Indian Space Research Organisation - Department of Space

NIT No. VSSC/CMG/CPH/14/2018-19 Dt. 18.12.2018

Name of work: Construction of Rocket Launch Viewing Shelter near Space Museum at TERLS, VSSC, Thumba (Civil works)
SCHEDULE OF QUANTITIES
Name Of Contractor
Item No Quantity Description of Item Unit Rate Rate in words Amount in (Rs.)
PART A : SHELTER WORKS
A01 100.00 Clearing Jungle including uprooting of rank vegetation, SQM
grass, brush wood, trees and sapplings of girth up to
30cm measured at a height of 1 m above ground level
and removal of rubbish up to a distance of 50 m outside
the periphery of the area cleared. (Note: If however, only
grass is met with, the area will be measured and paid for,
under as a separate item)

A02 745.00 Earthwork in excavation for FOUNDATION TRENCHES in CUM

ALL KINDS OF SOILS including dressing of sides,
ramming of bottom, disposing the surplus excavated
materials within a distance of 50m and lift 1.50m complete
as per specifications. (Disposed soil to be levelled by
breaking clods if any and neatly dressed).

A03 1907.40 Filling available excavated approved earth (excluding CUM

rock) in trenches, sides of foundations, plinth, etc; in
layers not exceeding 15cms depth breaking clods,
consolidating each deposited layer by ramming, watering
and dressing, etc; complete for lead up to 150m and all
lifts etc., complete as per specifications.

A04 Providing and laying cement concrete using 40mm .

nominal size graded hard granite stone aggregate
obtained from approved quarry including compaction,
finishing top surface to level, curing but excluding cost of
formwork, etc; complete as per specifications. Mix ratio
specified is for (cement: Graded Manufactured Sand:
graded stone aggregate).

182.00 i) In foundation and plinth/sub-base to floors with P.C.C CUM

1:5:10

A05 Providing and Constructing solid Cement Concrete block

masonry in Cement Mortar 1:6 (1 cement : 6
Manufactured Sand) using factory made, load bearing,
approved quality Cement Concrete blocks of specified
size, Grade A as per IS:2185 (Part II)-2005, Density of
blocks not less than 1500 kg/cum. Minimum average
Compressive strength of units - 4.0 N/sqmm and
Minimum strength of individual units 3.2N/sqmm, setting
in position, curing, raking out joints wherever required
etc., complete with all leads and all as per specifications
and directions of the Engineer-in-charge. IN
FOUNDATION AND PLINTH.

61.00 i) For 200mm thick walls using (400x200x200) mm size CUM

blocks.

Page 1
Item No Quantity Description of Item Unit Rate Rate in words Amount in (Rs.)
A06 Providing and Constructing Solid Cement concrete block
masonry in Cement mortar 1:6 (1 cement : 6
Manufactured Sand) using factory made, load bearing,
approved quality, Grade A as per IS:2185 (Part II)-2005,
Density of blocks not less than 1500kg/cum Minimum
average Compressive strength of units 4.0N/sqmm and
Minimum strength of individual units 3.2N/sqmm, set to
level plumb including setting in position, providing
scaffolding, curing, raking out joints wherever required
etc., complete with all leads and all as per specification
and directions of the Engineer-in-charge. IN
SUPERSTRUCTURE UPTO 3.50M FROM FFL OF GF.

` 35.00 i) For 200mm thick walls using (400x200x200)mm size CUM

blocks.

A07 210.00 Providing & laying in position machine batched, machine CUM
mixed and machine vibrated design mix cement concrete
of specified grade for reinforced cement concrete
structural elements, using graded hard granite stone
aggregates of maximum 20mm nominal (down graded)
size obtained from approved quarry including fine
aggregates conforming to latest IS 383 and cement all as
per approved design mix proportions conforming to latest
IS 10262 with minimum cement content for durability
including supplying and providing concrete cover blocks
etc., which shall be followed as per latest IS:456-2000
including mixing, transporting, placing, vibrating,
compaction, finishing to required levels, curing etc.,
complete all as per specifications but excluding cost of
form work and steel reinforcement. Rate to include labour
for keeping embedments if any wherever required while
casting. Rate also to include lift charges and scaffolding
for all depths/ levels from FFL / GL.

The design mix proportions shall clearly indicate cement :

Graded Manufactured Sand : coarse aggregate : water
cement ratio and approval shall be obtained from
Engineer-in- charge for initial and subsequent mixes as
and when there will be change in quarry / materials for M-
30 grade reinforced cement concrete, etc. all work up to
plinth level.

A08 Providing & laying in position machine batched, machine .

mixed and machine vibrated design mix cement concrete
of specified grade for reinforced cement concrete
structural elements, using graded hard granite stone
aggregates of maximum 20mm nominal (down graded)
size obtained from approved quarry including fine
aggregates conforming to latest IS 383 and cement all as
per approved design mix proportions conforming to latest
IS 10262 with minimum cement content for durability
including supplying and providing concrete cover blocks
etc., which shall followed as per latest IS:456-2000
including mixing, transportation, placing, vibrating,
compaction, finishing to required levels, curing etc.,
complete all as per specifications but excluding cost of
form work and steel reinforcement. Rate to include labour
for keeping embedments if any wherever required while
casting. Rate also to include lift charges and scaffolding
for the heights for the levels indicated below from
FFL/GL.

Page 2
Item No Quantity Description of Item Unit Rate Rate in words Amount in (Rs.)
The design mix proportion shall clearly indicate cement
:Graded Manufactured Sand : coarse aggregate : water
cement ratio and approval shall be obtained from
Engineer-in-charge for initial and subsequent mixes as
and when there will be change in quarry / materials for M-
30 grade reinforced cement concrete,etc., all work above
plinth level upto the levels indicated below from FFL of
GF.

I) Walls (any thickness) including attached pilasters,

buttresses, plinth and string courses, fillets, columns,
pillars, piers, abutments, posts and struts, etc.,

48.00 i) Upto 3.50m level from FFL CUM

8.00 ii) Above 3.50m level to 6.00m level from FFL CUM

116.00 II) Beams, suspended floors, roofs having slope up to 15 CUM

degree, landings, balconies, shelves, chajja, lintels,
bands, plain window sills, staircases and spiral stair
cases etc.,

A09 Providing rigid and water tight centering and shuttering .

using best quality wood/ plywood/ steel forms and
centering with steel props, acro tubes etc.The centering
(vertical props, bracings etc.) shall be of steel tubes with
or without extension pieces or built-up section of rolled
steel, including strutting, propping, bracing, staging etc.,
complete for all RCC items fixed in position as required
including labour for careful removal of form work etc.,
complete all as per specifications up to plinth level in
Horizontal / Vertical/ Slanting surfaces.

1143.00 A) Foundations, Footings, Bases of columns, Mass SQM

concreting, Flooring, Pedestal, Plinth Beam etc.

A10 Providing rigid and water tight centering and shuttering

using best quality wood/ plywood/ steel forms and
centering with steel props, acro tubes etc.The centering
(vertical props, bracings etc.) shall be of steel tubes with
or without extension pieces or built-up section of rolled
steel, including strutting, propping, bracing, staging etc.,
complete for all RCC items fixed in position as required
including labour for careful removal of form work etc.,
complete all as per specifications up to the levels
indicated below in Horizontal / Vertical/ Slanting surfaces.

A) Columns, Pillars, Abutments, posts and struts.

85.00 i) Upto 3.50m level from FFL SQM

60.00 ii) Above 3.50m level to 6.00m level from FFL SQM

694.00 B) Walls (any thickness) including attached pilasters, SQM

buttresses plinth and string courses etc.

231.00 C) Staircase (except spiral staircase) excluding landings. SQM

Page 3
Item No Quantity Description of Item Unit Rate Rate in words Amount in (Rs.)
A11 Supplying and laying steel reinforcement for all R.C.C
items including decoiling, cutting, hooking, bending,
cranking, fabricating to required shape, placing in position
and tying the system with soft drawn annealed binding
wire of diameter not less than 1.00mm with 2 strands etc;
complete all as per specifications at all heights. (Binding
wire will not be measured for payment).

19.00 i) With themo mechanically treated (TMT) bars - Fe 500 D M.T

A12 Supplying, fabricating, assembling, hoisting/erecting and .

fixing in position up to the levels mentioned below and
with all leads, structural steel works of welded built-up
sections, all as per structural drawings and as per
detailed specifications (for materials and workmanship) in
the situations described hereinafter including a) cutting of
components to required lengths/widths and
shapes/profiles, smooth machining of edges/faces, c)
welding (electric arc welding) at joints of built-up
sections/single sections for required weld lengths and
sizes and d) coating all over with two coats of anti-
corrosive high performance Hi-build EPOXY coating of
approved colours (M/s Nagav Industrial Coats or
equivalent) over two coats of Epoxy zinc chromate grey
primer after applying a coat of rust converter chemical
even after thorough cleaning of the surfaces duly
prepared to receive painting etc., complete all as directed
by the Engineer-in-charge. NOTE : 1. The Contractor
shall submit fabrication shop drawings for work involved
based on construction drawings (that may be issued
during construction period) for approval by Engineer-in-
charge. 2. The quoted rate shall include making good of
the damages occured during erection.

issued during construction period) for approval by

Engineer-in-charge. The fabrication work shall start only
after approval to the fabrication drawings. Any change
required in the fabrication drawings shall be carried out at
no extra cost over the quoted rates. Fabrication shall be
in a perfectly workmanship like manner and as provided
in Section V and VI of IS 800 and IS 7215. Welding shall
be carried out by qualified welders. Electrodes for
welding, the procedure, selection, test and inspection
shall conform to provisions in IS 816, IS 818, IS 822, and
IS 833. Erection/hoisting shall commence only after
passing of fabricated parts by the Engineer -in- charge.

I) Above 6.00m level to 10.00m level from FFL

14.30 i) Structural steel works and welded built up sections in M.T

items above but with square/ rectangular tubular sections
of any size and any thickness.

0.70 ii) Structural steel works and welded built up sections in M.T
items above but with MS Plates of any thickness.

130.00 iii) Structural steel work of factory made MS Holding down KG

foundation bolts including nuts and washer plates of any
dia including necessary threading and machining

0.05 iv) Structural steel works as in item above but with MS M.T
angles, tees and other sections.

Page 4
Item No Quantity Description of Item Unit Rate Rate in words Amount in (Rs.)
A13 800.00 Supplying, fabrication and fixing of hand rails for staircase KG
using 30mmx30mm stainless steel hollow square section
(Stainless steel having Grade AISI 304) for vertical
ballustrades, fixing at 300mm c/c with hieght 900mm
above finished level of the platform 50mm outer dia of
stainless steel hollow tube for top handrails fixed over
20mm dia stainless steel hollow tube including providing
3 nos 20mm dia SS hollow tube parellel to hand rail
including fixing 40mmx 6mm stainless steel plate 100mm
long at the side of step by using necessary fixtures for
fixing the ballustrades, including cutting the section to the
required length line, welding, grinding etc.. as per
specifications, drawing and directions of Engineer in
charge at all heights.

A14 Providing and laying cement concrete in pavements and

ramps in panels not exceeding 10sqm per panel and
plinth protection in panels not exceeding 3sqm per panel
using graded hard granite stone aggregate including
providing necessary formwork, making 10mm wide
grooves in panels for depth of 1/3 rd of thickness of
pavement or 40mm which ever is more and filling the
grooves with approved hot poured sealing compound
confirming to grade A or B of IS-1834, consolidation,
curing and treatment for the top with broom finish, etc;
complete all as per specifications, Mix ratio specified is
for (cement: Manufactured sand: graded stone
aggregate).

5.50 i) Using 20mm nominal size aggregate In CC 1:3:6 CUM

A15 550.00 Providing and laying cement concrete interlocking paver SQM
blocks flooring using approved shape, size and colours
with required combination of colours of blocks having
55mm thick load bearing strength not less than M-20
grade manufactured by M/s. Heeralal / M/s. Vissco or
equivalent, close jointed over bed of 75mm thick
Manufactured sand to a tight pattern, laid to proper line
and level including bedding down the completed surface
with a plate vibrator or by firmly topping level with mallet
and a large flat piece of timber, finishing by brushing
clean dry sand over the surface to fill all the joints
thoroughly including fixing the edge restraint laying blocks
etc., complete all as per manufacturers specifications and
directions of Engineer in charge. (Rate to include cost of
paver blocks, sand and labour etc.). The arrangement of
pattern of blocks shall be as per architectural drawings.

A16 Providing and laying Indian patent stone flooring with

cement concrete 1:2:4 (1cement: 2 Manufactured sand: 4
graded stone aggregate) using graded granite stone
aggregate obtained from approved quarry laid to level or
slope in bays not exceeding 3sqm per panel including
providing 3mm thick Aluminium dividing strips to the full
depth of the flooring and finished smooth, curing, etc;
complete all as per specifications.

1422.00 i) 25mm thick (Using 12.5mm Nominal size stone SQM

aggregate).

Page 5
Item No Quantity Description of Item Unit Rate Rate in words Amount in (Rs.)
A17 Supplying and fixing aluminum industrial troughed .
coloured roofing sheet as per the following specifications:
AA3105 alloy, H18 temper colour coated of Hindalco
Industries Ltd. or equivalent using tight frames securing
to purlins by welding or with self tapping fasteners and a
metal washer and PP cap assembly to ensure water tight
fastening points at crest. The entire operation shall be
done as per the manufacture's specifications and as
directed by Engineer-in-charge. The quoted rate shall
include the cost of materials and roofing sheet
overlapping (such as aluminium sheets, self-tapping
fasteners, washers, etc.) and necessary staging/platform
required for fixing the above and specialized labour for all
the activities etc., complete all as per specifications and
as directed by Engineer-in-charge.

783.00 I) Thickness - 0.91 mm SQM

A18 Supplying and fixing close fitting adjustable aluminum .

plain sheet ridges matching the roofing sheet as per the
following specifications: AA3105 alloy, H18 temper colour
coated of Hindalco Industries Ltd. or equivalent. Rate to
include the cost of all materials and labours etc complete
at all heights all as per the direction of Engineer-in-
charge.

110.00 I) Thickness - 0.91 mm MTR

A19 Plastering 12mm thick with cement mortar using river

sand/M-sand specified below, finished rough including
mixing of admixtures of Ceraplast LMP at 200ml/50kg or
equivalent, scaffolding, curing, etc; complete for
EXTERNAL SURFACES inclusive of sills, jambs, soffits,
ceilings, etc; complete all as per specifications at all
heights/levels above GL. Mix specified is for cement :
coarse sand. NOTE : i) CM 1:3 OR CM 1:4 is generally
applicable for ceilings and RCC surfaces unless
otherwise specified.

565.00 A) With C.M. 1:4. SQM

A20 565.00 Painting external plastered surfaces with two or more SQM
coats of 100% acrylic exterior emulsion paint of approved
make and colour (ULTIMA PROTEK (Top coat) of Asian
paints or equivalent) over a coat of suitable water
proofing primer and base coat specified by manufacturer
having protection against fungal growth, flaking, fading,
alkali and UV degradation and to give an even shade with
required finish including cleaning the surfaces, filling the
crevices with approved filler, scaffolding, curing, etc.,
complete all as per specifications.

PART A TOTAL

Page 6
Item No Quantity Description of Item Unit Rate Rate in words Amount in (Rs.)
PART B : FENCING WORKS
B01 35.00 Earthwork in excavation for FOUNDATION TRENCHES in CUM
ALL KINDS OF SOILS including dressing of sides,
ramming of bottom, disposing the surplus excavated
materials within a distance of 50m and lift 1.50m complete
as per specifications. (Disposed soil to be levelled by
breaking clods if any and neatly dressed).

B02 13.00 Filling available excavated approved earth (excluding CUM

rock) in trenches, sides of foundations, plinth, etc; in
layers not exceeding 15cms depth breaking clods,
consolidating each deposited layer by ramming, watering
and dressing, etc; complete for lead up to 50m and all lifts
etc., complete as per specifications.

B03 Providing and laying cement concrete using 20mm

nominal size graded hard granite stone aggregate
obtained from approved quarry including compaction,
finishing top surface to level, curing but excluding cost of
formwork, etc; complete all as per specifications. Mix ratio
specified is for (cement:Graded Manufactured
Sand:graded stone aggregate).

7.00 I) In foundation and plinth/sub-base to floors with P.C.C. CUM

1:3:6

B04 Providing and Constructing Solid Cement Concrete block

masonry in Cement Mortar 1:6 (1 cement : 6
Manufactured Sand) using factory made, load bearing,
approved quality Cement Concrete blocks of specified
size, Grade A as per IS:2185 (Part II)-2005, Density of
blocks not less than 1500 kg/cum. Minimum average
Compressive strength of units - 4.0 N/sqmm and
Minimum strength of individual units 3.2 N/sqmm, setting
in position, curing, raking out joints wherever required
etc., complete with all leads and all as per specifications
and directions of the Engineer-in-charge. IN
FOUNDATION AND PLINTH.

17.00 I) For 200mm thick walls using (400x200x200)mm size CUM

blocks.

B05 Providing and laying cement concrete using graded hard

granite stone aggregate of 20mm nominal size obtained
from approved quarry including formwork, compaction,
finishing, curing, etc; IN BED BLOCKS, ANCHOR
BLOCKS, WINDOW CILLS, COPING BLOCKS, etc; up to
floor-V level complete all as per specifications. Mix ratio
specified is for (cement:Graded Manufactured
Sand:graded stone aggregate) The work includes
providing throating/ drip mould whereever required as per
standard engineering practice of size not be less than
40mm X 15mm. The rate is inclusive for making drip
mould & no extra cost will be paid for.

8.00 I) P.C.C 1:2:4 CUM

Page 7
Item No Quantity Description of Item Unit Rate Rate in words Amount in (Rs.)
B06 Providing rigid and water tight centering and shuttering
using best quality wood/ plywood/ steel forms and
centering with steel props, acro tubes etc. The centering
(vertical props, bracings etc.) shall be of steel tubes with
or without extension pieces or built-up section of rolled
steel, including strutting, propping, bracing, staging etc.,
complete for all RCC items fixed in position as required
including labour for careful removal of form work etc.,
complete all as per specifications up to plinth level in
Horizontal / Vertical/ Slanting surfaces.

20.00 A) Foundations, Footings, Bases of columns, Mass SQM

concreting, Floorings etc.

B07 Plastering 12mm thick with cement mortar using river

sand/M-sand specified below, finished rough including
scaffolding, curing, etc; complete for EXTERNAL
SURFACES inclusive of sills, jambs, soffits, ceilings, etc;
complete all as per specifications for heights upto 3.5
MTR above GL. Mix specified is for cement : coarse sand.
NOTE : i) CM 1:3 OR CM 1:4 is generally applicable for
ceilings and RCC surfaces unless otherwise specified.

80.00 I) With C.M. 1:5. SQM

B08 100.00 Supplying and fixing Stainless steel chain link fencing to SQM
FRP poles using SS 304 chain link fencing tied to the
post with 25x2.5mm SS flats using necessary SS screws
etc. including providing 10g SS wire horizontally at top
and bottom, cost of all materials required for the work,
etc; all as directed by the Engineer-in-charge using SS
chain link fencing of size 3" x3"x 12g. Note: The rate is
excluding the cost of SS flats which will be measured
elsewhere as a separate item.

B09 50.00 Supplying, fabricating and erecting in position FRP poles MTR
of potruded profile square pipe 50x50x5mm of M/s.
Everlast or equivalent including cutting, hoisting, fixing in
position all as per approved drawings and specifications
at all heights.

B10 Supplying, fabricating and erecting in position Stainless

steel works (SS 304) in single sections including cutting,
hoisting, fixing in position using screws etc. complete all
as per drawings and specifications at all heights.

30.00 I) In flats of all thickness. KG

PART B TOTAL

Page 8
Name of work: Construction of Rocket Launch Viewing Shelter near Space Museum at TERLS, VSSC, Thumba (Civil works)

SUMMARY OF COST

PART A : SHELTER WORKS

PART B : FENCING WORKS

TOTAL Rs.
Rebate Percentage
Rebate Amount Rs.
NET TOTAL Rs.
GRAND TOTAL Rs.