ETS-05-XX-A

Surface sensing electronic thermostat

Product Overview
The Raychem ETS-05-XX-A electronic surface sensing
thermostat provides accurate temperature control for
heating cables.
The ETS-05-XX-A is available in two versions. The ETS-05-
L2-A is for temperatures up to 199°C (390°F), while the ETS-
05-H2-A can be used for temperatures up to 499°C (930°F).
The maximum nominal load is 24 A for both thermostats.
Temperature setting is accurate via digital rotary switches
inside the enclosure.
cing
Tra

The ETS-05-XX-A has a LED indicator which indicates the

t-
2-A ea
5-L ic H t
S-0 ron sta
ET lect rmo
E he
T

status of the thermostat (powered on/off), the status of the

heat-tracing cable (powered on/off) and the status of the
sensor. In case of sensor failure the thermostat can switch
to an on or off state, depending upon the users requirement.
product characteristics
ETS-05-L1-A-KIT ETS-05-H1-A
ETS-05-L2-A-KIT ETS-05-H2-A
Application Surface sensing-Pipe Mount Surface sensing-Wall Mount
Area of use Hazardous area: Zone 1 or Zone 2 (Gas) or Zone 21 (Dust) CL I, DIV 2
Ordinary Locations

Approvals/certification
In Combination with Pipe Stand: When Used without Pipe Stand:
CL I, ZN1 AEx e ia mb IIC T5..T3 Gb CL I, ZN 1 AEx e ia mb IIC T5 Gb
ZN 21 AEx tb IIIC T100°C..T150°C ZN 21 AEx tb IIIC T100°C
Ex e ia mb IIC T5..T3 Gb Ex e ia mb IIC T5 Gb
Ex tb IIIC T100°C..T150°C Db Ex tb IIIC T100°C Db
CLI, DIV 2, Groups B, C, D CL I, DIV 2, Groups B, C, D
Hazardous Locations CL II, DIV 2, Groups E, F, G CL II, DIV 2, Groups E, F, G
Class III Class III
TYPE 4X, IP66 TYPE 4X, IP66
Product specification
Temperature setpoint range 0°C to 199°C (32°F to 390°F) 0°C to 499°C (32°F to 930°F)
Temperature measurement range –55°C to 260°C (-67°F to 500°F) –55°C to 585°C (-67°F to1085°F)
Sensor type 100 Ohm RTD, included in ETS-05-Lx-A-KIT 100 Ohm RTD (not included with
(part of the pipe stand) thermostat)
Maximum sensor lead resistance 20 Ohm 20 Ohm
Ingress protection IP66 IP66
Switching accuracy ±1 K at 5°C (41°F) ±1 K at 5°C (41°F), 2°C at 499°C (930°F)
Switching differential (Hysteresis) ≈ 3°C (5°F) ≈ 3°C (5°F)
Output relay Single Pole change over type (SPST) Single Pole change over type (SPST)
Switching capacity 24 A resistive load 24 A resistive load
Ambient temperature range –40°C to + 60°C (–40°F to + 140°F) –40°C to + 60°C (–40°F to + 140°F)
Supply voltage L1-A: 99-132 VAC -10% H1-A: 99-132 VAC -10%
L2-A: 195-277 VAC -2.5% H2-A: 195-277 VAC -2.5%
Internal power consumption 3 VA 3 VA
Terminal size max. 6 mm2 (10AWG) max. 6 mm2 (10AWG)
Cable entries 2 x 3/4" 2 x 3/4"
1 x Pipe stand 1 x 3/4" Gland for power cable in
Mounting Method JB-RTD-STAND (included in kit) Wall-Mount

INDUSTRIAL HEAT TRACING SOLUTIONS Raychem-DS-H59252-ETS05-EN-1703 1/4

ETS-05
LEd STATUS INdIcATIONS
Green: ETS-05 powered on, Green: ETS-05 powered on,
heat-tracing cable off heat-tracing cable off
Yellow: ETS-05 powered on, Yellow: ETS-05 powered on,
heat-tracing cable on heat-tracing cable on
Red flashing: Sensor failure - controller Red flashing: Sensor failure - controller
in fail safe mode in fail safe mode

Dimensions (in mm)

4.8 in (122 mm)
4.17 in (106 mm)

0 901 401

78
23

23
23
1
1
0 456 401
4.72 in (120 mm)
3.22 in (82 mm)

Power Terminals

1 2 3 4 5 6 7

Line Neutral Neutral Line Supply Earth Earth Earth

Out Out Supply

Terminals 2 and 3 are joined electrically

Terminals 5, 6 and 7 are joined electrically

Sensor/Failure Mode Select Terminals

1 2 3 4

Link 3-4 removed = Output OFF

Link 3-4 fitted = Output ON

Terminals 1 to 3 allow for the connection of a three wire PT100 sensor.

Terminals 3 to 4 allow the user to select the default heating status on sensor error.
Without a link fitted the heating will turn OFF if a sensor error is detected.
With a link fitted the heating will turn ON if a sensor error is detected (default).

2/4 Raychem-DS-H59252-ETS05-EN-1703 INDUSTRIAL HEAT TRACING SOLUTIONS

 ETS-05
Typical wiring diagram for direct switching

PE

IEC: Max 32A

NEC/CEC: Max 30A *
30 mA

ETS-05

L1 1 2 3 4
out in PE PE PE

Fail-Safe
option

Link 3-4 removed = Output OFF

Link 3-4 fitted = Output ON
* Circuit breaker configurations may vary
according to local standards/requirements

Mounting method
JB-RTD-STAND: P000001997 SB-101: 990944-000

Ordering details
ETS-05 Thermostats ETS-05-H1-A: 1244-015664
(Thermostat Only) ETS-05-H2-A: 1244-015665

ETS-05 Thermostat Kits ETS-05-L1-A KIT: 1244-017701

(Includes Pipe Stand) ETS-05-L2-A KIT: 1244-017702

INDUSTRIAL HEAT TRACING SOLUTIONS Raychem-DS-H59252-ETS05-EN-1703 3/4

 WWW.PENTAIRTHERMAL.COM

NORTH AMERICA Europe, Middle East, Africa Asia Pacific Latin America
Tel: +1.800.545.6258 Tel: +32.16.213.511 Tel: +86.21.2412.1688 Tel: +1.713.868.4800
Fax: +1.800.527.5703 Fax: +32.16.213.603 Fax: +86.21.5426.3167 Fax: +1.713.868.2333
Tel: +1.650.216.1526 [email protected] [email protected] [email protected]
Fax: +1.650.474.7711
[email protected]

Pentair, BTV, QTVR, XTV, KTV, and VPL are owned by Pentair or its global affiliates. All other trademarks are the property of their respective owners.
Pentair reserves the right to change specifications without prior notice.

© 2016-2017 Pentair.

INDUSTRIAL HEAT TRACING SOLUTIONS Raychem-DS-H59252-ETS05-EN-1703 4/4