Scribd
Upload
47 views

Automatic Load Controller

This document describes an automatic room light controller circuit that uses an infrared sensor to count the number of people entering and leaving a room. It controls the room lights and displays the number of occupants on a 7-segment display. The circuit uses an AT89S52 microcontroller to receive signals from the infrared sensors and control the lights and display accordingly. When someone enters the room, the counter increases by one and the lights turn on. When a person leaves, the counter decreases by one, and the lights will remain on until the room is empty.

Uploaded by

Sreenivas Ganapathi
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
47 views

Automatic Load Controller

This document describes an automatic room light controller circuit that uses an infrared sensor to count the number of people entering and leaving a room. It controls the room lights and displays the number of occupants on a 7-segment display. The circuit uses an AT89S52 microcontroller to receive signals from the infrared sensors and control the lights and display accordingly. When someone enters the room, the counter increases by one and the lights turn on. When a person leaves, the counter decreases by one, and the lights will remain on until the room is empty.

Uploaded by

Sreenivas Ganapathi
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

Automatic Room Light Controller

AIM: To controlling the room lights as well as counting number of persons in the room

LIST OF COMPONENTS:

 Microcontroller – AT89S52
 IC – LM555
 Transistor –BC548,2N2222
 Diode-IN4148
 Sensor – TSOP 1738 (Infrared Sensor)
 Transformer – 12-0-12, 500 mA
 Preset – 4.7K
 Disc capacitor – 104,33pF
 Reset button switch
 7 Segment display

CIRCUIT DIAGRAM:

Transmitter :
Receiver:

OPERATION:

This Project Automatic Room Light Controller with Visitor Counter using Microcontroller is a reliable
circuit that takes over the task of controlling the room lights as well us counting number of persons/
visitors in the room very accurately. When somebody enters into the room then the counter is
incremented by one and the light in the room will be switched ON and when any one leaves the room
then the counter is decremented by one. The light will be only switched OFF until all the persons in the
room go out. The total number of persons inside the room is also displayed on the seven segment
displays.
The microcontroller does the above job. It receives the signals from the sensors, and this signal is
operated under the control of software which is stored in ROM. Microcontroller AT89S52 continuously
monitor the Infrared Receivers, When any object pass through the IR Receiver's then the IR Rays falling
on the receiver's are obstructed , this obstruction is sensed by the Microcontroller

DESCRIPTION OF THE COMPONENTS USED


1. Microcontroller AT89S52:

The AT89S52 is a low-power, high-performance CMOS 8-bitmicrocontroller with 8K bytes of


in-system programmable Flash memory. The device is manufactured using Atmel’s high-density
nonvolatile memory technology and is compatible with the Industry-standard 80C51 instruction
set and pin out. The on-chip Flash allows the program memory to be reprogrammed in-system
or by a conventional nonvolatile memory pro -grammar. By combining a versatile 8-
bit CPU with in-system programmable Flash on a monolithic chip, the Atmel AT89S52 is a
powerful microcontroller which pr ovides a highly-flexible and cost-effective solution
to many embedded control applications

Infrared sensor:

The TSOP17.. – Series are miniaturized receivers for infrared remote control s y s t e m s . P I N d i o d e
a n d p r e a m p l i f i e r a r e a s s e m b l e d o n l e a d f r a m e , t h e e p o x y package is designed as IR
filter. The demodulated output signal can directly be decoded by a microprocessor. TSOP17.. is the
standard IR remote control receiver series, supporting all major transmission codes

LM555 TIMER

The LM555 is a highly stable device for generating accurate time delays or oscillation. Additional
terminals are provided for triggering or resetting if desired. In the time delay mode of operation, the time
is precisely controlled by one external resistor and capacitor. For a stable operation as an oscillator, the
free running frequency and duty cycle are accurately controlled with two external resistors and one
capacitor. The circuit may be triggered and reset on falling waveforms, and the output circuit can source
or sink up to 200mA or drive TTL

4) LTS 542 (7-Segment Display)

The LTS 542 is a 0.52 inch digit height single digit seven-segment display.This device utilizes Hi -
eff. Red LED chips, which are made from GaAsP on GaP substrate, and has a red face and red
segment.

RELAY:

A single pole dabble throw (SPDT) relay is connected to port RB1 of the microcontroller
through a driver transistor. The relay requires 12 volts at a currentof around 100ma, which cannot be
provided by the microcontroller. So the driver transistor is added. The relay is used to operate the external
solenoid forming part of a locking device or for operating any other electrical devices. Normally the relay
remains off. As soon as pin of the microcontroller goes high, the relay operates and releases. Diode D2
is the standard diode on a mechanical relay to prevent back EMF from damaging Q3 when the
relay releases.
APPLICATIONS:

1. Can be used in various rooms like seminar hall, where the capacity of room is limited and
should not be exceeded. Project will display the actual number of persons inside the room.
2. Can be used in conference room, study rooms in colleges.

Future Development:

1. We can send this data to a remote location using mobile or internet


2. Voice alarm system can be added to indicate that room is full & persons can’t enter inside.

You might also like