Scribd
Upload
4K views1 page

Baofeng Uv 5r Cheat Sheet

- To program a memory channel, select the desired frequency in VFO mode, then enter the offset frequency, direction, and CTCSS tone if desired. Save the receive frequency to a memory channel number, then save the transmit frequency to the same channel number. - You cannot overwrite existing memory channels. Check the display to see if a channel is already programmed before saving frequencies. - To delete a memory channel, enter the delete menu and select the channel number to be deleted.

Uploaded by

Baud Wolf
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
4K views1 page

Baofeng Uv 5r Cheat Sheet

- To program a memory channel, select the desired frequency in VFO mode, then enter the offset frequency, direction, and CTCSS tone if desired. Save the receive frequency to a memory channel number, then save the transmit frequency to the same channel number. - You cannot overwrite existing memory channels. Check the display to see if a channel is already programmed before saving frequencies. - To delete a memory channel, enter the delete menu and select the channel number to be deleted.

Uploaded by

Baud Wolf
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
You are on page 1/ 1

BAOFENG UV-5R Program a memory channel:

(Note: You cannot overwrite a memory channel. If the channel


Turn ON/OFF and Adjust volume: turn knob on top name in the display is CH-NNN it means there is programming in
place for channel NNN; if it merely says NNN, then the channel has
INITIAL SET UP: not been programmed and you may safely enter any new receiving
Turn off dual monitor mode: MENU-7-MENU-0-MENU-EXIT and transmitting frequencies, etc. See Delete a Memory Channel
MENU-3-6-MENU-0-MENU-EXIT below)
MENU-3-7-MENU-0-MENU-EXIT In VFO mode (toggle VFO/MR)
MENU-3-9-MENU-0-MENU-EXIT  Select the VFO-A mode (toggle the A/B button) Look for the
Change Power Level: MENU-2-MENU-0 (1 for low)-MENU-EXIT  arrow in the top line in the display. Everything relies on
Lock Keypad: Press and hold LOCK, repeat to unlock this step !!
Memory Recall (Memory mode) and VFO mode: the VFO/MR  Select desired band: Band repeat to desired band
button toggles between frequency mode and memory  Enter desired frequency: six digits on number pad
mode.  Enter offset frequency: MENU-2-6-MENU-00.600 for 2M
Change Frequency: (144-158 MHz) 05.000 for 70 cm band (420-450 MHz)-
 In memory mode, use buttons MENU-EXIT (delete this step for simplex)
 In VFO mode, press six number buttons  Enter offset direction: MENU-2-5-MENU-0 for simplex
Change Band: BAND, repeat until desired band (1 for + /2 for - )-MENU-EXIT
Turn off Repeater Offset: MENU-2-5-MENU-0 (1 for + / 2 for - ) -  Set CTCSS Tone: MENU-1-3-MENU-(enter tone frequency
MENU-EXIT on number pad- no decimal needed) – MENU-EXIT
Reverse Repeater Input and Output: SCAN/REV toggles, repeat to  Save receive frequency in memory: MENU-2-7-MENU-enter
undo memory channel on number pad -MENU-EXIT
 Save Transmit frequency in memory:- SCAN/REV -MENU-2-
 Note: Repeater offsets for two meters are typically 7-MENU-(enter same memory channel number on number
negative below 147 MHz and positive for 147 MHZ and pad) –MENU-EXIT-SCAN/REV
above. To access the memorized channel, remember to return to memory
mode from VFO mode by once again toggling VFO/MR
For 70 cm, offsets are positive below 445 MHz, and
negative above 445 MHz
Delete a memory channel: MENU-2-8-MENU-(channel number to
be deleted) – MENU-EXIT

You might also like