Scribd
Upload
48 views

Adaptive Multirate: Slide

This document discusses Adaptive Multirate (AMR) speech coding, which allows the speech codec to change during a call based on interference conditions to improve speech quality. AMR supports 8 different codec modes between 4.75-12.2 kbps and allows up to 4 modes in an Active Codec Set. Thresholds are used to determine which codec mode to use based on the channel quality. AMR requires support in all network nodes like MSC, BSC, MS and BTS.

Uploaded by

jedossous
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
48 views

Adaptive Multirate: Slide

This document discusses Adaptive Multirate (AMR) speech coding, which allows the speech codec to change during a call based on interference conditions to improve speech quality. AMR supports 8 different codec modes between 4.75-12.2 kbps and allows up to 4 modes in an Active Codec Set. Thresholds are used to determine which codec mode to use based on the channel quality. AMR requires support in all network nodes like MSC, BSC, MS and BTS.

Uploaded by

jedossous
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Slide

AMR
Adaptive Multirate

03813-LZU 108 3704 Uae Rev C Slide 1 (12)

Why AMR?

• Improved speech quality at low C/I


• Apply tighter frequency reuse in a network with high AMR
capable MS penetration
• Possible to change speech codec during the call,
depending on interference conditions

03813-LZU 108 3704 Uae Rev C Slide 2 (12)

03813-LZU 108 3704 Uae Rev C 1


Slide

Concepts
• Active Codec Set (ACS) A set of one to four different codec modes
(all using the same channel rate)
• Codec Mode A codec rate used within a codec set. The actual
bit rate on Air-interface
• Speech Version Version of speech coding. Sub pools in TRA pool.

FR SPV 1 = “normal Full Rate”


FR SPV 2 = “enhanced Full Rate”
FR SPV 3 = “AMR Full Rate”
HR SPV 1 = “normal Half Rate”

• Channel Rate Full Rate (22,8 kbps gross bit rate on air interface)
and Half Rate (11,4 kbps gross bit rate)

03813-LZU 108 3704 Uae Rev C Slide 3 (12)

AMR transcoder:

• There are 8 different codec modes available:


– 12,2 kbps
– 10,2 kbps
– 7,95 kbps
– 7,40 kbps
– 6,70 kbps
– 5,90 kbps
– 5,15 kbps
– 4,75 kbps

• An Active Codec Set may contain up to 4 codec modes, all


using the same channel rate
• All codec rates can be used in FR channel

03813-LZU 108 3704 Uae Rev C Slide 4 (12)

03813-LZU 108 3704 Uae Rev C 2


Slide

Codec mode adaptation

• Channel rate selected by network at call setup


• Active Codec Set communicated to the MS and BTS
• The codec modes in an ACS is defined as:
CODEC_MODE_1 - Represents the codec mode with the lowest bit rate
CODEC_MODE_2 - Represents the second lowest mode (if ACS includes more than one mode)
CODEC_MODE_3 - Represents the third lowest mode (if ACS includes more than two modes)
CODEC_MODE_4 - Represents the highest mode (if ACS includes four modes)

03813-LZU 108 3704 Uae Rev C Slide 5 (12)

Thresholds for a codec set


Thresholds and hysteresis values
are used to determine which codec
mode to use for a certain channel
quality (C/I)

• THR_1/2/3 is given as integer


values between 0 and 63 (unit: 0,5
dB)
• HYST_1/2/3 is given as integer
values between 0 and 15 (unit: 0,5
dB)

03813-LZU 108 3704 Uae Rev C Slide 6 (12)

03813-LZU 108 3704 Uae Rev C 3


Slide

Multirate configurations Full Rate (FR)


Full Rate Codec Set 1 Decision thresholds and hysteresis
CODEC_MODE_1 4,75 kbps values for FR Codec Set 1
Threshold Value (dB) Hysteresis Value (dB)
CODEC_MODE_2 5,9 kbps
THR_1 6 HYST_1 1
CODEC_MODE_3 6,7 kbps
THR_2 10,5 HYST_2 1,5
CODEC_MODE_4 10,2 kbps THR_3 10,5 HYST_3 1,5

Full Rate Codec Set 2 Decision thresholds and hysteresis


CODEC_MODE_1 4,75 kbps
values for FR Codec Set 2
Threshold Value (dB) Hysteresis Value (dB)
CODEC_MODE_2 5,9 kbps
THR_1 6 HYST_1 1
CODEC_MODE_3 7,95 kbps
THR_2 8,5 HYST_2 1,5

CODEC_MODE_4 12,2 kbps THR_3 12,5 HYST_3 1,5

03813-LZU 108 3704 Uae Rev C Slide 7 (12)

Example of different codec modes (AMR-FR)

30
28
26
24
Speech Quality [dBQ]

22
20
18
16
14
12 FR 1
FR 2
10
FR 3
8
FR env
6
4
2
0
-4 -3 -2 -1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

C/I [dB]

03813-LZU 108 3704 Uae Rev C Slide 8 (12)

03813-LZU 108 3704 Uae Rev C 4


Slide

Inband signalling (BTS <-> MS)

03813-LZU 108 3704 Uae Rev C Slide 9 (12)

AMR affected nodes

• AMR requires support in all NW MSC


nodes, i.e MSC, BSC, MS and
BTS
– All TRUs must support AMR (dTRU,
EDGE dTRU or EDGE sTRU) BSC
– Transcoder R6 needed

BTS

03813-LZU 108 3704 Uae Rev C Slide 10 (12)

03813-LZU 108 3704 Uae Rev C 5


Slide

Parameter summary

• AMRSUPPORT Indicates if the feature AMR is turned ON or OFF and


also which full rate codec set codec set (hardcoded in
BSC) that shall be used within the BSC

03813-LZU 108 3704 Uae Rev C Slide 11 (12)

Parameters
Parameter Default Rec. Value range
value value
AMRSUPPORT 0 - 0=off

1=Fullrate codec set 1

2=Full rate codec set 2

3=Not defined

4=Not defined

03813-LZU 108 3704 Uae Rev C Slide 12 (12)

03813-LZU 108 3704 Uae Rev C 6

You might also like