0% found this document useful (0 votes)

53 views

Mesh Control

Mesh_Control IN ANSYS

Uploaded by

Ranjeet Singh

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

53 views

Mesh Control

Mesh_Control IN ANSYS

Uploaded by

Ranjeet Singh

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 60

Module 05: Mesh Control

Introduction to ANSYS Mechanical

Release 18.0

1 © 2016 ANSYS, Inc. April 4, 2017

Module 05 Topics
This module covers introductory topics for meshing and mesh control:

1. Meshing in Mechanical 8. Workshop 05.1: Mesh Creation

2. Global Mesh Controls 9. Workshop 05.2: Mesh Control
3. Local Mesh Controls 10. Appendix 05.1: Mesh Quality Criteria
4. Troubleshooting 11. Appendix 05.2: Model Assembly
5. Virtual Topology
6. Direct Meshing
7. Mesh Quality Criteria

2 © 2017 ANSYS, Inc. April 4, 2017

05.01 Meshing in Mechanical
The nodes and elements representing the geometry model make up the mesh:
− A “default” mesh is automatically generated during a solution.
− It is generally recommended that additional controls be added to the default mesh
before solving.
− A finer mesh produces more precise answers but also increases CPU time and memory
requirements.

Generate the mesh or preview the surface of the

mesh before solving (previewing the surface mesh is
faster than generating the entire mesh).

3 © 2017 ANSYS, Inc. April 4, 2017

05.02 Global Mesh Controls
Physics-Based Meshing allows the user to specify the
metrics used in measuring element quality to be
based on the kind of analysis being done.
Physics preferences are:
− Mechanical
− Nonlinear Mechanical
− Electromagnetics
− CFD
− Explicit
− Hydrodynamics
Different analysis types define acceptable or
favorable element shapes differently. For this course
we limit the discussion to Mechanical.

4 © 2017 ANSYS, Inc. April 4, 2017

05.02 Global Mesh Controls
• Relevance is the most basic global size control and is set in the “Defaults”
area of the mesh details.
• Relevance is set between –100 and +100 (zero = default).

− Relevance = coarse mesh + Relevance = fine mesh

5 © 2017 ANSYS, Inc. April 4, 2017

05.02 Global Mesh Controls
Sizing Control:
− The points below assume that Size Function is set to
“Adaptive.” (Size Function is discussed further on the next
slide.)
− Relevance Center sets the midpoint of the “Relevance”
global control.
− Element Size defines the maximum element size used for the
entire model.
− For most static structural applications, the default values for
the remaining global controls are usually adequate.

Relevance Center
Medium
Coarse Fine
0 0
-100 +100 -100 +100

6 © 2017 ANSYS, Inc. April 4, 2017

05.02 Global Mesh Controls
Size Function provides several advanced automated
control options over the global mesh sizing. It is
controlled in the Mesh Details view.
• While many of these controls are beyond the scope of
an introductory course, we’ll review some of the
advanced size controls here. As stated earlier, linear
static analysis types usually do not share the same
meshing demands as more advanced analysis types,
and so advanced size controls are not often necessary.
• “Adaptive” is the default setting for the Mechanical
Physics Preference, and provides the highest level of
automation.
• Four advanced size functions can be employed:
Proximity and Curvature, Curvature, Proximity, and
Uniform.

7 © 2017 ANSYS, Inc. April 4, 2017

05.02 Global Mesh Controls
The Uniform Size Function provides control based solely on the user-input parameters Min
Size, Max Face Size, Max Tet Size, and Growth Rate.
The Curvature Size Function, as the name implies, is driven by the curvature encountered
in the geometry: the higher the curvature, the higher the mesh density. For models
dominated by lots of curved features this control provides a way to refine the mesh over
much of the model without using numerous local controls. For models composed of mostly
straight features, this control will have a lesser impact.

Curvature On Curvature Off

8 © 2017 ANSYS, Inc. April 4, 2017
05.02 Global Mesh Controls
The Proximity Size Function provides a means to control the mesh density in regions of the
model where features are located more closely together. In cases where the geometry
contains a number of such regions, this control provides a way to refine the mesh over much
of the model without using numerous local controls.
As mentioned above, proximity and curvature can be combined.

Num Cells = 4 Num Cells = 12

9 © 2017 ANSYS, Inc. April 4, 2017

05.02 Global Mesh Controls
Element Midside Nodes:
− Program Controlled (default), Dropped, or Kept (see below).
Error Limits for the “Mechanical” Physics Preference:
− Standard Mechanical is recommended for linear stress,
modal, and thermal analyses.
− Aggressive Mechanical is recommended for analyses
involving large deformations and/or material nonlinearities.
Number of Retries: If poor quality elements are detected, the
mesher will try again using finer mesh controls. This setting
limits the number of possible retries.

Element A Element B

Kept Dropped

10 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Local Mesh Controls can be applied to either a Geometry Selection or a Named
Selection. These are available only when the mesh branch is highlighted. Some
of the available controls include :
− Method Control
− Sizing Control
− Contact Sizing Control
− Refinement Control
− Face Meshing Control
− Inflation Control
− Pinch Control

11 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Method Control: provides the user with options for the
meshing algorithm to be used.
Method = Automatic (default):
− Body will be swept if possible, which results in either all or most of
the elements being hexahedral. If a swept mesh is not possible, the
“Patch Conforming Tetrahedron” mesher will be used. Both of
these methods are discussed further in subsequent slides.

12 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
• Mesh Methods for 3D bodies:
– Automatic
– Tetrahedrons
• Patch Conforming
• Patch Independent
– MultiZone
– Hex Dominant
– Sweep
• Mesh Methods for 2D bodies:
– Automatic Method (Quad Dominant)
– Triangles
– Uniform Quad/Tri Triangle (Tri) Quadrilateral (Quad)
– Uniform Quad

13 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Method = Tetrahedrons:
− An all-tetrahedron mesh is generated.
− Can use Patch Conforming or Patch Independent Meshing algorithms.

Patch Conforming
Underlying Geometry
Patch Independent

14 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Method = Hex Dominant: Creates a free hex-dominant mesh
• Recommended for meshing bodies with large interior
volumes.
• Not recommended for thin or highly complex shapes.
• Useful for meshing bodies that cannot be swept.

Solid Model with Hex dominant mesh

(approximate percentages):
Tetrahedrons – 443 (9.8%)
Hexahedron – 2801(62.5%)
Wedge – 124 (2.7%)
Pyramid – 1107 (24.7%)

15 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Method = Sweep (hex and possibly wedge shapes):
− Source/Target Selection: Manually select the start/end faces for sweeping or allow
the mesher to choose.
− Can include size controls and/or biasing along sweep.

Source

Note: the geometry shown here has six

different possible sweep directions.
Target
16 © 2017 ANSYS, Inc. April 4, 2017
05.03 Local Mesh Controls MultiZone Mesh
Method = MultiZone:
• Based on blocking approach used in ANSYS ICEM CFD Hexa
• Automatically decomposes geometry
• Uses structured and unstructured blocks
• Can have multiple source and target faces
• Depends on settings of Free Mesh Type
• Structured blocks are meshed with Hexa or Hexa/Prism
• If Free Mesh Type is set to other than Not Allowed, then
unstructured blocks are meshed with Tetra, Tetra/Pyramid,
Hex Dominant, or Hex Core, based on the selected method
• Program Controlled inflation

17 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Method = MultiZone—Controls:
– Src/Trg Selection = Automatic

Geometry for MultiZone Details View of MultiZone MultiZone Mesh

Meshing Method

18 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Method = MultiZone—Controls:
– Src/Trg Selection = Manual

Geometry for MultiZone Details View of MultiZone Cut section of MultiZone

Meshing Method Mesh

19 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Method = MultiZone—Controls:
– Free Mesh Type = Tetra,
Tetra/Pyramid, Hexa
Dominant, or Hexa Core Type: Tetra

Type: Tetra/Pyramid

Type: Hexa Dominant

Geometry

Type: Hexa Core

20 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Method = MultiZone—Controls:
– Local Defeaturing Tolerance
Sliver face
captured in
mesh
No Defeaturing

Geometry with a Sliver face

sliver face ignored in
mesh
Using Defeaturing

– Can be also controlled with global defeaturing tolerance

21 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Surface Body Methods:
− Quadrilateral Dominant (default): attempts to
mesh with as many quadrilateral elements as
possible, fills in with triangles.

− Triangles: all triangular shapes are used.

− MultiZone Quad/Tri: Depending on settings, quad

or tri shapes are created using a patch
independent algorithm.

Note: Each method contains a unique set of options in

the details allowing additional configuration.
22 © 2017 ANSYS, Inc. April 4, 2017
05.03 Local Mesh Controls
Sizing:
− Element Size (element edge length)
− Number of Divisions
− Sphere of Influence (see next slide)
“Soft” control may be overridden by other mesh controls, “Hard” may not.

Entity Element Size # of Elem. Division Sphere of Influence

Bodies x x
Faces x x
Edges x x x
Vertices x

23 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Sizing—Sphere of Influence:
− Center is located using a coordinate system.
− All scoped entities within the sphere are affected by size settings.
− Only the portion of the scoped face or body within the sphere is
included in the scope of the mesh control.

24 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Contact Sizing: generates similarly-sized elements on
contact faces for face/face or face/edge contact regions.
− “Element Size” or “Relevance” can be specified.
− Can drag and drop a Contact Region object onto the “Mesh”
branch as a shortcut.

25 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Refinement:
− An initial mesh is created using the global and local size settings, then elements are
divided at the scoped locations (up to 3 times).

Note: The refinement method generally offers less control and/or predictability over the final mesh, since
the initial mesh is simply split. This splitting process may adversely affect other meshing controls.

26 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Mapped Face Meshing: generates structured meshes on surfaces

Mapped quad or tri mesh also available for surface bodies.

27 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Mapped Face Meshing:
• For some geometry mapping will fail if an obvious pattern is not recognized.
• By specifying side, corner or end vertices a mapped face can be achieved.

Original mapping failed as indicated By specifying side and end vertices, the
by the status icon. mapped face mesh succeeds.

28 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Inflation: useful for adding layers of prismatic elements along specific boundaries.

Note: Inflation is used more often in CFD and EMAG applications, but may occasionally
be useful for capturing stress concentrations etc. in structural applications.

29 © 2017 ANSYS, Inc. April 4, 2017

05.03 Local Mesh Controls
Pinch: allows the removal of small features by “pinching” out small
edges and vertices.
− Master: geometry that retains the original geometry profile.
− Slave: geometry that changes to move toward the master.
− Can be automatic (mesh branch details) or local (add Pinch branch).

30 © 2017 ANSYS, Inc. April 4, 2017

05.04 Troubleshooting
Mesh Metrics
• Requested in the “Quality” section
• Select individual bars in the graph to view the
elements graphically.

Mesh metrics are described further Section 05.07 “Mesh Quality Criteria” and in
Appendix 05.1 “Mesh Quality Criteria.”

31 © 2017 ANSYS, Inc. April 4, 2017

05.04 Troubleshooting
If the mesher is not able to generate a mesh, an error message will be returned.
− Double-click the message field in the status bar to open the messages window.
− Double-click individual messages to show the complete error text in a separate window.

When possible, Mechanical will

graphically display the problem
region(s)—select the message in the
message window, then RMB > Show
Problematic Geometry. Using the
wireframe view will make finding
these areas easier.

32 © 2017 ANSYS, Inc. April 4, 2017

05.04 Troubleshooting
The mesher also provides visual cues to identify obsolete and/or failed
meshes. As shown in the figures below, failed meshes are shaded in
maroon and obsolete meshes are shaded in yellow.

33 © 2017 ANSYS, Inc. April 4, 2017

05.05 Virtual Topology
Virtual topology is a feature that can aid you in reducing the number of elements in the model,
simplifying small features out of the model, and simplifying load abstraction. The “Virtual
Topology” branch is added below the “Model” branch.

• For meshing certain CAD models you may want to group faces and/or edges together allowing
you to form virtual cells in order to reduce or improve the elements.
• You can split a face to create two virtual faces, or split an edge to create two virtual edges for
improved meshing.
• Virtual Cells can be created automatically.

34 © 2017 ANSYS, Inc. April 4, 2017

05.05 Virtual Topology
In this example, one edge of this multibody part
has a size control assigned which causes
irregularities in the overall mesh.
Virtual Split Edges

Initial Mesh

Size Control
In the figure at upper right, 3 edges are Final Mesh
“virtually” split to produce improved
elements shapes.
35 © 2017 ANSYS, Inc. April 4, 2017
05.05 Virtual Topology
Surface Model Example:

Virtual Cell

36 © 2017 ANSYS, Inc. April 4, 2017

05.05 Virtual Topology

A “Virtual Topology” branch is added below the “Model” branch:

− Individual virtual entities do not appear in the tree. Instead, a
statistics section in the details lists virtual entities.
− Virtual Cells can be created manually:
• Select the entities to be included in the virtual cell.
• Choose “Merge Cells” in the context menu (or RMB > Insert
> Virtual Cell)
− Virtual Cells can be created automatically:
• Low, Medium, High: Indicates how aggressively virtual
topology will be searched for.
• Edges Only: Searches for adjacent edges to be combined.
• Custom: users have control on specific options

37 © 2017 ANSYS, Inc. April 4, 2017

05.05 Virtual Topology
In some instances it may be desirable to modify
topology to allow application of some desired effect
(e.g., mesh control, load, support, …):
• Split face at vertices (preselect the desired vertices)

• Split Edge (preselect the desired edge)

• Add a hard vertex (preselect the face at the desired

vertex location)

38 © 2017 ANSYS, Inc. April 4, 2017

05.05 Virtual Topology
Virtual entities can be reviewed, edited or deleted from the
context toolbar (highlight Virtual Topology branch):
− Use the arrow keys to cycle through next/previous virtual
entities.
− The virtual entity is highlighted graphically and the status
bar (bottom of graphics window) indicates the current
selection.
− The Edit icon allows access to an editor window where
modifications to the virtual entity definition can be made.
− Use “Delete” to remove unwanted virtual entities.

39 © 2017 ANSYS, Inc. April 4, 2017

05.05 Virtual Topology
Keep in mind that the underlying “real” topology can change!
Example: a chamfer is included along with the top surface in this virtual cell.
The interior lines are not recognized anymore.
The resulting element’s edge is shown as a solid line
Original mesh and the original chamfer and top surface is shown
as a dotted line.
The chamfer representation is no longer present.

Mesh with virtual topology

40 © 2017 ANSYS, Inc. April 4, 2017

05.06 Direct Meshing
Bodies can be meshed/remeshed individually in any desired order
• Subsequent bodies will use the attached face mesh
• The meshing results will depend on the meshing order
• RMB on the body/bodies to generate the mesh locally
Meshing first
Automated the block then
Meshing first
meshing the pipe
the pipe then
the block

Wedges
Hexas Hexas

41 © 2017 ANSYS, Inc. April 4, 2017

05.07 Mesh Quality Criteria
You can check mesh quality using
Mesh Metrics.
Remember: Each physics type has its
own quality criteria.

42 © 2017 ANSYS, Inc. April 4, 2017

05.07 Mesh Quality Criteria
The Mesh Details Display Style option can be used to display the
mesh color-coded by the various mesh quality measures:

05.07 Mesh Quality Criteria
Example mesh metric : Element Quality
This metric is based on the ratio of the volume to the edge length
for a given element.

0 1
Bad Perfect

05.07 Mesh Quality Criteria

For additional information on mesh metrics, see

Appendix 05.1: Mesh Quality Criteria

05.08 Workshop 05.1: Mesh Creation

Goal:
Use the various mesh controls to mesh a small assembly.

05.09 Workshop 05.2: Mesh Control

Goal:
Use the various mesh controls to enhance the mesh for a small assembly.

05.10 Appendix 05.1