Number One In Fluitronic Elevator Components 2 SPEED VICTORY DOORS

2 SPEED VICTORY DOOR

HOME ELEVATOR ENTRANCES
NON FIRE RATED

2 Cochran Drive
Ayr, Ontario, Canada
N0B 1E0

Toll Free: 1-800-567-3557

Technical Support: Ext. 240
Fax: 1-519-624-6575

www.oillift.com
 2 SPEED VICTORY DOORS

Table of Contents
● GENERAL DISCLOSURE....................................................................................................1.00

● DIMENSIONAL DATA...........................................................................................................2.00
2 SPEED DOOR OPERATOR WITH DOORS AND SILL.................................................2.01
2 SPEED LANDING ENTRANCE WITH DOORS AND SILL............................................2.02

● INTERFACE OF DOOR OPERATOR WITH WOOD CAB...................................................3.00

● INTERFACE OF LANDING ENTRANCE WITH HOISTWAY...............................................4.00

● INSTALLATION OF DOOR OPERATOR, CAB SILL AND CAB DOORS.............................5.00

● INSTALLATION OF LANDING ENTRANCE........................................................................6.00

● CONSTRUCTION OF ENTRANCE AFTER ENTRANCES ARE SET..................................7.00

● ELECTRICAL DIAGRAMS OF THE CONTROLLER BOARD..............................................8.00

● SET UP OF THE CONTROL BOARD..................................................................................9.00

● TROUBLE SHOOTING......................................................................................................10.00

This document is for information purposes only. We reserve the right to modify the reported specifications, in any parts,
without notice. The printed drawings are informational only, and there might be differences with the actual product.
 2 SPEED VICTORY DOORS

GENERAL DISCLOSURE
The purpose of this manual is to provide OLS customers with support documentation to aid in the
Interface and installation of 2 Speed Victory Door system.

The topics covered in this manual include:

- Dimensional Data of the Door Operator and Landing Entrance
- Interface of Door Operator, Cab Doors and Cab sill with Cab
- Interface of Landing Entrance with building/hoistway
- Installation of Door Operator and Doors
- Installation of Landing Entrance
- Electrical Interface, Set-up, and Troubleshooting.

We strongly recommend that the interface of Doors to your Cab and Landing Entrance are prototyped
in your own facility. Do not try to prototype in the field!

Please Note:
Door Key and Programming tool have to be ordered separately Do not give door key to home owner
and or any other person. Door Keys should be provided to Licensed Elevator Technicians only!

Any additional information and technical support please contact OLS at 1-800-567-3557.

1.00
 D 235(9 1/4")

100(4")
2 SPEED VICTORY DOORS
D 60(2 3/8")

2 SPEED DOOR OPERATOR

    
    

 
 

CLEAR OPENING


E 900(35 1/2”)
F DOOR
RESTRICTOR



  
 

 
 


C  
 






 



 



 

 
 
 
 


DOOR SILL

 
DR
fe
  CH

A QA

 MF


 AP
 
G 


 
 4 3 



 


*DIMENSION FROM SILL LINE
ALL

DIMENSIONS SHOWN IN mm(in)
   
    
CLEAR OPENING A B C D E F G H
900(35 1/2") X 2000(78 3/4") 2000(78 3/4") 2185(86") 2400(94 1/2") 625 (24 5/8") 1300(51 3/16") 1045(41 1/8") 960(37 3/4") 1350(53 1/8")
900(35 1/2") X 2100(82 5/8") 2100(82 5/8") 2285(90") 2600(102 3/8") 625 (24 5/8") 1300(51 3/16") 1045(41 1/8") 960(37 3/4") 1350(53 1/8")
900(35 1/2") X 2400(94 1/2") 2400(94 1/2") 2585(101 3/4") 2900(114 1/8") 625 (24 5/8") 1300(51 3/16") 1045(41 1/8") 960(37 3/4") 1350(53 1/8")

2.01
 2 SPEED VICTORY DOORS

 2 SPEED LANDING ENTRANCE

   

  CLEAR OPENING

900(35 1/2”) x 2000(78 3/4”)
900(35 1/2”) x 2100(82 5/8”)



900(35 1/2”) x 2400(94 1/2”)

   



  



   











 






ALL DIMENSIONS SHOWN IN mm(in)

    
CLEAR OPENING A B C D E F G H
900(35 1/2") x 2000(78 3/4") 2000(78 3/4") 900(35 1/2") 2225(87 5/8") 1135(44 11/16") 1375(54 1/8") 1140(44 7/8") 960(37 3/4") 1450(57 1/16")
900(35 1/2") x 2100(82 5/8") 2100(82 5/8") 900(35 1/2") 2325(91 1/2") 1135(44 11/16") 1375(54 1/8") 1140(44 7/8") 960(37 3/4") 1450(57 1/16")
900(35 1/2") x 2400(94 1/2") 2400(94 1/2") 900(35 1/2") 2625(103 5/16") 1135(44 11/16") 1375(54 1/8") 1140(44 7/8") 960(37 3/4") 1450(57 1/16")

2.02
 2 SPEED VICTORY DOORS

INTERFACE OF OPERATOR WITH WOOD CAB

INTERFACE SHOWN WITH WOOD CAB. FOR STEEL CAB INTERFACE USE DIMENSIONS SHOWN ONLY















NOTE: 
D= CLEAR OPENING HEIGHT FROM UNDERSIDE OF HEADER TO FINISHED FLOOR (CAB SILL) 
E= TOP OF UNI-STRUT TO FINISHED FLOOR (CAB SILL)

ALL DIMENSIONS SHOWN IN mm(in)
CLEAR OPENING A B C D E
900(35 1/2") X 2000(78 3/4") 461(18 1/8") 439(17 9/32") 900(35 1/2") 2000(78 3/4") 2185(86")

900(35 1/2") X 2100(82 5/8") 461(18 1/8") 439(17 9/32") 900(35 1/2") 2100(82 5/8") 2285(90")
900(35 1/2") X 2400(94 1/2") 461(18 1/8") 439(17 9/32") 900(35 1/2") 2400(94 1/2") 2585(101 3/4")

 3.01


 
  2 SPEED VICTORY DOORS

INTERFACE OF LANDING ENTRANCE

WITH HOISTWAY 


 






 





 
ALL DIMENSIONS SHOWN IN mm(in)
CLEAR OPENING FRAME HEIGHT (A) ROUGH OPENING (B) MINIMUM (C) FRAME WIDTH (D)
900(35 1/2") X 2000(78 3/4") 2225(87 5/8") 2276(89 5/8") 505(19 7/8") 1140(44 7/8")
900(35 1/2") X 2100(82 5/8") 2325(91 1/2") 2375(93 1/2") 505(19 7/8") 1140(44 7/8")
900(35 1/2") X 2400(94 1/2") 2625(103 5/16") 2675(105 5/16") 505(19 7/8") 1140(44 7/8")

4.00
 3 2

2 SPEED VICTORY DOORS

INSTALLATION OF DOOR OPERATOR, CAB SILL

AND CAB DOORS
GUIDE LEGEND:

REQUIRED WORKERS

REQUIRED TOOLS

4 3
CAUTION/ATTENTION

THE COMPLETE DOOR

D
OPERATOR IS PACKAGED IN TWO BOXES.

DOOR OPERATOR - 100lbs SET OF PANELS - 80lbs

DRAWN
fernandog 3/10/2008
CHECKED
TITLE
QA
INCLUDED IN DOOR OPERATOR BOX: INCLUDED IN DOOR PANEL BOX:
MFG

1 - DOOR OPERATOR 1 - SET OF DOORS

APPROVED

1 - OPERATOR DOOR SILL SIZE DWG NO

C BOX DRA
2 - OPERATOR MOUNTING
B
BRACKETS SCALE

3 2
1 - CAB DOOR SILL
1 - HARDWARE SET (SEE BELOW)

5.00
 2 SPEED VICTORY DOORS

INSTALLATION OF DOOR OPERATOR, CAB SILL

AND CAB DOORS

CAUTION! DO NOT REMOVE PROTECTIVE FILM COATING FROM ANY OF

THE ITEMS UNTIL ENTRANCE AND DOOR PANELS ARE FULLY INSTALLED
AND CONSTRUCTION IS FINISHED.

THE FOLLOWING SET OF HARDWARE PROVIDED TO INSTALL THE OPERATOR

AND DOORS. IF WOOD ANCHORS ARE REQUIRED THEY WILL NEED TO BE
ORDERED SEPARATELY.


# DESCRIPTION QTY IMAGE

1 PLAIN WASHER OD=20 - M10 10

2 TOOTHED WASHER - M10 14

3 PLAIN WASHER OD=30 - M10 3

4 SPLIT LOCK WASHER - M10 3

5 CARRAGE BOLT - M10x25 3

6 HEX NUT - M10 3

NOTE: HARDWARE IS NOT PROVIDED TO
7 FLAT HEAD SOCKET CAP SCREW - M10x30 2 SECURE THE TWO OPERATOR MOUNTING
BRACKETS TO THE CAB UNI-STRUT.
8 TOOTHED CROWN WASHER - M10 2

9 CAGE NUT - M10 16

10 SOCKET HEAD CAP SCREW - M10x20 14

11 ECCENTRIC WASHER - M10 4

4
12 SHIMS - 1mm & 2mm THICK
SETS

BUTTON HEAD SOCKET CAP SCREW - M5x10

13 3
(FOR TOE GUARD)

SERRATED FLANGE HEX NUT - M5

14 3
(FOR TOE GUARD)

15 GIB/GUIDE (WITH RUBBER) 4

5.01
 2 SPEED VICTORY DOORS

INSTALLATION OF DOOR OPERATOR

ONE WORKER REQUIRED

6mm ALLEN KEY TO INSTALL SCREWS

STEP 1: INSTALL THE MOUNTING BRACKETS AS SHOWN. DO NOT TIGHTEN.

5.02
 2 SPEED VICTORY DOORS

INSTALLATION OF DOOR OPERATOR

TWO WORKERS REQUIRED

TOOLS AND HARDWARE OF CUSTOMER’S CHOICE (HARDWARE IS NOT PROVIDED

TO SECURE MOUNTING BRACKETS TO UNI-STRUT)

CAUTION: OPERATOR IS HEAVY; 100 LBS.

STEP 2: ATTACH THE DOOR OPERATOR TO CAB, THEN SECURE MOUNTING

BRACKETS TO UNI-STRUTS.

UNI-STRUTS

5.03
 2 SPEED VICTORY DOORS

INSTALLATION OF DOOR OPERATOR

TWO WORKERS REQUIRED

TOOLS AND HARDWARE OF CUSTOMER’S CHOICE

ENSURE OPERATOR DOOR TRACK IS PARALLEL TO SILL! DO NOT 

STEP ON OPERATOR ONCE POSITIONED AND LEVELED.

STEP 3: SET DOOR TRACK HEIGHT PARALLEL TO CAB SILL. SEE TABLE BELOW.





CLEAR OPENING TRACK HEIGHT(H)

900(35 1/2") X 2000(78 3/4") 2065(81 15/16”)
900(35 1/2”) X 2100(82 5/8”) 2165(85 1/4") 
900(35 1/2”) X 2400(94 1/2”) 2465(97")

5.04
 2 SPEED VICTORY DOORS

INSTALLATION OF CAB SILL

ONE WORKER REQUIRED



10mm WRENCH

STEP 4: PLACE TRANSITION PIECE ONTO SILL AND SLIDE INTO PLACE. THEN
  

SECURE SILL USING HARDWARE SHOWN BELOW.

SILL
TRANSITION PIECE








SILL TRANSITION
 



 



 
 

 



  
  

5.05



  
 2 SPEED VICTORY DOORS

INSTALLATION OF CAB PANELS(DOORS)

ONE WORKER REQUIRED

  

10mm ALLEN KEY

ATTENTION: ENSURE DOORS ARE INSTALLED ALIGNED.

STEP 5: SNAP THREE FLOATING NUTS INTO OPERATOR HANGER. THEN

ATTACH DOOR PANELS (SLOW SPEED DOOR FIRST). SECURE DOOR PANELS
TO HANGERS WITH HARDWARE SHOWN BELOW.







5.06
 2 SPEED VICTORY DOORS

INSTALLATION OF CAB PANELS(DOORS)

ONE WORKER REQUIRED

10mm ALLEN KEY  

ATTENTION: ENSURE DOORS ARE 6(1/4”) ABOVE SILL.

STEP 6: SNAP TWO FLOATING NUTS INTO EACH DOOR GIB. SECURE DOOR
GIBS TO BOTTOM OF DOOR PANEL USING HARDWARE SHOWN BELOW





5.07
 2 SPEED VICTORY DOORS

INSTALLATION OF CAB PANELS(DOORS)

ONE WORKER REQUIRED

10mm ALLEN KEY AND SPECIALTY TOOL

ATTENTION: ENSURE DOORS ARE 6(1/4”) ABOVE SILL. ONCE SET ENSURE THAT
DOORS RUN FREELY BACK AND FORTH.

STEP 7: SET GAP BETWEEN BOTTOM OF DOOR PANELS AND SILL USING A
1/4” SHIM. ADD SHIM AT HANGER AS NECESSARY TO MAINTAIN A RUNNING
CLEARANCE OF 5(3/16”) BETWEEN EACH PANEL. MAKE FINAL ADJUSTMENTS
USING SPECIALTY TOOL TO ENSURE2.4PANELS ARE TRUE TO STRIKE AND
- DOOR PANEL ADJUSTMENT
RETURN POST. TIGHTEN ALL DOOR HARDWARE WHEN COMPLETE.
1. Open both doors all the way.
��������������������������������������������������������������������������������������
2. Shift doors on hanger until they are flush with cab return.
3. Once in place, rotate eccentric washer with special tool (provided in operator package) until door is level, t
����������������������������������������������������������������������������������
tighten bolts.
�����������������������������������������������������������������������������������������

������

Figure 2.4.1
SPECIALTY TOOL

5.08
 2 SPEED VICTORY DOORS

INSTALLATION OF LANDING ENTRANCE

GUIDE LEGEND:

REQUIRED WORKERS

REQUIRED TOOLS

CAUTION/ATTENTION 4 3

2 1

THE COMPLETE LANDING ENTRANCE IS SUPPLIED IN TWO BOXES.

D

LANDING MECHANISM - 100lbs SET

D OF PANELS - 80lbs

C
C

INCLUDED IN LANDING MECH BOX: INCLUDED IN DOOR PANEL BOX:

1 - LANDING MECHANISM 1 - SET OF DOORS
1 - STRIKE POST
1 - RETURN POST B
1 - LANDING SILL B

1 - HARDWARE SET (SEE BELOW)

3 - SILL SUPPORT BRACKETS

DRAWN
6.00
fernandog 3/10/2008
 2 SPEED VICTORY DOORS

INSTALLATION OF LANDING ENTRANCE

CAUTION! DO NOT REMOVE PROTECTIVE FILM COATING FROM ANY OF

THE ITEMS UNTIL ENTRANCE AND DOOR PANELS ARE FULLY INSTALLED
AND CONSTRUCTION IS FINISHED.

DESCRIPTION: FIRE RATED LANDING FRAME (CONCRETE)

THE FOLLOWING SET HARDWARE PROVIDED TO INSTALL THE LANDING
ATION
MECHANISM AND DOORS. IF WOOD ANCHORS ARE REQUIRED THEY WILL NEED
TO BE ORDERED SEPARATELY. REV
REVISION HISTORY
DESCRIPTION DATE APPROVED E.R.#
BEIGE FIRE RATED 2 COMPLETE SPEC REVISION 05/01/08 F.G.
HANISM

 
# DESCRIPTION QTY IMAGE # DESCRIPTION QTY IMAGE

1 PLAIN WASHER OD=20 - M10 10 10 GIB/GUIDE (WITH RUBBER) 4

4
2 TOOTHED LOCK WASHER - M10 14 11 SHIMS - 1mm & 2mm THK
SETS

BUTTON HEAD SOCKET CAP SCREW - M5x10

3 PLAIN WASHER OD=30 - M10 5 12 3
(FOR TOE GUARD)

4 SPLIT LOCK WASHER - M10 5 13 SQUARE NUT - M5 (FOR TOE GUARD) 3

5 CARRIAGE BOLT - M10x25 5 14 DOWEL (MASONARY ANCHOR) - M10x95 9

6 HEX NUT - M10 5 15 ALUMINIUM CLIP FOR WIRE 1

7 CAGE NUT (STANDARD) - M10 14 16 EXTENSION SPRING 465mm 1 N/A

8 SOCKET HEAD CAP SCREW - M10x20 14

9 ECCENTRIC WASHER - M10 4

6.01
SPECIFIED BY:
F.G.
DATE:
MAY 1/08
PAGE No.
1 OF 2
PART No.
127024
 2 SPEED VICTORY DOORS

INSTALLATION OF LANDING ENTRANCE

SILL SUPPORT ASSEMBLY (TYPE 1)

ONE WORKER REQUIRED

17mm WRENCH/ADJUSTABLE WRENCH

NOTE: DEPENDING WHEN YOU PURCHASED THE LANDING ENTRANCE, YOU

MAY RECEIVE A TYPE 1 OR TYPE 2 SILL SUPPORT ASSEMBLY..

STEP 1: ASSEMBLE THE LANDING SILL, TRANSITION, LANDING SILL SUPPORT

AND LANDING SILL SUPPORT BRACKETS AS SHOWN.
 

TRANSITION



SILL

SUPPORT
BRACKETS










6.02
 2 SPEED VICTORY DOORS

INSTALLATION OF LANDING ENTRANCE

SILL SUPPORT ASSEMBLY (TYPE 2)

ONE WORKER REQUIRED

17mm WRENCH/ADJUSTABLE WRENCH

STEP 1: ASSEMBLE THE LANDING SILL, TRANSITION, LANDING SILL SUPPORT

AND LANDING SILL SUPPORT BRACKET AS SHOWN.
 

TRANSITION

 

SILL

SUPPORT
BRACKET

6.03
 2 SPEED VICTORY DOORS

INSTALLATION OF LANDING ENTRANCE

MOUNTING THE SILL SUPPORT BRACKETS

ONE WORKER REQUIRED

17mm WRENCH/ADJUSTABLE WRENCH

ATTENTION: BEFORE PROCEEDING WITH INSTALLATION THERE MUST

BE A RUNNING PLATFORM AND SILL(S) ON THE PLATFORM.

  

LANDING SILL ASSEMBLY (SHOWN FULLY ASSEMBLED)

TYPE 1

SILL   

 SUPPORT BRACKETS 

TYPE 2

SILL

SUPPORT BRACKET

 

6.04
 2 SPEED VICTORY DOORS

INSTALLATION OF LANDING ENTRANCE

LOCATING THE LANDING SILL ASSEMBLY

TWO WORKERS REQUIRED

2 - 4FT LEVEL, MARKING TOOL, DRILL AND HAMMER

CONCRETE: 3/8” MASONRY DRILL
WOOD: 1/8” H.S.S. DRILL FOR PILOT HOLE

OPENING 900(35 1/2”) ‘X’: MIN 505(19 7/8”)

STEP 2: LOCATE LANDING SILL ASSEMBLY AS SHOWN AND SECURE. NOTE THAT
THE CAB SILL IS 100(3 15/16”) SHORTER THEN LANDING SILL. ALIGN LANDING
SILL SO THAT THE RETURN END OF THE SILL IS FLUSH WITH THE CAB SILL. THE
TRANSITION PIECE CAN BE READJUSTED LATER ON.

RETURN END

6.05
 2 SPEED VICTORY DOORS

TOP OF FINISHED FLOOR

30mm
(1 3/16”)

CAB
LANDING
SILL
SILL

SILL SUPPORT

NOTE:
OPENING 900(35 1/2”) ‘X’: MIN 1400(55”)

ATTENTION: RUNNING CLEARANCE BETWEEN CAB SILL AND LANDING MUST

BE 30(1 3/16”)

NOTE: LANDING SILL MUST BE LEVEL AND ADJUSTED TO CAB SILL AT ALL
LANDINGS.

MASONRY CONSTRUCTION WOOD CONSTRUCTION

1. MARK HOLES AS SHOWN. 1. MARK HOLES AS SHOWN.
2. DRILL TWO HOLES 3/8”Ø X 3” DEEP WITH 2. DRILL TWO HOLES 1/8”Ø X 3” DEEP WITH
MASONRY DRILL. A H.S.S. DRILL.
3. SECURE LANDING SILL ASSEMBLY WITH 3. SECURE LANDING SILL ASSEMBLY WITH
MASONRY ANCHORS (ITEM #14). WOOD LAGS.
4. USE REMAINING HOLES AS A TEMPLATE 4. USE REMAINING HOLES AS A TEMPLATE
TO ATTACH THE REST OF THE ANCHORS. TO ATTACH THE REST OF THE LAGS.

NOTE: IF CONSTRUCTION IS MASONRY NOTE: IN WOOD CONSTRUCTION TWO 2X10”

BLOCK, THE BLOCKS WILL NEED TO BE WOOD SUPPORTS SHOULD BE PRESENT TO
FILLED WITH CONCRETE SECURE THE WOOD LAGS

NOTE: WOOD LAGS ARE NOT PROVIDED FOR WOOD CONSTRUCTION INSTALLATION

6.06
 2 SPEED VICTORY DOORS

INSTALLATION OF LANDING ENTRANCE

ASSEMBLY OF LANDING ENTRANCE

TWO WORKERS REQUIRED

6mm ALLEN KEY, 17MM WRENCH/ADJUSTABLE WRENCH, PLASTIC CLAMPS

  

STEP 3: REMOVE THE SILL AND SUPPORT FROM THE ASSEMBLY LEAVING THE
SUPPORT BRACKET(S) ATTACHED IN THE HOISTWAY WALL. PLACE THE
 LANDING ENTRANCE ITEMS ON WOODEN HORSES OR STANDS AND ASSEMBLE
AS SHOWN BELOW.

STRIKE POST
SEE 6.08

LANDING
MECHANISM
(CAB HEADER)
SEE 6.10 AND
6.11
SILL SUPPORT
RETURN POST
SEE 6.08 AND 6.09
SEE 6.08

6.07

 2 SPEED VICTORY DOORS

INSTALLATION OF LANDING ENTRANCE

ASSEMBLY OF LANDING ENTRANCE

ONE WORKER REQUIRED

6mm ALLEN KEY

 

STEP 4: ATTACH THE STRIKE AND RETURN POSTS TO THE LANDING

MECHANISM(HEADER) USING THE HARDWARE ALREADY ATTACHED TO
THE POST BRACKETS.

CAGE NUT

CROWN
WASHER

SCREW
STRIKE POST RETURN POST

6.08

 2 SPEED VICTORY DOORS

INSTALLATION OF LANDING ENTRANCE

ASSEMBLY OF LANDING ENTRANCE

ONE WORKER REQUIRED

17mm WRENCH/ADJUSTABLE WRENCH

STEP 5: SLIDE AN EXTRA CARRIAGE BOLT THOUGH SILL. PLACE SILL ON TOP
OF POST BRACKETS AND ENSURE THAT TRANSITION IS ATTACHED TO THE
SILL. FASTEN THE TWO CARRIAGE BOLTS ATTACHING THE SILL TO THE POST
BRACKETS, LEAVING ONE CARRIAGE BOLT HANDING IN THE MIDDLE.

SILL

TRANSITION

 EXTRA BOLT

6.09
 2 SPEED VICTORY DOORS

INSTALLATION OF LANDING ENTRANCE

ASSEMBLY OF LANDING ENTRANCE

ONE WORKER REQUIRED

18mm/ADJUSTABLE WRENCH, STANDARD HAMMER

STEP 6: ATTACH THE DOOR RESTRICTOR MAGNET, USE THE PART’S PROVIDED
HARDWARE(NOT SHOWN IN LIST). THE RESTRICTOR MAGNET IS TO BE
INSTALLED ON THE STRIKE(CLOSING) SIDE.

STRIKE SIDE

6.10
 2 SPEED VICTORY DOORS

INSTALLATION OF LANDING ENTRANCE

MECHANISM BRACKETS

ONE WORKER REQUIRED

17mm WRENCH/ADJUSTABLE WRENCH

  

STEP 7: ATTACH MECHANISM SUPPORT BRACKETS AS SHOWN.


 


6.11






 2 SPEED VICTORY DOORS

INSTALLATION OF LANDING ENTRANCE

INSTALLATION OF ENTRANCE

TWO WORKERS REQUIRED

MARKING TOOL, DRILL AND HAMMER

CONCRETE: 3/8” MASONRY DRILL
WOOD: 3/8” X 3”LONG WOOD LAGS

ATTENTION: BE EXTRA CAREFUL WHEN INSTALLING THE ENTRANCE AS IT MAY

 NEED TO BE TILTED WHEN MOUNTING IN HOISTWAY.
  

STEP 8: FIT THE LANDING FRAME INSIDE THE

HOISTWAY, SECURE THE LANDING TO THE SILL
SUPPORT TO THE SILL SUPPORT BRACKETS
IN THE HOISTWAY.

NOTE: REMOVE THE NUTS AND WASHERS FROM



THE POST BRACKET. PLACE THE CARRIAGE BOLT

THOUGH SILL AND REFASTEN.

ONCE SILL SUPPORT IS SECURED, FIT

ANCHORS TO MECHANISM SUPPORT BRACKETS
AND SECURE. DEPENDING ON APPLICATION USE


APPROPRIATE ANCHORS AND TOOLS.


 


 



  





6.12
   
 2 SPEED VICTORY DOORS

INSTALLATION OF LANDING ENTRANCE

DOOR PANELS, LANDING MECHANISM WIRE

ONE WORKER REQUIRED

TENSION CABLE WIRE CRIMPERS(HEAVY DUTY)

STEP 9: TO INSTALL THE DOORS FOLLOW THE INSTRUCTIONS ON PAGES 5.06,

5.07 AND 5.08. ENSURE DOORS RUN FREELY ON LANDING SILL.


STEP 10: GUIDE THE CLOSING WIRE TO THE PULLEY. ONCE ITS ON THE
strikePULLEY
post. GUIDE THE WIRE AND TIE IT TO ONE END OF THE SPRING. ATTACH THE
OTHER END OF THE SPRING TO THE BRACKET ON THE POST. SECURE THE
WIRE AFTERWARDS WITH ITEM#15 - ALUMINUM CLIP (NOT SHOWN)

PULLEY

PULLEY

HANGER


WIRE

BRACKET

6.13
 2 SPEED VICTORY DOORS

INSTALLATION OF LANDING ENTRANCE

TOE GUARD

ONE WORKER REQUIRED

3mm ALLEN KEY, 8mm WRENCH



STEP 11: MOUNT TOE GUARD TO SILL SUPPORT USING HARDWARE SHOWN
BELOW.

AT THIS POINT, THE ENTRANCE SHOULD BE FULLY FUNCTIONAL WITH THE

CAB OPERATOR, ALL DOOR PANELS SHOULD RUN SMOOTH, AND WHEN FULLY
  

OPEN ALL PANELS SHOULD BE FLUSH TO EACH OTHER.

 





TOE GUARD

6.14 
 

 2 SPEED VICTORY DOORS

CONSTRUCTION OF LANDING ENTRANCE

WALLS TO THE FINISHED LANDING ELEVATOR
DOOR FRAMES
NOTE:
A. CAREFUL ATTENTION MUST BE GIVEN TO THIS PROCESS BOTH BY THE INSTALLING
ELEVATOR COMPANY AND THE GENERAL CONTRACTOR (GC) THAT IS TO FINISH OFF THE
LANDING ENTRANCE WALLS TO THE LANDING ELEVATOR ENTRANCES AFTER THE
ENTRANCES ARE SET IN POSITION BY THE INSTALLING ELEVATOR COMPANY.
B. THE ELEVATOR COMPANY RESPONSIBLE FOR THE INSTALLATION OF LANDING ENTRANCES
SHALL DISCUSS THESE SAFETY ISSUES WITH THE GC AND IT IS THE RESPONSIBILITY OF THE
GC TO DISCUSS THESE ISSUES WITH THE SUB TRADES COMPLETING THE LANDING
ENTRANCE WALLS TO THE LANDING ELEVATOR ENTRANCE.

1. MEET ON SITE WITH THE GENERAL CONTRACTOR (GC) THAT IS RESPONSIBLE FOR THE
CONSTRUCTION OF LANDING ENTRANCE WALLS TO THE LANDING ELEVATOR ENTRANCE
FRAME AND DEMONSTRATE THAT THE INTERFACE OF THE CAB DOORS, DOOR OPERATOR,
AND LANDING ENTRANCE DOORS WORK WITHOUT PROBLEMS. THEY MUST SEE THAT EACH
DOOR IS PROPERLY ALIGNED TO EACH OTHER AND THE CABS DOORS INTERFACE
PROPERLY TO EACH LANDING ENTRANCE WITHOUT INTERFERENCE.

2. LANDING ENTRANCE WALLS CAN BE FINISHED WITH EITHER DRYWALL (GYPSUM) OR

MASONRY AND WHEN USING EITHER ONE CAREFUL ATTENTION SHOULD BE PROVIDED
WHEN COMPLETING THIS WORK.

3. THE ELEVATOR COMPANY INSTALLING THE LANDING ELEVATOR ENTRANCE SHALL BE RE-
SPONSIBLE FOR PROVIDING THE APPROPRIATE DOCUMENT SHOWING EITHER THE MASON-
RY PROCESS OR DRYWALL PROCESS OF COMPLETING THE ENTRANCE WALLS.

4. THE INSTALLING ELEVATOR COMPANY SHALL BE RESPONSIBLE TO EXPLAIN TO THE GC

THAT THE PERSONS RESPONSIBLE FOR COMPLETING THE CONSTRUCTION OF THE EN-
TRANCE WALLS SHALL IN NO WAY DISTURB THE LOCATION OF FRAMES AS INSTALLED BY
THE ELEVATOR COMPANY.

7.00
 2 SPEED VICTORY DOORS

CONSTRUCTION OF LANDING ENTRANCE

WALLS TO THE FINISHED LANDING ELEVATOR
DOOR FRAMES

5. DO NOT REMOVE THE PROTECTIVE COATING FROM THE DOORS OR THE FRAMES UNTIL
THE ENTRANCE WALLS ARE COMPLETELY FINISHED.

6. IF THE GC REQUESTS TO USE THE ELEVATOR AS A CONSTRUCTION ELEVATOR IT IS VERY

IMPORTANT THEY TAKE FULL RESPONSIBILITY FOR ANY DAMAGE AND THEY MUST ALSO BE
MADE FULLY AWARE OF ALL SAFETY ISSUES. IT IS THE RECOMMENDATION OF OLS THAT
ONE PERSON FROM THE INSTALLING ELEVATOR COMPANY IS PRESENT WHILE THE EN-
TRANCE WALLS ARE BEING BUILT.

7. ALL OSHA OR EQUIVALENT SAFETY STANDARDS MUST BE FOLLOWED BY THE ELEVA-

TOR INSTALLING COMPANY AND THE GENERAL CONTRACTOR AS REQUIRED BY THE LOCAL
ENFORCING AUTHORITIES. IF FALL ARREST TRAINING IS REQUIRED TO BE GIVEN TO THE
WORKERS BEFORE STARTING TO WORK THIS MUST BE COMPLETED PRIOR TO STARTING
THE WORK AND THE FALL ARREST EQUIPMENT MUST BE MADE AVAILABLE IF NECESSARY.
EACH LANDING ENTRANCE MUST BE BARRICADED WITH OSHA STANDARD BARRICADES
AND NOT REMOVED UNTIL SUCH TIME AS THE ENTRANCE WALLS ARE COMPLETED AND IT
IS SAFE TO DO SO

8. UNDER NO CIRCUMSTANCE SHOULD SAFETY BE COMPROMISED, IT IS AN ABSOLUTE

REQUIREMENT THAT ALL PERSONNEL ARE TRAINED TO ALL THE NECESSARY SAFETY
STANDARDS WHILE INSTALLING THE ELEVATOR OR WORKING IN CLOSE PROXIMITY TO
THE ELEVATOR. IT IS THE RESPONSIBILITY OF THE INSTALLING ELEVATOR COMPANY, IT’S
EMPLOYEES, THE GENERAL CONTRACTOR, AND IT’S SUB TRADES THAT ALL EMPLOYEES
WORK SAFELY.

9. OLS TAKES ABSOLUTELY NO RESPONSIBLY FOR TRAINING THE ELEVATOR COMPANY

INSTALLING THE ENTRANCES OR THE COMPANY RESPONSIBLE FOR CONSTRUCTING THE
ENTRANCE WALL TO THE ELEVATOR LANDING ENTRANCE.

7.01
 2 SPEED VICTORY DOORS

ELECTRICAL DIAGRAM OF BOARD

Board Calibration

Auto-Learn can also be

Accomplished by the following:

1. Remove power supply

2. Jump JP2
3. Re-attach power supply
4. Auto-Learn will take place
5. Remove jumper
6. Complete

������

8.00
 2 SPEED VICTORY DOORS

ELECTRICAL DIAGRAM OF BOARD - MAIN

CONNECTIONS
JP11 JP10

AUTO-LEARN

JP4

JP17

JP16

JP8

JP1 24V DC
ONLY

JP6

8.01
 2 SPEED VICTORY DOORS

SET UP OF THE CONTROL BOARD

SET UP OF THE VICTORY CONTROL BOARD

Please ensure of the following before setting the doors.

¾Guide shoes in place
¾Cleanliness of lines and ways
¾Any damage to the door panels, operator, control board etc.
¾Electric contacts to the control board
¾Cleanliness of the mating and sliding wheels and relevant guide ways

WARNING
¾Do not lubricate the guide ways
¾Do not lubricate the transmission belts
¾Do not lubricate the wheel bearings

The Victory Doors control boards comes pre-programmed and pre-wired. Please make the
connections to the terminals as follows.

Connector JP 1(L1 – L2)

L1(+) with Ferrites L2 (-) with Ferrites
Ensure that 24V DC is supplied to the Victory Doors control board.

Connector JP2
Data acquisition/Auto-learn
For every test and adjustment ALWAYS do an auto-learn cycle.

An Auto-Learn cycle is can be done removing the power.

1. Jump JP2 with provided jumper
2. Power up the board
3. Let the cycle run
4. Remove the Jumper

Connector JP4
Connection for programming tool
To change the parameters in the control board connect the programming tool to JP4 and set the
switch to (P). Use the (+) and (-) buttons to search through the parameters. Press (S) to select
the parameter and adjust with (+) and (-) buttons. Press (T) to test any function changed. Once
finished put the programmer back to (N) and continue with the adjustment of the Door.

Connector JP6 (M1 – M2)

Motor Connection – Connect motor to here. On a RH Operator ensure that M1=Red and
M2=Black. On a LH Operator ensure that M1=Black and M2=Red.

Connector JP8 (F1 – F2)

Closing Contacts and Optic Barrier
Parameter U1=00 optic barrier input (contact NA)
Parameter U1=01 input of the end of closing contact
Normally U1=01

9.00
Connection for programming tool
To change the parameters in the control board connect the programming tool to JP4 and set the
switch to (P). Use the (+) and (-) buttons to search through the parameters. Press (S) to select
the parameter and adjust with (+) and (-) buttons. Press (T) to test any function changed. Once
2 SPEED VICTORY DOORS
finished put the programmer back to (N) and continue with the adjustment of the Door.

Connector JP6 (M1 – M2)

SET UP OF THE CONTROL BOARD
Motor Connection – Connect motor to here. On a RH Operator ensure that M1=Red and
M2=Black. On a LH Operator ensure that M1=Black and M2=Red.

Connector JP8 (F1 – F2)

Closing Contacts and Optic Barrier
Parameter U1=00 optic barrier input (contact NA)
Parameter U1=01 input of the end of closing contact
Normally U1=01

ATTENTION: DURING THE FIRST POWER UP OF THE VICTORY DOORS CONTROL

BOARD PLEASE PRESS THE CALIBRATION BUTTON WITH JP10 AND JP11
DISCONNECTED.

THE CALIBRATION BUTTON CAN ALSO BE USED TO CLEAR THE BOARD OF SETTINGS
AND SET TO FACTORY DEFAULTS.

Connector JP10 (FCA – FCC – CAM)

Output of the following information on the NC contacts for the operation panel:
1- Opening limit switch terminals 1 and 2 – FCA (Open)
2- Closing limit switch terminals 3 and 4 – FCC (Closing)
3- Photocell or sensitive edge intervention terminals 5 and 6 – CAM

Connector JP11 (TAP – TCP – EXF – COM)

Door opening/closing management
1 - Opening command from the panel Terminal / TAP
2 - Closing command from the panel Terminal / TCP
3 - Command of photocell by-pass for fireman service Terminal / EXF
4 - Negative in output (24 Volts/0 Volts) Terminal / COM
Manual commands can be given to the above by a 0v signal.

Connector JP16 (CPA)

Open limit sensor

Connector JP17 (ENC.M)

Encoder Connection

The Victory Doors control board had been set up to the following parameters. If changes are
necessary on the field, the following parameters are listed as follows.

(Table) V1.6
NOTE: PROGRAMMING TOOL NOT INCLUDED

Connection of the Light Curtains (OLS Supplied):

The light curtains have reverse polarity and short circuit protection. Please refer to the
following diagrams to ensure proper connection to your controller.

Transmitter

Receiver

Please refer to the following diagram if you want to connect your (OLS Supplied) light
9.01
curtains to the board. Please also used the connector provided.
 2 SPEED VICTORY DOORS
REVISION HISTORY
REV DESCRIPTION DATE APPROVED E.R.#
CONTROL BOARD PARAMETERS V1.6

VICTORY DOOR PARAMATERS (OLS DESIGN) V1.6

GE CODE DESCRIPTION MIN MAX DEFAULT NOTE
P0 OPENING SPEED 15 25 20
P1 CLOSING SPEED 10 25 20
P2 CLOSING FORCE LIMIT 10 25 15
P3 FINAL OPENING SPEED 4 12 5
P4 FINAL CLOSING SPEED 2 12 5
P5 INITIAL ("RELEASE") OPENING SPEED 9 16 10
P6 OPEN DOOR HOLDING FORCE 8 14 10
P7 CLOSED DOOR HOLDING FORCE 8 14 12
P8 DISTANCE TRAVELED AT OPENING SPEED 10 20 12
P9 ACCELERATION TIME (OPEN/CLOSE) 2 10 5
PA SPEED CONTROL TIME PERIOD 10 25 18
PB LIGHT CURTAIN DISABLE DISTANCE 10 25 15
PHOTO CELL SELECTION
PC 0
0=BYPASS, 1=ACTIVE, 3=DEFAULT
ACCELETARION DISTANCE
PD 1 3 2
1=SHORT, 2=NORMAL, 3=LONG
DISTANCE COVERED AT LOW SPEED TO
PE 4 16 7
COMPLETE OPENING
DISTANCE COVERED AT LOW SPEED TO
PF 10 25 15
COMPLETE CLOSING
U0 MAX CLOSING SPEED IN FIRE RECALL PH-1 10 25 10
INPUT F1-F2
U1 0 1 1
PHOTCELL=0, DOOR CLOSED=1
DOOR OPEN SIGNAL
U2 0 1 1
PULSE=0, SUSTAINED=1
ENCODER LOCATION
U3 1
MOTOR=0(-) OR 1(+), PULLEY=6(N/A)
DOOR RE-OPENING DEVICE CONNECTION
U4 TO DOOR OPERATOR=0 1
TO CONTROL PANEL=1
U5 RAMP UP CURRENT 5 25 10

** PLEASE REFER TO DOC# 151897 FOR PROGRAM LOAD PROCEDURE

9.02
 2 SPEED VICTORY DOORS

OPERATOR RUNNING CYCLE

OPENING CYCLE
SPEED OPEN DOOR CLOSED DOOR

TIME

CLOSING CYCLE
SPEED OPEN DOOR CLOSED DOOR

TIME

9.03
 2 SPEED VICTORY DOORS

TROUBLESHOOTING
After completing autoͲlearn (data i. Using programming device, go through program
acquisition cycle) cycle, doors will parameters to ensure that values are all set to default.
continually open and close. Modifying many parameters at once may cause this.
Ensure that autoͲlearn is performed after every
change.
Doors will close but FA (door open i. Ensure door contacts are connected to JP8 (F1 & F2)
sensor) light will remain lit on door and the reed sensor connected to JP16 (CPA).
operator board. Reversing the two will cause this respective problem.

Doors will open but FC (door close

sensor) light will remain lit on door
operator board.
The LED’s on the door operator board i. Ensure that the power supply is plugged into location
do not turn on. JP1 (L1 positive & L2 negative)
ii. Ensure the voltage supplied is 24v DC
iii. Ensure the fuse located at F2 is still good. If not,
replace using a 4 amp quick fuse.
The door will not open when i.
instructed to by the controller. Perform data acquisition cycle as per section 6.0. ReͲ
try door open instruction.
ii. Ensure controller sends a 0v signal when instructing
doors to open on TAP.
iii. Disconnect connector JP11 (TAP – TCP – EXF – COM).
Jumper (hold jumper) pins COM to TAP on Victory
board.
iv. Jumper pins COM to TCP; if doors open then motor
polarity has been reversed.
v. If the door forces itself to close in the closed position,
Check the signals coming from the controller.
The doors will not close when i. Perform data acquisition cycle as per section 6.0. ReͲ
instructed to by the controller. try door close instruction.
ii. Ensure controller sends a 0v signal when instructing
doors to close on TCP.
iii. Disconnect connector JP11 (TAP – TCP – EXF – COM).
Jumper pins COM to TCP on Victory board.
iv. Jumper pins COM to TAP; if doors close then the
polarity of the motor has been reversed.
v. If the door forces itself to open in the open position,
check the signals coming from controller.
No response to open / close i. Perform data acquisition cycle, as per section 6.0. ReͲ
instruction from controller. try door instructions from controller.
ii. Ensure ground is connected to main controller. If not,
door operator will not respond to open / close signals.
iii. Ensure that controller is supplying a 0v signal.

10.00
 2 SPEED VICTORY DOORS

TROUBLESHOOTING
Doors will not shut fully and the clutch i. Plug programming device into terminal JP4. Increase
(skate) will not fully collapse. the values of parameters U5, P7 and P2 (programming
instructions as per section 5.0). Perform data
acquisition cycle (section 6.0) to reset door operator.
ReͲtry.
ii. Ensure that installation of the operator has been done
properly, the clutch must make contact with skate.
Doors will shake when closing. i. Ensure that doors have been installed to 1/4” of the
ground. After that raise doors by 1/8”.
ii. Ensure that the encoder is plugged into JP17 (ENC.M.).
Perform data acquisition (section 6.0). ReͲtry.
iii. If rattling is occurring, check guide shoes (Figure 2.3.1).
LED FC will not turn on when doors i. Check continuity between the two wires of the door
are closed and car gate signal not ok contact switch when doors are closed. If continuity
when doors are closed does not exist, adjust the position of the contacts in
order to ensure contact when doors are closed.
ii. Check for damage on the contacts. If damaged replace
contacts.

Doors are moving extremely slow, i. Ensure the belt for the encoder is not too tight. Allow
cannot fully close / open. 1cm compression from both sides when belt is
squeezed with two fingers.
ii. Ensure belt for motor is not too tight. Allow belt to
compress a minimum of 1cm from both sides when
squeezed with two fingers.
iii. Ensure that AutoͲlearn cycle has been performed after
changes, too many changes to the parameters without
performing auto learn will cause this problem.
Overheating occurs i. Ensure that motor polarities are not reversed.
Reversed polarities will cause board to over heat.

Parameter E”X” shows up on the i. An Error has occurred within the board. Power down
programming tool. and remove all connections to Victory Control board.
Where X is a number from 0Ͳ9 Attach all connections and perform AutoͲlearn once
more, Please set all parameters to default and restart the
setting up of the doors.

Please contact Technical Support at 1-800-567-3557 for any questions.

10.01