Quick Guide to Precision Measuring Instruments

Calipers
■ Nomenclature
Vernier Caliper
Screw, gib pressing
Inside measuring faces Locking screw
Gib, slider
Step measuring faces Screw, gib setting

Depth bar Beam Stop, slider

Depth bar

Inside jaws
Depth measuring faces
Outside jaws Thumbwheel Main scale
Slider
Depth groove Reference surface
Outside measuring faces
Vernier scale

Absolute Digimatic Caliper

Inside measuring faces
Slider
Step measuring faces Output connector
Locking screw
Beam
Depth bar

Inside jaws

Depth measuring faces

Main scale
Outside jaws
Reference surface
Thumb-roller
ZERO Set/ABSOLUTE button
Outside measuring faces

■ How to Read the Scale

(1)

Main scale Dial

(1) Vernier scale (1) Main scale (2)

(2)
(2)
(2) Graduation 0.05mm Graduation 0.01mm
(1) Main scale 16 mm (1) Main scale 16 mm
(2) Vernier 0.15 mm (2) Dial 0.13 mm
Reading 16.15 mm Reading 16.13 mm

■ Special Purpose Caliper Applications

Point jaw caliper Offset jaw caliper Depth caliper Blade jaw caliper

For uneven surface measurement For stepped feature measurement For depth measurement For diameter of narrow groove measurement

Quick Guide to Precision Measuring Instruments 16

■ Types of Vernier Scale ■ Moving Jaw Tilt Error
The Vernier scale is attached to the caliper’s slider and each division If the moving jaw becomes tilted out of parallel with the fixed jaw,
on this scale is made 0.05mm shorter than one main scale division either through excessive force being used on the slider or lack of
of 1 mm. This means that, as the caliper jaws open, each successive straightness in the reference edge of the beam, a measurement error
movement of 0.05mm brings the succeeding vernier scale line into will occur as shown in the figure. This error may be substantial due to
coincidence with a main scale line and so indicates the number of the fact that a caliper does not conform to Abbe’s Principle.
0.05mm units to be counted (although for convenience the scale is
numbered in fractions of a mm). Alternatively, one vernier division f=hθ=h·a/ℓ
may be made 0.05mm shorter than two divisions of the main scale to

a
θ
make a long vernier scale. This makes the scale easier to read but the
principle, and resolution, is still the same.

h
h
f
● Standard Vernier scale (resolution 0.05mm)

Example: Assume that the error slope of the jaws due to tilt of the slider is 0.01mm in 50mm and
the outside measuring jaws are 40mm deep, then the error (at the jaw tip) is calculated as
(40/50)x0.01mm = 0.008mm.
If the guide face is worn then an error may be present even using the correct measuring
force.

Reading 1.45mm

● Long Vernier scale (resolution 0.05mm)

■ About Long Calipers
Steel rules are commonly used to roughly measure large workpieces
but if a little more accuracy is needed then a long caliper is suitable for
the job. A long caliper is very convenient for its user friendliness but
does require some care in use. In the first place it is important to realize
Reading 30.35mm
there is no relationship between resolution and accuracy. Resolution is
constant whereas the accuracy obtainable varies dramatically according
to how the caliper is used.
The measuring method with this instrument is a concern since distortion
of the main beam causes a large amount of the measurement error,
■ Sources of Error so accuracy will vary greatly depending on the method used for
Main sources of error include scale misreading (parallax effect), supporting the caliper at the time. Also, be careful not to use too much
excessive measuring force causing jaw tilt, thermal expansion caused by measuring force when using the outside measuring faces as they are
a temperature difference between the caliper and workpiece, and small- furthest away from the main beam so errors will be at a maximum here.
hole diameter error caused by inside jaw offset. There are other minor This precaution is also necessary when using the tips of the outside
error sources such as graduation accuracy, reference edge straightness, measuring faces of a long-jaw caliper.
main scale flatness and squareness of the jaws. These sources are
allowed for within the specified accuracy of a new caliper and only
cause significant error in case of wear or damage.
The JIS standard emphasizes that care must be used to ensure that
measurement is performed with an appropriate and constant measuring ■ Inside Measurement with a CM-type
force, since a caliper has no constant-force device, and that the user Caliper
must be aware of the increased possibility of error due to measuring a Because the inside measuring faces of a CM-type caliper are at the
workpiece using the tips of the jaws (Abbe’s Principle). tips of the jaws the measuring face parallelism is heavily affected by
measuring force, and this becomes a large factor in the measurement
accuracy attainable.

In contrast to an M-type caliper, a CM-type caliper cannot measure a

very small hole diameter because it is limited to the size of the stepped
jaws, although normally this is no inconvenience as it would be unusual
CM-type caliper CN-type caliper (with knife-edge)
to have to measure a very small hole with this type of caliper. Of course,
the radius of curvature on the inside measuring faces is always small
enough to allow correct hole diameter measurements right down to the
lowest limit (jaw closure).

Mitutoyo CM-type calipers are provided with an extra scale on the slider
for inside measurements so they can be read directly without the need
for calculation, just as for an outside measurement. This useful feature
eliminates the possibility of error that occurs when having to add the
For outside measurement For outside measurement inside-jaw-thickness correction on a single-scale caliper.
For measurement of inside bore For stepped feature measurement

17 Quick Guide to Precision Measuring Instruments