Q.

I PUBLICATI □ N 20698

using and
understanding
 Using and
Understanding
MINIATURE
NEON LAMPS

By
William G. Miller

Q I HOWARD W. SAMS & CO., INC.

I THE BDBBS-MERRILL CD., INC.
INOIANAPOLlS • KANSAS CITY * NEW YORK
 FIRST EDITION

FIRST PRINTING —1969

Copyright © 1969 by Howard W. Sams & Co., Inc.,

Indianapolis, Indiana 46206. Printed in the United States
of America.

All rights reserved. Reproduction or use, without express

permission, of editorial or pictorial content, in any manner,
is prohihited. No patent liability is assumed with respect
to the use of the information contained herein.

Library of Congress Catalog Card Number: 69-16778

 Contents

CHAPTER 1

The Neon Lamp. 7

Basic Operation — Corotrons — Progressive Explanation
of Terms — Physical Considerations

CHAPTER 2

Indicators.15
Incandescent Versus Neon — Standard Brightness — High
Brightness — Ultraviolet — Construction — Practical
Indicators

CHAPTER 3

Voltage Regulators and References.25

Description — Application — Regular Construction —
Circuit Design Considerations — Practical Regulator and
Reference Circuits

CHAPTER 4

Oscillators, Pulse Generators, and Flashers ... 37

Single-Lamp Oscillators — Two-Lamp Multivibrators —
Flashers
 CHAPTER 5

Computer Circuits.49
Bistable Multivibrator — Monostable Multivibrator —
Three-Input OR Gate — Three-Input AND Gate — Three-
Input MAJORITY Gate — Design Considerations — Ring
Counter — Trigger Circuits — Complete Decade Ring

CHAPTER 6

Miscellaneous Circuits.61
SCR Control — Relay Circuits — Photocell Circuits —
Photoconductive Junction Devices — Temperature and
Humidity Sensors — Timer Circuits — Touch Control —
Audio Switch — Variable Delay Circuit — Overvoltage
Circuits

CHAPTER 7

Power Supplies and Instruments.79

Unregulated 160-Volt Supplies — Regulated Power Sup¬
plies — Voltage Calibrators — Transient Voltmeter —
Electrician’s Friend — High-Energy Detector — A-M Sig¬
nal Generator

CHAPTER 8

Reference Section.93
Light Output — Shunt Capacitance and Internal Resist¬
ance — Dri-Film Coating and Leakage — Aging Proce¬
dures — Aging Equipment —- Neon-Lamp Specification
Chart and Numbering Systems — Using the Specification
Chart — Testing Guidelines —• Specifying Guidelines —
Pricing Guidelines — Mounting Considerations — Tl and
Ball-End Lamps — Tl% Crater-Electrode Lamps

Appendix. 117
Using the Nomograms.

Index 123
 Preface

Miniature glow lamps have been in use for many years and
are familiar to most readers as indicators and relaxation oscil¬
lators. Practically everyone has seen the inexpensive neon
tester, consisting of a neon glow lamp in series with a current-
limiting resistor, housed in a neat plastic enclosure terminated
with flexible test leads. This forms a convenient and reliable
means of testing for the presence of ac or dc voltages.
In electronics, the “state of the art” has progressed rapidly,
finding new applications for the glow lamp as a circuit ele¬
ment. Much of this progress results from the increasing use of
solid-state devices, many of them, like the transistor, requiring
comparatively low currents and voltages for operation.
Some of the characteristics that make the miniature neon
lamp particularly appealing to the hobbyist-experimenter are
its low cost, long life, dependability, and the ease with which it
can be made to work in extremely simple circuits. At the same
time, but probably unknown to the majority of persons who
work with electronics, the neon lamp can be used in some cir¬
cuits and applications that are quite sophisticated, complex, or
exacting.
This book is offered to present the student, hobbyist, techni¬
cian, and engineer with a more complete account of the prop¬
erties of neon lamps and to acquaint them with some of the
many ways in which neon lamps can be utilized.

William G. Miller
 The Neon Lamp

The neon lamp is basically a glass envelope filled with gas

and containing two or more electrodes. It is also referred to as
a gas tube, gas diode, glow tube, and glow lamp.
It might be interesting to note that the neon lamp does not
always contain neon alone, but may contain a mixture of
gases. Some gas lamps have no neon at all, but are included in
this discussion because the design considerations for all types
are similar. Long term reliability, low cost, and small power
and space requirements help account for its increased popu¬
larity.

BASIC OPERATION

The miniature neon lamp is a cold-cathode device and re¬

quires no heater. The electrodes are separated by an average
distance of Va inch inside the gas-filled envelope.
Under initial conditions, the gas acts as an insulator with
a resistance of about 1000 megohms. If a variable voltage is
applied across the electrodes (Fig. 1) and increased to ap¬
proximately 50 volts, there will be essentially no current fiowT,
due to the high insulation resistance of the gas.
Actually the gas atoms are constantly being bombarded and
ionized by external forces such as light. The positive ions thus
generated are attracted to the cathode, which has a negative
charge. The electrons that are liberated in the generation of
positive ions are accelerated to the positive anode, striking

7
other atoms as they travel, but they rarely attain enough ve¬
locity to dislodge more electrons and create new ions.
This velocity can be attained if an external voltage of suffi¬
cient amplitude is applied. When an electron dislodges addi¬
tional electrons, which in turn create even more ions, the
process is referred to as “run-away” or “avalanche,” and con¬
stitutes current flow. Run-away can be self destructive if un¬
controlled, so a series current-limiting resistor (Rs), must be
included. The exact value of voltage needed to start the ioniz¬
ing action is called the breakdown voltage.

Fig. 1-1. Voltage and current in a neon-

lamp circuit.

When breakdown voltage is applied to the circuit in Fig. 1-1

there will be a sharp deflection of the ammeter, and the volt¬
meter reading will drop to a value known as the maintaining
voltage of the lamp. The maintaining voltage of a lamp re¬
mains relatively constant over a wide current range.
The actual values of breakdown and maintaining voltage
will vary from one gas tube to another. They depend on many
factors, such as physical design, external radiation, and circuit
design.
The curve in Fig. 1-2 illustrates the characteristics of a
typical gas discharge device (glow lamp). It can be seen that
dynamic current does not begin to flow until the voltage
reaches point A. Breakdown occurs at point B, or 110 volts,
and the maintaining voltage is approximately 85 volts (point
D). When breakdown occurs, the current flow is said to be
self-sustaining. This means that the applied voltage can be
lowered to some value above the maintaining voltage and cur¬
rent flow will still continue to increase until the normal glow

8
region is reached. Note that the current scale is not linear,
but compressed for convenience.

COROTRONS

Corotron is the name given by the manufacturer to a line of

gas-filled diodes that are used to regulate voltages between
350 and 30,000 volts. Unlike the conventional regulator, they
do not glow, but operate on the slightly positive slope prior
to breakdown.
This is called the "corona mode” of operation and closely
resembles the action of a zener diode.
Corotrons are free of voltage jumps, oscillations, and photo¬
sensitivity. Current capability is, however, quite small. The
maximum figure for T2 types is 100 fxA and 3 mA is the limit
for even the largest type. Care must be taken never to exceed
the peak current rating or breakdown will occur and perma¬
nent component damage may result.

PROGRESSIVE EXPLANATION OF TERMS

Ion—An atom with an excess or deficiency of electrons.

Ionization—In glow lamps, the process of separating an
electron from an atom, creating a positive charge and a free
electron.

9
 This may be caused by collisions between atomic particles,
the application of a voltage, an electrostatic field, X rays, ultra¬
violet rays, cosmic rays, and radioactivity.
Corona—The visible glow of an ionized gas surrounding the
cathode.
Breakdown Voltage—Also called ionization voltage, strik¬
ing voltage, and firing potential. It is the voltage needed to
make a lamp glow. This is determined mainly by the type of
gas, electrode spacing, pressure, and external ionizing forces,
such as light.
Static Breakdown Voltage—The breakdown voltage under
controlled conditions, which include: freedom from electro¬
static fields, 5 to 50 foot candles of ambient light, and a 24-
hour period in a non-conducting state.
Townsend Discharge—An avalanche type of electron flow
that occurs just before breakdown voltage is reached. It is not
a self-sustained current flow.
Maintaining Voltage—Also called holding voltage. It is the
voltage across the lamp after breakdown. This voltage is at its
minimum in the normal glow region (Fig. 1-2, point D to E).
Normal Glow—The mode of operation that allows maximum
current variation with minimum change in voltage.
Abnormal Glow—A region of operation that is arrived at
by increasing the lamp current beyond the normal glow re¬
gion (Point E, Fig. 1-2).
Extinguishing Voltage—The voltage at which a lamp will
cease to glow.
Differential Voltage—The difference between the breakdown
voltage and maintaining voltage.
Ionization Time—The time required for a lamp to enter nor¬
mal glow after application of a voltage that is in excess of the
breakdown voltage.
This time may be well under 50 fj.sec if the applied voltage is
30 percent greater than the breakdown voltage.
Deionization Time—Definition 1: The time it take a lamp
to return to its static breakdown voltage after current ceases
to flow.
Definition 2: In a dc circuit, if a lamp is extinguished by a
rectangular pulse, it is the time which must elapse before 90
percent of the original breakdown voltage can be reapplied and
still not cause breakdown.

10
 The first definition is used for most circuit applications, but
if higher frequency oscillators and counters are being consid¬
ered, the latter definition would be more useful.
Deionization time is affected by tube construction, the mag¬
nitude of the conduction current, and most of all by the ampli¬
tude of the extinguishing voltage.
Dark Effect—The effect that light has on breakdown volt¬
age. Higher ambient light levels produce lower breakdown volt¬
ages. If a lamp is to be operated in total darkness, it is usually
necessary to simulate ambient light by the addition of a small
amount of radioactivity.
Standing Rise—The rise in breakdown voltage that some
lamps incur after extended periods of storage. This is mainly
caused by the glass and other internal solids releasing gas
molecules.
Negative Resistance—An increase in current caused by a
decrease in voltage. This can be noted on the characteristic
curve of most lamps. In Fig. 1-2 this corresponds to that part
of the curve between points C and D.
Design Current—The value of operating current upon which
the end-of-life figures are based.
Transmission Time—The time required for an input level
change to appear on the output of a lamp already in the con¬
ducting state. This is usually less than 8 ^sec and is a func¬
tion of the conducting current.
End-of-Life—A glow lamp that is used for its light output
is said to have reached its end-of-life when the light output
falls to 50 percent of its original value. If a lamp is used as a
circuit component, the end-of-life occurs when the character¬
istics fall out of specifications. Lamps operated on ac have
longer life figures due to shorter duty cycle.
Aging—The process of operating a new lamp at an increased
current level for periods in excess of 24 hours in order to stabi¬
lize its characteristics.
The aging process varies for different lamps and is usually
done in the factory. However, aging is not required for all
lamp applications.
Sputtering—A phenomena that occurs when lamps are op¬
erated at higher currents. Certain quantities of the metal cath¬
ode material will vaporize, and when the vapor comes in con¬
tact with the cooler glass envelope, it solidifies. This thin film

11
of sputtered metal is opaque and restricts light output, but it
also increases electrical stability.
Polarization—A lamp is said to be polarized when its char¬
acteristics change with a reversal of polarity. Lamps that are
aged or operated on dc exhibit this effect. Lamps that are aged
on dc are coded to designate the anode or positive terminal.
Work Function—A measure of the ability of a material to
give up electrons. Molybdenum is said to have a lower work
function than nickel because it releases more electrons for a
given voltage.

PHYSICAL CONSIDERATIONS
Gases
Gases—The inert or “rare” gases are used in the manufac¬
ture of glow lamps. Neon is the basic gas, but other gases may
be used in mixtures to achieve special results.
Neon—The basic glow-lamp gas, noted for its high light out¬
put, and low breakdown and maintaining voltage. The charac¬
teristic color of the neon glow is red-orange.
Helium—A low breakdown, low light-output gas that may
be mixed with neon to produce a specific value of breakdown
or maintaining voltage.
Argon—This gas has a higher breakdown voltage, but if as
little as 0.1 percent is added to neon, the breakdown voltage
for the mixture is lower than for either gas alone. Pure argon
is used as an ultraviolet light source.
Xenon—A high-breakdown gas that is used to produce a
brilliant white light and is also used as a noise source. This
gas has not found much application in miniature gas tubes.
Krypton—A gas with qualities similar to argon. It is added
to neon to raise the breakdown and maintaining voltages, and
is an excellent source of ultraviolet light.
Krypton 85—A radioactive isotope of krypton that is added
to neon or other gases to provide partial ionization and stabil¬
ity to compensate for the dark effect.

Electrodes
Material—Nickel and molybdenum are the two common elec¬
trode metals. Molybdenum tends to lower the breakdown and
maintaining voltage and can carry higher currents.

12
 Spacing—Increased spacing between the electrodes increases
breakdown voltage but has little efTect on the maintaining
voltage.
Coating—Emissive materials such as barium and strontium
are used to coat the electrodes and allow the cathode to give
up electrons more freely. This results in lower breakdown volt¬
ages and higher, more uniform light output. Gas tubes that
use emissive material will change their characteristics with
time. NE2 lamps are in this class.
Size—The size of an electrode will determine its light ra¬
diating area and current carrying ability.

Pressure
Increasing the internal gas pressure will raise the break¬
down voltage of the lamp without major changes in the main¬
taining voltage. Lamps with a high differential between break¬
down and maintaining voltage are useful as counters, high
power oscillators, and energy transfer diodes.
In general, high-pressure gas tubes will exhibit poor light
output and an unstable corona that results in voltage jumps
and noise.

Temperature
Gas tubes have a negative temperature coefficient. Most in¬
dicator types will drop 50 mV in maintaining voltage for each
Celsius (centigrade) degree of increase. Circuit component
types and regulators may have a figure as low as —2 mV per
degree C.

Radiation
The electrical characteristics, the electrodes, and the gas are
relatively unaffected by gamma radiation. The glass, however,
will darken and become brittle.
Rf radiation or a strong ac field will ionize the gas directly.

13
 2

Indicators

The miniature glow lamp has found widespread use as an

indicator in electronic, commercial, and industrial equipment.
A brief comparison to the incandescent type is offered to help
explain both their popularity and their limitations.

INCANDESCENT VERSUS NEON

A specific lamp must be indicated if the ratings are going to

be based on such items as temperature, vibration, shock, or
humidity. Both types have indicators that perform well in
these areas.
The tungsten filament is basically a low-voltage, high-cur¬
rent device, while the neon requires higher voltages and smal¬
ler currents. The efficiency figures of each vary widely, but in
comparing the NE2H with CM8-806, which is a Chicago Min¬
iature, 100,000 hour, tungsten-filament lamp, the efficiencies
were found to be equal at 2.2 lumens per watt. If life expec¬
tancy is plotted against cost, the neon lamp is unparalleled.
Even the most economical glow lamps have a life of 20,000
hours.
As a result of efforts to improve the tungsten life figures,
several lines of miniature incandescents have appeared on the
market with life expectancies of 20, 50, and 100 thousand
hours. These lamps are relatively expensive and the life fig¬
ures are based on “burnout.” Since neons do not burn out,

15
their life is calculated on other factors, such as tube darken¬
ing. (Envelope darkening can occur with both types.)
When a high-brightness neon is operated at half its design
current, it will give over a million hours of use before darken¬
ing restricts its light output by 50 percent.
Neon lamps perform poorly at altitudes higher than 70,000
feet, where the lower atmospheric pressures encourage ex¬
ternal corona and arcing.
The tungsten-filament lamp can produce high light intensi¬
ties over a wide range of light frequencies. Filters of paint,
plastic, etc., can be used to “color” the incandescent light, but
this cannot be done to any usable degree with neon. Colors
such as green, seen in outdoor neon signs, are the result of
phosphors or a combination of helium and mercury vapor used
with noviol or uranium glass. Helium and mercury vapor are
usually considered unsuitable for use in miniature lamps.
As a result of the preceding comparison, it would be reason¬
able to assume that cost and life expectancy are the main rea¬
sons for selecting a neon as an indicator. Actually, all but a
very few glow lamps can be called indicators because they emit
light. There are, however, three basic types that are designed
specifically for their light radiating ability.

STANDARD BRIGHTNESS

The NE2 is in this category and is the most popular of all

the lamps. It has the lowest current requirements and exhibits
a gradual change in characteristics with extended operation.
The light output falls off at a uniform rate, due to sputtering,
and the breakdown voltage rises slightly.
If you double the design current, you will double the light
output, but its life expectancy should be divided by 8. The in¬
verse holds true if design current is halved. Light output will
be halved, but life figures can be multiplied by 8.

HIGH BRIGHTNESS
The NE2H is a lamp of this type and differs from the stan¬
dard-brightness variety in several ways. It has a higher ini¬
tial breakdown voltage, and when it reaches its end of life, the

16
breakdown rises to a point that is higher than the peak line
voltage (160V), and the lamp will no longer ignite.
The high-brightness lamp has 10 times the light output of
a standard brightness unit and can carry more current. It
maintains a fairly steady characteristic until it reaches its
end of life. The maintaining voltage of this type of lamp is
unstable. “Voltage jumps” and high noise levels are not un¬
common, so this restricts its use as a circuit element.
As in the case of the standard-brightness lamp, if the design
current is doubled or halved, the light output will also be dou¬
bled or halved, but the life figures will have to be multiplied
or divided by 64 instead of 8.

ULTRAVIOLET

Gas tubes filled with argon fall into this category. They emit
a deep blue light, and are used primarily for their color. Very
little true ultraviolet radiation is able to penetrate the glass
envelope so they are relatively safe to work with. The AR9 is
an example of this type.

CONSTRUCTION

American and foreign companies have made efforts in re¬

cent years to change the physical design of the lamps, either
for esthetic and space requirements or to increase the light
output.
General Electric has a complete line of lamps that have
formed tips instead of the standard drawn tip. These lamps
not only look better but increase the light output when viewed
end-on.
Tech-Neon, Signalite and GE all offer acid-frost lamps,
which give a pleasing, uniform light output.
The British, French, Belgian, and Italian companies offer
some lamps that are exotic by American standards. Most of
these companies manufacture a line of lamps with a lens that
is an integral part of the envelope. They also produce lamps
with axial leads. One European manufacturer even produces
a lamp that glows green. This is done by coating the inside
with green phosphor and filling the envelope with argon. AH
of these lamps are expensive, and for that reason the Ameri-

17
can companies hesitate to produce them. There is also a ma¬
jor glow-lamp manufacturer in Canada that offers essentially
the same products as the American companies.
The recent trend by many equipment manufacturers has
been to use lamps that have been encapsulated in plastic along
with the ballast or series resistor. This improves the appear¬
ance and greatly simplifies mounting. Many domestic and for¬
eign companies, including Japanese, offer this type of indi¬
cator.

PRACTICAL INDICATORS

Some lamps come with a series or current-limiting resistor

attached, but, if not, its value may be calculated. The glow
lamp specification sheet will recommend a particular value
for standard line voltages, but the designer may have a wide
range of voltages to contend with.
Example: It is necessary to have a visual indication that
power has been supplied to the circuit in Fig. 2-1. For illustra-

Fig. 2-1. Neon indicators in a power supply.

tion, we chose point A and B as possible locations. The formula

for both resistors is the same, but they are handled differently.
The formula is:

_ Egpp Ematnt

Idwlp

In other words the resistor has to drop the difference between

the applied voltage and the maintaining voltage of the lamp
at the design current.

18
 Solution for II:
__ 300 -39
“ .0005
Rs= 510k
Solution for 12:
_ 410 - 55
Kss “ .0005
Rss = 680k
Resistors are to the
closest 10% El A value.

Since II is in an ac circuit, rms values were used. Location B

will provide a positive indication of B-(- but only one electrode
will glow. The total measured light output from both lamps
is approximately equal.
The indicator in Fig. 2-2 will ionize only w'hen Eam> or sup¬
ply voltage has reached 150 Vdc. The value of Rs is solved in
the usual manner and forms part of a voltage divider with Rd.
Rd was selected to provide the maximum rated breakdown volt¬
age (90) at point A, when the supply reaches 150 volts. Greater
accuracy can be had if the exact value of breakdown is known.
II in Fig. 2-3 will give a visible indication of voltages
throughout the range shown. The circuit functions in the usual
manner down to about 500V at which point C, II, and R* will
switch to relaxation oscillations and the lamp will flash
brightly.

^app o
®
USOV DC MIN) 180K
l 1
Fig. 2-2. Voltage level indicator. Rd<
270K1 NE5i '
JF -J=

+90V

fig, 2-3. Wide-range indicator.

19
 *s
*50/0-WV-
27K

vl© I T2-27-IR100 Fig, 2-4. Nonlatching indicator.

The simple nonlatching circuit in Fig. 2-4 is useful when

operation is required from a low voltage source (24V), such
as a transistor collector. The value of the supply voltage is
less than the lamp’s lowest rated extinguishing voltage. A
negative 24-volt pulse is added algebraically to the supply
voltage to total 74 volts, which equals the highest rated break¬
down voltage for the lamp. The lamp can remain on only when
the negative pulse is present on the cathode.
Fig. 2-5 shows another nonlatching circuit that features use
of low voltage transistors (18V) and even lower control volt¬
ages (4-IV). Q1 is normally saturated so the 62V developed
by the zener diode is not enough to ionize the 5AGA. When Q1
is cut off by a +1V pulse or by grounding the base, the -18V

XI TO ADDITIONAL

3K
Fig. 2-5. Nonlatching indicators using low-voltage transistors.

20
will be felt at the cathode of the lamp through the 10k resistor.
This voltage which is added to the zener voltage should ex¬
ceed the lamp’s maximum rated firing voltage. The lamp is
extinguished 60 times a second by the ac input so there is no
need for a separate turn-off circuit.
The power supply voltages in Fig. 2-6 are selected to be
lower than the minimum rated breakdown voltage and higher
than the maximum rated maintaining voltage. The input pulse
is added to E.,H, to cause breakdown and the supply will sup¬
port ionization at the maintaining voltage. Fig. 2-6B illus¬
trates how the same principle may be used to extinguish
the lamp.

Availability of high-quality, low-leakage transistors at

prices considerably less than a dollar has made direct opera¬
tion of neon lamps economically practical.
The transistor selected for the type of circuit shown in Fig.
2-7 must be able to withstand voltages that are equal to Efl„p
minus the lowest rated maintaining voltage of the neon lamp.
The 1.2K resistor prevents false starting by minimizing leak¬
age effects.
In computer technology and other related fields, it is some¬
times necessary to have a visual indication of a very short
pulse. Since pulses shorter than 50 /as rarely can cause ioniza¬
tion, special circuits are required. The circuit in Fig. 2-8 will
respond to pulses shorter than 1 /as and cause the neon lamp
to glow. The incoming pulse charges C through the dynamic

21
 Rs

GE5AB-B

MOTOROLA
MPS 2924

impedance (50fl) of the 1N38. This switches the 2N337 on

and fires the neon lamp. Since C cannot discharge through
the diode, the transistor will remain on until C discharges
through Rk and Ql. Increasing the value of C will allow the
lamp to remain on longer but will decrease the input sensi¬
tivity.
Five different conditions may be represented by a single
lamp as shown in Fig. 2-9. In position 4, R„ is too large to
support ionization so RC oscillations will result from the
charging and discharging of the .01 ^F capacitor. Fig. 2-10A
shows a circuit that will indicate a blown line fuse and Fig.
2-10B will indicate a good fuse.

Rs

22
 RS
115VACO- -VvV-
22K
IN 1763

SI POSITIONS
1 - OFF
2 - RIGHT ELECTRODE 2.2meg
3 - LEFT ELECTRODE
4 - FLASHING
5 - BOTH C .OluF

Vl{
SIG LT2-32-1 HI

Fig. 2-9. Five-state indicator.

COMO O
(A) Blown-fuse indicator.
Fig. 2-10. Fuse indicators.

Fig. 2-11. Speaker operation indicator.

23
 TEFLON COVERED WIRE

In remote or multiple speaker installations, it is sometimes

desirable to have a visible indication of operation. A small
audio output transformer, with the low impedance side con¬
nected to the speaker terminals as in Fig. 2-11, will step up
the small audio voltage to a value that will operate the neon
lamp. The transformer is not critical, but the brightness of
the lamp will be affected by the Z or turns ratio, as well as the
amplifier output.

115VACO

Fig. 2-13. High-efficiency one-million

hour circuit.

The novel circuit in Fig. 2-12 utilizes the flame as a high Z

conductor to keep the neon lamp lit. When the pilot light goes
out, the random concentrations of cold gas will act as an open
circuit.
When extremely long life and low power dissipation are
required, the circuit in Fig. 2-13 might be considered. Instead
of resistance, X<. is used to limit the current to the desired
value. In this example the C2A (NE2H) is operated at half
its design current, so its life figures are increased by a factor
of 64.

24
 Voltage Regulators
and References

DESCRIPTION
Recent technology and manufacturing techniques have pro¬
duced a miniature voltage regulator that has the physical di¬
mensions of other neon lamps, but is capable of current
variation over ranges as wide as 15 mA. Its maintaining volt¬
age will change less than one volt, and life figures are in excess
of 20,000 hours. These gas diodes can replace the older 7- and
8-pin “tube” type regulators in all but a few7 applications. They
are ideally suited for printed circuit boards, encapsulation, and
other modern fabrication methods.

APPLICATION
In many cases, the same gas tube may be used both as a
regulator and as a reference. The GE 5AB lamp, for instance,
is used extensively as a voltage reference, but also provides
excellent regulation of vacuum-tube screen-grid voltages. This
lamp is simply an aged NE2 with a small amount of radio¬
activity added for the reduction of the “dark effect.” The
electrodes have an oxide coating and accordingly the lamp’s
characteristics will change slightly with use. This effect can
be disregarded in many applications such as the reference

25
voltage in series-regulated vacuum-tube power supplies, where
gradual change over a period of months can be tolerated.
On the other hand, applications such as voltage calibrators
and unmanned communication sites may require not only good
regulation, but a specific voltage value over extended periods
of time.

REGULATOR CONSTRUCTION

The high-current regulators achieve their characteristics

by several means. The electrodes are made longer and larger
in diameter to increase the current carrying ability. European
manufacturers use an anode that is somewhat smaller than the
cathode. American firms favor identical electrodes and there
appears to be some controversy as to which one produces the
best results.
Both designs utilize electrodes that can carry current loads
in excess of 60 mA. The limiting factors are the bulb tempera¬
ture and the point at which the tube will arc.
The electrodes of a high-current regulator are pure metal
and contain no oxide coatings. This is a necessary condition
for a wide current range and long-term stability. They also
are aged at higher currents for longer periods than the refer¬
ence type diode.
Extended aging is needed to sputter or vaporize the cathode
surface metal that may have trapped gas atoms during manu¬
facture. This process, sometimes referred to as “cleaning up,”
is essential for reliable operation. These gas tubes can be
recognized by their characteristic black or silver appearance,
which is caused by the deposit of sputtered cathode material
on the wall of the lamp.

CIRCUIT DESIGN CONSIDERATIONS

Since it is not the purpose of this book to present an exact¬

ing mathematical analysis of neon-lamp circuits, certain as¬
sumptions have been made that are not necessarily so.
The formulas, for instance, have omitted resistor tolerances,
temperature coefficients, and the dynamic impedance of the
conducting gas tube. All formulas have been reduced to the
simplest possible form and, in some cases, expressed literally

26
rather than mathematically. Selection of resistors was done
by choosing the standard EIA value that was closest to the
calculated value.

practical regulator and

REFERENCE CIRCUITS

The circuit in Fig. 3-1 is the basic and most widely used
method of obtaining a reference voltage. The supply voltage
(EU1)„), must exceed the rated breakdown voltage and is
applied to VI through the current-limiting resistor Rs. This
causes the lamp to ionize and its characteristic maintaining
voltage (EnMiui) will appear at point A. Once the correct tube
has been selected, only the value of series resistance must be
calculated.

= Eum> ~ Fiv.nint

Idwign

The maintaining voltage and the design current can readily

be obtained from the specifications sheet.
The foregoing formula will hold true as long as Rx remains
relatively high. It can be seen that Rx forms a voltage divider
with Rs> and under initial conditions breakdown or “firing”
voltage must appear at point A or VI will not ionize. Once
the gas tube conducts, the value of Rx must remain high
enough to sustain ionization. Voltage-divider action is still
present at point A and if this voltage drops below the main¬
taining voltage the lamp will be extinguished. In other words,
if the circuit in Fig. 3-1 is used, the load current cannot exceed
the design current.
Fig. 3-2 illustrates a circuit that compensates for unusually
wide variations of input voltage. VI is rated to regulate over
a 15 mA range. R* was chosen to cause 1 mA to flow at +140 V.
The minimum load resistance is calculated by determining

Fig. 3-1. Basic voltage-roferanc® circuit.

27
 +14W +82V i IV
TO Rs
1.2%
+ 95 WO-VW
REGULATED Fig. 3*2. Voltage regulator For
IE ___) 58K
3PP input variations.
VI Hl-Z LOAD
NU162/82 (330KMIN)

what value R, in series with RK, is necessary to cause the

maximum rated E,lkllwn (118V) to appear at point A when the
minimum voltage ( + 140V) is applied.
It can be seen in Fig. 3-3 that the same gas tube can be used
to compensate for changing load conditions. If the NU 162/82
regulator is operated at its maximum rated current, a regu¬
lated 0-5.5 mA output is realized. Actually this circuit would
be capable of a regulated 15 mA output, except that under
initial conditions the value of R* would be so low as to prevent
breakdown voltage from appearing at point A.
The simple circuit in Fig. 3-4 compensates for both input
and output voltage variations. It represents a compromise of
the circuits shown in Figs. 3-2 and 3-3.

k 160V 0-WV
© * 82V i IV TO O-WV +82V +1V
5.2K 1.2% + 175V 6.2K 1.2%
REGULATED REGULATED
VI
0-5.5 mA 0-3.5mA
NU 162182

Fig. 3*3. Voltage regulator for Fig. 3-4. General-purpose

load variations. voltage regulator.

The voltage divider limitations of Figs. 3-2, 3-3, and 3-4

are overcome by the addition of a replacement-grade silicon
diode XI, and a “firing” resistor (Rf), as shown in Fig. 3-5.
Under initial conditions, the load may draw 15 mA and the
voltage at point A will never reach breakdown. This “low”
voltage is isolated from the gas tube by diode XI, so that VI
may be ionized by the current through Rf. After ionization
point A will be positive with respect to point B, so XI will
conduct and operation will be the same as in previous circuits.
The value of Rf is calculated in the same manner as Rs except
that the value of I is small. Current through Rf must be large

28
enough to sustain ionization, but can be considerably smaller
than the .5 mA arbitrarily chosen in Fig. 3-5.
A stable higher voltage reference is achieved in Fig. 3-6 by
operating two gas tubes in series. The reference voltage is the
sum of the two maintaining voltages and must exceed the
sum of the two breakdown voltages.
Fig. 3-7 illustrates a useful circuit that produces a high
reference voltage with relatively small supply voltage. In this
instance, the series breakdown voltages exceed E,,,,,,. Elljn, may
drop as low as 4- 130V and still deliver a precise 124-volt refer¬
ence. This is done by diode isolation and shunt starting as in
Fig. 3-5. Rf fires V2 and Rff fires VI. RK is calculated as in
previous circuits.
The 300-volt regulator shown in Fig. 3-8 can be contained in
a space the size of a 20-watt resistor and can deliver 3.6 watts
of power to the load. Since the total breakdown of the three
gas tubes in series equals 450 volts, Rf and Rff must be used to
initiate ionization. Rr fires V3 and Rff fires VI. V2 will then
ionize because of the potential difference between points B
and C.
Parallel starting can be used for any number of tubes. Fig.
3-9 shows two methods for an identical 4-tube supply. In
Fig. 3-9A, the use of a single resistor, Rf, enables the minimum
applied voltage to be reduced from 600V to 500V. Two addi¬
tional resistors, Rf and Rff in Fig. 3-9B, further reduce the
voltage requirements to 450V. Fig. 3-9B is usually the pre¬
ferred method, as the starting resistors are V4-watt 20-percent
components, and the main savings are realized in applied
power and the power dissipated by R„.

Fig. 3-5. Shunt starting regulator with Fig. 3-6. Series starting, series operation

diode isolation. voltage reference.

29
Fig. 3-7. Shunt starting, series operation Fig. 3-8. Shunt starting, series operation

voltage reference. high-voltage regulator.

Small capacitors may also be used in place of the firing

resistors. “Capacitive starting” is usually more expensive and
requires more space, but these circuits dissipate less heat and
require less current.
+520V O-1 M60VO—e-]
(500 MINI (450 MIN) I i
Rs | 10K 2W Rf <220K R$< 5K 1W

- +40CV +4V -► * 4 (W +4V

1% REGULATED 1% REGULATED
0-l0mA O-lOmA

ALL LAMPS
V2 Z100R12

V3

220K

V4

(A) Using one shunt resistor. (B) Using three shuni resistors.

Fig. 3-9. Shunt starling, series operation four-tube regulators.

30
 A cascaded reference is used when an extreme degree of
regulation is required. In Fig. 3-10 a change of 100V at the
source will produce a change of less than 1 part in 10,000 at
the output. The maintaining voltage (Emilll„) of VI must ex¬
ceed the Ebkdwn of V2. R* and RKH are found by the formulas:

_ E„im (min) — Eaiaint(Vl)

“ I(Vlmin) + I(V2)
_ Euiaint (VI) — Ellialll, (V2)
I (V2)
VI may be a more economical lamp and still provide a reliable
circuit.
♦55V
—► TO
+ 70V
Fig. 3-10. High-stability cascaded reference. .01% REGULATED
(HAND
SELECTED
VALUES)

The maintaining voltages of VI and V2 in Fig. 3-11 are

close enough to make parallel operation practical. Diodes XI
and X2 isolate the load from Rf and Rfr for initial ionization
and also serve to isolate VI from V2. The value of Rs is found
by treating VI and 2 as one gas diode with twice the current
rating. XI and X2 are replacement-grade silicon diodes.
The novel circuit shown in Fig. 3-12 may be used to estab¬
lish precise low-voltage references. The output voltage is the

Fig. 3-11. High-current parallel regulator.

31
difference between the maintaining voltages at points A and
B.
The high-current regulator in Fig. 3-13 appears to be a
conventional shunt starting circuit, but a closer look at the
values and performance figures will indicate a different mode
of operation.
Moat circuit designers will agree that the load current
should rarely exceed the rated tube current and this premise is
true if you do not place any limitation on the minimum amount
of current that may be drawn by the load. If the “zener diode”
approach is used, the load current may be many times the
tube’s maximum rated value.
This is possible if we consider that when a gas diode regu¬
lator is rated at 12 mA, that means it will stay within specifi¬
cation over this range. It does not mean that 12 mA will be
delivered to the load. Tube VI is still regulating 100V ± IV
over a 12-mA range, but at a 110-mA level. If the supply
voltage is held at a constant 160V, the load may vary between
100 to 120 mA and still be within 2 percent of 100V. The im-

Fig. 3-13. High-current, high-

voltage regulator.

32
portant limitation of this circuit is that there is a minimum
current the load must draw. Fuse FI is included to protect
VI, if the load is reduced or removed.
Design procedure for Fig. 3-13:

1. Select regulator tube after determining the maintaining

voltage required and range of regulation.
2. Let R,- be 120K unless the supply voltage is over 200
volts, then double or triple this value. (Not critical.)
3. Let XI be any 400-PIV, 200-mA diode or better.
4. Find I, = lx + I (VI)

Find R, = ^

Find Rx =

Solution:
Rs = R, — Rx
where,
E,,,,,, is the supply voltage,
I* is the minimum current required by load,
I (VI) is the maximum rated lamp current,
Rx is the load resistance,
R, is the total circuit resistance,
It is the total circuit current,
R* is the series limiting resistor,
Eu,nil„ is the maintaining voltage.

Fig. 3-14 is one variation of a popular circuit. The wide

variety of screen-grid voltages and currents makes a standard
circuit impractical. The voltage needed at point A is usually
high enough to require two or more lamps in series. Rs, VI,
and V2 comprise the regulator system, but any of the systems
previously discussed may be used. I,i,.„iKJI is the maximum
screen-grid current.
Algebraic addition can provide a regulated low-voltage,
wide-temperature-range suppty as shown in Fig. 3-15. The
negative 100 volts developed by VI is added to the positive
82 volts of V2 at point A and the result is a negative 18 volts.
VI is rated at 10 mA but K* had to be increased to 18K in
order to sustain ionization of V2. Cl is an example of capaci¬
tive starting and is included to ensure that point A will reach

33
 © Fig. 3-14. Vacuum-tube screen

grid regulator.

the breakdown voltage of V2. The filter capacitors may be

lower in value and if 220 Vac is used, Cl may be omitted, R.
and Rss may be calculated for full tube current, and regula¬
tion will occur over a 10 mA range.
The circuit in Fig. 3-15 has one advantage over other low-
voltage types in that it has a common ground. In all differ¬
ential or algebraic circuits, the tolerances will add, so the final
performance figures will be half that for a single tube.
VI in Fig. 3-16 is a voltage reference for V2. In this series-
pass voltage regulator, current carrying ability and regulation
are the prime considerations—an A057B would be a suitable

Fig. 3-J5. Algebraic low-voltage regulator.

34
Fig. 316. Series-pass regulated reference.

> OUTPUT
■S CONTROL
< 150K

choice. The maintaining voltage of VI will determine the low-

voltage limits of the regulator. V2 can be any miniature dual-
triode that meets voltage and current requirements.
High voltage and high current are both available from the
circuit illustrated in Fig. 3-17. This circuit can be constructed
for less than $2.00 at present list prices and is physically small.
If better regulation for input variations is required, the
T2-32-1 lamps should be pre-aged at 10 mA for 24 hours. The
sum of the two maintaining voltages minus the junction drop
(0.6V) will determine the exact output voltage.

35
 Enpp - Emat>tr (both tubes)
I load \
fi (transistor beta)/
Rf is the shunt-starting resistor and the value is not critical.
Shunt starting in this case is highly desirable as it reduces the
value of Enpi> that is needed. The closer the voltage at point A
is to Eapil, the less power Q1 will have to dissipate. It also allows
lower transistor voltage ratings. The capacitors are for junc¬
tion protection and are not critical.

36
 4

Oscillators,
Pulse Generators,
and Flashers

Simple gas-tube relaxation oscillators are capable of pro¬

ducing a wide variety of complex waveforms. Their main limi¬
tation is the useful upper frequency limit. Pulses with rise
times of less than 1 fis are not unusual, but repetition rates
or operating frequencies of more than 10 kHz are difficult to
achieve.

SINGLE-LAMP OSCILLATORS

Fig. 4-1 illustrates a simple form of relaxation oscillator.

When SI is closed, VI cannot fire until the voltage across C
reaches the breakdown voltage. C is charged through R„. and
this time constant is a major factor in determining the fre¬
quency. When C charges to the breakdown value, VI will ionize
and C will discharge through the gas tube to a value referred
to as the dynamic extinguishing voltage E«t. VI then turns off
and the cycle repeats. R* must be high enough in value to in¬
hibit ionization or VI will continue to stay “On” after C has
reached Eljkdwn.
Note that only on the first cycle does the sawtooth begin
from zero volts, and thereafter it varies from Ellkd,ril to ErSt.
Since T represents only a portion of the RC time constant

37
 (R« X C), the actual frequency of operation will be higher
than the calculated, (1/R* x C).
Power supply voltages are equally as important as Rs and
C in determining frequency. If the supply voltage Ea|)p is
raised, the breakdown voltage will be shifted to a steeper por¬
tion of the charging curve and VI will fire sooner, thereby
raising the frequency. This, of course, will also improve the
linearity of the sawtooth. If the supply voltage is too close to
Ebkdwjw erratic operation will result. Small tube variations can
produce large frequency changes when operation is on the
upper part of the RC curve.

Fig. 4-1. Relaxation oscillator.

The dynamic impedance of the neon tube, the differential

between Ebkdwn and E,.xt, as well as the value of C, will determine
Td or the capacitor discharge time. At lower frequencies this
value is negligible, but it is a major factor over 1 kHz. The
formula for the approximate frequency of oscillation is:

f =___i _
2.3 RClog%^—

Precise frequencies are best obtained by trial and error.

Sawtooth amplitude is basically a function of the neon tube
differential voltage or E«f, which is Ebkdwn “ E„t- This also
changes with frequency and the value of series resistance.
Large values of series resistance tend to lower the dynamic
extinguishing voltage.

38
 For a more thorough mathematical approach to neon-
lamp oscillators, the reader should refer to the GE glow-lamp
manual.
One of the main objections to gas-tube oscillators has been
the wide variation in tube parameters and changing electrical
characteristics. Tolerances as close as 1 percent for 20,000
hours are now available, and even tighter specifications may be
had, but the life expectancy figures on all these types are not
yet complete.
In the following discussion it can be noted that NE2 and
other indicator-type lamps are used frequently. This is done
because the circuit designer and experimenter usually have
these types available. Other lamps with closer specifications and
no emissive coating on the electrodes would certainly be a
better choice for long-term reliability.
Fig. 4-2 demonstrates two variations of the same basic
oscillator. The 600-Hz sawtooth at 4-2A would be useful in a
noncritical audio application such as a utility signal generator
modulator. A simple change in circuit configuration produces
the waveform in Fig. 4-2B. R„ was reduced in value to in¬
crease the frequency to 900 Hz. The steep wavefront of the
inverted and reversed sawtooth might find applications in trig¬
gering circuits.
+ 160V o- 1
600 Hz
i l 10V PK-PK
Rs i>>
6.8 meg'

c
= VI (C r) NE2
001 Mf"
4L J-
(A) Standard waveform. (B) inverted and reversed waveform.

Fig. 4-2. Variations in a sawtooth oscillator.

An improved triggering circuit is shown in Fig. 4-3. When

the NE2 ionizes, current flow through the 10K resistor reaches
maximum in less than 10 ^s. It then decays at an exponential
rate determined by the RC time constants.
The amplitude of the trigger pulse is dependent on the value
of cathode resistance R,;. The exact value of Rk is not critical

39
 TRIGGER
GENERATOR
2400Hz
5V PK-PK

Lk^

Fig. 4-3. Waveform generator with regulated supply.

and may be varied over a wide range to suit circuit require¬

ments.
A regulated supply may be combined with Fig. 4-3 to produce
the waveform generator in Fig. 4-4. The regulated supply
voltage is furnished by R„, VI and V2. Rss, R***, Cl, and V3
are the major frequency-determining elements, while Ru is
used to develop the trigger voltage that appears at point B.
Differentiating network, C2, XI, and Rd, provides a l-/xs posi-

Sometimes it is desirable to have the oscillator synchronized

as in Fig. 4-5. Normally R..s is adjusted to a frequency that is
slightly lower than 1 kHz, and the wiper of Rk is advanced
until the oscillator “locks in.” The sync pulse should be at least

40
 Rs

Fig. 4-5, Synchronized 1-kHz oscillator.

50 fx& wide, but it can be considerably less than the 10 V

illustrated.
A definite rounding of the sawtooth occurs as the frequency
increases. This effect is noted because the ionization time, the
deionization time, and the avalanche time now represent a
larger portion of the total period. If the frequency continues
to increase, the gas tube will eventually develop sine wave oscil¬
lations. The frequency at which this happens varies for dif¬
ferent gas mixtures and pressures, but all occur over 10 kHz.
These oscillations are quite unreliable and depend on critical
circuit values.
The experimental circuit in Fig. 4-6 was developed in an
attempt to increase high-frequency reliability. A power supply
tolerance of 10 percent is required but all other values are 20
percent. The LPA 27 has a gas mixture with the fastest avail-

Fig. 4-6, High-frequency sine-wave oscil¬

lator, 30-40 kHx.

41
able deionization time, and is the best choice for high-frequency
oscillators and waveform generators.
Deionization time is the limiting factor in reaching higher
frequencies. It might be said that anything encouraging ioniza¬
tion will inhibit deionization. The use of lamps having radio¬
active additives and emissive materials on the electrodes should
then be avoided in attempting to get stable high-frequency
operation.
Actually frequencies up to 90 kHz have been achieved but
the circuit parameters are too critical to be of any value. The
amplitude of the sinusoidal wave is difficult to predict. It will,
however, be quite small, ranging in value from 1 to 14 volts.

(A) Using two lamps. (B) Using one lamp.

Fig. 4-7. High-amplitude sawtooth generators.

If a high-amplitude sawtooth is required, the modes used in

Fig. 4-7 can be tried. When two lamps are connected in series
as in Fig. 4-7A the differential voltages will add to produce a
double-amplitude sawtooth. As many lamps as desired may be
connected in series, but since breakdown voltages also add, the
circuit has certain practical limitations. This type of oscillator
has found applications in electrostatic deflection systems and
relay energizers.
Fig. 4-7B uses a single lamp that has a considerably larger
differential, and is satisfactory in most cases, but the inherent
instabilities of high pressure gas exclude it from many critical
timing circuits. The T2-27-1WR500 will exhibit “voltage
jumps” that are visible to the eye. The corona will jump from
one part of the cathode to another, causing variations in the

42
maintaining voltage. These high pressure types (large dif¬
ferential), are best suited for “one-shot” operations, such as
timers, relay energizers, and counters.

TWO-LAMP MULTIVIBRATORS

Two neon lamps are frequently used to form a multivibrator

circuit. Fig. 4-8 illustrates the basic astable type which has a
peak-to-peak output voltage that is twice that of a single tube.
A quick analysis shows that if we assume VI to be “On” C
will attempt to charge to the supply voltage through R<s. When
point A reaches the breakdown voltage of V2, the lamp will fire
and the voltage at point A will be the maintaining voltage of
V2. The negative pulse generated by the drop in potential is
coupled through C to B, where it extinguishes VI. Now point
B begins to charge up while point A remains at the maintaining
voltage of V2. When VI fires, the process repeats, coupling a
negative pulse that is equal to the differential voltage of VI to
point A.
Since multivibrator circuits use two gas diodes, the upper
frequency limit is about 8 kHz. This is because the deionization
time limitations of both tubes are additive. Manufacturers
rarely incorporate gas tube multivibrators that operate over
2 kHz.
At very low frequencies, they are sometimes called flashers
and may be used for their visual effect. The amount of light
given off by the flash of a neon oscillator is determined by the
capacitor and the tube differential voltage. An increase in the
value of either one will raise the light output.

V?

V2

VI

43
 When the multivibrator is not being used as a flasher, R*
and R** should be as low in value as possible. This not only
lowers the output impedance but prevents parasitic oscillations.
If capacitances as small as 1 pF exist across the lamp, oscilla¬
tions are possible with resistor values over 2 megohms, assum¬
ing that rectified line voltage is used (+160 Vdc).
Lower value supply voltages allow for the use of smaller
resistances and a larger C. An ideal supply voltage is considered
by some to be one that exceeds the maximum rated EbMwil by
30 percent. If the supply voltage in Fig. 4-8 were reduced to
100 V and the two 2.2 meg resistors were changed to 51 OK,
the circuit would oscillate dependably at approximately 2 kHz,
and would be free of parasitics.
General Electric recommends that R* and RHli be below 1
megohm. This is not possible if high-frequency (over 500 Hz)
operation from a high voltage supply is required. An effective
alternative is to operate the oscillator from a regulated supply
as in Fig. 4-4. This calls for two more lamps and a resistor, or a
single neon regulator such as the Z100R12 and resistor.
The results that are pictured in this book using any of the
“NE” lamps were achieved by selecting lamps having average
characteristics. Pre-aged and selected versions, such as the
5AB series, would be a better choice, but tubes without emis¬
sive coating, such as the 55ST2A, would be recommended if
long term reliability is needed.
If we assume that both lamps are identical, and the series
resistors have the same value, the formula for frequency is:

f=■
Eafl|) + Ei,k<]wii — 2E„
2RC In
E„nn — Et,|>kdwn
where,
In is the natural logarithm.

The modified multivibrator in Fig. 4-9 has two cathode re¬

sistors and produces three symmetrical waveshapes. A triangu¬
lar wave is available between points A and B and has found
use as the sweep voltage in some X-Y recorders. The nearly
square wave found at point B has a rise time well under 10
/is, and the sloping top may be made flat by using the diode
clipper shown in Fig. 4-10.

44
 800 Hz

AvSAi

AAA
Fig. 4-9. Modified astable multivibrator.

Diode 1N38 has a positive bias of approximately 5 volts on

its cathode so it will not conduct until the square wave across
Ruk exceeds this value. When the diode conducts, clipping
occurs and the amplitude of the pulse is clamped to this 5-volt
level. The 1-meg linearity control is used to adjust the pulse
width.

♦ 160V

Fig. 4-10, Sguare-wave generator.

45
 Perhaps the simplest way of producing a high multivibrator
frequency is to use a common-cathode resistor. Fig. 4-11 shows
the waveshapes available from this type of circuit. The dis¬
charges of both VI and V2 are felt across Rh and a reversed
sawtooth occurring at twice the multivibrator frequency is
developed. Note that only on alternate cycles is the amplitude
equal. This is the result of the differences between the differen¬
tial voltages of VI and V2. Varying the frequency control R);,
will also affect the amplitude.

,hhhh
,N#M
f • 600 Hz

Fig. 4-11. Frequency-doubled, cathode-coupled, estable multivibrator.

The 3-range triangular-wave generator in Fig. 4-12 may be

used as a time base for any slow-scan device that needs equal
trace and retrace time. It is an astable multivibrator with the
components on the ground side of the neon lamps. The output
is taken from the 220k resistors, which aid in lowering the
output impedance. Ru and Rkk also provide a minimum amount
of resistance when R„» and R„ are at zero ohms. The 500k po¬
tentiometers may be ganged together as a frequency control,
or isolated so the linearity may also be adjusted.

FLASHERS
Neon-lamp oscillators are sometimes used as “flashers,”
which are on/off light sources that are found in signs, toys,
and advertising displays. The flasher circuits shown in this

46
book only touch on the possible configurations. A little experi¬
mentation will provide the user with endless variations.
Fig. 4-13 shows a flasher that will establish a regular se¬
quence, but initially the director of rotation cannot be pre¬
dicted. Once the pattern is established, it will not change unless
the power is removed and reapplied.
Another type of sequential flasher is illustrated in Fig. 4-14.
The sequence can be changed by varying Cl or C2. This flasher
is quite bright, as large values of capacitance are used.
The random flashers shown in Figs. 4-15 and 4-16 provide an
interesting pattern of blinking lights. The behavior of these
circuits is unpredictable. Even though each lamp is related to
each other lamp mathematically, the end result defies explana¬
tion. Fig. 4-16 may be considered an improvement over Fig.
4-15, in that it uses fewer parts and has the same number of
lights.

48
 Computer Circuits

Neon lamps are currently finding use in low-speed logic cir¬

cuitry. They are particularly useful in high-level applications
where the larger voltages are used to control thyratrons, relays,
etc. In addition, the neon provides a visible indication of state,
which in many cases eliminates the need for a separate visual
readout device.

BISTABLE MULTIVIBRATOR
The bistable multivibrator or flip-flop is considered the basic
binary computer circuit. Fig. 5-1A shows a gas-tube version of
this multivibrator with set and reset functions.
Initially, a zero potential is applied to the reset input. This
ground potential is coupled through the .2-^.F capacitor to point
B and if V2 is conducting, it is extinguished. Since there is
nothing to inhibit VI from ionizing, it will fire, causing a volt¬
age drop to be developed across Rk. When V2 was extinguished,
point B increased to the full 75 volts, which would again cause
ignition if it were not for the positive voltage at point C devel¬
oped by the common cathode resistor.
The voltage at point C is determined by the dividing action
of series circuit Rk, VI, and R*. VI drops its characteristic
maintaining voltage (50-60V) and the remaining potential will
be divided by Rk and R*. Increasing the value of Rk will place
V2 further into cut-off and allow the use of 20-pcrcent resistors

49
but the input pulse amplitude must also be increased to over¬
come this bias.
The multivibrator is now in a steady state and the T side is
lit. 1 is pronounced “not one” and indicates that no counts are
recorded in this circuit. Similarly 2 and 4 are pronounced, “not
two” and “not four,” respectively. Flip-flops that are driven by
the primary one can register these higher value counts. A 24-
volt positive pulse applied to the input will cause the flip-flop
to switch and the (1) side will be lit indicating a count of 1.
The (1) side will be lit once for every two input pulses which
means that the circuit counts by two (binary).

(A) Bistable multivibrator. (B) Monostable multivibrator.

Fig. 5-1. Multivibrator circuits.

A 24-volt positive pulse at point C will extinguish the con¬

ducting lamp and, since the nonconducting lamp has the high¬
est anode voltage, it will fire first when the 24-volt pulse is re¬
moved. The duration of the input pulse is determined by the
time constant of Rk and the .2-/U.F input capacitor. Switching
action is further ensured by the discharging action of the .5-frF
capacitor. This capacitor prevents the anode of the extinguished
tube from reaching a high positive voltage before the opposing
lamp can fire.

50
 Attempts to arrange flip-flops in counting chains without
the use of diodes or buffer amplifiers have for the most part
been unsuccessful. Careful design and a regulated power sup¬
ply can produce a two-stage binary counter, but additional
stages will almost certainly call for solid-state components.

MONOSTABLE MULTIVIBRATOR

The bistable circuit can be converted to monostable opera¬

tion by a change in resistance ratios. In Fig. 5-1B, VI is nor¬
mally on and V2 is held off by the voltage drop across Rk. A
24-volt positive pulse will extinguish VI and ignite V2 in the
usual manner, but Rss, which is the anode resistor for V2 is
large compared to RUl so the voltage developed at point C is
not large enough to hold VI in cut-off. VI will again fire and
the circuit will return to its stable state. The time that V2 re¬
mains on is determined mainly by the time constant of C, Rs,
and Rss.

THREE-INPUT OR GATE

The circuit in Fig. 5-2 is useful in converting high level logic

(+70V), to a value that is useful in solid state circuits
(+10V). X is normally at zero volts but will rise to 10 volts
if either A or B or C is +70 volts.
VI, V2, V3, and V4 are normally on and the voltage at point
N is lower than the lowest extinguishing voltage of the 5AB-B

51
 (50 volts). If any of the input lamps are extinguished, the
voltage at point M will increase. This will increase the conduc¬
tion of V4, and the voltage drop across the 680k resistor will
reach the maximum rated breakdown value. V5 then fires, and
the 10-volt output is taken from the 27k resistor. Removal of
the input voltage will cause V5 to extinguish.

THREE-INPUT AND GATE

An examination of the circuit in Fig. 5-3 shows that it is

basically the or gate, but with a change in the resistance
ratios. The resistance values are so chosen that VI and V2 and
V3 must be extinguished before the voltages at points M and
N rise to a value high enough to ignite V5. If any one of the
+•70 volt inputs is removed, V5 will extinguish.
If the 72k resistor is removed and the resistor values are
again changed, the AND gate can have full dc restoration. Fig.
5-4 illustrates this. The modified gate has a 70-volt output and
can be used to operate additional high-level gates. Circuit de¬
sign is more critical with this type of circuit because the volt¬
age at point M must vary over a range wide enough to break
down and extinguish V4 and V5 which are operated in series.

THREE-INPUT MAJORITY GATE

Recent concepts in computer logic are making use of the

majority gate, which will provide an output whenever the
majority of the inputs are satisfied.

52
 The glow-lamp version in Fig. 5-5 is again the same basic
“gate” circuit previously discussed. The resistance values are
so chosen as to cause the breakdown voltage of V5 to appear at
point N whenever 4-70 volts appears at any two of the three
inputs.

DESIGN CONSIDERATIONS

Speed is perhaps the most important limiting factor in neon-

lamp logic circuits. Flip-flops, monostables, and gates rarely
operate over 30 Hz, and delay time for some gates may be as
long as 3 milliseconds.

53
 Low series resistances should be used to prevent parasitic
oscillations and low supply voltages will prevent free running
operation of cathode-coupled multivibrators.
A relay coil is sometimes substituted for one of the series
resistances in the flip-flop or monostable circuits. If this is
done, lamps with a high differential voltage should be used.
If a circuit is to use off-the-shelf lamps that require no ad¬
ditional testing, consideration should be given to the minimum
and maximum voltage rating as given on the specification
chart. The 5AB-B was chosen in many circuits because it has
a 10-volt breakdown and 10-volt maintaining voltage range.
A voltage range this narrow is usually quite easy to work
with. The ranges do not overlap and an extinguishing voltage
test is included in the manufacture. The 5AB-B is also one of
the lowest cost circuit components available.

RING COUNTER

Perhaps the most useful of all the glow-lamp logic circuits

is the Manley-Buckley ring counter. It uses the decimal count¬
ing system and can easily count to 999 without a buffer ampli¬
fier. Counting rates of 500 Hz are possible and since there are
10 lamps for each decade, the lamps themselves can be used
for visual readout.
The basic circuit is illustrated in Fig. 5-6 and represents the
first three stages of a decade. When the reset button is de¬
pressed, the ground return path is removed from all stages but
the first, and VO will fire, indicating a count of zero. Current
flow is now through RK, VO, Dl, and Rl. VO will drop its char¬
acteristic maintaining voltage (60-70V), and the remaining
voltage is dropped by Rl and R«. This means that the poten¬
tial at point A can be anything from 92 to 100 volts, which is
well below the firing voltage of the T2-27-WR500, so VI and
the lamps that follow are held in a non-conducting state. When
the reset button is released, point B, which varies from +29 to
+33 volts, will charge Cl to this value through X2. If an input
pulse of zero volts is applied to point A through the .1 /xF ca¬
pacitor, V0, which was conducting, will now be extinguished.
The voltage at point A will again begin to go positive as Cx
attempts to charge to the supply voltage through Rl. VI will
be the next lamp to fire and will reach breakdown before point

54
A reaches 110 volts. This action occurs because Cl, which has
a 30-volt charge, cannot discharge through X2 when VO goes
out. Instead it makes the cathode of VI 30 volts more negative
than the remaining lamps, which assures earlier breakdown.
When VI fires, the process is repeated and C2 becomes charged
to fire the next stage.

Fig. 5-6. Maniey-Buekley ring counter.

The T2-27-WR500 lamps were chosen for this circuit be¬

cause they have a large differential, which allows the use of
10-percent resistors and a non-critical power supply. The lamps
in the illustration are operated at lower currents in order to
decrease their deionization time.
Gas tubes with a smaller differential, such as the 5AB series,
NE2, etc. are capable of faster counting rates, but the lamps
must be electrically matched and the circuit calls for tighter
resistor specifications. The 5AB type does, however, have
greater light output, which can be important if the lamps are
going to light numerals on a display panel.
Point A must be held below the rated extinguishing voltage
for a period long enough to allow for complete deionization.

55
The time it takes point A to reach any given value is deter¬
mined by the time constant of Cx and Rl.
Deionization time can be decreased if point A is not brought
all the way to zero volts but to some point more positive. This
value varies for different lamp types, so it is found experi¬
mentally.

TRIGGER CIRCUITS

The ring counter in Fig. 5-6 was triggered by applying zero

volts to the A-fiF input capacitor. When the circuit is stabi¬
lized, the voltage at point A is approximately 100 volts and
the input capacitor is charged. Cx must be discharged before
another count will be recorded; Fig. 5-7A shows one basic
method for accomplishing this.
The form C contacts of K1 allow Cx to be connected to point
A of Fig. 5-6 when the relay is operated. The sensor circuit,
which may be simply a switch, will operate the relay whenever
a count is to be recorded. When K1 is released, Cx will dis¬
charge through the 10k resistor and the circuit is ready for
another cycle. The 10k resistor is for contact protection and
should be small enough in value to allow for complete capaci¬
tor discharge. The speed of this circuit is restricted mainly by
the operate and release times of Kl. It is not practical to op¬
erate most relays over 50 Hz so the circuit in Fig. 5-7B can be
tried for higher counting speeds.
+ 13CV o—

TO SENSOR Kl
CIRCUIT
*sS
©
© ©

* TO P0INTI

FIG. 5-6
XI,
- IN 1763

.IMF
,003yF
' 10K
1 meg
VI ( ) T2-27-WR500

(A) Switched capacitor. (B) Gas tube.

Fig. 5-7. Basic decade ring triggers.

56
 Gas tube VI is operated under its minimum breakdown value
and is triggered on by a positive pulse at point B. This causes
a drop in potential at point C of at least 60 volts. The negative
pulse is felt at point A through Cx and the conducting tube in
the ring circuit is extinguished. C* and R1 of Fig. 5-6 must
now have a longer time constant since the voltage at A does
not drop as low as it did with switched capacitor operation.
Point A again starts to rise in voltage and continues until
the next tube in the ring fires. This new ignition causes a drop
in potential at point A that is coupled back through C* to point
C of Fig. 5-7B. This negative depression should be enough to
extinguish trigger tube VI and reset the entire circuit for an¬
other count. This type of circuit can be used for inter-decade
triggering, thereby eliminating the need for buffer amplifiers.
A practical circuit that is operated by switch closures is
shown in Fig. 5-8 and was designed for the complete ring
counter shown in Fig. 5-9.
The .001 capacitor is charged to about 45 volts by volt¬
age-divider action and when the count button is depressed, the
rapid drop in potential at point B will cause C to attempt to
discharge. Since XI blocks one discharge path, the --45 volts
is felt on the cathode of VI and causes ionization. HI in the
counter and Cx were both increased to the values shown, to
lengthen the time constant.

57
58
ALL LAMPS T2-27-WR5O0 OR HPN-27-1
ALL DIODES 10CV PIV @ 50mA OR BETTER

Fig.
5-9.
Complete
decade
ring.
TO TRIGGER OF
NEXT DECADE
 COMPLETE DECADE RING

The decade illustrated in Fig. 5-9 has ten identical stages,

as discussed earlier. It also has a carry function that permits
the decade to be reset to zero and operate the trigger stage of
the following decade.
When V9 is extinguished by the tenth pulse, the rise in po¬
tential at point (T) is coupled through Cc to the anode of VO
and through C(. and CT to the trigger stage of the next decade.
Two Z82R10 miniature neon regulators operated in series
will provide a regulated 164 volts ±2 volts for the counter and
trigger circuits. An eight-decade counter can be operated from
these two tubes, thereby eliminating complex circuitry. The
power supply potential is not critical, but it must always ex¬
ceed the lamp maximum-rated breakdown voltage.

59
 Miscellaneous Circuits

SCR CONTROL

Silicon controlled rectifiers or thyristors are best controlled

when they are provided with a discrete trigger pulse. The gate-
to-cathode circuit of the SCR in Fig. 6-1 is in series with VI
and the turn-on pulse will be generated when the lamp fires.
VI, together with C and Rl, forms a one-shot relaxation os¬
cillator that is operated at some point on the positive portion
of the 60-Hz sine wave. The exact operating point is deter¬
mined by the setting of Rl, sometimes called the “Speed Con¬
trol.” The value of C is made large enough to supply ample
gate current and the neon tube was selected for its 60-mA peak-
current capability. Most manufacturers recommend the Ik
resistor (R2) for predictable gate turn-on characteristics. The
effect of R2 on the oscillator circuit can be ignored.
With the HI-LO switch in the HI position, the negative half
of the sine wave is allowed to conduct through the load at
socket Ml and the MR990 diode XI. The positive half is con¬
trolled by the SCR and oscillator circuit, and since the break¬
down voltage of the neon tube represents approximately 30
degrees of the sine wave, the load can never be turned com¬
pletely on (360 degrees). This 30-degree loss represents little
power, so the effects are negligible.
When the HI-LO switch is in the lo position, 30-180 degrees
of the ac cycle may be applied to the load. Diode XI is con-

61
nected in the reverse direction across the socket, so the con¬
ductive path for the negative alternation has been removed.
Diode XI now becomes a “free-wheeling” diode and helps
reduce the “cog-wheel” effect common to motors that are
pulsed-on with short bursts of current. This is done by pro¬
viding a discharge path for the magnetic field that exists in
the motor windings when the SCR shuts off. The collapsing
magnetic field induces a current through the diode and motor
windings that is in the same direction as the original, thereby
minimizing abrupt changes in power. XI also provides the
SCR with protection from transient voltages in both positions
of the switch.

RELAY CIRCUITS

Gas tubes have been used to energize relays since the early
1930’s, but originally this was limited to thyratrons because of
their higher current capabilities. Miniaturization and the mass
production of sensitive relays in later years allowed the use
of T2 neon lamps.
Most neon-operated relays constitute some part of a thresh¬
old circuit. In Fig. 6-2A the minimum rated breakdown of VI
is 140 volts so K1 cannot operate until this potential is reached.
When VI does ionize, it will drop its characteristic maintain¬
ing voltage and the remaining voltage is dropped across Kl.

62
 (A) Single tube. (B) Multiple tube.

Fig. 6-2. Threshold relay energizers.

This is approximately 75 volts, enough to operate the relay.

In effect, the relay is operated by the differential voltage of the
tube, unless the power supply is going to increase to some
greater value. The relay will release whenever the dropout
current is reached, or when the lamp extinguishes.
Neon lamps may be operated in series to reach higher volt¬
age levels as shown in Fig. 6-2B. Long-cathode indicator types
were used in this case because of their lower cost and higher
current ratings. Since differential voltages as well as break¬
down and maintaining voltages add in a series circuit, a relay
was chosen that would operate on the lowest differential and
not be damaged by the highest. The Automatic Electric Type E
satisfies both requirements and may be used with two form C
contacts. The bifurcated contacts are rated at 4 amperes.
Fig. 6-3 illustrates a circuit that uses a sensitive, balanced-
armature relay that will operate on less than 2 mA. K1 is in
series with Vl and connected across part of a voltage-divider
network. The position of the set control dictates what poten¬
tial must be applied to point B before point A reaches the lamp
breakdown voltage. Rs and the resistance of the coil are low
enough to allow pull-in current to flow after breakdown.

63
 Larger relays may have pull-in currents as high as .5 am¬
pere. If threshold operation of these types is needed, the cir¬
cuit in Fig. 6-4 can be tried.

A transistor should be chosen that can furnish the relay op¬

erating current and withstand the power supply voltage Ec.
Low-leakage silicon types would be a good choice for the cir¬
cuit shown, since the base of Q is not returned to ground.
E(. can be any value above the rated relay voltage but exces¬
sive voltages will increase the amount of power dissipated
by Q.

64
 To find !>, use the formula:

j _ Relay current
“ ~~ Transistor beta

To find R, use the formula:

D __ Neon differential
R “ I,x2

Diode XI is included to protect the transistor from the

counter emf generated by the relay. Time delays can be incor¬
porated in the circuit by connecting a capacitor between point
A and ground.

A mercury relay is used in the multivibrator circuit of Fig.

6-5 for extended life (over 1 billion operations). The high re¬
sistance coil is used for increased sensitivity and is operated
by V2. The ratio of RH to RBS, and the relay coil resistance
(3300 ohms), were chosen to keep the relay de-energized five
times longer than it is energized.
Fig. 6-6 shows one variation of a memory or latching cir¬
cuit. VI is held below its minimum breakdown voltage and
cannot ionize until a negative pulse of sufficient amplitude is
felt on the cathode. The potential difference between this pulse
and the supply voltage must equal the maximum rated break¬
down voltage of the tube.
The circuit will “remember” a switch closure when the
.001-juF capacitor discharges through the 56k resistor, the

65
 * 135V o

Fig. 6-6. Relay memory.

switch contacts, and the tube to produce breakdown. Diode

XI prevents the capacitor from discharging through the coil
of the reed relay, which would inhibit firing by providing a
shunt path. Xl can be any commercial-grade component with a
200-PIV rating. The supply voltage is high enough to sustain
ionization, so the current flow' through VI, XI, and K1 will
keep the relay energized until the + 135-volt supply is removed.

PHOTOCELL CIRCUITS

Photoconductive cells that operate on the bulk effect are

usually made of cadmium selenide (CdSe), or cadmium sulfide
(CdS). Both materials can be considered as a pure resistance
whose ohmic value depends on the amount of light falling on
its surface.
CdSe and CdS cells can each be operated by glow' lamps, but
CdSe has a peaked response in the 7000-angstrom region, so it
is more sensitive to the light radiated by the ionized neon gas.
Greater efficiency is obtained by using high brightness lamps
that produce more lumens per milliampere.
Most of the lamp-photocell combinations discussed in this
chapter are mounted end-to-end as in Fig. 6-7B. The cell is
placed in the tube and the end is sealed with silicon rubber.
The neon lamp is then put in the other end and should touch

66
the photocell before the sealer is applied. Since this makes a
moisture-proof, light-proof module, lamps are used that have
been compensated for dark-effect.
Clairex Photomods and Raytheon Raysistors have similar
mounting schemes providing over 1000 megohms of isolation
between the lamp and photocell.
SI

+160 Vo— o
CLAIREX

?4K

VI
C2A

(A) Schematic.
ALUMINUM
LAMP TUBING
vLEADS 1/4" INSIDE
DIAMETER

(B) Typical mounting.

SILICONE
RUBBER '

PHOTOCELL LEADS
Fig. 6-7. Isolation photoswitch.

Fig. 6-7A is an isolation switch that has a contact resistance

of 500 ohms. It is operated by the light from VI when SI is
closed. The noise and transients associated with mechanical
switches are minimized since there is no contact bounce and
the photoconductive material does not change state rapidly.
This latter feature is useful in interrupting inductive loads.
The lamp-photocell module has also been used as a voltage-
controlled resistor. In Fig. 6-8 a 2.3 to 1 voltage change can
produce a 5 to 1 resistance change. A more popular version of
this circuit is the current-controlled resistor or “isolation po¬
tentiometer.” Rs is replaced with a 250k potentiometer and the
current of VI is varied to produce the desired output value.

67
 no TO + ?5CV
o

CLAIREX
603A

Fig. 6-8. Voltage-conlrollod resistor.

Resistance ratios of 10,000 to 1 are possible, using this method,

without the inherent noise of the slider arm.
Photochoppers are similar to relay choppers in that they
offer a number of contacts that open and close at some prede¬
termined frequency. The circuit in Fig. 6-9 shows four mod¬
ules connected to form a 20-Hz astable multivibrator. It can
be used to provide synchronous spdt service in voltmeters and

68
chopper-stabilized power supplies. Low noise and long life are
again the features of this type of circuit. Photochopper fre¬
quency is presently limited to X kHz maximum. This is due
mainly to the response time of the photocell.
A more efficient circuit would eliminate V2 and V4 so the
remaining photocells could be mounted in a manner that would
have VI and V3 driving two cells each. The 1-^F capacitor can
be removed for 110 Vac operation if diodes are placed in series
with the lamps. The diode in series with VI should have a

polarity that is opposite to the one in series with V3. One lamp
will conduct when the line goes positive and the other will con¬
duct during the negative alternation. Commercial versions of
the ac driven chopper are Clairex CM-2, Leeds and Northrup
354256, and Airpax 5510.
Photocells can be made to operate neon lamps if both are
part of a voltage-divider network. In Fig. 6-10 the SENS
control will determine how much light must strike the photo¬
cell before its resistance is low enough to cause the breakdown

69
voltage of VI to appear at point A. A useful variation of this
circuit is to interchange the sens control with the photocell so
the relay will be activated by darkness instead of light. The
two 5k resistors are protective devices for the photocell.
The circuit in Fig. 6-11 is classified as experimental because
it has not been fully developed nor has it found popular use.
It demonstrates the little known principle that sine-wave am¬
plification is possible using a wide range photocell in conjunc¬
tion with a neon lamp.

VI is mounted in a light-proof enclosure at right angles to

the cell, in order to expose as much electrode to the CdSe as
possible. The incoming 60-Hz sine wave is coupled to the 15k
resistor through the 2-/aF capacitor. This varies the lamp cur¬
rent, causing a modulated light output. The resistance of the
photocell varies over a wider ratio than the lamp current, so
amplification is possible.
The output is taken from the voltage divider at point A. For
maximum amplification, this point is adjusted by the 50k con¬
trol to half the supply voltage. VI is operated at very high cur¬
rent, so a short life will result. Perhaps different mounting
schemes, such as a cluster of four cells connected in a series/
parallel arrangement around the lamp, would result in lower
operating currents. Changes in photocell geometry and lens
arrangements also might improve the response.

70
 PHOTOCONDUCTIVE JUNCTION DEVICES

Host solid-state component manufacturers now offer a va¬

riety of junction devices that can be operated by a gas lamp.
The list includes diodes, SCR’s, FET's, and transistors. In each
case a pn junction is “switched on” by an external light source.
The response time of these types is very fast, but higher input-
light levels are needed since the junction area is relatively
small. Many of these photo junctions have a spectral response
peaked in the 8000-angstrom region, so an argon-filled lamp
can be used.

TEMPERATURE AND HUMIDITY SENSORS

The light threshold circuit in Fig. 6-10 can be modified to

operate on some chosen temperature or relative-humidity level.
The photocell is replaced with a thermistor or humidity sensor
and the value of the SENS control is selected to match the range
of the new device.

TIMER CIRCUITS

Gas-tube timing or delay circuits can be regarded as varia¬

tions of the basic oscillator circuit. The difference is that the
series resistance must be made small enough to keep the lamp
ionized after the capacitor reaches striking voltage. Fig. 6-12
illustrates the basic circuit. Rs was chosen to provide the op¬
erating current for the relay and to sustain ionization. Under
these conditions a delay of over 20 s would call for a 1000-//F,
200V capacitor. A component of this size would be both expen¬
sive and bulky, so the approach used in Fig. 6-13 might be
more practical.
VI, Kl, V2, and Xl form a circuit that is similar in many
ways to a thyratron or even to a unijunction transistor. The
ground side would be the cathode, or base 1, and the high side
would be the anode, or base 2. Point A would then be the grid,
or gate.
The breakdown voltage of both tubes in series is higher than
the supply voltage, so the lamps initially are in a nonconduct¬
ing state and XI prevents VI from ionizing through C. When
SI is put in the start position, the voltage at point A will rise

71
 Fig. 6*12. Basic timer circuit.

VI

IOOOmF
Cl
20(N

r:
exponentially until V2 fires. The maintaining voltage of V2
plus the breakdown voltage of VI is well under the +160V sup¬
ply so VI will also ionize and energize Kl. The resistance of
K1 is 10k, and no additional current-limiting resistor is needed.
si

72
 Unlike the case of the unijunction transistor, the applied
power must be removed before K1 will release. This is done by
putting SI in the RESET position and simultaneously discharg¬
ing C through the 10k resistor.
Fig. 6-14 shows another method of isolating the timing cir¬
cuit from the operating circuit. Point A is held slightly below
the lamp’s rated breakdown potential and the tube remains
extinguished. When SI is switched to start, the voltage at
point B will begin increasing in value at a rate determined by
C and the programmable resistor input. VI will conduct
through isolation diode Xl when point B reaches breakdown.
Ionization will be sustained by current flow through isolation
diode X2 and R(>.

si

Fig. 6-14. Programmable timer, 100,000 ohms per second.

If the breakdown voltage of VI is 63 percent of the supply

voltage, then it can be said that the tube will fire in one time
constant. A 90ST2S was used in this example, but greater ac¬
curacy can be had by hand-selecting a pre-aged high-brightness
lamp for a 100.8-volt breakdown. The capacitor and resistor
values should have a close tolerance and the diodes can be any

73
replacement-grade component rated for 200 PIV at 100 mA
or better.

TOUCH CONTROL
Body capacity can be used to operate the circuit in Fig. 6-15
by briefly providing a conductive path to ground. The circuit
consists of a bistable multivibrator that is triggered by bring¬
ing the hand in contact with the touch points. XI is rated at
200 PIV, 100 mA.

The circuit works well under most conditions, but enough

body capacity must exist between the touch point and circuit
ground. The eai'th side of the power line should be connected
to the circuit ground if an ac/dc supply is used. If an isolated
or battery supply is used, the touch point might have to be
made physically larger and the circuit ground should be an
actual metal chassis, not a circuit board or terminal strip.

AUDIO SWITCH
VI in Fig. 6-16 acts as a high resistance in the nonconduct¬
ing state and prevents the audio from being transmitted to

74
 AUDIO
OUT

the output. A +72V level at the pate input will fire VI, and the
ionized gas will now act as a low-impedance path for the ac
signal.
Miniature neon lamps are cold-cathode devices, so the cur¬
rent flow will change rapidly with voltage variations. The
lower frequency response is determined by the value of the
coupling capacitors, and the high end is a function of the gas
and the current through the lamp. The circuit shown works
through most of the audible spectrum, so smaller capacitors
can be used for communications channels (300-3000 Hz.).

VARIABLE DELAY CIRCUIT

Transmission time in a gas tube is a function of tube oper¬

ating current, so changing the value of the series resistance
will also change the delay. The ganged controls in Fig. 6-17

DELAYED
OUTPUT

75
can be adjusted to give delays over the range shown. Two po¬
tentiometers are used in this case to provide an output pulse
of constant amplitude.

OVERVOLTAGE CIRCUITS

Arc suppression is usually necessary to protect the device

that controls an inductive load. If the current to an inductor
is interrupted by switch contacts, the coil will generate a
counter emf that may exceed several thousand volts. The exact
value of the generated voltage depends on the inductance of
the coil and the magnitude of the current. This inductive “kick-
back0 causes arcing at the contacts and leads to a shorter
switch life.
High amplitude voltages can, of course, permanently dam¬
age semiconductors, so if the switching component is a junc¬
tion device, the voltage problems still exist. An arc suppression
circuit for solid-state components is usually referred to as an
overvoltage circuit.
Fig. 6-18A uses a neon lamp to limit to a safe value the emf
generated by relay Kl. The breakdown and maintaining volt¬
age is chosen to be above El( so the lamp is normally exting¬
uished until the current to Kl is interrupted. The high back¬
ward voltage generated by Kl ionizes VI and the potential is
held to the maintaining voltage of the neon lamp. If a mechani¬
cal switch is used to operate Kl, then almost any neon lamp
will protect the contacts, but again the maintaining voltage in
a dc circuit must be above Eh or the lamp will be destroyed
after ionization.
High-current relays such as solenoids require special lamps
because the collapsing magnetic field in these types can gen¬
erate enough energy to destroy a simple A1A lamp. Under
these conditions, the tube’s energy-transfer rating should be
considered. In general, the lamp types that can transfer the
most energy are the ones with the highest voltage differential.
Sometimes, as in dc power supplies, the switch contacts are
of little concern and the attention is focused on the solid state
components, Silicon and germanium devices have strict volt¬
age ratings that should not be exceeded.
The novel lightning arrester in Fig. 6-18B acts as an open
circuit until the breakdown voltage of any one of the three

76
lamps is exceeded. Since no performance data are available,
and it is doubtful whether the circuit would provide complete
protection against a direct strike, it should only be used in
conjunction with a conventional lightning arrester. One appli¬
cation of this device is the protection of TV or radio front ends
from nearby transmitters.

(A) Single lamp with relay. (B) Three-lamp lightning arrester.

(C) Overvoltage protection in a power supply.

Fig. 6-18. Overvoltage circuits.

Overvoltage protection for a typical power supply is con¬

sidered in Pig. 6-18C. V7 is used to protect the diodes from
the counter emf generated by LI when S2 is opened. This lim¬
its the use of V7 to power supplies under 50 volts.
V6 at point B is across the secondary of the transformer
and sees only ac, so the maximum rated potential at point B
should be around 40 Vac. Point B is a preferred location since
it provides overvoltage protection for diodes with a PIV rat¬
ing as low as 75 volts. The output voltage can be any value
under 50 volts. V6 suppresses the high-voltage peaks generated

77
when SI is opened and also suppresses high-voltage line tran¬
sients.
Probably the most popular suppresser location is point A,
which is directly across the primary. The A051 and HPN-27-1
were manufactured specifically for line-voltage service but
other types can be used, such as the T2-27-1WR760 or even
two high-brightness indicators in series. The basic require¬
ment is that the breakdown voltage must be higher than the
peak line voltage (165V). V5 is effective against transients
and lengthens the life of SI, but it does not give the same de¬
gree of diode protection from transformer voltages as V6.

78
 7

Power Supplies and

Instruments

UNREGULATED 160-VOLT SUPPLIES

Fig. 7-1 shows two power supplies that can be used to oper¬
ate most of the circuits discussed in this book. The full-wave
version is, of course, the preferred circuit, since it has a lower
ripple content and offers isolation from the power line. Some¬
times a 1:1 isolation transformer is available and full-wave
rectification can be had by using a bridge across the untapped
secondary. This latter solution is popular for load currents in
excess of 100 mA.

REGULATED POWER SUPPLIES

The regulated power source in Fig. 7-2 is made from a half¬

wave voltage doubler, a neon regulator, and a zener diode. This
supply can be used for neon oscillators, timers, ring counters,
and other devices that need a stable 160/164 volts.
Vacuum-tube regulators operate by changing their internal
resistance when the bias is varied. In Fig. 7-3 both circuits
use the maintaining voltage of the neon lamp as a reference for
one of the control electrodes, while the other control electrode
is connected to a point that reflects voltage changes in output.
Series tube V2 can furnish more power at greater efficiency
than shunt regulator V4, since the current through V4 is lim-

79
 <> 157-172 V i® 10mA
+
1= ^OmF <>MU 153- 168V 0 30mA
200V
1 L _
(A) Half-wave.

DIODES: IN 1763
Tl: 250VCT <® 25mA
(KNIGHT 5*1 E2003 OR EQUIVALENT)

(B) Full-wave.

Fig. 7-1. Unregulated supplies.

ZENER: ALLIED Z439358 (3.9V) -O *164V

REGULATED

REGULATED

no -120
VAC X2i i IN 1763 e =J 40|JF

o
350V AsV2
W Z82R15

r _1_u uumiTiuii
--»-
Figl. 7-2. Neon-regulated supply.

(A) Shunt regulation. (B) Series regulation

Fig. 7-3. Basic vacuum-tube regulators.

 SERIES REGULATED 160/164 VOLT SUPPLY
.5% REGULATED, 0-25 n?A

ited by the ratings of V3 (15 mA max) and the value of R,|.

In spite of this the series circuit is rarely used by itself
because it is not as sensitive to voltage changes. The shunt cir¬
cuit, however, has better regulating action and is used ex¬
tensively to regulate high voltages at low currents. The main¬
taining voltage of the lamp, or lamps, plus the maximum rated
plate voltage of the tube will determine the maximum voltage
that can be regulated. A scheme similar to this is used to regu¬
late the high-voltage supply of color television receivers.
Both types of regulators can be combined as shown in Fig.
7-4. Voltage changes in the load are sensed by the shunt pen¬
tode, which amplifies the error and drives the series-pass tri-
+ 30OV SERIES-REGULATED VARIABLE SUPPLY
UNREGULATED 100-200 VOLTS, 0-40mA, 1* REGULATION

81
82
ode. Current to V2 is supplied through R„ which improves
regulation by making the voltage drop across V2 independent
of the cathode current of the pentode.
Higher current and a wider voltage range are available from
the circuit in Fig. 7-5. Screen-grid regulation has been added
to the shunt tube, and ripple control is provided by Rf and C.
Fig. 7-6 is a complete low-cost power supply intended for
the shop or for testing glow lamps. It uses a small transformer
and two miniature tubes. One-half of the 6GH8 is connected as
a diode and used to develop a rectified negative voltage for the
cascaded neon lamps. V3 keeps the cathode of the shunt tube at
—60 V or more so the output voltage can be adjusted all the
way down to zero. V4 is ionized by the 220k resistor and can
be brought out to the front panel as an indicator. T2-32-1
lamps were chosen for V3 and V5 because of their higher cur¬
rent capability but any standard-brightness indicator can be
used that has low breakdown and maintaining voltages. The
zero control is used to adjust the output to zero volts when
the volts control is in the extreme ccw position. If the lamps
have not been pre-aged the output will drift slightly, so the
power supply should be left on for at least 72 hours before this
adjustment is made.
Fig. 7-7 is a set of regulation curves for the power supply
shown in Fig. 7-6.

VOLTAGE CALIBRATORS

Miniature neon regulators can be particularly useful as a

source of precision voltages. The calibrators shown in the
illustrations offer a few of the possibilities, and were designed
with economy as the prime consideration.
Fig. 7-8 is a simple dc calibrator that offers 1 percent accu¬
racy when the potentiometer arm is in the extreme cw posi¬
tion (100V). A pointer knob on the shaft selects the desired
voltage from a calibrated dial, which in this case is a trans¬
fer letter switch pattern. Ten of the twelve switch positions
are used since this corresponds to the standard 294 300-degree
potentiometer such as the Mallory M10MPK. As the pointer is
moved in a ccw direction the accuracy is derated by the dial
markings, the linearity of the control, and the impedance of
the load, which now forms a voltage divider with the poten-

83
 Fig. 7-7. Regulation curve for 0- to 275-volt supply.

tiometer. Diode X2 is included to null out the voltage drop

caused by shunt-starting diode XI.
Higher accuracy is available from the instrument shown in
Fig. 7-9, Linearity and dial-marking errors are eliminated by

Fig. 7-8. Utility d« calibrator, 0 to 100 volts.

84
 low

5W

25V

lW

5V

2V

IV

.5V

.IV

using a fixed voltage divider, and since the 100 volts is adjusted
precisely by the cal control, the accuracy of this source is de¬
termined mainly by the tolerance of the resistors used in the
divider and by the external loading. The cascaded section pro¬
vides increased stability and it should be noted that while
there is a current of 10 mA through the divider there is a cur¬
rent of only 2 mA through the A1A lamps.
Digital readout is the feature of the reference supply shown
in Fig. 7-10. A turns-counting dial and a 10-turn potentiometer
combine to give a precise source of continuously-variable volt¬
ages. The value of R was set at 50k since many high-voltage
circuits can be made inoperative by a low impedance. The
value of R can be increased to any desired value without fur¬
ther circuit changes, but if the instrument is to be used strictly
for calibration purposes and a lower resistance is needed, then
Rs will have to be decreased in value and the SET control re¬
adjusted. Actually the SET control would be unnecessary if
pre-aged circuit component lamps with guaranteed voltage
characteristics w’ere used in place of the seven AlA neons.
These lamps were used as a matter of convenience, but their
wide range of voltage characteristics makes the 25k adjust¬
ment necessary. Initially the circuit should be interrupted at
point A and a milliammeter inserted while the set control is
adjusted for a meter reading of 2 mA. The procedure is re-

85
peated after 72 hours of operation. BNC connectors are used
in the output but binding posts or a combination of both may
be more suitable. The BNC connectors must be insulated from
the chassis by a fiber washer or similar device.
One interesting use for the digital calibrator is the precise
measurement of peak-to-peak waveforms. If the waveform to
be measured is applied to one vertical input of a dual-trace dc
oscilloscope, and the calibrator output is applied to input num¬
ber two, the calibrator can be adjusted to cause a base line to
touch one peak of the waveform. The voltage reading is re¬
corded from the digital dial and the calibrator is adjusted to

86
move the base line to the opposite peak of the waveform. The
difference between the latter reading and the first reading is
the peak-to-peak voltage of the waveform. If the oscilloscope
has an algebraic addition circuit, it can be used with the cali¬
brator to measure differences as small as 100 mV on a 250V
pk-pk waveform.
Fig. 7-11 shows a high-stability ac calibrator with a vernier-
dial readout. When the dial is attached to the potentiometer the
control can be varied for only 180 degrees of the possible 300.
This means that the shaft should be in the extreme ccw posi¬
tion and the vernier dial set at zero when the two components
are secured to each other. The dial is then rotated to 10 and
the CAL control is adjusted for a 10-volt pk-pk output.

X2

Fig. 7-71. Ac calibrator, 0- to 10-volt range with vernier readout.

The positive half of the ac sine wave is applied to point A

through a diode and the 6k resistor. Normally this point could
reach 160 volts, which is the peak value of one half of a line-
voltage alternation, but voltage-divider action with the two
potentiometers and the 8.2k resistor limits the maximum possi¬
ble voltage at this point to 115 volts. Under the conditions
shown in the illustration, point B is at 82 volts and diode XI
will conduct when point A exceeds this value. In effect, point
A can never exceed 82 volts because of the clamping action of

87
diode XI. Point A then, has an 82-volt square wave that is
divided down to a usable ten volts for the decade dial. An isola¬
tion transformer similar to the one shown in Fig. 7-8 should
be used at the input.
The calibration circuit of Fig. 7-12 can be used to adjust
the output of precision voltage sources such as the one shown
in Fig. 7-9. R1 is inserted and the voltage to be calibrated is
adjusted for a meter reading of zero. Any nulling device,
bridge, or VTVM with a zero-center feature can be used in
place of meter Ml. R1 is found by the following formula:

R1 = 10,000(E - 2)
Where,
E is the desired voltage in volts.

The 0.3-percent accuracy is based on the use of a 0.1-percent

tolerance multiplier.

WULTIPLfER RE5IST0R

TRANSIENT VOLTMETER

Neon-lamp voltmeters appear in many forms on the market,

but their major use has been limited to handymen and hobby¬
ists since the accuracy of these types is usually quite poor. Dif¬
ficulty in stabilizing the breakdown voltage is perhaps the
main reason, but there are many others. The circuit in Fig.
7-13 is included because it can perform a function that digital
and D’Arsonval meters cannot. As the name implies, it can be
used to measure transients that last for less than lOOfis. This
is particularly useful in circuits that combine solid-state com-

88
ponents with inductors, as, for example, a circuit using re¬
lays and diodes. If the voltmeter input is connected across the
relay coil, the calibrated knob can be rotated until the de¬
energization of the relay causes the A083 to light. Calibration
marks on the knob skirt will give the approximate value of
the transient generated by the relay and the engineer can now
determine the voltage ratings for the diodes. Initially the
VOLTS control is put in the extreme ccw position and the 0-10

knob-skirt markings are positioned in such a manner as to

place the numeral 1 opposite the chassis indexing mark or dot.
1100 volts will read off-scale.

VOLTS
LINEAR lmeg •CW
O—

CALIBRATED KNOB A083

MILLEN HRS 3 VI
Fig. 7-13. Transient voltmeter, range '00 to
OR EQUIVALENT
1100 volts.

INPUT 100K -

2K ■

ELECTRICIAN’S FRIEND

A simple and useful service tool is shown in Fig. 7-14. It can

be connected to any power main or junction box and will tell
the user at a glance what the line voltage is and whether it is
ac or dc. The ac lamp will light only on ac and the dc lamp will
light only on dc. The lo lamp will come on at 70 Vdc or 50 Vac
and the 110 and 220 lamps will come on at their rated voltages,

Fig. 7-14. Circuit for the Electrician's Friend.

89
ac or dc. Actually the 220 lamp will come on at 210 volts since
this is usually considered acceptable.

HIGH-ENERGY DETECTOR

Fig. 7-15 shows a homemade version of several commercially

available high-voltage probes. High-voltage or high-energy rf
fields will ionize the NE51 directly and cause the gas to glow,
making it useful for many go/no-go applications. It can be
brought close to the output circuit of a transmitter and the
tank circuit can then be adjusted for maximum brightness of
the lamp. When the probe is held near a television flyback
transformer it will give the repairman a quick indication of
the presence of high voltage, and positioning the lamp near a
spark plug wire will indicate whether the plug is firing or not.

A-M SIGNAL GENERATOR

An af relaxation oscillator is used to shock excite the tank

circuit in Fig. 7-16. Any a-m radio knob that has frequency

IN 1763 T2-27-WR350
XI 1QOO 2meq VI 8TURNS OF HOOKUP WIRE

FERRITE 10-365 pF 9-180 if

ANTENNA
Fig. 7-16. Junk box a-m signal generator, range 455 to 1650 kHz.

90
markings on it can be used as the dial for C2. Cl is a trimmer
and C3 can be switched in for 455 kHz. The radio can be sev¬
eral feet from the generator and the output will still be ample
for alignment purposes. Several ferrite antenna types were
tried and all worked equally well. The frequency of the audio
oscillator should be over 1 kHz for reliable operation. With SI
closed, and C2 set for maximum capacity, C3 is adjusted from
minimum capacity until a tone is heard in a radio that is cor¬
rectly aligned. C3 is now set for 455 kHz and the output should
easily penetrate the input stages of 5-tube radios and most
transistor types, so no direct connection is necessary in align¬
ing the i-f’s.

91
 Reference Section

LIGHT OUTPUT

Standard-brightness lamps radiate energy in the 5200-5400,

5700-7500, and 8200-8800 Angstrom bands with an average
overall efficiency of .06 lumen per milliampere.
High-bHghtness lamps operate in the 5700-7500 and 8200-
8800 Angstrom bands with an overall efficiency of .15 lumen
per milliampere.
Argon lamps radiate in the 300-4700 (near ultra-violet) and
5500-9500 Angstrom bands.
Helium-argon lamps have three minor radiation bands be¬
tween 3400-6400Angstroms and a major energy output be¬
tween 7000-9000 Angstroms.

SHUNT CAPACITANCE AND

INTERNAL RESISTANCE

The shunt capacitance for an extinguished glow lamp varies

from 0.5 to 1.5 pF, depending on the size of the electrodes and
the pressure of the gas.
Dynamic internal resistance figures vary widely and de¬
pend on four main parameters: the type of gas, the gas pres¬
sure, the electrode material, and the operating current. Of
these, the operating current is of the most concern. A lamp
operating at under 1 mA will usually have a dynamic resist¬
ance of over 4000 ohms, whereas a lamp operated at 10 mA
may have a resistance of 500 ohms. As a general rule, lamps

93
of the same designation will have internal resistances that are
within 1 percent of each other.
Internal resistance figures are not included on specification
sheets because in most cases the values are insignificant. The
A1A, for instance, has a characteristic resistance of 5500
ohms at design current, and when it is operated at line volt¬
ages, it uses a 220k series resistor. Since 5.5k is less than 3
percent of 220k, and the series resistor is usually a 20-percent
type, the internal resistance can be ignored.
It is for this reason that the formulas in the preceding chap¬
ters do not include internal resistance. If, however, the supply
voltages are close to the maintaining voltages, then the inter¬
nal resistance can represent an important part of the whole.
In this case, the internal resistance .should be subtracted from
the calculated value to arrive at the correct value of series
resistance.

DRI-FILM COATING AND LEAKAGE

All neon lamps have a leakage resistance in the 1000-meg¬

ohm region under ideal conditions, but when the relative hu¬
midity increases and moisture condenses on the lamp, an ex¬
ternal conductive path is provided.
A commercial coating that is furnished on some lamps and
referred to as Dri-film by GE causes the moisture to collect
in little puddles in a manner similar to rain puddles on a
freshly waxed car. Since these small puddles do not touch each
other, the resistance remains high.
The recommended method for measuring leakage resistance
is to apply 40 volts to a lamp in series with a microammeter.
The resulting current will indicate the leakage under dynamic
conditions. A reading of 0.4 microampere would indicate a leak¬
age resistance of 100 megohms, which is a standard figure in
the industry.

AGING PROCEDURES
Standard-brightness lamps—Twenty-four hours at 2 times
the design current, followed by 24 hours under typical circuit
operating conditions.
High-brightness lamps—Fifteen minutes at 15-17 mA, fol¬
lowed by 24 hours under typical operating conditions.

94
 Large-differential (high-pressure types)—Four hours at 3
times the design current, followed by 24 hours under typical
circuit conditions.
High-current types—Twenty-four hours at 15 mA, followed
by 24 hours under typical operating- conditions.
The foregoing procedures have found wide acceptance by
the electronic industry and are recommended in most cases.
They are designed to stabilize the lamp in the shortest possible
time with a minimum amount of sputtering (darkening). Ac¬
tually most lamps will stabilize after 100 hours of operation at
their design current, but since time is usually a factor, acceler¬
ated aging may be used.
If regulation as well as improved stabilization is required,
then higher aging currents for longer periods of time are
recommended. The sputtering can be disregarded since appear¬
ance and light output are usually not important in circuit com¬
ponent tj'pes. High-current aging also produces higher break¬
down and maintaining voltages, which may exclude it from
some applications.
No formula for aging has yet been worked out to include all
the variables, such as gas type, gas pressure, electrode mate¬
rial, etc., so the user as well as the manufacturer must some¬
times experiment to produce a desired result.
The electrode size and internal gas pressure will determine
the limits of the experimental aging current. High-pressure
gas and 12-mm electrodes indicate higher possible currents.
Some commercial types are aged at currents over 30 mA for
extended periods of time, but controlled conditions such as
forced air cooling are required.
The higher-pressure tubes are usually easy to identify as
they have a higher breakdown voltage, and the corona has a
tendency to concentrate in one spot. Low-pressure tubes, on
the other hand, produce low breakdown voltages and a “soft”
corona that covers the entire electrode.
In looking over the specification chart for T-2 neons, it can
be seen that precise maintaining voltages can be had for over
30,000 hours, but breakdowm voltages are more difficult to
stabilize, especially with pure neon (high brightness), so a
maximum figure is usually given. A guaranteed breakdown
voltage ±1 volt would have to include the ambient lighting
conditions to be valid. A tube of this type would almost ccr-

95
tainly be a low-pressure neon-argon mixture with a radioactive
additive.

AGING EQUIPMENT

It has been found experimentally that lamps aged on pulsat¬

ing dc exhibit superior qualities to those stabilized on pure or
filtered dc. One explanation that has been offered is that while
both methods use the same average current to stabilize the gas,
the pulsating dc has a higher peak current, which aids in the
cathode “cleaning up” process.
The circuit in Fig. 8-1 is a general-purpose device that will
satisfy most aging requirements. The 220 Vac is needed for

Fig. 8-1. Universal ac-dc aging circuit.

96
the higher breakdown types, and the variable autotransformer
may be used to adjust the peak dc current.
For lamps that are aged at currents greater than 4 mA, it
is recommended that at the end of the aging cycle the current
be reduced over a period of several minutes. This prevents a
rapid temperature change from making the glass brittle.
A period of 24 hours in the nonconducting state is then ad¬
vised before the aged lamps are tested to their electrical speci¬
fications. This is particularly important for breakdown volt¬
age tests which may produce as much as a 5-volt rise in 24
hours after accelerated aging.

NEON-LAMP SPECIFICATION CHART AND

NUMBERING SYSTEMS

The following chart represents nearly all of the neon lamps

available in the United States as stock items. Many other types
have been manufactured to meet individual customer needs and
are usually assigned a number that is preceded by the letter
“A.” This “Application” numbering system is necessary when
it is realized that any change in the manufacturing process
will indicate a change in the alpha-numeric designation. If,
for instance, an equipment manufacturer wants a SAG lamp
with guaranteed ionization time specifications, it will be as¬
signed an “A” number, even though it originally was a 5AG.
Sometimes these special lamps become popular enough to be
made available as stock items, as, for example, the A057B,
A016, etc.
The oldest and usually most familiar system of classifying
glow lamps is the “NE“ method and for this reason they are
listed in the left hand column.
The shortcomings of the "NE” system were noted by the
industry and as a result the American Standards Association
(ASA) offered a new system for lamp identification that in¬
cluded clearly defined standards. The ASA has been renamed
USAS (United States American Standard) and this designa¬
tion is the one recommended for current use. The system ap¬
plies only to neons that are primarily used as indicators. There
is no USAS numbering system for circuit component types.
General Electric identifies circuit component lamps with a
set of alpha-numeric characters that is similar to and com-

97
patible with the USAS method. The GE system always begins
with a number and is followed by two or three letters.
Tech-Neon and Signalite use an industrial system for high
volume types that is designed to minimize confusion by coding
the characteristics into the identification number. A T2-27-2T,
for instance, will indicate to the user that this is a T2 bulb,
27/32" long, filled with standard brightness gas, and has 2"
tinned wire leads.
A quick glance at the chart will show that in many cases the
difference between one lamp and another is slight, such as the
type of tip, length of bulb, length of lead, extinguishing volt-
test, etc. For many types, this simplifies replacement and sub¬
stitution problems.

USING THE SPECIFICATION CHART

The listings are divided into 3 groups: T2 miniature neon

lamps, T4% to Sl4 gas lamps, and T2 miniature voltage regu¬
lators. The T41/> to S14 group is included for reference, and,
with the exception of the NE51 types, their circuit component
use is limited.
The “T” in T2 describes the shape of the glass, tubular, and
the ‘,2’, refers to the approximate diameter in eighths of an
inch. For all new types, this represents a maximum diameter
of .250 in., but for some older types it is .275 in.
The first three columns provide a cross-reference and show
the lamp designation under any of the systems discussed. Thus
an A7A, T2-24-1, and NE2B are all the same lamp.
B’kdwn Volts is self-explanatory and footnotes are included
for special conditions.
Maint Volts figures are based on the listed design current.
Exting Volts shows the guaranteed extinguishing voltage
and indicates that each lamp is tested to this specification.
Des I mA lists the design current which is the basis of the
life and maintaining voltage figures. The design current is not
the maximum operating current.
Life Avg Hours figures for standard brightness indicators
are based on a 50-percent decrease in light output. The life of
high-brightness indicators is based on the point at which stan¬
dard line voltages (115 Vac) will fail to ionize the lamp. Cir¬
cuit component figures are explained by footnotes.

98
 Typ Rg Ohms is the value of resistance, ^20 percent, that
would usually be used in series with the indicator on a 115
Vac line.
Pre-Aged indicates whether or not the lamp has been fac¬
tory aged, and footnotes explain how the anode is identified.
Bulb Length Max In. is self-explanatory.
Base describes the method used to terminate the lamp.
Footnotes indicate special conditions and are listed at the
end of the chart.
The T4& to S14 chart is essentially the same as the T2 chart
and uses the same footnotes. There are a few additions.
Bulb Type is indicated by the same system as the T2. G is
globe-shaped and S is straight-sided. The numbers show7 the
maximum diameter in eighths of an inch.
MOL In. is the maximum overall length in inches, including
the base.

99
 —« —. — CO •
«n u: (O vd UD _ _ —• ID ^ in u']
. in lo ...

— ►— . <^ i/) wi ►—
o> a) <u a» qj : qj qj S 2 ? S-

1" Wire
n ? “

2" Wire
1" Wire
1" Wire
1" Wire
i= - - ~ i 5 « » qj s .i
s ? g ? ? r, 'z'z^.**
Sj«v — og — t/}^t'%!4t — — — I— l— — — I- _

IV,*
”/a*
2Vaa
*V8a
Va
CO C/S - C/1 t/S t/1

NO
-- NO
-- NO
— i NO

200K j NO
oooooocjoooooooooo

loooootsooooo 1 1 1 I O ' 1 < 1 I 1 1 ! 0 I

- -
i£Sr,Sn”22222 I I I I i i i i i i i i I rn I

wrv.fsKi'iN.rs.is.ivf»p«rca>(Vj('(iSiS!MtMa!«uieoui(M(v(v

12
12
2
2
30
OOOOOQOOOOtSOOOOOOOOCOOOOOOd

3.000
3.000
6.000
7.500
50
ooooc3CJOOOOOQOQOocjSoc:ooc>aaoo
q o o o o o q q o o q o o q q o o o o cs o o o o m a ®
us ui ift ui Ui i/i in* in ifl >/) i/> kft in id ri to iri <4 M O cvi <m‘ oi‘ in r-i
CU CM <\l MCMMMMNM-• CM CM

■nuOulOinooiN

.3
.3
3
.5
.5
1
-
-

-
-
50 Min.
60-80

48 58
60-80

-
'-50

o o o o 2epooc©oonso2
115 Ma*
65-80
65-80
120 150
110-140

cncnu^o-i^j^CTicJ'r^oooor-'O^
3AD
4AB
4AC

?AA
K4A

101
 to kO lO ip ifl (D COCSICVJ
. cm r>
« « CO U5 ic » CO (£ in « « CO « iD <\ CD CVJ
. . «"->
»? ■? t ’T ^ co co oc oo oc rg- oc oo

^ u" *■*“ > ,— o W W W Jf

u dj 1X1 a> a> jv a> "5 "2 oj ^ ^ oj aj 2 03 aa dj ^ oj __ _: _ ^ <d

a 2 s s ?i
I m oi “ “ > -- -:- >

cdoooooooooooooooooooo

^ ^ x: ± 3C
OCOr^^^OOOr^.r^-0 <vjr^. o O O O
CM in O; f <r N CM CM tj O Og O m un ro
T2 Miniature Neon Lamps

ooc300oooc:ooocdoocdc>oooocdoo
oooooooooooooooooooooooo
o o o o p o o o o o o o o o o o o o o o o o o o
in j> in in in i/i in' vn to ir> tn itj’ tr> tr> in" in in »n i/» i/> cn in »n
MfMfsjNfSffMCSjrsJCN»NCMNCM<SJMMCvJMCMNMMtNM

L*3 n f M CM CM n CO n CM CM

■ [. >:xxx xxx xxxxxxxxxx

, oaCTDCT>C^<\jr^TOf’3n3'^JCP<^3<^3rPf^rUCP
:oSSS55SSSSS5555£25
’> inoo^nvnu^ooo^>^CD<^cDcr)i/oi/^i
i (M^i^nfoncnaidi^comoiff>conM'

. . *7 , . —^ to trt . "
!<<c ctjc^cjogoc^^c accc*t<<<m<<<<<'muD<t<
— Pyj^CTlCMCMCMn-a-mcOCM— ---HfMm
:*: < <l <<<c<«!£<<r<<r<r><oooooooo2£a£a£a£a£

102
 o
J. <o (O ro ro
. U> 'X> r—1 m in in -S' CO lO UP <o CO CD* UP CD U3 «P CD CM
CM uS UP 40 tD id <-D co l© wo UP in LO u“> in in in in uS MO m in" m’ iT> O

co KT «5T rr ■** •*» <-b «X> U3 IO to CD CD *T -cj- ^a- ■u1 *7

e C C c
E
■O ■a -O -O ■o *0 Tj7 T> •o ■O T3 ip
c c c c c e c c Q> c
c a> o a» 4U ■S cx
i— 1“ i- U> o uj ►— h- •— •— 1— Zn +
a
a> 0> a> “
5 a: 5
jy
5
QJ QJ OJ jy QJ qj a> 0> (l> o » to Q> o> QJ <u «>
CSJ CVJ Cm CM 1—
* ? 5 i i i i ? i i ? a a a i a a i a a
or
tn - Kj «o - Cm « Ki K> N — ■it -
- - - - - - - - - - - K> - -

3, N r* „ w N w w c» c c * •x *x „ X -x „ „

J 4'
S' " S'
- « s' S' s' » w" « - * - - - - - «■ E" *■ S' *r s" ?T

m o CP (T» o —
£
CM CM CM ■3 CM CM CM

to </> CO (O CO CO cn C/7 C/7 CO co oo

o o © o o © o o o o o © o
•i >- >- >- >- >" >- >- >- >- >- >- >- >- Si

XL
fO (
1 i 1 i 1 i 1 i i ) l \ 1 i l i i i i 1 i 1 i l 1 i l

CM OJ fM CM CM <M Cm CM CM CM CM CM cm CM CM CM cm CM CM CM CM - r. CM CM CM CM -
- -

o o o rj o O o o O o o o O O cD O O o O O o o
CJ UJ UJ co c-> CD Q o O o C O
a
in" i© cd eg ia‘ cvj CM cvl CM CM CO CO tD «o ID id t£> CM CM uo
v" c>I MO
CM 1 Cm CM i

-r*- O' O' *3- n n n n n in in iTi r-*. |

cm in in
- -* ~ 2 ’ ’ l

i i i i
i i i i
c c d
5 2 Z 25 5 i i i i
CP <D O
i i i i
in in in
i i i i
■u- cn ro m CO ro to CO hs
■—1 - - •—• Cm CM r^j
cz> CD CO oo 03 rs*
lT5 CM Cm ur*> ts r-. ■•—•
A A UJ /• IO to CD CD to p- UJ
Ofl Ofl 1 CiC Wl od cii ob
CM o uS <T> cb
1 m U“> ■u. <L m U1 1/7 m m U“> U7 -a. -X

co co
^a-

x' CD »n in X w X
o
OU 30 D7 CO fM. O' m CD UJ co o> oi CP Oi o w CM cr> ©
s 5 s s
in CD CO o CD o in
fO CO co <o ID CD in CD <x> to UJ vD CD '*** to UT> in u> O) o>

<£ 03 C-> O Uj < CO CJ O llj u_ <f CD O Q

QQu.wuc C 5 300 i-,-;^mt»wai(nmiiiiixi-
CO co (V> co co ro co co co ro co co i/> u"> ici irt ul Ifl Lf> i/> lTi uo lO |C

103
 8. 46. 47
Notes

46. 53
46. 53

54. 46
8. 45

6. 46

52
52
52
52
52
53

46
46

46

58
8

6
6

6
6
6
6
- cn m
c 2J
Base

*” + 5
"j a a g QjtlJH<Ll<l)4jlUdl(U<)JtV4JDVUVQ7Q>Q7Q7^V
55S5^SSiS5SSJS5SSSi£i52Siii
Max. In.
Length

W?*J«H®T4N '*t«*e*?4Ne«55«C«D*J!,i?r«W <*< C* Ct f*

Bulb

4? 4? -5 4?

rv ““ ps Ps *—* *—* ^ 'ji ffi oi cn p*» p*v ps Ps ps ps

XO l-UJSfl — vn—• — — rr«r^T^^T — — — — — — —• \n — m^ninin
a „„„too^oot/:oot^)<yntOt^)t/50oc^oaoot/>tr>coto„£X)(/)t')t/><^>
O C_J C > Li » t_. J L.J Lxi LU 1 1 1 l>_| 1 ■ l 1 » f 1 ■ 1 1 J_l ^ L .1 1 II tn HI >11 tj ■ i 1 1 . i l l 1 L.l L. .
a'' ■*
lifl
zzz>->->->->->->->->->->->->->->->->->-a:>->->->->-

=■ - = 1 1 1 1 1 1 1 ! 1 1 1 1 1 1 1 1 1 1 1 1 J 1 1 1 1 1
JT“ ■= 1 1 1 1 I ■ l ■ 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
•” o
ZOt-WM <jiijii^cncnij'CDocrjiin\ni/ikOinininin i/i in i/> lt> i/i
T2 Minialuie Neon Lamps

rofor-jc-jcor^rn*/! iD U*1 iD in Ul
10,000
5,000
5,000
5.000
5.000
15.000
15,000
15,000
25,000

7,500
7,500
7,500
25,000
25,000

10,000
5,000
1,000
6,500
6.500

25,000
5,000
25,000
7.500

10,000
7,500
Hours
Avg.
Life

|iO»“UUfcO 50
U“>
Oes.

mA.

<-c <_o . krs /> iD iD lOuii/imrnrnrnm | r*i m c*i m

1

rs* cm, 50 o <-*> <—> cn3 csi en rri | cm

IO— cnocDoocDOOOoaiGic^CDCDcncn

ill i r t i i i i
iii ... i i i i i i i
OC l i iE = Ec = EEEeE‘=S£EESSi ..
1 5S5SSSSSSS5SSSS5S , , , , , ,
iS > , . cj o in in »tj o m lti in *r> o o o tr» c\j u*> o , , , , . , ,
t i 1 ininininminir\fiifiinin>ni/iiniDMM i 1 1 i 1 ' '
i r i "liiiili

£ zo— c ^ *?r
CM CM CM
cn
in
re
cc aii/iococnoooo — coor^-rooo , ° n u- id in
C3 C 42 intccoeocoinNKNr^iDifiiciflpsCJin 1 i ^ ui i/» in m
l *0 re o
re s >
. .. . % *T 1 | >
cm o i/i — ^CMOOOOinuscM—- ^ n im
mj>inicou>)iDiDU}U3inin/)(£)i£rH.(Ni
bO cm• cn• * m
| i < i/) ia in in
a
>
11 C3
° 20 — co co co oo oo cO co co co cn co
^ ^7 in
C
2 2 2o->cDOocD<yooooccunvocoouDOOO S m m m m
£ */l ^^12M^M’7^NC\J^lDa^rsKN(CVOlf!COini5psrNfsN
o •—• ■—• ■—« cm
° ^ ^ ^ rvj — — — — cm2;
"5
^ > inminu56inin»nii)OinoocM»iflf;>6«t«j^^inu1iihinin
CO cocococPr^-tDOa^aaQ—CO IO Ifl ifi ID

o 10
o o
ltj r^.
— — 2 OZ QZ cc Qi
^ ^ “ a: £ 3: 5 i
^ < lO CO CO lO CM fNJ CO lO

I 5 ; CVJ N N
«Nv
fy >— ►—
H h
CM tv (SI CM (SI K
r)J *- 1- t- k— I- tO
Niococococoa-*tf)
cd CD cr> < *
ID iD l/l ID
7
OO^OOO o o o o
—i —I -J K K □£ C£ C^HHK^h-OOiO <7> — <*<*«!E<tC<£<t

104
IDLOCOlDlfliXJlOlDrJ 0 uJ CD ID O) ID C ID (C

O O O <U Hj jya>o>a>A>ooo«5ya>

J J J 5J J J X X J55 j 5 5

I v* '-o
1 rt vT

^> cn
U*5 U“) U"> U">

Wyicooocoviww c^ cO co to co

i i 2
NMfs,PH<J)CMP*-rx

OOOOOOOOOCJOOOOOOOO
oooooooooooooooooo
iniiommoomooooooooooir)
hvNfvrsOQSLniDi^ c> O CD <T> O O r^-T
—' ^ fM C^fNJ CNI C*J CM

fO rO «-0 r^)

QO OQ fN CO
T*- rr *r»

f*** UJ CiJ 00 C\f I***

s:. c^j in 6 ,

m m in in « k y-J £0 x x vx; x
J2J2CjSj^J?SWjp.

— _ O0 _ _ „

{Si CSI
<£ Z

105
 « *•» s os
5^ S' S' S'£ 55" «**
- -

cccS"J!; = ;SJMSIS«;5£cC iSSliiil?

' to ™ £ ^ ^ £ £ ™
2. 2 2 *J t-> O OH 2 o ooovtj o -j. to t/j ° £> 2.
5*
Bal®TiTiTi?co'0-oti®Ti-a'ofl3?cH“a“
O CJ O “
a o c/3 5
.2
5
£?
Scjt=>3E2Ec3££ 5
TO TO O O O
o o o <✓> O

.srsisisiNr~P'''rs(NfM

ogooowoocjooooooociooo
oSoooooooooocpooooooo
o ooooooooooo o o u-> o o o «n
o" o’ o’ o" (*>" o O d o o o o d r^' m' < m’ ~ ui i^'

E C\j —• CM f^CMCMC--i<vio«)ooooccioooo<^^»tMrr
— —■ —. —i ^ • —i n n n id

I I I I I I
I I I I I I
I I I I I I

I \ I I I
I I I I I
I 1 I I I

to to to “ to to ra ®n«i»inm«i“n “i1 u ™ to
EEeSEEEEEEEEEEtoESSeeE

5 a

*~~ Kh-Hh-Kt/>^WOOWV)W5W(OWWV>h.HH-hKKHhh

< < < <

cn — m —
CO u. CO CO

a: <t q: < cn
ooo-«o;^'J'Jiooc>oni/> ^
romfOcorororororo-^^j-^

106
 1f) cr>
N N N S
1X>

*_ * » ! I | *_ « « i
Cf » * 1 I * n m «>
^ C ^ S' o~ C C i I S' ft- - -
— — ft- ft- 1 1 — - S' Sr

i 5 "S ? o.'
SSci^SCusiSOcj.
>,>>>, >,
1^ ft fl) rts «"0 u o go ^ cn g.'S^ o S' g. cn
(~p ff*< Pf*1 I

S 2 S 5 £ -

ooooooooooooinaoopoooooooooo
e}OOOOooooooocNJooo<Soommoooooo
e> o o o o m o o o in o in o o o o o_ o — —• © © © o a ©
o" O o’ o’ o’ O rs in" n.' —’ o’ O o’ --' —’ m’ n" — •-' m" iri

m *m m 1
r~- © r->- |
in in in i
*o l/> t£> I

^ ^ ^ > > > > O O 'T ^ > I — > :> ;>

po po po n *5T ■ *»r , —• 0-> ^s* ^3-

I
 I! I ” -s — O = O ™
oc
£ c
Z. lA ~ e 3 « r “ 3
^ -S t)~ «<5 o Q. pj « 2 TS
, i2 JS -
5*1 ” I? 2 - |E J2
— r»
a.y l-c “ .c *; J= 5 « 2? § 2? m ho
= IS ‘- s= 1- * S — o —
JZ “-
a» £
~ Q- S °

a> _ pouuuuupuuuuupouuouuucjuu
>>>>>>>>>>>>>>>>>>>>>>>>
EEEEEEEEEEEEEEEEEEEEEEEE
l/% krt lt> lT> utj ut>
NMfNjNNfnnnno''j^:oiff>ai^in»ooookntr)in
T2 Voltage Regulators

<<<<<<<<<<<<<<<<<<<<<<<<
EE£EEEEE££EEE£EE£EEEEEEE
oooLnooj-«irii«oQooiriirJOoQkOicoo»r)tf>»r>oo

„„r__„_„„„_„__f0r0f0pvrv]CVJ
♦ +! >1 ♦! +1 +1 H +1 tI +1 *t +| +! +1 +i +1 +! +! ±| +1 +l + +i *i
"• ^ n ^ o© oo o*>

“2 JJ- —o Ok^«oocooo»^oooo«nootntf)omoininin
* r>j r? m m m rn (Q t£ t^u’Jin^focOf'j — -«cnj

(M <NI M
<i> ^ il>

u->

a cc o m i/)
Kccccttcxaaa:^^^
o-ioin^moifoaircr
— o o a o—— —< oo ^ o-> —•
■ * **—' ■ * ■ * M oo oo ji
N N N N N N N N N N N N N NNrsJNNNNN>>>

108
 V103R2 135 103±2 .8 mA. <2 volts from .2 - 2.0 mA. <15 mV/’C 'These types have a
V110R4 170 1102:2 1.5 mA <2 volts from .5 • 4.0 mA <15 mV/'C metal jacket and
V115R4 155 11512 ,8 mA <2 volts from .15- 4.0 mA <15 mV/’C slightly different
V116R2 150 116±2 6 mA. <2 volts from .12- 2 0 mA <15 mV/'C characteristics
V139R1.9 190 139±4 5 mA. <2 volts from .3 - 1.9 mA. <15 mV/°C

o
■»->
a>
Z,
*
M

—
"
C

E
c

a.
N OO O' O
c:
u M

;i I
V T3 V OJ «
e
■o _ T3 is -o

TJ n B D -D
>%>*».-

i_ o
;^E.E
ns
o

_ 'ra "S
c ^
o
™
«i
O
<( m <t <t < j u.

g-

c
. .

o u is x a
° <u XX

-O *o
a
S' _"3

2
ti

nj g
f=(
N m ^ in ID rs
— — - MNNMfMNNM

«MfO»inifllsM[TiO —
a

12 End of life is 10-volt change in breakdown or maintaining voltage. 28 Maximum breakdown in total darkness is 100 Vac.
13 After 100 hours at design current. 29 MOL 1.030’.
14 Anode identified by blue dot. 30 Based on 50% decrease in ultraviolet output.
15 Maximum diameter is .275“. 31 Based on use as a film marker.

109
16 100-volt maximum in total darkness. 32 Argon filled.
 £ e
Based on 6-volt change in Breakdown or maintaining voltage.

* 2 2
_ *- *- aj
o m _o
-o “ «, S <U _5
u ^ Q
c ■=> o S
™ u o »r
r: in ns •*
£ > >■ =
«| o o 5f
*- «m m 2:
— (M
«£ o o _

o ”■ — o o —
10 ^
^“"0*0
"Z d> a> — T3
O “O "O
oj be aj = U O
w « Z OJ
Emits blue-white light.

5 E c c - C
CD —
a> .O g DO (A
o> — - S’ °
^ T) - o l- I- Aj
2 o *o u u
; 5 S S | Tf Q
~ ** **
? Q Jj 2 aj Jj
S £ ~ s.
“ -D g U
ro +> OJ 2E ■= •= 5 * 41 O at .o
<* « = £• — QD CW> T3 wJ C C £ ^ T) T3
.
(O ro <u
E 1 '“ ■§ e s S5'&si OJ ft* “5
c
cs c a> — — * 5 ^ = ex -2
U3 < Q X O O O 3 03
54
55

O'-»f'jrr)l«JI/lli3NC0C»'O-'

- 5 *
5 o o

45 £ <x
§ -2 -
" K
ro -r
*“• ^ 4)
Minimum design current is 1.5 mA.

fe
E

aj ^ S
^ ™ •* -B o = «
»T3 ^
P ^ El?
Helium-argon filled.

<U *1 O
■& .= ~ E
S ^ ■gy ■o ro — a>
£ £ 5 £ «s'i £ c m u-) —
7 * T5 £
c - bq u-i Si *
o *# m r-- e § -S i E * § 5 * i -B « ? i
T3 ^ “ 1 e a; m
•J _J
a. i E
a> o Si — -a
«s O O o _ _. .. o « -o re
a. £ a *'»oc;a>a>e.2?-c>
oo X 3 I <t o- o 3k£hk<ui<
33
34

110
 TESTING GUIDELINES
A preliminary visual inspection under operating conditions
can sometimes reveal useful information such as the type of
gas, length of electrodes, and whether or not it is a high pres¬
sure type (small corona and widely-spaced electrodes).
It can also reveal defective conditions such as excessive
sputtering, misaligned electrodes, arcing, and leaks. Normal
indicator types, all of which use lower pressures, may be con¬
sidered defective if the corona “jumps,” or if it fails to cover
% of the electrode. It may be worthwhile to note that even if
an indicator electrode is completely covered but the corona
is “soft” or “flowery,” it is usually considered defective, be¬
cause the life figures for these types are greatly reduced.
Electrical tests are, of course, performed by whatever in¬
struments are available. Oscilloscopes, digital voltmeters, or
electrometers can all be used to perform the same test and get
nearly the same results, so rather than include detailed test
procedures, a few overall guidelines are listed.

1. Try to test the lamp in the actual circuit.

2. Test instruments having a high input impedance are
recommended. The 1-megohm oscilloscopes are satisfac¬
tory for static breakdown and maintaining voltage tests,
but can disable an oscillator or other high-resistance cir¬
cuit.
3. Breakdown voltages are affected by radiation fields, am¬
bient light, the length of time it has been in the conduct¬
ing state, and the speed with which the breakdown volt¬
age is applied (ramp slope or rise time). The test condi¬
tions must be specified to make the test valid.
4. Specify the circuit resistance used in any extinguishing
voltage test.
5. Shunt capacitance as small as 1 pF (scope probe), can
cause parasitic oscillations when observing the high-re¬
sistance side of the lamp (over 1 megohm).
6. The dynamic differentia] voltage or peak-to-peak wave¬
form of an oscillator is not the same as the dc differen¬
tial voltage, so each should be tested in a different man¬
ner.
7. Ionization time tests should include risetime, or ramp

111
 characteristics, plus the amplitude of the ionizing pulse.
8. High-pressure types are usually tested with, or monitored
by, an oscilloscope, as the inherent noise spikes and volt¬
age jumps cannot be easily recognized by voltmeters or
counters.

When a quantity of neon lamps is to be tested, clip leads

and soldered connections may, at times, be considered too slow.
One solution is to use a transistor test socket such as the Po¬
mona TS-187. Another solution is to make a test stand of plas¬
tic or bakelite and drill two vertical holes Vb inch in diameter
and 2 inches deep. Fill the holes with mercury and contact the
base of the mercury column with horizontal external screws.
These screws are used for the electrical connections, and the
mercury pools serve as the test socket. Still another method is
to use two small magnets separated by a piece of plastic and se¬
cured to a board. The magnets not only serve as the electrical
connection but they will hold the Dumet lamp leads.

SPECIFYING GUIDELINES

It is usually not necessary to use any one designation when

ordering glow lamps from the manufacturer as he will fur¬
nish the correct component under its proper listing. If, how¬
ever, the lamp is ordered from an electronic parts or whole¬
sale house, the designation as listed in its catalog should be
used.
Actually, specifications alone are all that are needed by most
manufacturers, even for orders as small as 100 lamps. The
user has only to keep in mind the basic limitations of the neon
tube, such as the voltage and current capabilities. Maintain¬
ing voltages less than 45 volts and breakdown voltages in ex¬
cess of 250 volts, for instance, are unrealistic, even though
they are possible.
Perhaps the main reason that ordering by specification has
become popular is that the users can include special tests that
are of particular importance. Some common “specials” are
wire leads several feet long, energy transfer test, lamp par¬
tially painted with reflective material, silver plated leads,
guaranteed sawtooth amplitude at a particular frequency, and
a guaranteed frequency of oscillation.

112
 PRICING GUIDELINES
Each specification requested will add to the price of the lamp
and if the specification is made tighter, the purchase price will
be even higher.
Any additional steps in the manufacturing procedure will
also increase costs. This includes welding, tinning, acid frost¬
ing, gauging, aging, encapsulating, and electrical testing.
The net price for an average regulator is around $1.60, while
circuit components range from $ .10 to $ .45. The average
net cost of a T2 indicator type (unbased) is about $ .08.

MOUNTING CONSIDERATIONS
Tip shapes and base terminals have some bearing on mount¬
ing methods used for neon lamps. Length of service and need
for replacement are also factors to consider; that is, should it
be a clamp or socket, for easy replacement, or can the lamp
be cemented in a more permanent installation? Fig. 8-2 shows

RANDOM FORMED ROUND FLAT

OR DRAWN

#1
TELEPHONE SLIDE

Fig. 8-?. Neon-lamp tips and bases.

113
tip shapes and basing construction of some miniature neon
lamps. Fig. 8-3 shows several methods of mounting to a printed
circuit board. Multiple mounting and panel mounting exam¬
ples are shown in Fig. 8-4. One commercial neon lamp holder
(Fig. 8-5) is designed to mount in a slot in a panel and includes
a colored indicator lens.

SILICONE RUBBER BLACK EPOXY NYLON CLAMP METAL CLAMP

SILASTIC RTV 732 ECCOBOND 45 WALDON CCN33 NEWARK 3GF359

Fig. 6-3. Printed circuit board mountings.

T1 AND BALL-END LAMPS

Lamps Inc. manufactures three neon lamps with diameters

of .125 in. All are the high-brightness type, pre-aged, and com¬
pensated for dark-effect.
USAS Type AIK is .250 in. long with 1 in. gold-plated leads.
USAS Type AIL has a sub-midget flange base with a MOL
of .360 in.
Manufacturer’s type 95BE is a special lamp that has a ball¬
shaped viewing end on the .125-in. shaft. This permits the
lamp to be mounted directly in a panel hole and secured in the
rear with an O-ring. This type of mounting is shown in Fig.
8-6. Mounting with a rubber grommet is also shown in the
same figure. The 95BE has an MOL of .500 in. and comes with
1-in. gold-plated leads.

114
ALUMINUM BAR FOR SHIELDING EPOXY CEMENT

SILASTIC RTV732

1/8" BAKELITE 1/4" HOLES

115
 Fig. 8-6. Ball-end lamp mounting.

Tl% CRATER-ELECTRODE LAMPS

Alco Electronic Parts, Inc. offers two unbased lamps having

0.172 in. diameters and round tips. The crater or “bullseye”
electrode is used in these types to increase the light output
from the viewing end.
Manufacturer’s Type MNE-4L comes with 10-inch insulated
leads and type MNE-4 has short, untinned leads.

116
 Appendix

USING THE NOMOGRAMS

The frequency nomograms in Figs. A-l, A-2, and A-3 show

the relationship between the RC time constant, power supply
voltages, and frequency.
If a straight line is connected between any two known val¬
ues, the third or unknown value can be found along the same
line.
Example: A one-lamp oscillator using a 10-meg resistor
and a .001-/J.F capacitor is connected to a 175-
volt power supply.
The frequency can be determined by extend¬
ing a straight line on Fig. A-2 from 175 volts
through time constant .01 (10,000,000 ohms x
.000000001 farad), to the Hz scale.
(An RC time-constant nomogram is also in¬
cluded in this section for convenience.)
Answer: 600 Hz.

When the oscillator nomograms are used to find the needed

time constant, then the chapter on oscillators should also be
consulted, since there are minimum and maximum resistance
values associated with each oscillator type.
The time constant for the astable multivibrator is calculated
by multiplying the value of C in farads by the SUM of R1 and
R2 in ohms. Equal values of resistance provide a symmetrical
output.
The fourth nomogram (Fig. A-4), is an RC time-constant
nomogram that is limited to the range and parts values nor¬
mally encountered in gas tube oscillators.
Again, a straight line connected between any two known
values will reveal the third or unknown quantity along the
same line.

117
 Fig. A-I. Low-frequency oscillator nomograph.

118
119
 / Egpp •* Ebkdwn ' ^maint
(R1+R2I C log.
Rl< R2« 6' Eapp " Ebkdwn
T C -

V 1(0 V2(

(Rl*-R2)xC
TIME
CONSTANT

SUPPLY
VOLTS

VI AND V2 ARE STANDARD-BRIGHTNESS LAMPS

WITH AVERAGE CHARACTERISTICS
AFTER 100 HOURS OPERATION

Fig. A-3. Asfable-multivibrator frequency nomograph.

120
121
 Index

A Brightness
high, 16,17
Abnormal glow, 10 standard, 16,17
Ac calibrator, 87 Burn-out, 15
Aging
procedures, 94-96 C
process, 11
Algebraic addition of voltages, Cadmium selenide, 66
33, 34 Cadmium sulfide, 66
Alignment, radio, 91 Calibrator
Altitude, effect of, 16 ac, 87
Amplifier, sine-wave, 70 digital, 86
A-m signal generator, 90, 91 voltage, 83-88
and gate, 51-53 Capacitance of glow lamp, 93
Antileakage coating, 94 Capacitive starting, 30, 33
Arc suppression, 76 Cascaded reference, 31
Argon, 12 Cathode
Arrester, lightning, 76, 77 cold, 7
Astable multivibrator, 43, 45, 68, 69 sputtering, 26
Audio Characteristic curve,
output indicator, 24 of neon lamp, 9
switch, 74, 75 Coating
Avalanche antileakage, 94
current, 8, 10 of electrodes, 13
time, 41 Cog-wheel effect, 62
Cold cathode, 7
Color of lamps, 16
B
Compensation for dark effect, 12
Ball-end lamps, 114 Construction of lamps, 17
Barium, 13 Control
Binary counter, 51 SCR, 62
Bistable multivibrator, 49, 50, 74 touch, 74
Breakdown voltage, 8,10 Corona, 10
static, 10 jump, 42

123
Corona—cont’d Flasher
mode, 9 neon, 43, 46, 47
unstable, 13 random, 48
Corotron, 9 sequential, 47, 48
Counter Flip-flop multivibrator, 49, 50
binary, 51 Foreign lamps, 17, 18
ring, 54, 55 Frequency
Crater electrode, 116 doubling, with multivibrator, 46
Current limit of oscillator, 37, 42
avalanche, 8,10 of light radiated hy gas lamps, 93
design, 11 of multivibrator, 44
run-away, 8 Fuse indicators, 22, 23
self-sustaining, 8

G
D
Gamma radiation, 13
Dark effect, 11 Gas
compensation, 12 lamp resistance, 7, 93, 94
Darkening, 16 pressure, 13, 42
Decade ring counter, 56, 58 tubes, series operation of, 29
Deionization time, 10,11, 55, 56 Gate
effect on oscillator frequency, 42 AND, 51-53
Delay MAJORITY, 52, 53
pulse, 75 OR, 51, 52
time, 53 Generator
Design a-m signal, 90, 91
current, 11 high-amplitude sawtooth, 42
of regulator, 33 square-wave, 45
Differential voltage, 10, 54 Glow
reference, 32 abnormal, 10
Digital calibrator, 86 normal, 10
Diode isolation, 29

H
E
Helium, 12, 16
Efficiency of lamps, 15 High
Electrode brightness, 16, 17
coating, 13 current regulator, 26, 31, 32
crater, 116 energy detection, 90
materials, 12 pressure gas, 42
size, 13, 26 Holding voltage, 10
spacing, 13 Humidity sensor, 71
End-of-life, 11
Extinguishing voltage, 10
I
F Incandescent lamp, 15
Firing miniature, 15
potential, 10 Indicating lamps, 18-24
resistor, 28 Indication, short-pulse, 21, 22

124
Indicator Mounting neon lamps, 113,114
audio output, 24 Multivibrator
fuse, 22, 23 astable, 43, 45, 68, 69
nonlatching, 20 bistable, 49, 50, 74
Ion, 9 flip-flop, 49, 50
Ionization, 7-9 frequency of, 44
causes of, 10, 13 monostable, 50, 51
time, 10, 41 two-lamp, 43
Isolation, by diode, 29
N
J
Negative
Junction devices, resistance, 11
photoconductive, 71 temperature coefficient, 13
Neon
flasher, 43, 46, 47
K
glow, color of, 12
Krypton, 12 Neon lamp, 15
Krypton 85, 12 characteristic curve, 9
defined,7
other names, 7
L
specification chart, 100-110
Lamp Neon lamps
colors, 16 hall-end, 114
construction, 17 mounting, 113,114
efficiencies, 15 testing, 111
incandescent, 15 Neon-operated relay, 62, 63
neon,15 Neon-regulated supply, 80
defined,15 Nickel, 12
Lamps, indicating, 18-24 Nonlatching indicator, 20
Lamp, tungsten, 15, 16 Normal glow, 10
Life of lamps, 17 Numbering systems, 97
Light, frequency radiated by gas
lamps, 93 O
Lightning arrester, 76, 77
Light-operated threshold circuit, 69 or gate, 51, 52
Limiting resistor, 18 Oscillation, relaxation, 19, 38
Oscillations, parasitic, 44, 54
Oscillator
M
frequency limit, 37
Maintaining voltage, 8 sawtooth, 38, 39
majority gate, 52, 53 single lamp, 37
Manley-Buckley ring counter, synchronized, 40, 41
54, 55 triggering, 39
Memory circuit, 65, 66 Overvoltage protection, 76-78
Mercury vapor, 16
Miniature incandescent lamp, 15 P
Molybdenum, 12
Monostable multivibrator, 50, 51 Parallel starting, 29

125
Parasitic oscillations, 44, 54 Resistance
Photocell, 66, 67 negative, 11
Photochopper, 68, 69 of gas lamps, 7, 93, 94
Photoconductive junction series, calculation of, 27, 31, 36
devices, 71 Resistor
Polarization, 12 firing, 28
Power line tester, 89 limiting, 18
Power supply voltage-controlled, 68
neon regulated, 80 Rf radiation, 13
regulated, 79-83 Ring counter
unregulated, 79, 80 decade, 56, 58
Pressure of gas, 13 Manley-Buckley, 54, 55
Pulse Run-away current, 8
delay, variable, 75
trigger, 39
S

R Sawtooth
generator, high-amplitude, 42
Radiation, 13 oscillator, 38, 39
gamma, 13 SCR, 61
rf, 13 control, 62
Radio alignment, 91 Screen-grid regulator, 34
Random flasher, 48 Self-sustaining current, 8
Rectifiers, silicon controlled, 61 Sensor
Reference humidity, 77
cascaded, 31 temperature, 71
circuit, voltage, 27 Sequential flasher, 47, 48
regulated, series-pass, 34, 35 Series
Regulated operation of gas tubes, 29
power supplies, 79-83 regulation, 81
reference, series-pass, 34, 35 resistance, calculation of,
Regulation 27, 31, 36
curve, 84 starting, 29
series, 81 Series-pass regulated reference,
Regulator 34,35
design, 33 Short-pulse indication, 21, 22
high-current, 26, 31, 32 Shunt
input voltage, 28 regulation, 81, 83
load voltage, 28 starting, 29, 30
screen-grid, 34 Silicon controlled rectifiers
vacuum-tube, 79, 80 (see SCR)
voltage, general purpose, 28 Sine-wave
Relaxation oscillation, 19, 38 amplifier, 70
Relay oscillator, 41
memory, 65, 66 Single lamp oscillator, 37
neon-lamp operation of, 62, 63 Spacing of electrodes, 13
threshold, 63, 64 Specification chart, neon lamps,
transistor driven, 64 100-110

126
Sputtering, 11 Two-lamp multivibrator, 43
cathode, 26
Square-wave generator, 45
U
Stabilization of gas lamps, 95
Standard brightness, 16, 17 Ultraviolet light, 12,17
Standing rise, 11 Unregulated power supply, 79, 80
Starting Unstable corona, 13
capacitive, 80, 33
parallel, 29 V
series, 29
shunt, 29, 30 Vacuum-tube regulators, 79, 80
Static breakdown voltage, 10 Voltage
Striking voltage, 10 algebraic addition of, 33, 34
Strontium, 13 breakdown, 8, 10
Switch, audio, 74, 75 calibrators, 83-88
Synchronized oscillator, 40, 41 differential, 10, 54
extinguishing, 10
holding, 10
T
jump, 17, 42
Temperature maintaining, 8
effect of, 13 reference circuit, 27
sensor, 71 reference, differential, 32
Tester, power line, 89 regulator
Tests for neon lamps, 111 general purpose, 28
Threshold input, 28
circuit, light-operated, 69 load, 28
relay, 63, 64 striking, 10
Thyristor, 61 Voltage-controlled resistor, 68
Timer circuits, 71-73 Voltmeter, transient, 88, 89
Touch control, 74
Townsend discharge, 10
W
Transient voltmeter, 88, 89
Transistor driven relay, 64 Work function, 12
Trigger
circuit, 39, 56, 57
X
pulse, 39
Tungsten lamp, 15,16 Xenon, 12

127
 USING and UNDERSTANDING
MINIATURE NEON LAMPS
by William G. Miller

Practically everyone, at some time or other, has used, or has seen

in use, a neon tester, that simple gadget which gives out a cheerful
orange glow when plugged into a live wall receptacle. This instrument
will be found in almost every electrician's kit. Another person who
has been exposed to this device is the hi-fi enthusiast, who uses it as
a strobe light to check the speed of his record player.
These comparatively simple uses of the neon lamp may lead some
persons to discount its importance as an electronic component. If
that has been your attitude, this book will do much to dispel it and will
show that the miniature neon lamp is potentially a very versatile device,
capable of controlling some rather sophisticated circuitry.
The various aspects of neon lamp construction, such as electrode
size, gases used, firing, maintenance, and extinction voltages, and
aging characteristics, are covered first in this book. Chapters are
devoted to its use as an indicator, and for voltage regulation and
reference voltages. The use of the neon lamp as an oscillator, pulse
generator, flasher, and in computer applications is then given. Chapter
6 contains a number of fascinating miscellaneous circuits that can
easily be built by the home experimenter. Power supplies and instru¬
ments that can be used to power some of the circuits are shown in
Chapter 7, while the final chapter lists the characteristics of most
available neon lamps.

ABOUT THE AUTHOR

William G. Miller is currently an applications and develop¬
ment engineer for the Tech-Neon Division ot Industrial
Electronics, where he is concerned mainly with circuit
and product design. He has worked as a design engineer
and fulfilled assignments in the Aerospace and Oceanog¬
raphy fields. During his military service he was an army
microwave-systems instructor.
He has written several articles tor electronics magazines,
plus editing Tech-Neon’s own "Applications Newsletter."

Q I HDWARD W. SAMS & CD., INC.

I THE BDBBS-MERRILL CD., INC.

20698
$2.95 (In Canada 53.75)