WWW.WHYDOITRAIN.

COM

Interview Questions

Planning Engineer
 WWW.WHYDOITRAIN.COM
Question-1:

What is a Base Project Schedule?

 WWW.WHYDOITRAIN.COM
Answer:

A baseline is an approved program by

both parties which is used as a bench
mark to measure progress of a project.
 WWW.WHYDOITRAIN.COM
Question-2:

What is a Main Driver of a Project and

how you will get it?
 WWW.WHYDOITRAIN.COM
Answer:

A main driver consist of the major activities

that are driving the project at critical path.
To get it just go to last activity and check its
driving activity, then go to that driving
activity and mark its driving also, same goes
until you reach the first activity. This is
normally done through scheduling software
like Primavera P6, Microsoft Project etc.
 WWW.WHYDOITRAIN.COM
Question-3:

How many baselines are allowed in any

project and which baseline decides the
success or failure of the project?
 WWW.WHYDOITRAIN.COM
Answer:

A project must have minimum one

project baseline & that number can go to
unlimited. But if you find more number
of baselines that means the planning
team is quite inefficient – Avoid it! The
latest baseline defines the success or
failure of any project.
 WWW.WHYDOITRAIN.COM
Question-4:

What are the Key Performance

Indicators – KPI’s?
 WWW.WHYDOITRAIN.COM
Answer: A KPI is type performance measurement on a
particular activity where engaged. KPI’s are
defined by keeping a factor “What matter the
most”. A careful study and analysis is required to
define because it differs from organization to
organization like a critical KPI for you may not
be of nay interest of other same type
organization. It is really a diverse area. Examples
Rubber lining, Concrete Work, Machine Failures
in a Specific Duration, Plantation, Number of
hiring/firings, Training etc. etc.
 WWW.WHYDOITRAIN.COM
Question-5:

What you normally need to develop a

plan?
 WWW.WHYDOITRAIN.COM
Answer:

I need the Contract documents to understand

the scope, the schedule drawings to know
about areas, Bill of Quantity-BOQ including
cost, scheduling software access. Yes, I need to
meet my project team to know about a little
productivity rates if I don’t know in case of any
specific activity.
 WWW.WHYDOITRAIN.COM
Question-6:

How do you define a critical path?

 WWW.WHYDOITRAIN.COM
Answer:

The longest path & the minimum time

required to complete a project. A
combination of activities with total float
as zero are included all.
 WWW.WHYDOITRAIN.COM
Question-7:

How much duration a milestone

activity normally has?
 WWW.WHYDOITRAIN.COM
Answer:

Well, there are different types of

milestones are there like start milestone,
finish milestone etc. but all have ZERO
duration.
 WWW.WHYDOITRAIN.COM
Question-8:

What is the difference between Free Float

& Total Float?
 WWW.WHYDOITRAIN.COM
Answer:

Free Float - amount of time we can delay an

activity without effecting the early start date
of its successor activity. Total Float - amount
of time we can delay an activity from its
early start date without delaying the whole
project finish.
Free float may affect the start of any activity
but total float may affect the duration of
overall project.
 WWW.WHYDOITRAIN.COM
Question-9:

What is the difference between Change

order & Variation order Request?
 WWW.WHYDOITRAIN.COM
Answer:

Technically there is no such a difference.

Change order or Variation request is a change
in scope from contract but as per contract. If
you are much curious which term should be
used the better refer your contract documents.
Personally, I have heard the term Variation
Order but never seen any documentation for.
Everywhere they write a Change Order
Request.
 WWW.WHYDOITRAIN.COM
Question-10:

How to measure progress of a

project?
 WWW.WHYDOITRAIN.COM
Answer:

Normally there are three ways to measure the progress

1)-Man-hours, 2)-Cost & 3)-Quantity
My preferred method is through Man-hours as It is
more logical but I have to comply as per contractual
obligations as most of the companies prefer through
Cost.
By the way, sometimes we have to use all three methods
on a single project to get more intensive project
updated status.
 WWW.WHYDOITRAIN.COM
Question-11:

Have you heard about Kick of Meeting?

 WWW.WHYDOITRAIN.COM
Answer:

Yes, I have handled a number of Kick of Meetings on

different projects & companies. kick-off meeting is
normally the first meeting of all major Stakeholders
including the Project Manger with his team and Owner’s
representatives. Here, we discuss high level overall plans,
things like how we are going to execute and once things get
clearer as project go forward then we do rolling wave
planning.
These meetings can be conducted at new phase start during
the execution of project also.
 WWW.WHYDOITRAIN.COM
Question-12:

What certification & qualification you

have?
 WWW.WHYDOITRAIN.COM
Answer:

I am a Project Management Professional-

PMP certified from Project Management
Institute – PMI. I am a Graduate
Engineer & perusing Master in Project
Management.
 WWW.WHYDOITRAIN.COM
Question-13:

Do you know about CPI?

 WWW.WHYDOITRAIN.COM
Answer:

Yes, it’s a Cost Performance Indicator and it

evaluates the performance in the sense if the
project is under-budget, over-budgeted or
on track. The formula is for CPI is the ratio
of earned value - EV over actual costs – AC
that is CPI =EV/AC
 WWW.WHYDOITRAIN.COM
Question-14:

What do you know about SPI?

 WWW.WHYDOITRAIN.COM
Answer:

It is Schedule Performance Indicator and

indicates the performance of project
work is completed to baseline schedule. It
is calculated by dividing the earned value
by the planned value that is SPI = EV/PV
 WWW.WHYDOITRAIN.COM
Question-15:

What you know about Triple Constraints?

 WWW.WHYDOITRAIN.COM
Answer:

Cost, Time and Scope with quality as the

fundamental theme.
 WWW.WHYDOITRAIN.COM
Question-16:

What are undesirable in any plan?

 WWW.WHYDOITRAIN.COM
Answer:

Constraints, SF (Start to Finish)

relationship, Log lags or leads, Negative
Float etc.
 WWW.WHYDOITRAIN.COM
Question-17:

How to avoid Negative Float in a Baseline

Schedule?
 WWW.WHYDOITRAIN.COM
Answer:

Negative float indicates that the activity is

already delayed. Normally, a constraints is the
culprit of it. Remove all the constraints or use
proper logic -relationships to deal with
it. Also check dangling or out of
sequence activities.
During updating a schedule, a negative float
for some activities is very common. You
cannot avoid unless is going as planned.
 WWW.WHYDOITRAIN.COM
Question-18:

If you are reported 5 SPI, what is means? –

Real Question was Asked to me!
 WWW.WHYDOITRAIN.COM
Answer:

They planner has made a blunder during

calculations.
 WWW.WHYDOITRAIN.COM
Question-19:

What is an S Curve?
 WWW.WHYDOITRAIN.COM
Answer:

Graphical representation of ‘anything’

like Manhours, Cost etc. plotted against
time.
 WWW.WHYDOITRAIN.COM
Question-20:

What do you know about Reflection

Schedule?
 WWW.WHYDOITRAIN.COM
Answer:

Reflection function is always

underestimated but it is really great
feature in Primavera P6 Professional. A
Reflection program is just a copy of the
program to have a look at different
scenarios after making desirable changes.
Once satisfied just merge in the native
program.
 WWW.WHYDOITRAIN.COM

For More questions , please visit
https://whydoitrain.com/