DIgSILENT PowerFactory

Technical Reference Documentation

Series Capacitor
ElmScap
 DIgSILENT GmbH

Heinrich-Hertz-Str. 9
72810 - Gomaringen
Germany

T: +49 7072 9168 0

F: +49 7072 9168 88

http://www.digsilent.de
[email protected]
Version: 2016
Edition: 1

Copyright © 2016, DIgSILENT GmbH. Copyright of this document belongs to DIgSILENT GmbH.
No part of this document may be reproduced, copied, or transmitted in any form, by any means
electronic or mechanical, without the prior written permission of DIgSILENT GmbH.

Series Capacitor (ElmScap) 1

Contents

Contents

1 General Description 3

2 Load Flow Analysis 4

2.1 AC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.2 DC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3 Short-Circuit Analysis 4

3.1 AC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4 RMS-Simulation 5

4.1 AC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4.2 DC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

5 EMT-Simulation 5

5.1 AC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

5.1.1 Without Metal Oxide Varistor Protection . . . . . . . . . . . . . . . . . . . 5

5.1.2 With Metal Oxide Varistor Protection . . . . . . . . . . . . . . . . . . . . . 6

5.1.3 Spark Gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

5.2 DC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6 Harmonics/Power Quality 8

6.1 Frequency-Dependent Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 8

A Signals Definitions 9

B Parameter Definitions 10

List of Figures 12

List of Tables 13

Series Capacitor (ElmScap) 2

1 General Description

1 General Description

PowerFactory provides both an AC and a DC series capacitor model. The AC series capacitor
model may be used for various applications which require the connection of the series capaci-
tance to an AC terminal, such as:

• Series compensation of transmission lines

• Filter capacitance

The DC series capacitor model may be used for applications which require connection to a DC
terminal, such as:

• Detailed voltage source converter modelling

• FACTS controller modelling

The model uses a nonlinear resistance in parallel with the capacitance for modelling protection
of series capacitances by a MOV-bypass. Under normal operating conditions, it is assumed that
the parallel resistance has no influence on the capacitance. It is therefore only considered in
EMT simulations.

The rated voltage and rated current (or rated power) can be specified, as well as a Thermal
Rating. The System Type can be set to either AC or DC and the Phases to either 1 or 3.
The three-phase model is illustrated in Figure 1.1, and the single-phase model is illustrated in
Figure 1.2. When using the three-phase model in conjunction with the Unbalanced option on
the Load Flow tab of the series capacitor element dialog, the user may specify a susceptance
on a per-phase basis.

U12

bus 1:A bus 2:A

i

bus 1:B bus 2:B

bus 1:C bus 2:C

Figure 1.1: Three-phase model

U12

bus 1 bus 2
i
Figure 1.2: Single-phase model

Series Capacitor (ElmScap) 3

3 Short-Circuit Analysis

2 Load Flow Analysis

2.1 AC Model

In all steady-state analysis functions the capacitance is modelled by its nominal frequency be-
haviour:

I = jωn CU 12 (1)

2.2 DC Model

Under pure DC conditions, a capacitance represents an open-circuit, hence:

I=0 (2)

3 Short-Circuit Analysis

3.1 AC Model

In all steady-state analysis functions the capacitance is modelled by its nominal frequency be-
haviour as described by (1).

The series capacitor is bypassed for the calculation of the R/X ratio in the following cases:

• When the equivalent frequency method is used by the calculation (see Note below).
• When using the ANSI method:

1. If the parameter X/R Calculation on the Advanced Options tab (as shown in the Short-
Circuit command dialog in Figure 3.1) is set to Separate R and X ;
2. If the parameter X/R Calculation on the Advanced Options tab is set to complex,
then the bypassing is dependent upon the setting of the Bypass Series Capacitance
option, explained in item 3., below;
3. If the parameter Bypass Series Capacitance (also on the Advanced Options tab) is
set to:
– All currents
– LV & Interrupting & 30 cycle current (bypass only in calculation of these kinds of
current values)
– 30 cycle currents (bypass only in calculation of these kinds of current values)

Note: the equivalent frequency method is used by the calculation when the user has selected
the Method on the Basic Options tab of the Short-Circuit command to be one of:

• VDE0102 or IEC60909 and has set the Using Method option (on the Advanced Options
tab) for the calculation of the peak short-circuit current, ip, to either C(1) or C(012); and
the peak breaking current, ib, to C or C’; or

Series Capacitor (ElmScap) 4

5 EMT-Simulation

• complete and has set the Using Method option (on the Advanced Options tab) for the
calculation of the peak short-circuit current, ip, the peak breaking current, ib, and the dc
short-circuit current, idc, to either C(1) or C(012).

Figure 3.1: ANSI Short-Circuit calculation (Advanced Options tab)

4 RMS-Simulation

4.1 AC Model

The RMS-simulation and the Load Flow calculation both use the same circuit model represen-
tation of the series capacitance. Please refer to Section 2.1.

4.2 DC Model

In DC circuits, network transients are taken into consideration. The series capacitance is there-
fore modelled by the differential equation of a capacitance:

du12
i(t) = C (3)
dt

5 EMT-Simulation

5.1 AC Model

5.1.1 Without Metal Oxide Varistor Protection

For EMT simulation, without any Metal Oxide Varistor (MOV) protection, the series capacitance
is therefore modelled by the differential equation of a capacitance:

Series Capacitor (ElmScap) 5

5 EMT-Simulation

du12 (t)
i(t) = C (4)
dt

5.1.2 With Metal Oxide Varistor Protection

When the option Metal Oxide Varistor is selected, a nonlinear resistance can be defined which
represents the protection of series capacitances by the MOV. The nonlinear resistance is en-
tered by a voltage-current characteristic table. The entire characteristic is then approximated
using cubic splines. The corresponding equivalent circuit diagram is shown in Figure 5.1. An
example of a typical MOV characteristic is shown in Figure 5.2.

U12

iMOV

bus 1 bus 2
i1 ic
Figure 5.1: Series capacitance with MOV protection

Figure 5.2: Typical MOV characteristic

The model equations of the series capacitance with MOV protection are:

iM OV (t) = f (u12 (t)) (5)

du12
ic (t) = C (6)
dt

Series Capacitor (ElmScap) 6

5 EMT-Simulation

i1 = iM OV + ic (7)
The dissipated MOV energy is calculated as follows:
pM OV (t) = iM OV (t) · uM OV (t) (8)

Z t
EM OV (t) = pM OV (τ )dτ (9)
tstart

5.1.3 Spark Gap

The series capacitor model for EMT simulations allows the definition of a protection spark gap,
via the selection of the Spark Gap option. Once this option is selected, the resistance and
reactance of the damping circuit can be defined. The spark gap model with optional parallel
MOV surge arrester is shown in Figure 5.3.

Figure 5.3: Spark gap model

External Tripping
When the option Built-In Tripping Unit is deactivated, the spark gap can be triggered via the
use of input signals inSg A, inSg B and inSg C (defined in Table A.1) using either a param-
eter event (EvtParam) defined for the EMT simulation, or via an external DSL controller. The
surge arrester is described in detail in the PowerFactory Surge Arrester Technical Reference
document.

Built-In Tripping Unit

By activating the option Built-In Tripping Unit, it is possible to specify when to trigger the spark
gap, according to any of the following thresholds:

Series Capacitor (ElmScap) 7

6 Harmonics/Power Quality

• Trip when Current value is above the specified value in kA

• Trip when Voltage value is above the specified value in kV . Available only for option Metal
Oxide Varistor deactivated.
• Trip when Energy value is above the specified value in M W . Available only for option
Metal Oxide Varistor selected.

• Trip when Power value is above the specified value in M W . Available only for option Metal
Oxide Varistor selected.

Concurrent Tripping
The triggering of the models can be done concurrently by the built-in tripping conditions as
well as by using the external signals.

5.2 DC Model

In DC systems, the EMT model is identical to the RMS model. The DC model does not consider
nonlinear resistance.

6 Harmonics/Power Quality

6.1 Frequency-Dependent Characteristics

Frequency-dependent characteristics may be defined for the capacitance (parameter names

follow in parentheses): C (ccap), or in the case of a series capacitor set to Unbalanced, the
capacitance C per-phase (ccap a, ccap b and ccap c).

Note: For absolute characteristics, the values defined in the element (not in the characteristic)
will be used at the fundamental frequency. In addition, for an Unbalanced capacitor, only relative
characteristics may be defined (i.e. not characteristics which are set to use absolute values).

Series Capacitor (ElmScap) 8

A Signals Definitions

A Signals Definitions

Table A.1: Internal signals (EMT-Simulation)

Variable Unit I/O Description Symbol

Emov a MWs STATE MOV absorbed energy
Emov b MWs STATE MOV absorbed energy
Emov c MWs STATE MOV absorbed energy
inSg A IN Spark Gap
inSg B IN Spark Gap
inSg C IN Spark Gap

Series Capacitor (ElmScap) 9

B Parameter Definitions

B Parameter Definitions

Table B.1: Input parameters for series capacitor element

Parameter Unit Default Description Range Symbol

Value
loc name Name
bus1 Terminal i (StaCubic)
bus1 bar Terminal i
bus2 Terminal j (StaCubic)
bus2 bar Terminal j
iZoneBus 0 Zone
cpZone Zone
iAreaBus 0 Area
cpArea Area
outserv 0 Out of Service x≥0 and
x≤1
ucn kV 1, Ratings: Rated Voltage x≥0
Sn MVA 1,732051 Ratings: Rated Power x>0
Curn kA 1, Ratings: Rated Current x>0
pRating Thermal Rating (IntThrat-
ing)
systp AC System Type AC:DC
nphases 3 Phases 1:3
Inom kA 1, Rated Current
i sym 0 Balanced/Unbalanced x=0 or x=1
ccap F 0, Value: Capacitance, C x≥0 C
bcap S 0, Value: Susceptance, B x≥0
xcap Ω 0, Value: Reactance 1/B x≥0
bcap a S 0, Value / Phase A: Suscep- x≥0
tance, B
ccap a F 0, Value / Phase A: Capaci- x≥0
tance, C
xcap a Ω #INF Value / Phase A: Reac- x≥0
tance 1/B
bcap b S 0, Value / Phase B: Suscep- x≥0
tance, B
ccap b F 0, Value / Phase B: Capaci- x≥0
tance, C
xcap b Ω #INF Value / Phase B: Reac- x≥0
tance 1/B
bcap c S 0, Value / Phase C: Suscep- x≥0
tance, B
ccap c F 0, Value / Phase C: Capaci- x≥0
tance, C
xcap c Ω #INF Value / Phase C: Reac- x≥0
tance 1/B
maxload % 100, Thermal Loading Limit: x≥0
Max. Loading
iSparkGap 0 Spark Gap x=0 or x=1
Rdamp Ω 0, Spark Gap Damping Cir- x≥0 Rdamp
cuit: Resistance
Xdamp Ω 0, Spark Gap Damping Cir- x≥0 Xdamp
cuit: Reactance
i enter 0 Metal Oxide Varistor x=0 or x=1
Im kA 0, Current IM OV

Series Capacitor (ElmScap) 10

B Parameter Definitions

Vm kV 0, Voltage

Table B.2: Input parameters for series capacitor element

Parameter Unit Default Description Range Symbol

Value
iInterPol 0 Interpolation spline:-
piecewise
linear
smoothfac % 10, Smoothing Factor x≥0.0 and
x≤100.0
gnrl modif 01.01.1970 Object modified
01:00:00
gnrl modby Object modified by
sernum Serial Number
manuf Manufacturer
constr 0 Year of Construction
iComDate 01.01.1970 Commissioning Date
01:00:00
chr name Characteristic Name
for name Foreign Key
dat src MAN Data source
doc id Additional Data ()
pOwner Owner (ElmOwner)
pOperator Operator (ElmOperator)
desc Description
appr status Not Ap- Approval Information:
proved Status
appr modif 01.01.1970 Approval Information:
01:00:00 Modified
appr modby Approval Information:
Modified by
cimRdfId RDF ID

Series Capacitor (ElmScap) 11

List of Figures

List of Figures

1.1 Three-phase model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.2 Single-phase model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.1 ANSI Short-Circuit calculation (Advanced Options tab) . . . . . . . . . . . . . . . 5

5.1 Series capacitance with MOV protection . . . . . . . . . . . . . . . . . . . . . . . 6

5.2 Typical MOV characteristic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5.3 Spark gap model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Series Capacitor (ElmScap) 12

List of Tables

List of Tables

A.1 Internal signals (EMT-Simulation) . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

B.1 Input parameters for series capacitor element . . . . . . . . . . . . . . . . . . . . 10

B.2 Input parameters for series capacitor element . . . . . . . . . . . . . . . . . . . . 11

Series Capacitor (ElmScap) 13