom View)
114DD, 134DD
S114DD/S134DD

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 11

8
7 1

6 2
 COMMERCIAL RELAYS

Series 712 Electromechanical Relays

The TO-5 relay, originally conceived and developed by Teledyne, has become one of the industry standards • All welded construction
for low-level switching from dry circuit to 1 ampere. Designed for high-density PC board mounting, the Series • Unique uni-frame design providing
712 relays are some of the most versatile ultraminiature relays available because of their small size and low high magnetic efficiency and mechanical
coil power dissipation. rigidity
The Series 712D relay has an internal discrete silicon diode for coil transient suppression. The hybrid Series • High force/mass ratio for resistance to shock
712TN relay has an internal silicon diode and transistor driver. The integrated packaging of the relay with its and vibration
associated semiconductor devices greatly reduces PC board floor space requirements as well as component • Precious metal alloy contact material with
installation costs. 411/431 411/431 411D/431D 411D/431D411DD/431DD 411DD/431DD 411T/431T
411/431 411D/431D 411DD/431DD gold plating assures excellent 411T/431T
411T/431T high current
By virtue of its inherently low intercontact capacitance and contact circuit losses, the 712 has proven to be and dry circuit switching capabilities
excellent ultraminiature RF switch for frequency ranges well into the UHF spectrum. A typical RF application
1 1
for the TO-5 relay is in handheld radio transceivers, 4wherein
4 5 1
the combined
4 1 4features of good
1 4 RF performance,
4
5 1 4
9
12 9 1
small size, low coil power dissipation and high reliability make
5
5
it a preferred
4 5
method 1 4
1 of Transmit-Receive
5 5 1
5 1 8 9 2 8
2
5 8
7 3
switching. 3 2 3 2 3 2 7 3 7 3
3 2 3 2 3 2 6 4
3 2 3 2 3 2 6 4
6 4

SCHEMATIC
Relay Type SCHEMATIC
(Bottom View)
SCHEMATICSCHEMATIC
SCHEMATIC
(Bottom Nominal
View) Coil SCHEMATIC
SCHEMATIC SCHEMATIC
(Bottom View)
SCHEMATIC
SCHEMATIC
COMMERCIAL

(Bottom View)
(Bottom View) (Bottom View)
(Bottom View) (Bottom View)
(Bottom View)
SCHEMATIC
(Bottom View)
SCHEMATIC
Base Current

m
  DPDT Non-Latching Part No. Voltage Resistance P.U.V Contact Load Rating
(Bottom View)
(Bottom View)

to Turn On
Diode Options (Vdc) (Ω) (Vdc) (max.)
(712 TN only)

co
  D = Internal diode for coil 5 50 3.6 3.00   Resistive: 1A/28Vdc
  transient suppression 6 98 4.2 2.04   Inductive: 200mA/28Vdc (320mH)
712
  TN = Internal transistor driver 9 220 6.5 1.36   Lamp: 100mA/28Vdc
412/432
712D 412D/432D 412D/432D412DD/432DD 412DD/432DD 412T/432T

s.
  and coil transient suppression 412/432 12 412/432 390
412H/432H 412D/432D 8.4 412DD/432DD
1.03 412T/432T
  Low Level:712TN/732TN
412T/432T
10 to 50 uA/10 to 50 mV
712TN
412H/432H 412H/432H412DV/432DV
412DV/432DV
412DDV
412DV/432DV
412DDV 412DDV 712TN/732TN 712TN/732TN
412K 18 412K 712D/732D
880
  diode 412K
412V 712D/732D 13.0
712D/732D 0.68
nt
Vibration Shock 412V
712/732 26 412V 1560 17.0 0.50
712/732 712/732
421 421 421D421D 421DD
421DD
30 g’s 6 msec,
10 g’s to 500 Hz
ne

half-sine 9 1 10
9 9
1 1 10
9 12 9 1 1 10
Temperature 8
8 8 9
2
12
28
9
9 12 9 1 9
9 1 9
8 2 8 2 8 2 8 1 2 1
2COIL B
7 3 3 COIL COILCOIL
B B 29 8 9 8 COIL B 2
  Storage: –65°C to +125°C 3 79
7 3 COIL B B 3 8 78 9 9
po

76 9 3 7 7 3 3 1 1
4 17 1 1 1 3 3
64 4 7 76 3 7
6 4 8 6 8 4 6 4 76 48 3 8 4
  Operating: –55°C to +85°C 6
6 4 6 4
6
6 4 8 8
2 2
7 74 2 4 2 7 74 2 4 2 4
7 74 4

712
SCHEMATIC
COILCOIL
A A 6 6
SCHEMATICSCHEMATIC 712D
SCHEMATIC SCHEMATIC 6 6
SCHEMATIC COILCOIL
712TN
SCHEMATIC
ASCHEMATIC SCHEMATIC
6 6
SCHEMATIC
(Bottom View) SCHEMATIC
(Bottom View) SCHEMATIC
(Bottom View) AView)
(Bottom
m

(Bottom View) (Bottom View) (Bottom View) (Bottom View)

(Bottom View) (Bottom View) (Bottom View) Schematics as(Bottom
viewedView)
from terminals
Series 722 Electromechanical Relays SCHEMATIC
SCHEMATIC
(Coil A(Coil
Last A
Energized)
Last Energized)
SCHEMATIC
SCHEMATIC
(Coil A(Coil
Last A
Energized)
Last Energized) SCHEMATIC
SCHEMATIC
co

The magnetic-latching TO-5 relay, originally conceived and developed (Bottomby Teledyne,
View)
(Bottom View) has become one of the (Bottom View) View)
(Bottom
• All welded construction
(Coil A(Coil
Last A
(Bottom
Energized)
Last Energized)
View) View)
(Bottom
industry standards for low-level switching from dry circuit to 1 ampere. Designed for high-density PC board • Unique uni-frame design providing
mounting, the 722 relay has become one of the most versatile ultraminiature relays available because of its high magnetic efficiency and mechanical
small size and low coil power dissipation. rigidity
e

The Series 722D relay has discrete silicon diodes for coil transient suppression.
420 420 •420D
High420Dforce/mass ratio for resistance to shock 420DD 420DD
The Series 722 magnetic-latching relays are ideally suited for applications where coil power dissipation
lin

and vibration
must be minimized. The relays can be operated with a short duration pulse and after the contacts have • Precious metal alloy contact material with
transferred, no external coil power is required. The magnetic-latching
COIL COIL
B B 9
feature
9
of the Series 722 provides aB B 9 gold
COIL COIL 9 plating assures excellent high current
COIL COIL
B B 9 9
1 1 1 1 1 1
“memory” capability, since the relays will not reset upon removal of coil power. 8 8
and dry circuit switching capabilities 8 8
on

2 8 8 2 2 2 2 2
7 7 3 3 7 7 3 3 7 7 3 3
6 6 6 6 6 6
5 45 4 5 45 4 5 45 4
Relay Type Nominal Coil
COIL COIL
A A COIL ACOIL A COI
  DPDT Magnetic-Latching Part No. Voltage Resistance Set & Reset Contact Load Rating
SCHEMATIC
SCHEMATIC SCHEMATIC
SCHEMATIC
(Vdc)
(Coil A(Coil
Last A
Energized) (Ω)
Last Energized) Voltage (Vdc) (Coil A(Coil
Last A
Energized)
Last Energized) SCHEMATIC
SCHEMATIC
Diode Options (Bottom View) View)
(Bottom (Bottom View) View)
(Bottom (Coil A(Coil
Last A
Energized)
Last Energize
5 61 3.5   Resistive: 1A/28Vdc (Bottom View) View)
(Bottom
  D = Internal diode for coil
6 120 4.5   Inductive: 200mA/28Vdc (320mH)
  transient suppression
722 9 280 6.8   Lamp: 100mA/28Vdc
Vibration Shock 722D 12 500 9.0   Low Level: 10 to 50 uA/10 to 50 mV
422D422D 422DD
422DD
30 g’s 6 msec, 18422 422 1130 13.5
10 g’s to 500 Hz 422H422H
half-sine 26422K422K 2000 18.0
Temperature 722 722
COIL COIL
B B COIL COIL
B B COIL COIL
B B
  Storage: –65°C to +125°C 10 10 10 10 10 10
9 9 1 9 9 1 1 9 9 1 1
1
  Operating: –55°C to +85°C 8 2 2 2 2
8 8 2 2 8 8 8
722 3 3
722D 3 3
7 7 3 3 7 7 7 7
6 6 6 6 6 6
4 4 4 4 4 4
5 5 5 5 5 5

COIL COIL
A A COIL COIL
A A

SCHEMATIC
SCHEMATIC SCHEMATIC
SCHEMATIC
(Coil A(Coil
Last A
Energized)
Last Energized) (Coil A(Coil
Last A
Energized)
Last Energized) SCHEMATIC
SCHEMATIC
(Bottom View) View)
(Bottom (Bottom View) View)
(Bottom (Coil A(Coil
Last A
Energized)
Last Energized
(Bottom View) View)
(Bottom

Page 12 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 COMMERCIAL RELAYS

Series 732 Electromechanical Relays

The TO-5 relay, originally conceived and developed by Teledyne, has become one of the industry standards • All welded construction
for low-level switching from dry circuit to 1 ampere. Designed for high-density PC board mounting, the Series • Unique uni-frame design providing high
732 relay is one of the most versatile ultraminiature relays available because of their small size and low coil magnetic efficiency and mechanical rigidity
power dissipation. The sensitive 732 relay has a high resistance coil, thus requiring extremely low operating • High force/mass ratio for resistance to shock
power (200 mW typical). The advantages of reduced heat dissipation and power supply demands are a plus. and vibration
The Series 732D relay has an internal discrete silicon diode for coil transient suppression. The hybrid Series • Precious metal alloy contact material with
732TN relay has an internal silicon diode and transistor driver. The integrated packaging of the relay with its gold plating assures excellent high current
associated semiconductor devices greatly reduces PC board floor space requirements as well as component and dry circuit switching capabilities
installation costs.
By virtue of its inherently low intercontact capacitance and contact circuit losses, the 732 has proven to be
excellent ultraminiature RF switch for frequency ranges well into the UHF spectrum. A typical RF application
for the TO-5 relay is in handheld radio transceivers, wherein the combined features of good RF performance,
small size, low coil power dissipation and high reliability make it a preferred method of Transmit-Receive
switching.
411/431 411D/431D
411/431 411DD/431DD 411T/431T
411/431 411D/431D 411D/431D 411DD/431DD 411DD/431DD 411T/431T 411T/431T

Relay Type Nominal Coil

m
4 1 4 1 4 9 1 1
4 4 5 4 9
54 1 54 1 4 1 5 9 2 1
  DPDT Non-Latching Coil 5
1 5 1 5 81 2
Part No. 5
Voltage Resistance
5 Base1 Current 8 Contact2 8
Load Rating
P.U.V 7 3 3 7
2to Turn On

co
Diode Options 3
3
2
2
3
3 (Vdc) 2 2
(Ω) 2 3 3 2
(Vdc) (max.) 3 26 7
4
3
6
3 3 (712 TN
2 only) 4
6 4
  D = Internal diode for coil
SCHEMATIC SCHEMATIC
  transient suppression (BottomSCHEMATIC
View) 5 SCHEMATIC
SCHEMATIC
View) 100
(BottomSCHEMATIC
SCHEMATIC
3.5 (BottomSCHEMATIC
View) 1.50 SCHEMATICSCHEMATIC   Resistive: 1A/28Vdc
(Bottom View) (Bottom View) (Bottom View) SCHEMATIC

s.
(Bottom View) (Bottom View) (Bottom View) (BottomSCHEMATIC
View)
  TN = Internal transistor driver 6 200 4.5 1.00   Inductive:
(Bottom200mA/28Vdc
(Bottom View)
View) (320mH)
732
  and coil transient suppression 9 400 6.8 0.75   Lamp: 100mA/28Vdc
732D
nt
  diode 12 850 9.0 0.47   Low Level: 10 to 50 uA/10 to 50 mV
732TN
18 1600 13.5 0.38
Vibration Shock
26 3300 18.0 0.24
ne

30 g’s 6 msec,
10 g’s to 500 Hz 412/432 412D/432D
412/432 412DD/432DD 412T/432T
half-sine 412/432
412H/432H 412D/432D
412DV/432DV
412D/432D 412DD/432DD 412DD/432DD
412DDV 412T/432T 412T/432T
412H/432H 412DV/432DV 412DDV 712TN/732TN 712TN/732TN
412K 412H/432H 412DV/432DV
412K 712D/732D 712D/732D
412DDV 712TN/732TN
Temperature 712D/732D
412V 412K
po

412V 412V
  Storage: –65°C to +125°C 712/732 712/732
712/732
  Operating: –55°C to +85°C
m

9 1 10 10
9 9 1 1 1
9 1 9 9 1 9 10
8 2 8 8 92 2 1 9 1 9
8 2 8 8 2 9 2 1
82 91 21 1
8 2 2
7 3 3 2 8 2 8
co

7 7 3 3 8 8
7 3 7 7 3 7 3 3
6 4 74 4 3 7 3 7
6 6 6 46 7 3 7 3
6 4 4 4 4 6 4
6 6 6 4
6 4 6 4

SCHEMATIC 732 SCHEMATIC

SCHEMATIC 732D SCHEMATIC
SCHEMATIC 732TN
SCHEMATIC SCHEMATIC SCHEMATIC
e

(BottomSCHEMATIC
View) (BottomSCHEMATIC
View) (BottomSCHEMATIC
View) (BottomSCHEMATIC
View)
(Bottom View) (Bottom View) (Bottom View) (Bottom View)
(Bottom View) (Bottom View) (Bottom View) (Bottom View)

Schematics as viewed from terminals

lin
on

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 13

 COMMERCIAL surface-mount RELAYS

Series S114 & S134 Electromechanical Relays

The Series S114 Surface Mount Centigrid® Relay is an ultraminiature, hermetically sealed, armature relay. The low profile height .360” (9.14 mm) and .100”
(2.54 mm) lead spacing make it ideal for applications where extreme packaging density and/or close PC board spacing are required. The specially formed
leads are pre-tinned to make the relays ideal for most types of surface mount solder reflow processes.
The basic design and internal construction are identical to the Series 114 & 134 Centigrid® relays, and are capable of meeting Teledyne Relays’ T2R®
requirements.
The S114D and S114DD relays have internal discrete silicon diodes for coil suppression and polarity reversal protection.
The sensitive S134 surface mount Centigrid® Relay has a high resistance coil, thus requiring extremely low operating power (200 mW typical). The
advantages of reduced heat dissipation and power supply demands are a plus.

  • All welded construction • High force/mass ratio for resistance to shock and vibration
  • Unique uni-frame design providing • Precious metal alloy contact material with gold plating assures excellent high
  high magnetic efficiency and mechanical rigidity current and dry circuit switching capabilities

Relay Type Nominal Coil

  DPDT Non-Latching Part No. Voltage Resistance P.U.V D.O.V (Vdc) Contact Load Rating

m
Coil Type (Vdc) (Ω) (Vdc) (max.) min. max.

  S114 = Standard Coil 5 50 3.5 0.14 2.3   Resistive: 1A/28Vdc

co
  S134 = Sensitive Coil 6 98 4.5 0.18 3.2   Inductive: 200mA/28Vdc (320mH)
CO M M ERC IAL SUR FACE - M OU N T

Diode Options S114 9 220 6.8 0.35 4.9   Lamp: 100mA/28Vdc

S114D 12 390 9.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV

s.
  D = Internal diode for coil
  transient suppression 18 880 13.5 0.59 10.0
26 1560 18.0 0.89 13.0
nt
  DD = Internal diode for coil
  transient suppression and 5 39 4.0 0.6 2.8   Resistive: 1A/28Vdc

  polarity reversal protection 6 78 5.0 0.7 3.4   Inductive: 200mA/28Vdc (320mH)

ne

9 220 7.8 0.8 5.3   Lamp: 100mA/28Vdc

Vibration Shock S114DD
12 390 10.0 0.9 6.5   Low Level: 10 to 50 uA/10 to 50 mV
30 g’s to 3000 75 g’s 6 msec,
18 880 14.5 1.1 10.0
po

Hz half-sine
26 1560 19.0 1.4 13.0
Acceleration
5 100 3.5 0.12 2.5   Resistive: 1A/28Vdc
  50 g’s 6 200 4.5 0.18 3.2   Inductive: 200mA/28Vdc (320mH)
m

Temperature S134 9 400 6.8 0.35 4.9   Lamp: 100mA/28Vdc

  Storage: –65°C to +125°C S134D 12 800 9.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV
co

  Operating: –55°C to +85°C 18 1600 13.5 114,0.59

134 10.0
S114/S134 114D, 134D
26 3200 18.0 172
0.89 13.0 S114D/S134D
172D
5 64 3.7 0.7 2.6   Resistive: 1A/28Vdc
e

6 125 4.8 0.8 3.0   Inductive: 200mA/28Vdc (320mH)

lin

7 1 8
9 400 8.0 0.9
8
4.5   Lamp: 100mA/28Vdc7 1
S134DD 6 2
12 800 11.0 1.0 5.8   Low Level: 10 to 50 uA/10 to6 50 mV 2
4
18 1600 14.5 5 1.1 3 9.0 5
on

4 3
26 3200 19.0 1.3 13.0
SCHEMATIC SCHEMATIC
114, 134 114, 134 (Bottom View) (Bottom View)
S114/S134 S114/S134 114D, 134D 114D, 134D
172 172 S114D/S134D S114D/S134D 114DD, 134DD
172D 172D S114DD/S134DD

7 1 7 1 8 8 8
7 1 7 7 1
8 8 1
6 2 6 2
6 2 6 6 2
2
5 4 3
5 4 3 5 5
4 3 5 3
3 4
4

SCHEMATIC SCHEMATIC SCHEMATIC

SCHEMATIC SCHEMATIC
(Bottom View)
S114
(Bottom View) S114D
(Bottom View)
(Bottom View)
S114DD
(Bottom View)

S134 114DD, 134DD S134D S134DD

S114DD/S134DD 114DD, 134DD
S114DD/S134DD 116C, 136C
122C
8
7 1
8 – 10
7 1 9 +1
9
10 +
1
6 2
6 2
5 8 2 8 2
3 PIN 4: GATE A
4 PIN 1: + SUPPLY PIN 5: – SUPPLY
5 3 PIN 9: – SUPPLY
4 7 3 PIN 9: GATE B
Schematics as viewed from terminals PIN 10: GATE
7 3
PIN 10: + SUPPLY
SCHEMATIC 6
4
6
4
(Bottom View)
SCHEMATIC 5–
(Bottom View)
SCHEMATIC SCHEMATIC
Page 14 (800)
116C,284-7007
136C • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com
(Bottom View) © 2010 TELEDYNE RELAYS
(Coil A Last Energized)
(Bottom View)
116C, 136C 122C
122C
 COMMERCIAL surface-mount RELAYS

Series S172 Electromechanical Relays

The S172 surface mount Centigrid® relay is an ultraminiature, hermetically sealed, armature relay for • All welded construction
commercial applications. Its low profile height .470” (11.94 mm) and .100” (2.54 mm) grid spaced terminals • Unique uni-frame design providing high
make it an ideal choice where extreme packaging density and/or close PC board spacing are required. The magnetic efficiency and mechanical rigidity
specially formed surface-mount leads are pre-tinned to make the relays ideal for all types of surface-mount • High force/mass ratio for resistance to shock
solder reflow processes. and vibration
The basic design and internal structure are similar to Teledyne’s DPDT 114 Centigrid® relay. (see page 16) • Precious metal alloy contact material with
The S172D relay has an internal discrete silicon diode for coil transient suppression. gold plating assures excellent high current
and dry circuit switching capabilities

Relay Type Nominal Coil

  DPDT Non-Latching Part No. Voltage Resistance P.U.V Operating Contact Load Rating
(Vdc) (Ω) (Vdc) (max.) Power (mW)
Diode Options
5 64 3.8 405   Resistive: 1A/28Vdc
  D = Internal diode for coil
S172 12 400 9.0 360   Inductive: 200mA/28Vdc (320mH)
  transient suppression

m
S172D 26
114,114,
134134 1600 18.0 440114D, 134D   Lamp: 100mA/28Vdc
S114/S134 114D, 134D
Vibration Shock S114/S134
  Low
S114D/S134D
S114D/S134D Level: 10 to 50 uA/10 to 50 mV
172172
172D
172D
30 g’s 6 msec,

co
10 g’s to 500 Hz
half-sine 7 1 8
7 1 7 78 1
8 1
6 8
Temperature 6 2 2
6 2
6 2

s.
4
  Storage: –65°C to +125°C 5 54 3 3
5 5
43 3
4
  Operating: –55°C to +85°C
SCHEMATIC
SCHEMATIC SCHEMATIC
421 S172 421D S172D
SCHEMATIC 421DD
(Bottom
View)View)
nt
421 421 (Bottom
421D
421D (Bottom
(Bottom View)View) 421DD
421DD
114DD,
114DD, 134DD
134DD
S114DD/S134DD
S114DD/S134DD
Series S422 Electromechanical Relays
ne

The magnetic-latching TO-5 relay, originally conceived and developedCOILby Teledyne,

B has
7 7 become
8 8
1 one of the • COIL B
AllCOIL
welded
9 COIL B B B 9 9 91 1
COILCOIL B construction
COIL B 9
industry standards for low-level switching from 9 9dry1
1
circuit
1 1 COIL
toCOIL B B
ampere. Designed for high-density
6 6 21 2 1
PC board • Unique uni-frame
9 91
design providing1 1 high
8 8 8
surface mounting, its small size and low coil 87 power 2 dissipation make the S422 relay one 87 58of the most versatile magnetic efficiency and 2
4 mechanical rigidity
2 8
po

8 8
4 7 2 2 5 4 74 3 2 3 2 7 2 2
ultraminiature relays available. 7 4 4 7 4 4 4
• High force/mass
7 74 4
COIL A 6 6 6 ratio for resistance to shock
The Series S422D and S422DD COILutilize
A A discrete
COIL 6 6 diodes for coil suppression and polarity 6 reversal
SCHEMATIC protection.
6 COIL A 6 6 COIL A
SCHEMATIC A A and vibration
COILCOIL COILCOIL
A A
The Series S422 magnetic-latching relays are ideally suited for applications where power dissipation
(Bottom
(Bottom View)View) must be • Precious metal alloy contact material with
minimized. The relays can be operated SCHEMATIC
with a short duration pulse. After the contacts have transferred, no
m

SCHEMATIC gold plating assures excellent high current

external holding power is required. (Coil A Last SCHEMATIC
SCHEMATIC
Energized)
116C, 136C (Coil A Last SCHEMATIC
SCHEMATIC
Energized) SCHEMATIC
(Coil A(Coil
(Bottom Last A Last Energized)
Energized)
View) 116C, 136C (Coil A(Coil
(Bottom Last A Last Energized)
Energized)
View) and dry circuit
(Coilswitching
A Last SCHEMATIC
SCHEMATIC
Energized) capabilities
The magnetic-latching feature of the Series (Bottom S422 relays
(Bottom
View) View) provide a “memory” capability,(Bottom since (Bottom
View)the
View)relays will122C
122C (Coil A(Coil
(Bottom Last A Last Energized)
Energized)
View)
(Bottom (Bottom
View) View)
co

not reset upon removal of coil power.

– 9 – 10 10
+1 +1 10 + 10 +
9 9 9 1 1

8 8 2 2 8 2
8 2 PIN 4:PIN 4: GATE
GATE A A
Relay Type 420 Nominal
PIN 1:PIN 1: + SUPPLY 420D
9: – SUPPLY Coil 420D
+ SUPPLY PIN 5:PIN 5: – SUPPLY
– SUPPLY 420DD
420 420 3PIN 9:PIN 420D 420DD
420DD
e

7 7 3 – SUPPLY 7 PIN 9:PIN

3 9: GATE
GATE B B
PINGATE
10: GATE 7 3 PIN+ 10: + SUPPLY
PIN 10:

  DPDT Magnetic-Latching Part No. Voltage Resistance

6 6
4
Set & Reset
4
6 6 4 4 Contact Load Rating
PIN 10: SUPPLY

(Ω)
5–
lin

(Vdc) Voltage (Vdc) 5–

Diode Options COIL B 9

91
SCHEMATIC COIL B
SCHEMATIC 9
91
SCHEMATIC
SCHEMATIC COIL B 9
1
COIL COIL
B B 9
8 2
1 1 5 (Bottom
(Bottom View)View) 61 COIL
COIL B B 9
8 2
3.5
1 1 (Coil
(Coil A LastAEnergized)
Last Energized)
(Bottom
COIL COIL
B
  Resistive:
8
9
B 91A/28Vdc
2
1 1
View)View)
  D = Internal diode for coil 8 8 2 2 8 8 2 2
(Bottom
8 8 2 2
7 3 6 120 7 3 4.5   Inductive: 200mA/28Vdc
7 3 (320mH)
  transient suppression 7 7 3 3 7 7 3 3 7 7 3 3
on

6 6 6
56 46 S422 9 280 56 46 6.8   Lamp: 100mA/28Vdc
56 4 6
54 4 5 45 4 5 45 4
  DD = Internal diode for coil 5
S422D 12 500 9.0   Low Level: 10 to 50 uA/10 to 50 mV
COIL A COIL A COIL A
  transient suppression and COIL COIL
A A 18 1130 13.5 COIL COIL
A A COIL COIL
A A
SCHEMATIC SCHEMATIC
  polarity reversal protection SCHEMATIC
SCHEMATIC SCHEMATIC
SCHEMATIC SCHEMATIC
(Coil A Last
(Bottom
Energized)
(Coil A(Coil
Last A
View) Last Energized)
Energized)
26 2000 (Coil (Coil
A Last
A(Coil
Last A
18.0
Energized)
Last Energized)
Energized)
(Bottom View) (Coil A Last SCHEMATIC
SCHEMATIC
Energized)
Vibration Shock (Bottom (Bottom
View) View)
5 48
(Bottom
(Bottom View) View)
4.5   Resistive: 1A/28Vdc
(Coil A(Coil
(Bottom
(Bottom
(Bottom View) View)
Last A
View)Last Energized)
Energized)

30 g’s 6 msec, 6 97 5.5   Inductive: 200mA/28Vdc (320mH)

10 g’s to 500 Hz
half-sine 9 280 7.8   Lamp: 100mA/28Vdc
S422DD
Temperature 12 500 10.0   Low Level: 10 to 50 uA/10 to 50 mV
422 422D 422DD
422 422 18 1130 422D
422D 14.5 422DD
422DD
  Storage: –65°C to +125°C 422H
422H422H
422K 26 2000 19.0
  Operating: –55°C to +85°C 422K422K
722
COIL B 722 722 COIL B COIL B
COIL COIL
B B COIL COIL
B B COILCOIL
B B
10 10 10
9 101 10 9 10 1 10 9 10 1 10
9 9 1 9 9 1 1 9 9 1 1
1 2 2
8 2 8 8
2 2 2 2
7
8 8
3
2 2
S422 7
8 8
3 S422D 7
8 8
3 S422DD
3 3 7 3 3 3 3
67
7 67 6
7 7
65 64 65 64 65 64
4 4 4 4 4 4
5 5 5 5 5 5

COIL A COIL A COIL A

Schematics as viewed from terminals COIL COIL
A A COIL COIL
A A COILCOIL
A A
SCHEMATIC SCHEMATIC
(Coil A Last SCHEMATIC
SCHEMATIC
Energized) SCHEMATIC
SCHEMATIC
(Coil A Last Energized) SCHEMATIC
(Coil A(Coil
(Bottom Last A Last Energized)
Energized)
View) (Coil A(Coil
(Bottom Last A Last Energized)
Energized)
View) (Coil A Last SCHEMATIC
SCHEMATIC
Energized)
(Bottom (Bottom
View) View) (Bottom (Bottom
View) View) (Coil A(Coil
(Bottom Last A
View)Last Energized)
Energized)
(Bottom (Bottom
View) View)

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 15

 ESTABLISHED RELIABILITY T2R RELAYS

Series ER114 Electromechanical Relays

The Series ER114 Centigrid® relay is an ultraminiature, hermetically sealed, armature relay. Its low profile • All welded construction
height .275” (7 mm) and .100” (2.54 mm) grid spaced terminals, which precludes the need for spreader pads, • Unique uni-frame design providing high
make it ideal for applications where extreme packaging density and/or close PC board spacing are required. magnetic efficiency and mechanical rigidity
The basic design and internal construction are similar to the standard Teledyne DPDT TO-5 relay (e.g., • High force/mass ratio for resistance to shock
Series ER412). and vibration
The Series ER114D and ER114DD relays have internal discrete silicon diodes for coil suppression and • Precious metal alloy contact material with
polarity reversal protection. gold plating assures excellent high current
By virtue of its inherently low intercontact capacitance and contact circuit losses, the ER114 relay has proven and dry circuit switching capabilities
to be an excellent ultraminiature RF switch for frequency ranges well into the UHF spectrum. A typical RF
application for the ER114 relay is in handheld radio transceivers, wherein the combined features of good
RF performance, small size, low coil power dissipation and high reliability make it a preferred method of
Transmit-Receive switching.

Relay Type Nominal Coil

  DPDT Non-Latching Part No. Voltage Resistance P.U.V D.O.V (Vdc) Contact Load Rating

m
Diode Options (Vdc) (Ω) (Vdc) (max.) min. max.

  D = Internal diode for coil 5 50 3.5 0.14 2.3   Resistive: 1A/28Vdc

co
  transient suppression 6 98 4.5 0.18 3.2   Inductive: 200mA/28Vdc (320mH)
  DD = Internal diode for coil ER114 9 220 6.8 0.35 4.9   Lamp: 100mA/28Vdc
  transient suppression and ER114D 12 390 9.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV

s.
  polarity reversal protection 18 880 13.5 0.59 10.0
Vibration Shock 26 1560 18.0 0.89 13.0
nt
30 g’s 75 g’s 6 msec, 5 39 4.0 0.6 2.8   Resistive: 1A/28Vdc

to 3000 Hz half-sine 6 78 5.0 0.7 3.4   Inductive: 200mA/28Vdc (320mH)

ne

9 220 7.8 0.8 5.3   Lamp: 100mA/28Vdc

Acceleration Temperature ER114DD
12 390 10.0 0.9 6.5   Low Level: 10 to 50 uA/10 to 50 mV
Operating &
Storage: 18 880 14.5 1.1 10.0
po
E S TA B L I S H E D R E L I A B I L I T Y

50 g’s
–65°C to +125°C 26 1560 19.0 1.4 13.0

Series ER116C Electromechanical Relays

m

The ER116C Centigrid® relay is an ultraminiature, hermetically sealed, armature relay capable of being • All welded construction
directly driven by most IC logic families. Its low profile height and .100” (2.54 mm) grid spaced terminals, • Unique uni-frame design providing high
co

which preclude the need for spreader pads, make it ideal for applications where extreme packaging density magnetic efficiency and mechanical rigidity
and/or close PC board spacing are required. • High force/mass ratio for resistance to shock
The Series ER116C utilizes an internal silicon diode for coil suppression, a Zener diode to protect the and vibration
MOSFET gate input, and an N-channel enhancement mode MOSFET chip, which enables direct relay
e

interfacing with most Microprocessor and IC logic families (CMOS, TTL and MOS).
lin

Relay Type 114, 134Nominal Coil

114D, 134D
on

S114/S134
  DPDT Non-Latching Coil Current S114D/S134D
Part No. Voltage 172
Operating P.U.V Contact Load Rating
(mA) (Vdc) 172D
CMOS Feature (Vdc) Power (mW) (max.)
Min. Max.
  Internal power MOSFET
8
5 96.5
7 1 132.3 641 4.0  7 Resistive:
1 1A/28Vdc
  driver, Zener diode gate protec- 6
8
2
6 60.3 83.9 462 4.9   Inductive:
6 200mA/28Vdc
2 (320mH)
  tion, and diode coil suppression
9 5 4
33.1 3 47.1 368 7.3  5 Lamp: 100mA/28Vdc
3
Vibration Shock ER116C 4
12 24.9 36.1 369 9.8   Low Level: 10 to 50 uA/10 to 50 mV
30 g’s 75 g’s 6 msec, 18 SCHEMATIC
16.1 24.1 368 14.6 SCHEMATIC
114, 134 114, 134 (Bottom View) (Bottom View)
to 3000 Hz half-sine
S114/S134 S114/S134 114D, 134D 114D, 134D
26 12.9 19.9 450 19.5 116C, 136C
172 172 S114D/S134D S114D/S134D
114DD, 134DD
Acceleration Temperature 172D 172D
S114DD/S134DD
Operating &
–
50 g’s Storage: 9
10 +1
7 1 8 88
7 1 7 1 77 11
–65°C
6
8to +125°C
2 6
8
2 8 2
6 2
66 2
2 PIN 1: + SUPPLY
4 7 3 PIN 9: – SUPPLY
5 3 4 PIN 10: GATE
5 3 5 3 5 3
4 5 4 3 4
4 6

SCHEMATIC SCHEMATIC SCHEMATIC

(Bottom View) SCHEMATIC
ER114 ER114D
(Bottom View) ER114DD
SCHEMATIC
(Bottom View) ER116C
SCHEMATIC
(Bottom View) (Bottom View) (Bottom View)
114DD, 134DD
P.U.V = Pick-Up Voltage S114DD/S134DD 114DD, 134DD Schematics as viewed from terminals
116C, 136C
S114DD/S134DD
122C
8
7 1
Page 16 (800) 284-7007 • www.teledynerelays.com •7 +4498–(0) 1236
10 453124
+1 • www.teledyne-europe.com 10 +
© 2010 TELEDYNE RELAYS
1 9 1
6 2
6 8 2 2
5 3 8 2 PIN 4: GATE A
4 PIN 1: + SUPPLY PIN 5: – SUPPLY
 ESTABLISHED RELIABILITY T2R RELAYS

Series ER134 Electromechanical Relays

The ER134 sensitive Centigrid® relay retains the same features as the ER114 standard Centigrid® relay with • All welded construction
only a minimal increase in profile height .375” (9.53 mm). Its .100” (2.54 mm) grid spaced terminals, which • Unique uni-frame design providing high
preclude the need for spreader pads, and its low profile make the ER134 relay ideal for applications where magnetic efficiency and mechanical rigidity
high packaging density is important. • High force/mass ratio for resistance to shock
The Series ER134D and ER134DD have internal discrete silicon diodes for coil suppression and polarity and vibration
reversal protection. • Precious metal alloy contact material with
The sensitive ER134 Centigrid® relay has a high resistance coil, thus requiring extremely low operating gold plating assures excellent high current
power (200 mw typical). The advantages of reduced heat dissipation and power supply demands are a plus. and dry circuit switching capabilities

Relay Type Nominal Coil

  DPDT Non-Latching Part No. Voltage Resistance P.U.V D.O.V (Vdc) Contact Load Rating
Diode Options (Vdc) (Ω) (Vdc) (max.) min. max.

m
  D = Internal diode for coil 5 100 3.5 0.12 2.5   Resistive: 1A/28Vdc
  transient suppression 6 200 4.5 0.18 3.2   Inductive: 200mA/28Vdc (320mH)

co
  DD = Internal diode for coil ER134 9 400 6.8 0.35 4.9   Lamp: 100mA/28Vdc
  transient suppression and ER134D 12 800 9.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV
  polarity reversal protection 18 1600 13.5 0.59 10.0

s.
Vibration Shock 26 3200 18.0 0.89 13.0

30 g’s 75 g’s 6 msec, 5 64 3.7 0.7 2.6   Resistive: 1A/28Vdc

nt
to 3000 Hz half-sine 6 125 4.8 0.8 3.0   Inductive: 200mA/28Vdc (320mH)
9 400 8.0 0.9 4.5   Lamp: 100mA/28Vdc
Acceleration Temperature ER134DD
ne

12 800 11.0 1.0 5.8   Low Level: 10 to 50 uA/10 to 50 mV

Operating & 18 1600 14.5 1.1 9.0
50 g’s Storage: 26 3200 19.0 1.3 13.0
po

–65°C to +125°C

Series ER136C Electromechanical Relays

m

The sensitive ER136C Centigrid® relay is an ultraminiature, hermetically sealed, armature relay capable • All welded construction
of being directly driven by most IC logic families. Its low profile height and .100” (2.54 mm) grid spaced • Unique uni-frame design providing high
co

terminals, which precludes the need for spreader pads, make it ideal for applications where extreme magnetic efficiency and mechanical rigidity
packaging density and/or close PC board spacing are required. • High force/mass ratio for resistance to shock
The sensitive ER136C Centigrid® relay has a high resistance coil, thus requiring extremely low operating and vibration
power (200 mW, typical). The advantages of reduced heat dissipation and power supply demands are a
e

plus.
The sensitive Series ER136C utilizes an internal silicon diode for coil suppression, a Zener diode to protect
lin

the MOSFET gate input, and an N-channel enhancement-mode MOSFET chip that enables direct relay
interfacing with most microprocessor and IC logic families (CMOS, TTL and MOS).
114, 134
114D, 134D
on

Relay Type Nominal

S114/S134 Coil
172 S114D/S134D
  DPDT Non-Latching Coil Current 172D
Part No. Voltage Operating P.U.V Contact Load Rating
(mA) (Vdc)
CMOS Feature (Vdc) Power (mW) (max.)
Min.
7 1
Max. 8
  Internal power MOSFET 6
8
2
7 1
5 43.0 56.0 250 4.0   Resistive: 1A/28Vdc
  driver, Zener diode gate protec- 6 2
6 27.0
5 4 3 33.0 180 4.9   Inductive: 200mA/28Vdc (320mH)
  tion, and diode coil suppression 5
4 3
9 17.8 26.4 203 7.3   Lamp: 100mA/28Vdc
Vibration Shock ER136C
12 11.3
SCHEMATIC17.7 180 9.8   Low Level: 10 to 50 uA/10 to 50 mV
SCHEMATIC
30 g’s 75114,
g’s 134
6 msec, 114, 134 (Bottom View) (Bottom View)
S114/S134 S114/S134 18 114D,8.4
134D 13.8 114D, 134D 14.6
203
S114D/S134D S114D/S134D 116C, 136C
to 3000 Hz half-sine
172 172 26
114DD, 134DD
172D 5.8 10.2 219
172D
19.5
S114DD/S134DD
Acceleration Temperature
–
Operating & 9
10 +1
7 1 8 88
Storage: 7 1 7 1 77
50 g’s 6
8
2 8
11
6 2 8 2
–65°C to +125°C 6 2
66 2
2 PIN 1: + SUPPLY
4 7 3 PIN 9: – SUPPLY
5 3 4 PIN 10: GATE
5 3 5 3 5 3
4 5 4 3 4
4 6

SCHEMATIC SCHEMATIC SCHEMATIC

(Bottom View) SCHEMATIC
ER134 ER134D
(Bottom View) ER134DD
SCHEMATIC
(Bottom View) ER136C
SCHEMATIC
(Bottom View) (Bottom View) (Bottom View)
114DD, 134DD
Schematics as viewed from terminals S114DD/S134DD 114DD, 134DD P.U.V = Pick-Up Voltage
116C, 136C
S114DD/S134DD D.O.V = Drop-Out Voltage
122C
8
7 1
© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT
7 9
8–TO CHANGE
10 +1 WITHOUT NOTICE 10 +
Page 17
1 9 1
6 2
6 8 2 2
5 3 8 2 PIN 4: GATE A
4 PIN 1: + SUPPLY PIN 5: – SUPPLY
 ESTABLISHED RELIABILITY T2R RELAYS

Series ER411 & ER431 Electromechanical Relays

The TO-5 relay, originally conceived and developed by Teledyne, has become one of the industry standards • All welded construction
for low-level switching from dry circuit to 1 ampere. Designed specifically for high-density PC board • Unique uni-frame design providing high
mounting, its small size and low coil power dissipation make the ER411 relay one of the most versatile magnetic efficiency and mechanical rigidity
ultraminiature relays available. • High force/mass ratio for resistance to shock
The Series ER411D and ER411DD relays have internal discrete silicon diodes for coil suppression and and vibration
polarity reversal protection. The hybrid ER411T relay features an internal silicon suppression diode and • Precious metal alloy contact material with
transistor driver. This hybrid package reduces required PC board floor space by reducing the number of gold plating assures excellent high current
external components needed to drive the relay. and dry circuit switching capabilities
The sensitive ER431 relay has a high resistance coil, thus requiring extremely low operating power (150 mw
typical). The advantages of reduced heat dissipation and power supply demands are a plus.
The Series ER431D and ER431DD relays have internal discrete silicon diodes for coil suppression and
polarity reversal protection. The hybrid ER431T relay features an internal silicon suppression diode and
transistor driver. This hybrid package reduces required PC board floor space by minimizing the number of
external components needed to drive the relay.

Relay Type Nominal Coil

m
  SPDT Non-Latching Part No. Voltage Resistance P.U.V D.O.V (Vdc) Contact Load Rating
(Vdc) (Ω) (Vdc) (max.)

co
Coil Type min. max.

  ER411 = Standard Coil 5 63 3.7 0.15 2.4   Resistive: 1A/28Vdc

  ER431 = Sensitive Coil 6 125 4.5 0.18 2.8   Inductive: 200mA/28Vdc (320mH)

s.
Diode Options ER411 9 280 6.8 0.35 4.2   Lamp: 100mA/28Vdc
  D = Internal diode for coil ER411D 12 500 9.0 0.40 5.6   Low Level: 10 to 50 uA/10 to 50 mV
nt
  transient suppression 18 1130 13.5 0.58 8.4
  DD = Internal diode for coil 26 2000 18.0 0.89 10.4
ne

  transient suppression and 5 50 4.5 0.15 2.4   Resistive: 1A/28Vdc

  polarity reversal protection 6 98 5.5 0.18 2.8   Inductive: 200mA/28Vdc (320mH)

9 280 7.8 0.35 4.2   Lamp: 100mA/28Vdc
  T = Internal transistor drive ER411DD
po
E S TA B L I S H E D R E L I A B I L I T Y

12 500 10.0 0.40 5.6   Low Level: 10 to 50 uA/10 to 50 mV

  and coil transient suppression
18 1130 14.5 0.58 8.4
  diode
26 2000 19.0 0.89 10.4
Vibration Shock
m

5 63 3.9 0.15 2.4   Resistive: 1A/28Vdc

30 g’s 75 g’s 6 msec,
6 125 5.2 0.18 2.8   Inductive: 200mA/28Vdc (320mH)
to 3000 Hz half-sine
co

9 280 7.8 0.35 4.2   Lamp: 100mA/28Vdc

Acceleration Temperature ER411T
12 500 10.0 0.40 5.6   Low Level: 10 to 50 uA/10 to 50 mV
Operating & 18 1130 14.5 0.58 8.4
Storage:
e

50 g’s
26 2000 19.0 0.89 10.4
–65°C to +125°C
lin

411/431 411D/431D 411DD/431DD 5 125

411T/431T 3.7 0.15 2.0   Resistive: 1A/28Vdc
6 255 4.5 0.18 2.8   Inductive: 200mA/28Vdc (320mH)
4 1 4
ER431 9 630
9 1 6.8 0.35 4.2   Lamp: 100mA/28Vdc
4
on

5 1 5 1 2
ER411 5 ER431D 12 8 1025 9.0 0.41 5.6   Low Level: 10 to 50 uA/10 to 50 mV
3
3 2 ER431 18 7
2300 13.5 0.58 8.4
3 2 3 2 6 4
431 411D/431D 411DD/431DD 411T/431T 26 4000 18.0 0.89 10.4
SCHEMATIC SCHEMATIC SCHEMATIC 5 100 4.5 0.15 2.4   Resistive: 1A/28Vdc
(Bottom View) (Bottom View) (Bottom View) SCHEMATIC
6 200
(Bottom View) 5.5 0.18 2.8   Inductive: 200mA/28Vdc (320mH)
1 4 4 9 1
5
5 1
ER411D 1
8
2 9 630 7.8 0.35 4.2   Lamp: 100mA/28Vdc
ER431DD3
2
ER431D 7 12 1025 10.0 0.40 5.6   Low Level: 10 to 50 uA/10 to 50 mV
3 2 3 2 6 4
18 2300 14.5 0.58 8.4
31D 411DD/431DD 411T/431T
TIC SCHEMATIC SCHEMATIC 26 4000 19.0 0.89 10.4
w) (Bottom View) (Bottom View) SCHEMATIC
412/432 412D/432D 412DD/432DD
(Bottom View) 5 125 412T/432T 3.6 0.15 2.0   Resistive: 1A/28Vdc
412H/432H 412DV/432DV 412DDV
255 712TN/732TN
1 9
1
4
5 1 2 6 4.8 0.18 2.8   Inductive: 200mA/28Vdc (320mH)
412K 8 712D/732D
ER411DD
412V 3 9 630 7.8 0.35 4.2   Lamp: 100mA/28Vdc
ER431DD
7
ER431T
2 3 712/732
2 6 4 12 1025 10.0 0.41 5.6   Low Level: 10 to 50 uA/10 to 50 mV
1DD 411T/431T 18 2300 14.5 0.58 8.4
C SCHEMATIC
) (Bottom View) SCHEMATIC 26 4000 19.0 0.89 10.4
2/432 9 412D/432D
1 9 412DD/432DD
1 View)
(Bottom 412T/432T 10
1
2H/432H 8 412DV/432DV
1 2 8 412DDV 2
9 712TN/732TN 9
1
2K
9
7 712D/732D
2 3 Schematics as viewed
8 from 2terminals 8 2 P.U.V = Pick-Up Voltage
8 ER411T
7 3
2V 6 3 4 4
7 3 7 3
D.O.V = Drop-Out Voltage
2/732
7 ER431T
6
6 4 6 4
6 4

SCHEMATIC SCHEMATIC SCHEMATIC SCHEMATIC

(Bottom View) (Bottom View) (Bottom View) (Bottom View)
SCHEMATIC
D/432D 9 412DD/432DD 412T/432T
1 10
1
DV/432DV
2 Page 818(Bottom View)
412DDV2 9 (800) 284-7007
1
712TN/732TN • www.teledynerelays.com
9
1
• +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
8 2 8 2
D/732D3 3
7 3
4 7 3 7
6 4
6 4 6 4
 ESTABLISHED RELIABILITY T2R RELAYS

Series ER412 & ER432 Electromechanical Relays

The TO-5 relay, originally conceived and developed by Teledyne, has become one of the industry standards • All welded construction
for low-level switching from dry circuit to 1 ampere. Designed specifically for high-density PC board • Unique uni-frame design providing high
mounting, its small size and low coil power dissipation make the ER412 relay one of the most versatile magnetic efficiency and mechanical rigidity
ultraminiature relays available. • High force/mass ratio for resistance to shock
The Series ER412D and ER412DD relays have internal discrete silicon diodes for coil suppression and and vibration
polarity reversal protection. The hybrid ER412T relay features an internal silicon suppression diode and • Precious metal alloy contact material with
transistor driver. This hybrid package reduces required PC board floor space by reducing the number of gold plating assures excellent high current
external components needed to drive the relay. and dry circuit switching capabilities
The sensitive ER432 relay has a high resistance coil, thus requiring extremely low operating power (200 mw
typical). The advantages of reduced heat dissipation and power supply demands are a plus.
The Series ER432D and ER432DD relays have internal discrete silicon diodes for coil suppression and
polarity reversal protection. The hybrid ER432T relay features an internal silicon suppression diode and
transistor driver. This hybrid package reduces required PC board floor space by minimizing the number of
external components needed to drive the relay.

Relay Type Nominal Coil

m
  DPDT Non-Latching Part No. Voltage Resistance P.U.V D.O.V (Vdc) Contact Load Rating
(Vdc) (Ω) (Vdc) (max.)

co
Coil Type min. max.

  ER412 = Standard Coil 5 50 3.5 0.14 2.3   Resistive: 1A/28Vdc

  ER432 = Sensitive Coil 6 98 4.5 0.18 3.2   Inductive: 200mA/28Vdc (320mH)

s.
Diode Options ER412 9 220 6.8 0.35 4.9   Lamp: 100mA/28Vdc
411/431
  D 411D/431D
= Internal diode for coil ER412D
411DD/431DD 12 390
411T/431T 9.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 uA
nt
  transient suppression 18 880 13.5 0.59 10.0
 4 DD =1Internal diode for
4 coil
26 9
1560
1 18.0 0.89 13.0
4
5 1 5 1
ne

  transient suppression and

5 5 8 39 2 3.9 0.6 2.8   Resistive: 1A/28Vdc
7 3
3 2
  polarity reversal protection
3 2 3 2 6 78 5.2 0.7 3.4   Inductive: 200mA/28Vdc (320mH)
6 4
1/431 411DD/431DD 9 220 7.8 0.8 5.3   Lamp: 100mA/28Vdc
  T411D/431D
= Internal transistor drive ER412DD
411T/431T
po

SCHEMATIC SCHEMATIC SCHEMATIC 12 390 10.0 0.9 6.5   Low Level: 10 to 50 uA/10 to 50 uA
 (Bottom
andView)
coil transient suppression
(Bottom View) (Bottom View) SCHEMATIC
18 880
(Bottom View) 14.5 1.1 10.0
1   4diode 4
5
9 1
1 1 2
5 8 26 1560 19.0 1.4 13.0
Vibration Shock
m

7 3
2 3 2 3 2
5 50 3.5 0.14 2.3   Resistive: 1A/28Vdc
30 g’s 75 g’s 6 msec, 6 4
431D 411DD/431DD 411T/431T 6 98 4.5 0.18 3.2   Inductive: 200mA/28Vdc (320mH)
to 3000 Hz half-sine
co

MATIC SCHEMATIC SCHEMATIC 9 220 6.8 0.35 4.9   Lamp: 100mA/28Vdc

View) (Bottom View)
Acceleration (Bottom View)
Temperature ER412T
SCHEMATIC
412/432 412D/432D
9 1 412DD/432DD
(Bottom View) 12 390
412T/432T 9.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV
4
5 412H/432H 412DV/432DV 412DDV 712TN/732TN
1 1 Operating
8 & 2 18 880 13.5 0.59 10.0
412K 712D/732D
Storage:
e

50 g’s 7 3
2 3 412V2 26 1560 18.0 0.89 13.0
712/732 –65°C to 6+125°C4
lin

5 100 3.5 0.14 2.5   Resistive: 1A/28Vdc

DD 411T/431T
IC SCHEMATIC 6 200 4.5 0.18 3.2   Inductive: 200mA/28Vdc (320mH)
w) (Bottom View) SCHEMATIC
412/432 9 412D/432D
1
(Bottom View)
412DD/432DD ER432
412T/432T 9 400
10 6.8 0.35 4.9   Lamp: 100mA/28Vdc
9 1
on

412H/432H 9 1412DV/432DV 412DDV 712TN/732TN

1
8
2
2 ER412
8 2
9 ER432D 12 9 850 1 9.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV
412K 8 712D/732D 8 2 8 2
412V 7
7
3
3 ER432
7 3 18 7 1600 3 13.5 0.59 10.0
6 4 7 3
6 4
712/732 6 4 6 4 26 63300 4 18.0 0.89 13.0
5 64 3.7 0.7 2.6   Resistive: 1A/28Vdc
SCHEMATIC SCHEMATIC SCHEMATIC SCHEMATIC
2D/432D SCHEMATIC
412DD/432DD
(Bottom View) 412T/432T
(Bottom View) (Bottom View) 6 125
(Bottom View) 4.8 0.8 3.0   Inductive: 200mA/28Vdc (320mH)
1 (Bottom View) 10
2DV/432DV 9 412DDV1 712TN/732TN
1
2 8 2
ER412D
9 9
1 9 400 8.0 0.9 4.5   Lamp: 100mA/28Vdc
2D/732D 8 2 ER432DD
8 2
3
7 3 ER432D
7 3 7 3 12 850 11.0 1.0 5.8   Low Level: 10 to 50 uA/10 to 50 mV
4 4
6
6 4 6 4 18 1600 14.5 1.1 9.0
26 3300 19.0 1.3 13.0
HEMATIC SCHEMATIC SCHEMATIC SCHEMATIC
ttom View) (Bottom View) (Bottom View)
10
(Bottom View) 5 100 3.6 0.14 2.5   Resistive: 1A/28Vdc
32DD
1 412T/432T
1
2
9
712TN/732TN
9
1 6 200 4.8 0.18 3.2   Inductive: 200mA/28Vdc (320mH)
2
8 ER412DD
8 2
3
3 7 3 9 400 7.8 0.35 4.9   Lamp: 100mA/28Vdc
4
7 ER432DD ER432T
6 4 6 4 12 850 11.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV
18 1600 14.5 0.59 10.0
MATIC SCHEMATIC SCHEMATIC
View) (Bottom View) (Bottom View) 26 3300 19.0 0.89 13.0
10
9
2 1 Schematics as viewed from terminals P.U.V = Pick-Up Voltage
8 2 ER412T
3 7 3 ER432T D.O.V = Drop-Out Voltage
6 4

C SCHEMATIC
(Bottom View)

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 19

 ESTABLISHED RELIABILITY T2R RELAYS

Series 255, 256, 257, 258 Electromechanical Relays

The Series 255 is an industry-standard, half-size, latching crystal can relay. It has a wide range of switching • All welded construction
capabilities ranging from low level to 2 amps. The Series J255/255 latching relay configuration is double- • Wire leads, gold-plated or solder-coated
pole double-throw (DPDT), so the relay offers excellent switching density and versatility. • Matched seal for superior hermeticity
Half-Size Crystal Can Features: • Gold-plated contact assembly
  • Low level to 2 amps • Modernized assembly process
  • Wide range of switching capabilities • Advanced cleaning techniques
  • Smallest relay package capable of switching 2 amps
  • Modernized assembly process
  • Lead-free (gold-plated wire lead only)

Relay Type Nominal Coil

  DPDT Magnetic-Latching Set & Reset Voltage
Part No. Voltage Resistance Contact Load Rating
(Vdc) J255 J255 256 256
Vibration (Vdc) (Ω) B3 A2 A1 A3 A3
Min. Max.X1
B3 A2 A1
B2 Y1 B2 B1 Y1 B1
X1

  30G, 10-2500 Hz Y2 Y2 X2 X2 X2 X2

5 45 1.0 3.8   Resistive: 2A/28Vdc

m
Y2 Y2
Y1 Y1
  (Sinusoidal) 255 B2 A3
A1 X1 A1 A2
X1
B3 A2 B3

6 63 1.3 4.5   Inductive: 0.75A/28Vdc (320mH)

B1 B1 B2 A3

Shock 256 SCHEMATIC

SCHEMATIC SCHEMATIC
SCHEMATIC
12 254 2.6 9.0
(Coil X Last Energized)
  Intermediate Current:
X Last Energized)0.1A/28Vdc

co
(Coil X Last Energized) (Coil X Last Energized)
(Coil

  100G, 6 msec half-sine 257 (Bottom View) (Bottom View) (Bottom View) (Bottom View)

26 1000 5.2 18.0   Lamp: 0.16A/28Vdc

  (Specified Pulse) 258
26 1000 5.2 18.0   Low Level: 10 to 50 uA/10 to 50 mV
Temperature

s.
255
J255 J255 256 256
256 257
257 257 258 258
258
  Operating & Storage: B3 A2 B3 A2 A1 A1 A3
B2
A3
Y1 B2 B1 Y1 B1
B3 A2 B3 A2 A1 A3
A1 B2
A3
X2 B2 B1 X2
X1 X1 B1
X1 X1

  –65°C to +125°C Y2 Y2 X2 X2
X2 X2
nt Y2 Y2 X2 X2

Y2 Y2 Y2 Y1
Y2 Y1
Y1 Y1 Y1 Y1
A1 A2 X1 B3 A2 B3 A1 X1 A2 B3
X1 A1 A1 X1 A2 B3
B1 B1 B2 A3 B2 A3 B1 B2 A3 B2 A3
B1

SCHEMATIC
SCHEMATIC SCHEMATIC
SCHEMATIC SCHEMATIC SCHEMATIC
SCHEMATIC
ne
(Coil X Last Energized)
(Coil X Last Energized)
SCHEMATIC
(Coil X Last Energized)
(Coil X Last Energized) (Coil X Last Energized)
(Coil X Last Energized) (Coil Y Last Energized)
(Coil Y Last Energized)
(Bottom View)(Bottom View) (Bottom View)(Bottom View) (Bottom View) (Bottom View) (Bottom View) (Bottom View)

Series ER421 Electromechanical Relays

po
E S TA B L I S H E D R E L I A B I L I T Y

The magnetic-latching TO-5 relay, originally conceived 257

and
257
developed by 258
Teledyne,258
has become one of • All welded construction
the industry standards for low-level switching from dry circuit to 1 ampere. Designed for high-density PC • Unique uni-frame design providing high
B3 A2 B3 A2 A1 A1 A3 A3

board mounting, its small size and low coil power dissipation make the ER421 relay one of the most versatile
Y2
X1
Y2 X2
X1
X2
B2 X2 B2 B1 X2 B1

magnetic efficiency and mechanical rigidity

ultraminiature relays available. Y2 Y2Y1 Y1
• High force/mass ratio for resistance to shock
m

Y1 Y1

The Series ER421D and ER421DD utilize discrete silicon diodes for coil suppression and polarity reversal
B1 B1 B2 A3 B2 A3
A1 X1 A1 A2 X1 B3 A2 B3

and vibration
protection. SCHEMATIC SCHEMATIC SCHEMATIC SCHEMATIC • Precious metal alloy contact material with
The Series ER421 magnetic-latching relays are (Coil Xideally
Last Energized) suited
(Coil X Last Energized) for applications (Coil Y Lastwhere
(Coil Y Last Energized) Energized) coil power dissipation
co

(Bottom View)(Bottom View) (Bottom View)(Bottom View) gold plating assures excellent high current
must be minimized. The relays can be operated with a short duration pulse. After the contacts have and dry circuit switching capabilities
transferred, no external holding power is required. The magnetic-latching feature of the Series ER421
provides a “memory” capability, since the relays will not reset upon removal of coil power.
e
lin

Relay Type Nominal Coil

  SPDT Magnetic-Latching Part No. Voltage Resistance Set & Reset Contact Load Rating
(Vdc) (Ω) Voltage (Vdc)
Diode Options
on

5 61 3.5   Resistive: 1A/28Vdc

  D = Internal diode for coil
6 120 4.5   Inductive: 200mA/28Vdc (320mH)
  transient suppression
9 280 6.8   Lamp: 100mA/28Vdc
  DD = Internal diode for coil ER421
12 500 9.0   Low Level: 10 to 50 uA/10 to 50 mV
  transient suppression and 18 1130 13.5
  polarity reversal protection 26 2000 18.0
Vibration Shock 5 61 3.7   Resistive: 1A/28Vdc
30 g’s 100 g’s 6 msec, 6 120 4.5   Inductive: 200mA/28Vdc (320mH)
to 3000 Hz half-sine 9 280 6.8   Lamp: 100mA/28Vdc
ER421D
Acceleration Temperature 12 500 9.0   Low Level: 10 to 50 uA/10 to 50 mV
Operating & 18 1130 13.5
50 g’s Storage: 26 2000 18.0
–65°C to +125°C 5 48 4.5   Resistive: 1A/28Vdc
6 97 5.5   Inductive: 200mA/28Vdc (320mH)
9 280 7.8   Lamp: 100mA/28Vdc
ER421DD
*See Schematics on Page 21 12 500 10.0   Low Level: 10 to 50 uA/10 to 50 mV
18 1130 14.5
26 2000 19.0

Page 20 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 ESTABLISHED RELIABILITY T2R RELAYS

Series ER420 & ER422 Electromechanical Relays

The magnetic-latching TO-5 relay, originally conceived and developed by Teledyne, has become one of the • All welded construction
industry standards for low-level switching from dry circuit to 1 ampere. Designed for high-density PC board • Unique uni-frame design providing high
mounting, its small size and low coil power dissipation make the ER420 & ER422 relays some of the most magnetic efficiency and mechanical rigidity
versatile ultraminiature relays available. • High force/mass ratio for resistance to shock
The Series ER420D/ER422D and ER420DD/ER422DD utilize discrete silicon diodes for coil suppression and and vibration
polarity reversal protection. • Precious metal alloy contact material with
The Series ER420/ER422 magnetic-latching relays are ideally suited for applications where coil power gold plating assures excellent high current
dissipation must be minimized. The relays can be operated with a short duration pulse. After the contacts and dry circuit switching capabilities
have transferred, no external holding power is required. The magnetic-latching feature of the Series ER420/
ER422 relays provide a “memory” capability, since the relays will not reset upon removal of coil power.

Relay Type Nominal Coil

  DPDT Magnetic-Latching Part No. Voltage Resistance Set & Reset Contact Load Rating
(Vdc) (Ω) Voltage (Vdc)
Grounding Options
421 421421 5 61 3.5
421D
421D 421D   Resistive: 1A/28Vdc
421DD
421DD
421DD

m
  420 = Individual
ER420 6 120 4.5   Inductive: 200mA/28Vdc (320mH)
  422 = Common
ER422 9 280 6.8   Lamp: 100mA/28Vdc

co
Diode Options ER420D 12 500 9.0   Low Level: 10 to 50 uA/10 to 50 mV
  D = Internal diode for coil COIL
COIL BCOIL B B COIL
COIL
COIL B B B
9 9 ER422D B COIL
COIL COIL
9 B 18B 1130 9 9 913.5 9 9 9
1
1 1 1 1 1 1 1 1
  transient suppression 8 8 8 26 20008 8 8 18.02 8 8 8

s.
27 2 2 27 2 2 2 2
7 47 4 4 7 47 4 4 7 47 7 4 4
  DD = Internal diode for coil 5 48 4.5   Resistive: 1A/28Vdc
COIL A6 6 6 6 6 6 6 6 6
COIL
COIL A A 421 421421 421D421D
421D COIL 421DD
421DD
421DD
  transient suppression and 6 97 COIL
5.5 COIL A A  A Inductive: 200mA/28Vdc A COIL
COIL COIL
(320mH) A A
nt
  polarity reversal protection ER420DD 9 280 7.8   Lamp: 100mA/28Vdc
SCHEMATIC
SCHEMATIC
SCHEMATIC SCHEMATIC
SCHEMATIC
SCHEMATIC
SCHEMATIC SCHEMATIC
SCHEMATIC
Vibration Shock (Coil
(Coil A Last (Coil
A LastA Energized)
Energized)Last Energized)
View)(Bottom
(Bottom (Bottom View)View)
ER422DD 12 500 (Coil (Bottom
(Coil
A Last A LastA10.0
(Coil
Energized)Last Energized)
Energized)
View)(Bottom
(Bottom View)View)
  Low Level: 10 to (Coil
50
(Coil A Last
uA/10
(Coil to 50 mV
A LastA Energized)
Energized)Last Energized)
ne

View)(Bottom
(Bottom (Bottom View)View)
30 g’s 100 g’s 6 msec, 18 B 1130 14.5 COIL COIL
B COIL
B B
9 9 COIL COIL B B COIL COIL
B COIL B B
COIL 9 9 9 9 9 9
19 1 1 1 1 1 1 1 1
to 3000 Hz half-sine 26 2000 19.0
8 8 8 8 8 8 8 8 8
2 2 2 7 7 2 2 2 2 2 2
7 47 74 7 7
Acceleration Temperature 74 4 4 4 4 74 4
po

COIL COIL A A 6420 6 4206420

A COIL 6 6 420D
6 420D
420D 6 420DD
6 420DD
6 420DD
Operating & COIL COIL
A COIL
A A COIL COIL
A COIL
A A
50 g’s Storage:
SCHEMATIC
–65°C to +125°CCOIL BCOIL SCHEMATIC
SCHEMATIC SCHEMATIC
SCHEMATIC
SCHEMATIC
COIL B Energized)
9 SCHEMATIC
B 9 B SCHEMATIC
m

(CoilCOIL BEnergized)
AB9Last
(Coil 9
9 AEnergized)
A(Coil
Last COIL B COIL B9A Last
(Coil (Coil9A(Coil
Last COIL B COILCOIL 9
9 SCHEMATIC
1
Last Energized) 1 1 1 AEnergized)
1
Last1Energized) 1
(Coil A Last
1 1
(CoilEnergized)
A(Coil
Last Energized)
8
(Bottom(Bottom
View)(Bottom
8
View) View)
8 2 2 2 8
(Bottom(Bottom
View)(Bottom
8
View) View)
8 2 2 2 8 (Bottom 8 A2 Last
8 (Bottom
View)
Energized)
2 2
View) View)
(Bottom

7 7 7 3 3 3 7 7 7 3 3 3 7 7 7 3 3 3
co

6 6 6 6 6 6 6 6 6 5
4 5 54 4 5 4 5 54 4 5 4 5 4 4
5

420 420420
COIL ACOILCOIL
A A 420D420D COIL ACOILCOIL
420D A A 420DD
420DDCOIL ACOILCOIL
420DD A A
SCHEMATIC SCHEMATIC
e

SCHEMATIC
SCHEMATIC SCHEMATIC
SCHEMATIC
(Coil
(Coil A Last (Coil
A LastA Energized)
Energized)Last Energized) ER420 (Coil
(Coil A Last (Coil ER420D
A LastA Energized)
Energized)Last Energized) ER420DDSCHEMATIC
SCHEMATIC
SCHEMATIC
View)(Bottom
(Bottom (Bottom View)View) View)(Bottom
(Bottom (Bottom View)View) (Coil
(Coil A Last (Coil
A LastA Energized)
Energized)Last Energized)
lin

View)(Bottom
(Bottom (Bottom View)View)
B9 B 9 1 9
COIL BCOILCOIL 1
COIL BCOILCOIL
B9 B 9 1 9 1
B9 B 9 19
COIL BCOILCOIL 1
1 1 1
8 421 8 2421
8 421 2 2 8 421D
8 2 421D
8421D 2 2 8 421DD
Schematics Shown with 8 2 421DD
8 421DD
Coil A 2Last2 Energized
7 7 7 3 3 3 7 7 7 3 3 3 Schematics
7 as
7 viewed
7 3 3 from
3 terminals
6 6 6 6 6 6 6 6 6
on

5 45 54 4 5 45 54 4 5 45 45 4

422 422422 422D 422D 422D 422DD

422DD
422DD
422H COIL ACOILCOIL A A COIL ACOILCOIL A A COIL ACOILCOIL
A A
422H 422H COIL B B COIL
COIL COIL B B 9 B COIL
COIL COIL B B
9 9 COIL B
COIL B 9 9 9 9 9
422K9SCHEMATIC
SCHEMATIC 422K 422K1 1
1SCHEMATIC SCHEMATIC SCHEMATIC
1SCHEMATIC
1 1 1 1 1
8(Coil A Last 722
8Last
Energized)
8(Coil722
A(Coil AEnergized) 8(Coil A 8Last 8LastAEnergized)
(CoilEnergized)
A(Coil 8 SCHEMATIC
8 SCHEMATIC
8 SCHEMATIC
722 Last Energized)
2 2(Bottom
Last Energized)
2 2 (Bottom (Coil A Last 2AEnergized)
(CoilEnergized)
A(Coil
Last 2 2
COIL B COILCOIL
(Bottom(Bottom
B7 B 47
View) View) 7 2 View)
4 4
(Bottom(Bottom
View) View)
B 7B
COIL B COILCOIL 7
4
7 2 View)
4 COIL BCOILCOIL
B B(Bottom
7 7Last
7View)(Bottom
4
Energized)
4
4View) View)
4 (Bottom
6 10 6 6 10
A COIL
COIL COIL A A6 6
10 10
6
106
10 10 6 106
10
9 9 19 1 1 9 19
9 1 1 COIL COILA COIL
A A 9 9
19 1 1 A COIL
COIL COIL A A
8 8 8 2 2 2 8 8 8 2 2 2 8 8 8 2 2 2
7SCHEMATIC ER421
7 SCHEMATIC
7SCHEMATIC
3 3 3 7 SCHEMATIC ER421D
7 SCHEMATIC
7 SCHEMATIC 3 3 3 7 ER421DD 7 7 3 3 3
(Coil A Last (Coil A Last Energized)
Energized) (Coil A (Coil A Last Energized) SCHEMATIC SCHEMATIC SCHEMATIC
6 (Coil6A Last6 Energized) 6 A Last 6Energized)
(Coil 6 Energized)
Last 6 A Last Energized)
422 (Bottom 422D 422D 4 4View) (Coil6Energized)
6 A Last
422DD 4(Coil
A422DD
5 42254225
(Bottom 4 (Bottom
View) View) 4
4 View) (Bottom
5
4
View)
(Bottom
5
(Bottom
422D
View)
5
(Coil 4 4
422DD
Last Energized)
5
5 (Bottom
(Bottom View)5 (Bottom
View) View)
422H422H422H
422K422K COIL ACOILCOIL
422K A A COIL ACOILCOIL
A A COIL ACOILCOIL
A A
722 722722
COIL BCOIL B BSCHEMATIC
COIL
SCHEMATICSCHEMATIC COIL BCOILCOIL SCHEMATIC
BSCHEMATIC
B SCHEMATIC COIL BCOILCOIL
B B
(Coil
A LastA Energized)
Last Energized) (Coil
420D
A LastA Energized)
Last Energized) SCHEMATIC
SCHEMATIC
SCHEMATIC 420DD
(Coil A420
(Coil
Last
(Bottom
42010420
Energized)
10(Bottom
View)(Bottom 10View)
View)
(Coil A 420D
(Coil
Last
(Bottom
Energized)
420D
10 (Bottom
10
View) 10 View)
(Bottom
View)
420DD
(Coil
(Coil A Last
420DD
10Energized)
(Coil10
A LastA Energized)
Last10
Energized)
9 9 19 1 9 9 19 1 1 9(Bottom9(Bottom
View)9(Bottom
1 1View)1
View)
1
8 8 8 2 2 2 8 8 8 2 2 2 8 8 8 2 2 2
7 7 7 3 3 3 7 7 7 3 3 3 7 7 7 3 3 3
COIL BCOIL6BCOIL
9 B9 9
1
COIL
COIL BCOIL B 9 B9 9
1 COIL BCOIL BCOIL
9 B 9 9
1
6 61 1 6 6 16 1 6 6 16 1
4 4 4 48
8 58
4
85 2 5 4
2 2 8 85 85 2 5 24 2 8 58
4
5 2 5 24 2

7 7 7 3 3 3 7 7 3 7 3 3 7 7 7 3 3 3
COIL ACOILCOIL
6
A A 6 COIL ACOILCOIL
A A 6 COIL ACOILCOIL
A A
6 6 6 6 6 6
5 45 45 4 5 45 45 4 5 45 45 4

SCHEMATIC
SCHEMATIC
ER422 SCHEMATIC
SCHEMATIC
ER422D ER422DD
SCHEMATIC SCHEMATIC
(Coil A Last
(CoilEnergized)
A(Coil
LastAEnergized)
Last Energized) COIL A (Coil A Last
(CoilEnergized)
A(Coil
LastAEnergized)
LastCOIL COIL A
ACOIL A
Energized) SCHEMATIC
SCHEMATIC
SCHEMATIC COIL A
COIL ACOIL A
(Bottom(Bottom
COIL ACOIL A
View)(Bottom
View) View) (Bottom(Bottom
View)(Bottom
View) View) (Coil A Last
(CoilEnergized)
A(Coil
LastAEnergized)
Last Energized)
(Bottom(Bottom
View)(Bottom
View) View)
SCHEMATIC
SCHEMATIC
SCHEMATIC SCHEMATIC
SCHEMATIC
SCHEMATIC
(Coil A Last A (Coil A Last Energized)
(CoilEnergized)
Last Energized) (Coil A Last A (Coil A Last Energized)
(CoilEnergized)
Last Energized) SCHEMATIC
SCHEMATIC
SCHEMATIC
View) (Bottom
(Bottom(Bottom View) View) View) (Bottom
(Bottom(Bottom View) View) (Coil A Last A (Coil A Last Energized)
(CoilEnergized)
Last Energized)
View) (Bottom
(Bottom(Bottom View) View)

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 21

 MILITARY QUALIFIED (JAN) RELAYS

Series J114 Electromechanical Relays

The Series J114 Centigrid® relay is an ultraminiature, hermetically sealed, armature relay. Its low profile • All welded construction
height .275” (7 mm) and .100” (2.54 mm) grid spaced terminals, which precludes the need for spreader pads, • Unique uni-frame design providing high
make it ideal for applications where extreme packaging density and/or close PC board spacing are required. magnetic efficiency and mechanical rigidity
The basic design and internal construction are similar to the standard Teledyne DPDT TO-5 relay (e.g., • High force/mass ratio for resistance to shock
Series J412). and vibration
The Series J114D and J114DD relays have internal discrete silicon diodes for coil suppression and polarity • Precious metal alloy contact material with
reversal protection. gold plating assures excellent high current
By virtue of its inherently low intercontact capacitance and contact circuit losses, the J114 relay has proven and dry circuit switching capabilities
to be an excellent ultraminiature RF switch for frequency ranges well into the UHF spectrum. A typical
RF application for the J114 relay is in handheld radio transceivers, wherein the combined features of good
RF performance, small size, low coil power dissipation and high reliability make it a preferred method of
Transmit-Receive switching.

Relay Type Nominal Coil

  DPDT Non-Latching Part No. Voltage Resistance P.U.V D.O.V (Vdc) Contact Load Rating

m
Diode Options (Vdc) (Ω) (Vdc) (max.) min. max.

  D = Internal diode for coil 5 50 3.5 0.14 2.3   Resistive: 1A/28Vdc

co
  transient suppression J114 6 98 4.5 0.18 3.2   Inductive: 200mA/28Vdc (320mH)
(M39016/17)
  DD = Internal diode for coil 9 220 6.8 0.35 4.9   Lamp: 100mA/28Vdc
  transient suppression and 12 390 9.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV

s.
J114D
  polarity reversal protection (M39016/18) 18 880 13.5 0.59 10.0
Vibration Shock 26 1560 18.0 0.89 13.0
nt
30 g’s 75 g’s 6 msec, 5 39 4.0 0.6 2.8   Resistive: 1A/28Vdc

to 3000 Hz half-sine 6 78 5.0 0.7 3.4   Inductive: 200mA/28Vdc (320mH)

ne

J114DD 9 220 7.8 0.8 5.3   Lamp: 100mA/28Vdc

Acceleration Temperature
(M39016/18) 12 390 10.0 0.9 6.5   Low Level: 10 to 50 uA/10 to 50 mV
Operating &
Storage: 18 880 14.5 1.1 10.0
po

50 g’s
–65°C to +125°C 26 1560 19.0 1.4 13.0

Series J116C Electromechanical Relays

m

The J116C Centigrid® relay is an ultraminiature, hermetically sealed, armature relay capable of being directly • All welded construction
driven by most IC logic families. Its low profile height and .100” (2.54 mm) grid spaced terminals, which • Unique uni-frame design providing high
co

preclude the need for spreader pads, make it ideal for applications where extreme packaging density and/or magnetic efficiency and mechanical rigidity
close PC board spacing are required. • High force/mass ratio for resistance to shock
The Series J116C utilizes an internal silicon diode for coil suppression, a Zener diode to protect the MOSFET and vibration
gate input, and an N-channel enhancement mode MOSFET chip, which enables direct relay interfacing with
e
M I L I TA RY Q UA L I F I E D ( JA N )

most Microprocessor and IC logic families (CMOS, TTL and MOS).

lin

Relay Type 114,Nominal

134 Coil
114D, 134D
on

S114/S134
  DPDT Non-Latching Coil Current S114D/S134D
Part No. Voltage 172
Operating P.U.V Contact Load Rating
(mA) (Vdc)
172D
CMOS Feature (Vdc) Power (mW) (max.)
Min. Max.
  Internal power MOSFET 8
5 7
96.5 1
132.3 641 4.0   Resistive:
8
7 11A/28Vdc
  driver, Zener diode gate protec- 6 2
6 60.3 83.9 462 4.9   Inductive:
6 200mA/28Vdc
2 (320mH)
  tion, and diode coil suppression 4
J116C 9 33.1
5 347.1 368 7.3   Lamp:
5 100mA/28Vdc
3
Vibration Shock (M28776/6)
4
12 24.9 36.1 369 9.8   Low Level: 10 to 50 uA/10 to 50 mV
30 g’s 75 g’s 6 msec, 18 SCHEMATIC
16.1 SCHEMATIC
114, 134 114, 134 (Bottom View)24.1 368 14.6
(Bottom View)
to 3000 Hz half-sine
S114/S134 S114/S134 114D, 134D 114D, 134D
26 12.9 19.9 450 19.5 116C, 136C
172 172 S114D/S134D S114D/S134D
114DD, 134DD
Acceleration Temperature 172D 172D
S114DD/S134DD

Operating & – 10 +1
9
50 g’s Storage:
7 1 7 1 7
8 88
8 1 77 11
6 2 8
–65°C to +125°C 6 2
6 2
8 2
66 2
2 PIN 1: + SUPPLY
4 7 3 PIN 9: – SUPPLY
5 3 4
5 3 5 3 5 3 PIN 10: GATE
4 5 4 3 4
4 6
P.U.V = Pick-Up Voltage
D.O.V = Drop-Out Voltage SCHEMATIC
(Bottom View) SCHEMATIC
J114
SCHEMATIC
J114D
(Bottom View)
SCHEMATIC
J114DD
SCHEMATIC
(Bottom View) J116C
SCHEMATIC
(Bottom View) (Bottom View) (Bottom View)
114DD, 134DD
Schematics as viewed from terminals S114DD/S134DD 114DD, 134DD
116C, 136C
S114DD/S134DD
122C
8
7 1
Page 22 (800) 284-7007 • www.teledynerelays.com • +447 (0)98–123610453124
+ 1 • www.teledyne-europe.com 10 +
© 2010 TELEDYNE RELAYS
1 9 1
6 2
6 8 2 2
5 3 8 2 PIN 4: GATE A
4 PIN 1: + SUPPLY PIN 5: – SUPPLY
 MILITARY QUALIFIED (JAN) RELAYS

Series J134 Electromechanical Relays

The J134 sensitive Centigrid® relay retains the same features as the J114 standard Centigrid® relay with • All welded construction
only a minimal increase in profile height .375” (9.53 mm). Its .100” (2.54 mm) grid spaced terminals, which • Unique uni-frame design providing high
preclude the need for spreader pads, and its low profile make the J134 relay ideal for applications where high magnetic efficiency and mechanical rigidity
• High force/mass ratio for resistance to shock
packaging density is important. and vibration
The Series J134D and J134DD have internal discrete silicon diodes for coil suppression and polarity reversal • Precious metal alloy contact material with
protection. gold plating assures excellent high current
and dry circuit switching capabilities
The sensitive J134 Centigrid® relay has a high resistance coil, thus requiring extremely low operating power
(200 mw typical). The advantages of reduced heat dissipation and power supply demands are a plus.

Relay Type Nominal Coil

  DPDT Non-Latching Part No. Voltage Resistance P.U.V D.O.V (Vdc) Contact Load Rating
Diode Options (Vdc) (Ω) (Vdc) (max.) min. max.

m
  D = Internal diode for coil 5 100 3.5 0.12 2.5   Resistive: 1A/28Vdc
  transient suppression J134 6 200 4.5 0.18 3.2   Inductive: 200mA/28Vdc (320mH)

co
  DD = Internal diode for coil (M39016/41) 9 400 6.8 0.35 4.9   Lamp: 100mA/28Vdc
  transient suppression and 12 800 9.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV
J134D
  polarity reversal protection (M39016/42) 18 1600 13.5 0.59 10.0

s.
Vibration Shock 26 3200 18.0 0.89 13.0

30 g’s 75 g’s 6 msec, 5 64 3.7 0.7 2.6   Resistive: 1A/28Vdc

nt
to 3000 Hz half-sine 6 125 4.8 0.8 3.0   Inductive: 200mA/28Vdc (320mH)
J134DD 9 400 8.0 0.9 4.5   Lamp: 100mA/28Vdc
Acceleration Temperature
(M39016/43)
ne

12 800 11.0 1.0 5.8   Low Level: 10 to 50 uA/10 to 50 mV

Operating &
Storage: 18 1600 14.5 1.1 9.0
50 g’s
–65°C to +125°C 26 3200 19.0 1.3 13.0
po

Series J136C Electromechanical Relays

m

The sensitive J136C Centigrid® relay is an ultraminiature, hermetically sealed, armature relay capable • All welded construction
of being directly driven by most IC logic families. Its low profile height and .100” (2.54 mm) grid spaced • Unique uni-frame design providing high
co

terminals, which precludes the need for spreader pads, make it ideal for applications where extreme magnetic efficiency and mechanical rigidity
packaging density and/or close PC board spacing are required. • High force/mass ratio for resistance to shock
The sensitive J136C Centigrid® relay has a high resistance coil, thus requiring extremely low operating and vibration
power (200 mW, typical). The advantages of reduced heat dissipation and power supply demands are a • Precious metal alloy contact material with
e

plus. gold plating assures excellent high current

The sensitive Series J136C utilizes an internal silicon diode for coil suppression, a Zener diode to protect
lin

and dry circuit switching capabilities

the MOSFET gate input, and an N-channel enhancement-mode MOSFET chip that enables direct relay
interfacing with most microprocessor and IC logic families (CMOS, TTL and MOS).
114, 134
114D, 134D
on

Relay Type Nominal

S114/S134 Coil
172 S114D/S134D
  DPDT Non-Latching Coil Current 172D
Part No. Voltage Operating P.U.V Contact Load Rating
(mA) (Vdc)
CMOS Feature (Vdc) Power (mW) (max.)
Min.
7 1
Max. 8
  Internal power MOSFET 6
8
2
7 1
5 43.0 56.0 250 4.0   Resistive: 1A/28Vdc
  driver, Zener diode gate protec- 6 2
6 27.0
5 4 3 33.0 180 4.9   Inductive: 200mA/28Vdc (320mH)
  tion, and diode coil suppression 5
4 3
J136C 9 17.8 26.4 203 7.3   Lamp: 100mA/28Vdc
Vibration Shock (M28776/7) 12 11.3
SCHEMATIC 17.7 180 9.8   Low Level: 10 to 50 uA/10 to 50 mV
SCHEMATIC
30 g’s 75114,
g’s134
6 msec, 114, 134 (Bottom View) (Bottom View)
S114/S134 S114/S134 18 114D, 134D
8.4 13.8 114D, 134D 14.6
203
S114D/S134D S114D/S134D 116C, 136C
to 3000 Hz half-sine
172 172 26
114DD, 134DD
172D 5.8 10.2 219
172D
19.5
S114DD/S134DD
Acceleration Temperature
Operating & 9
– 10 +1
7 1 8 88
Storage: 7 1 7 1 77
50 g’s 6
8
2 8
11
6 2 8 2
–65°C to +125°C 6 2
66 2
2 PIN 1: + SUPPLY
4 7 3 PIN 9: – SUPPLY
5 3 4
5 3 5 3 5 3 PIN 10: GATE
4 5 4 3 4
4 6

SCHEMATIC SCHEMATIC SCHEMATIC

Schematics as viewed from terminals
(Bottom View) SCHEMATIC
J134 J134D
(Bottom View) J134DD
SCHEMATIC
(Bottom View) J136C
SCHEMATIC
(Bottom View) (Bottom View) (Bottom View)
114DD, 134DD
S114DD/S134DD 114DD, 134DD P.U.V = Pick-Up Voltage
116C, 136C
S114DD/S134DD D.O.V = Drop-Out Voltage
122C
8
7 1
© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT
7 9
8– TO CHANGE
10 +1 WITHOUT NOTICE 10 +
Page 23
1 9 1
6 2
6 8 2 2
5 3 8 2 PIN 4: GATE A
4 PIN 1: + SUPPLY PIN 5: – SUPPLY
 MILITARY QUALIFIED (JAN) RELAYS

Series J411 & J431 Electromechanical Relays

The TO-5 relay, originally conceived and developed by Teledyne, has become one of the industry • All welded construction
standards for low-level switching from dry circuit to 1 ampere. Designed specifically for high-density PC • Unique uni-frame design providing high
board mounting, its small size and low coil power dissipation make the J411 relay one of the most versatile magnetic efficiency and mechanical rigidity
ultraminiature relays available. • High force/mass ratio for resistance to shock
The Series J411D and J411DD relays have internal discrete silicon diodes for coil suppression and polarity and vibration
reversal protection. The hybrid J411T relay features an internal silicon suppression diode and transistor • Precious metal alloy contact material with
driver. This hybrid package reduces required PC board floor space by reducing the number of external gold plating assures excellent high current
components needed to drive the relay. and dry circuit switching capabilities
The sensitive J431 relay has a high resistance coil, thus requiring extremely low operating power (150 mw
typical). The advantages of reduced heat dissipation and power supply demands are a plus.
The Series J431D and J431DD relays have internal discrete silicon diodes for coil suppression and polarity
reversal protection. The hybrid J431T relay features an internal silicon suppression diode and transistor
driver. This hybrid package reduces required PC board floor space by reducing the number of external
components needed to drive the relay.

Relay Type Nominal Coil

m
  SPDT Non-Latching Part No. Voltage Resistance P.U.V D.O.V (Vdc) Contact Load Rating
(Vdc) (Ω) (Vdc) (max.)

co
Coil Type min. max.

  J411 = Standard Coil 5 63 3.7 0.15 2.4   Resistive: 1A/28Vdc

  J431 = Sensitive Coil J411 6 125 4.5 0.18 2.8   Inductive: 200mA/28Vdc (320mH)

s.
(M39016/7)
Diode Options 9 280 6.8 0.35 4.2   Lamp: 100mA/28Vdc
  D = Internal diode for coil J411D 12 500 9.0 0.40 5.6   Low Level: 10 to 50 uA/10 to 50 mV
nt
  transient suppression
(M39016/23) 18 1130 13.5 0.58 8.4
  DD = Internal diode for coil 26 2000 18.0 0.89 10.4
ne

  transient suppression and 5 50 4.5 0.15 2.4   Resistive: 1A/28Vdc

  polarity reversal protection 6 98 5.5 0.18 2.8   Inductive: 200mA/28Vdc (320mH)

J411DD 9 280 7.8 0.35 4.2   Lamp: 100mA/28Vdc
  T = Internal transistor drive
po

(M39016/24) 12 500 10.0 0.40 5.6   Low Level: 10 to 50 uA/10 to 50 mV

  and coil transient suppression
18 1130 14.5 0.58 8.4
  diode
26 2000 19.0 0.89 10.4
Vibration Shock
m

5 63 3.9 0.15 2.4   Resistive: 1A/28Vdc

30 g’s 75 g’s 6 msec,
6 125 5.2 0.18 2.8   Inductive: 200mA/28Vdc (320mH)
to 3000 Hz half-sine
co

J411T 9 280 7.8 0.35 4.2   Lamp: 100mA/28Vdc

Acceleration Temperature (M28776/5) 12 500 10.0 0.40 5.6   Low Level: 10 to 50 uA/10 to 50 mV
18 1130 14.5 0.58 8.4
Operating &
e
M I L I TA RY Q UA L I F I E D ( JA N )

50 g’s Storage: 26 2000 19.0 0.89 10.4

lin

–65°C to +125°C 5 125 3.7 0.15 2.0   Resistive: 1A/28Vdc

411/431 411D/431D 411DD/431DD 411T/431T
J431 6 255 4.5 0.18 2.8   Inductive: 200mA/28Vdc (320mH)
(M39016/10)
9 630 6.8 0.35 4.2   Lamp: 100mA/28Vdc
on

4 1 4 4
J431D
5
12 9 1025 1 9.0 0.41 5.6   Low Level: 10 to 50 uA/10 to 50 mV
5 5 1 1 2
J411 (M39016/25) 18 8
23003 13.5 0.58 8.4
3 2 J431 7
3 2 3 2 26 6 4000 4 18.0 0.89 10.4
1 411D/431D 411DD/431DD 411T/431T 5 100 4.5 0.15 2.4   Resistive: 1A/28Vdc
SCHEMATIC SCHEMATIC SCHEMATIC
(Bottom View) (Bottom View) (Bottom View) 6 200
SCHEMATIC 5.5 0.18 2.8   Inductive: 200mA/28Vdc (320mH)
(Bottom View)
4 4 J431DD
9 1 9 630 7.8 0.35 4.2   Lamp: 100mA/28Vdc
1 5 1 2
5 J411D (M39016/26)
8 12 1025 10.0 0.40 5.6   Low Level: 10 to 50 uA/10 to 50 mV
3
2
J431D 7
18 2300 14.5 0.58 8.4
3 2 3 2 6 4
1D 411DD/431DD 411T/431T 26 4000 19.0 0.89 10.4
C SCHEMATIC SCHEMATIC 5 125 3.6 0.15 2.0   Resistive: 1A/28Vdc
(Bottom View) (Bottom View) SCHEMATIC
412/432 412D/432D 412DD/432DD
(Bottom View)
6 412T/432T 4.8
255 0.18 2.8   Inductive: 200mA/28Vdc (320mH)
4
5
412H/432H 9 412DV/432DV
1 412DDV 712TN/732TN
1
412K 8 712D/732D
2
J431T 9 630 7.8 0.35 4.2   Lamp: 100mA/28Vdc
J411DD
412V 7 3 (M28776/4) 12 1025 10.0 0.41 5.6   Low Level: 10 to 50 uA/10 to 50 mV
3 2
J431DD
712/732 6 4
DD 411T/431T
18 2300 14.5 0.58 8.4
SCHEMATIC 26 4000 19.0 0.89 10.4
(Bottom View) SCHEMATIC
/432 9 412D/432D
1 9
412DD/432DD
(Bottom
1 View) 412T/432T 10
1 1
H/432H 98 412DV/432DV
2 8 412DDV 9 712TN/732TN
2P.U.V = Pick-Up Voltage
9
1 Schematics as viewed from terminals
2 28 2
K 8 7 712D/732D3
8
3 J411T
7 D.O.V = Drop-Out
3
Voltage 7 3
V 7 6 4 4
7 3
/732 6 4
J431T
6
6 4 6 4

SCHEMATIC SCHEMATIC SCHEMATIC SCHEMATIC

SCHEMATIC
(Bottom View) (Bottom View) (Bottom View) (Bottom View)
432D
1 Page 24 412DD/432DD
(Bottom View)
1
(800) 284-7007 • www.teledynerelays.com
412T/432T 10 • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
9
V/432DV
2 412DDV2 9 1
712TN/732TN 9
8 1
732D 8 2 8 2
3 3
7 3
7 3 7
 MILITARY QUALIFIED (JAN) RELAYS

Series J412 & J432 Electromechanical Relays

The TO-5 relay, originally conceived and developed by Teledyne, has become one of the industry • All welded construction
standards for low-level switching from dry circuit to 1 ampere. Designed specifically for high-density PC • Unique uni-frame design providing high
board mounting, its small size and low coil power dissipation make the J412 relay one of the most versatile magnetic efficiency and mechanical rigidity
ultraminiature relays available. • High force/mass ratio for resistance to shock
The Series J412D and J412DD relays have internal discrete silicon diodes for coil suppression and polarity and vibration
reversal protection. The hybrid J412T relay features an internal silicon suppression diode and transistor • Precious metal alloy contact material with
driver. This hybrid package reduces required PC board floor space by reducing the number of external gold plating assures excellent high current
components needed to drive the relay. and dry circuit switching capabilities
The sensitive J432 relay has a high resistance coil, thus requiring extremely low operating power (200 mw
typical). The advantages of reduced heat dissipation and power supply demands are a plus.
The Series J432D and J432DD relays have internal discrete silicon diodes for coil suppression and polarity
reversal protection. The hybrid J432T relay features an internal silicon suppression diode and transistor
driver. This hybrid package reduces required PC board floor space by reducing the number of external
components needed to drive the relay.

Relay Type Nominal Coil

m
  DPDT Non-Latching Part No. Voltage Resistance P.U.V D.O.V (Vdc) Contact Load Rating
(Vdc) (Ω) (Vdc) (max.)

co
Coil Type min. max.

  J412 = Standard Coil 5 50 3.5 0.14 2.3   Resistive: 1A/28Vdc

  J432 = Sensitive Coil J412 6 98 4.5 0.18 3.2   Inductive: 200mA/28Vdc (320mH)

s.
(M39016/9)
Diode Options 9 220 6.8 0.35 4.9   Lamp: 100mA/28Vdc
  411/431
D = Internal diode for coil
411D/431D J412D
411DD/431DD 12 390
411T/431T 9.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 uA
nt
  transient suppression
(M39016/15) 18 880 13.5 0.59 10.0
  DD =1 Internal diode for coil 26 1560 18.0 0.89 13.0
4 4 4 9 1
ne

5
  transient suppression and
5 1 5 1 5 8
39 2 3.9 0.6 2.8   Resistive: 1A/28Vdc
6 7 78
3 5.2 0.7 3.4   Inductive: 200mA/28Vdc (320mH)
3  polarity
2 reversal protection
3 2 3 2 6 4
1/431 411DD/431DD J412DD 9 220 7.8 0.8 5.3   Lamp: 100mA/28Vdc
  T411D/431D
= Internal transistor drive 411T/431T
po

(M39016/20) 12 390 10.0 0.9 6.5   Low Level: 10 to 50 uA/10 to 50 uA

SCHEMATIC SCHEMATIC
  and coil transient suppression SCHEMATIC
(Bottom View) (Bottom View) (Bottom View) SCHEMATIC
18 880 14.5 1.1 10.0
1   4 diode 4 9 1
(Bottom View)

5 1 5 1
8
2 26 1560 19.0 1.4 13.0
Vibration Shock
m

7 3 5 50 3.5 0.14 2.3   Resistive: 1A/28Vdc

2 3 30 g’s
2 75 g’s 36 msec,2 6 4
431D 411DD/431DD
6 98 4.5 0.18 3.2   Inductive: 200mA/28Vdc (320mH)
to 3000 Hz 411T/431T
half-sine
co

ATIC SCHEMATIC SCHEMATIC J412T 9 220 6.8 0.35 4.9   Lamp: 100mA/28Vdc
View) Acceleration
(Bottom View) Temperature
(Bottom View) SCHEMATIC
(M28776/1) 12 390 9.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV
412/432 412D/432D
1 412DD/432DD (Bottom View)
412T/432T
4 9
1 5 412H/432H
1 412DV/432DV
Operating
8 & 2 412DDV 18 880
712TN/732TN 13.5 0.59 10.0
e

412K 712D/732D
Storage:
50 g’s 7 3 26 1560 18.0 0.89 13.0
2 3 412V2
–65°C to6 +125°C4
lin

712/732 5 100 3.5 0.14 2.5   Resistive: 1A/28Vdc

CD 411T/431T
SCHEMATIC J432 6 200 4.5 0.18 3.2   Inductive: 200mA/28Vdc (320mH)
) (Bottom View) SCHEMATIC (M39016/11)
412/432 9
412D/432D
1
412DD/432DD
(Bottom View) 412T/432T 9 400
10
6.8 0.35 4.9   Lamp: 100mA/28Vdc
on

9 1
412H/432H 412DV/432DV 412DDV 1 712TN/732TN12 9850 9.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV
8 1 2 8 J412 2
9 J432D 1
412K 9 712D/732D 8 2 8 2
8 7 2 3 J432 3
(M39016/16) 18 1600 13.5 0.59 10.0
412V 7
7 3 7 3
6 3 4 4
712/732 7 6
6 4 26 63300 4 18.0 0.89 13.0
6 4
5 64 3.7 0.7 2.6   Resistive: 1A/28Vdc
SCHEMATIC SCHEMATIC SCHEMATIC 6 SCHEMATIC
125 4.8 0.8 3.0   Inductive: 200mA/28Vdc (320mH)
D/432D
1 412DD/432DD
SCHEMATIC
(Bottom View) 412T/432T
(Bottom View) (Bottom View) 10
(Bottom View)
9 1
DV/432DV
2 412DDV
(Bottom View)
2
9 712TN/732TN
1
J432DD
9 9 400 8.0 0.9 4.5   Lamp: 100mA/28Vdc
8
D/732D 3 J412D
8 2 1
(M39016/21)
8 2
3 12 850 11.0 1.0 5.8   Low Level: 10 to 50 uA/10 to 50 mV
4
7 J432D
7 3 7 3
4
6
6 4 6 4 18 1600 14.5 1.1 9.0
26 3300 19.0 1.3 13.0
EMATIC SCHEMATIC SCHEMATIC SCHEMATIC
om View) (Bottom View) (Bottom View) (Bottom View) 5 100 3.6 0.14 2.5   Resistive: 1A/28Vdc
10
1
2DD 1
412T/432T
9 9 6 200 4.8 0.18 3.2   Inductive: 200mA/28Vdc (320mH)
2 1
2
3
8 712TN/732TN J412DD
8 2
J432T 9 400 7.8 0.35 4.9   Lamp: 100mA/28Vdc
7 3
4
7 3 J432DD (M28776/3) 12 850 11.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV
6 4 6 4
18 1600 14.5 0.59 10.0
ATIC SCHEMATIC SCHEMATIC 26 3300 19.0 0.89 13.0
View) (Bottom View) (Bottom View)

10
9
J412T Schematics as viewed from terminals P.U.V = Pick-Up Voltage
2 1
8 2
J432T D.O.V = Drop-Out Voltage
3 7 3
6 4

SCHEMATIC
© 2010 TELEDYNE
(Bottom View) RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 25
 MILITARY QUALIFIED (JAN) RELAYS

Series J255 Electromechanical Relays

The Series J255 is an industry-standard, half-size, latching crystal can relay. It has a wide range of switching • All welded construction
capabilities ranging from low level to 2 amps. The Series J255 latching relay configuration is double-pole • Wire leads, gold-plated or solder-coated
double-throw (DPDT), so the relay offers excellent switching density and versatility. • Matched seal for superior hermeticity
Half-Size Crystal Can Features: • Gold-plated contact assembly
  • Low level to 2 amps • Modernized assembly process
  • Wide range of switching capabilities • Advanced cleaning techniques
  • Smallest relay package capable of switching 2 amps
  • Modernized assembly process
  • Qualified to MIL-PRF39016/45
  • Lead-free (gold-plated wire lead only)

Relay Type Nominal Coil

  DPDT Magnetic-Latching Set & Reset Voltage
Part No. Voltage Resistance Contact Load Rating
(Vdc)
Vibration (Vdc) (Ω)
Min. Max.

m
  30G, 10-2500 Hz
5 45 1.0 3.8   Resistive: 2A/28Vdc
  (Sinusoidal)
6 63 1.3 4.5   Inductive: 0.75A/28Vdc (320mH)
Shock

co
J255 12 254 2.6 9.0   Intermediate Current: 0.1A/28Vdc
(M39016/45)
  100G, 6 msec half-sine
26 1000 5.2 18.0   Lamp: 0.16A/28Vdc
  (Specified Pulse)
  Low Level: 10 to 50 uA/10 to 50 mV

s.
Temperature
J255
J255 256
  Operating & Storage: B3 A2 A1 A3
B2 Y1 B1
nt
  –65°C to +125°C
X1
Y2 X2
X2
Y2
Y1
A1 X1 A2 B3
B2 A3
ne
B1

SCHEMATIC SCHEMATIC
(Coil X Last Energized) (Coil X Last Energized)
(Bottom View) (Bottom View)

Series J421 Electromechanical Relays

po

The magnetic-latching TO-5 relay, originally conceived 257

and developed by Teledyne, 258
has become one of • All welded construction
the industry standards for low-level switching from dry circuit to 1 ampere. Designed for high-density PC
A3 • Unique uni-frame design providing high
B3 A2 A1

board mounting, its small size and low coil power dissipation make the J421 relay one of the most versatile
X1
B2 X2 B1

magnetic efficiency and mechanical rigidity

m

Y2 X2

ultraminiature relays available. Y1

Y2 Y1
• High force/mass ratio for resistance to shock
The Series J421D and J421DD utilize discrete silicon diodes for coil suppression and polarity reversal
A1 X1 A2 B3
B1 B2 A3 and vibration
protection. • Precious metal alloy contact material with
co

SCHEMATIC SCHEMATIC
The Series J421 magnetic-latching relays are ideally suited
(Coil X Last Energized)
(Bottom View) for applications(Bottom where
(Coil Y Last Energized)
View) coil power dissipation gold plating assures excellent high current
must be minimized. The relays can be operated with a short duration pulse. After the contacts have and dry circuit switching capabilities
transferred, no external holding power is required. The magnetic-latching feature of the Series J421 provides
e
M I L I TA RY Q UA L I F I E D ( JA N )

a “memory” capability, since the relays will not reset upon removal of coil power.
lin

Relay Type Nominal Coil

  SPDT Magnetic-Latching Part No. Voltage Resistance Set & Reset Contact Load Rating
(Ω)
on

(Vdc) Voltage (Vdc)

Diode Options
5 61 3.5   Resistive: 1A/28Vdc
  D = Internal diode for coil
6 120 4.5   Inductive: 200mA/28Vdc (320mH)
  transient suppression
J421 9 280 6.8   Lamp: 100mA/28Vdc
  DD = Internal diode for coil (M39016/8) 12 500 9.0   Low Level: 10 to 50 uA/10 to 50 mV
  transient suppression and 18 1130 13.5
  polarity reversal protection 26 2000 18.0
Vibration Shock 5 61 3.7   Resistive: 1A/28Vdc
30 g’s 100 g’s 6 msec, 6 120 4.5   Inductive: 200mA/28Vdc (320mH)
to 3000 Hz half-sine J421D 9 280 6.8   Lamp: 100mA/28Vdc
Acceleration Temperature (M39016/27) 12 500 9.0   Low Level: 10 to 50 uA/10 to 50 mV
Operating & 18 1130 13.5
50 g’s Storage: 26 2000 18.0
–65°C to +125°C 5 48 4.5   Resistive: 1A/28Vdc
6 97 5.5   Inductive: 200mA/28Vdc (320mH)
J421DD 9 280 7.8   Lamp: 100mA/28Vdc
*See Schematics on Page 27
(M39016/28) 12 500 10.0   Low Level: 10 to 50 uA/10 to 50 mV
18 1130 14.5
26 2000 19.0

Page 26 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 MILITARY QUALIFIED (JAN) RELAYS

Series J420 & J422 Electromechanical Relays

The magnetic-latching TO-5 relay, originally conceived and developed by Teledyne, has become one of • All welded construction
the industry standards for low-level switching from dry circuit to 1 ampere. Designed for high-density PC • Unique uni-frame design providing high
board mounting, its small size and low coil power dissipation make the J420 & J422 relays some of the most magnetic efficiency and mechanical rigidity
versatile ultraminiature relays available. • High force/mass ratio for resistance to shock
The Series J420D/J422D and J420DD/J422DD utilize discrete silicon diodes for coil suppression and polarity and vibration
reversal protection. • Precious metal alloy contact material with
The Series J420/J422 magnetic-latching relays are ideally suited for applications where coil power gold plating assures excellent high current
dissipation must be minimized. The relays can be operated with a short duration pulse. After the contacts and dry circuit switching capabilities
have transferred, no external holding power is required. The magnetic-latching feature of the Series J420/
J422 relays provide a “memory” capability, since the relays will not reset upon removal of coil power.

Relay Type Nominal Coil

  DPDT Magnetic-Latching Part No. Voltage Resistance Set & Reset Contact Load Rating
(Vdc) (Ω) Voltage (Vdc)
Grounding Options
421 421421 J420 5 61 3.5
421D
421D 421D   Resistive: 1A/28Vdc
421DD 421DD
421DD

m
  J420 = Individual
(M39016/12) 6 120 4.5   Inductive: 200mA/28Vdc (320mH)
  J422 = Common J422
9 280 6.8   Lamp: 100mA/28Vdc

co
Diode Options (M39016/12)
J420D 12 500B 9.0   Low
  D = Internal diode for coil 9 B COIL
COIL COIL
COIL
B B COIL BCOIL B 9 9 9 COIL Level:
B 10
COIL
COIL
B B to
9
50 uA/10 to 50 mV
9 9
9 9 (M39016/29) 1
1 1 1 1 1 1 1 1
18 11308 13.5
  transient suppression 8 8 8 J422D 8 8 8 8
2 2
8

s.
27 2 2 27 2 2 2
7 47 4(M39016/29)
4 26 2000 7 47 18.0
4 4 7 47 7 4 4
  DD = Internal diode for coil 4216 421
COIL
COIL
COIL A A A 6 6 421 6 421D
6 421D
6 421D 6 421DD
6 421DD
6 421DD
  transient suppression and 5 48 4.5 COIL
COIL
COIL A A A   Resistive: 1A/28Vdc A COIL
COIL COIL A A
nt
  polarity reversal protection J420DD 6 97 5.5   Inductive: 200mA/28Vdc (320mH)
SCHEMATIC
SCHEMATIC
SCHEMATIC (M39016/30) SCHEMATIC
SCHEMATIC
SCHEMATIC
(Coil
A LastA Energized)
Last Energized) 9 280(Coil A Last (Coil 7.8
A LastA Energized)
Last Energized)   Lamp:SCHEMATIC
100mA/28Vdc
SCHEMATIC
SCHEMATIC
Vibration Shock (Coil
(Coil A Last Energized)
View)(Bottom
(Bottom (Bottom View)View)
(Coil
Energized)
View)(Bottom
(Bottom (Bottom View)View) (Coil
(Coil A Last (Coil
A LastA Energized)
Energized)Last Energized)
ne

B 12 500
B COIL COIL
B COIL
B B 10.0   Low
COIL Level:
B 10
B COIL
COIL B to9 509uA/10 to 50 mV
(Bottom View)(Bottom
(Bottom View)View)
30 g’s 100 g’s 6 msec, 9 9 19
J422DD
1
COIL COIL
B COIL 9 9
1
9
1
9
1 1 1
1 1
8 8 8
(M39016/30) 18 11308 8 8
14.5 8 8 8
to 3000 Hz half-sine 7 2 2 2 7 7 2 2 2 2 2 2
47 74 4 26 2000 4 719.0
4 4 7 7
4 74 4
Acceleration Temperature
po

COIL COIL A A6
A COIL 6 6 6 6 6 6 6 6
420 420420 420D
420D 420D COIL COIL
A COIL
A A 420DD
420DD
420DD COIL COIL
A COIL
A A
Operating &
Storage: SCHEMATIC
SCHEMATIC
SCHEMATIC SCHEMATIC
SCHEMATIC
SCHEMATIC
50 g’s (Coil A Last
(CoilEnergized)
A(Coil
LastAEnergized)
Last Energized) (Coil A Last
(CoilEnergized)
A Last Energized)
(Coil A Last Energized) SCHEMATIC
SCHEMATIC
SCHEMATIC
COIL BCOILCOIL
B9 B (Bottom 9
9 (Bottom COIL B COILCOIL B 9(Bottom
B9(Bottom 9 View) COIL Last9AEnergized)
B Energized)
B 9A Last A9
m

(Bottom View)
1 View)1View)1 View)
1 (Bottom 1
1 View)
COIL B COIL
(Coil (Coil (Coil
1 Last1Energized)
1
–65°C to +125°C 8
(Bottom(Bottom
View)(Bottom
View) View)
8 2
8 8 8 2 2 2 8 8 2 2 2 8 8 2 2

7 7 7 3 3 3 7 7 7 3 3 3 7 7 7 3 3 3
co

6 6 6 6 6 6 6 6 6 5
4 5 54 4 5 4 5 54 4 5 4 5 4 4
5

420 420420 420D420D

420D 420DD
420DD
420DD
COIL ACOILCOIL
A A COIL ACOILCOIL
A A COIL ACOILCOIL
A A
SCHEMATIC
SCHEMATIC
SCHEMATIC SCHEMATIC
SCHEMATIC
SCHEMATIC
e

(Coil
(Coil A Last
J420
(Coil
A LastA Energized)
Energized)Last Energized) J420D
(Coil
(Coil A Last (Coil
A LastA Energized)
Energized)Last Energized) J420DDSCHEMATIC
SCHEMATIC
SCHEMATIC
(Bottom View) (Bottom View) (Coil
(Coil A Last (Coil
A LastA Energized)
Energized)Last Energized)
9 B (Bottom
B(Bottom
COIL BCOILCOIL View)
9 View)
B 9 (Bottom
B9 (Bottom
COIL BCOILCOIL View) View) B 9(Bottom
COIL BCOILCOIL B 9(Bottom
19 1 19 1 1 9(Bottom
1 View)
lin

1 1 View) View) 1
8 8 8 2 2 2 8 8 8 2 2 2 8 8 8 2 2 2
421
7 421
421 7 421D
7 7421D
421D 7 421DD
Schematics Shown7 with 421DD
7 3Coil 3A Last
421DD Energized
7 7 3 3 3 3 3 3 3
6 6 6 6 6 6 6 6 6
5 45 54 4 5 45 54 4 Schematics
5 4as
5 viewed
45 4 from terminals
on

422 422422COIL ACOILCOIL A A 422D

422D 422D COIL ACOILCOIL
A A 422DD
422DD
422DD COIL ACOILCOIL
A A
422H 422H 422H
SCHEMATIC
SCHEMATIC
SCHEMATIC
422K B COIL
COIL COIL B COIL
B B COIL COIL B B SCHEMATIC
9 SCHEMATIC
9 SCHEMATIC
9 B COIL
COIL COIL B B 9 9
9422K
(Coil A Last9422K
(Coil 9
Energized)
A(Coil
Last
1 AEnergized) 1
Last1 Energized) (Coil A Last
(CoilEnergized)
A(Coil
Last
1 AEnergized)
Last 1 SCHEMATIC
SCHEMATIC
9 SCHEMATIC
1 1
1 Energized) (Coil A Last
1
(CoilEnergized)
8 722
(Bottom(Bottom
View) View) View) (Bottom(Bottom
View)(Bottom
View) View) A(Coil
LastAEnergized)
Last Energized)
8 722 8 722
(Bottom
8 8 8 8 8 (Bottom8 (Bottom
COIL B COILCOIL
B7 B 7 27 2 2 COIL B COILCOIL
B 7B 2 7 2 2 COIL B(Bottom
COIL BCOIL B
View) View) View)
27 2 2
4 4 4 7
4 4 4 7 7
4 4 4
10 610 10 106 106 10 106 6 10
10
A COIL
COIL COIL A A69 6 6
19
6
9 9 9
9 19 1 1 9 9 A COIL
1 1 COIL COIL A A 1 1 1 A COIL
COIL COIL A A
8 8 8 2 2 2 8 8 8 2 2 2 8 8 8 2 2 2
7 3 3 3 7 7 7 3 3 3 7 3 3 3
7 7 SCHEMATIC SCHEMATIC 7 7
SCHEMATIC J421
SCHEMATIC J421D
SCHEMATIC
SCHEMATIC J421DD
(Coil6422
A Last 6422
Last422
6 A Last Energized)
A (Coil
(CoilEnergized) 6 A422D
(Coil Last
6 422D
6Energized)
A4(Coil 422D
A Last Energized)
4 6 422DD
6 422DD
SCHEMATIC 422DD
6SCHEMATIC
SCHEMATIC
4 Energized) 4
54 View)
(Coil Last Energized)
54 4
54 Energized)
4Last Energized)
A (Coil
422H 422H
View)5(Bottom
5 (Bottom
(Bottom 422HView) 5 (Bottom
(Bottom 5 (Bottom
View) View) View) (Coil A Last
(Coil 5 A Last
5 Energized)
View) (Bottom
(Bottom(Bottom View) View)
422K422K
422K
COIL ACOILCOIL
A A COIL ACOILCOIL
A A COIL ACOILCOIL
A A
722 722722
COIL BCOILCOIL
B B COIL BCOILCOIL
B B COIL BCOILCOIL
B B
SCHEMATIC
SCHEMATIC
SCHEMATIC SCHEMATIC
SCHEMATIC
SCHEMATIC
10
(Coil
(Coil A Last A LastA10
(Coil
Energized)Last 10
Energized)
Energized) 10Energized)
(Coil
(Coil A Last 10
(Coil
A Last 10Energized)
A Energized)
Last SCHEMATIC
SCHEMATIC
SCHEMATIC
10 10 10
9420 9(Bottom
(Bottom 19 420
420(Bottom
View) View)1View)1 9(Bottom
420D 9(Bottom
420D
View) 420D
19(Bottom1 View)
View) 1 (Coil9A420DD 9(Coil
(Coil
Last A420DD
1
Last
Energized) 420DD
9A Energized)
Last Energized)
1 1
View)(Bottom
(Bottom (Bottom View)View)
8 8 8 2 2 2 8 8 8 2 2 2 8 8 8 2 2 2
7 7 7 3 3 3 7 7 7 3 3 3 7 7 7 3 3 3
6 6 6 6 6 6 6 6 6
9 5 B 94 5 9 45 4 1
COIL BCOIL BCOIL 9 5B 9 4 5 9 45
COIL BCOIL BCOIL 4
1 9 5B 94 5 9 45 4 1
COIL BCOIL BCOIL
1 1 1 1 1 1
8 8 8 2 2 2 8 8 8 2 2 2 8 8 8 2 2 2
COIL ACOILCOIL
A A COIL ACOILCOIL
A A COIL ACOILCOIL
A A
7 7 3 37 3 7 7 3 7 3 3 7 7 3 7 3 3
6 6 6 6 6
6J422D 6 6 6
SCHEMATIC
5SCHEMATIC J422
4SCHEMATIC
5 45 4 SCHEMATIC
5 SCHEMATIC 4
4 5SCHEMATIC
45 J422DD
5 45 45 4
(Coil A Last
(CoilEnergized)
A(Coil
LastAEnergized)
Last Energized) (Coil A Last
(CoilEnergized)
A(Coil
LastAEnergized)
Last Energized) SCHEMATIC
SCHEMATIC
SCHEMATIC
(Bottom(Bottom
View)(Bottom
View) View) (Bottom(Bottom
View)(Bottom
View) View) (Coil A Last
(CoilEnergized)
A(Coil
LastAEnergized)
Last Energized)
COIL A
COIL ACOIL A COIL A
COIL ACOIL A (Bottom(Bottom COIL
View)(Bottom
View) View) COIL A
ACOIL A

SCHEMATIC
SCHEMATIC
SCHEMATIC SCHEMATIC
SCHEMATIC
SCHEMATIC
(Coil A Last A (Coil A Last Energized)
(CoilEnergized)
Last Energized) (Coil A Last A (Coil A Last Energized)
(CoilEnergized)
Last Energized) SCHEMATIC
SCHEMATIC
SCHEMATIC
View) (Bottom
(Bottom(Bottom View) View) View) (Bottom
(Bottom(Bottom View) View) (Coil A Last A (Coil A Last Energized)
(CoilEnergized)
Last Energized)
View) (Bottom
(Bottom(Bottom View) View)

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 27

 HIGH-PERFORMANCE RELAYS

Series 412H, 422H & 432H Electromechanical Relays - High Temperature

The TO-5 relay, originally conceived and developed by Teledyne, has become one of the industry standards • All welded construction
for low-level switching from dry circuit to 1 ampere. Designed for high-density PC board mounting, these • Unique uni-frame design providing high
TO-5 relays are some of the most versatile ultraminiature relays available because of their small size and low magnetic efficiency and mechanical rigidity
coil power dissipation. • High force/mass ratio for resistance to shock
The H Series high-temperature TO-5 relays are designed for reliable operation in elevated ambient and vibration
temperatures up to 200°C. Special material selection and processing provide assurance of freedom from • Precious metal alloy contact material with
contact contamination and mechanical malfunctioning that might otherwise be caused by ultra high ambient gold plating assures excellent high current
temperature conditions. and dry circuit switching capabilities
Typical applications:
  • Oil exploration (down-hole) instrumentation
  • High-Temperature industrial and process control instrumentation

421 421D
Relay Type Nominal Coil
  412H = DPDT Non-Latching Part No. D.O.V (Vdc) Contact Load Rating
Voltage Resistance P.U.V
  432H = DPDT Non-Latching (Vdc) (Ω) (Vdc) (max.) min. max.

m
  422H = DPDT Magnetic- COIL B
 COIL B
92.4 9
5 50 4.7 0.14 1 Resistive: 1A/28Vdc 1
     Latching 8 8
6 98 5.9 0.18 3.4  2 Inductive: 200mA/28Vdc (320mH)7 2

co
7 4 4
Coil Type 9 220 9.0 COIL A0.35 65.1   Lamp: 100mA/28Vdc 6
412H
  412H = Standard Coil 12 390 11.9 0.41 6.8   Low Level: 10 to 50 uA/10 to 50 mV
  422H = Standard Coil 18 880 17.8 0.59 10.2

s.
SCHEMATIC SCHEMATIC
(Coil A Last Energized) (Coil A Last Energized)
  432H = Sensitive Coil 26 1560 24.0 0.89 13.5
(Bottom View) (Bottom View)

Vibration 5 100 4.7 0.14 2.4   Resistive: 1A/28Vdc

nt
  30 g’s to 3000 Hz 6 200 5.9 0.18 3.4   Inductive: 200mA/28Vdc (320mH)
9 411/431 400 411D/431D0.35
9.0 5.1 411DD/431DD 411T/431T
  Lamp: 100mA/28Vdc
Shock
ne

432H 420 420D

12 850 11.9 0.41 6.8   Low Level: 10 to 50 uA/10 to 50 mV
  412H = 75 g’s 6 msec, half-sine
184 1 1600 17.8
4 0.59 10.2 4 9 1
  432H = 75 g’s 6 msec, half-sine 5 5 1 5 1
8
2
26 3300 24.0 0.89
COIL B 13.5
9 COIL B 9
po

1 1
  422H = 100 g’s 2
7 3
8 2
3 2 3 2 8 3 2 6 4
Acceleration Nominal Coil 7 3 7 3

  50 g’s
Part No. Voltage
SCHEMATIC Resistance Set & Reset
SCHEMATIC
6
5 4 Contact
SCHEMATIC Load Rating 6
5 4
m

SCHEMATIC
(Ω)
(Bottom View) (Bottom View) (Bottom View)
(Vdc) Voltage (Vdc) (Bottom View)
Temperature COIL A COIL
5 61 4.7   Resistive: 1A/28Vdc
  Operating & Storage: SCHEMATIC SCHEMATIC
co

6 120 5.9   Inductive: 200mA/28Vdc (320mH)

(Coil A Last Energized) (Coil A Last Energized)
(Bottom View) (Bottom View)
  –65°C to +200°C
9 280 9.0   Lamp: 100mA/28Vdc
422H
12 500 11.9   Low Level: 10 to 50 uA/10 to 50 mV
e

18 1130
412/432
17.8
412D/432D 412DD/432DD 412T/432T
lin

26 2000
412H/432H 24.0
412DV/432DV 412DDV 712TN/732TN
412K 712D/732D 422 422D
412V 422H
712/732 422K
722
on

COIL B COIL B
10 10
9 1 9 1 10 9 1
9 1
8 2 9 2 1 9 8 2
8 2 8 1
8 2 8 2 3
7 3 7 3 7
7 3
6 4 6 7 3 7 63
6 4 4 4
5 6 4 6 4 5
HIGH-PERFORMANCE

Schematics as viewed from terminals 412H COIL A COI

SCHEMATIC SCHEMATIC SCHEMATIC SCHEMATIC
432H
(Bottom View) (Bottom View) (Bottom View) (Bottom View)
P.U.V = Pick-Up Voltage SCHEMATIC SCHEMATIC
(Coil A Last Energized) (Coil A Last Energized)
D.O.V = Drop-Out Voltage (Bottom View) (Bottom View)
422H

Page 28 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 HIGH-PERFORMANCE RELAYS

Series 412K & 422K Electromechanical Relays - High Shock

The TO-5 relay, originally conceived and developed by Teledyne, has become one of the industry standards • All welded construction
for low-level switching from dry circuit to 1 ampere. Designed for high-density PC board mounting, its • Unique uni-frame design providing high
small size and low coil power dissipation make the TO-5 relay one of the most versatile subminiature relays magnetic efficiency and mechanical rigidity
available. • High force/mass ratio for resistance to shock
The K Series high-shock TO-5 relays are designed to withstand shock levels up to 4000 g’s, .5 msec and vibration
duration. Special material selection and construction details provide assurance that critical elements of the 421 42
• Precious metal alloy contact material with
relay structure and mechanism will not be permanently displaced or damaged as a result of extremely high g gold plating assures excellent high current
level shocks. and dry circuit switching capabilities
Typical applications:
  • Commercial avionics aircraft control COIL B
COIL B 9
  • Commercial aircraft control systems 9
1
  • Transportation systems (rail/truck) 8
2
8
7
7 4

COIL A 6 6
Relay Type Nominal Coil
  412K = DPDT Non-Latching Part No. D.O.V (Vdc) Contact Load Rating
Voltage Resistance P.U.V SCHEMATIC SCH
  422K = DPDT Magnetic- (Vdc) (Ω) (Vdc) (max.)

m
(Coil A Last Energized) (Coil A La
min. max. (Bottom View) (Bot
     Latching
5 50 4.3 0.14 2.5   Resistive: 1A/28Vdc
Vibration

co
6 80 5.2 0.18 3.2   Inductive: 200mA/28Vdc (320mH)
  30 g’s to 3000 Hz 411/431
9 160 411D/431D
7.6 0.35 411DD/431DD   Lamp: 100mA/28Vdc
4.9 411T/431T
412K 420 42
Shock 12 300 10.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV

s.
  412K = 75 g’s 6 msec, half-sine 4 18 1 600 4 14.3 0.59 10.0
4 9 1
5 1 5 1 2
5
     4000 g’s, 0.5 msec axial 26 1350 21.0 0.89 13.0
COIL B 9
1
8 COIL B 9
3
nt 7 8
     plane, half-sine 3 2 3 2 3 8 2 2
6 4
Nominal Coil 7 3 7
     1000 g’s, 0.5 msec side 6
Part No. Voltage ResistanceSCHEMATIC
SCHEMATIC Set & Reset Contact
SCHEMATIC
5 4 Load Rating
6
5
ne

     planes, half-sine SCHEMATIC

(Ω)
(Bottom View) (Bottom View) (Bottom View)
(Vdc) Voltage (Vdc) (Bottom View)
  422K = 100 g’s 6 msec, half-sine COIL A
5 61 3.5   Resistive: 1A/28Vdc
     2100 g’s, 0.5 msec axial SCHEMATIC SCH
6 120 4.5   Inductive: 200mA/28Vdc (320mH)
(Coil A Last Energized) (Coil A
po

     plane, half-sine (Bottom View) (B

9 280 6.8   Lamp: 100mA/28Vdc
     750 g’s, 0.5 msec side 422K
12 500 9.0   Low Level: 10 to 50 uA/10 to 50 mV
     planes, half-sine
18 1130 13.5
m

Acceleration 412/432 412D/432D 412DD/432DD 412T/432T

26412H/432H2000 18.0
412DV/432DV 412DDV 712TN/732TN
  50 g’s 412K 712D/732D 422 42
422H
co

412V
Temperature 712/732 422K
722
  Operating & Storage: COIL B COIL B
  –65°C to +125°C
e

10
9 1 9 1 10 9
9 1
8 2 9 8 1 2 9 8
lin

8 2 1
8 2 8 2
7 3 7 3 7
7 3
7 6 3 7 3 6
6 4 4 4
6 5 4
6 6 4
on

412K COIL A
SCHEMATIC SCHEMATIC SCHEMATIC SCHEMATIC
(Bottom View) (Bottom View) (Bottom View) (Bottom View)
SCHEMATIC SCH
(Coil A Last Energized) (Coil A L
(Bottom View) (Bo
422K

Schematics as viewed from terminals

P.U.V = Pick-Up Voltage
D.O.V = Drop-Out Voltage

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 29

 HIGH-PERFORMANCE RELAYS

Series 412V & 432V Electromechanical Relays - High Vibration

The 412V and 432V TO-5 relays, originally conceived and developed by Teledyne, have become the industry • All welded construction
standards for low level switching from dry circuit to 1 ampere in high-vibration environments. Designed • Unique uni-frame design providing high
for high-density PC board mounting, these TO-5 relays are some of the most versatile ultraminiature relay magnetic efficiency and mechanical rigidity
available because of their small size and low coil power dissipation. • High force/mass ratio for resistance to shock
The V Series high-vibration relays are designed to withstand vibration levels of 250 to 380 g’s at the and vibration
frequencies noted, when tested on a resonant beam for 10 to 20 seconds, in the axis parallel to contact • Precious metal alloy contact material with
motion (x-axis), or 100 g’s 10-2000 Hz for 20 minutes in the x-axis. A unique magnetic circuit prevents gold plating assures excellent high current
contact opening (chatter) in excess of 10 microseconds under vibration or shock conditions. and dry circuit switching capabilities
Typical applications:
  • Avionics aircraft control
  • Aircraft control systems
  • Transportation systems (rail/truck)

Relay Type Nominal Coil

  DPDT Non-Latching Part No. Voltage Resistance P.U.V D.O.V (Vdc) Contact Load Rating
(Vdc) (Ω) (Vdc) (max.)

m
Coil Type min. max.

  412V = Standard Coil 5 50 4.6 0.14 2.3   Resistive: 1A/28Vdc

co
  432V = Sensitive Coil 6 70 5.5 0.18 3.2   Inductive: 200mA/28Vdc (320mH)
Diode Options 412V 9 155 8.2 0.35 4.9   Lamp: 100mA/28Vdc
  D = Internal diode for coil 412DV 12 235 11.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV

s.
  transient suppression 18 610 16.5 0.59 10.0
  DD = Internal diode for coil 26411/431 1130 411D/431D
411/431 411D/431D
22.0 13.0411DD/431DD
0.89 411DD/431DD 411T/431T
411/431 411D/431D 411DD/431DD 411T/431T 411T/431T
nt
  transient suppression and 5 33 4.6 0.6 2.8   Resistive: 1A/28Vdc

  polarity reversal protection 46 1 44 4

5.5 0.7 3.44   Inductive: 200mA/28Vdc
9
(320mH)
1
4 1 4 4 5 1 9 1
4 1 5 41 19 2
ne
4 5 5
5 9 125
1 5 1 8.2 5 0.8 5.31   Lamp: 100mA/28Vdc
8 2
Vibration 5
412DDV 5 1
8 82
3
37
3 12 2 215 3 11.0 2 0.9 6.53   Low
72 Level:
3 7 10 to 50 uA/10 to 50 mV
  250 g’s at 140 ±5 Hz 3 23 2
3 23 2
3 2 3 2 6
6
4
4
18 470 16.5 1.1 10.0 6 4
  350 g’s at 170 ±5 Hz
po

SCHEMATIC
26 1050 SCHEMATIC
22.0 1.4 13.0 SCHEMATIC
  380 g’s at 200 ±5 Hz SCHEMATIC SCHEMATIC SCHEMATIC SCHEMATIC
(Bottom View) SCHEMATIC SCHEMATIC
(Bottom View) (Bottom View) SCHEMATIC
(Bottom View)
(Bottom View) (Bottom View) (Bottom View)
SCHEMATIC SCHEMATIC(Bottom View)
5 (Bottom View)
80 4.6 0.14
(Bottom View)
2.5   Resistive:
(Bottom 1A/28Vdc
(Bottom View)
View)
Shock
6 120 5.5 0.18 3.2   Inductive: 200mA/28Vdc (320mH)
m

  150 g’s 11 msec, half-sine 432V 9 240 8.2 0.35 4.9   Lamp: 100mA/28Vdc
Acceleration 432DV 12 480 11.0 0.41 6.5   Low Level: 10 to 50 uA/10 to 50 mV
co

  50 g’s 18 950 16.5 0.59 10.0

26 412/432 1900
412/432 22.0
412D/432D0.89
412D/432D 13.0 412DD/432DD
412DD/432DD 412T/432T
Temperature 412/432 412D/432D
412H/432H 412DD/432DD
412DV/432DV 412T/432T 412T/432T
412H/432H412H/432H 412DV/432DV 412DDV 412DDV 412DDV
412DV/432DV
712TN/732TN
712TN/732TN
712TN/732TN
  Operating & Storage: 412K 712D/732D
e

412K 712D/732D
412K
412V 412V 712D/732D
  –65°C to +125°C 412V 712/732
lin

712/732 712/732

9 1 10
9 1 9 1 10
on

9 1 1 10
1 8 9 2 1 9 8 2
91 9
8 8
2 2 82 2 9 1 9 2 9
9 1
8 8 18 2
7 3 82 2 1 82 2
7 8 3
7 73
6
3
4 73 3 7 38 7 3
7 64 4 73 3 73 3
4 6 4 7 6 4 7 6
6 6 4 6 4
4 6 4 6 4
6 6 4

412V SCHEMATIC 412DVSCHEMATIC 412DDV

SCHEMATIC SCHEMATIC
SCHEMATIC SCHEMATIC SCHEMATIC SCHEMATIC SCHEMATIC SCHEMATIC SCHEMATIC SCHEMATIC (Bottom View)
432V (Bottom View)(Bottom View)
(Bottom View)
432DV
(Bottom
(Bottom View)
View)
(Bottom View)
(Bottom View)
(Bottom View)
(Bottom View)
(Bottom View)
(Bottom View)
HIGH-PERFORMANCE

Schematics as viewed from terminals

P.U.V = Pick-Up Voltage
D.O.V = Drop-Out Voltage

Page 30 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 APPENDIX: signal integrity eye diagrams

SERIES RF100
Normally Closed Normally Open

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

m
Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
233.7 mV 88.88 ps 13.01 9.33 ps 217.1 mV 88.05 ps 11.55 8.44 ps

co
s.
SERIES GRF100 nt
Normally Closed Normally Open
ne

+130 mV +130 mV
po

0V 0V
m

-130 mV -130 mV
co

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
e

242.5 mV 90.09 ps 14.20 8.44 ps 263.6 mV 87.29 ps 20.23 9.78 ps

lin
on

SERIES SGRF100
Normally Closed Normally Open

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
251.5 mV 92.04 ps 15.11 8.00 ps 261.2 mV 87.64 ps 18.20 8.44 ps

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 31

 APPENDIX: signal integrity eye diagrams

SERIES GRF172
Normally Closed Normally Open

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

m
Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
246.1 mV 92.45 ps 14.59 6.22 ps 268.2 mV 90.87 ps 21.62 7.56

co
s.
SERIES RF300/RF303
Normally Closed Normally Open
nt
ne

+130 mV +130 mV
po

0V 0V
m

-130 mV -130 mV
co

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
e

254.7 mV 90.38 ps 18.52 8.44 ps 250.9 mV 88.21 ps 16.84 8.00 ps

lin
on

SERIES GRF300/GRF303
Normally Closed Normally Open

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
237.6 mV 90.08 ps 14.19 9.33 ps 255.2 mV 88.93 ps 17.74 8.89 ps

Page 32 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 APPENDIX: signal integrity eye diagrams

SERIES SGRF300/SGRF303
Normally Closed Normally Open

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

m
Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
233.3 mV 89.08 ps 13.18 7.56 ps 243.1 mV 90.29 ps 15.21 7.56 ps

co
s.
SERIES SRF300/SRF303
Normally Closed Normally Open
nt
ne

+130 mV +130 mV
po

0V 0V
m

-130 mV -130 mV
co

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
e

137.9 mV 85.83 ps 6.31 13.33 ps 72.8 mV 88.1 ps 4.31 8.00 ps

lin
on

SERIES RF312
Normally Closed Normally Open

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
266.5 mV 89.21 ps 19.44 9.78 ps 264.3 mV 89.07 ps 19.13 8.00 ps

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 33

 APPENDIX: signal integrity eye diagrams

SERIES GRF312
Normally Closed Normally Open

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

m
Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
266.5 mV 91.09 ps 20.75 6.22 ps 239.6 mV 92.77 ps 14.52 5.78 ps

co
s.
SERIES SGRF312
Normally Closed Normally Open
nt
ne
+130 mV +130 mV
po

0V 0V
m

-130 mV -130 mV
co

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
e

240.7 mV 91.44 ps 15.49 8.44 ps 237.1 mV 89.08 ps 13.72 8.00 ps

lin
on

SERIES RF311/RF331
Normally Closed Normally Open

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
266.5 mV 89.21 ps 19.44 9.78 ps 264.3 mV 89.07 ps 19.13 8.00 ps

Page 34 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 APPENDIX: signal integrity eye diagrams

SERIES GRF311
Normally Closed Normally Open

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

m
Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
260.0 mV 92.32 ps 17.98 6.67 ps 267.2 mV 90.99 ps 20.84 7.11 ps

co
s.
SERIES GRF342
Normally Closed Normally Open
nt
ne

+130 mV +130 mV
po

0V 0V
m

-130 mV -130 mV
co

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
e

252.9 mV 90.74 ps 16.53 8.44 ps 253.1 mV 87.31 ps 17.57 9.78 ps

lin
on

SERIES RF180
Normally Closed Normally Open

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
240.5 mV 88.16 ps 13.86 10.67 ps 235.8 mV 87.22 ps 12.75 10.22 ps

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 35

 APPENDIX: signal integrity eye diagrams

SERIES RF341
Normally Closed Normally Open

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

m
Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
260.9 mV 88.26 ps 18.39 8.44 ps 271.5 mV 86.41 ps 21.35 8.89 ps

co
s.
SERIES GRF341
Normally Closed Normally Open
nt
ne

+130 mV +130 mV
po

0V 0V
m

-130 mV -130 mV
co

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
e

256.2 mV 87.70 ps 17.15 8.89 ps 259.9 mV 88.39 ps 17.59 8.00 ps

lin
on

SERIES RF310/RF313
Normally Closed Normally Open

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
246.1 mV 92.45 ps 14.59 6.22 ps 268.2 mV 90.87 ps 21.62 7.56 ps

Page 36 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 APPENDIX: signal integrity eye diagrams

SERIES RF320/RF323
Normally Closed Normally Open

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

m
Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
246.1 mV 92.45 ps 14.59 6.22 ps 268.2 mV 90.87 ps 21.62 7.56 ps

co
s.
SERIES A150
Attenuated Path Thru Path
nt
ne

+130 mV +130 mV
po

0V 0V
m

-130 mV -130 mV
co

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
e

45.59 mV 64.18 ps 5.70 28.00 ps 130.2 mV 72.87 ps 5.29 20.89 ps

lin
on

SERIES GA150
Attenuated Path Thru Path

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
62.10 mV 83.23 ps 7.14 12.89 ps 130.3 mV 78.38 ps 5.30 19.56 ps

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 37

 APPENDIX: signal integrity eye diagrams

SERIES A152
Attenuated Path Thru Path

+130 mV +130 mV

0V 0V

-130 mV -130 mV

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

m
Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
45.10 mV 78.94 ps 5.57 18.67 ps 124.5 mV 73.90 ps 5.23 22.22 ps

co
s.
SERIES GA152
Attenuated Path Thru Path
nt
ne

+130 mV +130 mV
po

0V 0V
m

-130 mV -130 mV
co

0 ps 40 ps 80 ps 120 ps 160 ps 0 ps 40 ps 80 ps 120 ps 160 ps

Eye Height Eye Width SNR JitterP-P Eye Height Eye Width SNR JitterP-P
e

67.99 mV 82.70 ps 7.85 13.78 ps 122.9 mV 76.21 ps 5.07 21.78 ps

lin
on

PATTERN GENERATOR SETTINGS

  10 Gbps Random Pulse Pattern Generator
  231 - 1 PRBS signal
  PRBS output of 300mVP-P (nominal)
  RF PCB effect (negligible) not removed from measurement
  Data shown is typical of both poles

Page 38 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 RoHS and REACH CERTIFICATE OF
COMPLIANCE
RoHS

It is hereby stated and certified that Teledyne Relays complies with the Restrictions on Haz-
ardous Substances (RoHS) Directives to the extent herein:

Teledyne Relays does not use any of the Restricted Substances specified by the RoHS Di-
rectives (listed below) as components in TO-5 and Centigrid ® Electromechanical

m
Relay products, nor are these substances employed during any electromechanical relay
manufacturing process:

co
Lead

s.
Mercury
Cadmium
nt
Hexavalent Chromium
Polybrominated Biphenyls (PBB’s)
ne

Polybrominated Diphenyl Ethers (PBDE’s)

po

However, upon request from the Customer, relay leads may be coated with solder, which
contains 60% tin and 40% lead.
m
e co

REACH
lin

It is hereby stated and certified that Teledyne Relays complies with the Registration
Evaluation Authorization and Restriction of Chemicals (REACH) Directives to the extent
on

stated herein:

Teledyne Relays is a manufacturer of articles. Teledyne Relays has taken the initiative to
review the (39) substances that are under consideration for treatment as Substances of Very
High Concern (SVHC) candidates. Teledyne Relays confirmed that our relays do not contain
any of the listed substances in concentration >0.1% weight per supplied article, substance or
preparation weight.

For Additional Information please E-Mail us at: [email protected]

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 39

 Appendix: TELEDYNE RELAYS PART NUMBERING SYSTEM

RF Attenuator Relays

A150 - 20 - 5 / S Q
Relay Series
Q = Solder-Coated Leads1
G = Gold-Plated Leads (RoHS Compliant)
Attenuation Value (dB) R = RoHS Compliant Solder2

S = 0.187” Leads
Nominal Coil Voltage No Suffix = 0.75” Leads
(26 = 26.5 V)

RF Relays (Except Attenuator Relays)

m
RF100 X - 26 / S Q
Relay Series

co
Q = Solder-Coated Leads1
G = Gold-Plated Leads (RoHS Compliant)
Ground Pin Option
R = RoHS Compliant Solder2
(See Appendix A)

s.
* Not Applicable for GRF Relays
S = 0.187” Leads
No Suffix = 0.75” Leads3
nt
Nominal Coil Voltage
ne

(26 = 26.5 V)

T2R Established Reliability Relays

po

ER 114 Y M4 - 26 A / S Q
m

Established Reliability Designator Q = Solder-Coated Leads1

G = Gold-Plated Leads (RoHS Compliant)
Relay Series
co

R = RoHS Compliant Solder2

Ground Pin Option
(See Appendix A) S = 0.187” Leads
W = 1.5” Leads
e

Pad Option
No Suffix = 0.75” Leads
(See Appendix A)
lin

Nominal Coil Voltage Screening and Reliability Level

(26 = 26.5 V) (See Appendix B for Screening Options)
on

Military Qualified (JAN) Relays

J 114 Z M4 - 26 P L
Military (JAN) Designator Screening and Reliability Level
(See Appendix B for Screening Options)
Relay Series
P = 0.187” Leads
Ground Pin Option
W = 1.5” Leads
(See Appendix A)
No Suffix = 0.75” Leads
Pad Option
(See Appendix A) Nominal Coil Voltage
(26 = 26.5 V)

General Note: Parts ordered without suffix may be supplied with Solder-Coated or Gold-Plated leads
1
Parts ordered with Solder-Coated leads will have (Sn60/Pb40)
2
Parts ordered with RoHS Solder-Coated leads will have (Sn99.3/Cu0.7)
3
Not Applicable to GRF relays

Page 40 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 Appendix: TELEDYNE RELAYS PART NUMBERING SYSTEM

Commercial Surface Mount Relays

S114 - 26 / R
Q = Solder-Coated Leads1
Relay Series (Surface Mount Relays are Solder-Coated by default)
R = RoHS Compliant Solder2

Nominal Coil Voltage

(26 = 26.5 V)

Commercial Relays, (Except Surface Mount Relays)

m
172 Y M4 - 26 / S Q

co
Q = Solder-Coated Leads1
Relay Series G = Gold-Plated Leads (RoHS Compliant)
R = RoHS Compliant Solder2
Ground Pin Option
(See Appendix A)
Pad Option
s. S = 0.187” Leads
nt
No Suffix = 0.75” Leads
(See Appendix A)
Nominal Coil Voltage
(26 = 26.5 V)
ne

High Performance Relays

po

412DV X M - 26 / S G
m

Relay Series Q = Solder-Coated Leads1

G = Gold-Plated Leads (RoHS Compliant)
co

Ground Pin Option R = RoHS Compliant Solder2

(See Appendix A)
S = 0.187” Leads
e

Pad Option W = 1.5” Leads

(See Appendix A)
lin

No Suffix = 0.75” Leads

Nominal Coil Voltage
(26 = 26.5 V)
on

General Note: Parts ordered without suffix may be supplied with Solder-Coated or Gold-Plated leads.
1 Parts ordered with Solder-Coated leads will have (Sn60/Pb40)
2 Parts ordered with RoHS Solder-Coated leads will have (Sn99.3/Cu0.7)

If you don’t see what you’re looking for

in this Selection Guide, contact us!
© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 41
 APPENDIX: Spacer Pads

Pad designation and Dim. H

Height For use with the following:
bottom view dimensions Max.
ER412, ER412D, ER412DD .295 (7.49)
Ø.150
[3.81]
Ø.150
712, 712D, 712TN,
[3.81] .300 (7.62)
(REF)
(REF) RF300, RF310, RF320
Ø.150 Dim H
Dim H
[3.81] Ø.150 MAX
MAX
ER420, ER422D, ER420DD, 421,
(REF) [3.81]
(REF)
ER421D, ER421DD, ER422, ER422D, .305 (7.75)
Ø.150
Ø.150 [3.81] Dim H ER422DD, 722, 722D, RF341
[3.81] Ø.150 MAX Dim H
(REF)
(REF)
MAX ER431T, ER432T,
Ø.150 [3.81]
Dim H .400 (10.16)
[3.81] (REF)
Dim H MAX ER432, ER432D, ER432DD
(REF)
MAX Dim H
Dim H MAX 732, 732D, 732TN, RF303, RF313, RF323 .410 (10.41)
MAX
“M4” Pad for TO-5 RF312 .350 (8.89)

m
Dim H
MAX
Dim H ER411, ER411D, ER411DD, ER411T .295 (7.49)
MAX

co
Dim H
MAX Dim H
MAX ER431, ER431D, ER431DD .400 (10.16)

s.
Dim H
Dim H MAX
MAX Dim H
RF311 .300 (7.62)
Dim H MAX
nt
MAX

RF331 .410 (10.41)

ne

“M4” Pad for TO-5 Dim H

Dim H
MAX
MAX 172, 172D .305 (7.75)
po

Dim H
MAX Dim H
ER114, ER114D, ER114DD,
MAX .300 (7.62)
Dim H J114, J114D, J114DD
Dim H MAX
m

MAX Dim H
Dim H MAX
ER134, ER134D, ER134DD,
.156 MAX .400 (10.16)
co

[3.96]
.156 J134, J134D, J134DD
[3.96]
(REF)
(REF)
.156 RF100 .315 (8.00)
.156
e

[3.96]

“M4” Pad for Centigrid®

[3.96]
(REF)
(REF)
Dim H
Dim H RF103 .420 (10.67)
.156 MAX
lin

.156 MAX
[3.96]
.256 [3.96] (REF)
[6.5]
.256
[6.5] (REF)
.156
.156
[3.96] Dim H 122C, A152 .320 (8.13)
(REF)
(REF) [3.96] (REF) MAX Dim H
MAX
on

(REF)
.256
.256 Dim H
[6.5]
(REF) [6.5]
Dim H MAX ER116C, J116C .300 (7.62)
(REF) MAX Dim H
.256 Dim H MAX
.256 [6.5]
[6.5] MAX
(REF)
(REF)
.256
.256
[6.5]
ER136C, J136C .400 (10.16)
[6.5] (REF)
(REF)

RF180 .325 (8.25)

A150 .305 (7.75)

“M9” Pad for Centigrid®
Notes:
1. Spacer pad material: Polyester film.
2. To specify an “M4” or “M9” spacer pad, refer to the mounting variants portion of the part numbering
example in the applicable datasheet.
3. Dimensions are in inches (mm).
4. Unless otherwise specified, tolerance is ± .010” (.25 mm).
5. Add 10 mΩ to the contact resistance shown in the datasheet.
6. Add 0.01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet.

Page 42 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 APPENDIX: Spreader Pads

Pad designation and Dim. H

Height For use with the following:
bottom view dimensions Max.
ER411T, J411T, ER412, ER412D
.370[9.4]
.370 [9.4] ER412DD, J412, J412D, J412DD .388 (9.86)
MAX SQ
MAX SQ
.100
.100
ER412T, J412T
.370[9.4]
.370 [9.4]
MAX SQ
MAX SQ [2.54]
[2.54]
Dim HH
Dim
712, 712D, 712TN .393 (9.99)
.100
.100
.370
.370[9.4] MAX
MAX
[9.4]
MAX SQSQ
[2.54]
[2.54] MAX
ER431T, J431T, ER432, ER432D
.150
.150 Dim HH
Dim .014
.014
[3.81]
[3.81]
.100
.100 MAX
MAX [0.36]
[0.36] ER432DD, J432, J432D, J432DD .493 (12.52)
[2.54]
[2.54]
.300
.300
[7.62]
[7.62]
.150
.150
Dim HH
Dim
(REF)
(REF)
.014
.014 ER432T, J432T
[3.81]
[3.81] MAX [0.36]
[0.36]
MAX
.300
.300
[7.62] .150
[7.62]
.100
.100 (REF)
(REF)
.014
732, 732D, 732TN .503 (12.78)
.150 [2.54]
[2.54] .014
[3.81]
[3.81] .370
.370
[0.36]
[0.36]
.300
.300
.100
.100
[2.54]
[2.54] [9.4]
[9.4]
(REF)
(REF) ER420, J420, ER420D, J420D
[7.62]
[7.62] .200
.200 MIN
MIN
.370
.370 ER420DD, J420DD, ER421, J421
[5.08]
[5.08] .100
.100 [9.4]
[9.4] .398 (10.11)
ER421D, J421D, ER421DD

m
.200
.200 [2.54]
[2.54] MIN
MIN
[5.08]
[5.08]
“M” Pad 5/ 6/
.370
.370
[9.4]
[9.4]
J422D, ER422DD, J422DD, 722
.200
.200 MIN
MIN

co
.390
.390 [9.91]
[9.91]
[5.08]
[5.08]
SQ
SQ
ER411T
.100
.100
.390[9.91]
.390 [9.91] ER412, ER412D, ER412DD
[2.54]
[2.54]
.441 (11.20)
SQ
SQ
.100
.100 J412, J412D, J412DD
[2.54]
[2.54]

s.
.390
.390[9.91]
[9.91]
.100
.100
SQ
SQ .150
.150
[2.54]
[2.54] .100
.100 Dim HH
Dim
.100
.300 .100
.300
[3.81]
[3.81]
[2.54]
[2.54] MAX
MAX 712, 712D .451 (11.46)
.150
.150
nt
[2.54]
[7.62] [2.54]
[7.62] Dim HH
Dim
.300 .100
.300
[3.81]
[3.81]
MAX
MAX ER421, ER421D, ER421DD
[7.62]
.100
[7.62] [2.54]
[2.54]
.150
.150 Dim HH
Dim 722, 732D .451 (11.46)
[3.81]
ne
[3.81] MAX
.300
.300 MAX
.130
.130
[7.62]
[7.62] .150
.150 [3.3]
[3.3]
.300
[3.81]
[3.81]
.130
.130
ER431T
.300
[7.62]
[7.62]
.150
.150 [3.3]
[3.3] ER432, ER432D, ER432DD .546 (13.87)
po

[3.81]
[3.81]
.300
.300 .130
.150 .130
[7.62]
[7.62] .150 [3.3]
[3.81] [3.3]
[3.81]
.300
.300 732, 732D .556 (14.12)
“M2” Pad 7/ 8/
.370
.370 [9.4]
[9.4]
[7.62]
[7.62]
m

MAX SQ
MAX SQ
.100
.100
.370[9.4]
.370 [9.4]
MAX SQ
MAX SQ [2.54]
[2.54] ER411, ER411D, ER411DD, ER411TX
Dim HH
Dim ER412X, ER412DX, ER412DDX .388 (9.86)
co

.100
.100
.370
.370[9.4]
[9.4] MAX
MAX
.150
.150
MAX
MAX SQSQ
[2.54]
[2.54]
Dim HH
Dim .014
.014
ER412TX
.100
.100
[3.81]
[3.81] MAX
MAX [0.36]
[0.36]
.300
.300
.150
.150
[2.54]
[2.54] (REF)
(REF) 712X, 712DX, 712TNX .393 (9.99)
Dim HH
Dim .014
.014
e

[7.62]
[7.62]
[3.81]
[3.81] [0.36]
[0.36]
.300
.300 .100
.100
MAX
MAX (REF)
(REF) ER420X, ER420DX, ER420DDX
lin

[7.62] .150
[7.62] .150 [2.54]
[2.54] .014
.014 ER421X, ER421DX, ER421DDX
[3.81]
[3.81] .370
.370 [0.36]
[0.36] .398 (10.11)
.300
.300
[7.62]
.100
.100
[2.54]
[2.54] [9.4]
[9.4]
(REF)
(REF) ER422X, ER422DX
[7.62] .200
.200
[5.08]
[5.08] .100
MIN
MIN
.370
.370 ER422DDX, 722X, 722DDX
.100 [9.4]
[9.4]
on

[2.54]
.200
.200
[5.08]
[5.08]
[2.54] MIN
MIN
.370
.370
ER431, ER431D, ER431DD
[9.4]
[9.4] ER431TX
.200
.200 MIN .493 (12.52)
[5.08]
[5.08]
MIN
ER432X, ER432DX, ER432DDX
ER432TX
“M3” Pad 5/ 6/ 9/ 732X, 732DX, 732TNX .503 (12.78)
Notes:
1. Spreader pad material: Diallyl Phthalate.
2. To specify an “M”, “M2” or “M3” spreader pad, refer to the mounting variants portion of the part number example
in the applicable datasheet.
3. Dimensions are in inches (mm).
4. Unless otherwise specified, tolerance is ± .010” (0.25 mm).
5/. Add 25 mΩ to the contact resistance shown in the datasheet.
6/. Add .01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet.
7/. Add 50 mΩ to the contact resistance shown in the datasheet.
8/. Add 0.025 oz (0.71 g) to the weight of the relay assembly shown in the datasheet.
9/. M3 pad to be used only when the relay has a center pin (e.g. ER411M3-12A, 722XM3-26.)

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 43

 "W" "W" POSITION
POSITION

.100
"Z" "Z" POSITION
POSITION
.100
[2.54] [2.54]

.050 .050
[1.27] [1.27] "X" "X" POSITION
POSITION

APPENDIX: Ground Pin Positions

.100 .100
"U" "U" POSITION
POSITION
[2.54] [2.54] (ER116C and ER136C
(ER116C andonly)
ER136C only)

"Z" "Z" POSITION

POSITION "Z" "Z" POSITION
POSITION
Ø.200 Ø.200
[Ø5.08] [Ø5.08]
"X" "X" POSITION
POSITION Ø.200 Ø.200
[Ø5.08] [Ø5.08]

"Y" POSITION
.100 "Y" POSITION "Y"
"Y" POSITION LEGEND: "Y" POSITION
POSITION

m
36°±3° 36°±3° 45°±3° 45°±3°
[2.54]
Glass Insulated Lead

co
position
"Z" POSITION
TO-5 Relays: TO-5 Relays:
Ground
ER411, Pin position
.100 ER411T, ER412, ER412T, ER420, ER421, ER422, ER431T, ER431, RF311, RF331
[2.54] ER432, ER432T, 712, 712TN, 400H, 400K, 400V, RF300, RF303,

s.
RF341, RF312, RF310, RF313, RF320, RF323 Either Ground Pin or
Insulated Lead position
nt
depending on Relay type

.100
ne

[2.54]
po

"Y" POSITION
.100
[2.54]
m

"W" POSITION "Y" POSITION

.100
[2.54]
co

.100
"Z" POSITION
[2.54] "Z" POSITION
e

.050 .100
lin

[1.27] "X" POSITION [2.54]

on

.100
"U" POSITION
.100
[2.54] (ER116C and ER136C only) [2.54]

Centigrid® Relays: Centigrid® Relays:

RF180, ER116C, 122C, ER136C RF100, RF103, ER114, ER134, 172 "Y" POSITION
"Z" POSITION .100"Z" POSITION
ONØ.200 [2.54]
[Ø5.08] LEGEND: "W" POSITION
ON "X" POSITION Ø.200
LEGEND:
Glass Insulated Lead [Ø5.08]
position .100
"Z" POSITION
ON
TION NOTES
Glass Insulated Lead [2.54]
Indicates
LEGEND:
position ground
Ground Pin pin position
position
1. Terminal views shown
ON 2. Dimensions are in.050 inches (mm)
Indicates glass insulated 3. Tolerances: ± .010 (±.25) unless otherwise specified
[1.27] "X" POSITION
Pin or lead position
Ground
Glass Pin position
Insulated Lead
Either Ground
position
TION Insulated Lead position 4. Ground pin positions are within .015 (0.38) dia. of true position
36°±3°
Indicates
Either ground
Ground
depending
Ground Pin pinor
on "Y"
Pin
Relay
position ortype
lead position depend-
POSITION 5.±3°Ground pin head dia.,"Y"
45° 0.035 (0.89) ref: height 0.010 (0.25) ref.
POSITION
ing on relayLead
Insulated type position "U"
6. Lead dia. 0.017 (0.43) nom. .100
POSITION
depending
Either Groundon
PinRelay
or type (ER116C and ER136C
[2.54]
Insulated Lead position
depending on Relay type
Page 44 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 APPENDIX: Teledyne Relays T2R Program

Teledyne Relays’ program was developed to provide the JAN relay user an alternate means of specifying and procuring
established reliability relays. The form, fit and function of a relay is the same as that of its JAN counterpart. program
requirements differ in certain regimens/tests found in both MIL-PRF-28776 and
MIL-PRF-39016 that add cost but no value to the relay.

This program parallels the military specifications in most aspects. The components that make up such a program are intricate
and varied. Furthermore, there are additional options of high value for design, manufacturability and operation of high reliability
assemblies. The following page presents a table that compares the 100% screening performed on JAN relays and relays
prior to shipment.

Other significant highlights of the program include:

m
• Two unique screening levels
• The ability to define lead finish

co
• Spacer pad options which may not be available in military specifications
• Ground pin options which may not be available in military specifications

s.
• Reduced lead time
• Reduced cost
nt
The program is fully defined for both general product requirements and detailed product requirements in the following Teledyne
ne

Relays specifications:
po

TR-R-1
TR-STD-1
m

TR-STD-2
TR-ERL-1
co

TR-R-1/XXX
TR Supplement
e
lin

Copies of these documents are available from Teledyne Relays. We suggest that users check with Teledyne Relays from time
to time to assure that they have the latest issue.
on

Can’t Find What You Need?

Check out our full line of relays and switches. Order literature online at
http://www.teledynerelays.com/lit-request.asp

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 45

 APPENDIX: Teledyne Relays T2R Program

Screening Levels
INSPECTION A Level B Level JAN L Level JAN M Level
1.5%/10K Cycles .75%/10K Cycles 3%/10K Cycles 1%/10K Cycles
Subgroup 1
Screening, Internal Moisture AQL1 4 4 4 4
Vibration (Sinusoidal) AQL 1
4
Vibration (Sinusoidal) 100% 4 4
Screening, Burn-In (Hybrids only) 4 4
Screening, Run-In (Room Temperature) 4
Screening, Run-In (+125°C and –65°C) 4 4 4
Subgroup 2

m
Coil Resistance or Coil Current 4 4 4 4

co
Insulation Resistance 4 4 4 4
Dielectric Withstanding Voltage 4 4 4 4

s.
Static Contact Resistance 4 4 4 4
Pickup and Dropout or Set and Reset
nt
4 4 4 4
Voltage
Operate and Release or Set and Reset Time 4 4 4 4
ne

Hold Voltage 4 4
Turn-On and Turn-Off Time (Hybrids only) 4 4 4 4
po

Contact Bounce Time 4 4

Contact Stabilization Time 4 4
m

Turn-On Current (T Hybrids only) 4 4 4 4

Turn-On Voltage (C Hybrids only)
co

4 4 4 4
Turn-Off Voltage (Hybrids only) 4 4 4 4
Coil Transient Suppression
e

4 4 4 4
(D, DD and Hybrids only)
lin

Diode Blocking Integrity (DD only) 4 4 4 4

Zener Voltage (C Hybrid only) 4 4 4 4
on

Neutral Screen (Latching Relays only) 4 4 4 4

Break Before Make Verification 4 4
Contact Simultaneity 4 4
Subgroup 3
Solderability 2 Samples per Daily Solderability
4 4 4 4
Inspection Lot
Leak Test 4 4 4 4
External Visual and Mechanical Inspection 2/Lot for
4 4 4 4
Dimension and Weight Check

1 AQL = Acceptable Quality Level

Page 46 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 Teledyne Relays HI-REL Program

Teledyne Relays: Because in deep space

there is no acceptable failure rate
Teledyne Relays has a long history of supplying High Relay Types
Reliability relays for use in space bound vehicles. From the TO-5 Magnetic-Latching Relays
earliest deep space probes, such as TO-5 Non-Latching Relays
Voyager I, now nearing 21 billion miles out in space, to the TO-5 Magnetic-Latching, High-Shock Relays

m
next generation of probes scheduled for the TO-5 Non-Latching, High-Shock Relays
future , Teledyne Relays continues to be the preeminent TO-5 Non-Latching, High-Vibration Relays

co
supplier of Hi-Reliability relays to the space market.
Hi-Rel Screening Capabilities
Teledyne Relays Hi-Reliability Specification: 100% Open Electrical Inspection
TR-HIREL-1
s.
100% Precap Inspection
nt
• Eliminates the need for customers to develop and maintain Fully Automated Small Particle Inspection
specifications. (Millipore Clean)
ne

• Manufacturing and Quality Assurance requirements are Asynchronous Miss Test

fully defined and documented. Coil Continuity
po

• Meets the general requirements of both ESA/SCC and Sine Vibration

NASA/GSFC documents. Random Vibration
• Offers options for 100% Group A screening High/Low Run In
m

• Offers options for 3 levels of Lot Acceptance Testing (Miss Test) –65 °C ± 125 °C
co

(LAT). Radiographic Inspection

Mechanical Shock Test
Teledyne Screening Document 0-40-837 Thermal Shock Test
e

NASA approved screening regimen based on NASA/GSFC Acceleration

lin

S-311-P.754 Radiographic Inspection (X-ray)

Mechanical Shock Test
on

Thermal Shock Test

Acceleration
Load Banks for a Variety of Life Test Load
Serialized Printed Electrical Data
Continuous Life Testing
Environmental Testing
Vertical Integration

For information or answers to your questions, please visit our

website.

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 47

 APPENDIX: Authorized Distributors
NORTH AMERICA Hot Electronic GmbH NETHERLANDS
ALLIED ELECTRONICS Tel: +49 (0) 89 666 2836 Nijkerk Electronics B.V.
Tel: (800) 433-5700 E-mail: [email protected] Tel: +32 (0) 3 544 7066
www.alliedelec.com/search.asp www.hot-electronic.de E-mail: [email protected]
www.nijkerk-ne.com
ASAP ELECTRONICS MRC Components oHG
Tel: (800) 477-1272 Tel: +49 (0) 8161 98480 NORWAY
www.asapelectronics.com E-mail: [email protected] ARROW Norway A/S
www.mrccomponents.de Tel: +47 (0) 21306532
AVNET E-mail: [email protected]
Tel: (800) 772-8638 Zettler electronics GmbH www.arrowne.com
www.em.avnet.com Tel: +49 (0) 89 800 97-0
E-mail: [email protected] RUSSIA
MASTER DISTRIBUTORS www.zettlerelectronics.com Petersburg Electronic Company JSC
Tel: (888) 473-5297 Tel: +7 812 4488 777
www.onlinecomponents.com INDIA E-mail: [email protected]
Specsynergy Technologies, Inc. www.pec.spb.ru
MOUSER ELECTRONICS San Jose, CA (Main Office)
Tel: (800) 346-6873 Tel: (408) 954-8474 x105 SINGAPORE
www.mouser.com E-mail: [email protected] Device Electronics PTE, Ltd.
Tel: 65-288 6455

m
RICHARDSON ELECTRONICS Specsynergy Technologies, Inc. E-mail: [email protected]
Tel: (800) 737-6937 New Delhi Office
www.rell.com Tel: 91 11 25860 752 SOUTH AFRICA

co
E-mail: [email protected] RF Design
SHERBURN ELECTRONICS Tel:
Tel: (800) 366-3066 ISRAEL National Smart Call: 0861 753 357
www.sherburn.com STG International Ltd. Cape Town: +27 (0) 21 555 8400

s.
Tel: +972 (0) 3 733 1400 Gauteng: +27 (0) 11 695 2200
BELGIUM & LUXEMBOURG E-mail: [email protected] Durban: +27 (0) 31 266 4534
nt
Nijkerk Electronics B.V. www.stggroup.co.il www.rfdesign.co.za
Tel: +32 (0) 3 544 7066
E-mail: [email protected] ITALY SWEDEN
www.nijkerk-ne.com SINCRON s.r.l. ARROW Sweden
ne

Tel: +39 02 95384218 Tel: +46 8 56265500

CHINA & HONG KONG E-mail: [email protected] E-mail: [email protected]
Fiaco Microelectronics www.sincron.it www.arrowne.com
po

Beijing Office
Tel: 86-10-6503-2171 JAPAN MicroComp Nordic AB
E-mail: [email protected] Comcraft Corporation Tokyo Tel: +46 8 607 3910
Tel: 81-3-3395-5553 E-mail: [email protected]
Bright Toward Industrial Co., Ltd. E-mail: [email protected] www.mcnab.se
m

Beijing Office www.comcraft.co.jp

Tel: 86-10-8200-4979 OEM Electronics
co

E-mail: [email protected] Comcraft Corporation Osaka Tel: +46 75 242 4562

Tel: 81-6-6396-7722 E-mail: [email protected]
CZECH REPUBLIC E-mail: [email protected] www.oemelectronics.se
Amtek spol. s.r.o. www.comcraft.co.jp
e

Tel: +420 547 125 555 SWITZERLAND

E-mail: [email protected] KOREA ENA AG
lin

www.amtek.cz Electro-Comm USA Tel: +41 56 6342834

Tel: (818) 848-7790 E-mail: [email protected]
DENMARK E-mail: [email protected] www.ena.ch
ARROW Denmark A/S www.anyeparts.com
on

Tel: +45 (0) 70102211 TAIWAN

E-mail: [email protected] Electro-Comm SEOUL Bright Toward Industrial Co., Ltd.
www.arrowne.com Tel: 82-31-713-4216 Tel: +886-2-822-76000
E-mail: [email protected] E-mail: [email protected]
ESTONIA www.anyeparts.com www.relays.com.tw
ARROW Estonia
Tel: +372 6 774250 LATVIA UNITED KINGDOM
E-mail: [email protected] ARROW Latvia Advanced Power Components plc
www.arrowne.com Tel: +371 7311490 Tel: +44 (0) 1480 226603
E-mail: [email protected]   E-mail: [email protected]
FINLAND www.arrowne.com   www. apc-plc.co.uk
ARROW Finland Oy
Tel: +358 9 3212 831 LITHUANIA Arrow Electronics UK Ltd.
www.arrowne.com ARROW Lithuania Tel: +44 (0) 1279 626 777
Tel: +370-37-759015 www.arrowne.com
FRANCE E-mail: [email protected]  
ARROW France www.arrowne.com     Willow Technologies Ltd.
Tel: +33 1 4978 4960 Tel: +44 (0) 1342 835 234
E-mail: [email protected] MALAYSIA E-mail: [email protected]
Device Electronics PTE, Ltd. www.willow.co.uk
GERMANY Tel: (603) 7880 8626/8636
Adelco Elektronik GmbH E-mail: [email protected] 2001 Electronic Components Ltd.
Tel: +49 (0) 4106 61040 Tel: +44 (0) 1438 742 001
E-mail: [email protected] E-mail: [email protected]
www.adelco-elektronik.de www.2001elec.co.uk

Page 48 (800) 284-7007 • www.teledynerelays.com • +44 (0) 1236 453124 • www.teledyne-europe.com © 2010 TELEDYNE RELAYS
 APPENDIX: Authorized North American Representatives
MacInnis
Sea-Port Synergy Sales
Technical Washington
Sales EK Associates
Montana Maine
North Dakota Minnesota

Oregon RPI-Apex VT
NH MA
South Dakota Wisconsin
Idaho ERI New York RI
Wyoming Michigan
CT
Iowa
No.

PA
Essig & Comp Tech
Cali

Nevada Nebraska
Jay Stone Assoc. So. NJ
for

Illinois Ohio
Associates IN
nia

Utah DE
Colorado MINK Associates WV MD
Virginia Eagle Sales
Kansas Missouri
So.

Kentucky
Cali

North Carolina
for

Tennessee
nia

m
Cain Technology Arizona Oklahoma Arkansas
New Mexico SC

AL
Precision

co
MS Georgia Marketing
LA
Westrep Arizona Texas

s.
FL

CentraMark
nt
Technical HHP Associates
Associates
ne

REPRESENTATIVES
Cain Technology Eagle Sales Corporation Jay Stone & Associates Sea-Port Tech Sales
po

Southern California MD, VA, WA DC, Eastern PA, Northern California WA, OR, ID, Western Canada
2629 Townsgate Road, Suite 200 Southern NJ 2109 O’Toole Avenue, Suite M 3630 130th Ave. NE
Westlake Village, CA 91361 3545 Ellicott Mills Drive, Suite 202 San Jose, CA 95131 Bellevue, WA 98005
Tel: 805-496-5702 Ellicott City, MD 21043 Tel: 408-428-2500 Tel: (425) 702-8300
m

Fax: 805-496-6702 Tel: (410) 203-2317 Fax: 407-428-9000 Fax: (425) 702-8388
www.caintech.com Fax: (410) 203-2318 www.jsarep.com www.seaporttech.com
www.eaglesales.net
co

Cee-Jay Micro Ltd. The MacInnis Company Synergy Sales

Eastern Canada EK & Associates, Inc. ME, NH, RI, CT, MA, VT Representatives, Inc.
155 Terence Matthews Crescent IL, WI 375 Vanderbilt Avenue MN, ND, SD
e

Unit 2 887 E. Wilmette Road, Suite J Norwood, MA 02062 5401 Gamble Drive, Suite #105
Kanata, Ontario Paltine, IL 60074 Tel: (781) 762-8090 St. Louis Park, MN 55416
lin

Canada K2M 2A8 Tel: 847-776-1758 Fax: (781) 762-5059 Tel: (952) 544-1686
Tel: 613-599-5626 Fax: 847-776-8221 www.macinnis-company.com Fax: (952) 545-2935
www.cjmicro.com www.ekrep.com www.synergyreps.com
on

MINK Associates
CentraMark Technical Sales Electronic Representatives, Inc. NE, KA, MO Westrep Arizona
Associates IN, OH, MI, KY, West PA 10100 Santa Fe, Suite 311 AZ, NM, Clark County, NV &
TX, OK and LA 6801 Lake Plaza Drive, Suite D402 Overland Park, KS 66212 El Paso, TX
3333 Naaman School Road Indianapolis, IN 46220 Tel: (913) 341-8309 6105 S. Ash Avenue, Suite A8
Garland, TX 75040 Tel: (317) 915-1414 Fax: (913) 341-2605 Tempe, AZ 85283
Tel: 972-414-8188 Fax: (317) 915-1216 www.minkassoc.com Tel: (480) 820-9932
Fax: 972-414-6788 www.electronicreps.com Fax: (480) 820-9962
www.cmatex.com Precision Marketing Incorporated www.westrepaz.com
Essig & Associates, Inc. MS, AL, TN, GA,NC and SC
Comp-Tech Sales Iowa 5497 Wiles Road, Suite 204
Northern New Jersey, Metro New 809 N. Compton Drive Coconut Creek, FL 33073
York, Long Island Hiawatha, IA 52233 Tel: (954) 752-1700
232 Boulevard, Suite 11 Tel: (319) 363-8703 Fax: (954) 973-6335
Hasbrouck Heights, NJ 07604 Fax: (319) 363-7224 www.precision-marketing.com
Tel: (201) 288-7400 www.essigassoc.com
Fax: (201) 288-7583 RPI-Apex Associates, Inc.
www.comp-techsales.com HHP Associates, Inc. Upstate New York
Florida (excluding Long Island)
1355 S. International Pkwy, Suite 2471 54 Andover Street
Lake Mary, FL 32746 Andover, MA 01810
Tel: 407-829-8792 Tel: 978-475-7055
Fax: 407-829-8798 Fax: 978-475-4749
www.hhpai.com www.rpi-apex.com

© 2010 TELEDYNE RELAYS SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 49

 HEADQUARTERS
12525 Daphne Ave.
Hawthorne, CA 90250
Phone: (323) 777-0077 or (800) 284-7007
Fax: (323) 241-1287
E-mail: [email protected]

www.teledynerelays.com

m
(800) 284-7007

co
s.
nt
EUROPE
ne

9-13 Napier Road

Wardpark North
po

Cumbernauld G68 OEF

Scotland UK
Phone: +44 (0) 1236 453 124
m

Fax: +44 (0) 1236 780 651

E-mail: [email protected]
co
e

www.teledyne-europe.com
lin

+44 (0) 1236 453 124

on

PRINTED IN U.S.A. TR1110