XK3190-D18M2

Weighing Indicator

User Manual
April of 2008 Version

Shanghai Yaohua Weighing System Co., Ltd

 XK3190－D18 Technical Parameters

Chapter 1 Technical Parameters

1. Model: XK3190-D18 Weighing Indicator

2. Accuracy: Grade III, n=5000

3. Analog part:

AD conversion method: Σ-Δ conversion

Maximum conversion code: 24 bits

Conversion speed: 50 times/second ~ 200 times/second

Input signal range: -20 ~ 20mV

Non-linearity: ≤0.0015%FS

Zero temperature shift: ≤0.05uV/℃

Load cell Excitation: AC 5V, 250mA, available to connect with 12 load cells of 350Ω or 24

load cells of 700Ω

Maximum sensitivity: 0.5uV/d

Connecting method of load cell: 6-wire method, and automatic compensation for long wire

4. Display

D18M1 Indicator with single window FSTN 240×64 Dot matrix LCD with high contrast

D18M2 Indicator with double windows 6-bit LED + 128×96 Dot matrix LCD

5. Keyboard

Number keys: 0~9

Function keys: 23 (among which 10 are overlapped with number keys)

6. Clock: available to indicate year, month, date, hour, minute and second as well

as automatic leap year and leap month

Precision: ±5s/24h, not affected by power-off.

7. Scoreboard display interface

Transmission method: serial output method, 20mA current loop signal (with constant current

source output)

(RS232 interface optional)

Transmission style: 11-bit binary number

Transmission baud rate: 600

１
 XK3190－D18 Technical Parameters
Transmission distance: ≤2000m

8. Serial communication interface

Transmission method: RS232, RS422/RS485 (optional)

Baud rate: 600/1200/2400/4800/9600 optional

Data transmission style: 10-bit binary number, 1 start bit, 8 data bits (ASCII code) and 1 stop bit

Transmission distance: RS232 ≤15m RS422/RS485 ≤1000m

9. Printing interface

1) Panel-type microprinter

Printing paper: thermal paper with width of 57mm and roll external diameter less than 40mm

2) Standard parallel printing interface: available to connect with line printers such as ESPON LQ-300K,

KX-P1131 and KX-P1121 etc.

10. Data memory

Available to store 1000 sets of vehicle number, tare weight, 1000 sets of cargo names, 1000 sets of

weighing records and 50 sets of Overload RECs

11. Use Environment

Power supply: AC 110V~220V, 50~60Hz, Current: ≤0.3A

DC 6V-8V (optional), Current: ≤0.6A when not printing while ≤3A for printing

Use temperature: 0℃~ 40℃

Storage temperature: -25℃ ~ +55℃

Relative humidity: ≤85%RH

Preheating time: 10～30min

12. Indicator features

●32-bit ARM processor with high speed and high performance, and built-in operating system are adopted to

make real-time and correct accumulation, calculation, memory, inquiry and printing of the weight data;

●Humanized operating interface, two-dimensional rolling menu bar management, quick positioning of required

parameters menu by directional keys, and abundant information of operation prompt;

●Integrated input of English/number/sign, similar to T9 input mode of mobile phone;

●Optimized digital filtering feature and good temperature feature, effectively assuring the stability and high

precision of weighing data;

２
 XK3190－D18 Technical Parameters
●Complete set functions of measured parameter for general truck weighing indicator;

●Available to store 1000 sets of vehicle number, tare weight, 1000 sets of cargo names, 1000 sets of weighing

records and 50 sets of Overload RECs;

●Functions of storage, prompt intelligent inquiry and deletion for weighing records;

●Static weighing function per axle;

●Optional 10M/100M adaptive Ethernet interfaces, available for transmission and management of weighing

records through LAN and Internet Net;

●Optional USB data interface, available for connection with computer via USB data wire;

●Optional PS/2 keyboard interface, available for indicator operation via general PS2 keypad of computer.

13. Differences on the models of XK3190-D18 series indicators

m-type cast aluminum housing, single-window indicator,

XK3190-D18m1 Adoption of FSTN 240×64 Dot matrix LCD with high contrast,

No PS/2 interface, Ethernet interface or USB interface.

XK3190-D18m1+ m-type cast aluminum housing, single-window indicator,

Adoption of FSTN 240×64 Dot matrix LCD with high contrast,

With PS/2 interface, Ethernet interface and USB interface.

s-type waterproof s/s housing, single-window indicator,

XK3190-D18s1 Adoption of FSTN 240×64 Dot matrix LCD with high contrast,

No PS/2 interface, Ethernet interface or USB interface.

s-type waterproof s/s housing, single-window indicator,

XK3190-D18s1+ Adoption of FSTN 240×64 Dot matrix LCD with high contrast,

With PS/2 interface, Ethernet interface and USB interface.

m-type cast aluminum housing, double-window indicator,

XK3190-D18m2 Adoption of 6-bit & 0.8-inch LED display window + 128×96 Dot matrix LCD,

No PS/2 interface, Ethernet interface and USB interface.

m-type cast aluminum housing, double-window indicator,

XK3190-D18m2+ Adoption of 6-bit 0.8-inch LED display window + 128×96 Dot matrix LCD,

With PS/2 interface, Ethernet interface and USB interface.

３
 XK3190－D18 Installation and Connection

Chapter 2 Installation and Connection

I. Diagram for Indicator

(Fig. 2-1) Diagram for Front Panel of Single-window Indicator

XK3190-D18 Diagram for Double- window Indicator

The signs and characters on the panel should be transparent with black base.

(Fig. 2-2) Diagram for Front Panel of Double-window Indicator

 XK3190－D18 Installation and Connection

(Fig. 2-3) Diagram for Functions on Back Panel

II. Main Interface Display of Single-window Indicator (Weighing Interface)

VEH No.: 10 characters CGO No.: 10 characters Time

AA2006688 Good-quality steel 15:31:20

Weight value
3190.00 kg
Automatic Communication Inner code Stability Net weight Zero

Note: The main interface of double-window indicator is similar to that of single-window indicator, and only the layout

of displayed information is different.

III. Connection between Load cell and Indicator

1. D-sub 9 pin socket socket is used for the connection of load cells. The meaning of each pin is listed in Fig. 2-4.
2. +E and +S, E and -S must be short connected if 4-core shield cable is used.

５
XK3190－D18 Installation and Connection

▲The connection between load cell and indicator must be reliable and the shield cable must be

well grounded. The connecting line can not be plugged in and out when the indicator is powered

on in order to prevent any damage to the indicator or load cell by static electricity.
▲ The load cell and indicator are both static sensitive equipments, so anti-static measures must
be taken during the use. It is strictly forbidden to carry out welding operation or other
operations with high current on the weighing platform. In the stormy season, lightening
prevention measures must be taken reliably to prevent any damage to load cell and indicator
caused by lightening stroke, and to guarantee the personal security of operators and safe
running of weighing devices and relative equipments.

Fig. 2-4 Connecting Diagram of Load cell

６
 XK3190－D18 Measuring Operation
Chapter 3 Measuring Operation
I. Keyboard Chart

II. Instruction of Keyboard

In this instruction, 【××】 【××】refer to the key-pushing sequence. For example, 【Set】 【Input】 mean to push
【↓】
these keys 【Set】 【Input】in sequence. (【↑】
【↓】 【↓】 and 【←】
【→】are exception, which refers to execution
of selected operation according to the direction keys. And each arrow key may be pressed more than one time.
Here it is just as an indication), Under the operation status of main page, the functions under frequent use are realized
via the operation of single key, while the functions under infrequent use are realized via the key-pushing sequence.

Key Name Instruction

Input CGO No. setup in weighing mode;
【1 / ABC CGO No.】
Input number 1 or letter ABC under setup status
Input VEH No. setup in weighing mode;
【2/DEF VEH No.】
Input number 2 or letter DF under setup status
Input function setup menu in weighing mode;
【3 / GHI Set】
Input number 3 or letter GHI under setup status
Execute Fill PRT in weighing mode;
【4 / JKL Fill PRT】
Input number 4 or letter JKL under setup status
Execute Report Print in weighing mode;
【5/ MNO Report Print】
Input number 5 or letter MNO under setup status
Input Preset Tare set in weighing mode;
【6 / PQR Preset Tare】
Input number 6 or letter PQR under setup status
【7/STU Sum Print】 Execute Sum Print in weighing mode;
 XK3190－D18 Measuring Operation

Input number 7 or letter STU under setup status

Key Name Instruction
Execute Save Print in weighing mode;
【8/VWX Save Print】
Input number 8 or letter VWX under setup status
Input calibration setup in weighing mode
【9 / YZ Calibration】
Input number 9 or letter YZ under setup status
Turn on/off back light under non-setup status
【0 Back Light】
Input number 0 under setup status
【Tare】 Execute Tare operation in weighing mode
【Zero】 Zero operation in weighing mode
【Input mode】 Conversion input modes under setup status
【Check】 Input record check interface
【Input】 Save the input parameters
【Weighing】 Press this key to go back to main weighing interface.
【Clear】 Clear the records or clear one by one the input value
Realize reset function under AC power supply, and turn on/off the device under DC power
【On/off】
supply
【Save Tare】 Input interface of storing tare weight
【↑】 Direction key for previous page of menu or record
【↓】 Direction key for next page of menu or record
Direction key, back to the previous menu or Input the left menu bar
【←】
“Left sign” in the input mode of phoneticism and sign
Direction key, for the next menu or the right menu bar
【→】
“Right sign” in the input mode of phoneticism and sign
【Axle】 Confirm axle measurement
【Axle All】 Completion of axle measurement and display of total weight
【Select】 Conversion display of gross weight / net weight
【Roll】 For printing roll
When using PS2 keyboard, the conversion between keyboards can be realized. There will
【F1】
be a long prompting sound in the indicator if conversion is successful.
【F2】 Extension key for functions, temporary

III. Measuring Operation

1. Initialization and Auto Zero upon Start

８
 XK3190－D18 Measuring Operation

(1) When power-on, the indicator indicates start image and then Inputs weighing status in several seconds
automatically.
(2) When the device is turned on, if the weight deviates from zero but still within the zero parameter scope, the
indicator will automatically return to zero. Please see the Chapter: Menu Operation for the details of parameter
selection and setting method of zero scope upon start,
2. Manual Zero (Semi-automatic Zero)
(1) Push 【Zero】key and the indicator returns to zero. The zero sign is on at this time.
(2) When the indicating value deviates from zero but still within zero scope, the 【Zero】 key is enable, otherwise
it is not. Please see the Chapter: Menu Operation for the details of parameter selection and setting method of
zero scope upon start.
(3) Only when the stability sign is on, the zero operation can be executed.
(4) If the tare weight of the indicator is not zero, first press 【Preset Tare】 key and set the value as 0. Zero setting
can’t be performed until back to the weighing interface.
3. Operation of Tare Function
Three tare methods are provided by the indicator:
(1) General Tare:
In weighing mode, when the indicating weight is positive and stable, press the【Tare】 key, then the indicating
weight will be deducted as tare weight. At this time, the indicator indicates the net weight as 0 with the weight
sign on.
(2) Preset Tare:
Under the gross weight status of weighing interface, press the 【Preset Tare】 key and then the indicator Inputs
interface of Preset Tare. At this time, the indicating tare weight value is the original tare value. If a new tare
value is required to be set, use the number keys to input once again and then press the 【Input】key for
confirmation. Press 【←】 key for back to weighing interface. As for detailed setting method, please see the
Chapter: Menu Operation.
(3) Calling Tare Weight According to VEH No.:
In weighing mode, press the 【VEH No.】 key and the indicator inputs setting interface for VEH No./Tare. After
inputting correct VEH No., press 【Input】 key to call the relative tare weight value of this VEH No. from the
memory. If there is no need to revise the tare weight, press 【Tare】key to take the tare weight value as the
current tare weight and meanwhile return to weighing interface.
4. Measuring Operation for Axle
D18 has the measuring function of axle.
First, set the parameters of “measuring function of axle” to “using measuring of axle” according to the method
described in the chapter “Menu Operation”, and set the “unblocking threshold of axle” to the required value.
After pressing 【Weighing】 key for back to weighing status, the indicator Inputs axle measuring with the sign
of “axle ” on. The steps are as follows:
９
 XK3190－D18 Measuring Operation

(1) The first group of axle is moved on the platform for measuring. After it stops, wait until the stability light of the
indicator on. Then press 【Axle】key to lock and record the value;
(2) Remove the first group of axle from the platform and the axle locking is disable. The indicator returns to zero. Then
put the second group of axle on the platform and repeat the operation of Step (1);
(3) After measuring all axles, press 【Axle All】 key. The indicator displays the 【Truck Weight】sign and the whole
car load. Press 【Save Print】 key to save and print the weight. Pres【Weighing】 key to Input new measuring status
of axle again.

１０
 XK3190－D18 Menu Operation
Chapter 4 Menu Operation
Among XK3190-D18 series, the menu items of double-window indicator are
same as that of single-window indicator, so is the operation method. The only
difference is the layout sequence on the display. The operation of menu items of
single-window indicator is mainly described below.

I. General Menu List

Factory Default
Key Operation Menu Items Sub-menu
Setting
【CGO No.】 『Cargo Name』 -
【VEH No.】 『VEH No./Tare』 -
【Save Print】 『Save Print Set』 -
【Preset Tare】 『Preset Tare』 0
【Save Tare】 『VEH No./Tare』 -
『Report by Time』 『Report Print』 -
『Report 1』 -
『Report 2』 -
【Report Print】 『Report 3』 -
『Report 4』 -
『Report 5』 -
『Report 6』 -
【Calibration】 『CAL PWD』 888888
『Division』 1
『Number of Decimal Point』 3
『Calibration』 『F.S』 3000
『Zero』
『Loading』 3000
『Zero Track Speed』 0
『Zero Track Range』 0.5
『Manu Zero Set』 4%
『Initial Zero Set』 20%
『Filter Degree』 2
 XK3190－D18 Menu Operation

『Unit』 kg
『A/D Ivert Rate』 50Hz
『Signal Range』 10mV
『Applicate Range』 Not for trade
『Zero Point』 99545
『Calibrate Para.』 『CAL Coefficient』 0.02094
『Nonlinear』 1.00000
『REC Search』 『Record Search』 -
『VEH No. Search』 -
『CGO No. Search』 -
【Check】 『Overload REC』 -
『Scan Record』 -
『Delete All』 -
『Delete Overload』 -
【Set】 FUNC PWD 888888
『Print Method』 Manual Print
『Printer Type』 Microprinter
『Back Zero Limit』 50
『Print Setup』
『Print Format』 3Link Format
『Min. PRT Weight』 0.010
Fill PRT is not
『Fill PRT Option』
applied.
『Comm Method』 Continuous mode
『Comm Setup』 『Comm Address』 1
『Baud Rate』 1200
『USB Setup』 USB function disable
『Net Enable』 Net function disable
『IP Address』 192.168.002.175
『Net Setup』 『Subnet Mask』 255.255.255.000
『MAC Address』 3190
『Default Gateway』 192.168.002.001
Date/Time Setup 『CAL PWD』 888888

１２
 XK3190－D18 Menu Operation

【Date/Time Setup】 08/01/01 1:30:30

Date/Time Disp Time Display
CGO No. Enable Use of CGO No.
VEH No. Enable Use of VEH No.
Axle measuring is not
Axle Mode Enable
used.
Axle Lock Value 1%
Display Contrast 5
LED Brightness 4
CAL PWD Change 888888
Time PWD Change 99/99/99
Shanghai Yaohua
Company Name Weighing System Co.,
Ltd.
Inner Code -
Micropri Test -
System Test
Software -
Note: 【***】 in the table refers to the corresponding push-key; 【***】 refers to the name of menu bar displayed on
screen, belonging to the first-level menu; 【***】 refers to the set menu of parameter value, belonging to the
second-level menu.
Note: The factory default can be restored according to the following operation when the
indicator runs abnormally because of the wrong set of parameter value or memory fault.
Push 【Calibration】 in weighing mode and input password “100000”, then push 【Input】
key. The indicator displays “Initialization” and this process begins. Do not push any key at
this time and wait for about 2 minutes. The indicator parameters are then restored to
default.

II. Instruction of Operational Mode of Indicator

The indicator provides three operational modes according to the spot operation of truck weighing in order to finish
all operations more quickly, intelligently and conveniently.
1. Single-key Function Mode
Relative operation can be executed by directly pushing one function key.
Corresponding function keys: 【Fill PRT】, 【Zero】, 【Tare】, 【Back Light】, 【Axle】,【Tare All】, 【Select】,
【Roll】, 【Weighing】, 【Input mode】
For example: Push 【Zero】 key in weighing mode to execute zero operation.

１３
 XK3190－D18 Menu Operation

2. Single-key Menu Mode:

For the operation requiring input parameters, just push one function key to Input the corresponding interface of
parameter set.
Corresponding Function keys: 【CGO No.】, 【VEH No.】, 【Save Tare】, 【Preset Tare】, 【Save Print】
For example: Push 【CGO No.】 in weighing mode to directly Input the following interface of 『Cargo Name』 for
setting. The input area highlighted and the input status is displayed in the upper right of the screen. Users can push
【Input mode】 to switch the method. And then input number/English/character/sign according to the input mode.
Then push 【Input】key to keep the input content and then push 【←】key to the main interface.

Cargo Name 【123】

Val: Good-quality Steel Code: 0
Input cargo name
【←】Back 【Input】Confirm

3. Management Mode of Menu Bar

As for the setting of parameters which are not used often but complicated, unified management can be carried
out through the menu bar, which shall be convenient for the users to search according to the parameter types.
According to different functions, five function keys are set for menu management. See the above list for menu
structure.
Corresponding Keys: 【Set】, 【Check】, 【Report Print】, 【Calibration】, 【Clear】
For example: Push 【Set】 key in weighing mode and input the password to Input the following menu structure.
Similar to the interface of the mobile phone, the highlighted refers to the current selected menu item.
Push direction keys to move the optional bar and select the pre-set menu item according to the following
operation prompts on the screen.
Print Setup Date/Time Setup
Comm Setup Date/Time Display
USB Setup CGO No. Enable
Net Setup 【↑】Option 【Input】Confirm
And then push 【Input】 to Input the interface of menu setup or the next menu optional bar. If 『CGO No. Enable』
is required to be set, move the display bar to corresponding menu item. See the following chart:

Print Setup Date/Time Setup

Comm Setup Date/Time Display
USB Setup CGO No. Enable
Net Setup 【↑】Option 【Input】Confirm
Then push 【Input】 and 【↑】【↓】 keys to select the VAL.

１４
 XK3190－D18 Menu Operation

CGO No. used

CGO No. not used
【←】 Back 【↑】 Option 【Input】 Confirm
Push 【Input】 key to save and then push 【←】 key back to the previous menu or push【Weighing】 key to
directly return to the weighing mode.

III. Instruction of Menu Operation

1. 『Cargo Name』 Setup
Under weighing interface, push 【CGO No.】, then the indicator displays:
Cargo Name 【123】
VAL: Good-quality Steel Code: 1
Input cargo name
【←】Back 【Input】Confirm
Push 【Input】 key,
Cargo Name 【123】
VAL: Good-quality Steel Code: 1
Input code for cargo
【←】Back 【Input】 Confirm

When the input area highlighted, it indicates that the value can be input here.
After inputting value in the set area and pushing 【Input】 key, the indicator shall automatically search whether there is
corresponding code in the memory. If so, relative code will be indicated; if not, new code will be formed and indicated.
If user knows the corresponding code of the VAL, he can directly input it in the code area. Then the indicator shall
automatically search the corresponding VAL and indicate it, which will avoid relatively complex operation of input
mode.
If the code is input and there is no corresponding CGO No. searched, the indicator shall indicate “fault”.
Push 【Input】 key for confirmation after input and then push 【←】 key for going back to the weighing interface.
Input Area Input mode Remarks
VAL Number/English/Sign 10 characters can be input at most.
Code Number Three numbers can be input at most.

2. 『VEH No. / Tare』 Setup

Under weighing interface, push 【VEH No.】 or 【Tare Memory】 keys and then the indicator displays:

１５
 XK3190－D18 Menu Operation

VEH No./Tare 【123】

VEH: E A12345 Code: 0
Tare: 1000kg
【←】Back 【Input】 Confirm

Push 【Input】 key,

VEH No./Tare 【123】
VEH: E A12345 Code: 0
Tare: 1000kg
【←】Back 【Input】 Confirm
Push 【Input】 key,
VEH No./Tare 【123】
VEH: E A12345 Code: 0
Tare: 1000kg
【←】Back 【Input】 Confirm

Input Area Input mode Remarks

VEH No. Number/English/Sign 10 characters can be input at most.
Code Number Three numbers can be input at most.
Tare Number Six numbers can be input at most.

When the input area is highlighted, it indicates that the value can be input here. Either VEH No. or code can be
input.
After inputting value in the VEH No. area and pushing 【Input】 key, the indicator shall automatically search
whether there is corresponding code in the memory. If so, relative code will be indicated; if not, new code will be
formed and indicated. If user knows the corresponding code of the VEH No., he can directly input it in the code area.
Then the indicator shall automatically search the corresponding VEH No. and indicate it, which will avoid relatively
complex operation of input mode.
If the code is input and there is no corresponding VEH No. searched, the indicator will indicate “fault”.
The VEH No. can be input with mixture of English and number. And input mode can be switched by pushing
【Input mode】 key.
After inputting the VEH No. and code, it is switched into tare weight setting automatically. The tare weight column
indicates the corresponding value of the above saved VEH No. If there is no memory, the default tare weight is 0. If the
tare weight value needs to be changed, input directly the new tare weight and push 【Input】 to keep the VAL and then
push 【←】 back to the weighing mode.
１６
 XK3190－D18 Menu Operation

If the code of VEH No. is 0, it indicates single cargo weighing and tare weight value can not be input.
3. Save Print Setup
Print Information 【123】
VEH: A12345 Code: 1
CGO: --- Code: 1
【←】Back 【Input】 Confirm
Push 【Input】 key,
Print Information 【123】
VEH: A12345 Code: 1
CGO.: --- Code: 1
【←】Back 【Input】 Confirm
Push 【Input】 key,
Print Information 【123】
VEH: A12345 Code: 1
CGO: --- Code: 1
【←】Back 【Input】 Confirm
Push 【Input】 key,
Print Information 【123】
VEH: A12345 Code: 1
CGO.: --- Code: 1
【←】Back 【Input】 Confirm

Input Area Input mode Remarks

VEH Number/English/Sign 10 characters can be input at most.
Code (upper) Number 3 characters can be input at most.
CGO No. Number/English/Sign 10 characters can be input at most.
Code (lower) Number 3 characters can be input at most.
When the input area is highlighted, it indicates that the value can be input here. Either VEH No. / CGO No. or code
can be input.
After inputting value in the VEH No./CGO No. area and pushing 【Input】 key, the indicator shall automatically
search whether there is corresponding code in the memory. If so, relative code will be indicated; if not, new code will
be formed and indicated. If user knows the corresponding code of the VEH No./CGO No., he can directly input it in the
code area. Then the indicator shall automatically search the corresponding VEH No. /CGO No. and indicate it, which
will avoid relatively complex operation of input mode.
If the code is input and there is no corresponding VEH No. / CGO No. searched, the indicator shall indicate “fault”.

１７
 XK3190－D18 Menu Operation

The VEH No. can be input with mixture of English and number. And input mode can be switched by pushing 【Input
mode】 key.
After completion of switch in four input areas, push 【Input】 key to keep the VAL and execute Save Print operation;
if pushing 【←】 key, the print shall be cancelled and return to weighing interface. For the detailed operating rules of
Save Print, please refer to the chapter Printing & Records.
4.『Preset Tare』 Setup
In weighing mode, push 『Preset Tare』 to Input the following interface,
Preset Tare 【123】
VAL: 0.000kg
Input preset tare value
【←】Back 【Input】 Confirm

Input Area Input mode Remarks

VAL Number Six numbers can be input at most.
After input Preset Tare value with number keys, push 【Input】 key to keep the VAL and then push 【←】 key for
returning to weighing interface. If the Preset Tare is not 0, net weight value shall be indicated in the weighing interface
with the sign for net weight on. If the Preset Tare is 0, the gross weight value shall be indicated. If the Preset Tare is not
the integral multiple of the scale division value, the indicator will automatically round up to an integral multiple of the
scale division value.
5. Report Print Setup
In weighing mode, push 【Report Print】key to Input the following interface:
Report by Time Report 4
Report 1 Report 5
Report 2 Report 6
Report 3 【↑】 Option 【Input】 Confirm

VAL Remarks
Report by time Print the weighing record periodically and print total three reports in different formats.
Report 1 Print in queque as per the save time of records
Report 2 Print in queque as per VEH No.
Report 3 Print in queque as per CGO No.
Report 4 Print correspondent table between VEH No. and shortcut code.
Report 5 Print correspondent table between CGO No. and shortcut code.
Report 6 Print all Overload RECs.

Push 【↑】【↓】 keys to move the highlighted to select the report type.
１８
 XK3190－D18 Menu Operation

(1) After choosing 『Report by Time』 and pushing 【Input】, the screen displays:
Report Print 【123】
From: 07 / 12 / 04
To: 07 / 12 / 04
【←】Back 【Input】 Confirm

Input Area Input mode Remarks

Input 6-digit date value and display it while shifting towards left, with 2
VAL Number digits respectively for year, month and day.
For example: if the date is December 4, 2007, then input “071204”.

Input the period of print record, and print all correspondent records of this period after pushing 【Input】 key. Return
to weighing interface after print; push 【←】 key to cancel the print operation, and directly return to the weighing
interface.
(2) When choosing other report type, push 【Input】 key to print it in relative format. After print, it returns to
weighing interface automatically; push 【←】 key to cancel the print operation and directly return to the weighing
interface. See the appendix for the print format of reports.
6. Calibration Setup
First, turn the calibration switch to make it allow for calibration. In weighing mode, push 【Calibration】, the
indicator displays:
CAL PWD 【123】
VAL: ******
Input correct CAL PWD with number keys
【←】Back 【Input】 Confirm

Input Area Input mode Remarks

Input 6-digit password, with each "*" standing for 1 digit. Only the first
VAL Number 6 digits are defaulted when inputting more than 6 digits. The initial
password is "888888"
After inputting correct password, push 【Input】 key to Input calibration set interface. If the password is wrong, input it
once again according to the requirement. If fault is made for three times, it will go back to weighing interface. Push
【←】 key to directly return to weighing interface.
Calibration setup interface is as follows:

１９
 XK3190－D18 Menu Operation

Calibration Zero Scope upon Initialization

Zero Track Speed Filter Degree
Zero Track Scope Unit
Zero Scope
【↑】 Option 【Input】 Confirm
(1) Calibration
See the chapter 【Calibration】 for detailed calibration method.
(2) Zero Track Speed
Push 【↑】【↓】 keys to move the optional bar to 『Zero Track Speed』and then push 【Input】 to display the
following interface:
Zero Track Speed 【123】
VAL: 0
(From 0 to 4)
【←】Back 【Input】 Confirm

Input Area Input mode Remarks

One number can be input at most.
VAL Number Only the numbers 0, 1, 2, 3 and 4 can be input; and fault will be caused if other
number is input.
After inputting through number keys, push 【Input】 key to save and 【←】 key for going back to the function menu.

(3) Zero Track Scope

Push 【↑】
【↓】 keys to move the optional bar to 『Zero Track Scope』 and push 【Input】 key to display the
following interface.
Zero Track Scope 【123】
VAL: 0.5e
(From 0.0 to 4.5, 0.5/Interval)
【←】Back 【Input】 Confirm

Input Area Input mode Remarks

2 numbers can be input at most.
VAL Number Only 0.0, 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0 and 4.5 can be input, and fault will be
caused if other number is input.
Push 【Input】 key to save after inputting through number keys . Push 【←】 key not to save and return to function
menu.

２０
 XK3190－D18 Menu Operation

(4) Manu Zero Set

Push 【↑】
【↓】 keys to move the optional bar to 『Zero Scope』and then push 【Input】 key to display the following
interface:
Zero Scope 【123】
VAL: 20%
(0,2,4,10,20,40,100 select)
【←】Back 【Input】 Confirm

Input Area Input mode Remarks

3 numbers can be input at most.
VAL Number Only 0, 2, 4, 10, 20, 40 and 100 can be input, and fault will be caused if other number
is input.
Push 【Input】 key to save after input through number keys. Push 【←】 key not to save and return to function menu.

(5) Initial Zero Set

Push 【↑】
【↓】 keys to move the optional bar to 『Zero Scope upon Initialization』and then push 【Input】 key
to display the following interface:
Zero Scope upon Initialization 【123】
VAL: 2%
(0,2,4,10,20,40,100 select)
【←】Back 【Input】 Confirm

Input Area Input mode Remarks

3 numbers can be input at most.
VAL Number Only 0, 2, 4, 10, 20, 40 and 100 can be input, and fault will be caused if other number
is input.
Push 【Input】 key to save after input through number keys. Push 【←】 key not to save and return to function menu.

(6) Filter Degree

Push 【↑】
【↓】 keys to move the optional bar to 『Filter Degree』and then push 【Input】 key to display the
following interface:
Filter Degree 【123】
VAL: 2
From 0 to 4
【←】Back 【Input】 Confirm

２１
 XK3190－D18 Menu Operation

Input Area Input mode Remarks

One number can be input at most and the Filter Degree is limited between 0 and 4.
The bigger the value, the more stable the weight value will be, but the reaction
VAL Number speed is lower; the faster the reaction speed, the worse the stability will be; so
comprehensive consideration should be made according to the stability and reaction
speed when setting the value.
Push 【Input】 key to save after input through number keys. Push 【←】 key not to save and return to function
menu.
(7) Unit
Push 【↑】
【↓】 keys to move the optional bar to 『Unit』and then push 【Input】 key to display the following
interface:
kg
t
lb
【←】Back 【↑】 Option 【Input】 Confirm

VAL Remarks
kg “kg” unit for indicator display and weighing record.
t “t” unit for indicator display and weighing record.
lb “lb” unit for indicator display and weighing record.
【↓】 keys to select unit and 【Input】 key to save. Push 【←】 key for going back to the previous menu.
Push 【↑】
(8) A/D Convert Rate
Push 【↑】
【↓】 keys to move the optional bar to 『A/D Convert Rate』and then push 【Input】 key to display
the following interface:

VAL Remarks
50Hz A/D convert rate is 50HZ.
100Hz A/D convert rate is 100HZ.
150Hz A/D convert rate is 150HZ.
200Hz A/D convert rate is 200HZ.
Push 【Input】 key to save after input through number keys. Push 【←】 key not to save and return to function menu.

(9) Signal Range

Push 【↑】【↓】 keys to move the optional bar to 『Signal Range』and then push 【Input】 key to display the
following interface:
２２
 XK3190－D18 Menu Operation

10mV
20mV
【←】Back 【Input】 Confirm

VAL Remarks
10mV The signal source scope of load cell is -10mV～10mV.
20mV The signal source scope of load cell is -20mV～20mV.
Push 【Input】 key to save after input through number keys. Push 【←】 key not to save and return to function
menu.
(10) Applicate Range
Push 【↑】【↓】 keys to move the optional bar to 『Applicate Range』and then push
【Input】 key to display the following interface:

Not for Trade

Trade Purpose
【←】Back 【↑】 Option 【Input】 Confirm

VAL Remarks
Not for Trade Non-law related operations are allowed on non-trade occasions.
For Trade Non-law related operations are invalid for trade.
Push 【Input】 key to save after input through number keys. Push 【←】 key not to save and return to function
menu.
(11) Calibrate Para.
The parameter status after calibration can be examined or revised in this menu. Push 【↑】
【↓】 keys to move the
optional bar to 『Calibrate Para.』and then push 【Input】 key to display the following interface:
Zero 【123】
VAL: 2145
(Input zero AD code)
【←】Back 【Input】 Confirm

２３
 XK3190－D18 Menu Operation

Input Area Input mode Remarks

VAL Number 6 digits can be input at most. The value can be modified only when replacement of
indicator instead of re-calibration is made. The zero value must be set according to
the parameter of the substituted indicator.
To assure the measuring precision of the indicator, it is better to re-label after
indicator substitution.
Press 【Input】 key,
CAL Coefficient 【123】
VAL: 0.44336
Input CAL coefficient of indicator
【←】Back 【Input】 Confirm

Input Area Input mode Remarks

VAL Number 6 digists can be input at most. The value can be modified only when replacement of
indicator instead of recalibration is made. The CAL coefficient must be set according to
the parameter of the substituted indicator.
To assure the measuring precision of the indicator, it is better to re-label after
indicator substitution.
Press 【Input】 key.
Non-lineary 【123】
VAL: 1.00000
(Input non-linearity)
【←】Back 【Input】 Confirm

Input
Input Area Remarks
mode
6 digits can be input at most with the scope between 0.99500～1.00500.
Definition of non-lineary revised value:
Revised value=1 + weight deviation of half F.S. / F.S. value
For example:
VAL Number
When the F.S. value is 30000, but the actual half F.S. is 1505, then
Non-linear revised value=1 + 5/3000=1.00167;
When the F.S. value is 30000, but the actual half F.S. value is 1495, then
Non-linear revised value=1 - 5/3000=0.99833.

7. Function Parameter Setup

２４
 XK3190－D18 Menu Operation

In weighing mode, push 【Set】 key and input correct FUNC PWD (888888) to Input menu bar of function
parameter.
Print Setup Date/Time Setup
Comm Setup Date/Time Display
USB Setup CGO Enable
Net Setup 【↑】 Option 【Input】 Confirm

Push 【↑】【↓】 keys for turning pages.

VEH No. Enable LED Brightness
Axle Mode Enable CAL PWD Change
Axle Lock Value Time PWD Change
Display Contrast of 【↑】 Option 【Input】 Confirm

Push 【↑】【↓】 keys for turning pages,

Company Name
Inner Code
System Test
PS/2 Enable 【↑】 Option 【Input】 Confirm

(1) Print Setup

Push 【↑】
【↓】 keys to select 『Print Setup』 and then push【Input】to Input Print Function menu. Push 【←】
key to return to the previous menu.
Print Method Min. PRT Weight
Printer Type Fill PRT Option
Back Zero Limit
Print Format 【↑】 Option 【Input】 Confirm

1) Print Method
Push【↑】
【↓】keys to move the optional bar to『Print Method』and then push【Input】key to display the following
interface:
Automatic Print
Manual Print
【←】 Back 【↑】 Option 【Input】 Confirm

２５
 XK3190－D18 Menu Operation

VAL Remarks
Auto Print Automatically print and save the weighing data during the weighing process.
Manual Print Push 【Save Print】 or 【Fill PRT】 during the weighing process print and save the
weighing data.
Push【↑】
【↓】keys to select relative setup and then push【Input】key. The indicator saves parameters automatically.
Then push 【←】 key for going back to the previous menu. Push 【Weighing】 key to return to weighing interface. In
this instruction, the method for optional parameter setup is same as the above.

2) Printer Type
Push 【↑】【↓】 keys to move the optional bar to 『Printer Type』 and then push 【Input】 key to display the
following interface:
Print Invalid EPSON LQ-1600K
Microprinter
Psonic KX－P1131
EPSON LQ-300K 【↑】 Option 【Input】 Confirm

VAL Remarks
Print Invalid Print function is invalid in this indicator.
Microprinter Built-in micro microprinter is applied.
Psonic KX-P1131 Panasonic KX-P1131 model printer is used.
EPSON LQ-300K EPSON LQ-300K model printer is used.
EPSON LQ-1600K EPSON LQ-1600K model printer is used.
Push 【↑】
【↓】 keys to select relative set and then push 【Input】 key. The indicator saves parameters automatically.

3) Zero Limit for Print

Push 【↑】
【↓】 keys to move the optional bar to 『Zero Limit for Print』 and then push 【Input】 key to display
the following interface:
Zero Limit for Print 【123】
VAL: 0%
(Input judging scope for zero: 0～100)
【←】 Back 【Input】 Confirm

２６
 XK3190－D18 Menu Operation

Input Area Input mode Remarks

VAL Number 3 digits can be input at most with the scope between 0-100. The indicator
shall report fault if beyond this scope. 0 means printing available only when
resetting to zero, while 100 refers to no limit.
After inputting by number keys, push 【Input】 key to save the parameters.

4) Option of Print Format

Push 【↑】
【↓】 keys to move the optional bar to 『Option of Print Format』 and then push 【Input】 key to display
the following interface:
Record Format
1 Link format
2 Link draft format
3 Link Format 【↑】 Option 【Input】 Confirm

VAL Remarks
Weighing record is printed according to record format. See the appendix for relative
Record Format
format instruction.
Weighing record is printed according to one link format. See the appendix for relative
1Link Format
format instruction.
Weighing record is printed according to link format. See the appendix for relative
2Link draft Format
format instruction.
Weighing record is printed according to link format. See the appendix for relative
3Link Format
format instruction.
Push 【↑】
【↓】 keys to select relative setup and then push 【Input】 key. The indicator saves parameters automatically.

5) Min. PRT Weight

Push 【↑】
【↓】 keys to move the optional bar to 『Min. Print Weight』 and then push 【Input】 key to display
the following interface:
Min. PRT Weight 【123】
VAL: 0.010kg
(VAL ≥10e )
２７
 XK3190－D18 Menu Operation

【←】 Back 【Input】 Confirmation

Input
Input Area Remarks
mode
6 digits can be input at most and the maximum print weight must be not less than 10
divisions.
VAL Number
Every time after completion of calibration, the indicator correct automatically the min. VAL
of min. print weight as per the set scale division value.
After inputting via number keys, push 【Input】 key to save the parameters.

6) Fill PRT Option

Push 【↑】
【↓】 keys to move the optional bar to 『Fill PRT Option』 and then push 【Input】 key to display the
following interface:
Fill PRT not applied.
Fill PRT applied.
【←】 Back 【↑】 Option 【Input】 Confirm

VAL Remarks
Fill PRT not applied Fill PRT mode is not applied in printer. See appendix for relative print modes.
Fill PRT applied Fill PRT mode is applied in printer. See appendix for relative print modes.
Push 【↑】
【↓】 keys to select relative set and then push 【Input】 key. The indicator saves parameters automatically.

(2) Comm Setup

Push 【↑】【↓】 keys to select 『Comm Setup』 and then push 【Input】,
Comm Method
Comm Address
Baud Rate
【←】 Back 【↑】 Option 【Input】 Confirm
1) Comm Method
Push 【↑】
【↓】 keys to move the optional bar to 『Comm』 and then push 【Input】 key to display the following
interface:

Command Mode

２８
 XK3190－D18 Menu Operation

Continuous mode
【←】 Back 【↑】 Option 【Input】 Confirm

VAL Remarks
Command mode is adopted for the communication mode between the indicator and upper
Command mode
computer. See the chapter Communication for instruction of relative communication modes.
Continuous mode is adopted for the communication mode between the indicator and upper
Continuous mode
computer. See the chapter Communication for instruction of relative communication modes.

Push 【↑】
【↓】 keys to select relative set and then push 【Input】 key. The indicator saves parameters automatically.
2) Comm Address
Push 【↑】
【↓】 keys to move the optional bar to 『Comm Address』 and the push 【Input】 key to display the
following interface:

Comm Address 【123】

VAL: 1
(From 1to 26)
【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

2 digits can be input at most and the scope for communication address is limited
VAL Number
between 1 and 26.
After inputting via number keys, push 【Input】 key to save the parameters.
3) Baud Rate
Push 【↑】
【↓】 keys to move the optional bar to 『Baud Rate』 and then push 【Input】 key to display the following
interface:
Baud Rate 【123】
VAL: 1200 b/s
(Input 600, 1200, 2400. 4800 and 9600)
【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

4 digits can be input at most.
VAL Number Only 600, 1200, 2400. 4800 and 9600 can be input and fault will be caused if other
number is input.

２９
 XK3190－D18 Menu Operation

After inputting via number keys, push 【Input】 key to save the parameters.

(3) USB Setup

Push 【↑】【↓】 keys to move the optional bar to 『USB Setup』 and then push 【Input】 key to display the
following interface:
USB Disable
USB Disable
【←】 Back 【↑】 Option 【Input】 Confirm

VAL Remarks
USB disable Communication between USB and upper computer is allowed.
USB disable Communication between USB and upper computer is forbidden.

Push 【↑】
【↓】 keys to select relative set and then push 【Input】 key. The indicator saves parameters automatically.

(4) Net Setup

Push 【↑】【↓】 keys to move the optional bar to 『USB Setup』 and then push 【Input】 key to display the
following interface:

Net Enable Default Gateway

IP Address
Subnet Mask
MAC Address 【↑】Option 【Input】 Confirm

1) Push 【↑】
【↓】 keys to select 『Net Function』 and then push 【Input】 key,
Net Disable
Net Disable
【←】 Back 【↑】 Option 【Input】 Confirm

VAL Remarks
Net Disable Communication through Ethernet is forbidden for the indicator.
Net Disable Communication through Ethernet is allowed for the indicator.
Push 【↑】
【↓】 keys to select relative set and then push 【Input】 key. The indicator saves parameters automatically.

2) Push 【↑】
【↓】 keys to select 『IP Address』 and then push 【Input】 key,
３０
 XK3190－D18 Menu Operation

IP Address 【123】
VAL: 192.168.002.175
(IP ADDR,range:000-255)
【←】 Back 【Input】 Confirmation

Input Area Input mode Remarks

Input IP address of the indicator with number keys and total 12 numbers are
VAL Number
required to be input.
After inputting via number keys, push 【Input】 key to save the parameters.

3) Push 【↑】
【↓】 keys to select 『Subnet Mask』 and then push 【Input】 key,
Subnet Mask 【123】
VAL: 255.255.255.000
(Subnet Mask,range:000-255)
【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

The Subnet Mask is input with number keys and total 12 numbers are required to be
VAL Number
input.
After inputting via number keys, push 【Input】 key to save the parameters.

4) Push 【↑】
【↓】 keys to select 『MAC Address』 and then push 【Input】 key,

MAC Address 【123】

VAL: 3190
(MAC Address:0-9999999)
【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

VAL Number MAC address of the indicator is input with number keys.
After inputting via number keys, push 【Input】 key to save the parameters.

5) Push 【↑】
【↓】 keys to select 『Default Gateway』 and then push 【Input】 key,

３１
 XK3190－D18 Menu Operation

Default Gateway 【123】

VAL: 192.168.002.001
(Gateway range:000-255)
【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

Default gateway of the indicator is input with number keys and total 12 numbers are
VAL Number
required to be input.
After inputting via number keys, push 【Input】 key to save the parameters.

(5) Date/Time Setup

Push 【↑】
【↓】 keys to select 『Date/Time Setup』and push 【Input】 key to Input the password protection
status. CAL PWD is required to be input.

FUNC PWD 【123】

VAL
(Input correct FUNC PWD)
【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

Input 6-digit password “888888”, and each “*” stands for 1 number.
VAL Number
The first 6 digits are defaulted if over 6 digits are input.
After inputting correct FUNC PWD, push 【Input】 key,
Date/Time Setup 【123】
Date: 06 / 08 / 31
Time: 20 : 16 : 53
【←】 Back 【Input】 Confirm

After inputting date, push 【Input】 key to save it and then display,
Date/Time Setup 【123】
Date: 06 / 08 / 31
Time: 20 : 16 : 53
【←】 Back 【Input】 Confirm

３２
 XK3190－D18 Menu Operation

Input Area Input mode Remarks

Input 6-digit date value and display it while shifting towards left, with 2 digits
Date Number respectively for year, month and day.
For example: if the date is November 17, 2006, then input “061117”.
Input 6-digit time value and display it while shifting towards left, with 2 digits
Time Number respectively for hour, minute and second.
For example: if the time is 13:08:30, then input “130830”.
After inputting time, push【Input】key to save it and then the date is displayed cyclically. Push 【←】for returning
to the previous menu.

(6) Date/Time Display

Push 【↑】【↓】 keys to select 『Date/Time Display』and push 【Input】 key.
Time Display
Date Display
Neither displayed
【←】 Back 【↑】 Option 【Input】 Confirm

VAL Remarks
Time Display Display the current time under weighing interface
Date Display Display the current date under weighing interface
Neither displayed Neither time nor date is displayed under weighing interface
Push 【↑】
【↓】 keys to select relative set and then push 【Input】 key. The indicator saves parameters automatically.

(7) CGO No. Disable

Push 【↑】【↓】 keys to select 『CGO No. Disable』and push 【Input】 key.

CGO No. not applied

CGO No. applied
【←】 Back 【↑】 Option 【Input】 Confirm

３３
 XK3190－D18 Menu Operation

VAL Remarks
CGO No. applied Cargo name can be set in the indicator and CGO No. shall be displayed in the print.
CGO No. not Cargo name is forbidden to set in the indicator and CGO No. shall not be displayed in the print.
applied The【CGO No.】 key has no function of setting CGO No. in weighing mode.

Push 【↑】
【↓】 keys to select relative set and then push 【Input】 key. The indicator saves parameters automatically.

(8) VEH No. Enable

Push 【↑】【↓】 keys to select 『VEH No. Enable』and push 【Input】 key.

VEH No. not applied

VEH No. applied
【←】 Back 【↑】 Option 【Input】 Confirm

VAL Remarks

VEH No. name can be set in the indicator and VEH No. shall be displayed in the print.
VEH No. applied
VEH No. name is forbidden to set in the indicator and VEH No. shall not be displayed
VEH No. not applied in the print.
The 【VEH No.】 key has no function of setting VEH No. in weighing mode.
Push 【↑】
【↓】 keys to select relative set and then push 【Input】 key. The indicator saves parameters automatically.

(9) Axle Enable

Push 【↑】【↓】 keys to select 『Axle Enable』and push 【Input】 key.

Axle not applied

Axle applied
【←】 Back 【↑】 Option 【Input】 Confirm

３４
 XK3190－D18 Menu Operation

VAL Remarks

Axle not applied The indicator Inputs normal measuring mode.

Axle applied The indicator Inputs static axle mode.

Push 【↑】
【↓】 keys to select relative set and then push 【Input】 key. The indicator saves parameters automatically.

(10) Axle Lock Value

Push 【↑】【↓】 keys to select 『Axle Lock Value』and push 【Input】 key.
Axle Lock Value 【123】
VAL: 0%
(From 0 to 100)
【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

3-digits can be input at most. The axle unlocking threshold is limited
VAL Number between 0-100%.
The percentage refers to the proportion of locked axle value.
Push 【↑】
【↓】 keys to select relative set and then push 【Input】 key. The indicator saves parameters automatically.

(11) Contrast of Display

Push 【↑】【↓】 keys to select 【Display Contrast】and push 【Input】 key.
Contrast of Display 【123】
VAL: 4
(From 0 to 9)
【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

1- digit can be input at most and the contrast of display is limited
2- to 0-9;
VAL Number
The number 0 means that the contrast of screen is the lowest;
The number 9 means that the contrast of screen is the highest.
After inputting with number keys, push 【Input】 key to save the parameters.

(12) Display contrast

Push 【↑】【↓】 keys to select 『Display contrast』and push 【Input】 key.
３５
 XK3190－D18 Menu Operation

Display contrast 【123】

VAL: 4
(Input display contrast: 0-7)
【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

1-digit can be input at most and the display contrast is limited to 0-7;
The number 0 means that the brightness of screen is the lowest;
VAL Number
The number 7 means that the brightness of screen is the highest.
This setup is only applicable for double-window indicator—D18!
After inputting with number keys, push 【Input】 key to save the parameters.

(13) CAL PWD Exchange

Push 【↑】【↓】 keys to select 『CAL PWD Change』and push 【Input】 key.
CAL PWD 【123】
VAL
(Input correct CAL PWD)
【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

Input 6-digit for password value and each “*” stands for one number.
VAL Number
The first 6 digits are defaulted if over 6 digits are input.

Push 【Input】 key after inputting the CAL PWD. If it is correct, then Input the next step. Otherwise, there shall be fault
reported and it needs to be input again. If three mistakes are made, the indicator will return to the previous menu.
Push 【←】 key and the indicator directly return to the previous menu.

CAL PWD Change 【123】

VAL
(Input new CAL PWD)
【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

VAL Number Input 6-digit for password value and each “*” stands for one number.

３６
 XK3190－D18 Menu Operation

The first 6 digits will be defaulted if over 6 digits are input.

Push 【Input】 key after inputting new CAL PWD,

CAL PWD Change 【123】
VAL
(Re-input the new CAL PWD)
【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

Input 6-digits for password value and each “*” stands for one number.
VAL Number
The first 6 digits are defaulted if over 6 digits are input.
Input the new password again. If the new password input between two times is consistent, then the indicator shall
update the CAL PWD and then return back to the previous menu. Otherwise, revision of CAL PWD shall not be
allowed and the indicator will directly returns to the previous menu. Push 【←】 key for going back to the previous
menu.

(14) Time PWD Change

Push 【↑】【↓】 keys to select 『Time PWD Change』and push 【Input】 key.

CAL PWD 【123】

VAL:
(Input correct CAL PWD)
【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

Input 6-digit for password value and each “*” stands for one number.
VAL Number
The first 6 digits are defaulted if over 6 digits are input.
Push 【Input】 key after inputting the CAL PWD. If it is correct, then Input the next step. Otherwise, there shall be
fault reported and it needs to be input again. If three mistakes are made, the indicator shall be back to the previous
menu. Push 【←】 key and the indicator directly return to the previous menu.

Time PWD Change 【123】

VAL: 99/99/99

３７
 XK3190－D18 Menu Operation

(Input timing power-off date)

【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

Input 6-digit date value and display it while shifting towards left, with 2 digits
respectively for year, month and day.
VAL Number For example: if the date is November 17, 2006, then input “061117”.
When the input value is “999999”, timing power-off function is cancelled
automatically.
After inputting for timing power-off date with number keys, push 【Input】 key to save while push 【←】 key for
going back to the previous menu.

(15) Company Name

Push 【↑】【↓】 keys to select 『Company Name』and push 【Input】 key.
Company Name 【123】
VAL: Shanghai Yaohua Weighing Company
(Input the company name)
【←】 Back 【Input】 Confirm

Input Area Input mode Remarks

VAL Number/English Sign 23 characters can be input at most.
Input the company name and print it on the weighig list. Mixed input with English, number and sign is allowed. 23
characters can be input at most. Push 【Input】 key to save after inputting.

(16) Inner Code

Push 【↑】
【↓】 keys to select 『Inner Code of Indicator』and push 【Input】 key. The indicator displays the
current inner code.
VEH CGO. 12:42:56

250000
Inner Code Stable
Push 【Weighing】 key and then the indicator is back to the weighing interface.

(17) System Test

Push 【↑】【↓】 keys to select 【System Test】and push 【Input】 key. The indicator displays:
Micpri Test

３８
 XK3190－D18 Menu Operation

Software
【↑】 Option【Input】 Confirm

1) Micropri Test
Push 【↑】
【↓】 keys to select 【Micropri Test】 and push 【Input】 key. If there is fault for the micro-print, the
indicator displays fault prompt.

2) Software
Push 【↑】
【↓】 keys to select 【Micropri Test】and push 【Input】 key. The indicator displays:

Software
VER 1.00
2008.01.01
【←】 Back
8. Check Record Setup
Under weighing interface, push 【Check】 to Input check record interface.
REC Search Scan Record
VEH. Search All Records DEL
CGO. Search Overload RECs DEL
Overload REC 【↑】 Option 【Input】 Confirm
See the Chapter “Print and Record Processing” for detailed operation.

３９
 XK3190－D18 Input mode
Chapter 5 Input mode
I. Profile of Input mode
This indicator adopts the input mode with number/English/Sign mixed. The operational way is similar to that of T9
input mode which is popular among mobile phones at present.

II. Operation of Input mode

When inputting the parameters of 【VEH No.】, 【CGO No.】, and 【Company Name】, the input mode with number,
English and Sign mixed can be used, while just number can be input for other parameters. When the mixed input
mode is allowed, push 【Input mode】 key to switch the status. Push 【Clear】 key to clear the input characters one
by one.

Display in the upper

Input mode Status
right corner of the screen
【123】 Input Status of Number
【ABC】 Input Status of Capital English
【abc】 Input Status of Minuscule English
【.?!】 Sign Input Status

(1) Input Status of Number

Input the number according to the corresponding number on the keyboard.
(2) Input Status of Capital/Minuscule English
First push 【Input mode】to switch into capital/minuscule English input status and then push the corresponding
keys of the letters. (For example, if letter C should be input, push 【Number 1/ABC】 key.)
1) Constantly push the same character key within 1 second, the input character shall be switched among the
character groups corresponding with this key.
For example, constantly push 【1/ABC】 key within one second, then the input character shall be switched among
A, B and C. Finally, one character is input.
2) Push the character key for over 1 second, the first character corresponding with this key shall be input. If
other characters are required to input, repeat the operation in the above 1), i.e, push the character key
within 1 second corresponding with the letter.
For example, if you want to input “hai”, constantly push 【3/GHI】 key twice for input of letter “h” (the interval
shall be less than 1 second), push 【1/ABC】 key in one minute for once input of letter “a”, and then push
【3/GHI】 for three times input of letter “i” in one minute (the interval shall be less than 1 second). Then the input
can be finished.
(3) Input Status of Sign
 XK3190－D18 Input mode
First push 【Input mode】to switch into sign input status.
1) All the optional signs are displayed in the screen below. After pushing 【←】【→】 keys to select the
required sign, the chosen sign highlighted. Push 【Input】 key and the indicator shall list the chosen sign in
the input area and then automatically switches into Pinyin input status to wait for the next character input.
2) If you want to continue to input sign, push 【Input mode】 key to switch into the sign input status and
then select the optional sign. After input, push 【Input】 key to save it.

For example, if you want to input “?”, push 【Input mode】to switch into sign input status. There shall be a series of
signs displayed in the screen below. Push 【→】 for five times to select “?”, and push 【Input】 key to list the “?”
in the input area. Meanwhile, the input mode is back to Pinyin Input status

４１
 XK3190－D18 Calibration
Chapter 6 Calibration
I. Calibration setup
First open the lead seal, toggle the calibration switch inside to enable it to allow calibration. In weighing mode,
press 【Calibration】and the indicator will show as follows:

CAL PWD 【123】

VAL:
Input right calibrate PWD
【←】Back 【Input】Confirm

Input area Input Instructions

mode
VAL number Input a 6- digit password. Each“*”stands for one digit
The first 6 digits are defaulted if more than 6 digits are input. The
default password is “888888”

After inputting the valid password, press 【Input】 to Input the calibration setup interface. If password is invalid,
error report will appear to require another input. After three incorrect inputting, the indicator will return to weighing
interface. Press 【←】to directly return to weighing interface.
Calibration setup interface is as follows:
Calibration Manu Zero Set upon Initialization
Zero track speed Filter degree
Zero track range Unit
Manu Zero Set 【↑】Select 【Input】confirm
On the calibration setup interface, press 【↑】【↓】for video reversed bar to select 『Calibration』. Press 【Input】
to Input the setting process interface of calibration.
First appears the division value setting,
Division 【123】
VAL：1
(1,2,5,10,20,50 select)
【←】 Back 【Input】Confirm

Input area Input mode Instructions

VAL Number For division value, only 1，2，5，10，20，50 can be input. Error report
will receive if other numbers are input.
 XK3190－D18 Calibration
After inputting division value, press 【Input】 to set decimal points.

Decimal point 【123】

VAL: 3
(Input: 0,1,2,3,4)
【←】Back 【Input】Confirm

Input area Input mode Instructions

VAL Number For scaling position, only 0，1，2，3，4 can be input. Error report will
receive if other numbers are input.
After setting decimal point, press 【Input】 for full scale setting
F.S. 【123】
VAL: 3.000 kg
(Input F.S. value)
【←】Back 【Input】Confirm

Input area Input mode Instructions

VAL Number At most 6 digits are accepted

After inputting F.S value, press 【Input】 for zero point confirmation

VEH. CGO 14:31:48

1569
Calibration AD code Stable Zero point

Wait for ad code to stabilize in idling stage under no load statue. Press 【Input】, and the indicator will Input the load
confirmation stage.
VEH. CGO 14:31:48
298568
Calibration AD code Stable Zero point

To load standard weight, wait for AD code to stabilize, then press 【Input】to Input the interface for load value setup
interface (if AD code jumps slightly, it can be considered stabilized)
Loading 【123】
VAL: 3.000 kg
(Input loading value)
【←】Back 【Input】Confirm

４３
 XK3190－D18 Calibration

Input area Input mode Instructions

VAL Number At most 6 digits are accepted
After inputting loading value, press 【Input】 key to finish calibration. The indicator indicates “Calibration End”
and returns to weighing mode.

Generally speaking, calibration can be completed with the above-mentioned steps. The default values upon delivery
from the factory can be adopted for other measuring parameters. To meet some special requirements, the operating
procedures of the chapter Menu Setup can be followed to do the corresponding setting for the related parameters.

４４
 XK3190－D18 Communications
Chapter 7 Communication
I. Serial communication interface
Notes：
1． The connection of the output lead of communication interface with the computer must be
correct. Or otherwise, the output terminal of indicator and the communication input terminal
of computer will be damaged, even causing , severe damage of indicators, computer and
corresponding peripheral equipments.
2． Computer communication requires certain computer skill and programming ability of the
operator, who must be accompanied or led by some professional technicians.
Non-professionals are not supposed to connect without authorization.
Xk3190－d18 type weighing indicator can realize data communication with upper computer through Comm Setup
Two communication manners are selectable: continuous mode and instruction mode. In the instruction manner, one
upper computer can work with multiple indicators. （rs422/rs485）
1． Comm Method
(1) Communication interface of this indicator adopts a D-sub 15 pin socket. Signals of each pin are shown as 6-, 7-,
8-pin （rs232）, or 1-, 2-, 3-, 4-, 8-pin （rs422/rs485）
，in Fig.（7-1）. Serial communication and scoreboard display
share one socket.

This only applies to Yaohua Communication Interface Protocol. For any special
requirements, users can make connection according to the leading wire definition.

Display output of scoreboard

Fig. (7-1) Serial communication and scoreboard display output interface signal
(2) For connecting wire, 4-pin shielded cable is recommended, whose shield layer should be grounded at the host
computer side.
2． Interface signal parameters
(1) Signal: rs232/rs422/rs485 rs232/rs422/rs485 signal
(2) Baud rate: 600/1200/2400/4800/9600 is selectable for setting
(3) Address range: 26 locations（a～z）

3. Continuous transmission manner of serial communication

 XK3190－D18 Communications68

The data transmitted are the weighing result displayed on the indicator of the current load (gross weight or net
weight). Each frame contains 12 groups of data in the following form:
x-th byte Content and explanation

1 02 (xon) begin
2 +or- Sign bit
3 Weighing value High-Command bit
x-th byte content and explanation
： Weighing data

： Weighing data

8 Weighing data low-Command position

9 Decimal digits from right to left（0～4）
10 XOR Calibration high 4-digit
11 XOR Calibration low 4-digit
12 03 (x0ff) end
xor＝2⊕3⊕　……8⊕9
4． Command mode of serial communication
The indicator outputs corresponding data as per the command of upper computer. Every time when the upper
computer gives out an instruction, the indicator should output 1 frame of data.
Commands from upper computer
n-th group Content and explanation
1 02（xon） Begin
2 A～z Location code
A～i Command a: handshake
Command b: read gross
Command c: read tare
Command d: read net
3 Command e: access VEH No.
Command f: access CGO No.
Command g: Delete All
Command h: set to zero
Command i; tare

4 XOR Calibration high 4-digit

5 XOR Calibration Low 4-digit

6 03（xoff） end

Output content of indicator:

４６
 XK3190－D18 Communications68

x-th group Content and explanation

1 02（xon） Begin
2 A～z Location number
3 A～i Command a：handshake
Command b：transmit gross weight
Command c：transmit tare
Command d：transmit net weight
Command e：transmit VEH No..
Command f：transmit CGO No...
Command g: no data
Command h：no data
Command i：no data
4 Output corresponding data as per the command content

x-th group Content and explanation

5 Output corresponding data as per the command content
6 Output corresponding data as per the command content
7 Output corresponding data as per the command content
8 Output corresponding data as per the command content
Output corresponding data as per the command content
Output corresponding data as per the command content
N-1 Output corresponding data as per the command content
N Output corresponding data as per the command content
N+1 XOR Calibration high 4-digit

N+2 XOR Calibration low 4-digit

N+3 03（xoff） End

The content of 4～n are as follows when the indicator is outputting data:
Command a no data Each frame consists of 6 groups of data
Command b as gross weight form： Each frame consists of 14 groups of data
4： sign（＋or－）
5～11： gross weight value（6 digits and
one decimal digit）
Command c as tare， form： Each frame consists of 14 groups of data
4： sign（＋or－）
４７
 XK3190－D18 Communications68

5～11： tare value（6 digits and one

decimal digit）
Command d as net weight form： Each frame consists of 14 groups of data

4： sign（＋or－）

5～11： net weight value（6 digits and one

decimal digit）
Commandｅ VEH No.. form： Altogether 16 characters are transmitted. Chinese

４～13: 10 characters characters are allowed (one Chinese ideograph takes

space of two characters). When VEH No. Is shorter
than 10 characters, use space to fulfill.
Commandｆ CGO No.. form： Altogether 16 characters are transmitted. Chinese

４～13: 10 characters characters are allowed (one Chinese ideograph takes

space of two characters). When CGO No. Is shorter
than 10 characters, use space to fulfill.
xor＝2⊕3⊕……10⊕11
Note: definition of XOR Calibration of high & low 4 digits:
1. If the XOR Calibration sum of high & low 4 digits are less than or equal to 9, then it is transmitted as ascii
code number after adding add 30h.
For example: if the high 4 digit of XOR Calibration is 6, 36h is obtained after adding 30h, i.e., 6 in ascii code
is then transmitted.
2. If the XOR Calibration sum of high & low 4 digits is more than 9, then it is transmitted as ascii code number
after adding 37h. .
For example: the high 4 digit of XOR Calibration is b, 42h is obtained after adding 37h, i.e. b in ascii code is
then transmitted.
II. Connection and usage of scoreboard with indicator

The connection of the output lead of large screen with the display must be correct. Or
otherwise, the output terminal of indicator and the input port of display of large screen will be
damaged, even causing severe damage of indicators, display of large screen. Self-contained
exclusive wires are required for the connecting.

1． Scoreboard display interface adopts 15-pin D-sub socket (share one socket with serial communication
interface). Functions of its pins are shown as 9-, 10-pin in Fig. (7-1). (This is an output manner of current loop, a
standard connection manner of wires on departure from factory)
2 . Scoreboard signal is current loop, serial output by binary code, with baud rate of 600. Each frame has 11 bits, 1
４８
 XK3190－D18 Communications68

start bit (0), 8 data bits (low bits come first), 1 flag bit, and 1 stop bit (1).
3. One group of data is transmitted per 100ms. Each group contains 3 frames. See Fig (7-2) for its meaning.

Fig. (7-2) Oscillogram of data format

The first frame: the flag bit is 0
x : d0, d1, d2 –are decimal bits ( 0～4 )
y : d3 — is weight sign ( 1－negative, 0－positive )
d4 —spare
G: 18～g16：weight data
The second frame: the flag bit is 0
G:15～g8：are weight data
The third frame: the flag bit is 1
G:7～g0 ：are weight data
G0～g18： from low to high to form the 19-bit binary code for the (net) weight
４９
 XK3190－D18 Print and Record processing
Chapter 8 Print and Record Processing

I. Connection of the indicator with printer

The printer interface adopts standard parallel output. Socket connector uses 25-pin rs232 socket. Definition of each pin
is as follows in Fig.（8-1）

(Fig.8-1) Interface signal of printer

Notes for printing:
1． Printing function comes into normal use only after setting.
2． The connection of the printer output lead of the indicator with the printer must be correct. Self-contained
exclusive wires are required for the connecting. Or else wrong connection will injure the indicator output port
and input port of the printer, even severely damage the indicator and the printer.
3．To use the printer, the wires must be connected before the indicator is powered on. Then the printer can be
turned on. After the use of printer, turn off the printer first, then cut off the indicator power, finally take off
the connecting wires. If theses procedures are performed in a wrong order, the indicator and printer can
possibly be damaged. Please pay attention!
4．The printers have large variety, with different properties. Some are incompatible with the indicator. So
please select the recommended printer.
5．The grounding of printer signal is forbidden to connect with that of power supply. This will cause damage to both
the indicator and printer

II. Storing and printing of the weighing records

1． The indicator specifies 10 characters both for VEH No. and CGO No. (1 Chinese ideograph takes space of two
characters). At most 1000 VEH No and CGO No. can be stored.
2． Each group of data is printed out every time when a complete group of records is stored. (if the printer is set valid)
3. There are three manners of data storage:
(1) No load data storage before full load data, or full load data before no load data. That’s to say, such two data are
required to form a set of record.
(2) When tare is known for a full load truck, one storage operation will make a complete record.
(3) If the weighed material is goods instead of the loaded truck, one storage operations will make a complete record
 XK3190－D18 Print and Record Processing

To distinguish three storage methods, XK3190－D18 stipulates as follows:

1． License code zero means the goods to be weighed; no tare is required, which is permanently set to be 0. The
VEH No. can not be cleard either. During displaying and in printing, it reads “----------”.
2． If the tare sign is on, it means the tare is known, so one storage operation will make a complete record.
3． If the License code isn’t 0, nor the current tare is 0, two storing operations are required to make one complete
record.

4. Operation manner of storing and printing

I& n the weighing state, press 【Save Print】, and the indicator displays the following,
Print Information 【123】
VEH: A12345 Code: 1
CGO: --- Code: 1
【←】Back 【Input】Confirm
Press 【Input】 after inputting the VEH No..
Print information 【123】
VEH: A12345 Code: 1
CGO: --- Code: 1
【←】Back 【Input】Confirm
The code is generated automatically as per the VEH No. If VEH No. is not put previously, input code hereby, then press
【Input】 key
Print information 【123】
VEH: A12345 Code: 1
CGO: --- Code: 1
【←】Back 【Input】Confirm
Press 【Input】 key after inputting CGO No..
Print Information 【123】
VEH: A12345 Code: 1
CGO: --- Code: 1
【←】Back 【Input】Confirm
The code is generated automatically as per the VEH No... If CGO No. is not input previously, input code hereby, then
press 【Input】 key.
The indicator executes storage and printing operation

５１
 XK3190－D18 Print and Record Processing
Input area Input mode Instructions
VEH No. number/ English/sign at most 10 characters are to be input
Code (upper) number at most 3 digits are to be input
CGO No. number/English/sign at most 10 characters are to be input
Code (lower) number at most 3 digits are to be input

Notes:
(1) When there is reverse video in the input area, it means value can be input hereby. Select any from VEH No./CGO
No. and code area to fill
（2）If VEH No /CGO No. area is chosen for the input value; the indicator will retrieve the memory automatically after
【Input】 key is pressed, to see if there is any corresponding code. If so, the code is shown, if not, new code is generated
automatically and displayed. If the corresponding code of VEH No./CGO No. is known before hand, input the code
directly into the code area and the indicator will retrieve automatically the corresponding VEH No./CGO No. and they
are displayed. By this way, the relative complicate operations can be avoided. The VEH No./CGO No. can be input with
Chinese, English and numbers mixed. Press 【Input mode】 to switch over the input modes. After completion of
switchover between the four input areas, press【Input】 to save the VAL and execute printing operation. Printing is
canceled and return to the weighing interface if 【←】is pressed.
（3）The data storage adopts two manners, with or without VEH No. . (See the chapter Menu Operation for detailed
setting). If VEH No. is not used for setting, the license code is fixed as 0 and unchangeable.

（4）The data storage adopts two manners, with or without CGO No. (See the chapter Menu Operation for detailed
setting). If CGO No. is not used for setting, the item code is fixed as 0 and unchangeable.
（5）When the data is unstable or either the gross weight or the net weight is less than or equal to 0, records can not be
stored.

5. About auto save and print

(1) The setting of automatic storage and printing is described in the chapter Menu Operation.
(2) There isn’t twice-storage manner for automatic auto save and print.
(3) VEH No./CGO No. in the automatic storage is the VEH No./CGO No. already set before the storage.
(4) Tare value for automatic storage is classified into 3 situations:
① When the net weight sign is on , the current weighed tare value is stored in the group of records
②When the net weight sign is not on, the indicator searches the tare of this VEH No. in the memory, and stores it
into the group of records
③When the net weight sign is not on, and there is no tare of corresponding to the VEH No. in the memory, 0 is
stored as tare value into the group of records.
6. When there are more than 1000 VEH No., a certain VEH No. or all of the records are to be cleard in a manner
introduced in next paragraph. If there are more than 1000 groups of weighing records, the indicator will clear the
５２
 XK3190－D18 Print and Record Processing
earliest record to make room for the current weighing result.
III. An example for print operation
1． Print the weighing sheet with tare manually preset for one time
Proced Situation Operations Display Instructions
ures s
1 item press 【preset tare】 setup
loaded interface of
preset tare
2 input the E.g. 1000 VAL: 1.000
preset kg
tare
3 press【Input】 Save the VAL. The preset tare comes into effect
4 press 【←】 Return to weighing interface
5 press【Save Print】 Interface of
inputting
VEH No. &
CGO No.
6 input e.g.: aa1245, press 【Input】to VEH No.: If the previous VEH No. is required, directly press
VEH No. save aa1245 【Input】 without changing VEH No.
7 press 【Input】 Input code area.
8 1． If no VEH No. Is input, the code: 1 1. If the VEH No. has been input already, the code
Input code must be input. will be automatically generated. Press 【Input】 to
VEH No. 2． If the VEH No. has been skip directly.
input, input nothing here. 2. If no VEH No. is input, input the code here.
9 press 【Input】 Input the item setting
10 Input E.g.: rolled steel. Press 【Input】 CGO No.: if the previous CGO No. Is wanted here , directly
CGO No. to save. rolled steel. press 【Input】 to reserve and the CGO No.
Needn’t any change.
11 press 【Input】 Input code region
12 Input 1．If no CGO No. is input, here Code: 0 1. If the CGO No. has been input already, the code
item code must be input. will be automatically generated. Press 【Input】 to
Code. 2． If CGO No. is already, input skip directly.
nothing here. 2. If no CGO No. is input, input the code here
13 press 【Input】 Save the code. Begin the printing and weighing

2． Direct manual printing of the weighing sheet for one time

５３
 XK3190－D18 Print and Record Processing
Proced Situations Operations Display Instructions
ures
1 press 【Save Print】 interface of Press keys in the weighing interface
inputting VEH
No./ CGO No.
2 press 【Input】 No need to input VEH No. Directly press
【Input】 to Input code area.
3 “0” input input 0 code: 0 License code 0 means item weighing
VEH. No. permanently, which cannot be cleard
code 0
4 press 【Input】 Save the code and Input the setting of CGO
No.
5 input CGO E.g.. rolled steel. Press CGO No.: rolled If the previous CGO No. is required, directly
No. 【Input】 to save steel. press 【Input】without changing the CGO
No.
6 Press 【Input】 Input code area
7 input CGO 1. If no CGO No. is code: 0 1．If CGO No. is already input, code will be
Code input, input code here. produced automatically. Press 【Input】 to
2. If CGO No. is already skip.
input previously, it is not
2． If no CGO No. is input yet, input the
required to input here
code here.
8 Press 【Input】 Save the code to begin to print the weighing
sheet.

3． Print the weighing sheet (two times storage mode, first empty load then full load, or first full load then empty
load)
Procedures Situations Operations Display Instructions
1 Empty truck is loaded press 【Save Print】 Interface of inputting Press keys on the weighing interface.
(wait until the sign VEH No. & CGO No.
stabilize)
2 input new VEH No. e.g. ： aa1245, VEH No.: aa1245 If the previous VEH No. is required,

press 【Input】to directly press 【 Input 】 without

save changing the VEH No..

3 press 【Input】 Input code area
4 input license code 1. If no VEH No. code: 1 1. If the VEH No. has been input
is input, input code already, the code will be automatically
here. If VEH No. generated. Press 【 Input 】 to skip

５４
 XK3190－D18 Print and Record Processing
is already input directly.
previously, no 2. If no VEH No. is input, input the
need to input it code here.
here
5 press 【Input】 Save the code and Input the setting of
items no.
6 input CGO No. E.g. rolled steel. CGO no.: rolled steel. If the previous CGO No. is required,
Press 【Input】to directly press 【 Input 】 , without
save changing the CGO No...
7 press 【Input】 Input code area
8 input CGO No.. Code 1． if no CGO No.. code: 1 1． if CGO No. is already input, code
Is input already, will be produced automatically. Press
input code here. 【Input】 to skip.
2． if CGO No. is 2． If no CGO No. is input yet, input
already input the code here.
previously,.
Needless to input
anything here
Procedures Situations Operations Display Instructions
9 Press【Input】 Record incomplete, not Save the code and return to the
print right now! weighing interface
10 heavy truck is loaded Press【Save Print】 interface of inputting Display the VEH No. and CGO No.
(wait until the VEH No. / CGO No. previously input
stabilize sign on)
11 VEH No. inputting press【Input】 no need to input anything
state
12 VEH No. inputting press【Input】 no need to input anything
state
13 VEH No. inputting press【Input】 no need to input anything
state
14 CGO No.. inputting press【Input】 Printing… no need to input anything. Press
state 【Input】key to print out weighing
sheet

Attention: if heavy load is weighed for the first time, the empty load should be weighed next time. Other operations are
similar.
4． Automatic printing of the weighing sheet with tare preset
５５
 XK3190－D18 Print and Record Processing
Procedures Situations Operations Display Instructions
Set 『 printing method 』 as “automatic
printing” according to the requirements of
1
chapter Menu Operations , and press
【Weigh】to return to weighing interface
2 input the preset tare E.g.: 100 VAL: 100 kg
Save the VAL. The preset tare comes into
3 press【Input】
effect
4 Press【←】 Return to weighing interface
heavy truck is
loaded (wait until Heavy load is 500, with tare 100 to be
5 The weight reads 400 kg
the stabilizing sign reduced
on)
Print automatically the weighing sheet
6 Printing
when the weight display stabilizes
5． Print the weighing sheet while calling the tare as per VEH No.
Proc Situations Operations Display Instructions
edur
es
1 Tare of the VEH No. Already stored in the indicator
has been preset
2 Heavy truck is setting interface of VEH Display the previous license and
loaded (wait until Press 【VEH No.】 No. and tare tare
the stabilize sign on)
3 Input the required E.g. aa00123 VEH No.: aa00123 If consistent with the previous VEH
VEH No. press 【Input】to save No., directly press 【Tare】. There
is no need to input VEH No.
4 press【Input】 Input the setting of license code.
5 input the required press【Input】 1． If the license has been input,
VEH No. directly press 【 Input 】 without
inputting anything.
2． If no VEH No. is input
previously, input the VEH No. and
press 【Input】 to save
6 press 【Tare】 return to the weighing The value after deducting the saved
interface and display the tare

５６
 XK3190－D18 Print and Record Processing
net weight value. Net
weighing sign shines
7 Press 【Save Print】 interface of inputting press key under weighing interface
VEH No./CGO No.
Procedures Situations Operations Display Instructions
8 input new VEH No. E.g. aa1245 VEH No.: aa1245 If the previous VEH No. is
press 【Input】 required, directly press 【Input】
to save without changing the VEH No..
9 press【Input】 Input code area
10 input license code 1. If no VEH code: ** 1. If VEH No. is already input,
No. is input code will be produced
already, input automatically. Press 【Input】 to
code here. skip.
2． If VEH No. 2. If no VEH No. is input yet, input
is already input the code here.
previously, no
need to input
anything here
11 press【Input】 Save the code and Input the setting
of CGO No.
12 input CGO No. e.g.: rolled steel CGO No.: rolled steel. If the previous CGO No. is
press 【Input】 required , directly press 【Input】
to save without any need to change the
CGO No.
13 press【Input】 Input code area
14 input item code 1. If no CGO code: 0 VEH No.
No. is input,
input code here.
2． If CGO No.
is already input
previously, no
need to input
anything here
15 press【Input】 Print the weighing sheet
16 Return to weighing state

6． Print the weighing sheet manually with varied truck tares preset
５７
 XK3190－D18 Print and Record Processing
Procedures Situations Operations Display Instructions
1 press 【VEH No.】 interface of Press keys on the weighing interface
setting VEH
No. / tare
2 Input new VEH E.g. aa00123, press If the existing VEH No. is required,
No. 【Input】to save press 【Input】 without transmitting
new VEH No..
3 press【Input】 Input code area
4 press【Input】 Code is automatically generated
according to the previously input
VEH No. No need to set it here. Press
【Input】to Input the tare input area
5 transmit the preset e.g.: 100, Tare:
tare Press 【Input】to save 100 kg
6 Store preset tare 1. Press【Input】to input
for varied truck new VEH No. cyclically
and input the setting of
next vehicle
2. If VEH No./tare are all
input, press 【 ← 】 to
return to weighing.
interface

Procedures Situations Operations Display Instructions

7 Continue the operations
as per above table
“Print the weighing
sheet while calling the
tare as per VEH No.”
7． Periodic printing of reports (three copies)
Proced
Operations Display Instructions
ures Situations
1 press 【Report Print】 on the weighing interface
2 press【Input】 select the report by time
3 press number keys to input starting date input the starting date of the printed

５８
 XK3190－D18 Print and Record Processing
record
press number keys to input finishing input the finishing date of the
date printed record
4 press【Input】 print the related three reports

8． Print general report

Procedure
Situations Operations Display Instructions
s
1 press 【Report Print】 Report Type in weighing mode
2 press 【↓】 select Report 1
3 press【Input】 Report Print 1
press 【↓】 to select other types
4 Report 2～6 print out the reports respectively
for the second step
Note: See appendix for the style of report by time form and report form
IV. Enquiry of the weighing record
Press【check】in the weighing interface to Input record-checking interface
Record Search Scan Record
VEH No. Search Delete All
CGO No. Search Delete Overload
Overload REC 【↑】select 【Input】Confirm
Press【↑】【↓】 keys to select the check mode. Press 【←】to return to the weighing interface

VAL Instructions
Record Search scan the weighing record as per record time
VEH No... Search scan the weighing record as per the recorded VEH No.
CGO No. Search scan the weighing record as per the recorded CGO No.
Overload REC scan the past Overload REC
Scan Record scan all the weighing record
Delete All scan the valid CGO No. reserved
Delete Overload scan the past Overload REC

（1）Scan Record
press 【↑】【↓】 keys to select the manner of scan record. Press【Input】

５９
 XK3190－D18 Print and Record Processing
Scan Record 【123】
From 06/04/12 to 06/04/12
VEH: 555 Code: 0
CGO: 1111 Code: 1

Input area Input mode Instructions

Input 6-digit date value. Shift left to display. Two digits respectively for year,
Starting from
number month and date.
to
For example: for the date Nov17, 2006, “061117” is to be input.
VEH No. English sign 10 characters are to be input
CGO No. English sign 10 characters are to be input

Press【Input】after inputting the date

0001/0020 06/04/12 12：32 ：30

VEH: A12345 CGO: high-quality rolled steel Gross: 2000 kg tare: 50 kg
Net: 1950 kg 【↓】Turn pages

Press【↑】【↓】 keys to turn pages and scan the record

0002/0020 06/04/12 12：40 ：30
VEH: A12345 CGO: high-quality rolled steel Gross: 2050 kg tare: 50 kg
Net: 2000 kg 【↓】Turn pages

Under Scan Record status, press 【Clear】to clear this record.

（2 ）VEH No. Search
Press【↑】【↓】 keys to select VEH No. and press【Input】
0001/0009
VEH: AA13355 Code: 001 Tare: 0.000 kg
【←】Back 【↓】Turn pages
Press【↑】【↓】 keys to turn pages and scan record. Press 【←】to return previous menu
（3）CGO No. Search
Press【↑】【↓】 keys to select CGO No. Then press【Input】
0001/0004
CGO: Rolled steel Code: 001
【←】Back 【↓】Turn pages
Press【↑】【↓】 keys to turn pages and scan record. Press 【←】to return to previous menu
６０
 XK3190－D18 Print and Record Processing
（4）Overload REC
Press【↑】【↓】 keys to select the Overload REC and press【Input】
0001/0002
Date: 06/11/13 Time：15：26：48
Gross: 223.394 kg
【←】Back【↓】Turn pages
Press【↑】【↓】 keys to turn pages and scan record. Press 【←】to return to previous menu
（5）Scan Record
Press 【↑】【↓】 keys to select the 『Scan Record』manner, press【Input】
0001/0020 06/04/12 12：40 ：30
VEH: A12345 CGO: high-quality rolled steel Gross: 2050 kg Tare: 50 kg
Net: 2000 kg 【↓】Turn pages

Press【↑】
【↓】 keys to turn pages and scan record.

0002/0020 06/04/12 12：45 ：30

VEH: A12345 CGO: high-quality rolled steel Gross: 2050 kg Tare: 50 kg
Net: 2000 kg 【↓】Turn pages

Under scan record. status, press 【Clear】to delete this record.

(6) Delete All

Press 【↑】
【↓】 keys to select 『Delete All』. Press【Input】to Input the confirmation prompt for deletion.
Press【Input】to clear all the records. Press【←】to return to the previous menu.

Delete All?
【←】 Back 【Input】Confirm
(7) Overload DEL
Press 【↑】
【↓】 keys to select 『Overload DEL』. Press 【Input】to Input the confirmation prompt for deletion.
Press【Input】to delete all the overloads. Press【←】to return to the previous menu. Overload DEL requires the correct
input of CAL PWD

６１
 XK3190－D18 Info prompts
Chapter 9 Info prompts
No. Indicator prompts Explanation Solutions
Record the confirmation operation
Select whether to clear according to
1 Time REC DEL? before deletion to prevent any wrong
the prompts
deletion.
Record the confirmation operation
Select whether to clear according to
2 VEH No. Rec DEL? before deletion to prevent any wrong
the prompts
deletion.
Record the confirmation operation
Select whether to clear according to
3 CGO No. Rec DEL ? before deletion to prevent any wrong
the prompts
deletion.
4 No CGO No. Rec.! Prompt of no corresponding record
5 No VEH No. Rec.! Prompt of no corresponding record
6 No Eligible Rec. Prompt of no corresponding record
7 No Overload REC Prompt of no corresponding record
Prompt of deletion process by
8 REC DEL! Wait! Wait for the completion of deletion
indicator
It’s time to turn off. The indicator is Re-input the timing power-off time as
9 Time power-off!
locked per the set password
10 Overload! the indicator is overloaded Unload the whole or partial weight
11 Printing...
Follow the standard Save Printing
specifications
●Not print when unsteady

●Resetting to zero is not made after

12 Not meet print!
previous printing. The indicator must
be reset to zero.
●Not print when the weight is below

zero
13 Not complete! Second weighing is needed
Parameter save by EEPROM is For delivered indicators, maybe
14 EEPROM ERROR! wrong, possibly due to the first use of EEPROM is damaged. A new chip is
indicator or damage of EEPROM required.
Printer not connected or damaged; or Check the connection of printer and
15 Printer error! printer model not compatible with the indicator, or change for a compatible
indicator printer.
16 Upgraded Prompt that data is saved
 XK3190－D18 Info prompts
Input data correctly as per the prompt
17 Invalid The inputed data is beyond the range
of the indicator parameter range
1. All or part of the records need
deleting to make room for later
18 Records full Memory of weighing records is full
records
2. Memory needs initializing
19 No record No weighing record in the memory
20 Deleted Prompt of records deletion

６３
 XK3190－D18 Maintenance & Notes
Chapter 10 Maintenance & Notes
I. To ensure the clarity and service life of the indicator, it must be kept away from direct sunlight during using,
and the ground where the indicator stands must be smooth.
II. It is improper to use this indicator in a dustful or vibrant or damp environment.
III. The load cell and indicator need good connection. System must have a good ground connection, and kept away
from strong electric field, strong magnetic field. The load cell and indicator must be kept away from strong corrosive
substances and inflammable& explosive materials.
▲！ Do not use it where inflammable gases or steams exist. Don’t use it for canning system of compressive
container.
▲！ In the area where lightning and thunder happen frequently, reliable lightning arrester should be installed
to ensure the personal safety and to prevent any damage to the indicator and relative equipment caused by
lightning stroke.
▲！The load cell and indicator are both static sensitive equipments, so anti-static measures must be taken
during the use. It is strictly invalid to carry out welding operation or other operations with high current on the
weighing platform. In the stormy season, lightening prevention measures must be taken reliably to prevent any
damage to load cell and indicator caused by lightening stroke, and to guarantee the personal security of
operators and safe running of weighing devices and relative equipments.
IV. Strong solvents such as benzyl and nitro oils are forbidden for cleaning the housing
V. Don’t inject any liquid or other conductive particles so as to avoid any damage of indicator and electric shock
VI. Before plugging in or out of the connecting line between indicator and external equipment, the power of both
indicator and equipment should be cut off
▲！Before plugging in or out of the connecting line of load cell, the power of indicator should be cut off!
▲！Make sure that the indicator and the printer are powered off before inserting the connection line of
printer.
▲！Make sure that the indicator and the scoreboard are powered off before plugging in or out of the
connection line of the scoreboard!
▲！Make sure that the indicator and the upper computer are powered off before plugging in or out of the
communication connection line.
VII. Advice of the company: our company is responsible for the indicator quality, but not responsible for the
problems of the system where the indicator locates. Your attention is required when making purchase.
VIII. Please use the indicator outward interfaces strictly as per the operating instruction manual. Do not change the
connection at random. If failure occurs in the using process, draw the plug immediately, and send it for professional
factory for reparation. Non professional balance manufacturers are not supposed to do the repairing to avoid any worse
damage. It is not allowed to open the indicator at will, or else, repairing will be refused.
IX. If non artificial defects and failures happen after normal use within one year after the sale date, the users can mail
the product and guarantee repair card ( with correct code) to the appointed reparation station or supplier. The
manufacturer guarantees the life-time maintenance for the indicator
 Appendix
1. Print Format
Report 1 by Time Date: 07/12/20 – 07/12/21
Gross
No Date Time VEH No. CGO No. Tare (kg) Net weight (kg)
weight (kg)
1 07/12/20 11:26:16 AA000001 rolled steel 1000 100 900
2 07/12/20 11:29:16 AA000001 rolled steel 1200 100 1100
3 07/12/20 11:32:16 AA000001 rolled steel 1400 100 1300
Total Gross weight: 3600 kg Net weight: 3300 kg
Note: Records in Report 1 by Time is to be listed in time order
Report 2 by Time Date: 07/12/20 – 07/12/21
No VEH No. Truck weight (kg) Times Grand gross weight (kg) Grand net weight (kg)
1 --------- 0 5 5000 5000
2 AA000001 0 3 3600 3300
3 AB000001 0 4 4000 3600
Note: Records in Report 2 by Time is to be listed in VEH No. order
Report 3 by Time Date: 07/12/20 – 07/12/21
No. CGO No. Time Grand net weight (kg)
1 ------------- 5 4500
2 Rolled steels 3 3300
3 stone 10 5600
Note: Record in Report 3 by Time is to be listed in CGO No. order.
Report 1
No Date Time VEH No. CGO Gross weight (kg) Tare (kg) Net weight
No.
1 06-11-22 11:26:16 ------- ------- 1200 0 1200
2 06-11-22 12:20:17 AA0001 oil 1500 200 1300
3 06-11-25 10:20:15 AB0001 Rolled 5600 600 5000
steel
Total: Gross weight: 8300 kg Net weight: 7500 kg
Note: Records in Report I is to be listed in time order
Report 2
No. VEH No. Truck weight (kg) Times Grand gross weight (kg) Grand net weight (kg)
1 ---------- 0 5 2600 2600
2 AA000001 100 4 5600 5000
3 AB000001 100 4 6600 6100
Note: Record in Report 2 is to be listed in VEH No. order

Report 3
No CGO No. Times ）Grand net weight (kg)
1 ---------- 5 2600
2 rolled steel 4 5000
3 oil 4 6100
Note: Record in Report 3 is to be listed in CGO No. order
Report 4
No. Code VEH No. Truck weight (kg)
1 0 ------------- 0
2 1 AA000001 100
3 2 AB000001 100
Note: Report 4 shows the code and truck weight corresponding with the VEH No.
Report 5
No Code CGO No.
1 0 ----------
2 1 rolled steel
3 2 oil
Note: Report 5 shows the code corresponding with the CGO No.
Report 6
No. Date Time Gross weight (kg)
1 06-11-21 10:14:20 2000
2 06-11-22 10:15:00 5600
3 06-11-23 12:17:30 4000
Note: Report 6 shows the Overload RECs

６６
2. Expandable function instruntion
PS/2 keyboard
Summary
XK3190-D18 indicator can be added PS/2 keyboard interface. For the convenience of users to connect the
indicator to popular key board, PS/2 interface adopts USB-A socket, which functions only as an interface. Insert the
plugof the indicator to the PS/2 keyboard at the back pnel of the indicator, and the PS/2 keyboard is enabled to control
the work of the indicator, Inputing all kinds of parameters.
Operation instructions
The function keys F1~F12, backspace key, cursor direction key of PS/2 keyboard correspond to the function keys
of D18, see the table below for detailed correspondence relation:
Table Correspondence Relation between PS/2 Keyboard and XK3190-D18 Function Keys
Save
XK3190-D18 F1 F2 CGO No. VEH No. Setup Inspection Fill PRT
tare
PS/2 F1 F2 F3 F4 F5 F6 F7 F8
Preset Save Calibratio
XK3190-D18 Report Print Zero Set Sum Print Input Clear
tare Print n
PS/2 F9 F10 F11 F12 PrtScr ScrollLock Input Backspace
Back
XK3190-D18 Input mode Axle Axle All Roll Weighing Select Tare
light
PS/2 Insert Break Home End PgUp PgDn Tab Del
XK3190-D18 ← ↑ → ↓
PS/2 ← ↑ → ↓
In the characters inputting status, the switchover of capitalization is same as that on the computers. When inputting
Chinese characters, they appear in the Pingyin area. And the characters on the keyboard can be Inputed directly.
USB interface
USB interface of XK3190-D18 is a device interface, adopting USB-B socket, available for connection to the upper
computer with the equipped USB cable, and to transmit weighing data and records to the upper computer. The data
transmission format is same as RS-232C interface.
Ethernet interface
XK3190-D18 is an expandable Ethernet interface, with specifications of 10Base-T/100Base-TX. It can be
connected to upper computer via LAN, and to internet by gateway, and transmit weighing data and records to the upper
computer.
DC 6V Power Interface
XK3190-D18 is an expandable DC 6V direct current power interface, and accept 6V storage battery with an input
voltage of 5.5~8V, which is displayed on the equipment. When the battery voltage is low, the running of microprinter is
stopped. When the battery voltage is too low, the equipment powers off automatically.
Expand ABLE interface
On the Main board of XK3190-D18, there are expandable interfaces，through which, 4-20m electric current loop,
CAN interface can be added

６７